Pretreatment of Low-Density Polyethylene(LDPE)with physicochemical methods before biodegradation has been demonstrated as an effective strategy.The pretreatment of LDPE exhibited alterations in molecular structure,red...Pretreatment of Low-Density Polyethylene(LDPE)with physicochemical methods before biodegradation has been demonstrated as an effective strategy.The pretreatment of LDPE exhibited alterations in molecular structure,reducing hydrophobicity and decreasing tensile strength.Additionally,pretreating LDPE enhanced microbial biodegradability to improve biofilm formation and significantly reduced the physical weight of LDPE film.AS3–8 consortia exhibited a maximum weight loss of 8.0%±0.5%after 45 days of incubation.While Bacillus sp.AS3 and Sphingobacterium sp.AS8 demonstrated LDPE weight loss of 5.03%±1.6%and 1.6%±0.5%,respectively.The structure of LDPE was altered after incubation with the bacterial strains,resulting in a reduction in the intensity of functional groups,including C=O,C=C,N–H,and C–N.The carbonyl index(CI)of LDPE also decreased by 7.17%after the consortia AS3–8 degradation.Consortia AS3–8 significantly impacted the physical properties of LDPE by reducing the water contact angle(WCA),decreasing to 64.21°±3.69°,and tensile strength(TS),decreasing to 17.97±0.3 MPa.Moreover,the esterase activity was measured through 45 days of incubation.SDS-PAGE analysis of the AS3–8 consortia revealed bands at 35,48,and 70 kDa molecular weights,similar to known enzymes like laccase and esterase.Furthermore,SEM observations showed rough,cracked surfaces on pretreated LDPE,with biofilms present after incubation with the bacterial strains.GC–MS analysis revealed that AS3–8 consortia produced depolymerized chemicals,including alkanes,aldehydes,and esters.The LDPE biodegradation pathway was elucidated.This study addresses critical knowledge gaps in improving plastic degradation efficiency.展开更多
In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-f...In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.展开更多
Under equivalent stiffness conditions,material substitution based on a thin-walled design is crucial for the lightweight of components.Developing high-performance steels with both high-yield strength and excellent duc...Under equivalent stiffness conditions,material substitution based on a thin-walled design is crucial for the lightweight of components.Developing high-performance steels with both high-yield strength and excellent ductility has become a key focus in fields like aerospace and lowaltitude flight.The novel low-density steel presented here exhibits a yield strength of 1000 MPa,which is 2-3 times higher than conventional low-alloy high-strength steels,while maintaining an elongation of about 18.7%.By combining ex-situ experimental characterization with a phase mechanical response model based on the iso-work theory and the von Mises equivalent method,the role of heterogeneous deformation-induced strengthening was revealed.The calculated values align closely with experimental results.This exceptional performance is attributed to a multiphase heterogeneous microstructure,where fresh martensite,bainite/tempered martensite,and deformation-induced martensite act as hard regions.These regions release micro-stresses through inhomogeneous cooperative deformation with soft ferrite,enabling multiple plastic deformation mechanisms and stress concentration relief.This research offers new insights into optimizing microstructures through mechanical metallurgy,which is crucial for producing high-performance,lightweight components.展开更多
Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understand...Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understanding of their formation,evolution,and mechanisms of explosive development is essential for improving forecasts of extreme weather events and mitigating associated impacts.Potential vorticity(PV),which is closely related to cyclone dynamics,serves as a valuable diagnostic tool in the study of ECs.In this study,two wintertime ECs of differing intensity over the Northwestern Pacific Ocean are analyzed to examine how different atmospheric processes influence PV generation and the rapid development of ECs.The maximum deepening rates of the two ECs are 2.81 Bergeron(called EC1) and 1.52 Bergeron(referred to as EC2).Results indicate that different stages of EC evolution are closely associated with PV tendency changes at different atmospheric levels.Using the PV tendency equation,during the explosive development of EC1,latent heat release may trigger the downward propagation of upper-level PV.For EC2,latent heat release notably enhances low-level PV,directly contributing to its rapid intensification.To validate these findings,sensitivity tests are conducted using the Weather Research and Forecasting model,with latent heat release turned off in the microphysical scheme for both cases.The results confirm the crucial role of latent heat release in generating low-level PV,further revealing that latent heat release contributes more to the explosive development of EC2 than that of EC1.展开更多
α-Synuclein accumulation and transmission are vital to the pathogenesis of Parkinson's disease,although the mechanisms underlying misfoldedα-synuclein accumulation and propagation have not been conclusively dete...α-Synuclein accumulation and transmission are vital to the pathogenesis of Parkinson's disease,although the mechanisms underlying misfoldedα-synuclein accumulation and propagation have not been conclusively determined.The expression of low-density lipoprotein receptor–related protein 1,which is abundantly expressed in neurons and considered to be a multifunctional endocytic receptor,is elevated in the neurons of patients with Parkinson's disease.However,whether there is a direct link between low-density lipoprotein receptor–related protein 1 andα-synuclein aggregation and propagation in Parkinson's disease remains unclear.Here,we established animal models of Parkinson's disease by inoculating monkeys and mice withα-synuclein pre-formed fibrils and observed elevated low-density lipoprotein receptor–related protein 1 levels in the striatum and substantia nigra,accompanied by dopaminergic neuron loss and increasedα-synuclein levels.However,low-density lipoprotein receptor–related protein 1 knockdown efficiently rescued dopaminergic neurodegeneration and inhibited the increase inα-synuclein levels in the nigrostriatal system.In HEK293A cells overexpressingα-synuclein fragments,low-density lipoprotein receptor–related protein 1 levels were upregulated only when the N-terminus ofα-synuclein was present,whereas anα-synuclein fragment lacking the N-terminus did not lead to low-density lipoprotein receptor–related protein 1 upregulation.Furthermore,the N-terminus ofα-synuclein was found to be rich in lysine residues,and blocking lysine residues in PC12 cells treated withα-synuclein pre-formed fibrils effectively reduced the elevated low-density lipoprotein receptor–related protein 1 andα-synuclein levels.These findings indicate that low-density lipoprotein receptor–related protein 1 regulates pathological transmission ofα-synuclein from the striatum to the substantia nigra in the nigrostriatal system via lysine residues in theα-synuclein N-terminus.展开更多
Neurotoxic astrocytes are a promising therapeutic target for the attenuation of cerebral ischemia/reperfusion injury.Low-density lipoprotein receptor,a classic cholesterol regulatory receptor,has been found to inhibit...Neurotoxic astrocytes are a promising therapeutic target for the attenuation of cerebral ischemia/reperfusion injury.Low-density lipoprotein receptor,a classic cholesterol regulatory receptor,has been found to inhibit NLR family pyrin domain containing protein 3(NLRP3)inflammasome activation in neurons following ischemic stroke and to suppress the activation of microglia and astrocytes in individuals with Alzheimer’s disease.However,little is known about the effects of low-density lipoprotein receptor on astrocytic activation in ischemic stroke.To address this issue in the present study,we examined the mechanisms by which low-density lipoprotein receptor regulates astrocytic polarization in ischemic stroke models.First,we examined low-density lipoprotein receptor expression in astrocytes via immunofluorescence staining and western blotting analysis.We observed significant downregulation of low-density lipoprotein receptor following middle cerebral artery occlusion reperfusion and oxygen-glucose deprivation/reoxygenation.Second,we induced the astrocyte-specific overexpression of low-density lipoprotein receptor using astrocyte-specific adeno-associated virus.Low-density lipoprotein receptor overexpression in astrocytes improved neurological outcomes in middle cerebral artery occlusion mice and reversed neurotoxic astrocytes to create a neuroprotective phenotype.Finally,we found that the overexpression of low-density lipoprotein receptor inhibited NLRP3 inflammasome activation in oxygen-glucose deprivation/reoxygenation injured astrocytes and that the addition of nigericin,an NLRP3 agonist,restored the neurotoxic astrocyte phenotype.These findings suggest that low-density lipoprotein receptor could inhibit the NLRP3-meidiated neurotoxic polarization of astrocytes and that increasing low-density lipoprotein receptor in astrocytes might represent a novel strategy for treating cerebral ischemic stroke.展开更多
Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer ...Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.展开更多
Fe-28Mn-(10-12)Al-(0.8-1.4)C(wt.%)steels were designed to investigate the influence of varying Al and C content on precipitation behavior ofκ-carbide and its contribution to the strength of high-Mn low-density steels...Fe-28Mn-(10-12)Al-(0.8-1.4)C(wt.%)steels were designed to investigate the influence of varying Al and C content on precipitation behavior ofκ-carbide and its contribution to the strength of high-Mn low-density steels.Results reveal that both Al and C elements promoteκ-carbide precipitation,with C having a more pronounced effect.In near-rapidly solidified 10Al steel strips,increasing C content from 0.8wt.%to 1.4wt.%raises theκ-carbide size from 9.6 nm to 38.2 nm,accompanied by volume fraction increase from 10.2vol.%to 29.8vol.%.In comparison,the average size and volume fraction ofκ-carbides in 12Al0.8C steel are only 11.4 nm and 17.8vol.%,respectively.Higher Al and C content reduces the lattice mismatch between austenite andκ-carbides,thus promoting nucleation ofκ-carbides.Notably,the increase in C content results in a greater reduction in the Gibbs free energy ofκ-carbide,leading to a stronger driving force forκ-carbide formation.Consequently,as the C content increases from 0.8wt.%to 1.4wt.%,the interaction betweenκ-carbides and dislocations transforms from particle cutting to bypassing,and the maximum precipitation strengthening ofκ-carbides reaches 583 MPa.The construction of the relationship between Al and C content andκ-carbide precipitation in this study would provide valuable insights for alloy design of high-Mn steels.展开更多
Carbon can change the phase components of low-density steels and influence the mechanical properties.In this study,a new method to control the carbon content and avoid the formation ofδ-ferrite by decarburization tre...Carbon can change the phase components of low-density steels and influence the mechanical properties.In this study,a new method to control the carbon content and avoid the formation ofδ-ferrite by decarburization treatment was proposed.The microstructural changes and mechanical characteristics with carbon content induced by decarburization were systematically examined.Crussard-Jaoul(C-J)analysis was employed to examine the work hardening characteristics during the tensile test.During decarburization by heat treatments,the carbon content within the austenite phase decreased,while Mn and Al were almost unchanged;this made the steel with full austenite transform into the austenite and ferrite dual phase.Meanwhile,(Ti,V)C carbides existed in both matrix phase and the mole fraction almost the same.In addition,the formation of other carbides restrained.Carbon loss induced a decrease in strength due to the weakening of the carbon solid solution.For the steel with the single austinite,the deformation mode of austenite was the dislocation planar glide,resulting in the formation of microbands.For the dual-phase steel,the deformation occurred by the dislocation planar glide of austenite first,with the increase in strain,the cross slip of ferrite took place,forming dislocation cells in ferrite.At the late stage of deformation,the work hardening of austinite increased rapidly,while that of ferrite increased slightly.展开更多
While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and ...While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.展开更多
Loss-of-function variants of low-density lipoprotein receptor-related protein 5(LRP5)can lead to reduced bone formation,culminating in diminished bone mass.Our previous study reported transcription factor osterix(SP7)...Loss-of-function variants of low-density lipoprotein receptor-related protein 5(LRP5)can lead to reduced bone formation,culminating in diminished bone mass.Our previous study reported transcription factor osterix(SP7)-binding sites on the LRP5 promoter and its pivotal role in upregulating LRP5 expression during implant osseointegration.However,the potential role of SP7 in ameliorating LRP5-dependent osteoporosis remained unknown.In this study,we used mice with a conditional knockout(c KO)of LRP5 in mature osteoblasts,which presented decreased osteogenesis.The in vitro experimental results showed that SP7 could promote LRP5 expression,thereby upregulating the osteogenic markers such as alkaline phosphatase(ALP),Runt-related transcription factor 2(Runx2),andβ-catenin(P<0.05).For the in vivo experiment,the SP7 overexpression virus was injected into a bone defect model of LRP5 c KO mice,resulting in increased bone mineral density(BMD)(P<0.001)and volumetric density(bone volume(BV)/total volume(TV))(P<0.001),and decreased trabecular separation(Tb.Sp)(P<0.05).These data suggested that SP7 could ameliorate bone defect healing in LRP5 c KO mice.Our study provides new insights into potential therapeutic opportunities for ameliorating LRP5-dependent osteoporosis.展开更多
Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for...Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for these compounds serves a dual-purpose:enabling the fabrication of high-performance sensors for detection and guiding the design of efficient adsorbents for environmental remediation.This study investigated the host–vip recognition behavior of perethylated pillar[n]arenes toward two aromatic nitro molecules,1-chloro-2,4-dinitrobenzene and picric acid.Various techniques including^(1)H NMR,2D NOESY NMR,and UV-vis spectroscopy were employed to explore the binding behavior between pillararenes and aromatic nitro vips in solution.Moreover,valuable single crystal structures were obtained to elucidate the distinct solid-state assembly behaviors of these vips with different pillararenes.The assembled solid-state supramolecular structures observed encompassed a 1:1 host–vip inclusion complex,an external binding complex,and an exo-wall tessellation complex.Furthermore,based on the findings from these systems,a pillararene-based test paper was developed for efficient picric acid detection,and the removal of picric acid from solution was also achieved using pillararenes powder.This research provides novel insights into the development of diverse host–vip systems toward hazardous compounds,offering potential applications in environmental protection and explosive detection domains.展开更多
Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientatio...Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.展开更多
To further reduce the explosive thickness and to improve the bonding quality of titanium/steel composite plates,explosive welding experiments of TA1/Q235 were conducted using a low detonation velocity explosive(53#)un...To further reduce the explosive thickness and to improve the bonding quality of titanium/steel composite plates,explosive welding experiments of TA1/Q235 were conducted using a low detonation velocity explosive(53#)under the guidance of the explosive welding lower limit principle with the flyer plate thicknesses of 1,2,and 4 mm and gaps of 3,6,and 8 mm.The weldability window for titanium/steel explosive welding was calculated,and a quantitative relationship between dynamic and static process parameters was developed.Aβ-V_(p) high-speed inclined collision model was proposed,and two-dimensional numerical simulations for the explosive welding tests were performed using the smoothed particle hydrodynamics(SPH)algorithm,revealing the growth evolution mechanisms of the typical waveform morphology characteristics.Through microstructural characterization techniques,such as optical microscope,scanning electron microscope,energy dispersive spectrometer,and electron backscattered diffractometer,and mechanical property tests in terms of shear strength,bending performance,and impact toughness,the microstructure and mechanical properties of the interfaces of explosively welded TA1/Q235 composite plates were investigated.Results show that the quality of interface bonding is excellent,presenting typical waveform morphology with an average interface shear strength above 330 MPa and an average impact toughness exceeding 81 J.All samples can be bent to 180°without significant delamination or cracking defects.展开更多
High-performance pure nickel N6/steel 45#composite plate(N6/45#)was prepared using explosive welding technique.The microstructure of the interface and nearby regions was characterized and analyzed by optical microscop...High-performance pure nickel N6/steel 45#composite plate(N6/45#)was prepared using explosive welding technique.The microstructure of the interface and nearby regions was characterized and analyzed by optical microscope,scanning electron microscope,electron backscatter diffraction,and mechanical property testing,and the microstructural features and mechanical properties of the explosive welding interface were explored.The results show that along the direction of explosive welding,the pure nickel N6/steel 45#composite plate interface gradually evolves from a flat bond to a typical wavy bond.The grains at the crests and troughs exhibit high heterogeneity,and the closer to the interface,the finer the grains.Recrystallization and low-stress deformation bands are formed at the bonding interface.Nanoindentation tests reveal that plastic deformation occurs in the interfacial bonding zone,and the nanohardness values in the crest regions are higher than that in the trough regions.The tensile strength of the N6/45#interface is 599.8 MPa,with an average shear strength of 326.3 MPa.No separation phenomenon is observed between N6 and 45#after the bending test.展开更多
The low-density medium-Mn steel is widely studied and applied in the automobile and construction machinery due to the low costs and high strength-ductility.Adding lightweight elements,such as aluminum,is considered an...The low-density medium-Mn steel is widely studied and applied in the automobile and construction machinery due to the low costs and high strength-ductility.Adding lightweight elements,such as aluminum,is considered an efficient way to reduce the density of the steels.A novel 5Al-5Mn-1.5Si-0.3C(wt%)low-density and high-strengthδ-ferrite/martensite(δ-F/M)steel was designed in this study.The study indicated that the designed steel annealed at 1080℃was characterized by an excellent combination of tensile strength of 1246 MPa and density of 7.24 g/cm^(3).Microscopic characterization shows that the higher prior-austenite volume fraction(i.e.,martensite plus retained austenite)significantly increases the tensile strength,and the strip-like martensite and retained austenite(M&RA)mixture benefits elongation.High martensite fraction owns higher origin geometrically necessary dislocations,contributing to better work-hardening behaviors.Concurrently,the synergistic presence of M&RA mixtures’volume fraction and morphology enhances their capability to absorb stress and obstruct crack propagation,significantly improving mechanical performance.The extended strength formula,accounting for the contribution of the M&RA mixture,is consistent with the quantitative agreement observed in experimental results.These insights provide a valuable technological reference for the knowledge-based design and prediction of the mechanical properties of low-density and high-strength steel.展开更多
It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the m...It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the macro-and micro-mixing affect the reactor performance was still controversial in publications.In this work,a cold-flow LDPE autoclave with multi-feedings was scaled down(1/2)from an industrial reactor and built to systematically investigate the macro-and micro-mixing characteristics of fluid by experiments.Furthermore,the effects of macro-and micro-mixing on the polymerization were comprehensively analyzed.The results showed that according to the delay time t_(d) and macro-mixing times tM calculated from residence time distribution(RTD)curves,the macro-mixing states are significantly different at various axial positions(h/H),especially at lower agitation Reynolds number Re.But with the increase of Re,since the circulation flow in the reactor is strengthened,the t_(d) for each feed gradually decreases to 0,and the t_(M) at different axial positions tend to be identical.For micro-mixing,the qualities of micro-mixing at different axial positions are similar,and the average micro-mixing time t_(m) in the reactor decreases exponentially with the increase of Re.Moreover,a fitting model was established.Through the comparison of the characteristic times of macro-mixing(t_(d),t_(M)),micro-mixing(t_(m))and elementary reactions within the industrial range of Re,it can be concluded that the properties of LDPE products are dominated by the macro-mixing behavior,and the consumption of initiators is affected by both the macro-and micro-mixing behaviors.This conclusion is of great significance for the design,optimization and operation of LDPE reactors.展开更多
The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after so...The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after solution treatment was single austenitic phase.The austenite grain size increased with solution temperature and time.A model was established to show the relationship between temperature,time and austenite grain size for the experimental steel.In addition,as the solution temperature increased,the strength decreased,while the elongation first increased and then decreased.This decrease in elongation after solution treatment at 1100℃ for 90 min is contributed to the over-coarse austenite grains.However,after solution treatment at 900℃ for 90 min,the strength-elongation product reached the highest value of 44.4 GPa%.As the austenite grain size increased,the intensity of<111>//tensile direction fiber decreased.This was accompanied by a decrease in dislocation density,resulting in a lower fraction of low-angle grain boundaries and a lower work hardening rate.Therefore,the austenite grain size has a critical influence on the mechanical properties of the low-density steels.Coarser grains lead to a lower yield strength due to the Hall-Petch effect and a lower tensile strength because of lower dislocation strengthening.展开更多
Martensitic-based microstructures in low-density steels offer high strength and improved specific strength,combined with the lightweight effect of aluminum(Al).However,while Al effectively reduces density,it simultane...Martensitic-based microstructures in low-density steels offer high strength and improved specific strength,combined with the lightweight effect of aluminum(Al).However,while Al effectively reduces density,it simultaneously promotes the formation of coarse ferrite and expands the two-phase(α+γ)intercritical temperature range.Thus,increasing the Al content for higher weight reduction inevitably leads to ferrite formation and impedes further strengthening.To achieve both high strength and duc-tility while incorporating ferrite,it is crucial to elucidate the effects of ferrite fraction,size,and dis-tribution on mechanical properties and deformation behavior,particularly in relation to phase interac-tions.In this study,three model steels were developed through controlled annealing temperatures,pro-ducing distinct triplex microstructures comprising ferrite,martensite,and retained austenite(RA).The role of each phase in strain partitioning was investigated using ex-situ microscopic digital image cor-relation and electron back-scattered diffraction analysis.Key findings reveal that the martensitic matrix ensures an ultrahigh strength level(1758 MPa),while a moderate fraction(∼17%)and homogeneous dis-tribution of intercritical-ferrite(IC-ferrite)enable sustainable strain-hardening behavior by delaying the transformation-induced plasticity(TRIP)effect.Strain partitioning into IC-ferrite reduces local strains in the martensitic matrix,preventing early exhaustion of the TRIP effect and facilitating ductile fracture behavior.This strategy leverages the presence of ferrite,offering significant advantages for applications requiring both ultrahigh strength and ductility.展开更多
BACKGROUND Esophageal cancer(EC)is one of the most common malignancies worldwide,and lymph node(LN)metastasis remains one of the leading causes of EC recurrence.Metabolic disorders critically affect cancer progression...BACKGROUND Esophageal cancer(EC)is one of the most common malignancies worldwide,and lymph node(LN)metastasis remains one of the leading causes of EC recurrence.Metabolic disorders critically affect cancer progression,and lipid levels are closely associated with the occurrence of EC and several other tumor types.This study analyzed pretreatment lipid levels to determine their association with LN metastasis.AIM To dissect the possible mechanisms underlying LN metastasis and clarify the prognostic role of lipid profiles in EC.METHODS Serum lipid levels and clinicopathological information were retrospectively collected from 294 patients,and risk factors for LN metastasis were confirmed using a logistic regression model.Latent factors were explored using information from publicly accessible databases and immunofluorescence and immunohistochemical staining techniques.RESULTS High serum levels of low-density lipoprotein(LDL)cholesterol promote LN metastasis in EC,while high-density lipoprotein cholesterol has the opposite role.Information of a public database revealed that LDL receptors LRP5 and LRP6 are highly expressed in ECs,and LRP6 overexpression positively correlated with the infiltration of B lymphocytes and a poor prognosis.Immunofluorescence and immunohistochemical staining revealed that the expression of LRP6 and infiltrated B lymphocytes in patients with≥1 regional LN metastasis,containing N1-3(N+group)were significantly higher than those in the N0 group.LRP6 was also highly expressed in the B lymphocytes of the N+group.There was no difference in CXCL13 expression between the N+and N0 groups.However,CXCR5 expression was significantly higher in the N0 group than in the N+group.CONCLUSION High serum LDL levels can promote LN metastasis in EC,and the mechanisms may be related to LRP6 expression and the infiltration of B lymphocytes.展开更多
文摘Pretreatment of Low-Density Polyethylene(LDPE)with physicochemical methods before biodegradation has been demonstrated as an effective strategy.The pretreatment of LDPE exhibited alterations in molecular structure,reducing hydrophobicity and decreasing tensile strength.Additionally,pretreating LDPE enhanced microbial biodegradability to improve biofilm formation and significantly reduced the physical weight of LDPE film.AS3–8 consortia exhibited a maximum weight loss of 8.0%±0.5%after 45 days of incubation.While Bacillus sp.AS3 and Sphingobacterium sp.AS8 demonstrated LDPE weight loss of 5.03%±1.6%and 1.6%±0.5%,respectively.The structure of LDPE was altered after incubation with the bacterial strains,resulting in a reduction in the intensity of functional groups,including C=O,C=C,N–H,and C–N.The carbonyl index(CI)of LDPE also decreased by 7.17%after the consortia AS3–8 degradation.Consortia AS3–8 significantly impacted the physical properties of LDPE by reducing the water contact angle(WCA),decreasing to 64.21°±3.69°,and tensile strength(TS),decreasing to 17.97±0.3 MPa.Moreover,the esterase activity was measured through 45 days of incubation.SDS-PAGE analysis of the AS3–8 consortia revealed bands at 35,48,and 70 kDa molecular weights,similar to known enzymes like laccase and esterase.Furthermore,SEM observations showed rough,cracked surfaces on pretreated LDPE,with biofilms present after incubation with the bacterial strains.GC–MS analysis revealed that AS3–8 consortia produced depolymerized chemicals,including alkanes,aldehydes,and esters.The LDPE biodegradation pathway was elucidated.This study addresses critical knowledge gaps in improving plastic degradation efficiency.
基金supported by the National Natural Science Foundation of China(Grant Nos.52271307,52061135107,52192692,11802025)the Liao Ning Excellent Youth Fund Program(Grant No.2023JH3/10200012)+1 种基金the Liao Ning Revitalization Tal-ents Program(Grant No.XLYC1908027)the Fundamental Research Funds for the Central Universities(Grant Nos.DUT20RC(3)025,DUT20TD108,DUT20LAB308)。
文摘In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.
基金funded by the National Natural Science Foundation of China(No.51974134)the Innovation Ability Promotion Plan Project of Hebei Province,China(No.24461002D)。
文摘Under equivalent stiffness conditions,material substitution based on a thin-walled design is crucial for the lightweight of components.Developing high-performance steels with both high-yield strength and excellent ductility has become a key focus in fields like aerospace and lowaltitude flight.The novel low-density steel presented here exhibits a yield strength of 1000 MPa,which is 2-3 times higher than conventional low-alloy high-strength steels,while maintaining an elongation of about 18.7%.By combining ex-situ experimental characterization with a phase mechanical response model based on the iso-work theory and the von Mises equivalent method,the role of heterogeneous deformation-induced strengthening was revealed.The calculated values align closely with experimental results.This exceptional performance is attributed to a multiphase heterogeneous microstructure,where fresh martensite,bainite/tempered martensite,and deformation-induced martensite act as hard regions.These regions release micro-stresses through inhomogeneous cooperative deformation with soft ferrite,enabling multiple plastic deformation mechanisms and stress concentration relief.This research offers new insights into optimizing microstructures through mechanical metallurgy,which is crucial for producing high-performance,lightweight components.
基金financially supported by the National Key R&D Program of China (No. 2022YFC3004204)the National Natural Science Foundation of China (No. 42275001)the Natural Science Foundation of Shandong Province (No. ZR2022MD038)。
文摘Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understanding of their formation,evolution,and mechanisms of explosive development is essential for improving forecasts of extreme weather events and mitigating associated impacts.Potential vorticity(PV),which is closely related to cyclone dynamics,serves as a valuable diagnostic tool in the study of ECs.In this study,two wintertime ECs of differing intensity over the Northwestern Pacific Ocean are analyzed to examine how different atmospheric processes influence PV generation and the rapid development of ECs.The maximum deepening rates of the two ECs are 2.81 Bergeron(called EC1) and 1.52 Bergeron(referred to as EC2).Results indicate that different stages of EC evolution are closely associated with PV tendency changes at different atmospheric levels.Using the PV tendency equation,during the explosive development of EC1,latent heat release may trigger the downward propagation of upper-level PV.For EC2,latent heat release notably enhances low-level PV,directly contributing to its rapid intensification.To validate these findings,sensitivity tests are conducted using the Weather Research and Forecasting model,with latent heat release turned off in the microphysical scheme for both cases.The results confirm the crucial role of latent heat release in generating low-level PV,further revealing that latent heat release contributes more to the explosive development of EC2 than that of EC1.
基金supported by the Natural Science Foundation of Guangxi Zhuang Automomous Region,Nos.2019GXNSFDA245015(to MC),2022GXNSFBA035654(to HL)the National Natural Science Foundation of China,Nos.82360241(to MC),82304876(to HL)+1 种基金Scientific Research and Technology Development Project of Guilin City,Nos.20220139-3(to MC),20210218-5(to HL)Guangxi Medical and Health Key Discipline Construction Project(to QL)。
文摘α-Synuclein accumulation and transmission are vital to the pathogenesis of Parkinson's disease,although the mechanisms underlying misfoldedα-synuclein accumulation and propagation have not been conclusively determined.The expression of low-density lipoprotein receptor–related protein 1,which is abundantly expressed in neurons and considered to be a multifunctional endocytic receptor,is elevated in the neurons of patients with Parkinson's disease.However,whether there is a direct link between low-density lipoprotein receptor–related protein 1 andα-synuclein aggregation and propagation in Parkinson's disease remains unclear.Here,we established animal models of Parkinson's disease by inoculating monkeys and mice withα-synuclein pre-formed fibrils and observed elevated low-density lipoprotein receptor–related protein 1 levels in the striatum and substantia nigra,accompanied by dopaminergic neuron loss and increasedα-synuclein levels.However,low-density lipoprotein receptor–related protein 1 knockdown efficiently rescued dopaminergic neurodegeneration and inhibited the increase inα-synuclein levels in the nigrostriatal system.In HEK293A cells overexpressingα-synuclein fragments,low-density lipoprotein receptor–related protein 1 levels were upregulated only when the N-terminus ofα-synuclein was present,whereas anα-synuclein fragment lacking the N-terminus did not lead to low-density lipoprotein receptor–related protein 1 upregulation.Furthermore,the N-terminus ofα-synuclein was found to be rich in lysine residues,and blocking lysine residues in PC12 cells treated withα-synuclein pre-formed fibrils effectively reduced the elevated low-density lipoprotein receptor–related protein 1 andα-synuclein levels.These findings indicate that low-density lipoprotein receptor–related protein 1 regulates pathological transmission ofα-synuclein from the striatum to the substantia nigra in the nigrostriatal system via lysine residues in theα-synuclein N-terminus.
基金supported by the National Natural Science Foundation of China,No.82201460(to YH)Nanjing Medical University Science and Technology Development Fund,No.NMUB20210202(to YH).
文摘Neurotoxic astrocytes are a promising therapeutic target for the attenuation of cerebral ischemia/reperfusion injury.Low-density lipoprotein receptor,a classic cholesterol regulatory receptor,has been found to inhibit NLR family pyrin domain containing protein 3(NLRP3)inflammasome activation in neurons following ischemic stroke and to suppress the activation of microglia and astrocytes in individuals with Alzheimer’s disease.However,little is known about the effects of low-density lipoprotein receptor on astrocytic activation in ischemic stroke.To address this issue in the present study,we examined the mechanisms by which low-density lipoprotein receptor regulates astrocytic polarization in ischemic stroke models.First,we examined low-density lipoprotein receptor expression in astrocytes via immunofluorescence staining and western blotting analysis.We observed significant downregulation of low-density lipoprotein receptor following middle cerebral artery occlusion reperfusion and oxygen-glucose deprivation/reoxygenation.Second,we induced the astrocyte-specific overexpression of low-density lipoprotein receptor using astrocyte-specific adeno-associated virus.Low-density lipoprotein receptor overexpression in astrocytes improved neurological outcomes in middle cerebral artery occlusion mice and reversed neurotoxic astrocytes to create a neuroprotective phenotype.Finally,we found that the overexpression of low-density lipoprotein receptor inhibited NLRP3 inflammasome activation in oxygen-glucose deprivation/reoxygenation injured astrocytes and that the addition of nigericin,an NLRP3 agonist,restored the neurotoxic astrocyte phenotype.These findings suggest that low-density lipoprotein receptor could inhibit the NLRP3-meidiated neurotoxic polarization of astrocytes and that increasing low-density lipoprotein receptor in astrocytes might represent a novel strategy for treating cerebral ischemic stroke.
基金Opening Foundation of Key Laboratory of Explosive Energy Utilization and Control,Anhui Province(BP20240104)Graduate Innovation Program of China University of Mining and Technology(2024WLJCRCZL049)Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX24_2701)。
文摘Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.
基金supported by the National Natural Science Foundation of China(Nos.52301058 and 52271034)the China Postdoctoral Science Foundation(No.2023M732183)+3 种基金the Postdoctoral Fellowship Program of CPSF(No.GZB20230399)the Key scientific and technological project in Ningbo City(No.2022Z056)supported by the Independent Research Project of State Key Laboratory of the Advanced Special Steel,Shanghai Key Laboratory of Advanced Ferrometallurgy,Shanghai University(SKLASS 2023-Z12)the Science and Technology Commission of Shanghai Municipality(No.19DZ2270200).
文摘Fe-28Mn-(10-12)Al-(0.8-1.4)C(wt.%)steels were designed to investigate the influence of varying Al and C content on precipitation behavior ofκ-carbide and its contribution to the strength of high-Mn low-density steels.Results reveal that both Al and C elements promoteκ-carbide precipitation,with C having a more pronounced effect.In near-rapidly solidified 10Al steel strips,increasing C content from 0.8wt.%to 1.4wt.%raises theκ-carbide size from 9.6 nm to 38.2 nm,accompanied by volume fraction increase from 10.2vol.%to 29.8vol.%.In comparison,the average size and volume fraction ofκ-carbides in 12Al0.8C steel are only 11.4 nm and 17.8vol.%,respectively.Higher Al and C content reduces the lattice mismatch between austenite andκ-carbides,thus promoting nucleation ofκ-carbides.Notably,the increase in C content results in a greater reduction in the Gibbs free energy ofκ-carbide,leading to a stronger driving force forκ-carbide formation.Consequently,as the C content increases from 0.8wt.%to 1.4wt.%,the interaction betweenκ-carbides and dislocations transforms from particle cutting to bypassing,and the maximum precipitation strengthening ofκ-carbides reaches 583 MPa.The construction of the relationship between Al and C content andκ-carbide precipitation in this study would provide valuable insights for alloy design of high-Mn steels.
基金financially supported by the National Natural Science Foundation of China(Nos.U2141207,52171111,and 52001083)the Youth Talent Project of China National Nuclear Corporation(No.CNNC2021Y-TEPHEU01)+3 种基金the China Postdoctoral Science Foundation(No.2020M681077)the Natural Science Foundation of Heilongjiang,China(No.LH2019E030)the Heilongjiang Postdoctoral Science Foundation,China(No.LBH-Z19125)he Heilongjiang Touyan Innovation Team Program,China,and the Natural Science Foundation of Heilongjiang(No.LH2020E060)。
文摘Carbon can change the phase components of low-density steels and influence the mechanical properties.In this study,a new method to control the carbon content and avoid the formation ofδ-ferrite by decarburization treatment was proposed.The microstructural changes and mechanical characteristics with carbon content induced by decarburization were systematically examined.Crussard-Jaoul(C-J)analysis was employed to examine the work hardening characteristics during the tensile test.During decarburization by heat treatments,the carbon content within the austenite phase decreased,while Mn and Al were almost unchanged;this made the steel with full austenite transform into the austenite and ferrite dual phase.Meanwhile,(Ti,V)C carbides existed in both matrix phase and the mole fraction almost the same.In addition,the formation of other carbides restrained.Carbon loss induced a decrease in strength due to the weakening of the carbon solid solution.For the steel with the single austinite,the deformation mode of austenite was the dislocation planar glide,resulting in the formation of microbands.For the dual-phase steel,the deformation occurred by the dislocation planar glide of austenite first,with the increase in strain,the cross slip of ferrite took place,forming dislocation cells in ferrite.At the late stage of deformation,the work hardening of austinite increased rapidly,while that of ferrite increased slightly.
基金supported by the National Natural Science Foundation of China(Grant Nos.12002156,11972185,12372136)Research Fund of State Key Laboratory of Mechanics and Control for Aerospace Structures(Grant No.MCMS-I-0222K01)。
文摘While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.
文摘Loss-of-function variants of low-density lipoprotein receptor-related protein 5(LRP5)can lead to reduced bone formation,culminating in diminished bone mass.Our previous study reported transcription factor osterix(SP7)-binding sites on the LRP5 promoter and its pivotal role in upregulating LRP5 expression during implant osseointegration.However,the potential role of SP7 in ameliorating LRP5-dependent osteoporosis remained unknown.In this study,we used mice with a conditional knockout(c KO)of LRP5 in mature osteoblasts,which presented decreased osteogenesis.The in vitro experimental results showed that SP7 could promote LRP5 expression,thereby upregulating the osteogenic markers such as alkaline phosphatase(ALP),Runt-related transcription factor 2(Runx2),andβ-catenin(P<0.05).For the in vivo experiment,the SP7 overexpression virus was injected into a bone defect model of LRP5 c KO mice,resulting in increased bone mineral density(BMD)(P<0.001)and volumetric density(bone volume(BV)/total volume(TV))(P<0.001),and decreased trabecular separation(Tb.Sp)(P<0.05).These data suggested that SP7 could ameliorate bone defect healing in LRP5 c KO mice.Our study provides new insights into potential therapeutic opportunities for ameliorating LRP5-dependent osteoporosis.
基金supported by the fundamental research funds of Zhejiang Sci-Tech University(No.22212286-Y)the Natural Science Foundation of Zhejiang Province(No.LQ24B040003)。
文摘Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for these compounds serves a dual-purpose:enabling the fabrication of high-performance sensors for detection and guiding the design of efficient adsorbents for environmental remediation.This study investigated the host–vip recognition behavior of perethylated pillar[n]arenes toward two aromatic nitro molecules,1-chloro-2,4-dinitrobenzene and picric acid.Various techniques including^(1)H NMR,2D NOESY NMR,and UV-vis spectroscopy were employed to explore the binding behavior between pillararenes and aromatic nitro vips in solution.Moreover,valuable single crystal structures were obtained to elucidate the distinct solid-state assembly behaviors of these vips with different pillararenes.The assembled solid-state supramolecular structures observed encompassed a 1:1 host–vip inclusion complex,an external binding complex,and an exo-wall tessellation complex.Furthermore,based on the findings from these systems,a pillararene-based test paper was developed for efficient picric acid detection,and the removal of picric acid from solution was also achieved using pillararenes powder.This research provides novel insights into the development of diverse host–vip systems toward hazardous compounds,offering potential applications in environmental protection and explosive detection domains.
基金Anhui Province Key Research and Development Plan(2022a05020021)China Coal Science and Industry Group Chongqing Research Institute Independent Research and Development Project(2023YBXM58)。
文摘Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.
基金Jiangsu Provincial Natural Science Foundation of China(BK20211232)2023 Major Science and Technology Projects of Nanjing City(202309011)。
文摘To further reduce the explosive thickness and to improve the bonding quality of titanium/steel composite plates,explosive welding experiments of TA1/Q235 were conducted using a low detonation velocity explosive(53#)under the guidance of the explosive welding lower limit principle with the flyer plate thicknesses of 1,2,and 4 mm and gaps of 3,6,and 8 mm.The weldability window for titanium/steel explosive welding was calculated,and a quantitative relationship between dynamic and static process parameters was developed.Aβ-V_(p) high-speed inclined collision model was proposed,and two-dimensional numerical simulations for the explosive welding tests were performed using the smoothed particle hydrodynamics(SPH)algorithm,revealing the growth evolution mechanisms of the typical waveform morphology characteristics.Through microstructural characterization techniques,such as optical microscope,scanning electron microscope,energy dispersive spectrometer,and electron backscattered diffractometer,and mechanical property tests in terms of shear strength,bending performance,and impact toughness,the microstructure and mechanical properties of the interfaces of explosively welded TA1/Q235 composite plates were investigated.Results show that the quality of interface bonding is excellent,presenting typical waveform morphology with an average interface shear strength above 330 MPa and an average impact toughness exceeding 81 J.All samples can be bent to 180°without significant delamination or cracking defects.
基金Natural Science Foundation of Shanxi Province(202203021221149)Key Research and Development Program of Shanxi Province(202302010101006,202202150401016)+1 种基金Scientific Research Start-up Fund for the Introduction of Talents in Shanxi Institute of Electronic Science and Technology(2023RKJ021)Key R&D Program of Linfen City(2334)。
文摘High-performance pure nickel N6/steel 45#composite plate(N6/45#)was prepared using explosive welding technique.The microstructure of the interface and nearby regions was characterized and analyzed by optical microscope,scanning electron microscope,electron backscatter diffraction,and mechanical property testing,and the microstructural features and mechanical properties of the explosive welding interface were explored.The results show that along the direction of explosive welding,the pure nickel N6/steel 45#composite plate interface gradually evolves from a flat bond to a typical wavy bond.The grains at the crests and troughs exhibit high heterogeneity,and the closer to the interface,the finer the grains.Recrystallization and low-stress deformation bands are formed at the bonding interface.Nanoindentation tests reveal that plastic deformation occurs in the interfacial bonding zone,and the nanohardness values in the crest regions are higher than that in the trough regions.The tensile strength of the N6/45#interface is 599.8 MPa,with an average shear strength of 326.3 MPa.No separation phenomenon is observed between N6 and 45#after the bending test.
基金supported by the Key Research and Development Program of Hubei Province(No.2021BAA057)the National Natural Science Foundation of China(Nos.U20A20279,12174296 and 12102310)+5 种基金the Major Program(JD)of Hubei Province(No.2023BAA019-5)the Natural Science Foundation of Hubei Province(No.2022CFB474)the Science and Technology Program of Guangxi Province(No.AA22068080)the Taishan Industry Leading Talent Project(No.2020007)the Leading Innovation and Pioneering Team of Zhejiang Province(2021R01020)the 111 Project(No.D18018).
文摘The low-density medium-Mn steel is widely studied and applied in the automobile and construction machinery due to the low costs and high strength-ductility.Adding lightweight elements,such as aluminum,is considered an efficient way to reduce the density of the steels.A novel 5Al-5Mn-1.5Si-0.3C(wt%)low-density and high-strengthδ-ferrite/martensite(δ-F/M)steel was designed in this study.The study indicated that the designed steel annealed at 1080℃was characterized by an excellent combination of tensile strength of 1246 MPa and density of 7.24 g/cm^(3).Microscopic characterization shows that the higher prior-austenite volume fraction(i.e.,martensite plus retained austenite)significantly increases the tensile strength,and the strip-like martensite and retained austenite(M&RA)mixture benefits elongation.High martensite fraction owns higher origin geometrically necessary dislocations,contributing to better work-hardening behaviors.Concurrently,the synergistic presence of M&RA mixtures’volume fraction and morphology enhances their capability to absorb stress and obstruct crack propagation,significantly improving mechanical performance.The extended strength formula,accounting for the contribution of the M&RA mixture,is consistent with the quantitative agreement observed in experimental results.These insights provide a valuable technological reference for the knowledge-based design and prediction of the mechanical properties of low-density and high-strength steel.
基金the support and encouragement of the Key Projects of the Ministry of Industry and Information Technology of China(TC220A04W-3,188)。
文摘It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the macro-and micro-mixing affect the reactor performance was still controversial in publications.In this work,a cold-flow LDPE autoclave with multi-feedings was scaled down(1/2)from an industrial reactor and built to systematically investigate the macro-and micro-mixing characteristics of fluid by experiments.Furthermore,the effects of macro-and micro-mixing on the polymerization were comprehensively analyzed.The results showed that according to the delay time t_(d) and macro-mixing times tM calculated from residence time distribution(RTD)curves,the macro-mixing states are significantly different at various axial positions(h/H),especially at lower agitation Reynolds number Re.But with the increase of Re,since the circulation flow in the reactor is strengthened,the t_(d) for each feed gradually decreases to 0,and the t_(M) at different axial positions tend to be identical.For micro-mixing,the qualities of micro-mixing at different axial positions are similar,and the average micro-mixing time t_(m) in the reactor decreases exponentially with the increase of Re.Moreover,a fitting model was established.Through the comparison of the characteristic times of macro-mixing(t_(d),t_(M)),micro-mixing(t_(m))and elementary reactions within the industrial range of Re,it can be concluded that the properties of LDPE products are dominated by the macro-mixing behavior,and the consumption of initiators is affected by both the macro-and micro-mixing behaviors.This conclusion is of great significance for the design,optimization and operation of LDPE reactors.
基金supports from National Natural Science Foundation of China(No.U20A20270)China Postdoctoral Science Foundation(No.2022M722486).
文摘The effects of austenite grain size on the deformed microstructure and mechanical properties of an Fe-20Mn-6Al-0.6C-0.15Si(wt.%)low-density steel were investigated.The microstructure of the experimental steel after solution treatment was single austenitic phase.The austenite grain size increased with solution temperature and time.A model was established to show the relationship between temperature,time and austenite grain size for the experimental steel.In addition,as the solution temperature increased,the strength decreased,while the elongation first increased and then decreased.This decrease in elongation after solution treatment at 1100℃ for 90 min is contributed to the over-coarse austenite grains.However,after solution treatment at 900℃ for 90 min,the strength-elongation product reached the highest value of 44.4 GPa%.As the austenite grain size increased,the intensity of<111>//tensile direction fiber decreased.This was accompanied by a decrease in dislocation density,resulting in a lower fraction of low-angle grain boundaries and a lower work hardening rate.Therefore,the austenite grain size has a critical influence on the mechanical properties of the low-density steels.Coarser grains lead to a lower yield strength due to the Hall-Petch effect and a lower tensile strength because of lower dislocation strengthening.
基金financially supported by Korea Institute for Advancement of Technology(KIAT)grant funded by the Ko-rea Government(MOTIE)(HRD Program for Industrial Innova-tion)(P0023676)the National Research Foundation of Ko-rea(NRF)grant funded by the Korea government(MSIT)(NRF-2022R1A5A1030054,RS-2023-00281508,NRF-RS-2024-00345498).
文摘Martensitic-based microstructures in low-density steels offer high strength and improved specific strength,combined with the lightweight effect of aluminum(Al).However,while Al effectively reduces density,it simultaneously promotes the formation of coarse ferrite and expands the two-phase(α+γ)intercritical temperature range.Thus,increasing the Al content for higher weight reduction inevitably leads to ferrite formation and impedes further strengthening.To achieve both high strength and duc-tility while incorporating ferrite,it is crucial to elucidate the effects of ferrite fraction,size,and dis-tribution on mechanical properties and deformation behavior,particularly in relation to phase interac-tions.In this study,three model steels were developed through controlled annealing temperatures,pro-ducing distinct triplex microstructures comprising ferrite,martensite,and retained austenite(RA).The role of each phase in strain partitioning was investigated using ex-situ microscopic digital image cor-relation and electron back-scattered diffraction analysis.Key findings reveal that the martensitic matrix ensures an ultrahigh strength level(1758 MPa),while a moderate fraction(∼17%)and homogeneous dis-tribution of intercritical-ferrite(IC-ferrite)enable sustainable strain-hardening behavior by delaying the transformation-induced plasticity(TRIP)effect.Strain partitioning into IC-ferrite reduces local strains in the martensitic matrix,preventing early exhaustion of the TRIP effect and facilitating ductile fracture behavior.This strategy leverages the presence of ferrite,offering significant advantages for applications requiring both ultrahigh strength and ductility.
文摘BACKGROUND Esophageal cancer(EC)is one of the most common malignancies worldwide,and lymph node(LN)metastasis remains one of the leading causes of EC recurrence.Metabolic disorders critically affect cancer progression,and lipid levels are closely associated with the occurrence of EC and several other tumor types.This study analyzed pretreatment lipid levels to determine their association with LN metastasis.AIM To dissect the possible mechanisms underlying LN metastasis and clarify the prognostic role of lipid profiles in EC.METHODS Serum lipid levels and clinicopathological information were retrospectively collected from 294 patients,and risk factors for LN metastasis were confirmed using a logistic regression model.Latent factors were explored using information from publicly accessible databases and immunofluorescence and immunohistochemical staining techniques.RESULTS High serum levels of low-density lipoprotein(LDL)cholesterol promote LN metastasis in EC,while high-density lipoprotein cholesterol has the opposite role.Information of a public database revealed that LDL receptors LRP5 and LRP6 are highly expressed in ECs,and LRP6 overexpression positively correlated with the infiltration of B lymphocytes and a poor prognosis.Immunofluorescence and immunohistochemical staining revealed that the expression of LRP6 and infiltrated B lymphocytes in patients with≥1 regional LN metastasis,containing N1-3(N+group)were significantly higher than those in the N0 group.LRP6 was also highly expressed in the B lymphocytes of the N+group.There was no difference in CXCL13 expression between the N+and N0 groups.However,CXCR5 expression was significantly higher in the N0 group than in the N+group.CONCLUSION High serum LDL levels can promote LN metastasis in EC,and the mechanisms may be related to LRP6 expression and the infiltration of B lymphocytes.
