A low power 433 MHz CMOS （complementary metal- oxide-semiconductor transistor） low noise amplifier（LNA）, used for an ISM （ industrial-scientific-medical ） receiver, is implemented in a 0. 18 μm SMIC mixed-signa...A low power 433 MHz CMOS （complementary metal- oxide-semiconductor transistor） low noise amplifier（LNA）, used for an ISM （ industrial-scientific-medical ） receiver, is implemented in a 0. 18 μm SMIC mixed-signal and RF （ radio frequency） CMOS process. The optimal noise performance of the CMOS LNA is achieved by adjusting the source degeneration inductance and by inserting an appropriate capacitance in parallel with the input transistor of the LNA. The measured results show that at 431 MHz the LNA has a noise figure of 2.4 dB. The S21 is equal to 16 dB, S11 = -11 dB, S22 = -9 dB, and the inverse isolation is 35 dB. The measured input 1-dB compression point （PtdB） and input third-order intermodulation product （IIP3）are - 13 dBm and -3 dBm, respectively. The chip area is 0. 55 mm × 1.2 mm and the DC power consumption is only 4 mW under a 1.8 V voltage supply.展开更多
Work on dynamic topology optimization of engineering structures for vibration suppression has mainly addressed the maximization of eigenfrequencies and gaps between consecutive eigenfrequencies of free vibration, mini...Work on dynamic topology optimization of engineering structures for vibration suppression has mainly addressed the maximization of eigenfrequencies and gaps between consecutive eigenfrequencies of free vibration, minimization of the dynamic compliance subject to forced vibration, and minimization of the structural frequency response. A dynamic topology optimization method of bi-material plate structures is presented based on power flow analysis. Topology optimization problems formulated directly with the design objective of minimizing the power flow response are dealt with. In comparison to the displacement or velocity response, the power flow response takes not only the amplitude of force and velocity into account, but also the phase relationship of the two vector quantities. The complex expression of power flow response is derived based on time-harmonic external mechanical loading and Rayleigh damping. The mathematical formulation of topology optimization is established based on power flow response and bi-material solid isotropic material with penalization(SIMP) model. Computational optimization procedure is developed by using adjoint design sensitivity analysis and the method of moving asymptotes(MMA). Several numerical examples are presented for bi-material plate structures with different loading frequencies, which verify the feasibility and effectiveness of this method. Additionally, optimum results between topological design of minimum power flow response and minimum dynamic compliance are compared, showing that the present method has strong adaptability for structural dynamic topology optimization problems. The proposed research provides a more accurate and effective approach for dynamic topology optimization of vibrating structures.展开更多
Considering the uncertainty of grid connection of electric vehicle charging stations and the uncertainty of new energy and residential electricity load,a spatio-temporal decoupling strategy of dynamic reactive power o...Considering the uncertainty of grid connection of electric vehicle charging stations and the uncertainty of new energy and residential electricity load,a spatio-temporal decoupling strategy of dynamic reactive power optimization based on clustering-local relaxation-correction is proposed.Firstly,the k-medoids clustering algorithm is used to divide the reduced power scene into periods.Then,the discrete variables and continuous variables are optimized in the same period of time.Finally,the number of input groups of parallel capacitor banks(CB)in multiple periods is fixed,and then the secondary static reactive power optimization correction is carried out by using the continuous reactive power output device based on the static reactive power compensation device(SVC),the new energy grid-connected inverter,and the electric vehicle charging station.According to the characteristics of the model,a hybrid optimization algorithm with a cross-feedback mechanism is used to solve different types of variables,and an improved artificial hummingbird algorithm based on tent chaotic mapping and adaptive mutation is proposed to improve the solution efficiency.The simulation results show that the proposed decoupling strategy can obtain satisfactory optimization resultswhile strictly guaranteeing the dynamic constraints of discrete variables,and the hybrid algorithm can effectively solve the mixed integer nonlinear optimization problem.展开更多
In covert communications,joint jammer selection and power optimization are important to improve performance.However,existing schemes usually assume a warden with a known location and perfect Channel State Information(...In covert communications,joint jammer selection and power optimization are important to improve performance.However,existing schemes usually assume a warden with a known location and perfect Channel State Information(CSI),which is difficult to achieve in practice.To be more practical,it is important to investigate covert communications against a warden with uncertain locations and imperfect CSI,which makes it difficult for legitimate transceivers to estimate the detection probability of the warden.First,the uncertainty caused by the unknown warden location must be removed,and the Optimal Detection Position(OPTDP)of the warden is derived which can provide the best detection performance(i.e.,the worst case for a covert communication).Then,to further avoid the impractical assumption of perfect CSI,the covert throughput is maximized using only the channel distribution information.Given this OPTDP based worst case for covert communications,the jammer selection,the jamming power,the transmission power,and the transmission rate are jointly optimized to maximize the covert throughput(OPTDP-JP).To solve this coupling problem,a Heuristic algorithm based on Maximum Distance Ratio(H-MAXDR)is proposed to provide a sub-optimal solution.First,according to the analysis of the covert throughput,the node with the maximum distance ratio(i.e.,the ratio of the distances from the jammer to the receiver and that to the warden)is selected as the friendly jammer(MAXDR).Then,the optimal transmission and jamming power can be derived,followed by the optimal transmission rate obtained via the bisection method.In numerical and simulation results,it is shown that although the location of the warden is unknown,by assuming the OPTDP of the warden,the proposed OPTDP-JP can always satisfy the covertness constraint.In addition,with an uncertain warden and imperfect CSI,the covert throughput provided by OPTDP-JP is 80%higher than the existing schemes when the covertness constraint is 0.9,showing the effectiveness of OPTDP-JP.展开更多
To address the issue of coordinated control of multiple hydrogen and battery storage units to suppress the grid-injected power deviation of wind farms,an online optimization strategy for Battery-hydrogen hybrid energy...To address the issue of coordinated control of multiple hydrogen and battery storage units to suppress the grid-injected power deviation of wind farms,an online optimization strategy for Battery-hydrogen hybrid energy storage systems based on measurement feedback is proposed.First,considering the high charge/discharge losses of hydrogen storage and the low energy density of battery storage,an operational optimization objective is established to enable adaptive energy adjustment in the Battery-hydrogen hybrid energy storage system.Next,an online optimization model minimizing the operational cost of the hybrid system is constructed to suppress grid-injected power deviations with satisfying the operational constraints of hydrogen storage and batteries.Finally,utilizing the online measurement of the energy states of hydrogen storage and batteries,an online optimization strategy based on measurement feedback is designed.Case study results show:before and after smoothing the fluctuations in wind power,the time when the power exceeded the upper and lower limits of the grid-injected power accounted for 24.1%and 1.45%of the total time,respectively,the proposed strategy can effectively keep the grid-injected power deviations of wind farms within the allowable range.Hydrogen storage and batteries respectively undertake long-term and short-term charge/discharge tasks,effectively reducing charge/discharge losses of the Battery-hydrogen hybrid energy storage systems and improving its operational efficiency.展开更多
This paper proposes an efficient method for optimal power flow solution （OPF） using particle swarm optimization （PSO） technique. The objective of the proposed method is to find the steady state operation point in ...This paper proposes an efficient method for optimal power flow solution （OPF） using particle swarm optimization （PSO） technique. The objective of the proposed method is to find the steady state operation point in a power system which minimizes the fuel cost, while maintaining an acceptable system performance in terms of limits on generator power, line flow limits and voltage limits. In order to improvise the performance of the conventional PSO （cPSO）, the fine tuning parameters- the inertia weight and acceleration coefficients are formulated in terms of global-local best values of the objective function. These global-local best inertia weight （GLBestlW） and global-local best acceleration coefficient （GLBestAC） are incorporated into PSO in order to compute the optimal power flow solution. The proposed method has been tested on the standard IEEE 30 bus test system to prove its efficacy. The results are compared with those obtained through cPSO. It is observed that the proposed algorithm is computationally faster, in terms of the number of load flows executed and provides better results than the conventional heuristic techniques.展开更多
Ensuring the reliability of power systems in microgrids is critical,particularly under contingency conditions that can disrupt power flow and system stability.This study investigates the application of Security-Constr...Ensuring the reliability of power systems in microgrids is critical,particularly under contingency conditions that can disrupt power flow and system stability.This study investigates the application of Security-Constrained Optimal Power Flow(SCOPF)using the Line Outage Distribution Factor(LODF)to enhance resilience in a renewable energy-integrated microgrid.The research examines a 30-bus system with 14 generators and an 8669 MW load demand,optimizing both single-objective and multi-objective scenarios.The single-objective opti-mization achieves a total generation cost of$47,738,while the multi-objective approach reduces costs to$47,614 and minimizes battery power output to 165.02 kW.Under contingency conditions,failures in transmission lines 1,22,and 35 lead to complete power loss in those lines,requiring a redistribution strategy.Implementing SCOPF mitigates these disruptions by adjusting power flows,ensuring no line exceeds its capacity.Specifically,in contingency 1,power in channel 4 is reduced from 59 to 32 kW,while overall load shedding is minimized to 0.278 MW.These results demonstrate the effectiveness of SCOPF in maintaining stability and reducing economic losses.Unlike prior studies,this work integrates LODF into SCOPF for large-scale microgrid applications,offering a computationally efficient contingency management framework that enhances grid resilience and supports renewable energy adoption.展开更多
Restructuring of power market not only introduces competition but also brings complexity which increases overloading of Transmission Lines(TL).To obviate this complexity,this paper aims to mitigate the overloading and...Restructuring of power market not only introduces competition but also brings complexity which increases overloading of Transmission Lines(TL).To obviate this complexity,this paper aims to mitigate the overloading and estimate the optimal location of Static Synchronous Compensator(STATCOM) by reducing congestion for a deregulated power system.The proposed method is based on the use of Locational Marginal Price(LMP) difference technique and congestion cost.LMPs are obtained as a by-product of Optimal Power Flow(OPF),whereas Congestion Cost(CC) is a function of difference in LMP and power flows.The effiectiveness of this approach is demonstrated by reducing the CC and solution space which can identify the TLs more suitable for placement of STATCOM.Importantly,total real power loss,reactive power loss and total CC are the three main objective functions in this optimization process.The process is implemented by developing an IEEE-69 bus test system which verifies and validates the effectiveness of proposed optimization technique.Additionally,a comparative analysis is enumerated by implementing two optimization techniques:Flower Pollination Algorithm(FPA) and Particle Swarm Optimization(PSO).The comparative analysis is sufficient to demonstrate the superiority of FPA technique over PSO technique in estimating an optimal placement of a STATCOM.The results from the load-flow analysis illustrate the reduction in CC,total real and reactive power loss using FPA technique compared to PSO technique.Overall,satisfactory results are obtained without using complex calculations which verify the effectiveness of optimization techniques.展开更多
The Sine and Wormhole Energy Whale Optimization Algorithm(SWEWOA)represents an advanced solution method for resolving Optimal Power Flow(OPF)problems in power systems equipped with Flexible AC Transmission System(FACT...The Sine and Wormhole Energy Whale Optimization Algorithm(SWEWOA)represents an advanced solution method for resolving Optimal Power Flow(OPF)problems in power systems equipped with Flexible AC Transmission System(FACTS)devices which include Thyristor-Controlled Series Compensator(TCSC),Thyristor-Controlled Phase Shifter(TCPS),and Static Var Compensator(SVC).SWEWOA expands Whale Optimization Algorithm(WOA)through the integration of sine and wormhole energy features thus improving exploration and exploitation capabilities for efficient convergence in complex non-linear OPF problems.A performance evaluation of SWEWOA takes place on the IEEE-30 bus test system through static and dynamic loading scenarios where it demonstrates better results than five contemporary algorithms:Adaptive Chaotic WOA(ACWOA),WOA,Chaotic WOA(CWOA),Sine Cosine Algorithm Differential Evolution(SCADE),and Hybrid Grey Wolf Optimization(HGWO).The research shows that SWEWOA delivers superior generation cost reduction than other algorithms by reaching a minimum of 0.9%better performance.SWEWOA demonstrates superior power loss performance by achieving(P_(loss,min))at the lowest level compared to all other tested algorithms which leads to better system energy efficiency.The dynamic loading performance of SWEWOA leads to a 4.38%reduction in gross costs which proves its capability to handle different operating conditions.The algorithm achieves top performance in Friedman Rank Test(FRT)assessments through multiple performance metrics which verifies its consistent reliability and strong stability during changing power demands.The repeated simulations show that SWEWOA generates mean costs(C_(gen,min))and mean power loss values(P_(loss,min))with small deviations which indicate its capability to maintain cost-effective solutions in each simulation run.SWEWOA demonstrates great potential as an advanced optimization solution for power system operations through the results presented in this study.展开更多
As a novel signaling technology,the power splitting receiver(PSR)simultaneously employs both the coherent and non-coherent signal processing.In order to improve its communication performance,an intelligent reflecting ...As a novel signaling technology,the power splitting receiver(PSR)simultaneously employs both the coherent and non-coherent signal processing.In order to improve its communication performance,an intelligent reflecting surface(IRS)is introduced into its signal propagation path.Consequently,an IRSaided PSR is concerned for a point-to-point(P2P)data link,where both the single-antenna and multiantenna deployments on the receiver are discussed.We aim at maximizing the capacity of the concerned P2P data-link by jointly optimizing the passive beamforming of IRS and the splitting ratio of PSR,either in single-antenna or multi-antenna case.However,owing to the coupling of multiple variables,the optimization problems are non-convex and challenging,especially in the later multi-antenna case.The proposed alternating-approximating algorithm(A-A),aided by semi-definite relaxation(SDR)and successive convex approximation(SCA)methods,etc.,successfully overcomes these challenges.We compare the IRS-aided PSR system that optimized by our proposed algorithm to the systems without IRS or PSR,and the systems without joint optimization.The simulation results show that our proposal has a better performance.展开更多
As an emerging memory device,memristor shows great potential in neuromorphic computing applications due to its advantage of low power consumption.This review paper focuses on the application of low-power-based memrist...As an emerging memory device,memristor shows great potential in neuromorphic computing applications due to its advantage of low power consumption.This review paper focuses on the application of low-power-based memristors in various aspects.The concept and structure of memristor devices are introduced.The selection of functional materials for low-power memristors is discussed,including ion transport materials,phase change materials,magnetoresistive materials,and ferroelectric materials.Two common types of memristor arrays,1T1R and 1S1R crossbar arrays are introduced,and physical diagrams of edge computing memristor chips are discussed in detail.Potential applications of low-power memristors in advanced multi-value storage,digital logic gates,and analogue neuromorphic computing are summarized.Furthermore,the future challenges and outlook of neuromorphic computing based on memristor are deeply discussed.展开更多
The construction of island power grids is a systematic engineering task.To ensure the safe operation of power grid systems,optimizing the line layout of island power grids is crucial.Especially in the current context ...The construction of island power grids is a systematic engineering task.To ensure the safe operation of power grid systems,optimizing the line layout of island power grids is crucial.Especially in the current context of large-scale distributed renewable energy integration into the power grid,conventional island power grid line layouts can no longer meet actual demands.It is necessary to combine the operational characteristics of island power systems and historical load data to perform load forecasting,thereby generating power grid line layout paths.This article focuses on large-scale distributed renewable energy integration,summarizing optimization strategies for island power grid line layouts,and providing a solid guarantee for the safe and stable operation of island power systems.展开更多
Underwater charging stations allow Autonomous Underwater Vehicles(AUVs)to recharge batteries,extending missions and reducing surface support.However,efficient wireless power transfer requires overcoming alignment chal...Underwater charging stations allow Autonomous Underwater Vehicles(AUVs)to recharge batteries,extending missions and reducing surface support.However,efficient wireless power transfer requires overcoming alignment challenges and environmental variations in conductive seawater.This paper employs Particle Swarm Optimization(PSO)to design coupling coils specifically applied for underwater wireless charging station systems.The establishment of underwater charging stations enables Autonomous Underwater Vehicles(AUVs)to recharge batteries underwater,extending mission duration and reducing reliance on surface-based resupply operations.The proposed charging system is designed to address the unique challenges of the underwater environment,such as alignment disruptions and performance degradation caused by seawater conductivity and environmental fluctuations.Given these distinctive underwater conditions,this study explores coupling coil design comprehensively.COMSOL Multiphysics and MATLAB software were integrated to develop an automated coil evaluation platform,effectively assessing coil coupling under varying misalignment conditions.PSO was employed to optimize coil inner diameters,simulating coupling performance across different misalignment scenarios to achieve high misalignment tolerance.The optimized coils were subsequently implemented in a full-bridge series-series resonant converter and compared with control group coils.Results confirmed the PSO-optimized coils enhanced misalignment resistance,exhibiting a variation of coupling coefficient as low as 4.26%,while the control group coils have a variation of 10.34%.In addition,compared to control group coils,PSO-optimized coils achieved an average efficiency of 71%in air and 67%in seawater,outperforming the control group coils at 66%and 60%,respectively.These findings demonstrate the effectiveness of the proposed PSO-based coil design in improving underwater wireless power transfer reliability and efficiency.展开更多
The intermittency and volatility of wind and photovoltaic power generation exacerbate issues such as wind and solar curtailment,hindering the efficient utilization of renewable energy and the low-carbon development of...The intermittency and volatility of wind and photovoltaic power generation exacerbate issues such as wind and solar curtailment,hindering the efficient utilization of renewable energy and the low-carbon development of energy systems.To enhance the consumption capacity of green power,the green power system consumption optimization scheduling model(GPS-COSM)is proposed,which comprehensively integrates green power system,electric boiler,combined heat and power unit,thermal energy storage,and electrical energy storage.The optimization objectives are to minimize operating cost,minimize carbon emission,and maximize the consumption of wind and solar curtailment.The multi-objective particle swarm optimization algorithm is employed to solve the model,and a fuzzy membership function is introduced to evaluate the satisfaction level of the Pareto optimal solution set,thereby selecting the optimal compromise solution to achieve a dynamic balance among economic efficiency,environmental friendliness,and energy utilization efficiency.Three typical operating modes are designed for comparative analysis.The results demonstrate that the mode involving the coordinated operation of electric boiler,thermal energy storage,and electrical energy storage performs the best in terms of economic efficiency,environmental friendliness,and renewable energy utilization efficiency,achieving the wind and solar curtailment consumption rate of 99.58%.The application of electric boiler significantly enhances the direct accommodation capacity of the green power system.Thermal energy storage optimizes intertemporal regulation,while electrical energy storage strengthens the system’s dynamic regulation capability.The coordinated optimization of multiple devices significantly reduces reliance on fossil fuels.展开更多
Given the power system balancing challenges induced by high-penetration renewable energy integration,this study systematically reviews international balancing mechanism practices and conducts an in-depth deconstructio...Given the power system balancing challenges induced by high-penetration renewable energy integration,this study systematically reviews international balancing mechanism practices and conducts an in-depth deconstruction of Germany’s balancing group mechanism(BGM).Building on this foundation,this research pioneers the integration of virtual power plants(VPPs)with the BGM in the Chinese context to overcome the limitations of traditional single-entity regulation models in flexibility provision and economic efficiency.A balancing responsibility framework centered on VPPs is innovatively proposed and a regional multi-entity collaboration and bi-level responsibility transfer architecture is constructed.This architecture enables cross-layer coordinated optimization of regional system costs and VPP revenues.The upper layer minimizes regional operational costs,whereas the lower layer enhances the operational revenues of VPPs through dynamic gaming between deviation regulation service income and penalty costs.Compared with traditional centralized regulation models,the proposed method reduces system operational costs by 29.1%in typical regional cases and increases VPP revenues by 24.9%.These results validate its dual optimization of system economics and participant incentives through market mechanisms,providing a replicable theoretical paradigm and practical pathway for designing balancing mechanisms in new power systems.展开更多
The frequency regulation reserve setting of wind-PV-storage power stations is crucial.However,the existing grid codes set up the station reserve in a static manner,where the synchronous generator characteristics and f...The frequency regulation reserve setting of wind-PV-storage power stations is crucial.However,the existing grid codes set up the station reserve in a static manner,where the synchronous generator characteristics and frequency-step disturbance scenario are considered.Thus,the advantages of flexible regulation of renewable generations are wasted,resulting in excessive curtailment of wind and solar resources.In this study,a method for optimizing the frequency regulation reserve of wind PV storage power stations was developed.Moreover,a station frequency regulation model was constructed,considering the field dynamic response and the coupling between the station and system frequency dynamics.Furthermore,a method for the online evaluation of the station frequency regulation was proposed based on the benchmark governor fitting.This method helps in overcoming the capacity-based reserve static setting.Finally,an optimization model was developed,along with the proposal of the linearized solving algorithm.The field data from the JH4#station in China’s MX power grid was considered for validation.The proposed method achieves a 24.77%increase in the station income while ensuring the system frequency stability when compared with the grid code-based method.展开更多
Steam power systems(SPSs)in industrial parks are the typical utility systems for heat and electricity supply.In SPSs,electricity is generated by steam turbines,and steam is generally produced and supplied at multiple ...Steam power systems(SPSs)in industrial parks are the typical utility systems for heat and electricity supply.In SPSs,electricity is generated by steam turbines,and steam is generally produced and supplied at multiple levels to serve the heat demands of consumers with different temperature grades,so that energy is utilized in cascade.While a large number of steam levels enhances energy utilization efficiency,it also tends to cause a complex steam pipeline network in the industrial park.In practice,a moderate number of steam levels is always adopted in SPSs,leading to temperature mismatches between heat supply and demand for some consumers.This study proposes a distributed steam turbine system(DSTS)consisting of main steam turbines on the energy supply side and auxiliary steam turbines on the energy consumption side,aiming to balance the heat production costs,the distance-related costs,and the electricity generation of SPSs in industrial parks.A mixed-integer nonlinear programming model is established for the optimization of SPSs,with the objective of minimizing the total annual cost(TAC).The optimal number of steam levels and the optimal configuration of DSTS for an industrial park can be determined by solving the model.A case study demonstrates that the TAC of the SPS is reduced by 220.6×10^(3)USD(2.21%)through the arrangement of auxiliary steam turbines.The sub-optimal number of steam levels and a non-optimal operating condition slightly increase the TAC by 0.46%and 0.28%,respectively.The sensitivity analysis indicates that the optimal number of steam levels tends to decrease from 3 to 2 as electricity price declines.展开更多
The rapid development of artificial intelligence(AI)technology,particularly breakthroughs in branches such as deep learning,reinforcement learning,and federated learning,has provided powerful technical tools for addre...The rapid development of artificial intelligence(AI)technology,particularly breakthroughs in branches such as deep learning,reinforcement learning,and federated learning,has provided powerful technical tools for addressing these core bottlenecks.This paper provides a systematic review of the research background,technological evolution,core systems,key challenges,and future directions of AI technology in the field of distributed photovoltaic power generation system optimization.At the same time,this paper analyzes the current technical bottlenecks and cutting-edge response strategies.Finally,it explores fusion innovation directions such as quantum-classical hybrid algorithms and neural symbolic systems,as well as business model expansion paths such as carbon finance integration and community energy autonomy.展开更多
An optimizing method for designing the wireless power receiving coil(RC)is proposed in this paper to address issues such as insufficient and fluctuating power supply in the near-infrared capsule robot.An elec-tromagne...An optimizing method for designing the wireless power receiving coil(RC)is proposed in this paper to address issues such as insufficient and fluctuating power supply in the near-infrared capsule robot.An elec-tromagnetic and circuit analysis is conducted to establish the magnetic induction intensity and equivalent circuit models for the wireless power transmission system.Combining these models involves using the number of layers in each dimension as the optimization variable.Constraints are imposed based on the normalized standard deviation of the receiving-end load power and spatial dimensions.At the same time,the optimization objective aims to maximize the average power of the receiving-end load.This process leads to formulating an optimization model for the RC.Finally,three-dimensional RCs with three different sets of parameters are wound,and the receiving-end load power of these coils is experimentally tested under various drive currents.The experimental values of the receiving-end load power exhibit a consistent trend with theoretical values,with experimental values consistently lower than theoretical values.The optimized coil parameters are determined by conducting comparative exper-iments,with a theoretical value of 4.6%for the normalized standard deviation of the receiving-end load power and an average experimental value of 9.6%.The study addressed the power supply issue of near-infrared capsule robots,which is important for early diagnosing and treating gastrointestinal diseases.展开更多
基金The National Natural Science Foundation of China (No.60772008)the Key Science and Technology Program of Zhejiang Province(No.G2006C13024)
文摘A low power 433 MHz CMOS （complementary metal- oxide-semiconductor transistor） low noise amplifier（LNA）, used for an ISM （ industrial-scientific-medical ） receiver, is implemented in a 0. 18 μm SMIC mixed-signal and RF （ radio frequency） CMOS process. The optimal noise performance of the CMOS LNA is achieved by adjusting the source degeneration inductance and by inserting an appropriate capacitance in parallel with the input transistor of the LNA. The measured results show that at 431 MHz the LNA has a noise figure of 2.4 dB. The S21 is equal to 16 dB, S11 = -11 dB, S22 = -9 dB, and the inverse isolation is 35 dB. The measured input 1-dB compression point （PtdB） and input third-order intermodulation product （IIP3）are - 13 dBm and -3 dBm, respectively. The chip area is 0. 55 mm × 1.2 mm and the DC power consumption is only 4 mW under a 1.8 V voltage supply.
基金supported by China Armament Pre-research Foundation(Grant No. 51318010402)UK Engineering and Physical Science Research Council (EPSRC), and China Scholarship Council (Grant No.2010611054)
文摘Work on dynamic topology optimization of engineering structures for vibration suppression has mainly addressed the maximization of eigenfrequencies and gaps between consecutive eigenfrequencies of free vibration, minimization of the dynamic compliance subject to forced vibration, and minimization of the structural frequency response. A dynamic topology optimization method of bi-material plate structures is presented based on power flow analysis. Topology optimization problems formulated directly with the design objective of minimizing the power flow response are dealt with. In comparison to the displacement or velocity response, the power flow response takes not only the amplitude of force and velocity into account, but also the phase relationship of the two vector quantities. The complex expression of power flow response is derived based on time-harmonic external mechanical loading and Rayleigh damping. The mathematical formulation of topology optimization is established based on power flow response and bi-material solid isotropic material with penalization(SIMP) model. Computational optimization procedure is developed by using adjoint design sensitivity analysis and the method of moving asymptotes(MMA). Several numerical examples are presented for bi-material plate structures with different loading frequencies, which verify the feasibility and effectiveness of this method. Additionally, optimum results between topological design of minimum power flow response and minimum dynamic compliance are compared, showing that the present method has strong adaptability for structural dynamic topology optimization problems. The proposed research provides a more accurate and effective approach for dynamic topology optimization of vibrating structures.
基金funded by the“Research and Application Project of Collaborative Optimization Control Technology for Distribution Station Area for High Proportion Distributed PV Consumption(4000-202318079A-1-1-ZN)”of the Headquarters of the State Grid Corporation.
文摘Considering the uncertainty of grid connection of electric vehicle charging stations and the uncertainty of new energy and residential electricity load,a spatio-temporal decoupling strategy of dynamic reactive power optimization based on clustering-local relaxation-correction is proposed.Firstly,the k-medoids clustering algorithm is used to divide the reduced power scene into periods.Then,the discrete variables and continuous variables are optimized in the same period of time.Finally,the number of input groups of parallel capacitor banks(CB)in multiple periods is fixed,and then the secondary static reactive power optimization correction is carried out by using the continuous reactive power output device based on the static reactive power compensation device(SVC),the new energy grid-connected inverter,and the electric vehicle charging station.According to the characteristics of the model,a hybrid optimization algorithm with a cross-feedback mechanism is used to solve different types of variables,and an improved artificial hummingbird algorithm based on tent chaotic mapping and adaptive mutation is proposed to improve the solution efficiency.The simulation results show that the proposed decoupling strategy can obtain satisfactory optimization resultswhile strictly guaranteeing the dynamic constraints of discrete variables,and the hybrid algorithm can effectively solve the mixed integer nonlinear optimization problem.
基金supported by the CAS Project for Young Scientists in Basic Research under Grant YSBR-035Jiangsu Provincial Key Research and Development Program under Grant BE2021013-2.
文摘In covert communications,joint jammer selection and power optimization are important to improve performance.However,existing schemes usually assume a warden with a known location and perfect Channel State Information(CSI),which is difficult to achieve in practice.To be more practical,it is important to investigate covert communications against a warden with uncertain locations and imperfect CSI,which makes it difficult for legitimate transceivers to estimate the detection probability of the warden.First,the uncertainty caused by the unknown warden location must be removed,and the Optimal Detection Position(OPTDP)of the warden is derived which can provide the best detection performance(i.e.,the worst case for a covert communication).Then,to further avoid the impractical assumption of perfect CSI,the covert throughput is maximized using only the channel distribution information.Given this OPTDP based worst case for covert communications,the jammer selection,the jamming power,the transmission power,and the transmission rate are jointly optimized to maximize the covert throughput(OPTDP-JP).To solve this coupling problem,a Heuristic algorithm based on Maximum Distance Ratio(H-MAXDR)is proposed to provide a sub-optimal solution.First,according to the analysis of the covert throughput,the node with the maximum distance ratio(i.e.,the ratio of the distances from the jammer to the receiver and that to the warden)is selected as the friendly jammer(MAXDR).Then,the optimal transmission and jamming power can be derived,followed by the optimal transmission rate obtained via the bisection method.In numerical and simulation results,it is shown that although the location of the warden is unknown,by assuming the OPTDP of the warden,the proposed OPTDP-JP can always satisfy the covertness constraint.In addition,with an uncertain warden and imperfect CSI,the covert throughput provided by OPTDP-JP is 80%higher than the existing schemes when the covertness constraint is 0.9,showing the effectiveness of OPTDP-JP.
基金Supported by State Grid Zhejiang Electric Power Co.,Ltd.Science and Technology Project Funding(No.B311DS230005).
文摘To address the issue of coordinated control of multiple hydrogen and battery storage units to suppress the grid-injected power deviation of wind farms,an online optimization strategy for Battery-hydrogen hybrid energy storage systems based on measurement feedback is proposed.First,considering the high charge/discharge losses of hydrogen storage and the low energy density of battery storage,an operational optimization objective is established to enable adaptive energy adjustment in the Battery-hydrogen hybrid energy storage system.Next,an online optimization model minimizing the operational cost of the hybrid system is constructed to suppress grid-injected power deviations with satisfying the operational constraints of hydrogen storage and batteries.Finally,utilizing the online measurement of the energy states of hydrogen storage and batteries,an online optimization strategy based on measurement feedback is designed.Case study results show:before and after smoothing the fluctuations in wind power,the time when the power exceeded the upper and lower limits of the grid-injected power accounted for 24.1%and 1.45%of the total time,respectively,the proposed strategy can effectively keep the grid-injected power deviations of wind farms within the allowable range.Hydrogen storage and batteries respectively undertake long-term and short-term charge/discharge tasks,effectively reducing charge/discharge losses of the Battery-hydrogen hybrid energy storage systems and improving its operational efficiency.
文摘This paper proposes an efficient method for optimal power flow solution （OPF） using particle swarm optimization （PSO） technique. The objective of the proposed method is to find the steady state operation point in a power system which minimizes the fuel cost, while maintaining an acceptable system performance in terms of limits on generator power, line flow limits and voltage limits. In order to improvise the performance of the conventional PSO （cPSO）, the fine tuning parameters- the inertia weight and acceleration coefficients are formulated in terms of global-local best values of the objective function. These global-local best inertia weight （GLBestlW） and global-local best acceleration coefficient （GLBestAC） are incorporated into PSO in order to compute the optimal power flow solution. The proposed method has been tested on the standard IEEE 30 bus test system to prove its efficacy. The results are compared with those obtained through cPSO. It is observed that the proposed algorithm is computationally faster, in terms of the number of load flows executed and provides better results than the conventional heuristic techniques.
文摘Ensuring the reliability of power systems in microgrids is critical,particularly under contingency conditions that can disrupt power flow and system stability.This study investigates the application of Security-Constrained Optimal Power Flow(SCOPF)using the Line Outage Distribution Factor(LODF)to enhance resilience in a renewable energy-integrated microgrid.The research examines a 30-bus system with 14 generators and an 8669 MW load demand,optimizing both single-objective and multi-objective scenarios.The single-objective opti-mization achieves a total generation cost of$47,738,while the multi-objective approach reduces costs to$47,614 and minimizes battery power output to 165.02 kW.Under contingency conditions,failures in transmission lines 1,22,and 35 lead to complete power loss in those lines,requiring a redistribution strategy.Implementing SCOPF mitigates these disruptions by adjusting power flows,ensuring no line exceeds its capacity.Specifically,in contingency 1,power in channel 4 is reduced from 59 to 32 kW,while overall load shedding is minimized to 0.278 MW.These results demonstrate the effectiveness of SCOPF in maintaining stability and reducing economic losses.Unlike prior studies,this work integrates LODF into SCOPF for large-scale microgrid applications,offering a computationally efficient contingency management framework that enhances grid resilience and supports renewable energy adoption.
文摘Restructuring of power market not only introduces competition but also brings complexity which increases overloading of Transmission Lines(TL).To obviate this complexity,this paper aims to mitigate the overloading and estimate the optimal location of Static Synchronous Compensator(STATCOM) by reducing congestion for a deregulated power system.The proposed method is based on the use of Locational Marginal Price(LMP) difference technique and congestion cost.LMPs are obtained as a by-product of Optimal Power Flow(OPF),whereas Congestion Cost(CC) is a function of difference in LMP and power flows.The effiectiveness of this approach is demonstrated by reducing the CC and solution space which can identify the TLs more suitable for placement of STATCOM.Importantly,total real power loss,reactive power loss and total CC are the three main objective functions in this optimization process.The process is implemented by developing an IEEE-69 bus test system which verifies and validates the effectiveness of proposed optimization technique.Additionally,a comparative analysis is enumerated by implementing two optimization techniques:Flower Pollination Algorithm(FPA) and Particle Swarm Optimization(PSO).The comparative analysis is sufficient to demonstrate the superiority of FPA technique over PSO technique in estimating an optimal placement of a STATCOM.The results from the load-flow analysis illustrate the reduction in CC,total real and reactive power loss using FPA technique compared to PSO technique.Overall,satisfactory results are obtained without using complex calculations which verify the effectiveness of optimization techniques.
文摘The Sine and Wormhole Energy Whale Optimization Algorithm(SWEWOA)represents an advanced solution method for resolving Optimal Power Flow(OPF)problems in power systems equipped with Flexible AC Transmission System(FACTS)devices which include Thyristor-Controlled Series Compensator(TCSC),Thyristor-Controlled Phase Shifter(TCPS),and Static Var Compensator(SVC).SWEWOA expands Whale Optimization Algorithm(WOA)through the integration of sine and wormhole energy features thus improving exploration and exploitation capabilities for efficient convergence in complex non-linear OPF problems.A performance evaluation of SWEWOA takes place on the IEEE-30 bus test system through static and dynamic loading scenarios where it demonstrates better results than five contemporary algorithms:Adaptive Chaotic WOA(ACWOA),WOA,Chaotic WOA(CWOA),Sine Cosine Algorithm Differential Evolution(SCADE),and Hybrid Grey Wolf Optimization(HGWO).The research shows that SWEWOA delivers superior generation cost reduction than other algorithms by reaching a minimum of 0.9%better performance.SWEWOA demonstrates superior power loss performance by achieving(P_(loss,min))at the lowest level compared to all other tested algorithms which leads to better system energy efficiency.The dynamic loading performance of SWEWOA leads to a 4.38%reduction in gross costs which proves its capability to handle different operating conditions.The algorithm achieves top performance in Friedman Rank Test(FRT)assessments through multiple performance metrics which verifies its consistent reliability and strong stability during changing power demands.The repeated simulations show that SWEWOA generates mean costs(C_(gen,min))and mean power loss values(P_(loss,min))with small deviations which indicate its capability to maintain cost-effective solutions in each simulation run.SWEWOA demonstrates great potential as an advanced optimization solution for power system operations through the results presented in this study.
基金supported by National Key R&D Program of China with Grant number 2019YFB1803400in part by Sichuan Science and Technology Program under Grant 2024NSFSC0472。
文摘As a novel signaling technology,the power splitting receiver(PSR)simultaneously employs both the coherent and non-coherent signal processing.In order to improve its communication performance,an intelligent reflecting surface(IRS)is introduced into its signal propagation path.Consequently,an IRSaided PSR is concerned for a point-to-point(P2P)data link,where both the single-antenna and multiantenna deployments on the receiver are discussed.We aim at maximizing the capacity of the concerned P2P data-link by jointly optimizing the passive beamforming of IRS and the splitting ratio of PSR,either in single-antenna or multi-antenna case.However,owing to the coupling of multiple variables,the optimization problems are non-convex and challenging,especially in the later multi-antenna case.The proposed alternating-approximating algorithm(A-A),aided by semi-definite relaxation(SDR)and successive convex approximation(SCA)methods,etc.,successfully overcomes these challenges.We compare the IRS-aided PSR system that optimized by our proposed algorithm to the systems without IRS or PSR,and the systems without joint optimization.The simulation results show that our proposal has a better performance.
基金supported by the NSFC(12474071)Natural Science Foundation of Shandong Province(ZR2024YQ051)+5 种基金Open Research Fund of State Key Laboratory of Materials for Integrated Circuits(SKLJC-K2024-12)the Shanghai Sailing Program(23YF1402200,23YF1402400)Funded by Basic Research Program of Jiangsu(BK20240424)Taishan Scholar Foundation of Shandong Province(tsqn202408006)Young Talent of Lifting engineering for Science and Technology in Shandong,China(SDAST2024QTB002)the Qilu Young Scholar Program of Shandong University.
文摘As an emerging memory device,memristor shows great potential in neuromorphic computing applications due to its advantage of low power consumption.This review paper focuses on the application of low-power-based memristors in various aspects.The concept and structure of memristor devices are introduced.The selection of functional materials for low-power memristors is discussed,including ion transport materials,phase change materials,magnetoresistive materials,and ferroelectric materials.Two common types of memristor arrays,1T1R and 1S1R crossbar arrays are introduced,and physical diagrams of edge computing memristor chips are discussed in detail.Potential applications of low-power memristors in advanced multi-value storage,digital logic gates,and analogue neuromorphic computing are summarized.Furthermore,the future challenges and outlook of neuromorphic computing based on memristor are deeply discussed.
文摘The construction of island power grids is a systematic engineering task.To ensure the safe operation of power grid systems,optimizing the line layout of island power grids is crucial.Especially in the current context of large-scale distributed renewable energy integration into the power grid,conventional island power grid line layouts can no longer meet actual demands.It is necessary to combine the operational characteristics of island power systems and historical load data to perform load forecasting,thereby generating power grid line layout paths.This article focuses on large-scale distributed renewable energy integration,summarizing optimization strategies for island power grid line layouts,and providing a solid guarantee for the safe and stable operation of island power systems.
基金supported by the National Science and Technology Council(NSTC),Taiwan[Project code MOST 110-2222-E-019-005-MY3].
文摘Underwater charging stations allow Autonomous Underwater Vehicles(AUVs)to recharge batteries,extending missions and reducing surface support.However,efficient wireless power transfer requires overcoming alignment challenges and environmental variations in conductive seawater.This paper employs Particle Swarm Optimization(PSO)to design coupling coils specifically applied for underwater wireless charging station systems.The establishment of underwater charging stations enables Autonomous Underwater Vehicles(AUVs)to recharge batteries underwater,extending mission duration and reducing reliance on surface-based resupply operations.The proposed charging system is designed to address the unique challenges of the underwater environment,such as alignment disruptions and performance degradation caused by seawater conductivity and environmental fluctuations.Given these distinctive underwater conditions,this study explores coupling coil design comprehensively.COMSOL Multiphysics and MATLAB software were integrated to develop an automated coil evaluation platform,effectively assessing coil coupling under varying misalignment conditions.PSO was employed to optimize coil inner diameters,simulating coupling performance across different misalignment scenarios to achieve high misalignment tolerance.The optimized coils were subsequently implemented in a full-bridge series-series resonant converter and compared with control group coils.Results confirmed the PSO-optimized coils enhanced misalignment resistance,exhibiting a variation of coupling coefficient as low as 4.26%,while the control group coils have a variation of 10.34%.In addition,compared to control group coils,PSO-optimized coils achieved an average efficiency of 71%in air and 67%in seawater,outperforming the control group coils at 66%and 60%,respectively.These findings demonstrate the effectiveness of the proposed PSO-based coil design in improving underwater wireless power transfer reliability and efficiency.
基金funded by the National Key Research and Development Program of China(2024YFE0106800)Natural Science Foundation of Shandong Province(ZR2021ME199).
文摘The intermittency and volatility of wind and photovoltaic power generation exacerbate issues such as wind and solar curtailment,hindering the efficient utilization of renewable energy and the low-carbon development of energy systems.To enhance the consumption capacity of green power,the green power system consumption optimization scheduling model(GPS-COSM)is proposed,which comprehensively integrates green power system,electric boiler,combined heat and power unit,thermal energy storage,and electrical energy storage.The optimization objectives are to minimize operating cost,minimize carbon emission,and maximize the consumption of wind and solar curtailment.The multi-objective particle swarm optimization algorithm is employed to solve the model,and a fuzzy membership function is introduced to evaluate the satisfaction level of the Pareto optimal solution set,thereby selecting the optimal compromise solution to achieve a dynamic balance among economic efficiency,environmental friendliness,and energy utilization efficiency.Three typical operating modes are designed for comparative analysis.The results demonstrate that the mode involving the coordinated operation of electric boiler,thermal energy storage,and electrical energy storage performs the best in terms of economic efficiency,environmental friendliness,and renewable energy utilization efficiency,achieving the wind and solar curtailment consumption rate of 99.58%.The application of electric boiler significantly enhances the direct accommodation capacity of the green power system.Thermal energy storage optimizes intertemporal regulation,while electrical energy storage strengthens the system’s dynamic regulation capability.The coordinated optimization of multiple devices significantly reduces reliance on fossil fuels.
基金supported by the National Natural Science Foundation of China(no.72471087)Beijing Nova Program(no.20250484853)+1 种基金Beijing Natural Science Foundation(no.9242015)National Social Science Foundation of China(no.24&ZD111).
文摘Given the power system balancing challenges induced by high-penetration renewable energy integration,this study systematically reviews international balancing mechanism practices and conducts an in-depth deconstruction of Germany’s balancing group mechanism(BGM).Building on this foundation,this research pioneers the integration of virtual power plants(VPPs)with the BGM in the Chinese context to overcome the limitations of traditional single-entity regulation models in flexibility provision and economic efficiency.A balancing responsibility framework centered on VPPs is innovatively proposed and a regional multi-entity collaboration and bi-level responsibility transfer architecture is constructed.This architecture enables cross-layer coordinated optimization of regional system costs and VPP revenues.The upper layer minimizes regional operational costs,whereas the lower layer enhances the operational revenues of VPPs through dynamic gaming between deviation regulation service income and penalty costs.Compared with traditional centralized regulation models,the proposed method reduces system operational costs by 29.1%in typical regional cases and increases VPP revenues by 24.9%.These results validate its dual optimization of system economics and participant incentives through market mechanisms,providing a replicable theoretical paradigm and practical pathway for designing balancing mechanisms in new power systems.
基金supported by the Scientific Research Project of China Three Gorges Group Co.LTD(Contract Number:202103368).
文摘The frequency regulation reserve setting of wind-PV-storage power stations is crucial.However,the existing grid codes set up the station reserve in a static manner,where the synchronous generator characteristics and frequency-step disturbance scenario are considered.Thus,the advantages of flexible regulation of renewable generations are wasted,resulting in excessive curtailment of wind and solar resources.In this study,a method for optimizing the frequency regulation reserve of wind PV storage power stations was developed.Moreover,a station frequency regulation model was constructed,considering the field dynamic response and the coupling between the station and system frequency dynamics.Furthermore,a method for the online evaluation of the station frequency regulation was proposed based on the benchmark governor fitting.This method helps in overcoming the capacity-based reserve static setting.Finally,an optimization model was developed,along with the proposal of the linearized solving algorithm.The field data from the JH4#station in China’s MX power grid was considered for validation.The proposed method achieves a 24.77%increase in the station income while ensuring the system frequency stability when compared with the grid code-based method.
基金Financial support from the National Natural Science Foundation of China under Grant(22393954 and 22078358)is gratefully acknowledged.
文摘Steam power systems(SPSs)in industrial parks are the typical utility systems for heat and electricity supply.In SPSs,electricity is generated by steam turbines,and steam is generally produced and supplied at multiple levels to serve the heat demands of consumers with different temperature grades,so that energy is utilized in cascade.While a large number of steam levels enhances energy utilization efficiency,it also tends to cause a complex steam pipeline network in the industrial park.In practice,a moderate number of steam levels is always adopted in SPSs,leading to temperature mismatches between heat supply and demand for some consumers.This study proposes a distributed steam turbine system(DSTS)consisting of main steam turbines on the energy supply side and auxiliary steam turbines on the energy consumption side,aiming to balance the heat production costs,the distance-related costs,and the electricity generation of SPSs in industrial parks.A mixed-integer nonlinear programming model is established for the optimization of SPSs,with the objective of minimizing the total annual cost(TAC).The optimal number of steam levels and the optimal configuration of DSTS for an industrial park can be determined by solving the model.A case study demonstrates that the TAC of the SPS is reduced by 220.6×10^(3)USD(2.21%)through the arrangement of auxiliary steam turbines.The sub-optimal number of steam levels and a non-optimal operating condition slightly increase the TAC by 0.46%and 0.28%,respectively.The sensitivity analysis indicates that the optimal number of steam levels tends to decrease from 3 to 2 as electricity price declines.
文摘The rapid development of artificial intelligence(AI)technology,particularly breakthroughs in branches such as deep learning,reinforcement learning,and federated learning,has provided powerful technical tools for addressing these core bottlenecks.This paper provides a systematic review of the research background,technological evolution,core systems,key challenges,and future directions of AI technology in the field of distributed photovoltaic power generation system optimization.At the same time,this paper analyzes the current technical bottlenecks and cutting-edge response strategies.Finally,it explores fusion innovation directions such as quantum-classical hybrid algorithms and neural symbolic systems,as well as business model expansion paths such as carbon finance integration and community energy autonomy.
基金the Project of the Science and Technology Commission of Shanghai Municipality(No.20142201300)the National Facility for Translational Medicine(Shanghai)Open Project Foundation(No.TMSK-2021-302)the China Postdoctoral Science Foundation(No.2023M732267)。
文摘An optimizing method for designing the wireless power receiving coil(RC)is proposed in this paper to address issues such as insufficient and fluctuating power supply in the near-infrared capsule robot.An elec-tromagnetic and circuit analysis is conducted to establish the magnetic induction intensity and equivalent circuit models for the wireless power transmission system.Combining these models involves using the number of layers in each dimension as the optimization variable.Constraints are imposed based on the normalized standard deviation of the receiving-end load power and spatial dimensions.At the same time,the optimization objective aims to maximize the average power of the receiving-end load.This process leads to formulating an optimization model for the RC.Finally,three-dimensional RCs with three different sets of parameters are wound,and the receiving-end load power of these coils is experimentally tested under various drive currents.The experimental values of the receiving-end load power exhibit a consistent trend with theoretical values,with experimental values consistently lower than theoretical values.The optimized coil parameters are determined by conducting comparative exper-iments,with a theoretical value of 4.6%for the normalized standard deviation of the receiving-end load power and an average experimental value of 9.6%.The study addressed the power supply issue of near-infrared capsule robots,which is important for early diagnosing and treating gastrointestinal diseases.
