The mechanical properties are essentially different when rock material is subjected to loading or unloading conditions. In this study, loading and unloading tests with various confining pressures are conducted to inve...The mechanical properties are essentially different when rock material is subjected to loading or unloading conditions. In this study, loading and unloading tests with various confining pressures are conducted to investigate the mechanical properties of marble material samples taken from the deep diversion tunnels of Jinping II Hydropower Station. The stress-strain relationship, failure characteristics and strength criterion are compared and analyzed based on the experiment results. The results show： in the loading and unloading test, peak strength, lateral strain, axial strain and plastic deformation increase significantly as the confining pressure increases. Lateral strain increased significantly and obvious lateral dilatancy can be observed to the change of confining pressure; The fracture mode is mainly the single shear fracture for the triaxial compression test and post-peak test, angle between the failure surface and the ends of the rock material becomes smaller as the confining pressure increases. Hock-Brown strength criterion reflects the strength characteristics of marble material under two different unloading conditions, and has some supplementary effects to the rock material of mechanical field.展开更多
A series of full-scale loading tests are performed for a prospective subway tunnel with a rectangular shape including two reliability tests: one stagger-jointed three-ring reliability test, and one ultimate failure te...A series of full-scale loading tests are performed for a prospective subway tunnel with a rectangular shape including two reliability tests: one stagger-jointed three-ring reliability test, and one ultimate failure test on a single ring. Comprehensive measuring programs are designed to record the deformation of both lining structure and joints and the stresses of concrete, bolts and reinforcements. Experimental results show that in both the single-ring and three-ring loading cases, the long sides of tunnel cross section bend inwards while the short sides of tunnel cross section bend outwards. The inner part of joints opens while the outer part of joints closes at places experiencing positive moment and vice versa. Joint's rotational stiffness varies at different locations. Concrete cracking and crushing are the chief damage modes, and they are closely related to the distribution of bending moment. Stagger-jointed fabrication significantly increases the overall rigidity of lining system, which thereby greatly reduces the deformation of both concrete lining and joints in comparison with the single-ring case. It is shown that the routinely-used uniform rigidity model is conservative and the preliminary design can be optimized by applying an effective rigidity ratio(ERR) of 0.5.展开更多
Surrounding rocks at different locations are generally subjected to different stress paths during the process of deep hard rock excavation.In this study,to reveal the mechanical parameters of deep surrounding rock und...Surrounding rocks at different locations are generally subjected to different stress paths during the process of deep hard rock excavation.In this study,to reveal the mechanical parameters of deep surrounding rock under different stress paths,a new cyclic loading and unloading test method for controlled true triaxial loading and unloading and principal stress direction interchange was proposed,and the evolution of mechanical parameters of Shuangjiangkou granite under different stress paths was studied,including the deformation modulus,elastic deformation increment ratios,fracture degree,cohesion and internal friction angle.Additionally,stress path coefficient was defined to characterize different stress paths,and the functional relationships among the stress path coefficient,rock fracture degree difference coefficient,cohesion and internal friction angle were obtained.The results show that during the true triaxial cyclic loading and unloading process,the deformation modulus and cohesion gradually decrease,while the internal friction angle gradually increases with increasing equivalent crack strain.The stress path coefficient is exponentially related to the rock fracture degree difference coefficient.As the stress path coefficient increases,the degrees of cohesion weakening and internal friction angle strengthening decrease linearly.During cyclic loading and unloading under true triaxial principal stress direction interchange,the direction of crack development changes,and the deformation modulus increases,while the cohesion and internal friction angle decrease slightly,indicating that the principal stress direction interchange has a strengthening effect on the surrounding rocks.Finally,the influences of the principal stress interchange direction on the stabilities of deep engineering excavation projects are discussed.展开更多
Triaxial cyclic loading tests have been performed to assess the influence of plastic deformation on inelastic deformational properties of anisotropic argillite with bedding planes which is regarded as a kind of transv...Triaxial cyclic loading tests have been performed to assess the influence of plastic deformation on inelastic deformational properties of anisotropic argillite with bedding planes which is regarded as a kind of transversely isotropic media.Considering argillite's anisotropy and inelastic deformational properties,theoretical formulae for calculating oriented elastic parameters were deduced by the unloading curves,which can be better fitted for the description of its elasticity than loading curves.Test results indicate that with the growth of accumulated plastic,strain,the apparent elastic modulus of argillite decreases in a form of exponential decay function,whereas the apparent Poisson ratio increase in a form of power equation.A ratio of unloading recoverable strain to the total strain increment occurred during a loading cycle is defined to illustrate the characteristic relations between anisotropic coupled elasto-plastic deformation and plastic strain.It is significant to observe that high stress level and plastic history have an inhibiting effect on argillite anisotropy.展开更多
A reasonable evaluation of unloading deformation characteristics is of great significance for the effective analysis of deformation and stability of surrounding rocks after underground excavation.In this study,the dam...A reasonable evaluation of unloading deformation characteristics is of great significance for the effective analysis of deformation and stability of surrounding rocks after underground excavation.In this study,the damage-controlled cyclic triaxial loading tests were conducted to investigate the pore compaction mechanism and its influences on the unloading deformation behavior of red sandstone,including Young’s modulus,Poisson’s ratio,volumetric strain,and irreversible strain.The experimental results show that the increases of volumetric and irreversible strains of rocks can be attributed to the compaction mechanism,which almost dominates the entire pre-peak deformation process.The unloading deformation consists of the reversible linear and nonlinear strains,and the irreversible strain under the influence of the porous grain structure.The pre-peak Young’s modulus tends to increase and then decrease due to the influence of the unloading irreversible strain.However,it hardly changes with the increasing volumetric strain compaction under the influence of reversible nonlinear strain.Instead,the initial unloading tangent modulus is highly related to the volumetric strain,and clearly reflects the compaction state of red sandstone.Furthermore,both the reversible nonlinear and irreversible unloading deformations are independent of confining pressure.This study is beneficial for the theoretical modeling and prediction of cyclic unloading deformation behavior of red sandstone.展开更多
Due to creep characteristics of wood,long-term loading can cause a significant stress loss of steel bars in rein-forced glulam beams and high long-term deflection of the beam midspan.In this study,15 glulam beams were...Due to creep characteristics of wood,long-term loading can cause a significant stress loss of steel bars in rein-forced glulam beams and high long-term deflection of the beam midspan.In this study,15 glulam beams were subjected to a 90-day long-term loading test,and the effects of long-term loading value,reinforcement ratio and prestress level on the stress of steel bars,midspan long-term deflection,and other parameters were compared and analyzed.The main conclusions drawn from this study were that the long-term deflection of the reinforced glulam beams accounted for 22.5%,20.6%,and 18.2%of the total deflection respectively when the loading value was 20%,30%,and 40%of the estimated ultimate load under the long-term loading.The higher the loading level was,the smaller the proportion of the long-term deflection in the total deflection was.Compared with ordinary glulam beams,the long-term deflection of the reinforced glulam beam was even smaller.Under the condition of the constant loading level,the total stress value of the steel bars decreased by 17.5%,13.6%,and 9.1%,and the proportion of the long-term deflection of the beam midspan in the total deflection was 26.9%,24.2%,and 20.6%respectively when the reinforcement ratio was 2.05%,2.68%,and 3.39%.With the increase of the reinfor-cement ratio,the stress loss of the steel bars decreased,and the proportion of the long-term deflection decreased as well.When other conditions remained constant and the prestress level of the steel bars was 0 MPa,30 MPa,and 60 MPa,the total stress value of the steel bars decreased by 9.1%,9.4%,and 10.2%,respectively,and the propor-tion of the long-term deflection in the total deflection was 20.6%,26.1%,and 64.9%,respectively.With the increase of the prestress value,the stress loss of the steel bars increased,and the proportion of the long-term deflection increased as well.展开更多
China's railway prestressed concrete bridge has more than 600000 holes,prestressed engineering is a key force system affecting the safety and durability of the prestressed concrete bridge structure,its constructio...China's railway prestressed concrete bridge has more than 600000 holes,prestressed engineering is a key force system affecting the safety and durability of the prestressed concrete bridge structure,its construction quality is easily affected by traditional manual operation technology,resulting in low construction efficiency and control accuracy,easy to form a hidden danger of quality and safety,it is difficult to meet the needs of less humanized,standardized intelligent construction trend.Based on the research on the intelligent prestressed construction control and testing technology and equipment for railway bridges,this paper proposes the integration of intelligent prestressed tension control and tunnel friction test of railway bridges,intelligent grouting control of tunnel and intelligent testing of beam construction quality,and sets up a complete technical system and integrated equipment for intelligent prestressed construction of bridges based on the industrial Internet of Things(IoT).Overall,improve the quality and efficiency of bridge production,construction,and management.展开更多
This paper describes low cyclic loading testing of nine angle-steel concrete column （ASCC） specimens. In the tests, the influence of the shear-span ratio, axial compression ratio and shear steel plate ratio on the h...This paper describes low cyclic loading testing of nine angle-steel concrete column （ASCC） specimens. In the tests, the influence of the shear-span ratio, axial compression ratio and shear steel plate ratio on the hysteretic behavior, energy dissipation, strength degradation, stiffness degradation, skeleton curve and ductility of the ASCCs is studied. Based on the test results, some conclusions are presented. The P-A and sectional M -φ hysteretic models for the ASCCs are presented in a companion paper （Zheng and Ji, 2008）.展开更多
A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the...A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the pile tip will weaken the mobilization of end resistance. The ultimate tip resistance of post-grouted pile is 2.05 times that of the pile without post-grouting and the ultimate tip resistance in the second load cycle is 2.31 times that of pile in the first load cycle. The relationship between unit end resistance and displacement follows a linear model and a bilinear mode in the first load cycle and the second load cycle, respectively, whereas the unit end resistance-displacement response of post-grouted bored pile can be simulated using a bilinear mode. The critical end resistance ranges between 2 000 kN and 3 000 kN and the critical displacement ranges between 2.5 mm and 4.5 mm in the bilinear mode. As for piles rested on moderately-weathered peliticsiltstone, the socketed length has no effect on the end resistance because of the existence of loose debris.展开更多
Bi-directional static loading test adopting load cells is widely used around the world at present,with increase in diameter and length of deep foundations.In this paper,a new simple conversion method to predict the eq...Bi-directional static loading test adopting load cells is widely used around the world at present,with increase in diameter and length of deep foundations.In this paper,a new simple conversion method to predict the equivalent pile head load-settlement curve considering elastic shortening of deep foundation was put forward according to the load transfer mechanism.The proposed conversion method was applied to root caisson foundation in a bridge and to large diameter pipe piles in a sea wind power plant.Some new load cells,test procedure,and construction technology were adopted based on the applications to different deep foundations,which could enlarge the application scopes of bi-directional loading test.A new type of bi-directional loading test for pipe pile was conducted,in which the load cell was installed and loaded after the pipe pile with special connector has been set up.Unlike the conventional bi-directional loading test,the load cell can be reused and shows an evident economic benefit.展开更多
Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading...Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading.In this paper,repeated load triaxial tests were performed on coarse-grained soil(CGS),and the axial permanent strain of CGS under different confining pressures and dynamic stress amplitudes was analysed.Permanent deformation behaviors of CGS were categorized based on the variation trend of permanent strain rate with accumulated permanent strain and the shakedown theory.A prediction model of permanent deformation considering stress state and number of load cycles was established,and the ranges of parameters for different types of dynamic behaviors were also divided.The results indicated that the variational trend of permanent strain rate with accumulated permanent strain can be used as a basis for classifying dynamic behaviors of CGS.The stress state(confining pressure and dynamic stress amplitude)has significant effects on the permanent strain rate.The accumulative characteristics of permanent deformation of CGS with the number of load cycles can be described by a power function,and the model parameters can reflect the influence of confining pressure and dynamic stress amplitude.The study’s results could help deepen understanding of the permanent deformation characteristics of CGS.展开更多
Although the study of TM(Thermo Mechanics),HM(Hydraulic-Mechanics) and THM(Thermo-Hydraulic-Mechanics) coupling under a loading test have been under development,rock failure analysis under THM coupling and unloading i...Although the study of TM(Thermo Mechanics),HM(Hydraulic-Mechanics) and THM(Thermo-Hydraulic-Mechanics) coupling under a loading test have been under development,rock failure analysis under THM coupling and unloading is an emerging topic.Based on a high temperature triaxial unloading seep test for phyllite,this paper discusses the deformation and failure mechanism of phyllites under the "H M,T→H,T→M" incomplete coupling model with unloading conditions.The results indicate that the elastic modulus and initial permeability decrease and the Poisson's ratio increases with increasing temperature;the elastic modulus decreases and the Poisson's ratio and initial permeability increase with increasing water pressure.During the unloading process,rock penetrability is small at the initial elastic deformation phase,but the penetrability increases near the end of the elastic deformation phase;mechanisms involving temperature and water pressure affect penetrability differently.Phyllite failure occurs from the initial thermal damage of the rock materials,splitting and softening(which is caused by pore water pressure),and the pressure difference which is formed from the loading axial pressure and unloading confining pressure.The phyllite failure mechanism is a transtensional(tension-shearing) failure.展开更多
Ultra-high molecular weight polyethylene(UHMWPE)fiber composite has been extensively used to construct lightweight protective structures against ballistic impacts,yet little is known about its performance when subject...Ultra-high molecular weight polyethylene(UHMWPE)fiber composite has been extensively used to construct lightweight protective structures against ballistic impacts,yet little is known about its performance when subjected to combined blast and fragment impacts.Built upon a recently developed laboratory-scale experimental technique to generate simulated combined loading through the impact of a fragment-foam composite projectile launched from a light gas gun,the dynamic responses of fullyclamped UHMWPE plates subjected to combined loading were characterized experimentally,with corresponding deformation and failure modes compared with those measured with simulated blast loading alone.Subsequently,to explore the underlying physical mechanisms,three-dimensional(3D)numerical simulations with the method of finite elements(FE)were systematically carried out.Numerical predictions compared favorably well with experimental measurements,thus validating the feasibility of the established FE model.Relative to the case of blast loading alone,combined blast and fragment loading led to larger maximum deflections of clamped UHMWPE plates.The position of the FSP in the foam sabot affected significantly the performance of a UHMWPE target,either enhancing or decreasing its ballistic resistance.When the blast loading and fragment impact arrived simultaneously at the target,its ballistic resistance was superior to that achieved when subjected to fragment impact alone,and benefited from the accelerated movement of the target due to simultaneous blast loading.展开更多
For load-controlled and displacement-controlled test data of piles cyclically axiallly loaded in clay, the displacement conditions are suggested for determining the shaft capacity. According to the suggested displacem...For load-controlled and displacement-controlled test data of piles cyclically axiallly loaded in clay, the displacement conditions are suggested for determining the shaft capacity. According to the suggested displacement conditions, not only the results of shaft capacity from laboratory model piles are close to those from in-situ piles, but also the results of load-controlled tests are in satisfactory agreement with those of displacement-controlled test. Moreover, based on the test data of laboratory model piles in combination with the test data published, the paper suggests the values of the normalized shaft capacity of piles under a variety of static and cyclic loading combinations.展开更多
The effects of microstructure on quasi-static transverse loading behavior of 3D circular braided composite tubes were studied. Transverse loading tests were conducted. Transverse load-deflection curves were obtained t...The effects of microstructure on quasi-static transverse loading behavior of 3D circular braided composite tubes were studied. Transverse loading tests were conducted. Transverse load-deflection curves were obtained to analyze the effects of braiding parameters including the braiding angle, the wall thickness, and the diameter on the transverse loading of 3D circular braided composite tubes. Breaking loads, moduli and strengths had also been used to describe the transverse loading behaviors. The failure morphologies were shown to reveal damage mechanisms. From the results, the increase in braiding angle, wall thickness and diameter increases the ability of anti-deformation and breaking load of braided tubes. The breaking load of specimen with a braiding angle of 45° is about 1.68 times that of specimen with a braiding angle of 15°. The breaking load of specimen with 4 layers of yarns is about 2.15 times that of specimen with 2 layers of yarns. The breaking load of the tube with a diameter of 25.5 mm is about 2.39 times that of the tube with a diameter of 20.5 mm.展开更多
Urbanization is the physical growth of urban areas as a result of global change. As the land cost is increasing tremendously and decreasing availability of good construction site is building up pressure on the enginee...Urbanization is the physical growth of urban areas as a result of global change. As the land cost is increasing tremendously and decreasing availability of good construction site is building up pressure on the engineers to utilize even the poorest site either by providing special type of foundation or by improving ground in urban centres. In this context literature is reviewed for use of landfill site for housing. The site exploration for old dump site was carried out to assess subsoil characteristics. The objective was to evolve strategy for economical feasible ground improvement technique to obtain permissible bearing capacity of 150 kPa and total settlement not more than 50 mm. The tests carried out are load tests with geotextile mat and stone filled wire mess matress. The analysis was attempted to evaluate the soil response and bearing capacity. The site can be used for construction of low rise housing for rehabilitation of displaced persons under TP scheme within city area utilizing old landfill sites.展开更多
Stress ribbon bridges have many advantages and became recently more popular mostly because of their versatile form, slender decks giving a light aesthetic impression and durability assured by post tensioned concrete. ...Stress ribbon bridges have many advantages and became recently more popular mostly because of their versatile form, slender decks giving a light aesthetic impression and durability assured by post tensioned concrete. The paper presents the first in Poland stress Ribbon Bridge constructed last year. A static and dynamic analyse of the model is presented as well as construction solutions which were used to achieve the highest durability. The bridge was checked during static and dynamic load test. The results of this prove test were compared with results obtained from examination and study of other different bridge structures. It confirmed that the bridge has good dynamic resistance and greater stiffness than assumed in the design.展开更多
Fixed-wing aircraft cannot maintain optimal aerodynamic performance at different flight speeds. As a type of morphing aircraft, the shear variable-sweep wing(SVSW) can dramatically improve its aerodynamic performance ...Fixed-wing aircraft cannot maintain optimal aerodynamic performance at different flight speeds. As a type of morphing aircraft, the shear variable-sweep wing(SVSW) can dramatically improve its aerodynamic performance by altering its shape to adapt to various flight conditions.In order to achieve smooth continuous shear deformation, SVSW's skin adopts a flexible composite skin design instead of traditional aluminum alloy materials. However, this also brings about the non-linear difficulty in stiffness modeling and calculation. In this research, a new SVSW design and efficient stiffness modeling method are proposed. Based on shear deformation theory, the flexible composite skin is equivalently modeled as diagonally arranged nonlinear springs, simulating the elastic force interaction between the skin and the mechanism. By shear loading tests of flexible composite skin, the accuracy of this flexible composite skin modeling method is verified. The SVSW stiffness model was established, and its accuracy was verified through static loading tests. The effects of root connection, sweep angles, and flexible composite skin on the SVSW stiffness are analyzed. Finally, considering three typical flight conditions of SVSW: low-speed flow(Ma = 0.3,Re = 5.82 × 10^(6)), transonic flow(Ma = 0.9, Re = 3.44 × 10^(6)), and supersonic flow(Ma = 3,Re = 7.51 × 10^(6)), the stiffness characteristics of SVSW under flight conditions were evaluated.The calculated results guide the application of SVSW.展开更多
The deteriorated continuous rigid frame bridge is strengthened by external prestressing. Static loading tests wereconducted before and after the bridge rehabilitation to verify the effectiveness of the rehabilitation ...The deteriorated continuous rigid frame bridge is strengthened by external prestressing. Static loading tests wereconducted before and after the bridge rehabilitation to verify the effectiveness of the rehabilitation process. Thestiffness of the repaired bridge is improved, and the maximum deflection of the load test is reduced from 37.9 to27.6 mm. A bridge health monitoring system is installed after the bridge is reinforced. To achieve an easy assessmentof the bridge’s safety status by directly using transferred data, a real-time safety warning system is createdbased on a five-level safety standard. The threshold for each safety level will be determined by theoretical calculationsand the outcomes of static loading tests. The highest risk threshold will be set at the ultimate limit statevalue. The remaining levels, namely middle risk, low risk, and very low risk, will be determined usingreduction coefficients of 0.95, 0.9, and 0.8, respectively.展开更多
In order to mitigate the risk of geological disasters induced by fault activation when roadways intersect reverse faults in coal mining,this paper uses a combination of mechanical models with PFC2D software.A mechanic...In order to mitigate the risk of geological disasters induced by fault activation when roadways intersect reverse faults in coal mining,this paper uses a combination of mechanical models with PFC2D software.A mechanical model is introduced to represent various fault angles,followed by a series of PFC2D loading and unloading tests to validate the model and investigate fault instability and crack propagation under different excavation rates and angles.The results show that(1)the theoretical fault model,impacted by roadway advancing,shows a linear reduction in horizontal stress at a rate of-2.01 MPa/m,while vertical stress increases linearly at 4.02 MPa/m.(2)Atfield excavation speeds of 2.4,4.8,7.2,and 9.6 m/day,the vertical loading rates for the model are 2.23,4.47,6.70,and 8.93 Pa/s,respectively.(3)Roadway advancement primarily causes tensile-compressive failures in front of the roadway,with a decrease in tensile cracks as the stress rate increases.(4)An increase in the fault angle leads to denser cracking on the fault plane,with negligible cracking near the fault itself.The dominant crack orientation is approximately 90°,aligned with the vertical stress.展开更多
基金Supported by National Natural Science Foundation of China(No.50974100)WHUT(NO.125106002)
文摘The mechanical properties are essentially different when rock material is subjected to loading or unloading conditions. In this study, loading and unloading tests with various confining pressures are conducted to investigate the mechanical properties of marble material samples taken from the deep diversion tunnels of Jinping II Hydropower Station. The stress-strain relationship, failure characteristics and strength criterion are compared and analyzed based on the experiment results. The results show： in the loading and unloading test, peak strength, lateral strain, axial strain and plastic deformation increase significantly as the confining pressure increases. Lateral strain increased significantly and obvious lateral dilatancy can be observed to the change of confining pressure; The fracture mode is mainly the single shear fracture for the triaxial compression test and post-peak test, angle between the failure surface and the ends of the rock material becomes smaller as the confining pressure increases. Hock-Brown strength criterion reflects the strength characteristics of marble material under two different unloading conditions, and has some supplementary effects to the rock material of mechanical field.
基金the National Natural Science Foundation of China(No.41372276)the Shanghai SASAC Technology Innovation and Energy Level Promotion Project(No.2013017)
文摘A series of full-scale loading tests are performed for a prospective subway tunnel with a rectangular shape including two reliability tests: one stagger-jointed three-ring reliability test, and one ultimate failure test on a single ring. Comprehensive measuring programs are designed to record the deformation of both lining structure and joints and the stresses of concrete, bolts and reinforcements. Experimental results show that in both the single-ring and three-ring loading cases, the long sides of tunnel cross section bend inwards while the short sides of tunnel cross section bend outwards. The inner part of joints opens while the outer part of joints closes at places experiencing positive moment and vice versa. Joint's rotational stiffness varies at different locations. Concrete cracking and crushing are the chief damage modes, and they are closely related to the distribution of bending moment. Stagger-jointed fabrication significantly increases the overall rigidity of lining system, which thereby greatly reduces the deformation of both concrete lining and joints in comparison with the single-ring case. It is shown that the routinely-used uniform rigidity model is conservative and the preliminary design can be optimized by applying an effective rigidity ratio(ERR) of 0.5.
基金the financial support from the National Natural Science Foundation of China(Grant Nos.51839003 and 42207221).
文摘Surrounding rocks at different locations are generally subjected to different stress paths during the process of deep hard rock excavation.In this study,to reveal the mechanical parameters of deep surrounding rock under different stress paths,a new cyclic loading and unloading test method for controlled true triaxial loading and unloading and principal stress direction interchange was proposed,and the evolution of mechanical parameters of Shuangjiangkou granite under different stress paths was studied,including the deformation modulus,elastic deformation increment ratios,fracture degree,cohesion and internal friction angle.Additionally,stress path coefficient was defined to characterize different stress paths,and the functional relationships among the stress path coefficient,rock fracture degree difference coefficient,cohesion and internal friction angle were obtained.The results show that during the true triaxial cyclic loading and unloading process,the deformation modulus and cohesion gradually decrease,while the internal friction angle gradually increases with increasing equivalent crack strain.The stress path coefficient is exponentially related to the rock fracture degree difference coefficient.As the stress path coefficient increases,the degrees of cohesion weakening and internal friction angle strengthening decrease linearly.During cyclic loading and unloading under true triaxial principal stress direction interchange,the direction of crack development changes,and the deformation modulus increases,while the cohesion and internal friction angle decrease slightly,indicating that the principal stress direction interchange has a strengthening effect on the surrounding rocks.Finally,the influences of the principal stress interchange direction on the stabilities of deep engineering excavation projects are discussed.
基金Program(2011CB710601) supported by National Basic Research Program of ChinaProject(50925933) supported by National Natural Science Foundation of China+1 种基金Project(2008BAB29B03) supported by National Key Technology Research and Development Program of ChinaProject(2010-122-011) supported by Guizhou Provincial Department of Transportation,China
文摘Triaxial cyclic loading tests have been performed to assess the influence of plastic deformation on inelastic deformational properties of anisotropic argillite with bedding planes which is regarded as a kind of transversely isotropic media.Considering argillite's anisotropy and inelastic deformational properties,theoretical formulae for calculating oriented elastic parameters were deduced by the unloading curves,which can be better fitted for the description of its elasticity than loading curves.Test results indicate that with the growth of accumulated plastic,strain,the apparent elastic modulus of argillite decreases in a form of exponential decay function,whereas the apparent Poisson ratio increase in a form of power equation.A ratio of unloading recoverable strain to the total strain increment occurred during a loading cycle is defined to illustrate the characteristic relations between anisotropic coupled elasto-plastic deformation and plastic strain.It is significant to observe that high stress level and plastic history have an inhibiting effect on argillite anisotropy.
基金supported by the National Natural Science Foundation of China(Grant No.52109135)the Key R&D Projects of Sichuan Province,China(Grant No.2022YFSY0007)the Postdoctoral Research Foundation of China(Grant No.2019M653402).
文摘A reasonable evaluation of unloading deformation characteristics is of great significance for the effective analysis of deformation and stability of surrounding rocks after underground excavation.In this study,the damage-controlled cyclic triaxial loading tests were conducted to investigate the pore compaction mechanism and its influences on the unloading deformation behavior of red sandstone,including Young’s modulus,Poisson’s ratio,volumetric strain,and irreversible strain.The experimental results show that the increases of volumetric and irreversible strains of rocks can be attributed to the compaction mechanism,which almost dominates the entire pre-peak deformation process.The unloading deformation consists of the reversible linear and nonlinear strains,and the irreversible strain under the influence of the porous grain structure.The pre-peak Young’s modulus tends to increase and then decrease due to the influence of the unloading irreversible strain.However,it hardly changes with the increasing volumetric strain compaction under the influence of reversible nonlinear strain.Instead,the initial unloading tangent modulus is highly related to the volumetric strain,and clearly reflects the compaction state of red sandstone.Furthermore,both the reversible nonlinear and irreversible unloading deformations are independent of confining pressure.This study is beneficial for the theoretical modeling and prediction of cyclic unloading deformation behavior of red sandstone.
基金This research work was supported by the Fundamental Research Funds for the Central Universities(2572017DB02)the natural science foundation of Heilongjiang Province(LH2019E005)the natural science of Heilongjiang Province(LH2020E009).
文摘Due to creep characteristics of wood,long-term loading can cause a significant stress loss of steel bars in rein-forced glulam beams and high long-term deflection of the beam midspan.In this study,15 glulam beams were subjected to a 90-day long-term loading test,and the effects of long-term loading value,reinforcement ratio and prestress level on the stress of steel bars,midspan long-term deflection,and other parameters were compared and analyzed.The main conclusions drawn from this study were that the long-term deflection of the reinforced glulam beams accounted for 22.5%,20.6%,and 18.2%of the total deflection respectively when the loading value was 20%,30%,and 40%of the estimated ultimate load under the long-term loading.The higher the loading level was,the smaller the proportion of the long-term deflection in the total deflection was.Compared with ordinary glulam beams,the long-term deflection of the reinforced glulam beam was even smaller.Under the condition of the constant loading level,the total stress value of the steel bars decreased by 17.5%,13.6%,and 9.1%,and the proportion of the long-term deflection of the beam midspan in the total deflection was 26.9%,24.2%,and 20.6%respectively when the reinforcement ratio was 2.05%,2.68%,and 3.39%.With the increase of the reinfor-cement ratio,the stress loss of the steel bars decreased,and the proportion of the long-term deflection decreased as well.When other conditions remained constant and the prestress level of the steel bars was 0 MPa,30 MPa,and 60 MPa,the total stress value of the steel bars decreased by 9.1%,9.4%,and 10.2%,respectively,and the propor-tion of the long-term deflection in the total deflection was 20.6%,26.1%,and 64.9%,respectively.With the increase of the prestress value,the stress loss of the steel bars increased,and the proportion of the long-term deflection increased as well.
基金Scientific and Technological Development Project of China Railway Design Group Co.,Ltd.(No.2022A02480005)Technology Development Project of China Railway Design Group Co.,Ltd.(No.2023A0248001).
文摘China's railway prestressed concrete bridge has more than 600000 holes,prestressed engineering is a key force system affecting the safety and durability of the prestressed concrete bridge structure,its construction quality is easily affected by traditional manual operation technology,resulting in low construction efficiency and control accuracy,easy to form a hidden danger of quality and safety,it is difficult to meet the needs of less humanized,standardized intelligent construction trend.Based on the research on the intelligent prestressed construction control and testing technology and equipment for railway bridges,this paper proposes the integration of intelligent prestressed tension control and tunnel friction test of railway bridges,intelligent grouting control of tunnel and intelligent testing of beam construction quality,and sets up a complete technical system and integrated equipment for intelligent prestressed construction of bridges based on the industrial Internet of Things(IoT).Overall,improve the quality and efficiency of bridge production,construction,and management.
基金the New Century Excellent Talents in University Under Grant No.290Heilongjiang Key Program on Science and Technology Under Grant No.GC04A609Harbin Key Program on Science and Technology Under Grant No.2004AA9CS187
文摘This paper describes low cyclic loading testing of nine angle-steel concrete column （ASCC） specimens. In the tests, the influence of the shear-span ratio, axial compression ratio and shear steel plate ratio on the hysteretic behavior, energy dissipation, strength degradation, stiffness degradation, skeleton curve and ductility of the ASCCs is studied. Based on the test results, some conclusions are presented. The P-A and sectional M -φ hysteretic models for the ASCCs are presented in a companion paper （Zheng and Ji, 2008）.
基金Project(51078330) supported by the National Natural Science Foundation of ChinaProject(2012MS21339) supported by China Postdoctoral Science FoundationProject(2012GN012) supported by the Independent Innovation Foundation of Shandong University, China
文摘A series of well-designed full-scale destructive load tests were conducted on six bored piles to investigate the influence of loose debris at the pile tip on end resistance. The results show that soft debris below the pile tip will weaken the mobilization of end resistance. The ultimate tip resistance of post-grouted pile is 2.05 times that of the pile without post-grouting and the ultimate tip resistance in the second load cycle is 2.31 times that of pile in the first load cycle. The relationship between unit end resistance and displacement follows a linear model and a bilinear mode in the first load cycle and the second load cycle, respectively, whereas the unit end resistance-displacement response of post-grouted bored pile can be simulated using a bilinear mode. The critical end resistance ranges between 2 000 kN and 3 000 kN and the critical displacement ranges between 2.5 mm and 4.5 mm in the bilinear mode. As for piles rested on moderately-weathered peliticsiltstone, the socketed length has no effect on the end resistance because of the existence of loose debris.
基金Supported by the National Natural Science Foundation of China(50908048)the Priority Academic Program Development(PAPD)Project of JiangsuHigher Education Institutions
文摘Bi-directional static loading test adopting load cells is widely used around the world at present,with increase in diameter and length of deep foundations.In this paper,a new simple conversion method to predict the equivalent pile head load-settlement curve considering elastic shortening of deep foundation was put forward according to the load transfer mechanism.The proposed conversion method was applied to root caisson foundation in a bridge and to large diameter pipe piles in a sea wind power plant.Some new load cells,test procedure,and construction technology were adopted based on the applications to different deep foundations,which could enlarge the application scopes of bi-directional loading test.A new type of bi-directional loading test for pipe pile was conducted,in which the load cell was installed and loaded after the pipe pile with special connector has been set up.Unlike the conventional bi-directional loading test,the load cell can be reused and shows an evident economic benefit.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.51878666 and 51678572).
文摘Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading.In this paper,repeated load triaxial tests were performed on coarse-grained soil(CGS),and the axial permanent strain of CGS under different confining pressures and dynamic stress amplitudes was analysed.Permanent deformation behaviors of CGS were categorized based on the variation trend of permanent strain rate with accumulated permanent strain and the shakedown theory.A prediction model of permanent deformation considering stress state and number of load cycles was established,and the ranges of parameters for different types of dynamic behaviors were also divided.The results indicated that the variational trend of permanent strain rate with accumulated permanent strain can be used as a basis for classifying dynamic behaviors of CGS.The stress state(confining pressure and dynamic stress amplitude)has significant effects on the permanent strain rate.The accumulative characteristics of permanent deformation of CGS with the number of load cycles can be described by a power function,and the model parameters can reflect the influence of confining pressure and dynamic stress amplitude.The study’s results could help deepen understanding of the permanent deformation characteristics of CGS.
基金supported by National Natural Science Foundation of China (Grant No. 41102189,No. 41002110 and No. 41230635)Projects of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Grant No. SKLGP2009Z002,No. SKLGP2009Z012)Research Fund for the Doctoral Program of Higher Education of China(Grant No. 20105122110008)
文摘Although the study of TM(Thermo Mechanics),HM(Hydraulic-Mechanics) and THM(Thermo-Hydraulic-Mechanics) coupling under a loading test have been under development,rock failure analysis under THM coupling and unloading is an emerging topic.Based on a high temperature triaxial unloading seep test for phyllite,this paper discusses the deformation and failure mechanism of phyllites under the "H M,T→H,T→M" incomplete coupling model with unloading conditions.The results indicate that the elastic modulus and initial permeability decrease and the Poisson's ratio increases with increasing temperature;the elastic modulus decreases and the Poisson's ratio and initial permeability increase with increasing water pressure.During the unloading process,rock penetrability is small at the initial elastic deformation phase,but the penetrability increases near the end of the elastic deformation phase;mechanisms involving temperature and water pressure affect penetrability differently.Phyllite failure occurs from the initial thermal damage of the rock materials,splitting and softening(which is caused by pore water pressure),and the pressure difference which is formed from the loading axial pressure and unloading confining pressure.The phyllite failure mechanism is a transtensional(tension-shearing) failure.
基金supported by the National Natural Science Foundation of China(Grant No.12032010,11902155 and 12072250)by the Natural Science Foundation of Jiangsu Province(Grant No.BK20190382)+2 种基金by the Research Fund of State Key Laboratory of Mechanics and Control of Mechanical Structures(Grant No.MCMS-I-0222K01)by the Fund of Prospective Layout of Scientific Research for NUAAby the Foundation for the Priority Academic Program Development of Jiangsu Higher Education Institutions。
文摘Ultra-high molecular weight polyethylene(UHMWPE)fiber composite has been extensively used to construct lightweight protective structures against ballistic impacts,yet little is known about its performance when subjected to combined blast and fragment impacts.Built upon a recently developed laboratory-scale experimental technique to generate simulated combined loading through the impact of a fragment-foam composite projectile launched from a light gas gun,the dynamic responses of fullyclamped UHMWPE plates subjected to combined loading were characterized experimentally,with corresponding deformation and failure modes compared with those measured with simulated blast loading alone.Subsequently,to explore the underlying physical mechanisms,three-dimensional(3D)numerical simulations with the method of finite elements(FE)were systematically carried out.Numerical predictions compared favorably well with experimental measurements,thus validating the feasibility of the established FE model.Relative to the case of blast loading alone,combined blast and fragment loading led to larger maximum deflections of clamped UHMWPE plates.The position of the FSP in the foam sabot affected significantly the performance of a UHMWPE target,either enhancing or decreasing its ballistic resistance.When the blast loading and fragment impact arrived simultaneously at the target,its ballistic resistance was superior to that achieved when subjected to fragment impact alone,and benefited from the accelerated movement of the target due to simultaneous blast loading.
基金This project is financially sponsored by the Chinese National Natural Scinece Foundation
文摘For load-controlled and displacement-controlled test data of piles cyclically axiallly loaded in clay, the displacement conditions are suggested for determining the shaft capacity. According to the suggested displacement conditions, not only the results of shaft capacity from laboratory model piles are close to those from in-situ piles, but also the results of load-controlled tests are in satisfactory agreement with those of displacement-controlled test. Moreover, based on the test data of laboratory model piles in combination with the test data published, the paper suggests the values of the normalized shaft capacity of piles under a variety of static and cyclic loading combinations.
文摘The effects of microstructure on quasi-static transverse loading behavior of 3D circular braided composite tubes were studied. Transverse loading tests were conducted. Transverse load-deflection curves were obtained to analyze the effects of braiding parameters including the braiding angle, the wall thickness, and the diameter on the transverse loading of 3D circular braided composite tubes. Breaking loads, moduli and strengths had also been used to describe the transverse loading behaviors. The failure morphologies were shown to reveal damage mechanisms. From the results, the increase in braiding angle, wall thickness and diameter increases the ability of anti-deformation and breaking load of braided tubes. The breaking load of specimen with a braiding angle of 45° is about 1.68 times that of specimen with a braiding angle of 15°. The breaking load of specimen with 4 layers of yarns is about 2.15 times that of specimen with 2 layers of yarns. The breaking load of the tube with a diameter of 25.5 mm is about 2.39 times that of the tube with a diameter of 20.5 mm.
文摘Urbanization is the physical growth of urban areas as a result of global change. As the land cost is increasing tremendously and decreasing availability of good construction site is building up pressure on the engineers to utilize even the poorest site either by providing special type of foundation or by improving ground in urban centres. In this context literature is reviewed for use of landfill site for housing. The site exploration for old dump site was carried out to assess subsoil characteristics. The objective was to evolve strategy for economical feasible ground improvement technique to obtain permissible bearing capacity of 150 kPa and total settlement not more than 50 mm. The tests carried out are load tests with geotextile mat and stone filled wire mess matress. The analysis was attempted to evaluate the soil response and bearing capacity. The site can be used for construction of low rise housing for rehabilitation of displaced persons under TP scheme within city area utilizing old landfill sites.
文摘Stress ribbon bridges have many advantages and became recently more popular mostly because of their versatile form, slender decks giving a light aesthetic impression and durability assured by post tensioned concrete. The paper presents the first in Poland stress Ribbon Bridge constructed last year. A static and dynamic analyse of the model is presented as well as construction solutions which were used to achieve the highest durability. The bridge was checked during static and dynamic load test. The results of this prove test were compared with results obtained from examination and study of other different bridge structures. It confirmed that the bridge has good dynamic resistance and greater stiffness than assumed in the design.
基金Supported by the National Nature Science Foundation of China(Grant No.52192631 and No.52105013).
文摘Fixed-wing aircraft cannot maintain optimal aerodynamic performance at different flight speeds. As a type of morphing aircraft, the shear variable-sweep wing(SVSW) can dramatically improve its aerodynamic performance by altering its shape to adapt to various flight conditions.In order to achieve smooth continuous shear deformation, SVSW's skin adopts a flexible composite skin design instead of traditional aluminum alloy materials. However, this also brings about the non-linear difficulty in stiffness modeling and calculation. In this research, a new SVSW design and efficient stiffness modeling method are proposed. Based on shear deformation theory, the flexible composite skin is equivalently modeled as diagonally arranged nonlinear springs, simulating the elastic force interaction between the skin and the mechanism. By shear loading tests of flexible composite skin, the accuracy of this flexible composite skin modeling method is verified. The SVSW stiffness model was established, and its accuracy was verified through static loading tests. The effects of root connection, sweep angles, and flexible composite skin on the SVSW stiffness are analyzed. Finally, considering three typical flight conditions of SVSW: low-speed flow(Ma = 0.3,Re = 5.82 × 10^(6)), transonic flow(Ma = 0.9, Re = 3.44 × 10^(6)), and supersonic flow(Ma = 3,Re = 7.51 × 10^(6)), the stiffness characteristics of SVSW under flight conditions were evaluated.The calculated results guide the application of SVSW.
文摘The deteriorated continuous rigid frame bridge is strengthened by external prestressing. Static loading tests wereconducted before and after the bridge rehabilitation to verify the effectiveness of the rehabilitation process. Thestiffness of the repaired bridge is improved, and the maximum deflection of the load test is reduced from 37.9 to27.6 mm. A bridge health monitoring system is installed after the bridge is reinforced. To achieve an easy assessmentof the bridge’s safety status by directly using transferred data, a real-time safety warning system is createdbased on a five-level safety standard. The threshold for each safety level will be determined by theoretical calculationsand the outcomes of static loading tests. The highest risk threshold will be set at the ultimate limit statevalue. The remaining levels, namely middle risk, low risk, and very low risk, will be determined usingreduction coefficients of 0.95, 0.9, and 0.8, respectively.
基金Australian Research Council,Grant/Award Number:DP210100437National Natural Science Foundation of China,Grant/Award Number:52274102Graduate Research and Innovation Projects of Jiangsu Province,Grant/Award Number:KYCX21_2335。
文摘In order to mitigate the risk of geological disasters induced by fault activation when roadways intersect reverse faults in coal mining,this paper uses a combination of mechanical models with PFC2D software.A mechanical model is introduced to represent various fault angles,followed by a series of PFC2D loading and unloading tests to validate the model and investigate fault instability and crack propagation under different excavation rates and angles.The results show that(1)the theoretical fault model,impacted by roadway advancing,shows a linear reduction in horizontal stress at a rate of-2.01 MPa/m,while vertical stress increases linearly at 4.02 MPa/m.(2)Atfield excavation speeds of 2.4,4.8,7.2,and 9.6 m/day,the vertical loading rates for the model are 2.23,4.47,6.70,and 8.93 Pa/s,respectively.(3)Roadway advancement primarily causes tensile-compressive failures in front of the roadway,with a decrease in tensile cracks as the stress rate increases.(4)An increase in the fault angle leads to denser cracking on the fault plane,with negligible cracking near the fault itself.The dominant crack orientation is approximately 90°,aligned with the vertical stress.
