Previous studies showed that an axisymmetric hub-initiated disturbance defined as partial surge may initiate the stall of a transonic compressor; to reveal the instability evolution under full-span incompressible flow...Previous studies showed that an axisymmetric hub-initiated disturbance defined as partial surge may initiate the stall of a transonic compressor; to reveal the instability evolution under full-span incompressible flow for different levels of hub loading and B parameter, an experimental investigation is conducted on a single-stage low-speed compressor. Experimental results show that under a uniform inflow condition without inlet flow distortion, a modal-type stall inception dominates in this low-speed compressor. When an inlet screen introducing hub distortion is used to increase the hub loading, a compressor stall is initiated by a modal wave, but large disturbances are present in the hub region before the compressor stall, which become stronger as the hub loading increases. Under high hub loading and large B parameter（implemented by adding hub distortion through an inlet screen and enlarging the outlet plenum volume, respectively）, a compressor stall is triggered by an axisymmetric hub-initiated disturbance, which is much different from the modal-like disturbances. The beginning of this axisymmetric disturbance may be captured over 800 rotor revolutions prior to the onset of stall, and the amplitude grows with time. The disturbance is hub-initiated because the disturbance signal at the hub is detected much earlier than that at the tip; meanwhile, the frequency of this axisymmetric disturbance changes with the length of the inlet duct. The characteristics of instability evolution in the low-speed compressor are also compared with those in a transonic compressor.展开更多
Expanding photovoltaic(PV)resources in rural-grid areas is an essential means to augment the share of solar energy in the energy landscape,aligning with the“carbon peaking and carbon neutrality”objectives.However,ru...Expanding photovoltaic(PV)resources in rural-grid areas is an essential means to augment the share of solar energy in the energy landscape,aligning with the“carbon peaking and carbon neutrality”objectives.However,rural power grids often lack digitalization;thus,the load distribution within these areas is not fully known.This hinders the calculation of the available PV capacity and deduction of node voltages.This study proposes a load-distribution modeling approach based on remote-sensing image recognition in pursuit of a scientific framework for developing distributed PV resources in rural grid areas.First,houses in remote-sensing images are accurately recognized using deep-learning techniques based on the YOLOv5 model.The distribution of the houses is then used to estimate the load distribution in the grid area.Next,equally spaced and clustered distribution models are used to adaptively determine the location of the nodes and load power in the distribution lines.Finally,by calculating the connectivity matrix of the nodes,a minimum spanning tree is extracted,the topology of the network is constructed,and the node parameters of the load-distribution model are calculated.The proposed scheme is implemented in a software package and its efficacy is demonstrated by analyzing typical remote-sensing images of rural grid areas.The results underscore the ability of the proposed approach to effectively discern the distribution-line structure and compute the node parameters,thereby offering vital support for determining PV access capability.展开更多
The dynamic load distribution within in-service axlebox bearings of high-speed trains is crucial for the fatigue reliability assessment and forward design of axlebox bearings. This paper presents an in situ measuremen...The dynamic load distribution within in-service axlebox bearings of high-speed trains is crucial for the fatigue reliability assessment and forward design of axlebox bearings. This paper presents an in situ measurement of the dynamic load distribution in the four rows of two axlebox bearings on a bogie wheelset of a high-speed train under polygonal wheel–rail excitation. The measurement employed an improved strain-based method to measure the dynamic radial load distribution of roller bearings. The four rows of two axlebox bearings on a wheelset exhibited different ranges of loaded zones and different means of distributed loads. Besides, the mean value and standard deviation of measured roller–raceway contact loads showed non-monotonic variations with the frequency of wheel–rail excitation. The fatigue life of the four bearing rows under polygonal wheel–rail excitation was quantitatively predicted by compiling the measured roller–raceway contact load spectra of the most loaded position and considering the load spectra as input.展开更多
This study presents a closed-form solution for central stress,a semi-analytical model,and a modified anisotropic semi-analytical model to efficiently calculate the forcefrequency coefficients(FFCs)of square quartz cry...This study presents a closed-form solution for central stress,a semi-analytical model,and a modified anisotropic semi-analytical model to efficiently calculate the forcefrequency coefficients(FFCs)of square quartz crystal resonators(QCRs)with different side lengths and azimuth angles under eccentrically concentrated and distributed loads.The semi-analytical model is validated by comparisons between the experimental results and the nonlinear finite element method(FEM)simulation results.Based on the semi-analytical model for the FFC and nonlinear FEM simulations,the FFC variations of square QCRs under external loads and the related mechanisms are investigated.Among the initial stresses caused by external loads,the central stress parallel to the xcrystallographic axis is the primary factor influencing the FFC of quartz.Our findings can provide practical tools for calculating the FFC,and help the design and development of square quartz force sensors.展开更多
Load distribution is a key technology in strip hot rolling process, which influences the coil＇s mierostrueture and performance. Currently, Newton-Raphson algorithm is applied to load distribution of hot tandem mills ...Load distribution is a key technology in strip hot rolling process, which influences the coil＇s mierostrueture and performance. Currently, Newton-Raphson algorithm is applied to load distribution of hot tandem mills in many hot rolling plants and has some serious defects such as having a strict restriction on initial iterative calculation value and requiring coefficient matrix of nonlinear equations to be nonsingular. To eliminate these defects and improve the online performance of the process control computer, Newton descendent numeric algorithm is introduced to this field to widen the initial value range and a new model named error conversion algorithm is put forth to deal with special conditions when the coefficient matrix is singular. Furthermore, considering the characteristics of load distribution, a condition of strip thickness distribution abnormality and corresponding solutions are provided which ensure that rolling parameters can be calculated normally. Simulation results show that the improved algorithm has overcome the defects of the Newton-Raphson algorithm and is suitable for online application.展开更多
Load distribution is a key technology in hot strip rolling process, which directly influences strip product quality. A multi-objective load distribution model, which takes into account the rolling force margin balance...Load distribution is a key technology in hot strip rolling process, which directly influences strip product quality. A multi-objective load distribution model, which takes into account the rolling force margin balance, roll wear ratio and strip shape control, is presented. To avoid the selection of weight coefficients encountered in single objective optimization, a multi-objective differential evolutionary algorithm, called MaximinDE, is proposed to solve this model. The experimental results based on practical production data indicate that MaximinDE can obtain a good pareto-optimal solution set, which consists of a series of alternative solutions to load distribution. Decision-makers can select a trade-off solution from the pareto-optimal solution set based on their experience or the importance of ob- iectives. In comparison with the empirical load distribution solution, the trade-off solution can achieve a better per- formance, which demonstrates the effectiveness of the multi-objective load distribution optimization. Moreover, the conflicting relationship among different objectives can be also found, which is another advantage of multi-objective load distribution optimization.展开更多
Load distribution is the foundation of shape control and gauge control, in which it is necessary to take into account the shape control ability of TCM （tandem cold mill） for strip shape and gauge quality. First, the...Load distribution is the foundation of shape control and gauge control, in which it is necessary to take into account the shape control ability of TCM （tandem cold mill） for strip shape and gauge quality. First, the objective function of generalized shape and gauge decoupling load distribution optimization was established, which considered the rolling force characteristics of the first and last stands in TCM, the relative power, and the TCM shape control ability. Then, IGA （immune genetic algorithm） was used to accomplish this multi-objective load distribution optimization for TCM. After simulation and comparison with the practical load distribution strategy in one tandem cold mill, general- ized shape and gauge decoupling load distribution optimization on the basis of IGA approved good ability of optimizing shape control and gauge control simultaneously.展开更多
Voltage profiles of feeders with the connection of distributed generations(DGs) were investigated.A unified typical load distribution model was established.Based on this model,exact expressions of feeder voltage profi...Voltage profiles of feeders with the connection of distributed generations(DGs) were investigated.A unified typical load distribution model was established.Based on this model,exact expressions of feeder voltage profile with single and double DGs were derived and used to analyze the impact of DG's location and capacity on the voltage profile quantitatively.Then,a general formula of the voltage profile was derived.The limitation of single DG and necessity of multiple DGs for voltage regulation were also discussed.Through the simulation,voltage profiles of feeders with single and double DGs were compared.The voltage excursion rate is 7.40% for only one DG,while 2.48% and 2.36% for double DGs.It is shown that the feeder voltage can be retained in a more appropriate range with multiple DGs than with only one DG.Distributing the total capacity of DGs is better than concentrating it at one point.展开更多
Regularity of longitudinal load distribution on gear tooth when tooth faces are contacted uniformly and when only tooth ends are contacted, and influence on distribution exerted by longitudinal correction and flexible...Regularity of longitudinal load distribution on gear tooth when tooth faces are contacted uniformly and when only tooth ends are contacted, and influence on distribution exerted by longitudinal correction and flexible gear structure, are studied in the paper with method of finite element calculation combined with experiment. Research shows that load concentration exists on the conditions of uniform contact or one-end contact, and in the later case the stress nonuniformity factor on root is 1.5 to 2.0 times larger than in the former case. It also verifies that longitudinal correction and increased flexibility of gear structure are effective to improve longitudinal load distribution.展开更多
The boundary between the near and far fields is generally defined as the distance from the vibration source beyond which ground vibrations are mainly dominated by Rayleigh waves. It is closely related to the type of v...The boundary between the near and far fields is generally defined as the distance from the vibration source beyond which ground vibrations are mainly dominated by Rayleigh waves. It is closely related to the type of vibration source and the soil properties. Based on the solutions of the Lamb＇s problem, the boundary at the surface between the near and far fields of ground vibration was investigated for a harmonic vertical concentrated load and an infinite line load at the surface of a visco-elastic half-space. Particularly, the variation of the boundary with the material damping was investigated for both cases. The results indicate that the material damping slightly contributes to the attenuation of vibrations in the near-source region, but significantly reduces the vibrations in the region that is at some distance away from the source. When taking the material damping into consideration, the boundary between the near and far fields tends to move towards the vibration source. Compared with the vibrations caused by a concentrated load, the vibrations induced by an infinite line load can affect a larger range of the surrounding environment, and they attenuate more slowly. This means the boundary between the near field and far field should move fitrther away from the source. Finally, the boundaries are defined in terms of R-wave length （2R） and Poisson ratio of the ground （o）. For the case of a point load, the boundary is located at the distance of （5.0-6.0）2R for v≤0.30 and at the distance of （2.0--3.0）2R for v≥0.35. For the case of an infinite line load, the boundary is located at the distance （5.5-6.5）2rt for v≤0.30 and at the distance （2.5--3.5）2R for v≥0.35.展开更多
Based on the Reissner assumptions, this paper is concerned with the bending analy- sis of simply supported sandwich plates with functionally graded core and orthotropic face sheets subjected to transverse distributed ...Based on the Reissner assumptions, this paper is concerned with the bending analy- sis of simply supported sandwich plates with functionally graded core and orthotropic face sheets subjected to transverse distributed loadings. First, the expressions of the displacements, stresses and internal forces of the sandwich plate are presented according to the constitutive relations and stress states of the core and face sheets. Then, the solutions of bending equilibrium equa- tions are derived by expanding the deflection w, transverse shearing forces Q~ and Qv with double trigonometric series that satisfy the simply supported boundary conditions. Finally, the proposed solution is validated by comparing the results with available elasticity solutions for a square sand- wich plate with an isotropie core and finite element simulations for one with functionally graded core. The Young＇s modulus of the functionally graded core is assumed to be graded by a power law distribution of volume fractions of the constituents, and the Poisson＇s ratio is held constant. And the effects of the core＇s top-bottom Young＇s modulus ratio A and volume fraction exponent no on the variation of the displacements of the functionally graded sandwich plate are also examined.展开更多
It is of great significance to reasonably distribute the slung load to each helicopter while considering difference in power consumption,relative position and interaction comprehensively.Therefore,the load distributio...It is of great significance to reasonably distribute the slung load to each helicopter while considering difference in power consumption,relative position and interaction comprehensively.Therefore,the load distribution strategy based on power consumption and robust adaptive game control is proposed in this paper.The study is on a"2-lead"multi-lift system of four tandem heli-copters carrying a load cooperatively.First,based on the hierarchical control,the load distribution problem is divided into two parts:the calculation of expected cable force and the calculation of the anti-disturbance cable force.Then,aimed at minimizing the maximum equivalent power of heli-copter,an optimization problem is set up to calculate the expected cable force.Specially,the agent power model is trained by BP neural network,the safe distance constraint between helicopters is set to 2.5 rotor diameters to reduce aerodynamic interference,and the helicopters with different perfor-mance can be considered by introducing the equivalent power factor into the objective function.Next,considering the difference and interaction between helicopters,the robust adaptive differen-tial game control is proposed to calculate the anti-disturbance cable force.Particularly,to solve the coupled Hamiltonian equations,an adaptive solving method for value function is proposed,and its stability is proved in the sense of Lyapunov.The simulation results indicate that the proposed load distribution method based on power consumption is applicable to the entire flight trajectory even there are differences between helicopters.The game control can consider interaction between heli-copters,can deal with different objective functions,and has strong robustness and small steady-state error.Based on the entire strategy,the cable force can be reasonably allocated so as to resist disturbance and improve the flight performance of the whole system.展开更多
A new method of establishing rolling load distribution model was developed by online intelligent information-processing technology for plate rolling. The model combines knowledge model and mathematical model with usin...A new method of establishing rolling load distribution model was developed by online intelligent information-processing technology for plate rolling. The model combines knowledge model and mathematical model with using knowledge discovery in database （KDD） and data mining （DM） as the start. The online maintenance and optimization of the load model are realized. The effectiveness of this new method was testified by offline simulation and online application.展开更多
A dynamic analysis approcach to investigate the state of load distribution among contact bearings of double circular are belical gears is proposed and a computer program is developed for calculating the factor of iced...A dynamic analysis approcach to investigate the state of load distribution among contact bearings of double circular are belical gears is proposed and a computer program is developed for calculating the factor of iced distribution based on the theory of W-N gears. The changing situations of load distribution among contact bearings of the gears influenced by main issues are analyzed by a series of parametric studies.展开更多
A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of dr...A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of drive current rise-time and initial load density distribution by using the typical experimental parameters of tungsten wire-array Z- pinch on the Qiangguang-I generator. The numerical results show that as the drive current rise-time is shortened, x-ray radiation peak power, energy, peak plasma density and peak ion temperature increase approximately linearly, but among them the x-ray radiation peak power increases more quickly. As the initial plasma density distribution in the radial direction becomes gradually flattened, the peak radiation power and the peak ion-temperature almost exponentially increase, while the radiation energy and the peak plasma density change only a little. The main effect of shortening drive current rise-time is to enhance compression of plasma, and the effect of flattening initial load density distribution in the radial direction is to raise the plasma temperature. Both of the approaches elevate the x-ray peak radiation power展开更多
In this paper, primary manufacturing and assembling errors of three-ring gear reducer （TRGR） are analyzed. TRGR is a new transmission type whose eccentric phase difference between middle ring plate and side ring pla...In this paper, primary manufacturing and assembling errors of three-ring gear reducer （TRGR） are analyzed. TRGR is a new transmission type whose eccentric phase difference between middle ring plate and side ring plates is 120°, Its mass of middle ring plate is equal to that of side ring plate or 180°, and its inass of middle ring plate is twice of that of side ring plate, which affects load distribution between ring plates. The primary manufacturing and assembling errors include eccentric error of eccentric sheath E111, internal gear plate E1 and output external gear E11. A new theoretical method is presented in this paper, which converts load on ring plates into the dedendum bending stress of ring plate to calculate load distribution coefficient （ LDC ）, by means of gap element method （GEM）, one of finite element method （FEM）. The theoretical calculation and experimental study, which measures ring plate dedendum bending stress by means of sticking strain gauges on the dedendum of middle ring plate internal gear and side ring plate internal gears, are presented. The theoretical calculation and comparison with experiment result of LDC are implemented an two kinds of three-ring gear reducers whose eccentric phase difference between eccentric sheaths is 120° and 180°respectively. The research indicates that the result of theoretical calculation is consistent with that of experimental study. That is to say, the theoretical calculation method is feasible.展开更多
At present,the large-scale access to electric vehicles(EVs)is exerting considerable pressure on the distribution network.Hence,it is particularly important to analyze the capacity of the distribution network to accomm...At present,the large-scale access to electric vehicles(EVs)is exerting considerable pressure on the distribution network.Hence,it is particularly important to analyze the capacity of the distribution network to accommodate EVs.To this end,we propose a method for analyzing the EV capacity of the distribution network by considering the composition of the conventional load.First,the analysis and pretreatment methods for the distribution network architecture and conventional load are proposed.Second,the charging behavior of an EVis simulated by combining the Monte Carlo method and the trip chain theory.After obtaining the temporal and spatial distribution of the EV charging load,themethod of distribution according to the proportion of the same type of conventional load among the nodes is adopted to integrate the EV charging load with the conventional load of the distribution network.By adjusting the EV ownership,the EV capacity in the distribution network is analyzed and solved on the basis of the following indices:node voltage,branch current,and transformer capacity.Finally,by considering the 10-kV distribution network in some areas of an actual city as an example,we show that the proposed analysis method can obtain a more reasonable number of EVs to be accommodated in the distribution network.展开更多
In ultra-dense networks(UDN),multiple association can be regarded as a user-centric pattern in which a user can be served by multiple base stations(BSs).The data rate and quality of service can be improved.However,BSs...In ultra-dense networks(UDN),multiple association can be regarded as a user-centric pattern in which a user can be served by multiple base stations(BSs).The data rate and quality of service can be improved.However,BSs in user-centric paradigm are required to serve more users due to this multiple association scheme.The improvement of system performance may be limited by the improving load of BSs.In this letter,we develope an analytical framework for the load distribution of BSs in heterogeneous user-centric UDN.Based on open loop power control(OLPC),a user-centric scheme is considered in which the clustered serving BSs can provide given signal to interference plus noise ratio(SINR)for any typical user.As for any BS in different tiers,by leveraging stochastic geometry,we derive the Probability Mass Function(PMF)of the number of the served users,the Cumulative Distribution Function(CDF)of total power consumption,and the CDF bounds of downlink sum data rate.The accuracy of the theoretical analysis is validated by numerical simulations,and the effect the system parameters on the load of BSs is also presented.展开更多
The jacking pinions and rack chocks of the fixation system of a jack-up sustain tremendous load in the elevated condition, especially when there exists a remarkable non-uniformity of the load distribution. Failures of...The jacking pinions and rack chocks of the fixation system of a jack-up sustain tremendous load in the elevated condition, especially when there exists a remarkable non-uniformity of the load distribution. Failures of these structural components may lead to disastrous consequence of the jack-up. Despite the importance of these components, it is difficult to give an accurate prediction of the load distribution on these components in engineering application due to the complex nonlinear interaction mechanism, which is influenced by the relative stiffness of the components, leg-guide clearance and backlash. Previous studies mainly focus on the global performance of the jack-up and pay little attention to the load distribution on the pinions and chocks. The strength of the jacking system is often guaranteed by the manufacturer for an estimate load level, which brings in uncertainty to the safety of the jack-up. The characteristics of the hull-leg interaction are discussed in this paper, and a simplified method using gap elements is proposed. The nonlinear structural analyses are carried out for a specific jack-up using the proposed method and the three-dimensional finite element method(FEM) with contact algorithm. The proposed method is proved accurate and effective for the engineering application. The characteristics of the load distribution of the specific jack-up are discussed, and the conclusions are presented.展开更多
Redundantly actuated parallel manipulators have the advantage of enhancing load-carrying capability over their non-redundant ones, however they also cause the problem of uneven load distribution and need a high requir...Redundantly actuated parallel manipulators have the advantage of enhancing load-carrying capability over their non-redundant ones, however they also cause the problem of uneven load distribution and need a high requirement for the control system. This paper presents a 2-RPR/RP planar redundantly actuated parallel manipulator which can self-coordinate the distribution of external loads. This capability is realized by an appropriate design of the moving platform to make the manipulator stable at equilibrium position. The stability is proved by the theorem of direct Lyapunov method in classical mechanics. The numerical simulations are conducted to validate the stable capability by means of the observation of potential energies and phase planes. This paper offers an alternative way to design a redundantly actuated manipulator with the capability of self-coordinating the load distribution to actuations, such that parts of the controlling work are assigned to the manipulator itself by its own structure and only a little work remains to the control system.展开更多
基金the supports of the National Natural Science Foundation of China (Nos.51636001 and 51706008)Aeronautics Power Foundation of China (No.6141B090315)China Postdoctoral Science Foundation (No.2017M610742)
文摘Previous studies showed that an axisymmetric hub-initiated disturbance defined as partial surge may initiate the stall of a transonic compressor; to reveal the instability evolution under full-span incompressible flow for different levels of hub loading and B parameter, an experimental investigation is conducted on a single-stage low-speed compressor. Experimental results show that under a uniform inflow condition without inlet flow distortion, a modal-type stall inception dominates in this low-speed compressor. When an inlet screen introducing hub distortion is used to increase the hub loading, a compressor stall is initiated by a modal wave, but large disturbances are present in the hub region before the compressor stall, which become stronger as the hub loading increases. Under high hub loading and large B parameter（implemented by adding hub distortion through an inlet screen and enlarging the outlet plenum volume, respectively）, a compressor stall is triggered by an axisymmetric hub-initiated disturbance, which is much different from the modal-like disturbances. The beginning of this axisymmetric disturbance may be captured over 800 rotor revolutions prior to the onset of stall, and the amplitude grows with time. The disturbance is hub-initiated because the disturbance signal at the hub is detected much earlier than that at the tip; meanwhile, the frequency of this axisymmetric disturbance changes with the length of the inlet duct. The characteristics of instability evolution in the low-speed compressor are also compared with those in a transonic compressor.
基金supported by the State Grid Science&Technology Project of China(5400-202224153A-1-1-ZN).
文摘Expanding photovoltaic(PV)resources in rural-grid areas is an essential means to augment the share of solar energy in the energy landscape,aligning with the“carbon peaking and carbon neutrality”objectives.However,rural power grids often lack digitalization;thus,the load distribution within these areas is not fully known.This hinders the calculation of the available PV capacity and deduction of node voltages.This study proposes a load-distribution modeling approach based on remote-sensing image recognition in pursuit of a scientific framework for developing distributed PV resources in rural grid areas.First,houses in remote-sensing images are accurately recognized using deep-learning techniques based on the YOLOv5 model.The distribution of the houses is then used to estimate the load distribution in the grid area.Next,equally spaced and clustered distribution models are used to adaptively determine the location of the nodes and load power in the distribution lines.Finally,by calculating the connectivity matrix of the nodes,a minimum spanning tree is extracted,the topology of the network is constructed,and the node parameters of the load-distribution model are calculated.The proposed scheme is implemented in a software package and its efficacy is demonstrated by analyzing typical remote-sensing images of rural grid areas.The results underscore the ability of the proposed approach to effectively discern the distribution-line structure and compute the node parameters,thereby offering vital support for determining PV access capability.
基金supported by the National Natural Science Foundation of China (Grant No. 12302238)the National Key Research and Development Program of China (Grant Nos. 2021YFB3400701, 2022YFB3402904)。
文摘The dynamic load distribution within in-service axlebox bearings of high-speed trains is crucial for the fatigue reliability assessment and forward design of axlebox bearings. This paper presents an in situ measurement of the dynamic load distribution in the four rows of two axlebox bearings on a bogie wheelset of a high-speed train under polygonal wheel–rail excitation. The measurement employed an improved strain-based method to measure the dynamic radial load distribution of roller bearings. The four rows of two axlebox bearings on a wheelset exhibited different ranges of loaded zones and different means of distributed loads. Besides, the mean value and standard deviation of measured roller–raceway contact loads showed non-monotonic variations with the frequency of wheel–rail excitation. The fatigue life of the four bearing rows under polygonal wheel–rail excitation was quantitatively predicted by compiling the measured roller–raceway contact load spectra of the most loaded position and considering the load spectra as input.
基金supported by the Ningbo Youth Science and Technology Innovation Leading Talents of China(No.2023QL020)the Ningbo Science and Technology Major of China(No.2022Z015)the K.C.Wong Magana Fund through Ningbo University。
文摘This study presents a closed-form solution for central stress,a semi-analytical model,and a modified anisotropic semi-analytical model to efficiently calculate the forcefrequency coefficients(FFCs)of square quartz crystal resonators(QCRs)with different side lengths and azimuth angles under eccentrically concentrated and distributed loads.The semi-analytical model is validated by comparisons between the experimental results and the nonlinear finite element method(FEM)simulation results.Based on the semi-analytical model for the FFC and nonlinear FEM simulations,the FFC variations of square QCRs under external loads and the related mechanisms are investigated.Among the initial stresses caused by external loads,the central stress parallel to the xcrystallographic axis is the primary factor influencing the FFC of quartz.Our findings can provide practical tools for calculating the FFC,and help the design and development of square quartz force sensors.
基金Item Sponsored by National Natural Science Foundation of China (50504007)
文摘Load distribution is a key technology in strip hot rolling process, which influences the coil＇s mierostrueture and performance. Currently, Newton-Raphson algorithm is applied to load distribution of hot tandem mills in many hot rolling plants and has some serious defects such as having a strict restriction on initial iterative calculation value and requiring coefficient matrix of nonlinear equations to be nonsingular. To eliminate these defects and improve the online performance of the process control computer, Newton descendent numeric algorithm is introduced to this field to widen the initial value range and a new model named error conversion algorithm is put forth to deal with special conditions when the coefficient matrix is singular. Furthermore, considering the characteristics of load distribution, a condition of strip thickness distribution abnormality and corresponding solutions are provided which ensure that rolling parameters can be calculated normally. Simulation results show that the improved algorithm has overcome the defects of the Newton-Raphson algorithm and is suitable for online application.
基金Item Sponsored by National Natural Science Foundation of China(50974039)
文摘Load distribution is a key technology in hot strip rolling process, which directly influences strip product quality. A multi-objective load distribution model, which takes into account the rolling force margin balance, roll wear ratio and strip shape control, is presented. To avoid the selection of weight coefficients encountered in single objective optimization, a multi-objective differential evolutionary algorithm, called MaximinDE, is proposed to solve this model. The experimental results based on practical production data indicate that MaximinDE can obtain a good pareto-optimal solution set, which consists of a series of alternative solutions to load distribution. Decision-makers can select a trade-off solution from the pareto-optimal solution set based on their experience or the importance of ob- iectives. In comparison with the empirical load distribution solution, the trade-off solution can achieve a better per- formance, which demonstrates the effectiveness of the multi-objective load distribution optimization. Moreover, the conflicting relationship among different objectives can be also found, which is another advantage of multi-objective load distribution optimization.
基金Item Sponsored by National Significant Technology and Equipment Research Project of China (ZZ02-13B-03)
文摘Load distribution is the foundation of shape control and gauge control, in which it is necessary to take into account the shape control ability of TCM （tandem cold mill） for strip shape and gauge quality. First, the objective function of generalized shape and gauge decoupling load distribution optimization was established, which considered the rolling force characteristics of the first and last stands in TCM, the relative power, and the TCM shape control ability. Then, IGA （immune genetic algorithm） was used to accomplish this multi-objective load distribution optimization for TCM. After simulation and comparison with the practical load distribution strategy in one tandem cold mill, general- ized shape and gauge decoupling load distribution optimization on the basis of IGA approved good ability of optimizing shape control and gauge control simultaneously.
基金Projects(60904101,60972164) supported by the National Natural Science Foundation of ChinaProject(N090404009) supported by the Fundamental Research Funds for the Central UniversitiesProject(20090461187) supported by China Postdoctoral Science Foundation
文摘Voltage profiles of feeders with the connection of distributed generations(DGs) were investigated.A unified typical load distribution model was established.Based on this model,exact expressions of feeder voltage profile with single and double DGs were derived and used to analyze the impact of DG's location and capacity on the voltage profile quantitatively.Then,a general formula of the voltage profile was derived.The limitation of single DG and necessity of multiple DGs for voltage regulation were also discussed.Through the simulation,voltage profiles of feeders with single and double DGs were compared.The voltage excursion rate is 7.40% for only one DG,while 2.48% and 2.36% for double DGs.It is shown that the feeder voltage can be retained in a more appropriate range with multiple DGs than with only one DG.Distributing the total capacity of DGs is better than concentrating it at one point.
文摘Regularity of longitudinal load distribution on gear tooth when tooth faces are contacted uniformly and when only tooth ends are contacted, and influence on distribution exerted by longitudinal correction and flexible gear structure, are studied in the paper with method of finite element calculation combined with experiment. Research shows that load concentration exists on the conditions of uniform contact or one-end contact, and in the later case the stress nonuniformity factor on root is 1.5 to 2.0 times larger than in the former case. It also verifies that longitudinal correction and increased flexibility of gear structure are effective to improve longitudinal load distribution.
基金Project(51178342)supported by the National Natural Science Foundation of ChinaProject(KLE-TJGE-C1301)supported by the Key Laboratory of Geotechnical and Underground Engineering of Ministry of Education(Tongji University)under the International Cooperation and Exchange Program,China
文摘The boundary between the near and far fields is generally defined as the distance from the vibration source beyond which ground vibrations are mainly dominated by Rayleigh waves. It is closely related to the type of vibration source and the soil properties. Based on the solutions of the Lamb＇s problem, the boundary at the surface between the near and far fields of ground vibration was investigated for a harmonic vertical concentrated load and an infinite line load at the surface of a visco-elastic half-space. Particularly, the variation of the boundary with the material damping was investigated for both cases. The results indicate that the material damping slightly contributes to the attenuation of vibrations in the near-source region, but significantly reduces the vibrations in the region that is at some distance away from the source. When taking the material damping into consideration, the boundary between the near and far fields tends to move towards the vibration source. Compared with the vibrations caused by a concentrated load, the vibrations induced by an infinite line load can affect a larger range of the surrounding environment, and they attenuate more slowly. This means the boundary between the near field and far field should move fitrther away from the source. Finally, the boundaries are defined in terms of R-wave length （2R） and Poisson ratio of the ground （o）. For the case of a point load, the boundary is located at the distance of （5.0-6.0）2R for v≤0.30 and at the distance of （2.0--3.0）2R for v≥0.35. For the case of an infinite line load, the boundary is located at the distance （5.5-6.5）2rt for v≤0.30 and at the distance （2.5--3.5）2R for v≥0.35.
基金Project supported by the National Natural Science Foundation of China(No. 50979110)
文摘Based on the Reissner assumptions, this paper is concerned with the bending analy- sis of simply supported sandwich plates with functionally graded core and orthotropic face sheets subjected to transverse distributed loadings. First, the expressions of the displacements, stresses and internal forces of the sandwich plate are presented according to the constitutive relations and stress states of the core and face sheets. Then, the solutions of bending equilibrium equa- tions are derived by expanding the deflection w, transverse shearing forces Q~ and Qv with double trigonometric series that satisfy the simply supported boundary conditions. Finally, the proposed solution is validated by comparing the results with available elasticity solutions for a square sand- wich plate with an isotropie core and finite element simulations for one with functionally graded core. The Young＇s modulus of the functionally graded core is assumed to be graded by a power law distribution of volume fractions of the constituents, and the Poisson＇s ratio is held constant. And the effects of the core＇s top-bottom Young＇s modulus ratio A and volume fraction exponent no on the variation of the displacements of the functionally graded sandwich plate are also examined.
文摘It is of great significance to reasonably distribute the slung load to each helicopter while considering difference in power consumption,relative position and interaction comprehensively.Therefore,the load distribution strategy based on power consumption and robust adaptive game control is proposed in this paper.The study is on a"2-lead"multi-lift system of four tandem heli-copters carrying a load cooperatively.First,based on the hierarchical control,the load distribution problem is divided into two parts:the calculation of expected cable force and the calculation of the anti-disturbance cable force.Then,aimed at minimizing the maximum equivalent power of heli-copter,an optimization problem is set up to calculate the expected cable force.Specially,the agent power model is trained by BP neural network,the safe distance constraint between helicopters is set to 2.5 rotor diameters to reduce aerodynamic interference,and the helicopters with different perfor-mance can be considered by introducing the equivalent power factor into the objective function.Next,considering the difference and interaction between helicopters,the robust adaptive differen-tial game control is proposed to calculate the anti-disturbance cable force.Particularly,to solve the coupled Hamiltonian equations,an adaptive solving method for value function is proposed,and its stability is proved in the sense of Lyapunov.The simulation results indicate that the proposed load distribution method based on power consumption is applicable to the entire flight trajectory even there are differences between helicopters.The game control can consider interaction between heli-copters,can deal with different objective functions,and has strong robustness and small steady-state error.Based on the entire strategy,the cable force can be reasonably allocated so as to resist disturbance and improve the flight performance of the whole system.
文摘A new method of establishing rolling load distribution model was developed by online intelligent information-processing technology for plate rolling. The model combines knowledge model and mathematical model with using knowledge discovery in database （KDD） and data mining （DM） as the start. The online maintenance and optimization of the load model are realized. The effectiveness of this new method was testified by offline simulation and online application.
文摘A dynamic analysis approcach to investigate the state of load distribution among contact bearings of double circular are belical gears is proposed and a computer program is developed for calculating the factor of iced distribution based on the theory of W-N gears. The changing situations of load distribution among contact bearings of the gears influenced by main issues are analyzed by a series of parametric studies.
基金Project supported by the National Natural Science Foundation of China （Grant No 10035020）.
文摘A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of drive current rise-time and initial load density distribution by using the typical experimental parameters of tungsten wire-array Z- pinch on the Qiangguang-I generator. The numerical results show that as the drive current rise-time is shortened, x-ray radiation peak power, energy, peak plasma density and peak ion temperature increase approximately linearly, but among them the x-ray radiation peak power increases more quickly. As the initial plasma density distribution in the radial direction becomes gradually flattened, the peak radiation power and the peak ion-temperature almost exponentially increase, while the radiation energy and the peak plasma density change only a little. The main effect of shortening drive current rise-time is to enhance compression of plasma, and the effect of flattening initial load density distribution in the radial direction is to raise the plasma temperature. Both of the approaches elevate the x-ray peak radiation power
基金Sponsored by the National Natural Science Foundation of China(Grant No.59575007).
文摘In this paper, primary manufacturing and assembling errors of three-ring gear reducer （TRGR） are analyzed. TRGR is a new transmission type whose eccentric phase difference between middle ring plate and side ring plates is 120°, Its mass of middle ring plate is equal to that of side ring plate or 180°, and its inass of middle ring plate is twice of that of side ring plate, which affects load distribution between ring plates. The primary manufacturing and assembling errors include eccentric error of eccentric sheath E111, internal gear plate E1 and output external gear E11. A new theoretical method is presented in this paper, which converts load on ring plates into the dedendum bending stress of ring plate to calculate load distribution coefficient （ LDC ）, by means of gap element method （GEM）, one of finite element method （FEM）. The theoretical calculation and experimental study, which measures ring plate dedendum bending stress by means of sticking strain gauges on the dedendum of middle ring plate internal gear and side ring plate internal gears, are presented. The theoretical calculation and comparison with experiment result of LDC are implemented an two kinds of three-ring gear reducers whose eccentric phase difference between eccentric sheaths is 120° and 180°respectively. The research indicates that the result of theoretical calculation is consistent with that of experimental study. That is to say, the theoretical calculation method is feasible.
基金supported by the Science and Technology Project of Zhangjiakou Power Supply Company of State Grid Jibei Co.,Ltd.(SGJBZJ00YJJS2001096).
文摘At present,the large-scale access to electric vehicles(EVs)is exerting considerable pressure on the distribution network.Hence,it is particularly important to analyze the capacity of the distribution network to accommodate EVs.To this end,we propose a method for analyzing the EV capacity of the distribution network by considering the composition of the conventional load.First,the analysis and pretreatment methods for the distribution network architecture and conventional load are proposed.Second,the charging behavior of an EVis simulated by combining the Monte Carlo method and the trip chain theory.After obtaining the temporal and spatial distribution of the EV charging load,themethod of distribution according to the proportion of the same type of conventional load among the nodes is adopted to integrate the EV charging load with the conventional load of the distribution network.By adjusting the EV ownership,the EV capacity in the distribution network is analyzed and solved on the basis of the following indices:node voltage,branch current,and transformer capacity.Finally,by considering the 10-kV distribution network in some areas of an actual city as an example,we show that the proposed analysis method can obtain a more reasonable number of EVs to be accommodated in the distribution network.
基金supported by National Natural Science Foundation of China (No. 61971161)Foundation of Science and Technology on Communication Networks Laboratory (No.6142104190410)Heilongjiang Touyan Team(No. HITTY20190009)
文摘In ultra-dense networks(UDN),multiple association can be regarded as a user-centric pattern in which a user can be served by multiple base stations(BSs).The data rate and quality of service can be improved.However,BSs in user-centric paradigm are required to serve more users due to this multiple association scheme.The improvement of system performance may be limited by the improving load of BSs.In this letter,we develope an analytical framework for the load distribution of BSs in heterogeneous user-centric UDN.Based on open loop power control(OLPC),a user-centric scheme is considered in which the clustered serving BSs can provide given signal to interference plus noise ratio(SINR)for any typical user.As for any BS in different tiers,by leveraging stochastic geometry,we derive the Probability Mass Function(PMF)of the number of the served users,the Cumulative Distribution Function(CDF)of total power consumption,and the CDF bounds of downlink sum data rate.The accuracy of the theoretical analysis is validated by numerical simulations,and the effect the system parameters on the load of BSs is also presented.
文摘The jacking pinions and rack chocks of the fixation system of a jack-up sustain tremendous load in the elevated condition, especially when there exists a remarkable non-uniformity of the load distribution. Failures of these structural components may lead to disastrous consequence of the jack-up. Despite the importance of these components, it is difficult to give an accurate prediction of the load distribution on these components in engineering application due to the complex nonlinear interaction mechanism, which is influenced by the relative stiffness of the components, leg-guide clearance and backlash. Previous studies mainly focus on the global performance of the jack-up and pay little attention to the load distribution on the pinions and chocks. The strength of the jacking system is often guaranteed by the manufacturer for an estimate load level, which brings in uncertainty to the safety of the jack-up. The characteristics of the hull-leg interaction are discussed in this paper, and a simplified method using gap elements is proposed. The nonlinear structural analyses are carried out for a specific jack-up using the proposed method and the three-dimensional finite element method(FEM) with contact algorithm. The proposed method is proved accurate and effective for the engineering application. The characteristics of the load distribution of the specific jack-up are discussed, and the conclusions are presented.
基金Supported by National Basic Research Program of China(973 Program,Grant No.2014CB046600)National Natural Science Foundation of China(Grant No.11472172)+1 种基金National Science Foundation for the Youth(Grant No.51305256)Specialized Research Fund for the Doctoral Program of Higher Education,China(Grant No.20130073110039)
文摘Redundantly actuated parallel manipulators have the advantage of enhancing load-carrying capability over their non-redundant ones, however they also cause the problem of uneven load distribution and need a high requirement for the control system. This paper presents a 2-RPR/RP planar redundantly actuated parallel manipulator which can self-coordinate the distribution of external loads. This capability is realized by an appropriate design of the moving platform to make the manipulator stable at equilibrium position. The stability is proved by the theorem of direct Lyapunov method in classical mechanics. The numerical simulations are conducted to validate the stable capability by means of the observation of potential energies and phase planes. This paper offers an alternative way to design a redundantly actuated manipulator with the capability of self-coordinating the load distribution to actuations, such that parts of the controlling work are assigned to the manipulator itself by its own structure and only a little work remains to the control system.
