A356/6061 bimetallic specimens were prepared by liquid-solid compound casting.The effects of various casting conditions on the interfacial microstructure and mechanical properties of the bimetallic specimens were stud...A356/6061 bimetallic specimens were prepared by liquid-solid compound casting.The effects of various casting conditions on the interfacial microstructure and mechanical properties of the bimetallic specimens were studied.Results demonstrate that a combination of chemical zinc deposition and electroplating can create a dense protective layer on the surface of the 6061 aluminum bar,achieving complete metallurgical bonding at the bimetallic interface.The interfacial microstructure is primarily characterized by equiaxed grain formation,with eutectic silicon distributed along the grain boundaries.Notably,the thickness of the zinc plating layer does not significantly influence the microstructure of the interface transition layer.Pouring temperature is critical for establishing metallurgical bonding at the bimetallic interface,with the thickness of the transition layer increasing as the pouring temperature rises.The hardness of the bimetallic composite interface falls between the hardness values of the two constituent materials.While the thickness of the galvanized layer has a minimal effect on interfacial shear strength,there is a slight decrease in shear strength with increasing pouring temperature,with a maximum value recorded at 68 MPa.展开更多
The liquid-solid compound casting technology was used to produce the AZ91D/0Cr19Ni9 bimetal composite without and with hot dipping aluminium, respectively. The influences of Al coating on microstructures and mechanica...The liquid-solid compound casting technology was used to produce the AZ91D/0Cr19Ni9 bimetal composite without and with hot dipping aluminium, respectively. The influences of Al coating on microstructures and mechanical properties of AZ91D/0Cr19Ni9 interface were investigated. The results showed that the mechanical bonding was obtained between AZ91D and bare steel 0Cr19Ni9 where a gap existed at the interface; the metallurgical bonding was formed between AZ91D and Al-coated 0Cr19Ni9, which could be divided into two different intermetallic layers: layer Ⅰ was mainly composed of α-Mg+β-Mg17Al12 eutectic structure and a small amount of MgAl2O4, and layer Ⅱ mainly comprised of Fe2Al5 intermetallic compound. Furthermore, the hardness value of interface was obviously higher than that of AZ91D matrix, and the average hardness values of layers Ⅰ and Ⅱ were HV 158 and HV 493, respectively. The shear strength of AZ91D/Al-coated 0Cr19Ni9 interface was higher than that of AZ91D/bare 0Cr19Ni9 interface, which confirmed that Al coating could improve the adhesive strength between AZ91D and 0Cr19Ni9 during liquid-solid compound casting process.展开更多
A Ni-P coating was deposited on Cu substrate by electroless plating and the Al/Cu bimetal was produced by solid？liquid compound casting technology. The microstructure, mechanical properties and conductivity of Al/Cu ...A Ni-P coating was deposited on Cu substrate by electroless plating and the Al/Cu bimetal was produced by solid？liquid compound casting technology. The microstructure, mechanical properties and conductivity of Al/Cu joints with different process parameters （bonding temperature and preheating time） were investigated. The results showed that intermetallics formed at the interface and the thickness and variety increased with the increase of bonding temperature and preheating time. The Ni？P interlayer functioned as a diffusion barrier and protective film which effectively reduced the formation of intermetallics. The shear strength and conductivity of Al/Cu bimetal were reduced by increasing the thickness of intermetallics. In particular, the detrimental effect of Al2Cu phase was more obvious compared with the others. The sample preheated at 780 ℃ for 150 s exhibited the maximum shear strength and conductivity of 49.8 MPa and 5.29×10^5 S/cm, respectively.展开更多
Al/steel bimetallic composites were prepared by compound casting,and the effects of the rotating magnetic field on the interfacial microstructure and shear property of bimetallic composite was investigated.The applica...Al/steel bimetallic composites were prepared by compound casting,and the effects of the rotating magnetic field on the interfacial microstructure and shear property of bimetallic composite was investigated.The application of rotating magnetic field refined the grain structure of the Al alloy matrix,changed the eutectic Si morphology from coarse lath to needle-like.The rotating magnetic field improved the temperature field and solute distribution of the Al alloy melt,enriched a layer of Si at the interface,and suppressed the growth of intermetallic compounds,the thickness of the interface layer decreased from 44.9μm to 22.8μm.The interfacial intermetallic compounds consisted ofη-Al_(5)Fe_(2),θ-Al_(13)Fe_(4),τ6-Al_(4.5)FeSi,τ_(5)-Al_(8)Fe_(2)Si andτ_(3)-Al_(2)FeSi,and the addition of the rotating magnetic field did not change phase composition.The rotating magnetic field improved the stress distribution within the interfacial intermetallic compounds,the presence of high-angle grain boundaries retarded crack extension,and the shear strength was enhanced from 31.27±3 MPa to 52.70±4 MPa.This work provides a feasible method for preparing Al/steel bimetallic composite with good bonding property.展开更多
The centrifugal casting of compound HSS/nodular cast iron roll collar was studied,and the factors affecting transition zone quality were analyzed.The pouring temperature and interval in pouring are the main factors af...The centrifugal casting of compound HSS/nodular cast iron roll collar was studied,and the factors affecting transition zone quality were analyzed.The pouring temperature and interval in pouring are the main factors affecting transition zone quality.By controlling process parameter and flux adding during casting,high quality roll collar was obtained.The cause,why in the casting of HSS part,segregation appears easily,was analyzed and the countermeasure eliminating segregation was put forward,the measure eliminating heat treatment crackling was also put forward.展开更多
Impact,friction and corrosion from the grinding balls and the grinding medium during the mineral processing result in liner breakage.Liner,made from Hadfield steel or alloyed steel,could not have served in wet grindin...Impact,friction and corrosion from the grinding balls and the grinding medium during the mineral processing result in liner breakage.Liner,made from Hadfield steel or alloyed steel,could not have served in wet grinding environment for more than ten months.Composite liner,made from HCWCI(high Cr white cast iron)and carbon steel,has been developed successfully with liquid-liquid composing process based on LFC(lost foam casting).The microstructure of composite was analyzed with optical microscope,SEM(scanning electron microscope)/EDX energy-dispersive X-ray and XRD(X-ray diffraction).According to micrograph,the combination region of two metals was staggered like dogtooth,no mixtures occurred between two liquid metals,and its interface presented excellent metallurgical bonding state.The results of mechanical property test show that,the hardness of HRC,the fracture toughness,and the bending strength are more than 61,16.5 J/cm2 and 1600 MPa,respectively.Comparison between liners made from bimetal composite and alloyed steel has also been investigated in industrial hematite ball mill.The results of eight months test in wet grinding environment prove that the service life of bimetal composite liner is three times as long as that of one made from alloyed steel.展开更多
Mg/Al bimetal combines the advantages of both aluminum and magnesium and has broad application prospects in automotive, aerospace,weapons, digital products and so on. The compound casting has the characteristics of lo...Mg/Al bimetal combines the advantages of both aluminum and magnesium and has broad application prospects in automotive, aerospace,weapons, digital products and so on. The compound casting has the characteristics of low cost, easy to achieve metallurgical combination and suitable for the preparation of complex bimetallic parts. However, bimetallic joint strength is low due to differences of physical properties between Al and Mg, oxide film on metallic surface and interfacial Al-Mg IMCs, which is closely related to the interfacial microstructure and properties. Therefore, how to control the interface of the bimetal to achieve performance enhancement is the focus and difficulty in this field. At present, there are mainly the following strengthening methods. First, the “zincate galvanizing” and “electrolytic polishing+anodic oxidation” technology were exert on the surface of Al alloy to remove and break the oxide film, which improved the wettability between Al and Mg. Second, the undesirable Al-Mg IMCs were reduce or elimination by adding the interlayers(Zn, Ni and Ni-Cu). Thirdly, the evolution process of interfacial microstructure was changed and fine strengthening phases were formed by adding Si element to Al alloy or rare earth element to Mg alloy. Fourthly, mechanical vibration and ultrasonic vibration were applied in the process of the filling and solidification to refine and homogenize the interfacial structure. Finally, some other methods, including secondary rolling, thermal modification, heat treatment and constructing exterior 3D morphology, also can be used to regulate the interfacial microstructure and compositions. The above strengthening methods can be used alone or in combination to achieve bimetallic strengthening. Finally, the future development direction of the Mg/Al bimetal is prospected, which provides some new ideas for the development and application of the Mg/Al bimetal.展开更多
The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects o...The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects of casting temperatures on microstructural evolution,properties,and fracture behaviors of Ni-coated TC4/AZ91D bimetals by the solid–liquid compound casting(SLCC).The scanning electron microscopy(SEM)and the energy dispersive spectroscopy(EDS)results showed that the interfacial zone mainly composed of nickel,Mg_(2)Ni and Mg-Al-Ni in the bimetals cast at 660℃.As the pouring temperature was increased to 750℃,the width of the interface zone,which mainly composed ofδ(Mg),Mg_(2)Ni,Mg-Al-Ni,Mg_(3)TiNi_(2) and Al_(3)Ni,gradually increased.The microhardness tests showed that the micro-hardness of the interface zone was smaller than that of TC4 substrate but larger than that of the cast AZ91D matrix.At the pouring temperature of 720℃,the Ni-coated TC4/AZ91D bimetals had the most typical homogeneous interface,which had granular Mg-Al-Ni ternary phase but no ribbon-like Al3Ni binary phase,and achieved the highest shear strength of 97.35MPa.Meanwhile,further fracture behavior analysis showed that most fracture failure of Ni-coated TC4/AZ91D bimetals occurred at the Mg_(2)Ni+δ(Mg)eutectic structure and Al_(3)Ni hard intermetallic.展开更多
To achieve Ti/Mg bimetallic composite with high strength and metallurgical bonding interface,Al interlayer and Zn/Al composite interlayer were used to prepare TC4/AZ91D bimetal composite with metallurgical bonding int...To achieve Ti/Mg bimetallic composite with high strength and metallurgical bonding interface,Al interlayer and Zn/Al composite interlayer were used to prepare TC4/AZ91D bimetal composite with metallurgical bonding interface by solid-liquid compound casting,respectively.Al interlayer was prepared on the surface of TC4 alloy by hot dipping,and Zn/Al composite interlayer was prepared by electroplating process.The results suggested that the phases across the interface were Al Ti andα(Al)+Mg_(21)(Al,Zn)_(17)when Zn/Al composite interlayer was used.When Al interlayer was used as interlayer,Al Mg Ti ternary structure and Al_(12)Mg_(17)+δ-Mg eutectic structure were the main phases at the interface.The shear strength of TC4/AZ91D bimetal with Zn/Al composite interlayer was much higher than that with pure Al interlayer,and the value of the shear strength was increased from 48.5 to 67.4 MPa.Thermodynamic models based on different compositions of the interface were established to explain the microstructure evolution of the interfacial zone.展开更多
In this work,a vibration was applied in the preparation of the Mg/Al bimetal by a novel compound casting in order to improve the mechanical properties of the Mg/Al bimetal,and the effect of the vibration on the interf...In this work,a vibration was applied in the preparation of the Mg/Al bimetal by a novel compound casting in order to improve the mechanical properties of the Mg/Al bimetal,and the effect of the vibration on the interfacial microstructure and mechanical properties of the Mg/Al bimetal was investigated.The results indicated that the vibration had a significant effect on the interfacial microstructure and mechanical properties of the Mg/Al bimetal,but it did not change the phase compositions of the interface,which was composed of layerⅠ(Al3Mg2+Mg2Si),layerⅡ(Al_(12)Mg_(17)+Mg_(2)Si)and layerⅢ(Al_(12)Mg_(17)/δ-Mg).Without vibration,the Mg_(2)Si phase with a needle-like morphology mainly aggregated in the layerⅡof the interface.After the application of the vibration,the SEM and EBSD analysis results showed that the Mg_(2)Si and Al3Mg2phases in the interface were obviously refined,and the distribution of the Mg_(2)Si became more uniform,due to the strong forced convection of the molten metal resulting from the vibration.The TEM analysis indicated that the interface between the A_(l3)Mg_(2) and Mg_(2)Si phases was non-coherent,suggesting the Mg_(2)Si particles cannot act as a heterogeneous nucleation base during the solidification process of the interface.Compared to the Mg/Al bimetal without vibration,the shear strength of the Mg/Al bimetal with vibration increased by about 50%from 31.7 MPa on average to 47.5 MPa,and the hardness of the layer I of the interface increased,and the hardness of the layerⅢdecreased.The fracture surface transformed from a flat fracture morphology without vibration to an irregular zigzag fracture morphology.展开更多
To improve the Al/Mg bimetallic interface,La was added into the Al/Mg bimetallic interface manufactured by a compound casting process.The effect of La addition on the microstructure,mechanical properties and fracture ...To improve the Al/Mg bimetallic interface,La was added into the Al/Mg bimetallic interface manufactured by a compound casting process.The effect of La addition on the microstructure,mechanical properties and fracture behavior of the Al/Mg bimetallic interface and the formation mechanism of the interface were studied in detail.Al_(11)La_(3),Al_(8)Mn_(4)La,Al_(20)Ti_(2)La,and other rare earth precipitates(RE precipitates)preferentially precipitated at the interface with La addition,while the number of the Al_(11)La_(3)and Al_(8)Mn_(4)La located in eutectic structure area(E area)gradually increased and aggregated in the interface with the increase of the La content.Besides,the matrix structure in different areas of the Al/Mg interface changed in different degrees,and the eutectic structure and primaryγ(Mg_(17)Al_(12))dendrites in the E area were refned,but the intermetallic compounds area(IMC area)had no obvious change.With the addition of the La,the interface was strengthened under the comprehensive effect of refnement strengthening and precipitation strengthening from the E area.When the La content increased to 1.0%,the shear strength of the Al/Mg bimetal reached the maximum of 51.54 MPa,which was 30.95%higher than the group without La addition.However,with the further increase of the La content,the large area aggregation of the Al_(11)La_(3)and Al_(8)Mn_(4)La occurred in the interface,leading to the separation of the matrix structure of the E area and the decrease of the shear strength of the Al/Mg interface.展开更多
Mg/Cu bimetal composites were prepared by compound casting method, and the microstructure evolution, phase constitution and bonding strength at the interface were investigated.It is found that a good metallurgical bon...Mg/Cu bimetal composites were prepared by compound casting method, and the microstructure evolution, phase constitution and bonding strength at the interface were investigated.It is found that a good metallurgical bonding can be achieved at the interface of Mg and Cu,which consists of two sub-layers,i.e.,layer I with 30μm on the copper side composed of Mg2Cu matrix phase, on which a small amount of dendritic MgCu2 phase was randomly distributed;layerⅡ with 140μm on the magnesium side made up of the lamellar nano-eutectic network Mg2Cu+(Mg) and a small amount of detached Mg2Cu phase. The average interfacial shear strength of the bimetal composite is measured to be 13 MPa.This study provides a new fabrication process for the application of Mg/Cu bimetal composites as the hydrogen storage materials.展开更多
In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HE...In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.展开更多
In this paper,a Ni coating was deposited on the surface of the A356 aluminum alloy by high velocity oxygen fuel spraying to improve the performance of the AZ91D magnesium/A356 aluminum bimetal prepared by a compound c...In this paper,a Ni coating was deposited on the surface of the A356 aluminum alloy by high velocity oxygen fuel spraying to improve the performance of the AZ91D magnesium/A356 aluminum bimetal prepared by a compound casting.The effects of the Ni coating as well as its thickness on microstructure and mechanical properties of the AZ91D/A356 bimetal were systematically researched for the first time.Results demonstrated that the Ni coating and its thickness had a significant effect on the interfacial phase compositions and mechanical properties of the AZ91D/A356 bimetal.The 10μm’s Ni coating cannot prevent the generation of the Al-Mg intermetallic compounds(IMCs)at the interface zone of the AZ91D/A356 bimetal,while the Ni coating with the thickness of 45μm and 190μm can avoid the formation of the Al-Mg IMCs.When the Ni coating was 45μm,the Ni coating disappeared and transformed into Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles at the interface zone.With a thickness of 190μm’s Ni coating,part of the Ni coating remained and the interface layer was composed of the Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles,Mg_(2)Ni layer,Ni solid solution(SS)layer,Al_(3)Ni_(2) layer,Al_(3)Ni layer and sporadic Al_(3)Ni+Al-Al_(3)Ni eutectic structures from AZ91D side to A356 side in sequence.The interface layer consisting of the Mg-Ni and Al-Ni IMCs obtained with the Ni coating had an obvious lower hardness than the Al-Mg IMCs.The shear strength of the AZ91D/A356 bimetal with a Ni coating of 45μm thickness enhanced 41.4%in comparison with that of the bimetal without Ni coating,and the fracture of the bimetal with 45μm’s Ni coating occurred between the Mg matrix and the interface layer with a mixture of brittle fracture and ductile fracture.展开更多
In this work,the A356/AZ91D bimetal composites were prepared by ultrasonic vibration-assisted lost foam compound casting,and the effects of ultrasonic powers on interfacial microstructures and mechan-ical properties o...In this work,the A356/AZ91D bimetal composites were prepared by ultrasonic vibration-assisted lost foam compound casting,and the effects of ultrasonic powers on interfacial microstructures and mechan-ical properties of the Al/Mg interfaces were investigated.Results revealed that the Al/Mg bimetal com-posites without ultrasonic vibration treatment(UVT)were heterogeneous,and the Al/Mg interface was composed of Al-Mg intermetallic compounds(IMCs,i.e.,Al_(3)Mg_(2)and Al_(12)Mg_(17))area and Al-Mg eutec-tic structures(δ-Mg+Al_(12)Mg_(17))area.The Mg_(2)Si particles were gathered at the IMCs area and an oxide film that mainly composed of Al_(2)O_(3)was existed between the IMCs area and eutectic structures area.With UVT,the oxide film was eliminated and the gathered Mg_(2)Si particles were refined and dispersed by the acoustic cavitation effect,and part of the Al_(3)Mg_(2)and Al-Mg eutectic structures were transformed into the Al_(12)Mg_(17)due to the promoted solute interdiffusion,which improved the homogeneity of the Al/Mg interfaces.Besides,the grains of the Al/Mg interface with UVT under ultrasonic power of 75 W were significantly refined.The thickness of Al/Mg interface was increased with the increase of the ul-trasonic power.Due to the excessive heat induced by UVT under the further increased ultrasonic power,the cooling rates and the degree of supercooling were reduced,resulting in the coarsening of interfacial grains.The microhardness of the Al/Mg interfaces was increased and got more uniform by UVT.The shear strengths of the Al/Mg bimetal composites with UVT were enhanced to 61.4 MPa from 32.4 MPa,with an increase of 89.5%compared with that of the Al/Mg bimetal without UVT.This could be ascribed to the removal of the oxide film,the refinement of the interfacial grains and the dispersed and refined Mg_(2)Si particles achieved by UVT,which hindered the crack propagation during deformation.展开更多
In this work,a new treatment method combining ultrasonic vibration with FeCoNiCrCu high entropy alloy(HEA)coating was used to prepared Al/Mg bimetal through the lost foam compound casting.The effects of composite trea...In this work,a new treatment method combining ultrasonic vibration with FeCoNiCrCu high entropy alloy(HEA)coating was used to prepared Al/Mg bimetal through the lost foam compound casting.The effects of composite treatment involving ultrasonic vibration and HEA coating on interfacial microstructure and mechanical properties of Al/Mg bimetal were studied.Results demonstrate that the interface thickness of the Al/Mg bimetal with composite treatment significantly decreases to only 26.99%of the thickness observed in the untreated Al/Mg bimetal.The HEA coating hinders the diffusion between Al and Mg,resulting the significant reduction in Al/Mg intermetallic compounds in the interface.The Al/Mg bimetal interface with composite treatment is composed of Al_(3)Mg_(2)and Mg_(2)Si/AlxFeCoNiCrCu+FeCoNiCrCu/δ-Mg+Al_(12)Mg_(17)eutectic structures.The interface resulting from the composite treatment has a lower hardness than that without treatment.The acoustic cavitation and acoustic streaming effects generated by ultrasonic vibration promote the diffusion of Al elements within the HEA coating,resulting in a significant improvement in the metallurgical bonding quality on the Mg side.The fracture position shifts from the Mg side of the Al/Mg bimetal only with HEA coating to the Al side with composite treatment.The shear strength of the Al/Mg bimetal increases from 32.16 MPa without treatment to 63.44 MPa with ultrasonic vibration and HEA coating,increasing by 97.26%.展开更多
The influence of the microstructure on mechanical properties of AlSi10Mg fabricated by casting and selective laser melting(SLM)were investigated and contrasted in this work,with an emphasis on understanding the formin...The influence of the microstructure on mechanical properties of AlSi10Mg fabricated by casting and selective laser melting(SLM)were investigated and contrasted in this work,with an emphasis on understanding the forming mechanism.The microstructure,phase structure and mechanical properties were characterized by scanning electron microscopy/field-emission Transmission Electron Microscopy(SEM/TEM),X-Ray Diffraction(XRD),tensile and fatigue tests.The results indicated that the SLM AlSi10Mg exhibited a supersaturated Si network structure precipitated alongα-Al cell.Brittleβ-Al5FeSi andπ-Al8FeMg3Si6 phases were found in the as-cast and SLM AlSi10Mg respectively due to different thermal histories during processing.The SLM AlSi10Mg showed higher tensile strength but lower elongation than the casting,as the result of grain refinement and tortuous crack path.The fatigue results revealed that unmelted powder,oxide inclusion and pores can considerably degrade the fatigue properties for the SLM AlSi10Mg.The SLM process offered a new method for material processing that would avoid harmful Fe-bearing intermetallic compounds and refine the microstructures for enhancing strength.展开更多
Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂ca...Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂casting-rolling compound forming technology＂ is researched by taking the typical 42CrMo slew bearing as object. Through theoretical analysis, the design criteria of the main casting-rolling forming parameters are put forward at first. Then the constitutive relationship model of as-cast 42CrMo steel and its mathematical model of dynamic recrystallization are obtained according to the results of the hot compression experiment. By a coupled thermal-mechanical finite element model for radial-axial rolling of bearing ring, the fraction of dynamic recrystallization is calculated and recrystallized grains size are predicated. Meanwhile, the effects of the initial rolling temperature and feed rate of idle roll on material microstructure evolution are analyzed. Finally, the industrial rolling experiment is designed and performed, based on the simulation results. In addition, mechanical and metallographic tests are conducted on rolled bearing ring to get the mechanical parameters and metallographic structure. The experimental data and results show that the mechanical properties of bearing ring produced by casting-rolling compound forming technology are up to industrial standard, and a qualified bearing ring can be successfully formed by employing this new technology. Through the study, a process of forming large bearing ring directly by using casting ring blank is obtained, which could provide an effective theoretical guidance for manufacturing large ring parts. It also has an edge in saving material, lowering energy and improving efficiency.展开更多
The effective surface treatment method for steel insert composited with Al base metal by expendable pattern casting （EPC） process and the bonding interface between steel insert and Al base metal were investigated.It...The effective surface treatment method for steel insert composited with Al base metal by expendable pattern casting （EPC） process and the bonding interface between steel insert and Al base metal were investigated.It was found that Zn plating on steel insert was effective on improving the bonding property between steel insert and Al base metal in EPC process.Zn is thought to promote the formation of diffusion layer.But almost none content of Zn was observed in the boundary which had been plated on the steel insert.A diffusion layer consisting of Al,Si and Fe was formed at the insert/alloy interface and its hardness was higher than the steel insert as matter of course Al base metal.This layer turned out to be intermetallic compounds of Al-Si-Fe system.Higher pouring temperature promoted the diffusion of Fe into Al alloy,so Fe content in intermetallic layers increased at higher pouring temperature.The layer nearest to steel disappeared due to applied pressure.展开更多
Abstract： The demand for high performance cast aluminum alloy components is often disturbed by increasing impurity elements, such as iron accumulated from recycled scraps. It is strongly required that coarse plate-li...Abstract： The demand for high performance cast aluminum alloy components is often disturbed by increasing impurity elements, such as iron accumulated from recycled scraps. It is strongly required that coarse plate-like iron compound of β-Al5FeSi turns into harmless form without the need for applying refining additives or expensive virgin ingots. The microstructural modification of Al-7mass%Si alloy billets with different iron contents was examined by applying ultrasonic vibration during the solidification. Ultrasonically melt-treated billets were thixocast right after induction heating up to the semisolid temperature of 583 ℃, the microstructure and tensile properties were evaluated in the thixocast components. Globular primary reAl is required to fill up a thin cavity in thixocasting, so that the microstructural modification by ultrasonic melt-treatment was firstly confirmed in the billets. With ultrasonic melt-treatment in the temperature range of 630 ℃ to 605 ℃, the primary α-AI transforms itself from dendrite into fine globular in morphology. The coarse plate-like β-AIsFeSi compound becomes markedly finer compared with those in non-treated billets. Semisolid soaking up to 583 ℃, does not appreciably affect the size of β-AIsFeSi compounds; however, it affects the solid primary reAl morphology to be more globular, which is convenient for thixocasting. After thixocasting with preheated billets, eutectic silicon plates are extremely refined due to the rapid solidification arising from low casting temperature. The tensile strength of thixocast samples with different iron contents does not change much even at 2mass% of iron, when thixocast with ultrasonically melt-treated billets. However, thixocast AI-7mass%Si-2mass%Fe alloy with non-treated billets exhibits an inferior strength of 80 MPa, compared with 180 MPa with ultrasonically melt-treated billets. The elongation is also improved by about a factor of two in thixocastings with ultrasonically melt-treated billets for all iron contents of AI-7mass%Si alloys, for example, the elongation of 11% in thixocast of AI-7mass%Si-0.5mass%Fe alloy with ultrasonically melt-treated billets, 5% in that with non-treated billets.展开更多
基金financially supported by the National Natural Science Foundation of China(Grant No.52275370)the Key R&D Program of Hubei Province,China(Grant No.2024BAB072)the Research Fund of the State Key Laboratory of Intelligent Agricultural Power Equipment(Grant No.SKLIAPE2023014).
文摘A356/6061 bimetallic specimens were prepared by liquid-solid compound casting.The effects of various casting conditions on the interfacial microstructure and mechanical properties of the bimetallic specimens were studied.Results demonstrate that a combination of chemical zinc deposition and electroplating can create a dense protective layer on the surface of the 6061 aluminum bar,achieving complete metallurgical bonding at the bimetallic interface.The interfacial microstructure is primarily characterized by equiaxed grain formation,with eutectic silicon distributed along the grain boundaries.Notably,the thickness of the zinc plating layer does not significantly influence the microstructure of the interface transition layer.Pouring temperature is critical for establishing metallurgical bonding at the bimetallic interface,with the thickness of the transition layer increasing as the pouring temperature rises.The hardness of the bimetallic composite interface falls between the hardness values of the two constituent materials.While the thickness of the galvanized layer has a minimal effect on interfacial shear strength,there is a slight decrease in shear strength with increasing pouring temperature,with a maximum value recorded at 68 MPa.
基金Project(cstc2015yykfC0001)supported by the National Engineering Research Centre for Magnesium Alloys,ChinaProject supported by State Key Laboratory of Mechanical Transmission of Chongqing University,China
文摘The liquid-solid compound casting technology was used to produce the AZ91D/0Cr19Ni9 bimetal composite without and with hot dipping aluminium, respectively. The influences of Al coating on microstructures and mechanical properties of AZ91D/0Cr19Ni9 interface were investigated. The results showed that the mechanical bonding was obtained between AZ91D and bare steel 0Cr19Ni9 where a gap existed at the interface; the metallurgical bonding was formed between AZ91D and Al-coated 0Cr19Ni9, which could be divided into two different intermetallic layers: layer Ⅰ was mainly composed of α-Mg+β-Mg17Al12 eutectic structure and a small amount of MgAl2O4, and layer Ⅱ mainly comprised of Fe2Al5 intermetallic compound. Furthermore, the hardness value of interface was obviously higher than that of AZ91D matrix, and the average hardness values of layers Ⅰ and Ⅱ were HV 158 and HV 493, respectively. The shear strength of AZ91D/Al-coated 0Cr19Ni9 interface was higher than that of AZ91D/bare 0Cr19Ni9 interface, which confirmed that Al coating could improve the adhesive strength between AZ91D and 0Cr19Ni9 during liquid-solid compound casting process.
基金Project(51571080)supported by the National Natural Science Foundation of China
文摘A Ni-P coating was deposited on Cu substrate by electroless plating and the Al/Cu bimetal was produced by solid？liquid compound casting technology. The microstructure, mechanical properties and conductivity of Al/Cu joints with different process parameters （bonding temperature and preheating time） were investigated. The results showed that intermetallics formed at the interface and the thickness and variety increased with the increase of bonding temperature and preheating time. The Ni？P interlayer functioned as a diffusion barrier and protective film which effectively reduced the formation of intermetallics. The shear strength and conductivity of Al/Cu bimetal were reduced by increasing the thickness of intermetallics. In particular, the detrimental effect of Al2Cu phase was more obvious compared with the others. The sample preheated at 780 ℃ for 150 s exhibited the maximum shear strength and conductivity of 49.8 MPa and 5.29×10^5 S/cm, respectively.
基金supported by the Natural Science Foundation of Shanxi Province(202103021224193).
文摘Al/steel bimetallic composites were prepared by compound casting,and the effects of the rotating magnetic field on the interfacial microstructure and shear property of bimetallic composite was investigated.The application of rotating magnetic field refined the grain structure of the Al alloy matrix,changed the eutectic Si morphology from coarse lath to needle-like.The rotating magnetic field improved the temperature field and solute distribution of the Al alloy melt,enriched a layer of Si at the interface,and suppressed the growth of intermetallic compounds,the thickness of the interface layer decreased from 44.9μm to 22.8μm.The interfacial intermetallic compounds consisted ofη-Al_(5)Fe_(2),θ-Al_(13)Fe_(4),τ6-Al_(4.5)FeSi,τ_(5)-Al_(8)Fe_(2)Si andτ_(3)-Al_(2)FeSi,and the addition of the rotating magnetic field did not change phase composition.The rotating magnetic field improved the stress distribution within the interfacial intermetallic compounds,the presence of high-angle grain boundaries retarded crack extension,and the shear strength was enhanced from 31.27±3 MPa to 52.70±4 MPa.This work provides a feasible method for preparing Al/steel bimetallic composite with good bonding property.
文摘The centrifugal casting of compound HSS/nodular cast iron roll collar was studied,and the factors affecting transition zone quality were analyzed.The pouring temperature and interval in pouring are the main factors affecting transition zone quality.By controlling process parameter and flux adding during casting,high quality roll collar was obtained.The cause,why in the casting of HSS part,segregation appears easily,was analyzed and the countermeasure eliminating segregation was put forward,the measure eliminating heat treatment crackling was also put forward.
基金Item Sponsored by National Natural Science Foundation of China(50805109)Fundamental Research Funds for Central Universities of China(2011-1a-023)
文摘Impact,friction and corrosion from the grinding balls and the grinding medium during the mineral processing result in liner breakage.Liner,made from Hadfield steel or alloyed steel,could not have served in wet grinding environment for more than ten months.Composite liner,made from HCWCI(high Cr white cast iron)and carbon steel,has been developed successfully with liquid-liquid composing process based on LFC(lost foam casting).The microstructure of composite was analyzed with optical microscope,SEM(scanning electron microscope)/EDX energy-dispersive X-ray and XRD(X-ray diffraction).According to micrograph,the combination region of two metals was staggered like dogtooth,no mixtures occurred between two liquid metals,and its interface presented excellent metallurgical bonding state.The results of mechanical property test show that,the hardness of HRC,the fracture toughness,and the bending strength are more than 61,16.5 J/cm2 and 1600 MPa,respectively.Comparison between liners made from bimetal composite and alloyed steel has also been investigated in industrial hematite ball mill.The results of eight months test in wet grinding environment prove that the service life of bimetal composite liner is three times as long as that of one made from alloyed steel.
基金the supports provided by the National Natural Science Foundation of China (Grant Nos.52271102,52075198 and 52205359)the China Post-doctoral Science Foundation (Grant No.2021M691112)the Analytical and Testing Center,HUST。
文摘Mg/Al bimetal combines the advantages of both aluminum and magnesium and has broad application prospects in automotive, aerospace,weapons, digital products and so on. The compound casting has the characteristics of low cost, easy to achieve metallurgical combination and suitable for the preparation of complex bimetallic parts. However, bimetallic joint strength is low due to differences of physical properties between Al and Mg, oxide film on metallic surface and interfacial Al-Mg IMCs, which is closely related to the interfacial microstructure and properties. Therefore, how to control the interface of the bimetal to achieve performance enhancement is the focus and difficulty in this field. At present, there are mainly the following strengthening methods. First, the “zincate galvanizing” and “electrolytic polishing+anodic oxidation” technology were exert on the surface of Al alloy to remove and break the oxide film, which improved the wettability between Al and Mg. Second, the undesirable Al-Mg IMCs were reduce or elimination by adding the interlayers(Zn, Ni and Ni-Cu). Thirdly, the evolution process of interfacial microstructure was changed and fine strengthening phases were formed by adding Si element to Al alloy or rare earth element to Mg alloy. Fourthly, mechanical vibration and ultrasonic vibration were applied in the process of the filling and solidification to refine and homogenize the interfacial structure. Finally, some other methods, including secondary rolling, thermal modification, heat treatment and constructing exterior 3D morphology, also can be used to regulate the interfacial microstructure and compositions. The above strengthening methods can be used alone or in combination to achieve bimetallic strengthening. Finally, the future development direction of the Mg/Al bimetal is prospected, which provides some new ideas for the development and application of the Mg/Al bimetal.
基金The authors would like to acknowledge the financial supports from the National Natural Science Foundation of China(No.51875062).
文摘The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects of casting temperatures on microstructural evolution,properties,and fracture behaviors of Ni-coated TC4/AZ91D bimetals by the solid–liquid compound casting(SLCC).The scanning electron microscopy(SEM)and the energy dispersive spectroscopy(EDS)results showed that the interfacial zone mainly composed of nickel,Mg_(2)Ni and Mg-Al-Ni in the bimetals cast at 660℃.As the pouring temperature was increased to 750℃,the width of the interface zone,which mainly composed ofδ(Mg),Mg_(2)Ni,Mg-Al-Ni,Mg_(3)TiNi_(2) and Al_(3)Ni,gradually increased.The microhardness tests showed that the micro-hardness of the interface zone was smaller than that of TC4 substrate but larger than that of the cast AZ91D matrix.At the pouring temperature of 720℃,the Ni-coated TC4/AZ91D bimetals had the most typical homogeneous interface,which had granular Mg-Al-Ni ternary phase but no ribbon-like Al3Ni binary phase,and achieved the highest shear strength of 97.35MPa.Meanwhile,further fracture behavior analysis showed that most fracture failure of Ni-coated TC4/AZ91D bimetals occurred at the Mg_(2)Ni+δ(Mg)eutectic structure and Al_(3)Ni hard intermetallic.
基金the financial support from the National Natural Science Foundation of China(No.51875062)。
文摘To achieve Ti/Mg bimetallic composite with high strength and metallurgical bonding interface,Al interlayer and Zn/Al composite interlayer were used to prepare TC4/AZ91D bimetal composite with metallurgical bonding interface by solid-liquid compound casting,respectively.Al interlayer was prepared on the surface of TC4 alloy by hot dipping,and Zn/Al composite interlayer was prepared by electroplating process.The results suggested that the phases across the interface were Al Ti andα(Al)+Mg_(21)(Al,Zn)_(17)when Zn/Al composite interlayer was used.When Al interlayer was used as interlayer,Al Mg Ti ternary structure and Al_(12)Mg_(17)+δ-Mg eutectic structure were the main phases at the interface.The shear strength of TC4/AZ91D bimetal with Zn/Al composite interlayer was much higher than that with pure Al interlayer,and the value of the shear strength was increased from 48.5 to 67.4 MPa.Thermodynamic models based on different compositions of the interface were established to explain the microstructure evolution of the interfacial zone.
基金the supports provided by the National Natural Science Foundation of China(No.52075198)the National Key Research and Development Program of China(Nos.2020YFB2008300,2020YFB2008304)+1 种基金the State Key Lab of Advanced Metals and Materials(No.2021-ZD07)the Analytical and Testing Center,HUST。
文摘In this work,a vibration was applied in the preparation of the Mg/Al bimetal by a novel compound casting in order to improve the mechanical properties of the Mg/Al bimetal,and the effect of the vibration on the interfacial microstructure and mechanical properties of the Mg/Al bimetal was investigated.The results indicated that the vibration had a significant effect on the interfacial microstructure and mechanical properties of the Mg/Al bimetal,but it did not change the phase compositions of the interface,which was composed of layerⅠ(Al3Mg2+Mg2Si),layerⅡ(Al_(12)Mg_(17)+Mg_(2)Si)and layerⅢ(Al_(12)Mg_(17)/δ-Mg).Without vibration,the Mg_(2)Si phase with a needle-like morphology mainly aggregated in the layerⅡof the interface.After the application of the vibration,the SEM and EBSD analysis results showed that the Mg_(2)Si and Al3Mg2phases in the interface were obviously refined,and the distribution of the Mg_(2)Si became more uniform,due to the strong forced convection of the molten metal resulting from the vibration.The TEM analysis indicated that the interface between the A_(l3)Mg_(2) and Mg_(2)Si phases was non-coherent,suggesting the Mg_(2)Si particles cannot act as a heterogeneous nucleation base during the solidification process of the interface.Compared to the Mg/Al bimetal without vibration,the shear strength of the Mg/Al bimetal with vibration increased by about 50%from 31.7 MPa on average to 47.5 MPa,and the hardness of the layer I of the interface increased,and the hardness of the layerⅢdecreased.The fracture surface transformed from a flat fracture morphology without vibration to an irregular zigzag fracture morphology.
基金the supports provided by the National Natural Science Foundation of China(No.52075198)the National Key Research and Development Program of China(No.2020YFB2008304)+1 种基金the State Key Lab of Advanced Metals and Materials(No.2021-ZD07)the Analytical and Testing Center,HUST。
文摘To improve the Al/Mg bimetallic interface,La was added into the Al/Mg bimetallic interface manufactured by a compound casting process.The effect of La addition on the microstructure,mechanical properties and fracture behavior of the Al/Mg bimetallic interface and the formation mechanism of the interface were studied in detail.Al_(11)La_(3),Al_(8)Mn_(4)La,Al_(20)Ti_(2)La,and other rare earth precipitates(RE precipitates)preferentially precipitated at the interface with La addition,while the number of the Al_(11)La_(3)and Al_(8)Mn_(4)La located in eutectic structure area(E area)gradually increased and aggregated in the interface with the increase of the La content.Besides,the matrix structure in different areas of the Al/Mg interface changed in different degrees,and the eutectic structure and primaryγ(Mg_(17)Al_(12))dendrites in the E area were refned,but the intermetallic compounds area(IMC area)had no obvious change.With the addition of the La,the interface was strengthened under the comprehensive effect of refnement strengthening and precipitation strengthening from the E area.When the La content increased to 1.0%,the shear strength of the Al/Mg bimetal reached the maximum of 51.54 MPa,which was 30.95%higher than the group without La addition.However,with the further increase of the La content,the large area aggregation of the Al_(11)La_(3)and Al_(8)Mn_(4)La occurred in the interface,leading to the separation of the matrix structure of the E area and the decrease of the shear strength of the Al/Mg interface.
基金Project(51671017)supported by the National Natural Science Foundation of ChinaProject(FRF-GF-17-B3)supported by the Fundamental Research Funds for the Central Universities,China+1 种基金Project supported by the Beijing Laboratory of Metallic Materials and Processing for Modern Transportation,ChinaProject(SKLSP201835)supported by the Fund of the State Key Laboratory of Solidification Processing in NWPU,China
文摘Mg/Cu bimetal composites were prepared by compound casting method, and the microstructure evolution, phase constitution and bonding strength at the interface were investigated.It is found that a good metallurgical bonding can be achieved at the interface of Mg and Cu,which consists of two sub-layers,i.e.,layer I with 30μm on the copper side composed of Mg2Cu matrix phase, on which a small amount of dendritic MgCu2 phase was randomly distributed;layerⅡ with 140μm on the magnesium side made up of the lamellar nano-eutectic network Mg2Cu+(Mg) and a small amount of detached Mg2Cu phase. The average interfacial shear strength of the bimetal composite is measured to be 13 MPa.This study provides a new fabrication process for the application of Mg/Cu bimetal composites as the hydrogen storage materials.
基金financial supports from the National Natural Science Foundation of China (No. 51875062)China Postdoctoral Science Foundation (No. 2021M700567)。
文摘In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.
基金supports provided by the National Natural Science Foundation of China (No. 52075198)the National Key Research and Development Program of China (Nos. 2020YFB2008300 and 2020YFB2008304)+1 种基金the State Key Laboratory of High Performance Complex Manufacturing in CSU (No. Kfkt2019-01)the Analytical and Testing Center, HUST.
文摘In this paper,a Ni coating was deposited on the surface of the A356 aluminum alloy by high velocity oxygen fuel spraying to improve the performance of the AZ91D magnesium/A356 aluminum bimetal prepared by a compound casting.The effects of the Ni coating as well as its thickness on microstructure and mechanical properties of the AZ91D/A356 bimetal were systematically researched for the first time.Results demonstrated that the Ni coating and its thickness had a significant effect on the interfacial phase compositions and mechanical properties of the AZ91D/A356 bimetal.The 10μm’s Ni coating cannot prevent the generation of the Al-Mg intermetallic compounds(IMCs)at the interface zone of the AZ91D/A356 bimetal,while the Ni coating with the thickness of 45μm and 190μm can avoid the formation of the Al-Mg IMCs.When the Ni coating was 45μm,the Ni coating disappeared and transformed into Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles at the interface zone.With a thickness of 190μm’s Ni coating,part of the Ni coating remained and the interface layer was composed of the Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles,Mg_(2)Ni layer,Ni solid solution(SS)layer,Al_(3)Ni_(2) layer,Al_(3)Ni layer and sporadic Al_(3)Ni+Al-Al_(3)Ni eutectic structures from AZ91D side to A356 side in sequence.The interface layer consisting of the Mg-Ni and Al-Ni IMCs obtained with the Ni coating had an obvious lower hardness than the Al-Mg IMCs.The shear strength of the AZ91D/A356 bimetal with a Ni coating of 45μm thickness enhanced 41.4%in comparison with that of the bimetal without Ni coating,and the fracture of the bimetal with 45μm’s Ni coating occurred between the Mg matrix and the interface layer with a mixture of brittle fracture and ductile fracture.
基金supported by the National Natural Science Foundation of China(Nos.52271102 and 52075198)the National Key Research and Development Program of China(No.2020YFB2008304),and the Analytical and Testing Center,HUST。
文摘In this work,the A356/AZ91D bimetal composites were prepared by ultrasonic vibration-assisted lost foam compound casting,and the effects of ultrasonic powers on interfacial microstructures and mechan-ical properties of the Al/Mg interfaces were investigated.Results revealed that the Al/Mg bimetal com-posites without ultrasonic vibration treatment(UVT)were heterogeneous,and the Al/Mg interface was composed of Al-Mg intermetallic compounds(IMCs,i.e.,Al_(3)Mg_(2)and Al_(12)Mg_(17))area and Al-Mg eutec-tic structures(δ-Mg+Al_(12)Mg_(17))area.The Mg_(2)Si particles were gathered at the IMCs area and an oxide film that mainly composed of Al_(2)O_(3)was existed between the IMCs area and eutectic structures area.With UVT,the oxide film was eliminated and the gathered Mg_(2)Si particles were refined and dispersed by the acoustic cavitation effect,and part of the Al_(3)Mg_(2)and Al-Mg eutectic structures were transformed into the Al_(12)Mg_(17)due to the promoted solute interdiffusion,which improved the homogeneity of the Al/Mg interfaces.Besides,the grains of the Al/Mg interface with UVT under ultrasonic power of 75 W were significantly refined.The thickness of Al/Mg interface was increased with the increase of the ul-trasonic power.Due to the excessive heat induced by UVT under the further increased ultrasonic power,the cooling rates and the degree of supercooling were reduced,resulting in the coarsening of interfacial grains.The microhardness of the Al/Mg interfaces was increased and got more uniform by UVT.The shear strengths of the Al/Mg bimetal composites with UVT were enhanced to 61.4 MPa from 32.4 MPa,with an increase of 89.5%compared with that of the Al/Mg bimetal without UVT.This could be ascribed to the removal of the oxide film,the refinement of the interfacial grains and the dispersed and refined Mg_(2)Si particles achieved by UVT,which hindered the crack propagation during deformation.
基金funded by the National Natural Science Foundation of China(Nos.52271102,52075198 and 52205359)。
文摘In this work,a new treatment method combining ultrasonic vibration with FeCoNiCrCu high entropy alloy(HEA)coating was used to prepared Al/Mg bimetal through the lost foam compound casting.The effects of composite treatment involving ultrasonic vibration and HEA coating on interfacial microstructure and mechanical properties of Al/Mg bimetal were studied.Results demonstrate that the interface thickness of the Al/Mg bimetal with composite treatment significantly decreases to only 26.99%of the thickness observed in the untreated Al/Mg bimetal.The HEA coating hinders the diffusion between Al and Mg,resulting the significant reduction in Al/Mg intermetallic compounds in the interface.The Al/Mg bimetal interface with composite treatment is composed of Al_(3)Mg_(2)and Mg_(2)Si/AlxFeCoNiCrCu+FeCoNiCrCu/δ-Mg+Al_(12)Mg_(17)eutectic structures.The interface resulting from the composite treatment has a lower hardness than that without treatment.The acoustic cavitation and acoustic streaming effects generated by ultrasonic vibration promote the diffusion of Al elements within the HEA coating,resulting in a significant improvement in the metallurgical bonding quality on the Mg side.The fracture position shifts from the Mg side of the Al/Mg bimetal only with HEA coating to the Al side with composite treatment.The shear strength of the Al/Mg bimetal increases from 32.16 MPa without treatment to 63.44 MPa with ultrasonic vibration and HEA coating,increasing by 97.26%.
基金financially supported by the Boeing Company/HuaZhong University of Science and Technology Project“Compressor wheel production by laser additive manufacturing using Ti and Al alloy powders”(No.2016-495)the Hubei Science Fund for Distinguished Young Scholars(No.0216110085)+1 种基金the Wuhan Morning Light Plan of Youth Science and Technology(No.0216110066)the Academic Frontier Youth Team(Nos.2017QYTD06 and 2018QYTD04)at Huazhong University of Science and Technology(HUST).
文摘The influence of the microstructure on mechanical properties of AlSi10Mg fabricated by casting and selective laser melting(SLM)were investigated and contrasted in this work,with an emphasis on understanding the forming mechanism.The microstructure,phase structure and mechanical properties were characterized by scanning electron microscopy/field-emission Transmission Electron Microscopy(SEM/TEM),X-Ray Diffraction(XRD),tensile and fatigue tests.The results indicated that the SLM AlSi10Mg exhibited a supersaturated Si network structure precipitated alongα-Al cell.Brittleβ-Al5FeSi andπ-Al8FeMg3Si6 phases were found in the as-cast and SLM AlSi10Mg respectively due to different thermal histories during processing.The SLM AlSi10Mg showed higher tensile strength but lower elongation than the casting,as the result of grain refinement and tortuous crack path.The fatigue results revealed that unmelted powder,oxide inclusion and pores can considerably degrade the fatigue properties for the SLM AlSi10Mg.The SLM process offered a new method for material processing that would avoid harmful Fe-bearing intermetallic compounds and refine the microstructures for enhancing strength.
基金supported by Key Program of National Natural Science Foundation of China(Grant No.51135007)National Natural Science Foundation of China(Grant No.51075290)
文摘Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂casting-rolling compound forming technology＂ is researched by taking the typical 42CrMo slew bearing as object. Through theoretical analysis, the design criteria of the main casting-rolling forming parameters are put forward at first. Then the constitutive relationship model of as-cast 42CrMo steel and its mathematical model of dynamic recrystallization are obtained according to the results of the hot compression experiment. By a coupled thermal-mechanical finite element model for radial-axial rolling of bearing ring, the fraction of dynamic recrystallization is calculated and recrystallized grains size are predicated. Meanwhile, the effects of the initial rolling temperature and feed rate of idle roll on material microstructure evolution are analyzed. Finally, the industrial rolling experiment is designed and performed, based on the simulation results. In addition, mechanical and metallographic tests are conducted on rolled bearing ring to get the mechanical parameters and metallographic structure. The experimental data and results show that the mechanical properties of bearing ring produced by casting-rolling compound forming technology are up to industrial standard, and a qualified bearing ring can be successfully formed by employing this new technology. Through the study, a process of forming large bearing ring directly by using casting ring blank is obtained, which could provide an effective theoretical guidance for manufacturing large ring parts. It also has an edge in saving material, lowering energy and improving efficiency.
文摘The effective surface treatment method for steel insert composited with Al base metal by expendable pattern casting （EPC） process and the bonding interface between steel insert and Al base metal were investigated.It was found that Zn plating on steel insert was effective on improving the bonding property between steel insert and Al base metal in EPC process.Zn is thought to promote the formation of diffusion layer.But almost none content of Zn was observed in the boundary which had been plated on the steel insert.A diffusion layer consisting of Al,Si and Fe was formed at the insert/alloy interface and its hardness was higher than the steel insert as matter of course Al base metal.This layer turned out to be intermetallic compounds of Al-Si-Fe system.Higher pouring temperature promoted the diffusion of Fe into Al alloy,so Fe content in intermetallic layers increased at higher pouring temperature.The layer nearest to steel disappeared due to applied pressure.
基金financially supported by the Grants-in Aid for Scientific Research from the Ministry of Education,Science,Sports and Culture (No.23560898)
文摘Abstract： The demand for high performance cast aluminum alloy components is often disturbed by increasing impurity elements, such as iron accumulated from recycled scraps. It is strongly required that coarse plate-like iron compound of β-Al5FeSi turns into harmless form without the need for applying refining additives or expensive virgin ingots. The microstructural modification of Al-7mass%Si alloy billets with different iron contents was examined by applying ultrasonic vibration during the solidification. Ultrasonically melt-treated billets were thixocast right after induction heating up to the semisolid temperature of 583 ℃, the microstructure and tensile properties were evaluated in the thixocast components. Globular primary reAl is required to fill up a thin cavity in thixocasting, so that the microstructural modification by ultrasonic melt-treatment was firstly confirmed in the billets. With ultrasonic melt-treatment in the temperature range of 630 ℃ to 605 ℃, the primary α-AI transforms itself from dendrite into fine globular in morphology. The coarse plate-like β-AIsFeSi compound becomes markedly finer compared with those in non-treated billets. Semisolid soaking up to 583 ℃, does not appreciably affect the size of β-AIsFeSi compounds; however, it affects the solid primary reAl morphology to be more globular, which is convenient for thixocasting. After thixocasting with preheated billets, eutectic silicon plates are extremely refined due to the rapid solidification arising from low casting temperature. The tensile strength of thixocast samples with different iron contents does not change much even at 2mass% of iron, when thixocast with ultrasonically melt-treated billets. However, thixocast AI-7mass%Si-2mass%Fe alloy with non-treated billets exhibits an inferior strength of 80 MPa, compared with 180 MPa with ultrasonically melt-treated billets. The elongation is also improved by about a factor of two in thixocastings with ultrasonically melt-treated billets for all iron contents of AI-7mass%Si alloys, for example, the elongation of 11% in thixocast of AI-7mass%Si-0.5mass%Fe alloy with ultrasonically melt-treated billets, 5% in that with non-treated billets.
