To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretre...To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretreatment was employed to construct a Ta_(2)O_(5)ceramic layer on the Ta12W alloy surface.Subsequently,a slurry spraying-vacuum sintering method was used to prepare a Si-Cr-Ti-Zr coating on the pretreated substrate.Comparative studies were conducted on the microstructure,phase composition,and isothermal oxidation resistance(at 1600℃)of the as-prepared coatings with and without the micro-arc oxidation ceramic layer.The results show that the Ta_(2)O_(5)layer prepared at 400 V is more continuous and has smaller pores than that prepared at 350 V.After microarc oxidation pretreatment,the Si-Cr-Ti-Zr coating on Ta12W alloy consists of three distinct layers:an upper layer dominated by Ti_(5)Si_(3),Ta_(5)Si_(3),and ZrSi;a middle layer dominated by TaSi_(2);a coating/substrate interfacial reaction layer dominated by Ta_(5)Si_(3).Both the Si-Cr-Ti-Zr coatings with and without the Ta_(2)O_(5)ceramic layer do not fail after isothermal oxidation at 1600℃for 5 h.Notably,the addition of the Ta2O5 ceramic layer reduces the high-temperature oxidation rate of the coating.展开更多
Fine-grained nuclear graphite is a key material in high-temperature gas-cooled reactors(HTGRs).During air ingress accidents,core graphite components undergo severe oxidation,threatening structural integrity.Therefore,...Fine-grained nuclear graphite is a key material in high-temperature gas-cooled reactors(HTGRs).During air ingress accidents,core graphite components undergo severe oxidation,threatening structural integrity.Therefore,understanding the oxidation behavior of nuclear graphite is essential for reactor safety.The influence of oxidation involves multiple factors,including temperature,sample size,oxidant,impurities,filler type and size,etc.The size of the filler particles plays a crucial role in this study.Five ultrafine-and superfine-grained nuclear graphite samples(5.9-34.4μm)are manufactured using identical raw materials and manufacturing processes.Isothermal oxidation tests conducted at 650℃-750℃ are used to study the oxidation behavior.Additionally,comprehensive characterization is performed to analyze the crystal structure,surface morphology,and nanoscale to microscale pore structure of the samples.Results indicate that oxidation behavior cannot be predicted solely based on filler grain size.Reactive site concentration,characterized by active surface area,dominates the chemical reaction kinetics,whereas pore tortuosity,quantified by the structural parameterΨ,plays a key role in regulating oxidant diffusion.These findings clarify the dual role of microstructure in oxidation mechanisms and establish a theoretical and experimental basis for the design of high-performance nuclear graphite capable of long-term service in high-temperature gas-cooled reactors.展开更多
In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti...In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti-mization,for the degradation of landfill leachate(LL)containing elevated levels of tetracycline(TC),and explored its mechanism of action.Firstly,titanium-based ruthenium-iridium(Ti/RuO_(2)-IrO_(2)),titanium-based ruthenium-iridium-platinum(Ti/Pt-RuO_(2)-IrO_(2)),and titanium-based tin-antimony(Ti/SnO_(2)-Sb_(2)O_(3))were employed as an-odes in the electrocatalytic oxidation system,with titanium and stainless steel plates serving as cathodes,to construct the optimal two-dimensional electrocatalytic oxidation system(2D-ECO)through cross-comparison ex-periments.Subsequently,using granular activated carbon(GAC),coconut shell biochar(CBC),walnut shell carbon(WBC),and bamboo charcoal(BBC)as particle electrodes,a 3D-ECO system was developed.The influence of var-ious operational parameters on treating TC-containing LL was investigated.The optimal operating parameters obtained from the study was:pH=5,current density of 30 mA/cm^(2),particle dosage of 7 g/L,particle size ranging from 1.70 to 2.00 mm,and electrode spacing of 4 cm.Under these conditions,the COD removal rate of 3D-ECO within three hours was 90.25%,the TC removal rate was 72.41%,and the NH_(3)-N removal rate was 39.52%.The removal of TC followed a pseudo-first-order kinetic model.Additionally,degradation mechanisms were elucidated through electron paramagnetic resonance(EPR)spectrometer and Tert-Butanol(TBA)quenching experiments,indicating that the degradation primarily occurred through a non-radical(1O_(2))pathway.This re-search offers a comprehensive analysis of the simultaneous breakdown of intricate LL matrices and TC,enhancing our comprehension of the degradation processes and underlying mechanisms.展开更多
Liquid phase oxidation of toluene is an environmental benign route for the production of benzoic acid.In a φ48mm bubble column reactor,the commercial process of toluene liquid phase oxidation was conducted with Co(CH...Liquid phase oxidation of toluene is an environmental benign route for the production of benzoic acid.In a φ48mm bubble column reactor,the commercial process of toluene liquid phase oxidation was conducted with Co(CH3COO)2.4H2O as catalyst.The Co2+ concentration [Co2+] was determined by extraction spectrophotometry and hereby the Co3+ concentration [Co3+] was obtained by mass balance.The results showed that [Co3+] reached the maximum at about 25-30min.[Co3+] increased with increasing Co catalyst amount at total Co concentration<150 mg.L-1 of toluene.The conversion of toluene,yield and selectivity of benzoic acid increased with the increasing [Co3+/Co2+] max.A high [Co3+] and a high [Co3+]/[Co2+] ratio are beneficial to the reaction.展开更多
The latest progress and developments in catalysts for the oxidation of cyclohexane are reviewed. Catalytic systems for the oxidation of cyclohexane including metal supported, metal oxides, molecular sieves, metal subs...The latest progress and developments in catalysts for the oxidation of cyclohexane are reviewed. Catalytic systems for the oxidation of cyclohexane including metal supported, metal oxides, molecular sieves, metal substituted polyoxometalates, photocatalysts, orga nocatalysts, Gif systems, metal-organic catalysts and metalloporphyrins are discussed with a particular emphasis on metalloporphyrin catalytic systems. The advantages and disadvantages of these methods are summarized and analyzed. Finally, the development trends in the oxidation technology of cyclohexane are examined.展开更多
TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing Ti...TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing TiB_(2)coatings have disadvantages such as high equipment costs,complicated processes,and highly toxic gas emissions.This paper proposes an environmentally friendly method,which requires inexpensive equipment and simple processing,for preparing TiB_(2)coating on molybdenum via electrophoretic deposition within Na3AlF6-based molten salts.The produced TiB_(2)layer had an approximate thickness of 60μm and exhibited high density,outstanding hardness(38.2 GPa)and robust adhesion strength(51 N).Additionally,high-temperature oxidation experiments revealed that,at900℃,the TiB_(2)coating provided effective protection to the molybdenum substrate against oxidation for 3 h.This result indicates that the TiB_(2)coating prepared on molybdenum using molten salt electrophoretic deposition possesses good high-temperature oxidation resistance.展开更多
Investigating structural and hydroxyl group effects in electrooxidation of alcohols to value-added products by solid-acid electrocatalysts is essential for upgrading biomass alcohols.Herein,we report efficient electro...Investigating structural and hydroxyl group effects in electrooxidation of alcohols to value-added products by solid-acid electrocatalysts is essential for upgrading biomass alcohols.Herein,we report efficient electrocatalytic oxidations of saturated alcohols(C_(1)-C_(6))to selectively form formate using Ni Co hydroxide(Ni Co-OH)derived Ni Co_(2)O_(4)solid-acid electrocatalysts with balanced Lewis acid(LASs)and Brønsted acid sites(BASs).Thermal treatment transforms BASs-rich(89.6%)Ni Co-OH into Ni Co_(2)O_(4)with nearly equal distribution of LASs(53.1%)and BASs(46.9%)which synergistically promote adsorption and activation of OH-and alcohol molecules for enhanced oxidation activity.In contrast,BASs-enriched Ni Co-OH facilitates formation of higher valence metal sites,beneficial for water oxidation.The combined experimental studies and theoretical calculation imply the oxidation ability of C1-C6alcohols increases as increased number of hydroxyl groups and decreased HOMO-LUMO gaps:methanol(C_(1))<ethylene glycol(C_(2))<glycerol(C3)<meso-erythritol(C4)<xylitol(C5)<sorbitol(C6),while the formate selectivity shows the opposite trend from 100 to 80%.This study unveils synergistic roles of LASs and BASs,as well as hydroxyl group effect in electro-upgrading of alcohols using solid-acid electrocatalysts.展开更多
Pt/CeO2–ZrO2–SnO2/γ-Al2O3 catalysts were prepared by co-precipitation and wet impregnation methods for catalytic oxidation of acetaldehyde to acetic acid in water. In the present catalysts, Pt and CeO2–ZrO2–SnO2 ...Pt/CeO2–ZrO2–SnO2/γ-Al2O3 catalysts were prepared by co-precipitation and wet impregnation methods for catalytic oxidation of acetaldehyde to acetic acid in water. In the present catalysts, Pt and CeO2–ZrO2–SnO2 were successfully dispersed on the γ-Al2O3 support.Dependences of platinum content and reaction time on the selective oxidation of acetaldehyde to acetic acid were investigated to optimize the reaction conditions for obtaining both high acetaldehyde conversion and highest selectivity to acetic acid. Among the catalysts, a Pt（6.4 wt.%）/Ce0.68Zr0.17Sn0.15O2.0（16 wt.%）/γ-Al2O3 catalyst showed the highest acetaldehyde oxidation activity. On this catalyst, acetaldehyde was completely oxidized after the reaction at 0°C for 8 hr, and the selectivity to acetic acid reached to 95%and higher after the reaction for 4 hr and longer.展开更多
Liquid-phase oxidation of toluene with air has become the main technology for producing benzoic acid in a reactor at present. Based on the kinetic model of the toluene oxidation process obtained from laboratory and ma...Liquid-phase oxidation of toluene with air has become the main technology for producing benzoic acid in a reactor at present. Based on the kinetic model of the toluene oxidation process obtained from laboratory and mass balance of key component, a novel model is established to simulate the industrial toluene oxidation process, in which the effects of benzaldehyde and benzyl alcohol are considered and the kinetic parameters are revised by industrial data. The simulation results show that the error of benzoic acid yield is within 3.5%. Based on the simulation model, to maximize the benzoic acid yield, an optimization model is proposed to optimize the operating parameters, including toluene feed-in mass flux and temperature. The optimization result indicates that on the allowable operating conditions the maximum benzoic acid yield obtained with the reaction temperature at 167.2 C an the mass flux at 104.1 t·h^- 1 is greater than the current one, which can be used to guide industrial reactor s operation.展开更多
In this study, liquid-phase aerobic oxidation of toluene catalyzed by Mn–Mo oxide was conducted in a 1.0 L batch reactor. The macroscopic kinetics of toluene consumption and benzaldehyde generation at 413–443 K were...In this study, liquid-phase aerobic oxidation of toluene catalyzed by Mn–Mo oxide was conducted in a 1.0 L batch reactor. The macroscopic kinetics of toluene consumption and benzaldehyde generation at 413–443 K were obtained from a combination of experimental observation and hypothetical models. The results clearly showed that both the oxidation rate of toluene and generation rate of the aromatic product were proportional to the concentration of the substrate, the partial pressure of oxygen and the surface area of the catalyst. The energy barrier of toluene oxidation to benzyl alcohol was the highest(≈ 81 kJ mol^(-1)), while that of benzyl alcohol oxidation to benzaldehyde was the lowest(≈ 57 kJ mol^(-1)). Moreover, the activation energy of further oxidation of benzaldehyde in an acetic acid solvent was only slightly lower(≈ 1.9 kJ mol^(-1)) than that of toluene oxidation. Significantly, the transformation of benzyl alcohol indeed contributed to the generation of benzaldehyde and this step conformed to a first-order parallel-consecutive model. Increased reaction temperature and residence time favored the transformation of benzyl alcohol to benzaldehyde. In addition, doping with molybdenum at Mn/Mo = 3/1 enhanced the catalytic performance of the heterogeneous catalyst and was attributed to the presence of a synergetic effect between different metal cations. Regarding the microscopic kinetics, the LH-OS-ND mechanism(Langmuir–Hinshelwood adsorption of reagents on the same type of active sites and non-dissociative adsorption of oxygen) was verified as responsible for the heterogeneous oxidation of toluene. Oxygen and benzaldehyde were weakly adsorbed(Δ H_(ads,Oxy) ≈^(-1)5 kJ mol^(-1), Δ H _(ads)0,Bald) ≈-30 kJ mol^(-1)), but showed strong mobility(Δ S_(ads,Oxy) ≈-22 J mol^(-1) K^(-1)), Δ S_(ads,Bald) ≈-39 J mol^(-1) K^(-1)). The fundamental intrinsic rates were deduced based on the LH-OS-ND mechanism and showed great consistency with the macroscopic results.展开更多
During the liquid-phase oxidation of p-xylene,over-oxidation of reactant,intermediates and solvent to carbon dioxide and carbon monoxide is generally known as the burning side reaction.Batch and semi-continuous experi...During the liquid-phase oxidation of p-xylene,over-oxidation of reactant,intermediates and solvent to carbon dioxide and carbon monoxide is generally known as the burning side reaction.Batch and semi-continuous experiments were carried out,and the experimental data of the burning side reaction were analyzed and reported in this paper.The results showed that the rates of burning side reactions were proportional to the rates of the main reaction,but decreased with the increasing concentrations of reactant and intermediates.The inter-stimulative and competitive relationship between the burning side reaction and the main reaction was confirmed,and the rates of the burning side reaction could be described with some key indexes of the main reaction.According to the mechanism of the side reactions and the kinetics model of main reaction which were proposed and tested in the previous papers,a kinetic model of the burning side reactions involving some key indexes of the main reaction was developed,and the parameters were determined by data fitting of the COx rate curves.The obtained kinetic model could describe the burning side reactions adequately.展开更多
The effect of liquid-phase oxidation impurities on the solubility of water in hydrocarbon fuels was studied.The results show that the concentration of polar surfactant molecules in the first region increases(true solu...The effect of liquid-phase oxidation impurities on the solubility of water in hydrocarbon fuels was studied.The results show that the concentration of polar surfactant molecules in the first region increases(true solution)during fuel oxidation,and since the oxidation groups(-COOH,-O=O,-OH,etc.)have similar dipole momentμ,the dielectric loss tangent tanδincreases linearly in this region with surfactant concentration.Upon further oxidation,micelle structures begin to form at a certain point.Micelle formation leads to a sharp decrease in the dipole moment attributable to the monomer unitμ/n,where nis the number of molecules in a micelle.A several-fold decrease in the dipole moment leads to a sharp drop in tanδ.Upon further increase in the number and size of micelles,the dipole moment remains practically unchanged,and the dielectric loss tangent begins to increase linearly again with surfactant concentration.If the critical concentration for micelle formation is achieved upon further oxidation of hydrocarbon liquids,micelle formation processes occur spontaneously in the solution,and the true solution becomes a colloidal system(sol).The resulting micelles are structured with hydrocarbon radicals of molecules toward the outside and hydrophilic(polar)groups toward the inside.Water molecules are located inside micelles and held so securely that water molecules do not aggregate as temperature decreases.The reason for significant differences in the equilibrium solubility of water in hydrocarbon fuels is the different oxidation factors of product samples,resulting from the accumulation of various concentrations of oxidation products,which are natural surfactants,in hydrocarbon fuels.展开更多
The selective oxidation of methanol to methyl formate is one of the most attractive processes to obtain value-added methanol-downstream products.The development of highly efficient and stable catalysts is critical for...The selective oxidation of methanol to methyl formate is one of the most attractive processes to obtain value-added methanol-downstream products.The development of highly efficient and stable catalysts is critical for this transformation.In this study,a series of MIL-88B(Fe_(x),Co_(1‒x))bimetallic catalysts with different Fe/Co molar ratios were prepared through a one-pot hydrothermal method.X-ray diffraction,scanning electron microscopy,high-resolution transmission electron microscopy,energy dispersive spectroscopy,Fourier transform infrared spectroscopy,X-ray photoelectron spectroscopy,N2 adsorption-desorption,and inductively coupled plasma-mass spectrometry characterization were performed to elucidate the structure of the catalysts.The activity of the catalysts were assessed in the one-step oxidation of methanol to methyl formate with H_(2)O_(2)in a liquid-phase batch reactor.The results show that the MIL-88B(Fe_(x),Co_(1‒x))catalysts exhibit uniform needle-like morphologies with an average length and width of 400-600 nm and 100-150 nm,respectively.Co^(2+)is incorporated into the framework by partially replacing Fe^(3+)in MIL-88B.Moreover,the catalyst efficiently promoted the conversion of methanol to methyl formate.When MIL-88B(Fe_(0.7),Co_(0.3))catalyst was used with a molar ratio of H_(2)O_(2)to methanol of 0.5 at 80℃for 60 min,34.8%methanol conversion was achieved,and the selectivity toward methyl formate was 67.6%.The catalysts also showed great stability with a steady conversion and selectivity even after four cycles.The preliminary oxidation mechanism was also studied.It was determined that H_(2)O_(2)is first adsorbed on the Fe^(3+)sites and subsequently activates these sites.Methanol is adsorbed by the O atoms of the framework through hydrogen bonding and is gradually oxidized to formic acid.Subsequently,formic acid reacts with the residual methanol at the Fe^(3+)and Co^(2+)Lewis acid sites to form methyl formate.展开更多
Hydrogen sulfide in rural biogas was removed with liquid-phase catalytic oxidation.By using rare earth as catalyst,and sulfosalicylic acid as stabilizer,H2S purification efficiency could increase as high as 96%,and su...Hydrogen sulfide in rural biogas was removed with liquid-phase catalytic oxidation.By using rare earth as catalyst,and sulfosalicylic acid as stabilizer,H2S purification efficiency could increase as high as 96%,and sulfur capacity of the composite solution was about 3 g/L.The results show that purification efficiency was affected by catalyst addition,pH,experimental temperature,and sulfur capacity.The parameters effects on catalytic oxidation were studied,and the optimized conditions were that Fe3+ concentration 0.08 mg/L,reaction temperature 70°C,pH 9.0,with a absorption solution volume of 50 mL,a gas flow rate 200 mL/min,and H2S mass concentration of 1.58-2.02 mg/m3.展开更多
Up-and-coming high-temperature materials,refractory high entropy alloys,are suffering from lower oxidation resistance,restricting their applications in the aerospace field.In this study,two novel treatments of Al-depo...Up-and-coming high-temperature materials,refractory high entropy alloys,are suffering from lower oxidation resistance,restricting their applications in the aerospace field.In this study,two novel treatments of Al-deposited and remelted were developed to refine the microstructure and enhance the oxidation resistance of refractory high entropy alloy using electron beam freeform fabrication(EBF3).Finer and short-range ordering structures were observed in the remelted sample,whereas the Al-deposited sample showcased the formation of silicide and intermetallic phases.High-temperature cyclic and isothermal oxidation tests at 1000℃ were carried out.The total weight gain after 60 h of cyclic oxidation decreased by 17.49%and 30.46%for the remelted and deposited samples,respectively,compared to the as-cast state.Oxidation kinetics reveal an evident lower mass gain and oxidation rate in the treated samples.A multilayer oxide consisting of TiO_(2)+Al_(2)O_(3)+SiO_(2)+AlNbO_(4) was studied for its excellent oxidation resistance.The oxidation behavior of rutile,corundum and other oxides was analyzed using first principles calculations and chemical defect analysis.Overall,this research,which introduces novel treatments,offers promising insights for enhancing the inherent oxidation resistance of refractory high entropy alloys.展开更多
Pitch produced by the lique-faction of coal was divided into two frac-tions:soluble in toluene(TS)and insol-uble in toluene but soluble in pyridine(TI-PS),and their differences in molecu-lar structure and oxidation ac...Pitch produced by the lique-faction of coal was divided into two frac-tions:soluble in toluene(TS)and insol-uble in toluene but soluble in pyridine(TI-PS),and their differences in molecu-lar structure and oxidation activity were studied.Several different carbon materi-als were produced from them by oxida-tion in air(350℃,300 mL/min)fol-lowed by carbonization(1000℃ in Ar),and the effect of the cross-linked structure on their structure and sodium storage properties was investigated.The results showed that the two pitch fractions were obviously different after the air oxidation.The TS fraction with a low degree of condensation and abundant side chains had a stronger oxidation activity and thus introduced more cross-linked oxygen-containing functional groups C(O)―O which prevented carbon layer rearrangement during the carbonization.As a result,a disordered hard carbon with more defects was formed,which improved the electrochemical performance.Therefore,the carbon materials derived from TS(O-TS-1000)had an obvious disordered structure and a larger layer spacing,giving them better sodium storage perform-ance than those derived from the TI-PS fraction(O-TI-PS-1000).The specific capacity of O-TS-1000 was about 250 mAh/g at 20 mA/g,which was 1.67 times higher than that of O-TI-PS-1000(150 mAh/g).展开更多
Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,a...Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.展开更多
The novel Co-based superalloys are extensively used in gas-powered and jet engine turbines due to their excellent high-temperature performance, achieved by strengthening the L12-γ′ ordered phase. This review present...The novel Co-based superalloys are extensively used in gas-powered and jet engine turbines due to their excellent high-temperature performance, achieved by strengthening the L12-γ′ ordered phase. This review presents an overview of the research progress on oxidation behavior of Co-based superalloys, including oxidation kinetics, oxides morphology, the formation and spallation of oxide layers, and importantly, the synergistic effects of alloying elements on oxidation resistance—a critical area considering the complex interactions with multiple alloying elements. Additionally, this review compares the oxidation resistance of single crystal versus polycrystalline alloys. The effect of phase interface and dislocations on oxidation behavior is also discussed. While significant progress has been achieved, areas necessitating further investigation include optimizing alloy compositions for enhanced oxidation resistance and understanding the long-term stability of oxide layers. The future prospects for Co-based superalloys are promising as ongoing research aims to address the existing challenges and unlock new applications at even higher operating temperatures.展开更多
Traumatic brain injury involves complex pathophysiological mechanisms,among which oxidative stress significantly contributes to the occurrence of secondary injury.In this study,we evaluated hypidone hydrochloride(YL-0...Traumatic brain injury involves complex pathophysiological mechanisms,among which oxidative stress significantly contributes to the occurrence of secondary injury.In this study,we evaluated hypidone hydrochloride(YL-0919),a self-developed antidepressant with selective sigma-1 receptor agonist properties,and its associated mechanisms and targets in traumatic brain injury.Behavioral experiments to assess functional deficits were followed by assessment of neuronal damage through histological analyses and examination of blood-brain barrier permeability and brain edema.Next,we investigated the antioxidative effects of YL-0919 by assessing the levels of traditional markers of oxidative stress in vivo in mice and in vitro in HT22 cells.Finally,the targeted action of YL-0919 was verified by employing a sigma-1 receptor antagonist(BD-1047).Our findings demonstrated that YL-0919 markedly improved deficits in motor function and spatial cognition on day 3 post traumatic brain injury,while also decreasing neuronal mortality and reversing blood-brain barrier disruption and brain edema.Furthermore,YL-0919 effectively combated oxidative stress both in vivo and in vitro.The protective effects of YL-0919 were partially inhibited by BD-1047.These results indicated that YL-0919 relieved impairments in motor and spatial cognition by restraining oxidative stress,a neuroprotective effect that was partially reversed by the sigma-1 receptor antagonist BD-1047.YL-0919 may have potential as a new treatment for traumatic brain injury.展开更多
Engineering nanomaterials at single-atomic sites could enable unprecedented catalytic properties for broad applications,yet it remains challenging to do so on the surface of multimetallic nanocrystals.Herein,we presen...Engineering nanomaterials at single-atomic sites could enable unprecedented catalytic properties for broad applications,yet it remains challenging to do so on the surface of multimetallic nanocrystals.Herein,we present the multifactorial engineering(size,shape,phase,and composition)of the fully ordered PtBi nanoplates at atomic level,achieving a unique catalyst surface where the face-centered cubic(fcc)Pt edges are modified by the isolated Pd atoms and BiO_(x)adatoms.This Pd_(1)/Pt-BiO_(x)electrocatalyst exhibits an ultrahigh mass activity of 16.01 A mg^(-1)Pt+Pd toward ethanol oxidation in alkaline electrolyte and enables a direct ethanol fuel cell of peak power density of 56.7 mW cm^(−2).The surrounding BiO_(x)adatoms are critical for mitigating CO-poisoning on the Pt surface,and the Pd_(1)/Pt single-atom alloy further facilitates the electrooxidation of CH_(3)CH_(2)OH.This work offers new insights into the rational design and construction of sophisticated catalyst surface at single-atomic sites for highly efficient electrocatalysis.展开更多
基金National Natural Science Foundation of China(52071274)Key Research and Development Projects of Shaanxi Province(2023-YBGY-442)Science and Technology Nova Project-Innovative Talent Promotion Program of Shaanxi Province(2020KJXX-062)。
文摘To mitigate the impact of interdiffusion reactions between the silicide slurry and Ta12W alloy substrate during vacuum sintering process on the oxidation resistance of the silicide coating,a micro-arc oxidation pretreatment was employed to construct a Ta_(2)O_(5)ceramic layer on the Ta12W alloy surface.Subsequently,a slurry spraying-vacuum sintering method was used to prepare a Si-Cr-Ti-Zr coating on the pretreated substrate.Comparative studies were conducted on the microstructure,phase composition,and isothermal oxidation resistance(at 1600℃)of the as-prepared coatings with and without the micro-arc oxidation ceramic layer.The results show that the Ta_(2)O_(5)layer prepared at 400 V is more continuous and has smaller pores than that prepared at 350 V.After microarc oxidation pretreatment,the Si-Cr-Ti-Zr coating on Ta12W alloy consists of three distinct layers:an upper layer dominated by Ti_(5)Si_(3),Ta_(5)Si_(3),and ZrSi;a middle layer dominated by TaSi_(2);a coating/substrate interfacial reaction layer dominated by Ta_(5)Si_(3).Both the Si-Cr-Ti-Zr coatings with and without the Ta_(2)O_(5)ceramic layer do not fail after isothermal oxidation at 1600℃for 5 h.Notably,the addition of the Ta2O5 ceramic layer reduces the high-temperature oxidation rate of the coating.
基金supported by the National Key Research and Development Program of China(2024YFA1612900)the National Natural Science Foundation of China(Grant No.52103365 and No.12375270)the Guangdong Innovative and Entrepreneurial Research Team Program,China(Grant No.2021ZT09L227).
文摘Fine-grained nuclear graphite is a key material in high-temperature gas-cooled reactors(HTGRs).During air ingress accidents,core graphite components undergo severe oxidation,threatening structural integrity.Therefore,understanding the oxidation behavior of nuclear graphite is essential for reactor safety.The influence of oxidation involves multiple factors,including temperature,sample size,oxidant,impurities,filler type and size,etc.The size of the filler particles plays a crucial role in this study.Five ultrafine-and superfine-grained nuclear graphite samples(5.9-34.4μm)are manufactured using identical raw materials and manufacturing processes.Isothermal oxidation tests conducted at 650℃-750℃ are used to study the oxidation behavior.Additionally,comprehensive characterization is performed to analyze the crystal structure,surface morphology,and nanoscale to microscale pore structure of the samples.Results indicate that oxidation behavior cannot be predicted solely based on filler grain size.Reactive site concentration,characterized by active surface area,dominates the chemical reaction kinetics,whereas pore tortuosity,quantified by the structural parameterΨ,plays a key role in regulating oxidant diffusion.These findings clarify the dual role of microstructure in oxidation mechanisms and establish a theoretical and experimental basis for the design of high-performance nuclear graphite capable of long-term service in high-temperature gas-cooled reactors.
基金supported by the National Natural Science Foundation of China(Nos.42477406 and 51878617)the Horizontal Scientific Research Project(No.KYY-HX-20220803)the Engineering Research Center of Ministry of Education for Renewable Energy Infrastructure Construction Technology.
文摘In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti-mization,for the degradation of landfill leachate(LL)containing elevated levels of tetracycline(TC),and explored its mechanism of action.Firstly,titanium-based ruthenium-iridium(Ti/RuO_(2)-IrO_(2)),titanium-based ruthenium-iridium-platinum(Ti/Pt-RuO_(2)-IrO_(2)),and titanium-based tin-antimony(Ti/SnO_(2)-Sb_(2)O_(3))were employed as an-odes in the electrocatalytic oxidation system,with titanium and stainless steel plates serving as cathodes,to construct the optimal two-dimensional electrocatalytic oxidation system(2D-ECO)through cross-comparison ex-periments.Subsequently,using granular activated carbon(GAC),coconut shell biochar(CBC),walnut shell carbon(WBC),and bamboo charcoal(BBC)as particle electrodes,a 3D-ECO system was developed.The influence of var-ious operational parameters on treating TC-containing LL was investigated.The optimal operating parameters obtained from the study was:pH=5,current density of 30 mA/cm^(2),particle dosage of 7 g/L,particle size ranging from 1.70 to 2.00 mm,and electrode spacing of 4 cm.Under these conditions,the COD removal rate of 3D-ECO within three hours was 90.25%,the TC removal rate was 72.41%,and the NH_(3)-N removal rate was 39.52%.The removal of TC followed a pseudo-first-order kinetic model.Additionally,degradation mechanisms were elucidated through electron paramagnetic resonance(EPR)spectrometer and Tert-Butanol(TBA)quenching experiments,indicating that the degradation primarily occurred through a non-radical(1O_(2))pathway.This re-search offers a comprehensive analysis of the simultaneous breakdown of intricate LL matrices and TC,enhancing our comprehension of the degradation processes and underlying mechanisms.
基金Supported by the National Natural Science Foundation of China （20576081, 20736009） and the Ph.D. Programs Foundation of Ministry of Education of China （20070610128）.
文摘Liquid phase oxidation of toluene is an environmental benign route for the production of benzoic acid.In a φ48mm bubble column reactor,the commercial process of toluene liquid phase oxidation was conducted with Co(CH3COO)2.4H2O as catalyst.The Co2+ concentration [Co2+] was determined by extraction spectrophotometry and hereby the Co3+ concentration [Co3+] was obtained by mass balance.The results showed that [Co3+] reached the maximum at about 25-30min.[Co3+] increased with increasing Co catalyst amount at total Co concentration<150 mg.L-1 of toluene.The conversion of toluene,yield and selectivity of benzoic acid increased with the increasing [Co3+/Co2+] max.A high [Co3+] and a high [Co3+]/[Co2+] ratio are beneficial to the reaction.
文摘The latest progress and developments in catalysts for the oxidation of cyclohexane are reviewed. Catalytic systems for the oxidation of cyclohexane including metal supported, metal oxides, molecular sieves, metal substituted polyoxometalates, photocatalysts, orga nocatalysts, Gif systems, metal-organic catalysts and metalloporphyrins are discussed with a particular emphasis on metalloporphyrin catalytic systems. The advantages and disadvantages of these methods are summarized and analyzed. Finally, the development trends in the oxidation technology of cyclohexane are examined.
基金supported by the Original Exploratory Program of the National Natural Science Foundation of China(No.52450012)。
文摘TiB_(2)coatings can significantly enhance the high-temperature oxidation resistance of molybdenum,which would broaden the application range of molybdenum and alloys thereof.However,traditional methods for preparing TiB_(2)coatings have disadvantages such as high equipment costs,complicated processes,and highly toxic gas emissions.This paper proposes an environmentally friendly method,which requires inexpensive equipment and simple processing,for preparing TiB_(2)coating on molybdenum via electrophoretic deposition within Na3AlF6-based molten salts.The produced TiB_(2)layer had an approximate thickness of 60μm and exhibited high density,outstanding hardness(38.2 GPa)and robust adhesion strength(51 N).Additionally,high-temperature oxidation experiments revealed that,at900℃,the TiB_(2)coating provided effective protection to the molybdenum substrate against oxidation for 3 h.This result indicates that the TiB_(2)coating prepared on molybdenum using molten salt electrophoretic deposition possesses good high-temperature oxidation resistance.
基金the financial support from the National Natural Science Foundation of China(52172110,52472231,52311530113)Shanghai"Science and Technology Innovation Action Plan"intergovernmental international science and technology cooperation project(23520710600)+1 种基金Science and Technology Commission of Shanghai Municipality(22DZ1205600)the Central Guidance on Science and Technology Development Fund of Zhejiang Province(2024ZY01011)。
文摘Investigating structural and hydroxyl group effects in electrooxidation of alcohols to value-added products by solid-acid electrocatalysts is essential for upgrading biomass alcohols.Herein,we report efficient electrocatalytic oxidations of saturated alcohols(C_(1)-C_(6))to selectively form formate using Ni Co hydroxide(Ni Co-OH)derived Ni Co_(2)O_(4)solid-acid electrocatalysts with balanced Lewis acid(LASs)and Brønsted acid sites(BASs).Thermal treatment transforms BASs-rich(89.6%)Ni Co-OH into Ni Co_(2)O_(4)with nearly equal distribution of LASs(53.1%)and BASs(46.9%)which synergistically promote adsorption and activation of OH-and alcohol molecules for enhanced oxidation activity.In contrast,BASs-enriched Ni Co-OH facilitates formation of higher valence metal sites,beneficial for water oxidation.The combined experimental studies and theoretical calculation imply the oxidation ability of C1-C6alcohols increases as increased number of hydroxyl groups and decreased HOMO-LUMO gaps:methanol(C_(1))<ethylene glycol(C_(2))<glycerol(C3)<meso-erythritol(C4)<xylitol(C5)<sorbitol(C6),while the formate selectivity shows the opposite trend from 100 to 80%.This study unveils synergistic roles of LASs and BASs,as well as hydroxyl group effect in electro-upgrading of alcohols using solid-acid electrocatalysts.
文摘Pt/CeO2–ZrO2–SnO2/γ-Al2O3 catalysts were prepared by co-precipitation and wet impregnation methods for catalytic oxidation of acetaldehyde to acetic acid in water. In the present catalysts, Pt and CeO2–ZrO2–SnO2 were successfully dispersed on the γ-Al2O3 support.Dependences of platinum content and reaction time on the selective oxidation of acetaldehyde to acetic acid were investigated to optimize the reaction conditions for obtaining both high acetaldehyde conversion and highest selectivity to acetic acid. Among the catalysts, a Pt（6.4 wt.%）/Ce0.68Zr0.17Sn0.15O2.0（16 wt.%）/γ-Al2O3 catalyst showed the highest acetaldehyde oxidation activity. On this catalyst, acetaldehyde was completely oxidized after the reaction at 0°C for 8 hr, and the selectivity to acetic acid reached to 95%and higher after the reaction for 4 hr and longer.
文摘Liquid-phase oxidation of toluene with air has become the main technology for producing benzoic acid in a reactor at present. Based on the kinetic model of the toluene oxidation process obtained from laboratory and mass balance of key component, a novel model is established to simulate the industrial toluene oxidation process, in which the effects of benzaldehyde and benzyl alcohol are considered and the kinetic parameters are revised by industrial data. The simulation results show that the error of benzoic acid yield is within 3.5%. Based on the simulation model, to maximize the benzoic acid yield, an optimization model is proposed to optimize the operating parameters, including toluene feed-in mass flux and temperature. The optimization result indicates that on the allowable operating conditions the maximum benzoic acid yield obtained with the reaction temperature at 167.2 C an the mass flux at 104.1 t·h^- 1 is greater than the current one, which can be used to guide industrial reactor s operation.
基金supported by the National Natural Science Foundation of China (No. 21376163)
文摘In this study, liquid-phase aerobic oxidation of toluene catalyzed by Mn–Mo oxide was conducted in a 1.0 L batch reactor. The macroscopic kinetics of toluene consumption and benzaldehyde generation at 413–443 K were obtained from a combination of experimental observation and hypothetical models. The results clearly showed that both the oxidation rate of toluene and generation rate of the aromatic product were proportional to the concentration of the substrate, the partial pressure of oxygen and the surface area of the catalyst. The energy barrier of toluene oxidation to benzyl alcohol was the highest(≈ 81 kJ mol^(-1)), while that of benzyl alcohol oxidation to benzaldehyde was the lowest(≈ 57 kJ mol^(-1)). Moreover, the activation energy of further oxidation of benzaldehyde in an acetic acid solvent was only slightly lower(≈ 1.9 kJ mol^(-1)) than that of toluene oxidation. Significantly, the transformation of benzyl alcohol indeed contributed to the generation of benzaldehyde and this step conformed to a first-order parallel-consecutive model. Increased reaction temperature and residence time favored the transformation of benzyl alcohol to benzaldehyde. In addition, doping with molybdenum at Mn/Mo = 3/1 enhanced the catalytic performance of the heterogeneous catalyst and was attributed to the presence of a synergetic effect between different metal cations. Regarding the microscopic kinetics, the LH-OS-ND mechanism(Langmuir–Hinshelwood adsorption of reagents on the same type of active sites and non-dissociative adsorption of oxygen) was verified as responsible for the heterogeneous oxidation of toluene. Oxygen and benzaldehyde were weakly adsorbed(Δ H_(ads,Oxy) ≈^(-1)5 kJ mol^(-1), Δ H _(ads)0,Bald) ≈-30 kJ mol^(-1)), but showed strong mobility(Δ S_(ads,Oxy) ≈-22 J mol^(-1) K^(-1)), Δ S_(ads,Bald) ≈-39 J mol^(-1) K^(-1)). The fundamental intrinsic rates were deduced based on the LH-OS-ND mechanism and showed great consistency with the macroscopic results.
基金Supported by the Natural National Science Foundation of China （20080672） and the Research Fund for the Doctoral Program of Higher Education of China （200803351111）.
文摘During the liquid-phase oxidation of p-xylene,over-oxidation of reactant,intermediates and solvent to carbon dioxide and carbon monoxide is generally known as the burning side reaction.Batch and semi-continuous experiments were carried out,and the experimental data of the burning side reaction were analyzed and reported in this paper.The results showed that the rates of burning side reactions were proportional to the rates of the main reaction,but decreased with the increasing concentrations of reactant and intermediates.The inter-stimulative and competitive relationship between the burning side reaction and the main reaction was confirmed,and the rates of the burning side reaction could be described with some key indexes of the main reaction.According to the mechanism of the side reactions and the kinetics model of main reaction which were proposed and tested in the previous papers,a kinetic model of the burning side reactions involving some key indexes of the main reaction was developed,and the parameters were determined by data fitting of the COx rate curves.The obtained kinetic model could describe the burning side reactions adequately.
文摘The effect of liquid-phase oxidation impurities on the solubility of water in hydrocarbon fuels was studied.The results show that the concentration of polar surfactant molecules in the first region increases(true solution)during fuel oxidation,and since the oxidation groups(-COOH,-O=O,-OH,etc.)have similar dipole momentμ,the dielectric loss tangent tanδincreases linearly in this region with surfactant concentration.Upon further oxidation,micelle structures begin to form at a certain point.Micelle formation leads to a sharp decrease in the dipole moment attributable to the monomer unitμ/n,where nis the number of molecules in a micelle.A several-fold decrease in the dipole moment leads to a sharp drop in tanδ.Upon further increase in the number and size of micelles,the dipole moment remains practically unchanged,and the dielectric loss tangent begins to increase linearly again with surfactant concentration.If the critical concentration for micelle formation is achieved upon further oxidation of hydrocarbon liquids,micelle formation processes occur spontaneously in the solution,and the true solution becomes a colloidal system(sol).The resulting micelles are structured with hydrocarbon radicals of molecules toward the outside and hydrophilic(polar)groups toward the inside.Water molecules are located inside micelles and held so securely that water molecules do not aggregate as temperature decreases.The reason for significant differences in the equilibrium solubility of water in hydrocarbon fuels is the different oxidation factors of product samples,resulting from the accumulation of various concentrations of oxidation products,which are natural surfactants,in hydrocarbon fuels.
文摘The selective oxidation of methanol to methyl formate is one of the most attractive processes to obtain value-added methanol-downstream products.The development of highly efficient and stable catalysts is critical for this transformation.In this study,a series of MIL-88B(Fe_(x),Co_(1‒x))bimetallic catalysts with different Fe/Co molar ratios were prepared through a one-pot hydrothermal method.X-ray diffraction,scanning electron microscopy,high-resolution transmission electron microscopy,energy dispersive spectroscopy,Fourier transform infrared spectroscopy,X-ray photoelectron spectroscopy,N2 adsorption-desorption,and inductively coupled plasma-mass spectrometry characterization were performed to elucidate the structure of the catalysts.The activity of the catalysts were assessed in the one-step oxidation of methanol to methyl formate with H_(2)O_(2)in a liquid-phase batch reactor.The results show that the MIL-88B(Fe_(x),Co_(1‒x))catalysts exhibit uniform needle-like morphologies with an average length and width of 400-600 nm and 100-150 nm,respectively.Co^(2+)is incorporated into the framework by partially replacing Fe^(3+)in MIL-88B.Moreover,the catalyst efficiently promoted the conversion of methanol to methyl formate.When MIL-88B(Fe_(0.7),Co_(0.3))catalyst was used with a molar ratio of H_(2)O_(2)to methanol of 0.5 at 80℃for 60 min,34.8%methanol conversion was achieved,and the selectivity toward methyl formate was 67.6%.The catalysts also showed great stability with a steady conversion and selectivity even after four cycles.The preliminary oxidation mechanism was also studied.It was determined that H_(2)O_(2)is first adsorbed on the Fe^(3+)sites and subsequently activates these sites.Methanol is adsorbed by the O atoms of the framework through hydrogen bonding and is gradually oxidized to formic acid.Subsequently,formic acid reacts with the residual methanol at the Fe^(3+)and Co^(2+)Lewis acid sites to form methyl formate.
基金Project(2008ZX07105-002) supported by the Erhai Lake Project of National Science and Technology Major Project in the 11th Five years Plan of China
文摘Hydrogen sulfide in rural biogas was removed with liquid-phase catalytic oxidation.By using rare earth as catalyst,and sulfosalicylic acid as stabilizer,H2S purification efficiency could increase as high as 96%,and sulfur capacity of the composite solution was about 3 g/L.The results show that purification efficiency was affected by catalyst addition,pH,experimental temperature,and sulfur capacity.The parameters effects on catalytic oxidation were studied,and the optimized conditions were that Fe3+ concentration 0.08 mg/L,reaction temperature 70°C,pH 9.0,with a absorption solution volume of 50 mL,a gas flow rate 200 mL/min,and H2S mass concentration of 1.58-2.02 mg/m3.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFF0609000)National Natural Science Foundation of China(Grant Nos.52171034 and 52101037)Postdoctoral Fellowship Program of CPSFara(No.GZB20230944).
文摘Up-and-coming high-temperature materials,refractory high entropy alloys,are suffering from lower oxidation resistance,restricting their applications in the aerospace field.In this study,two novel treatments of Al-deposited and remelted were developed to refine the microstructure and enhance the oxidation resistance of refractory high entropy alloy using electron beam freeform fabrication(EBF3).Finer and short-range ordering structures were observed in the remelted sample,whereas the Al-deposited sample showcased the formation of silicide and intermetallic phases.High-temperature cyclic and isothermal oxidation tests at 1000℃ were carried out.The total weight gain after 60 h of cyclic oxidation decreased by 17.49%and 30.46%for the remelted and deposited samples,respectively,compared to the as-cast state.Oxidation kinetics reveal an evident lower mass gain and oxidation rate in the treated samples.A multilayer oxide consisting of TiO_(2)+Al_(2)O_(3)+SiO_(2)+AlNbO_(4) was studied for its excellent oxidation resistance.The oxidation behavior of rutile,corundum and other oxides was analyzed using first principles calculations and chemical defect analysis.Overall,this research,which introduces novel treatments,offers promising insights for enhancing the inherent oxidation resistance of refractory high entropy alloys.
文摘Pitch produced by the lique-faction of coal was divided into two frac-tions:soluble in toluene(TS)and insol-uble in toluene but soluble in pyridine(TI-PS),and their differences in molecu-lar structure and oxidation activity were studied.Several different carbon materi-als were produced from them by oxida-tion in air(350℃,300 mL/min)fol-lowed by carbonization(1000℃ in Ar),and the effect of the cross-linked structure on their structure and sodium storage properties was investigated.The results showed that the two pitch fractions were obviously different after the air oxidation.The TS fraction with a low degree of condensation and abundant side chains had a stronger oxidation activity and thus introduced more cross-linked oxygen-containing functional groups C(O)―O which prevented carbon layer rearrangement during the carbonization.As a result,a disordered hard carbon with more defects was formed,which improved the electrochemical performance.Therefore,the carbon materials derived from TS(O-TS-1000)had an obvious disordered structure and a larger layer spacing,giving them better sodium storage perform-ance than those derived from the TI-PS fraction(O-TI-PS-1000).The specific capacity of O-TS-1000 was about 250 mAh/g at 20 mA/g,which was 1.67 times higher than that of O-TI-PS-1000(150 mAh/g).
基金National Natural Science Foundation of China(52071126)Natural Science Foundation of Tianjin City,China(22JCQNJC01240)+2 种基金Central Guidance on Local Science and Technology Development Fund of Hebei Province(226Z1009G)Special Funds for Science and Technology Innovation in Hebei(2022X19)Anhui Provincial Natural Science Foundation(2308085ME135)。
文摘Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.
基金support from the National Natural Science Foundation of China(Nos.52171107,52201203)the Hebei Provincial Natural Science Foundation,China(No.E2021501026)the National Natural Science Foundation of China-Joint Fund of Iron and Steel Research(No.U1960204).
文摘The novel Co-based superalloys are extensively used in gas-powered and jet engine turbines due to their excellent high-temperature performance, achieved by strengthening the L12-γ′ ordered phase. This review presents an overview of the research progress on oxidation behavior of Co-based superalloys, including oxidation kinetics, oxides morphology, the formation and spallation of oxide layers, and importantly, the synergistic effects of alloying elements on oxidation resistance—a critical area considering the complex interactions with multiple alloying elements. Additionally, this review compares the oxidation resistance of single crystal versus polycrystalline alloys. The effect of phase interface and dislocations on oxidation behavior is also discussed. While significant progress has been achieved, areas necessitating further investigation include optimizing alloy compositions for enhanced oxidation resistance and understanding the long-term stability of oxide layers. The future prospects for Co-based superalloys are promising as ongoing research aims to address the existing challenges and unlock new applications at even higher operating temperatures.
基金supported by the National Natural Science Foundation of China,Nos.82204360(to HM)and 82270411(to GW)National Science and Technology Innovation 2030 Major Program,No.2021ZD0200900(to YL)。
文摘Traumatic brain injury involves complex pathophysiological mechanisms,among which oxidative stress significantly contributes to the occurrence of secondary injury.In this study,we evaluated hypidone hydrochloride(YL-0919),a self-developed antidepressant with selective sigma-1 receptor agonist properties,and its associated mechanisms and targets in traumatic brain injury.Behavioral experiments to assess functional deficits were followed by assessment of neuronal damage through histological analyses and examination of blood-brain barrier permeability and brain edema.Next,we investigated the antioxidative effects of YL-0919 by assessing the levels of traditional markers of oxidative stress in vivo in mice and in vitro in HT22 cells.Finally,the targeted action of YL-0919 was verified by employing a sigma-1 receptor antagonist(BD-1047).Our findings demonstrated that YL-0919 markedly improved deficits in motor function and spatial cognition on day 3 post traumatic brain injury,while also decreasing neuronal mortality and reversing blood-brain barrier disruption and brain edema.Furthermore,YL-0919 effectively combated oxidative stress both in vivo and in vitro.The protective effects of YL-0919 were partially inhibited by BD-1047.These results indicated that YL-0919 relieved impairments in motor and spatial cognition by restraining oxidative stress,a neuroprotective effect that was partially reversed by the sigma-1 receptor antagonist BD-1047.YL-0919 may have potential as a new treatment for traumatic brain injury.
基金supported by the National Natural Science Foundation of China(NSFC)(Grant Nos.22475132 and 52101259)the Shenzhen Science and Technology Innovation Committee(Grant No.JCYJ20210324105008022)financially supported by the Shenzhen Science and Technology Innovation Program(Nos.KQTD20190929173914967 and ZDSYS20220527171401003).
文摘Engineering nanomaterials at single-atomic sites could enable unprecedented catalytic properties for broad applications,yet it remains challenging to do so on the surface of multimetallic nanocrystals.Herein,we present the multifactorial engineering(size,shape,phase,and composition)of the fully ordered PtBi nanoplates at atomic level,achieving a unique catalyst surface where the face-centered cubic(fcc)Pt edges are modified by the isolated Pd atoms and BiO_(x)adatoms.This Pd_(1)/Pt-BiO_(x)electrocatalyst exhibits an ultrahigh mass activity of 16.01 A mg^(-1)Pt+Pd toward ethanol oxidation in alkaline electrolyte and enables a direct ethanol fuel cell of peak power density of 56.7 mW cm^(−2).The surrounding BiO_(x)adatoms are critical for mitigating CO-poisoning on the Pt surface,and the Pd_(1)/Pt single-atom alloy further facilitates the electrooxidation of CH_(3)CH_(2)OH.This work offers new insights into the rational design and construction of sophisticated catalyst surface at single-atomic sites for highly efficient electrocatalysis.
