The distributions of light and nitrogen within a plant's canopy reflect the growth adaptation of crops to the environment and are conducive to improving the carbon assimilation ability.So can the yield in crop pro...The distributions of light and nitrogen within a plant's canopy reflect the growth adaptation of crops to the environment and are conducive to improving the carbon assimilation ability.So can the yield in crop production be maximized by improving the light and nitrogen distributions without adding any additional inputs?In this study,the effects of different nitrogen application rates and planting densities on the canopy light and nitrogen distributions of two highyielding maize cultivars(XY335 and DH618)and the regulatory effects of canopy physiological characteristics on radiation use efficiency(RUE)and yield were studied based on high-yield field experiments in Qitai,Xinjiang Uygur Autonomous Region,China,during 2019 and 2020.The results showed that the distribution of photosynthetically active photon flux density(PPFD)in the maize canopy decreased from top to bottom,while the vertical distribution of specific leaf nitrogen(SLN)initially increased and then decreased from top to bottom in the canopy.When SLN began to decrease,the PPDF values of XY335 and DH618 were 0.5 and 0.3,respectively,corresponding to 40.6 and49.3%of the total leaf area index(LAI).Nitrogen extinction coefficient(K_(N))/light extinction coefficient(K_(L))ratio in the middle and lower canopy of XY335(0.32)was 0.08 higher than that of DH618(0.24).The yield and RUE of XY335(17.2 t ha^(-1)and 1.8g MJ^(-1))were 7.0%(1.1 t ha^(-1))and 13.7%(0.2 g MJ^(-1))higher than those of DH618(16.1 t ha^(-1)and 1.6 g MJ^(-1)).Therefore,better light conditions(where the proportion of LAI in the upper and middle canopy was small)improved the light distribution when SLN started to decline,thus helping to mobilize the nitrogen distribution and maintain a high K_(N)and K_(N)/K_(L)ratio.In addition,K_(N)/K_(L)was a key parameter for yield improvement when the maize nutrient requirements were met at 360 kg N ha^(-1).At this level,an appropriately optimized high planting density could promote nitrogen utilization and produce higher yields and greater efficiency.The results of this study will be important for achieving high maize yields and the high efficiency cultivation and breeding of maize in the future.展开更多
Semitransparent organic photovoltaics(ST-OPVs)for building integration represent a pivotal direction in the development of photovoltaic industry.Solution-processed silver nanowires(AgNWs)are considered promising candi...Semitransparent organic photovoltaics(ST-OPVs)for building integration represent a pivotal direction in the development of photovoltaic industry.Solution-processed silver nanowires(AgNWs)are considered promising candidates for transparent electrodes in semitransparent devices due to their high transparency-conductivity-efficiency merit,large-scale processability,and low cost.In this work,we develop two solution-processed organic–inorganic hybrid electrodes,named AgNWs-PD and AgNWsPC,utilizing AgNWs as the conductive framework and aliphatic amine-functionalized perylene-diimide(PDINN)as the sandwiched material,while AgNWs-PC exhibits significantly improved electrical conductivity and enhanced contact area with the underlying electron transport layer.The optimized device achieves a power conversion efficiency of 9.45%with an open circuit voltage of 0.846 V,a high filling factor of 75.4%,and an average visible transmittance(AVT)of 44.0%,delivering an outstanding light utilization efficiency(LUE)of 4.16%,which is the highest reported value for all solution-processed ST-OPVs.In addition,by coupling a 30-nm tellurium dioxide atop AgNWs-PC,the bifaciality factor of derivative devices improves from 73.7%to 99.4%,while maintaining a high bifacial LUE over 3.7%.Our results emphasize the superiority and effectiveness of PDINN-sandwiched AgNWs electrodes for highperformance and all solution-processed ST-OPVs.展开更多
Gross primary production(GPP)is a crucial indicator representing the absorption of atmospheric CO_(2) by vegetation.At present,the estimation of GPP by remote sensing is mainly based on leaf-related vegetation indexes...Gross primary production(GPP)is a crucial indicator representing the absorption of atmospheric CO_(2) by vegetation.At present,the estimation of GPP by remote sensing is mainly based on leaf-related vegetation indexes and leaf-related biophysical para-meter leaf area index(LAI),which are not completely synchronized in seasonality with GPP.In this study,we proposed chlorophyll content-based light use efficiency model(CC-LUE)to improve GPP estimates,as chlorophyll is the direct site of photosynthesis,and only the light absorbed by chlorophyll is used in the photosynthetic process.The CC-LUE model is constructed by establishing a linear correlation between satellite-derived canopy chlorophyll content(Chlcanopy)and FPAR.This method was calibrated and validated utiliz-ing 7-d averaged in-situ GPP data from 14 eddy covariance flux towers covering deciduous broadleaf forest ecosystems across five dif-ferent climate zones.Results showed a relatively robust seasonal consistency between Chlcanopy with GPP in deciduous broadleaf forests under different climatic conditions.The CC-LUE model explained 88% of the in-situ GPP seasonality for all validation site-year and 56.0% of in-situ GPP variations through the growing season,outperforming the three widely used LUE models(MODIS-GPP algorithm,Vegetation Photosynthesis Model(VPM),and the eddy covariance-light use efficiency model(EC-LUE)).Additionally,the CC-LUE model(RMSE=0.50 g C/(m^(2)·d))significantly improved the underestimation of GPP during the growing season in semi-arid region,re-markably decreasing the root mean square error of averaged growing season GPP simulation and in-situ GPP by 75.4%,73.4%,and 37.5%,compared with MOD17(RMSE=2.03 g C/(m^(2)·d)),VPM(RMSE=1.88 g C/(m^(2)·d)),and EC-LUE(RMSE=0.80 g C/(m^(2)·d))model.The chlorophyll-based method proved superior in capturing the seasonal variations of GPP in forest ecosystems,thereby provid-ing the possibility of a more precise depiction of forest seasonal carbon uptake.展开更多
Glass substrates which realize high out-coupling efficiency OLEDs （organic light emitting diodes） were developed. A scattering layer whose matrix was made of high refractive index glass was formed on a glass substra...Glass substrates which realize high out-coupling efficiency OLEDs （organic light emitting diodes） were developed. A scattering layer whose matrix was made of high refractive index glass was formed on a glass substrate, and pores in the glass matrix work as scattering centers. The out-coupling efficiency of an OLED using this substrate is 1.8 times higher compared with an OLED using an untreated glass substrate. Furthermore angular dependency of the color and color variation between panels can be successfully suppressed.展开更多
This study presents a detailed comparative analysis of three electron transport layer(ETL)materials for perovskite solar cells(PSCs),namely titanium dioxide(TiO_(2)),barium titanate(BaTiO_(3)or BTO),and strontium-dope...This study presents a detailed comparative analysis of three electron transport layer(ETL)materials for perovskite solar cells(PSCs),namely titanium dioxide(TiO_(2)),barium titanate(BaTiO_(3)or BTO),and strontium-doped barium titan-ate(Ba_(1−x)Sr_(x)TiO_(3)or BST),and their impact on the quantum efficiency(QE)and power conversion efficiency(PCE)of CH_(3)NH_(3)PbI_(3)(MAPbI_(3))PSCs.The optimized structure demonstrates that devices utilizing BST as an ETL achieved the highest PCE of 29.85%,exhibiting superior thermal stability with the lowest temperature coefficient of−0.43%/K.This temperature-induced degradation is comparable to that of commercially available silicon cells.Furthermore,BST-based ETLs show 29.50%and 26.48%higher PCE than those of TiO_(2)-based and BTO-based ETLs.The enhanced internal QE and favorable current density–voltage(J–V)characteristics of BST compared with those of TiO_(2)and BTO are attributed to its improved charge carrier separation,reduced recombination rates,and robust electrical characteristics under varied environmental conditions.Furthermore,the electric field and generation rate of the BST-based ETLs show a more favorable distribution than those of the TiO_(2)-based and BTO-based ETLs.These findings provide significant insights into the role of different ETLs in enhancing QE,indicating that BST is a superior ETL that enhances both the efficiency and stability of PSCs.This study contributes to the understanding of how perovskite-structured ETLs can be used to design and optimize highly efficient and stable photovoltaic devices.展开更多
Solid-state lighting is now developing toward high-power and super-brightness,but is largely limited by the lack of highly robust and efficient color conversion materials that can be survived from high-power or high-p...Solid-state lighting is now developing toward high-power and super-brightness,but is largely limited by the lack of highly robust and efficient color conversion materials that can be survived from high-power or high-power density excitation,typically the red-emitting ones.In this work,we fabricated highly effi-cient and pore-free Sr_(0.5)Ca_(0.5)AlSiN_(3)∶Eu^(2+)(SCASN)red-emitting ceramics by spark plasma sintering of fine phosphor powders.These fine phosphor powders were prepared by treating the commercial phosphors with high-energy ball-milling,centrifugation and acid washing,leading to a particle size of 2.55μm and an internal quantum efficiency as high as 74.0%under 450 nm excitation.The phosphor powders can be densified into SCASN ceramics without using sintering additives at a temperature as low as 1475℃,and the ceramics show an internal quantum efficiency of 75.3%,which is 50%higher than those ceram-ics fabricated with untreated commercial powders.When excited by a high-power blue LED at a current density of 4 A/mm^(2),the SCASN ceramics have a maximum luminous flux of 660 lm(i.e.,26 Mcd/m^(2)).The phosphor ceramics can also withstand a high laser power density of 15.7 W/mm^(2),and exhibit an output luminance of 188 Mcd/m^(2).This work provides a general method to prepare fine phosphor powders that enable to fabricate high efficiency phosphor ceramics used in high-power solid-state lighting.展开更多
High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）：...High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）： tetrafluoro-tetracyanoqino dimethane （F4-TCNQ）/N,N-di（naphthalene-1-yl）-N,N-diphenyl-benzidine （NPB）/ 4,4-N,N-dicarbazolebiphenyl （CBP）： iridium （III） diazine complexes （MPPZ） 2 Ir（acac）/NPB/2-methyl-9,10-di（2-naphthyl）anthracene （MADN）： p-bis（p-N,N-di-phenyl-aminostyryl）benzene （DSA-ph）/bis（10-hydroxybenzo[h] quino-linato）beryllium complex （Bebq2）/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l’Eclairage （CIE） chromaticity coordinates are almost constant during a large voltage change of 6–12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.展开更多
The reasons for low output power of AlGalnP Light Emitting Diodes （LEDs） have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especiall...The reasons for low output power of AlGalnP Light Emitting Diodes （LEDs） have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especially at a large injected current which would reduce both the internal and external quantum efficiencies. Two kinds of LEDs with the same active region but different window layers have been fabricated. The new window layer composed of textured 0.5 μm GaP and thin Indium-Tin-Oxide film has shown that low external quantum efficiency （EQE） has serious impaction on the internal quantum efficiency （IQE）, because the carrier distribution will change with the body temperature increasing due to the heat inside, and the test results have shown the evidence of LEDs with lower output power and bigger wavelength red shift.展开更多
An organic light-emitting diode （OLED） device with high efficiency and brightness is fabricated by inserting CuOJCu dual inorganic buffer layers between indium-tin-oxide （ITO） and hole-transport layer （HTL）. The...An organic light-emitting diode （OLED） device with high efficiency and brightness is fabricated by inserting CuOJCu dual inorganic buffer layers between indium-tin-oxide （ITO） and hole-transport layer （HTL）. The CuOx/Cu buffer layer limits the operating current density obviously, while the brightness and efficiency are both enhanced greatly. The highest brightness of the optimized device is achieved to be 14 000 cd/m2 at current efficiency of 3 cd/A and bias voltage of 15 V, which is about 50% higher than that of the compared device without CuOJCu buffer layer. The highest efficiency is achieved to be 5.9 cd/A at 11.6 V with 3 400 cd/m^2, which is almost twice as high as that of the compared device.展开更多
The InGaN/GaN blue light emitting diode（LED） is numerically investigated using a triangular-shaped quantum well model,which involves analysis on its energy band,carrier concentration,overlap of electron and hole wav...The InGaN/GaN blue light emitting diode（LED） is numerically investigated using a triangular-shaped quantum well model,which involves analysis on its energy band,carrier concentration,overlap of electron and hole wave functions,radiative recombination rate,and internal quantum efficiency.The simulation results reveal that the InGaN/GaN blue light emitting diode with triangular quantum wells exhibits a higher radiative recombination rate than the conventional light emitting diode with rectangular quantum wells due to the enhanced overlap of electron and hole wave functions（above 90%） under the polarization field.Consequently,the efficiency droop is only 18% in the light emitting diode with triangular-shaped quantum wells,which is three times lower than that in a conventional LED.展开更多
Native orchid species of Singapore in their natural conditions experience stress from high irradiance, high temperatures and periods of extended low rainfall, which impact orchid plant physiology and lead to reduced g...Native orchid species of Singapore in their natural conditions experience stress from high irradiance, high temperatures and periods of extended low rainfall, which impact orchid plant physiology and lead to reduced growth and productivity. In this study, it was found that there was a reduction in photochemical efficiency of photosystem II (PSII) in 6 native orchid species under high light (HL) and Bulbophyllum membranaceum under low light (LL). There was chronic photoinhibition in these 6 orchid species over a period of 3 months after transplanting onto the tree trunks without watering and fertilization, especially in Coelogynes mayeriana and Bulbophyllum membranaceum under both HL and LL. This chronic photoinhibition caused by sustained period of water deficit in their natural conditions was later reversed by natural re-watering conditions from higher rainfall. These results indicate that water deficit has a greater impact on photosynthetic light utilization efficiency than excess light. The present study also showed that after natural rewatering, relative water content (RWC) of leaves and pseudobulbs generally increased. During the natural re-watering, total leaf area also gradually increased and reached maximum expansion after 7 weeks under both HL and LL, with some exceptions due to leaf abscission or decline in total leaf area, possibly a strategy for water conservation.展开更多
We investigate the polarization-induced doping in the gradient variation of Al composition in the pAl_(0.75)Ga_(0.25)N/Al_xGa_(1-x)N hole injection layer(HIL)for deep ultraviolet light-emitting diodes(DUV-LEDs)with an...We investigate the polarization-induced doping in the gradient variation of Al composition in the pAl_(0.75)Ga_(0.25)N/Al_xGa_(1-x)N hole injection layer(HIL)for deep ultraviolet light-emitting diodes(DUV-LEDs)with an ultrathin p-GaN(4 nm)ohmic contact layer capable of emitting 277 nm.The experimental results show that the external quantum efficiency(EQE)and wall plug efficiency(WPE)of the structure graded from 0.75 to 0.55 in the HIL reach 5.49%and 5.04%,which are improved significantly by 182%and 209%,respectively,compared with the structure graded from 0.75 to 0.45,exhibiting a tremendous improvement.Both theoretical speculations and simulation results support that the larger the difference between 0.75 and x in the HIL,the higher the hole concentration that should be induced;thus,the DUV-LED has a higher internal quantum efficiency(IQE).Meanwhile,as the value of x decreases,the absorption of the DUV light emitted from the active region by the HIL is enhanced,reducing the light extraction efficiency(LEE).The IQE and LEE together affect the EQE performance of DUV-LEDs.To trade off the contradiction between the enhanced IQE and decreased LEE caused by the decrease in Al composition,the Al composition in the HIL was optimized through theoretical calculations and experiments.展开更多
The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the ca...The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the carrier(especially the hole) injection and recombination processes on the device luminescent characteristics are revealed.Without considering the device junction temperature,it is found that the device luminescent efficiency mainly depends on the hole injection efficiency at low field and the hole radiative recombination efficiency at high field respectively.The theoretical analyses are in well agreement with the experimental results.展开更多
Molybdenum trioxide （MOO3） as a cathode buffer layer is inserted between LiF and A1 to improve the efficiency of white organic light-emitting diodes （OLEDs） in this paper..By changing the MoO3 thickness, a higher ...Molybdenum trioxide （MOO3） as a cathode buffer layer is inserted between LiF and A1 to improve the efficiency of white organic light-emitting diodes （OLEDs） in this paper..By changing the MoO3 thickness, a higher current efficiency of 5.79 cd/A is obtained at a current density of 160 mA/cm2 for the device with a 0.8 nm-thick MoO3 layer as the cathode buffer layer, which is approximately two times greater than that of the device without MoO3. The mechanism for improving the device efficiency is discussed. Moreover, at a voltage of 13 V, the device with a 0.8 nm-thick MoO3 layer achieves a higher luminance of 22370 cd/m2, and the Commission Internationale de I＇Eclairage （CIE） color coordinate of the device with 1 nm-thick MoO3 layer is （0.33, 0：34）, which shows the best color purity. Simple electron-only devices are tested to confirm the impact of the MoO3 layer on the carrier injection.展开更多
It is well known that temperature acts negatively on practically all the parameters of photovoltaic solar cells. Also, the solar cells which are subjected to particularly very high temperatures are the light concentra...It is well known that temperature acts negatively on practically all the parameters of photovoltaic solar cells. Also, the solar cells which are subjected to particularly very high temperatures are the light concentration solar cells and are used in light concentration photovoltaic systems (<i><span style="font-family:Verdana;">CPV</span></i><span style="font-family:Verdana;">). In fact, the significant heating of these solar cells is due to the concentration of the solar flux which arrives on them. Light concentration solar cells appear as solar cells under strong influences of heating and temperature. It is therefore necessary to take into account temperature effect on light concentration solar cells performances in order to obtain realistic results. </span><span style="font-family:""><span style="font-family:Verdana;">This one-dimensional study of a crystalline silicon solar cell under light concentration takes into account electrons concentration gradient electric field in the determination of the continuity equation of minority carriers in the base. To determine excess minority carrier’s density, the effects of temperature on the diffusion and mobility of electrons and holes, on the intrinsic concentration of electrons, on carrier’s generation rate as well as on width of band gap have also been taken into account. The results show that an increase of temperature improves diffusion parameters and leads to an increase of the short-circuit photocurrent density. However, an increase of temperature leads to a significant decrease in open-circuit photovoltage, maximum electric power and conversion efficiency. The results also show that the operating point and the maximum power point (</span><i><span style="font-family:Verdana;">MPP</span></i><span style="font-family:Verdana;">) moves to the open circuit when the cell temperature increases.</span></span>展开更多
The efficiency of organic light-emitting devices （OLEDs） based on N,N＇-bis（1-naphthyl）-N,N＇-diphenyl-N,1＇- biphenyl-4,4＇-diamine （NPB） （the hole transport layer） and tris（8-hydroxyquinoline） aluminum （A...The efficiency of organic light-emitting devices （OLEDs） based on N,N＇-bis（1-naphthyl）-N,N＇-diphenyl-N,1＇- biphenyl-4,4＇-diamine （NPB） （the hole transport layer） and tris（8-hydroxyquinoline） aluminum （Alq3） （both emission and electron transport layers） is improved remarkably by inserting a LiF interlayer into the hole transport layer. This thin LiF interlayer can effectively influence electrical performance and significantly improve the current efficiency of the device. A device with an optimum LiF layer thickness at the optimum position in NPB exhibits a maximum current efficiency of 5.96 cd/A at 215.79 mA/cm2, which is about 86% higher than that of an ordinary device （without a LiF interlayer, 3.2 cd/A）. An explanation can be put forward that LiF in the NPB layer can block holes and balance the recombination of holes and electrons. The results may provide some valuable references for improving OLED current efficiency.展开更多
The efficiency droop behaviors of GaN-based green light-emitting diodes （LEDs） are studied as a function of temperature from 300 K to 480 K. The overall quantum efficiency of the green LEDs is found to degrade as te...The efficiency droop behaviors of GaN-based green light-emitting diodes （LEDs） are studied as a function of temperature from 300 K to 480 K. The overall quantum efficiency of the green LEDs is found to degrade as temperature increases, which is mainly caused by activation of new non-radiative recombination centers within the LED active layer. Meanwhile, the external quantum efficiency of the green LEDs starts to decrease at low injection current level （1 A/cm2 ） with a temperature-insensitive peak-efficiency-current. In contrast, the peak-efficiency-current of a control GaN-based blue LED shows continuous up-shift at higher temperatures. Around the onset point of efficiency droop, the electroluminescence spectra of the green LEDs also exhibit a monotonic blue-shift of peak energy and a reduction of full width at half maximum as injection current increases. Carrier delocalization is believed to play an important role in causing the efficiency droop in GaN-based green LEDs.展开更多
We demonstrate high current efficiency of a blue fluorescent organic light-emitting diode （OLED） by using the charge control layers （CCLs） based on Alq3 . The CCLs that are inserted into the emitting layers （EMLs...We demonstrate high current efficiency of a blue fluorescent organic light-emitting diode （OLED） by using the charge control layers （CCLs） based on Alq3 . The CCLs that are inserted into the emitting layers （EMLs） could impede the hole injection and facilitate the electron transport, which can improve the carrier balance and further expand the exciton generation region. The maximal current efficiency of the optimal device is 5.89 cd/A at 1.81 mA/cm2 , which is about 2.19 times higher than that of the control device （CD） without the CCL, and the maximal luminance is 19.660 cd/m2 at 12V. The device shows a good color stability though the green light emitting material Alq3 is introduced as the CCL in the EML, but it has a poor lifetime due to the formation of cationic Alq3 species.展开更多
We demonstrate the fabrication of hexagonal nano-pillar arrays at the surface of GaN-based light-emitting diodes （LEDs） by nanosphere lithography. By varying the oxygen plasma etching time, we could tune the size an...We demonstrate the fabrication of hexagonal nano-pillar arrays at the surface of GaN-based light-emitting diodes （LEDs） by nanosphere lithography. By varying the oxygen plasma etching time, we could tune the size and shape of the pillar. The nano-pillar has a truncated cone shape. The nano-pillar array serves as a gradual effective refractive index matcher, which reduces the reflection and increases light cone. It is found that the patterned surface absorbs more pumping light. To compare extraction efficiencies of LEDs, it is necessary to normalize the photoluminescence power spectrum with total absorption rate under fixed pumping power, then we could obtain the correct enhancement factor of the photoluminescence extraction efficiency and optimized structure. The highest enhancement factor of the extraction efficiency is 10.6.展开更多
Biomass allocation and assimilation efficiency of natural Amour linden (Tilia amurensis) samplings in different light regimes were analyzed in the paper. The results showed that shoot increment of samplings in gap was...Biomass allocation and assimilation efficiency of natural Amour linden (Tilia amurensis) samplings in different light regimes were analyzed in the paper. The results showed that shoot increment of samplings in gap was the highest and that of samplings under canopy was the least. Samplings in gap expressed apical dominance strongly but samplings in full sun and under canopy behaved intensive branching. Lateral competition or moderate shading was favored to bole construction. The patters of biomass allocation of samplings in different light environment were rather similar. The biomass translocated to stem was more than that to other organs, and about one half of photosynthate was used to support leaf turn over. On the contrary, photosynthates of samplings in full sun were mostly consumed in leaves bearing and energy balancing. The carbon assimilation for leaves of samplings in gap was the most efficient, and more carbons were fixed and translocated to non-photosynthetic organs, especially to stemwood.展开更多
基金supported by the National Natural Science Foundation of China(32172118)the National Key Research and Development Program of China(2016YFD0300110 and 2016YFD0300101)+1 种基金the Basic Scientific Research Fund of Chinese Academy of Agricultural Sciences,China(S2022ZD05)the Agricultural Science and Technology Innovation Program,China(CAAS-ZDRW202004)。
文摘The distributions of light and nitrogen within a plant's canopy reflect the growth adaptation of crops to the environment and are conducive to improving the carbon assimilation ability.So can the yield in crop production be maximized by improving the light and nitrogen distributions without adding any additional inputs?In this study,the effects of different nitrogen application rates and planting densities on the canopy light and nitrogen distributions of two highyielding maize cultivars(XY335 and DH618)and the regulatory effects of canopy physiological characteristics on radiation use efficiency(RUE)and yield were studied based on high-yield field experiments in Qitai,Xinjiang Uygur Autonomous Region,China,during 2019 and 2020.The results showed that the distribution of photosynthetically active photon flux density(PPFD)in the maize canopy decreased from top to bottom,while the vertical distribution of specific leaf nitrogen(SLN)initially increased and then decreased from top to bottom in the canopy.When SLN began to decrease,the PPDF values of XY335 and DH618 were 0.5 and 0.3,respectively,corresponding to 40.6 and49.3%of the total leaf area index(LAI).Nitrogen extinction coefficient(K_(N))/light extinction coefficient(K_(L))ratio in the middle and lower canopy of XY335(0.32)was 0.08 higher than that of DH618(0.24).The yield and RUE of XY335(17.2 t ha^(-1)and 1.8g MJ^(-1))were 7.0%(1.1 t ha^(-1))and 13.7%(0.2 g MJ^(-1))higher than those of DH618(16.1 t ha^(-1)and 1.6 g MJ^(-1)).Therefore,better light conditions(where the proportion of LAI in the upper and middle canopy was small)improved the light distribution when SLN started to decline,thus helping to mobilize the nitrogen distribution and maintain a high K_(N)and K_(N)/K_(L)ratio.In addition,K_(N)/K_(L)was a key parameter for yield improvement when the maize nutrient requirements were met at 360 kg N ha^(-1).At this level,an appropriately optimized high planting density could promote nitrogen utilization and produce higher yields and greater efficiency.The results of this study will be important for achieving high maize yields and the high efficiency cultivation and breeding of maize in the future.
基金financially supported by the National Natural Science Foundation of China(21905137)the Research Grants Council of Hong Kong(15307922,C5037-18G,C4005-22Y)+1 种基金RGC Senior Research Fellowship Scheme(SRFS2223-5S01)the Hong Kong Polytechnic University:Sir Sze-yuen Chung Endowed Professorship Fund(8-8480)。
文摘Semitransparent organic photovoltaics(ST-OPVs)for building integration represent a pivotal direction in the development of photovoltaic industry.Solution-processed silver nanowires(AgNWs)are considered promising candidates for transparent electrodes in semitransparent devices due to their high transparency-conductivity-efficiency merit,large-scale processability,and low cost.In this work,we develop two solution-processed organic–inorganic hybrid electrodes,named AgNWs-PD and AgNWsPC,utilizing AgNWs as the conductive framework and aliphatic amine-functionalized perylene-diimide(PDINN)as the sandwiched material,while AgNWs-PC exhibits significantly improved electrical conductivity and enhanced contact area with the underlying electron transport layer.The optimized device achieves a power conversion efficiency of 9.45%with an open circuit voltage of 0.846 V,a high filling factor of 75.4%,and an average visible transmittance(AVT)of 44.0%,delivering an outstanding light utilization efficiency(LUE)of 4.16%,which is the highest reported value for all solution-processed ST-OPVs.In addition,by coupling a 30-nm tellurium dioxide atop AgNWs-PC,the bifaciality factor of derivative devices improves from 73.7%to 99.4%,while maintaining a high bifacial LUE over 3.7%.Our results emphasize the superiority and effectiveness of PDINN-sandwiched AgNWs electrodes for highperformance and all solution-processed ST-OPVs.
基金Under the auspices of the National Key Research and Development Program of China(No.2019YFA0606603)。
文摘Gross primary production(GPP)is a crucial indicator representing the absorption of atmospheric CO_(2) by vegetation.At present,the estimation of GPP by remote sensing is mainly based on leaf-related vegetation indexes and leaf-related biophysical para-meter leaf area index(LAI),which are not completely synchronized in seasonality with GPP.In this study,we proposed chlorophyll content-based light use efficiency model(CC-LUE)to improve GPP estimates,as chlorophyll is the direct site of photosynthesis,and only the light absorbed by chlorophyll is used in the photosynthetic process.The CC-LUE model is constructed by establishing a linear correlation between satellite-derived canopy chlorophyll content(Chlcanopy)and FPAR.This method was calibrated and validated utiliz-ing 7-d averaged in-situ GPP data from 14 eddy covariance flux towers covering deciduous broadleaf forest ecosystems across five dif-ferent climate zones.Results showed a relatively robust seasonal consistency between Chlcanopy with GPP in deciduous broadleaf forests under different climatic conditions.The CC-LUE model explained 88% of the in-situ GPP seasonality for all validation site-year and 56.0% of in-situ GPP variations through the growing season,outperforming the three widely used LUE models(MODIS-GPP algorithm,Vegetation Photosynthesis Model(VPM),and the eddy covariance-light use efficiency model(EC-LUE)).Additionally,the CC-LUE model(RMSE=0.50 g C/(m^(2)·d))significantly improved the underestimation of GPP during the growing season in semi-arid region,re-markably decreasing the root mean square error of averaged growing season GPP simulation and in-situ GPP by 75.4%,73.4%,and 37.5%,compared with MOD17(RMSE=2.03 g C/(m^(2)·d)),VPM(RMSE=1.88 g C/(m^(2)·d)),and EC-LUE(RMSE=0.80 g C/(m^(2)·d))model.The chlorophyll-based method proved superior in capturing the seasonal variations of GPP in forest ecosystems,thereby provid-ing the possibility of a more precise depiction of forest seasonal carbon uptake.
文摘Glass substrates which realize high out-coupling efficiency OLEDs （organic light emitting diodes） were developed. A scattering layer whose matrix was made of high refractive index glass was formed on a glass substrate, and pores in the glass matrix work as scattering centers. The out-coupling efficiency of an OLED using this substrate is 1.8 times higher compared with an OLED using an untreated glass substrate. Furthermore angular dependency of the color and color variation between panels can be successfully suppressed.
基金funded by the Geran Universiti Penyelidikan(GUP),under the grant number GUP-2022-011 funded by the Universiti Kebangsaan Malaysia。
文摘This study presents a detailed comparative analysis of three electron transport layer(ETL)materials for perovskite solar cells(PSCs),namely titanium dioxide(TiO_(2)),barium titanate(BaTiO_(3)or BTO),and strontium-doped barium titan-ate(Ba_(1−x)Sr_(x)TiO_(3)or BST),and their impact on the quantum efficiency(QE)and power conversion efficiency(PCE)of CH_(3)NH_(3)PbI_(3)(MAPbI_(3))PSCs.The optimized structure demonstrates that devices utilizing BST as an ETL achieved the highest PCE of 29.85%,exhibiting superior thermal stability with the lowest temperature coefficient of−0.43%/K.This temperature-induced degradation is comparable to that of commercially available silicon cells.Furthermore,BST-based ETLs show 29.50%and 26.48%higher PCE than those of TiO_(2)-based and BTO-based ETLs.The enhanced internal QE and favorable current density–voltage(J–V)characteristics of BST compared with those of TiO_(2)and BTO are attributed to its improved charge carrier separation,reduced recombination rates,and robust electrical characteristics under varied environmental conditions.Furthermore,the electric field and generation rate of the BST-based ETLs show a more favorable distribution than those of the TiO_(2)-based and BTO-based ETLs.These findings provide significant insights into the role of different ETLs in enhancing QE,indicating that BST is a superior ETL that enhances both the efficiency and stability of PSCs.This study contributes to the understanding of how perovskite-structured ETLs can be used to design and optimize highly efficient and stable photovoltaic devices.
基金supported by the National Key Research and Development Program(MOST,No.2022YFE0108800)the National Natural Science Foundation of China(Nos.52272165,U2005213 and 52172157)the Major Science and Technology Projects of Xiamen Science and Technology Bureau(No.3502Z20231018).
文摘Solid-state lighting is now developing toward high-power and super-brightness,but is largely limited by the lack of highly robust and efficient color conversion materials that can be survived from high-power or high-power density excitation,typically the red-emitting ones.In this work,we fabricated highly effi-cient and pore-free Sr_(0.5)Ca_(0.5)AlSiN_(3)∶Eu^(2+)(SCASN)red-emitting ceramics by spark plasma sintering of fine phosphor powders.These fine phosphor powders were prepared by treating the commercial phosphors with high-energy ball-milling,centrifugation and acid washing,leading to a particle size of 2.55μm and an internal quantum efficiency as high as 74.0%under 450 nm excitation.The phosphor powders can be densified into SCASN ceramics without using sintering additives at a temperature as low as 1475℃,and the ceramics show an internal quantum efficiency of 75.3%,which is 50%higher than those ceram-ics fabricated with untreated commercial powders.When excited by a high-power blue LED at a current density of 4 A/mm^(2),the SCASN ceramics have a maximum luminous flux of 660 lm(i.e.,26 Mcd/m^(2)).The phosphor ceramics can also withstand a high laser power density of 15.7 W/mm^(2),and exhibit an output luminance of 188 Mcd/m^(2).This work provides a general method to prepare fine phosphor powders that enable to fabricate high efficiency phosphor ceramics used in high-power solid-state lighting.
基金the National Basic Research Program of China(Grant No.2009CB623604)the National Natural Science Foundation of China(Grant Nos.61204087,51173049,U0634003,61036007,and 60937001)+1 种基金the Fundamental Research Funds for the Central Universities,China(Grant Nos.2011ZB0002 and 2011ZM0009)China Postdoctoral Science Foundation
文摘High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）： tetrafluoro-tetracyanoqino dimethane （F4-TCNQ）/N,N-di（naphthalene-1-yl）-N,N-diphenyl-benzidine （NPB）/ 4,4-N,N-dicarbazolebiphenyl （CBP）： iridium （III） diazine complexes （MPPZ） 2 Ir（acac）/NPB/2-methyl-9,10-di（2-naphthyl）anthracene （MADN）： p-bis（p-N,N-di-phenyl-aminostyryl）benzene （DSA-ph）/bis（10-hydroxybenzo[h] quino-linato）beryllium complex （Bebq2）/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l’Eclairage （CIE） chromaticity coordinates are almost constant during a large voltage change of 6–12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.
基金Project supported by the National High Technology Research and Development Program of China(Grant No.2006AA03A121)the National Basic Research Program of China(Grant No.2006CB604900)
文摘The reasons for low output power of AlGalnP Light Emitting Diodes （LEDs） have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especially at a large injected current which would reduce both the internal and external quantum efficiencies. Two kinds of LEDs with the same active region but different window layers have been fabricated. The new window layer composed of textured 0.5 μm GaP and thin Indium-Tin-Oxide film has shown that low external quantum efficiency （EQE） has serious impaction on the internal quantum efficiency （IQE）, because the carrier distribution will change with the body temperature increasing due to the heat inside, and the test results have shown the evidence of LEDs with lower output power and bigger wavelength red shift.
基金supported by the National Natural Science Foundation of China(No.61274063)
文摘An organic light-emitting diode （OLED） device with high efficiency and brightness is fabricated by inserting CuOJCu dual inorganic buffer layers between indium-tin-oxide （ITO） and hole-transport layer （HTL）. The CuOx/Cu buffer layer limits the operating current density obviously, while the brightness and efficiency are both enhanced greatly. The highest brightness of the optimized device is achieved to be 14 000 cd/m2 at current efficiency of 3 cd/A and bias voltage of 15 V, which is about 50% higher than that of the compared device without CuOJCu buffer layer. The highest efficiency is achieved to be 5.9 cd/A at 11.6 V with 3 400 cd/m^2, which is almost twice as high as that of the compared device.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61076013,51102003,and 60990313)the National Basic Research Program of China (Grant No. 2012CB619304)the Specialized Research Fund for the Doctoral Program of Higher Education,China (Grant No. 20100001120014)
文摘The InGaN/GaN blue light emitting diode（LED） is numerically investigated using a triangular-shaped quantum well model,which involves analysis on its energy band,carrier concentration,overlap of electron and hole wave functions,radiative recombination rate,and internal quantum efficiency.The simulation results reveal that the InGaN/GaN blue light emitting diode with triangular quantum wells exhibits a higher radiative recombination rate than the conventional light emitting diode with rectangular quantum wells due to the enhanced overlap of electron and hole wave functions（above 90%） under the polarization field.Consequently,the efficiency droop is only 18% in the light emitting diode with triangular-shaped quantum wells,which is three times lower than that in a conventional LED.
文摘Native orchid species of Singapore in their natural conditions experience stress from high irradiance, high temperatures and periods of extended low rainfall, which impact orchid plant physiology and lead to reduced growth and productivity. In this study, it was found that there was a reduction in photochemical efficiency of photosystem II (PSII) in 6 native orchid species under high light (HL) and Bulbophyllum membranaceum under low light (LL). There was chronic photoinhibition in these 6 orchid species over a period of 3 months after transplanting onto the tree trunks without watering and fertilization, especially in Coelogynes mayeriana and Bulbophyllum membranaceum under both HL and LL. This chronic photoinhibition caused by sustained period of water deficit in their natural conditions was later reversed by natural re-watering conditions from higher rainfall. These results indicate that water deficit has a greater impact on photosynthetic light utilization efficiency than excess light. The present study also showed that after natural rewatering, relative water content (RWC) of leaves and pseudobulbs generally increased. During the natural re-watering, total leaf area also gradually increased and reached maximum expansion after 7 weeks under both HL and LL, with some exceptions due to leaf abscission or decline in total leaf area, possibly a strategy for water conservation.
基金the National Natural Science Foundation of China(Grant No.62104085)the Innovation/Entrepreneurship Program of Jiangsu Province,China(Grant No.JSSCTD202146)。
文摘We investigate the polarization-induced doping in the gradient variation of Al composition in the pAl_(0.75)Ga_(0.25)N/Al_xGa_(1-x)N hole injection layer(HIL)for deep ultraviolet light-emitting diodes(DUV-LEDs)with an ultrathin p-GaN(4 nm)ohmic contact layer capable of emitting 277 nm.The experimental results show that the external quantum efficiency(EQE)and wall plug efficiency(WPE)of the structure graded from 0.75 to 0.55 in the HIL reach 5.49%and 5.04%,which are improved significantly by 182%and 209%,respectively,compared with the structure graded from 0.75 to 0.45,exhibiting a tremendous improvement.Both theoretical speculations and simulation results support that the larger the difference between 0.75 and x in the HIL,the higher the hole concentration that should be induced;thus,the DUV-LED has a higher internal quantum efficiency(IQE).Meanwhile,as the value of x decreases,the absorption of the DUV light emitted from the active region by the HIL is enhanced,reducing the light extraction efficiency(LEE).The IQE and LEE together affect the EQE performance of DUV-LEDs.To trade off the contradiction between the enhanced IQE and decreased LEE caused by the decrease in Al composition,the Al composition in the HIL was optimized through theoretical calculations and experiments.
文摘The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the carrier(especially the hole) injection and recombination processes on the device luminescent characteristics are revealed.Without considering the device junction temperature,it is found that the device luminescent efficiency mainly depends on the hole injection efficiency at low field and the hole radiative recombination efficiency at high field respectively.The theoretical analyses are in well agreement with the experimental results.
基金supported by the National Natural Science Foundation of China(No.61076066)the Doctor Foundation of Shaanxi University of Scienceand Technology(No.BJ09-07)
文摘Molybdenum trioxide （MOO3） as a cathode buffer layer is inserted between LiF and A1 to improve the efficiency of white organic light-emitting diodes （OLEDs） in this paper..By changing the MoO3 thickness, a higher current efficiency of 5.79 cd/A is obtained at a current density of 160 mA/cm2 for the device with a 0.8 nm-thick MoO3 layer as the cathode buffer layer, which is approximately two times greater than that of the device without MoO3. The mechanism for improving the device efficiency is discussed. Moreover, at a voltage of 13 V, the device with a 0.8 nm-thick MoO3 layer achieves a higher luminance of 22370 cd/m2, and the Commission Internationale de I＇Eclairage （CIE） color coordinate of the device with 1 nm-thick MoO3 layer is （0.33, 0：34）, which shows the best color purity. Simple electron-only devices are tested to confirm the impact of the MoO3 layer on the carrier injection.
文摘It is well known that temperature acts negatively on practically all the parameters of photovoltaic solar cells. Also, the solar cells which are subjected to particularly very high temperatures are the light concentration solar cells and are used in light concentration photovoltaic systems (<i><span style="font-family:Verdana;">CPV</span></i><span style="font-family:Verdana;">). In fact, the significant heating of these solar cells is due to the concentration of the solar flux which arrives on them. Light concentration solar cells appear as solar cells under strong influences of heating and temperature. It is therefore necessary to take into account temperature effect on light concentration solar cells performances in order to obtain realistic results. </span><span style="font-family:""><span style="font-family:Verdana;">This one-dimensional study of a crystalline silicon solar cell under light concentration takes into account electrons concentration gradient electric field in the determination of the continuity equation of minority carriers in the base. To determine excess minority carrier’s density, the effects of temperature on the diffusion and mobility of electrons and holes, on the intrinsic concentration of electrons, on carrier’s generation rate as well as on width of band gap have also been taken into account. The results show that an increase of temperature improves diffusion parameters and leads to an increase of the short-circuit photocurrent density. However, an increase of temperature leads to a significant decrease in open-circuit photovoltage, maximum electric power and conversion efficiency. The results also show that the operating point and the maximum power point (</span><i><span style="font-family:Verdana;">MPP</span></i><span style="font-family:Verdana;">) moves to the open circuit when the cell temperature increases.</span></span>
基金supported by the National Natural Science Foundation of China (Grant Nos. 60906022 and 60876046)the Tianjin Natural Science Foundation of China (Grant No. 10JCYBJC01100)
文摘The efficiency of organic light-emitting devices （OLEDs） based on N,N＇-bis（1-naphthyl）-N,N＇-diphenyl-N,1＇- biphenyl-4,4＇-diamine （NPB） （the hole transport layer） and tris（8-hydroxyquinoline） aluminum （Alq3） （both emission and electron transport layers） is improved remarkably by inserting a LiF interlayer into the hole transport layer. This thin LiF interlayer can effectively influence electrical performance and significantly improve the current efficiency of the device. A device with an optimum LiF layer thickness at the optimum position in NPB exhibits a maximum current efficiency of 5.96 cd/A at 215.79 mA/cm2, which is about 86% higher than that of an ordinary device （without a LiF interlayer, 3.2 cd/A）. An explanation can be put forward that LiF in the NPB layer can block holes and balance the recombination of holes and electrons. The results may provide some valuable references for improving OLED current efficiency.
基金Project supported by the State Key Program for Basic Research of China (Grant Nos. 2010CB327504, 2011CB301900, and 2011CB922100)the National Natural Science Foundation of China (Grant Nos. 60825401, 60936004, and 11104130)the Natural Science Foundation of Jiangsu Province, China (Grant Nos. BK2012110, BK2011556, and BK2011050)
文摘The efficiency droop behaviors of GaN-based green light-emitting diodes （LEDs） are studied as a function of temperature from 300 K to 480 K. The overall quantum efficiency of the green LEDs is found to degrade as temperature increases, which is mainly caused by activation of new non-radiative recombination centers within the LED active layer. Meanwhile, the external quantum efficiency of the green LEDs starts to decrease at low injection current level （1 A/cm2 ） with a temperature-insensitive peak-efficiency-current. In contrast, the peak-efficiency-current of a control GaN-based blue LED shows continuous up-shift at higher temperatures. Around the onset point of efficiency droop, the electroluminescence spectra of the green LEDs also exhibit a monotonic blue-shift of peak energy and a reduction of full width at half maximum as injection current increases. Carrier delocalization is believed to play an important role in causing the efficiency droop in GaN-based green LEDs.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 60906022 and 60676051)the Natural Science Foundation of Tianjin,China (Grant No. 10JCYBJC01100)+2 种基金the Scientific Developing Foundation of Tianjin Education Commission, China (Grant No. 2011ZD02)the Jiangsu Provincial Natural Science Development Foundation for University, China (Grant No. 09KJB140006)the Tianjin Natural Science Council (Grant No. 10SYSYJC28100)
文摘We demonstrate high current efficiency of a blue fluorescent organic light-emitting diode （OLED） by using the charge control layers （CCLs） based on Alq3 . The CCLs that are inserted into the emitting layers （EMLs） could impede the hole injection and facilitate the electron transport, which can improve the carrier balance and further expand the exciton generation region. The maximal current efficiency of the optimal device is 5.89 cd/A at 1.81 mA/cm2 , which is about 2.19 times higher than that of the control device （CD） without the CCL, and the maximal luminance is 19.660 cd/m2 at 12V. The device shows a good color stability though the green light emitting material Alq3 is introduced as the CCL in the EML, but it has a poor lifetime due to the formation of cationic Alq3 species.
基金Project supported by the the National Natural Science Foundation of China (Grant Nos. 10774195, U0834001, 10974263, 11174374, and 10725420)the KeyProgram of Ministry of Education, China (Grant No. 309024)the New Century Excellent Talents in University, and the National Basic Research Program of China (Grant No. 2010CB923200)
文摘We demonstrate the fabrication of hexagonal nano-pillar arrays at the surface of GaN-based light-emitting diodes （LEDs） by nanosphere lithography. By varying the oxygen plasma etching time, we could tune the size and shape of the pillar. The nano-pillar has a truncated cone shape. The nano-pillar array serves as a gradual effective refractive index matcher, which reduces the reflection and increases light cone. It is found that the patterned surface absorbs more pumping light. To compare extraction efficiencies of LEDs, it is necessary to normalize the photoluminescence power spectrum with total absorption rate under fixed pumping power, then we could obtain the correct enhancement factor of the photoluminescence extraction efficiency and optimized structure. The highest enhancement factor of the extraction efficiency is 10.6.
文摘Biomass allocation and assimilation efficiency of natural Amour linden (Tilia amurensis) samplings in different light regimes were analyzed in the paper. The results showed that shoot increment of samplings in gap was the highest and that of samplings under canopy was the least. Samplings in gap expressed apical dominance strongly but samplings in full sun and under canopy behaved intensive branching. Lateral competition or moderate shading was favored to bole construction. The patters of biomass allocation of samplings in different light environment were rather similar. The biomass translocated to stem was more than that to other organs, and about one half of photosynthate was used to support leaf turn over. On the contrary, photosynthates of samplings in full sun were mostly consumed in leaves bearing and energy balancing. The carbon assimilation for leaves of samplings in gap was the most efficient, and more carbons were fixed and translocated to non-photosynthetic organs, especially to stemwood.
