Tibetan heritage buildings have a high historical and cultural value. They have endured adverse environmental loadings over hundreds of years without significant damage. However, there are few reports on their structu...Tibetan heritage buildings have a high historical and cultural value. They have endured adverse environmental loadings over hundreds of years without significant damage. However, there are few reports on their structural characteristics under normal environmental loadings and their behavior under dynamic loadings. In this research, a typical Tibetan wooden wall-frame building is selected to study its dynamic characteristics. Field measurements of the structure were conducted under environmental excitation to collect acceleration responses. The stochastic subspace identification （SSI） method was adopted to calculate the structural modal parameters and obtain the out-of-plane vibration characteristics of the slab and frames. The results indicated that the wall-frame structure had a lower out-of-plane stiffness and greater in-plane stiffness due to the presence of stone walls. Due to poor identified damping ratio estimates from the SSI method, a method based on the variance upper bound was proposed to complement the existing variance lower bound method for estimating the modal damping ratio to address the significant damping variability obtained from different points and measurements. The feasibility of the proposed method was illustrated with the measured data from the floor slab of the structure. The variance lower and upper bound methods both provided consistent results compared to those from the traditional SSI method.展开更多
Rigid blocking masses are located in the typical base structure of a power cabin based on the impedance mismatch principle.By combining the acoustic-structural coupling method and statistical energy analysis,the full-...Rigid blocking masses are located in the typical base structure of a power cabin based on the impedance mismatch principle.By combining the acoustic-structural coupling method and statistical energy analysis,the full-band vibration and sound radiation reduction effect of vibration isolation masses located in a base structure was researched.The influence of the blocking mass’ cross-section size and shape parameters and the layout location of the base isolation performance was discussed.Furthermore,the effectiveness of rigid vibration isolation design of the base structure was validated.The results show that the medium and high frequency vibration and sound radiation of a power cabin are effectively reduced by a blocking mass.Concerning weight increment and section requirement,suitably increasing the blocking mass size and section height and reducing section width can result in an efficiency-cost ratio.展开更多
The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more...The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more precise lattice parameters using the interaction points for the pseudo-Kossel pattern obtained from laser-induced X-ray diffraction(XRD).This method has been validated by the analysis of an XRD experiment conducted on iron single crystals.Furthermore,the method was used to calculate the compression ratio and rotated angle of an LiF sample under high pressure loading.This technique provides a robust tool for in-situ characterization of structural changes in single crystals under extreme conditions.It has significant implications for studying the equation of state and phase transitions.展开更多
Optimization of structural parameters aimed at improving the load carrying capacity of spatial flexible redundant manipulators is presented in this paper. In order to increase the ratio of load to mass of robots, the ...Optimization of structural parameters aimed at improving the load carrying capacity of spatial flexible redundant manipulators is presented in this paper. In order to increase the ratio of load to mass of robots, the cross-sectional parameters and constructional parameters are optimized respectively. The cross-sectional and configurational parameters are optimized simultaneously. The numerical simulation of a 4R spatial manipulator is performed. The results show that the load capacity of robots has been greatly improved through the optimization strategies proposed in this paper.展开更多
[Objective] This paper was to study effects of pelleted total mixed ration with different concentrate-roughage ratios on production performance and serum biochemical parameters of fattening Hainan black goats.[Method]...[Objective] This paper was to study effects of pelleted total mixed ration with different concentrate-roughage ratios on production performance and serum biochemical parameters of fattening Hainan black goats.[Method] Thirty-six fattening Hainan black goats with the same genetic background and similar initial weight of(14.08±0.13) kg were randomly assigned into three treatments. Goats were fed with Juncao + concentrate(control group), pelleted total mixed ration I(concentrate: roughage 50 ∶50, group Ⅰ) and Ⅱ(concentrate: roughage 45∶55, group Ⅱ), respectively. The test lasted 45 d.[Result] The final weight, daily gain and feed intake of rams in experimental group Ⅰ were significantly higher than those of control group and experimental group Ⅱ(P<0.05);the final weight and daily gain of rams in experimental group Ⅰ were also markedly higher than those of experimental group Ⅱ(P<0.05);the feed/gain of rams in experimental group Ⅰ was significantly lower than those in control group and experimental group Ⅱ(P<0.05). The feed gain cost of rams in experimental group Ⅰ was markedly lower than that in experimental group Ⅱ( P<0.05), but was significantly higher than that in experimental group Ⅰ(P<0.05);the gross profit of rams in experimental group Ⅰ was significantly higher than those in control group and experimental group Ⅱ(P<0.05). Compared with control group and experimental group Ⅱ, the serum total protein and glucose lev-els in experimental group Ⅱ increased significantly(P<0.05), but the urea nitrogen content reduced(P>0.05).[Conclusion] When the concentrateroughage ratio of pelleted total mixed ration was 50∶50, the fattening effect of Hainan black goat was better, and the serum total protein and glucose levels were evidently improved.展开更多
In this paper conventional stochastic resonance （CSR） is realized by adding the noise intensity. This demonstrates that tuning the system parameters with fixed noise can make the noise play a constructive role and r...In this paper conventional stochastic resonance （CSR） is realized by adding the noise intensity. This demonstrates that tuning the system parameters with fixed noise can make the noise play a constructive role and realize parameter- induced stochastic resonance （PSR）. PSR can be interpreted as changing the intrinsic characteristic of the dynamical system to yield the cooperative effect between the stochastic-subjected nonlinear system and the external periodic force. This can be realized at any noise intensity, which greatly differs from CSR that is realized under the condition of the initial noise intensity not greater than the resonance level. Moreover, it is proved that PSR is different from the optimization of system parameters.展开更多
To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different cast...To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different casting parameters such as pouring temperature, inoculation, carbon equivalent, moisture content, green compression strength, permeability and mould hardness were selected. Three different melts of metal with 0.4wt.%, 0.6wt.%, and 0.8wt.% inoculation （Fe-Si-Mg alloy and post inoculant） were produced using a 1-ton capacity coreless medium frequency induction furnace. L-27 orthogonal array with 3-level settings were chosen for the analysis. Responses for each run were observed. The signal-to-noise （S/N） ratio for each run was calculated using the Taguchi approach, and the optimized levels of different casting parameters were identified based on the SIN ratio. The analysis of variance for the casting acceptance percentage concludes that inoculation is the most significant factor affecting the castings＇ quality with a contribution percentage of 44%; an increase in inoculation results in a significant improvement in acceptance percentage of ductile iron castings. The experiment results showed that with the optimized parameters, the rejection rate was reduced from 16.98% to 6.07%.展开更多
Following the parameterization of sheared entrainment obtained in the companion paper, Liu et al. （2016）, the present study aims to further investigate the characteristics of entrainment, and develop a simple model ...Following the parameterization of sheared entrainment obtained in the companion paper, Liu et al. （2016）, the present study aims to further investigate the characteristics of entrainment, and develop a simple model for predicting the growth rate of a well-developed and sheared CBL. The relative stratification, defined as the ratio of the stratification in the free atmosphere to that in the entrainment zone, is found to be a function of entrainment flux ratio （Ae）. This leads to a simple expression of the entrainment rate, in which Ae needs to be parameterized. According to the results in Liu et al. （2016）, Ae can be simply expressed as the ratio of the convective velocity scale in the sheared CBL to that in the shear-free CBL. The parameterization of the convective velocity scale in the sheared CBL is obtained by analytically solving the bulk model with several assumptions and approximations. Results indicate that the entrainment process is influenced by the dynamic effect, the interaction between mean shear and environmental stratification, and one other term that includes the Coriolis effect. These three parameterizations constitute a simple model for predicting the growth rate of a well-developed and sheared CBL. This model is validated by outputs of LESs, and the results show that it performs satisfactorily. Compared with bulk models, this model does not need to solve a set of equations for the CBL. It is more convenient to apply in numerical models.展开更多
Hypothesis testing analysis and unknown parameter estimation of both the intermediate frequency(IF) and baseband GPS signal detection are given by using the generalized likelihood ratio test(GLRT) approach,applying th...Hypothesis testing analysis and unknown parameter estimation of both the intermediate frequency(IF) and baseband GPS signal detection are given by using the generalized likelihood ratio test(GLRT) approach,applying the model of GPS signal in white Gaussian noise,It is proved that the test statistic follows central or noncentral F distribution,It is also pointed out that the test statistic is nearly identical to central or noncentral chi-squared distribution because the processing samples are large enough to be considered as infinite in GPS acquisition problem.It is also proved that the probability of false alarm,the probability of detection and the threshold are affected largely when the hypothesis testing refers to the full pseudorandom noise(PRN) code phase and Doppler frequency search space cells instead of each individual cell.The performance of the test statistic is also given with combining the noncoherent integration.展开更多
A water rocket is a rocket system that obtains thrust by injecting water with compressed air of up to about 8 atmospheres. It is usually manufactured using a pressure-resistant PET bottle. The mechanical elements and ...A water rocket is a rocket system that obtains thrust by injecting water with compressed air of up to about 8 atmospheres. It is usually manufactured using a pressure-resistant PET bottle. The mechanical elements and principles contained in the water rocket have much in common with the actual small rocket system, and are suitable as educational and research teaching materials in the field of mechanics. Especially in the field of disaster prevention and mitigation, the use of water rockets is being researched and developed as a rescue tool in the event of a flood or earthquake as a disaster countermeasure. However, since the water rocket is a flying object based on the mechanical principle, it is important to ensure the accuracy and stability of the flight path. In this paper, a mechanical simulator is developed with a numerical calculation program based on the mechanical consideration of water rocket flight performance. In addition, the correlation between the flight distance obtained in the simulation and the estimated flight distance is analyzed by applying a multivariate analysis method and verifying the validity of the flight distance calculated from the result. Based on the verification results, we will apply a statistical optimization method to approach the optimization of flight stability performance conditions for water rockets.展开更多
Conventional parameter estimation methods for pseudo-random binary code-linear frequency modulation(PRBC-LFM)signals require prior knowledge,are computationally complex,and exhibit poor performance at low signal-to-no...Conventional parameter estimation methods for pseudo-random binary code-linear frequency modulation(PRBC-LFM)signals require prior knowledge,are computationally complex,and exhibit poor performance at low signal-to-noise ratios(SNRs).To overcome these problems,a blind parameter estimation method based on a Duffing oscillator array is proposed.A new relationship formula among the state of the Duffing oscillator,the pseudo-random sequence of the PRBC-LFM signal,and the frequency difference between the PRBC-LFM signal and the periodic driving force signal of the Duffing oscillator is derived,providing the theoretical basis for blind parameter estimation.Methods based on amplitude method,short-time Fourier transform method,and power spectrum entropy method are used to binarize the output of the Duffing oscillator array,and their performance is compared.The pseudo-random sequence is estimated using Duffing oscillator array synchronization,and the carrier frequency parameters are obtained by the relational expressions and characteristics of the difference frequency.Simulation results show that this blind estimation method overcomes limitations in prior knowledge and maintains good parameter estimation performance up to an SNR of-35 dB.展开更多
The spatial distribution of physico-chemical parameters（sea surface temperature（SST）, p H, sea surface salinity（SSS）, dissolved oxygen（DO） and Secchi depth） along with filterable nutrients（dissolved inorganic...The spatial distribution of physico-chemical parameters（sea surface temperature（SST）, p H, sea surface salinity（SSS）, dissolved oxygen（DO） and Secchi depth） along with filterable nutrients（dissolved inorganic nitrate（DIN）,dissolved inorganic phosphate（DIP） and reactive silicate（DSi）） are measured in the winter months of November,December, January and February for four consecutive years from 2009–2010 to 2012–2013 on the shallow continental shelf（〈20 m bathymetry） of the coastal waters（up to 18 km away from shoreline） of the northern Bay of Bengal（n Bo B） during the highest high tide（HHT） and lowest low tide（LLT） hours for the first time. The variability of the coastal biogeochemical environment is assessed during the HHT and LLT hours and for this purpose, seawater samples are collected from seven different locations of a transect in the coastal region. Physicochemical parameters（except SST） show significant difference in magnitude during the HHT and LLT hours respectively. p H, SSS and DO are found to increase in the HHT hours and vice-versa. The data reveal that during the LLT hours, a relative increase of freshwater input in the n Bo B can have elevated the nutrient concentration compared with that observed during the HHT hours. The ratio of nutrient concentration is found to deviate significantly from the Redfield ratio. The abundance of DIP is much higher compared with that of DIN and DSi.The anthropogenic sources of DIP from the upstream flow（especially the domestic effluent of several metropolises） can be mainly attributed behind such an observation. In order to characterize and establish the trend of such variation in such an important bio-climatic region, long-term and systematic ecosystem monitoring in the coastal water of the n Bo B northern Bay of Bengal should be carried out throughout the year.展开更多
A method of obtaining the large strain consolidation parameters of dredged clays considering the influence of the initial water content is investigated in this study. According to the test results of remolded clays wi...A method of obtaining the large strain consolidation parameters of dredged clays considering the influence of the initial water content is investigated in this study. According to the test results of remolded clays with high initial water contents reported by Hong et al. （2010）, a relationship between the void ratio （e） and effective stress （a3 is established. Furthermore, based on the available permeability data from the literature, a new relationship between the permeability coefficient （k） and the ratio （e/eL） of the void ratio to the void ratio at the liquid limit （eL） is proposed. The new proposed expression considering the initial water content improves the e-k equation established by Nagaraj et al. （1994）. Finally, the influence of the initial void ratio and effective stress on the large strain consolidation coefficient g（e） defined by Gibson et al. （1981） and k/（1 ＋e） in large strain analysis is discussed. The results show that, under a constant effective stress, the value of k/（1 ＋e） increases with the initial void ratio. The large strain consolidation coefficient shows the law of segmentation change, which decreases with the increase of the effective stress when the effective stress is less than the remolded yield stress, but increases rapidly with the effective stress when the effective stress is larger than the remolded yield stress.展开更多
To adapt to the change of aquaculture workshop site,optimize the shape of aquaculture tanks and improve the utilization rate of breeding space,it is necessary to determine the appropriate length width ratio parameters...To adapt to the change of aquaculture workshop site,optimize the shape of aquaculture tanks and improve the utilization rate of breeding space,it is necessary to determine the appropriate length width ratio parameters of aquaculture tanks.In this paper,computational fluid dynamics(CFD)technology is adopted to study the flow field performance of aquaculture tanks with different L/B ratios(L:the length;B:the width,of aquaculture tank)and different jet direction conditions(lengthways jet and widthways jet).A three-dimensional numerical calculation model of turbulence in rounded rectangle aquaculture tanks in dual-diagonal-inlet layout was established.Jet directions are arranged lengthways and widthways,and the water flow velocity,resistance coefficient change,vorticity,etc.are analyzed under two working conditions.Results show that the flow field performance in aquaculture tank decreases with the increase of the L/B ratio.The flow field performed well when L/B was 1.0-1.3,sharply dropped at 1.4-1.6,and poor at 1.7-1.9.The results provided a theoretical basis for the design and optimization in flow field performance of the industrialized circulating aquaculture tanks.展开更多
The main targets of seismic exploration research in Leijia carbonatite tight sandstone oil area of Liaohe depression are thin reservoirs prediction and minor faults identification, which is one of the important repres...The main targets of seismic exploration research in Leijia carbonatite tight sandstone oil area of Liaohe depression are thin reservoirs prediction and minor faults identification, which is one of the important representatives of complex exploration objects in Liaohe depression. High precision 3D seismic exploration has significantly improved the ability of thin reservoirs prediction and minor faults identification of this area. Reducing the cost of high precision 3D seismic exploration through optimizing the acquisition parameters is very important for the next step exploration and development of Liaohe depression and similar areas. Based on high precision 3D seismic acquisition data in Leijia tight sandstone oil area, multiple sub-geometries are obtained with different bin sizes, different folds, different aspect ratio, different line intervals by extracting receiver points and shot points, and PSTM processing is performed respectively, obtained PSTM datasets of the sub-geometries, extract time slices, amplitude slices along the layer, coherent slices and so on. We evaluate the data results of the sub-geometries from the aspects of signal-to-noise ratio, thin reservoirs resolution, acquisition footprint and so on. Considering the exploration cost and data effect of each sub-geometry, the optimal direction of the main parameters of high precision seismic exploration in Liaohe depression is put forward, and the acquisition effect of adjacent area by the optimized parameters is given.展开更多
In this paper, the parameter estimation problem is investigated for the continuous time stochastic logistic diffusion system. A new continuous process is built based on the likelihood ratio scheme, the Radon-Nikodym d...In this paper, the parameter estimation problem is investigated for the continuous time stochastic logistic diffusion system. A new continuous process is built based on the likelihood ratio scheme, the Radon-Nikodym derivative and the explicit expressions of the error of estimation are given under this new continuous process. By using the random time transformations, law of large numbers for martingales, law of iterated logarithm and stationary distribution of solution, the consistency property are proved for the estimation error. Finally, a numerical simulation is presented to demonstrate the effectiveness of the proposed method in this paper.展开更多
A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and back...A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and backwashing. The design and operation parameters, which affect the performance of the filter, are discussed. The key design parameters are provided as follows: diameter of filter material is 0.7 to 1.0 mm, depth of filter bed is 0.6 m, filtration velocity is less than 12 m/h, ratio of gas to water is 9:11 and sand recycling rate is 2 to 4 mm/min.展开更多
In order to improve the performance of vehicle radiators, a two-dimensional heat transfer steady-state model of the radiator was set up. The influence of the structural parameters (axial ratio) of the heat exchange tu...In order to improve the performance of vehicle radiators, a two-dimensional heat transfer steady-state model of the radiator was set up. The influence of the structural parameters (axial ratio) of the heat exchange tube on the windward side on the heat transfer performance of the radiator was studied. With the increase of the axial ratio of the heat exchange tube on the windward side, the heat exchange capacity of the heat exchange tube surface slightly decreases. The heat exchange area increases significantly, which increases the total heat exchange of the radiator and improves the heat transfer performance of the radiator. When the axial ratio increases from 1.0 to 2.0, the average surface heat transfer capacity decreases from 5664.16</span><span style="font-family:""> </span><span style="font-family:Verdana;">W/m<sup>2</sup> to 5623.57</span><span style="font-family:""> </span><span style="font-family:Verdana;">W/m<sup>2</sup>.展开更多
Combined with the advantages and disadvantages of tuned liquid damper (TLD) and tuned mass damper (TMD),a double tuned liquid mass damper (TLMD) is proposed by replacing the rigid connection of TLD with the spring str...Combined with the advantages and disadvantages of tuned liquid damper (TLD) and tuned mass damper (TMD),a double tuned liquid mass damper (TLMD) is proposed by replacing the rigid connection of TLD with the spring structure.The motion equation of a single-degree-of-freedom structure with a TLMD attached at its top is found under harmonic excitation.Comparing the energy consumption and amplitude of primary structure with equal mass ratio TMD,it is found that the energy dissipation performance of TLMD is better in the effective phase region.The interaction process between TLMD and structure is analyzed,and the formula of phase deviation between the relative velocity of tank and the displacement of primary structure is deduced.By analyzing the influence of mass ratio,frequency ratio,damping ratio and water depth ratio on the damping effect,the results show that the frequency ratio and liquid depth ratio have great influence on the size and location of deep resonance peak,and the mass ratio and damping ratio have great influence on the width of the effective frequency band.The formula of equivalent damping ratio is proposed based on the principle of energy and it is found that the equivalent damping ratio is related to the phase deviation and change with the frequency ratio of the external excitation.展开更多
In this paper, we explore the properties of a positive-part Stein-like estimator which is a stochastically weighted convex combination of a fully correlated parameter model estimator and uncorrelated parameter model e...In this paper, we explore the properties of a positive-part Stein-like estimator which is a stochastically weighted convex combination of a fully correlated parameter model estimator and uncorrelated parameter model estimator in the Random Parameters Logit (RPL) model. The results of our Monte Carlo experiments show that the positive-part Stein-like estimator provides smaller MSE than the pretest estimator in the fully correlated RPL model. Both of them outperform the fully correlated RPL model estimator and provide more accurate information on the share of population putting a positive or negative value on the alternative attributes than the fully correlated RPL model estimates. The Monte Carlo mean estimates of direct elasticity with pretest and positive-part Stein-like estimators are closer to the true value and have smaller standard errors than those with fully correlated RPL model estimator.展开更多
基金National Natural Science Foundation of China under Grant No.51338001Natural Science Foundation of China under Grant Nos.51178028 and 51422801+2 种基金the Fundamental Research Funds for the Central Universities under Grant No.2014YJS087Program for New Century Excellent Talents in University under Grant No.NCET-11-0571111 Project of China under Grant No.B13002
文摘Tibetan heritage buildings have a high historical and cultural value. They have endured adverse environmental loadings over hundreds of years without significant damage. However, there are few reports on their structural characteristics under normal environmental loadings and their behavior under dynamic loadings. In this research, a typical Tibetan wooden wall-frame building is selected to study its dynamic characteristics. Field measurements of the structure were conducted under environmental excitation to collect acceleration responses. The stochastic subspace identification （SSI） method was adopted to calculate the structural modal parameters and obtain the out-of-plane vibration characteristics of the slab and frames. The results indicated that the wall-frame structure had a lower out-of-plane stiffness and greater in-plane stiffness due to the presence of stone walls. Due to poor identified damping ratio estimates from the SSI method, a method based on the variance upper bound was proposed to complement the existing variance lower bound method for estimating the modal damping ratio to address the significant damping variability obtained from different points and measurements. The feasibility of the proposed method was illustrated with the measured data from the floor slab of the structure. The variance lower and upper bound methods both provided consistent results compared to those from the traditional SSI method.
基金Supported by the International Cooperation Program under Grant No.2007DFR80340the National Natural Science Foundation of China under Grant No.50779007
文摘Rigid blocking masses are located in the typical base structure of a power cabin based on the impedance mismatch principle.By combining the acoustic-structural coupling method and statistical energy analysis,the full-band vibration and sound radiation reduction effect of vibration isolation masses located in a base structure was researched.The influence of the blocking mass’ cross-section size and shape parameters and the layout location of the base isolation performance was discussed.Furthermore,the effectiveness of rigid vibration isolation design of the base structure was validated.The results show that the medium and high frequency vibration and sound radiation of a power cabin are effectively reduced by a blocking mass.Concerning weight increment and section requirement,suitably increasing the blocking mass size and section height and reducing section width can result in an efficiency-cost ratio.
基金National Natural Science Foundation of China(12102410)Fund of National Key Laboratory of Shock Wave and Detonation Physics(JCKYS2022212005)。
文摘The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more precise lattice parameters using the interaction points for the pseudo-Kossel pattern obtained from laser-induced X-ray diffraction(XRD).This method has been validated by the analysis of an XRD experiment conducted on iron single crystals.Furthermore,the method was used to calculate the compression ratio and rotated angle of an LiF sample under high pressure loading.This technique provides a robust tool for in-situ characterization of structural changes in single crystals under extreme conditions.It has significant implications for studying the equation of state and phase transitions.
文摘Optimization of structural parameters aimed at improving the load carrying capacity of spatial flexible redundant manipulators is presented in this paper. In order to increase the ratio of load to mass of robots, the cross-sectional parameters and constructional parameters are optimized respectively. The cross-sectional and configurational parameters are optimized simultaneously. The numerical simulation of a 4R spatial manipulator is performed. The results show that the load capacity of robots has been greatly improved through the optimization strategies proposed in this paper.
基金Supported by Major Science and Technology Program of Hainan Province(ZDKJ2016017-01,ZDKJ2016017-03)Youth Science and Technology Talents Innovation Project of Hainan Science&Technology Association(QCXM201802)
文摘[Objective] This paper was to study effects of pelleted total mixed ration with different concentrate-roughage ratios on production performance and serum biochemical parameters of fattening Hainan black goats.[Method] Thirty-six fattening Hainan black goats with the same genetic background and similar initial weight of(14.08±0.13) kg were randomly assigned into three treatments. Goats were fed with Juncao + concentrate(control group), pelleted total mixed ration I(concentrate: roughage 50 ∶50, group Ⅰ) and Ⅱ(concentrate: roughage 45∶55, group Ⅱ), respectively. The test lasted 45 d.[Result] The final weight, daily gain and feed intake of rams in experimental group Ⅰ were significantly higher than those of control group and experimental group Ⅱ(P<0.05);the final weight and daily gain of rams in experimental group Ⅰ were also markedly higher than those of experimental group Ⅱ(P<0.05);the feed/gain of rams in experimental group Ⅰ was significantly lower than those in control group and experimental group Ⅱ(P<0.05). The feed gain cost of rams in experimental group Ⅰ was markedly lower than that in experimental group Ⅱ( P<0.05), but was significantly higher than that in experimental group Ⅰ(P<0.05);the gross profit of rams in experimental group Ⅰ was significantly higher than those in control group and experimental group Ⅱ(P<0.05). Compared with control group and experimental group Ⅱ, the serum total protein and glucose lev-els in experimental group Ⅱ increased significantly(P<0.05), but the urea nitrogen content reduced(P>0.05).[Conclusion] When the concentrateroughage ratio of pelleted total mixed ration was 50∶50, the fattening effect of Hainan black goat was better, and the serum total protein and glucose levels were evidently improved.
基金Project supported by the Natural Science Foundation of China （Key Grant No 10332030） and the National 973 Project of China （Grant No 5132103ZZT21B）.
文摘In this paper conventional stochastic resonance （CSR） is realized by adding the noise intensity. This demonstrates that tuning the system parameters with fixed noise can make the noise play a constructive role and realize parameter- induced stochastic resonance （PSR）. PSR can be interpreted as changing the intrinsic characteristic of the dynamical system to yield the cooperative effect between the stochastic-subjected nonlinear system and the external periodic force. This can be realized at any noise intensity, which greatly differs from CSR that is realized under the condition of the initial noise intensity not greater than the resonance level. Moreover, it is proved that PSR is different from the optimization of system parameters.
文摘To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different casting parameters such as pouring temperature, inoculation, carbon equivalent, moisture content, green compression strength, permeability and mould hardness were selected. Three different melts of metal with 0.4wt.%, 0.6wt.%, and 0.8wt.% inoculation （Fe-Si-Mg alloy and post inoculant） were produced using a 1-ton capacity coreless medium frequency induction furnace. L-27 orthogonal array with 3-level settings were chosen for the analysis. Responses for each run were observed. The signal-to-noise （S/N） ratio for each run was calculated using the Taguchi approach, and the optimized levels of different casting parameters were identified based on the SIN ratio. The analysis of variance for the casting acceptance percentage concludes that inoculation is the most significant factor affecting the castings＇ quality with a contribution percentage of 44%; an increase in inoculation results in a significant improvement in acceptance percentage of ductile iron castings. The experiment results showed that with the optimized parameters, the rejection rate was reduced from 16.98% to 6.07%.
基金sponsored by the National Natural Science Foundation of China(Grant No.40975004)the State Key Basic Program(973)(Grant No.2013CB430100)
文摘Following the parameterization of sheared entrainment obtained in the companion paper, Liu et al. （2016）, the present study aims to further investigate the characteristics of entrainment, and develop a simple model for predicting the growth rate of a well-developed and sheared CBL. The relative stratification, defined as the ratio of the stratification in the free atmosphere to that in the entrainment zone, is found to be a function of entrainment flux ratio （Ae）. This leads to a simple expression of the entrainment rate, in which Ae needs to be parameterized. According to the results in Liu et al. （2016）, Ae can be simply expressed as the ratio of the convective velocity scale in the sheared CBL to that in the shear-free CBL. The parameterization of the convective velocity scale in the sheared CBL is obtained by analytically solving the bulk model with several assumptions and approximations. Results indicate that the entrainment process is influenced by the dynamic effect, the interaction between mean shear and environmental stratification, and one other term that includes the Coriolis effect. These three parameterizations constitute a simple model for predicting the growth rate of a well-developed and sheared CBL. This model is validated by outputs of LESs, and the results show that it performs satisfactorily. Compared with bulk models, this model does not need to solve a set of equations for the CBL. It is more convenient to apply in numerical models.
文摘Hypothesis testing analysis and unknown parameter estimation of both the intermediate frequency(IF) and baseband GPS signal detection are given by using the generalized likelihood ratio test(GLRT) approach,applying the model of GPS signal in white Gaussian noise,It is proved that the test statistic follows central or noncentral F distribution,It is also pointed out that the test statistic is nearly identical to central or noncentral chi-squared distribution because the processing samples are large enough to be considered as infinite in GPS acquisition problem.It is also proved that the probability of false alarm,the probability of detection and the threshold are affected largely when the hypothesis testing refers to the full pseudorandom noise(PRN) code phase and Doppler frequency search space cells instead of each individual cell.The performance of the test statistic is also given with combining the noncoherent integration.
文摘A water rocket is a rocket system that obtains thrust by injecting water with compressed air of up to about 8 atmospheres. It is usually manufactured using a pressure-resistant PET bottle. The mechanical elements and principles contained in the water rocket have much in common with the actual small rocket system, and are suitable as educational and research teaching materials in the field of mechanics. Especially in the field of disaster prevention and mitigation, the use of water rockets is being researched and developed as a rescue tool in the event of a flood or earthquake as a disaster countermeasure. However, since the water rocket is a flying object based on the mechanical principle, it is important to ensure the accuracy and stability of the flight path. In this paper, a mechanical simulator is developed with a numerical calculation program based on the mechanical consideration of water rocket flight performance. In addition, the correlation between the flight distance obtained in the simulation and the estimated flight distance is analyzed by applying a multivariate analysis method and verifying the validity of the flight distance calculated from the result. Based on the verification results, we will apply a statistical optimization method to approach the optimization of flight stability performance conditions for water rockets.
基金the National Natural Science Foundation of China(Grant Nos.61973037 and 61673066).
文摘Conventional parameter estimation methods for pseudo-random binary code-linear frequency modulation(PRBC-LFM)signals require prior knowledge,are computationally complex,and exhibit poor performance at low signal-to-noise ratios(SNRs).To overcome these problems,a blind parameter estimation method based on a Duffing oscillator array is proposed.A new relationship formula among the state of the Duffing oscillator,the pseudo-random sequence of the PRBC-LFM signal,and the frequency difference between the PRBC-LFM signal and the periodic driving force signal of the Duffing oscillator is derived,providing the theoretical basis for blind parameter estimation.Methods based on amplitude method,short-time Fourier transform method,and power spectrum entropy method are used to binarize the output of the Duffing oscillator array,and their performance is compared.The pseudo-random sequence is estimated using Duffing oscillator array synchronization,and the carrier frequency parameters are obtained by the relational expressions and characteristics of the difference frequency.Simulation results show that this blind estimation method overcomes limitations in prior knowledge and maintains good parameter estimation performance up to an SNR of-35 dB.
基金Indian National Centre for Ocean Information Services(INCOIS)of the Ministry of Earth Science of Indiathe INSPIRE fellowship of Department of Science and Technology of India
文摘The spatial distribution of physico-chemical parameters（sea surface temperature（SST）, p H, sea surface salinity（SSS）, dissolved oxygen（DO） and Secchi depth） along with filterable nutrients（dissolved inorganic nitrate（DIN）,dissolved inorganic phosphate（DIP） and reactive silicate（DSi）） are measured in the winter months of November,December, January and February for four consecutive years from 2009–2010 to 2012–2013 on the shallow continental shelf（〈20 m bathymetry） of the coastal waters（up to 18 km away from shoreline） of the northern Bay of Bengal（n Bo B） during the highest high tide（HHT） and lowest low tide（LLT） hours for the first time. The variability of the coastal biogeochemical environment is assessed during the HHT and LLT hours and for this purpose, seawater samples are collected from seven different locations of a transect in the coastal region. Physicochemical parameters（except SST） show significant difference in magnitude during the HHT and LLT hours respectively. p H, SSS and DO are found to increase in the HHT hours and vice-versa. The data reveal that during the LLT hours, a relative increase of freshwater input in the n Bo B can have elevated the nutrient concentration compared with that observed during the HHT hours. The ratio of nutrient concentration is found to deviate significantly from the Redfield ratio. The abundance of DIP is much higher compared with that of DIN and DSi.The anthropogenic sources of DIP from the upstream flow（especially the domestic effluent of several metropolises） can be mainly attributed behind such an observation. In order to characterize and establish the trend of such variation in such an important bio-climatic region, long-term and systematic ecosystem monitoring in the coastal water of the n Bo B northern Bay of Bengal should be carried out throughout the year.
基金supported by the Innovation Program for 2011 College Graduates of Jiangsu Province(Grant No.CXZZ_0158)the National Natural Science Foundation of China(Grant No.51178107)
文摘A method of obtaining the large strain consolidation parameters of dredged clays considering the influence of the initial water content is investigated in this study. According to the test results of remolded clays with high initial water contents reported by Hong et al. （2010）, a relationship between the void ratio （e） and effective stress （a3 is established. Furthermore, based on the available permeability data from the literature, a new relationship between the permeability coefficient （k） and the ratio （e/eL） of the void ratio to the void ratio at the liquid limit （eL） is proposed. The new proposed expression considering the initial water content improves the e-k equation established by Nagaraj et al. （1994）. Finally, the influence of the initial void ratio and effective stress on the large strain consolidation coefficient g（e） defined by Gibson et al. （1981） and k/（1 ＋e） in large strain analysis is discussed. The results show that, under a constant effective stress, the value of k/（1 ＋e） increases with the initial void ratio. The large strain consolidation coefficient shows the law of segmentation change, which decreases with the increase of the effective stress when the effective stress is less than the remolded yield stress, but increases rapidly with the effective stress when the effective stress is larger than the remolded yield stress.
基金Supported by the National Natural Science Foundation of China(No.31872609)the Innovation Support Program for High-level Talents of Dalian City(No.2019RD12)+1 种基金the Key Research Project of Liaoning Provincial Department of Education in 2022(No.LJKZZ 20220091)the earmarked fund for CARS-49(CARS-49)。
文摘To adapt to the change of aquaculture workshop site,optimize the shape of aquaculture tanks and improve the utilization rate of breeding space,it is necessary to determine the appropriate length width ratio parameters of aquaculture tanks.In this paper,computational fluid dynamics(CFD)technology is adopted to study the flow field performance of aquaculture tanks with different L/B ratios(L:the length;B:the width,of aquaculture tank)and different jet direction conditions(lengthways jet and widthways jet).A three-dimensional numerical calculation model of turbulence in rounded rectangle aquaculture tanks in dual-diagonal-inlet layout was established.Jet directions are arranged lengthways and widthways,and the water flow velocity,resistance coefficient change,vorticity,etc.are analyzed under two working conditions.Results show that the flow field performance in aquaculture tank decreases with the increase of the L/B ratio.The flow field performed well when L/B was 1.0-1.3,sharply dropped at 1.4-1.6,and poor at 1.7-1.9.The results provided a theoretical basis for the design and optimization in flow field performance of the industrialized circulating aquaculture tanks.
文摘The main targets of seismic exploration research in Leijia carbonatite tight sandstone oil area of Liaohe depression are thin reservoirs prediction and minor faults identification, which is one of the important representatives of complex exploration objects in Liaohe depression. High precision 3D seismic exploration has significantly improved the ability of thin reservoirs prediction and minor faults identification of this area. Reducing the cost of high precision 3D seismic exploration through optimizing the acquisition parameters is very important for the next step exploration and development of Liaohe depression and similar areas. Based on high precision 3D seismic acquisition data in Leijia tight sandstone oil area, multiple sub-geometries are obtained with different bin sizes, different folds, different aspect ratio, different line intervals by extracting receiver points and shot points, and PSTM processing is performed respectively, obtained PSTM datasets of the sub-geometries, extract time slices, amplitude slices along the layer, coherent slices and so on. We evaluate the data results of the sub-geometries from the aspects of signal-to-noise ratio, thin reservoirs resolution, acquisition footprint and so on. Considering the exploration cost and data effect of each sub-geometry, the optimal direction of the main parameters of high precision seismic exploration in Liaohe depression is put forward, and the acquisition effect of adjacent area by the optimized parameters is given.
文摘In this paper, the parameter estimation problem is investigated for the continuous time stochastic logistic diffusion system. A new continuous process is built based on the likelihood ratio scheme, the Radon-Nikodym derivative and the explicit expressions of the error of estimation are given under this new continuous process. By using the random time transformations, law of large numbers for martingales, law of iterated logarithm and stationary distribution of solution, the consistency property are proved for the estimation error. Finally, a numerical simulation is presented to demonstrate the effectiveness of the proposed method in this paper.
文摘A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and backwashing. The design and operation parameters, which affect the performance of the filter, are discussed. The key design parameters are provided as follows: diameter of filter material is 0.7 to 1.0 mm, depth of filter bed is 0.6 m, filtration velocity is less than 12 m/h, ratio of gas to water is 9:11 and sand recycling rate is 2 to 4 mm/min.
文摘In order to improve the performance of vehicle radiators, a two-dimensional heat transfer steady-state model of the radiator was set up. The influence of the structural parameters (axial ratio) of the heat exchange tube on the windward side on the heat transfer performance of the radiator was studied. With the increase of the axial ratio of the heat exchange tube on the windward side, the heat exchange capacity of the heat exchange tube surface slightly decreases. The heat exchange area increases significantly, which increases the total heat exchange of the radiator and improves the heat transfer performance of the radiator. When the axial ratio increases from 1.0 to 2.0, the average surface heat transfer capacity decreases from 5664.16</span><span style="font-family:""> </span><span style="font-family:Verdana;">W/m<sup>2</sup> to 5623.57</span><span style="font-family:""> </span><span style="font-family:Verdana;">W/m<sup>2</sup>.
基金the National Natural Science Foundation of China(Nos.51578434 and 51378500)。
文摘Combined with the advantages and disadvantages of tuned liquid damper (TLD) and tuned mass damper (TMD),a double tuned liquid mass damper (TLMD) is proposed by replacing the rigid connection of TLD with the spring structure.The motion equation of a single-degree-of-freedom structure with a TLMD attached at its top is found under harmonic excitation.Comparing the energy consumption and amplitude of primary structure with equal mass ratio TMD,it is found that the energy dissipation performance of TLMD is better in the effective phase region.The interaction process between TLMD and structure is analyzed,and the formula of phase deviation between the relative velocity of tank and the displacement of primary structure is deduced.By analyzing the influence of mass ratio,frequency ratio,damping ratio and water depth ratio on the damping effect,the results show that the frequency ratio and liquid depth ratio have great influence on the size and location of deep resonance peak,and the mass ratio and damping ratio have great influence on the width of the effective frequency band.The formula of equivalent damping ratio is proposed based on the principle of energy and it is found that the equivalent damping ratio is related to the phase deviation and change with the frequency ratio of the external excitation.
文摘In this paper, we explore the properties of a positive-part Stein-like estimator which is a stochastically weighted convex combination of a fully correlated parameter model estimator and uncorrelated parameter model estimator in the Random Parameters Logit (RPL) model. The results of our Monte Carlo experiments show that the positive-part Stein-like estimator provides smaller MSE than the pretest estimator in the fully correlated RPL model. Both of them outperform the fully correlated RPL model estimator and provide more accurate information on the share of population putting a positive or negative value on the alternative attributes than the fully correlated RPL model estimates. The Monte Carlo mean estimates of direct elasticity with pretest and positive-part Stein-like estimators are closer to the true value and have smaller standard errors than those with fully correlated RPL model estimator.
