This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The exp...This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The explicit dispersion relations are derived for the two cases when the propagation directions of SH waves are normal to the interface and parallel to the interface, respectively. The asymptotic expressions for dispersion relations are also given when the wave number is extremely small. Numerical results for stop band effect and phase velocity are presented for a periodic system of alternating BaTiO3 and Terfenol-D layers. The influence of volume fraction on stop band effect and dispersion behaviors is discussed and revealed.展开更多
Investigation of infiltration through unsaturated zone which consists of both porous and fractured media is important for comprehensively understanding water circulation and effectively man- aging groundwater resource...Investigation of infiltration through unsaturated zone which consists of both porous and fractured media is important for comprehensively understanding water circulation and effectively man- aging groundwater resources and contamination control. Infiltration experiments for three kinds of porous-fractured layered structures were conducted with application of a rainfall simulator in this in- vestigation. During experiments, the volumetric water contents of porous media and on the interface of porous-fractured media were monitored by moisture sensors （TDT）. The infiltration rate, water amount in the profile and on the interface between the soil and the fractured bedrock, and outflow from the layered structures were analyzed to identify the effects of porous-fractured interface on water movement in the upper porous media and the effects of various kinds of porous media on infiltration in fractured rocks. It has been observed from the experiment results that the porous media and the frac- tured rock bear considerable reciprocal impact each other on infiltration processes and water content distribution. The results showed fractured rock prevented vertical water movement in the layered structure, and it decreases infiltration rate of layered structure and slows the process for upper porous media saturation.展开更多
Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-l...Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.展开更多
This study focuses on steeply inclined and extremely thick coal seams(SIETCS)characterized by immense thickness,a steep inclination of coal seams(87°),and high horizontal stress.The geological conditions and mini...This study focuses on steeply inclined and extremely thick coal seams(SIETCS)characterized by immense thickness,a steep inclination of coal seams(87°),and high horizontal stress.The geological conditions and mining technology associated with SIETCS differ significantly from those of generally inclined coal seams,resulting in notable variations in roadway stress distributions.On SIETCS have predominantly examined the impact of rock layers flanking coal seams on rock bursts,with limited emphasis on SIETCS roadways.This study employs comprehensive methods,integrating numerical simulations,theoretical analyses,and field detections to investigate the stress distribution of SIETCS and the mechanisms of rock burst-induced vertical damage,subsequently validated in situ.The vertical stress in SIETCS is minimal,while horizontal stress is concentrated,leading to the formation of layered crack structures(LCS)that distribute above and below the roadways.Additionally,elastic energy significantly concentrates within the LCS.Axial dynamic compressive stress and vertical dynamic tensile stress along the LCS diminish its stability,readily triggering failure.During the LCS failure process,the stored energy is released,converting into kinetic energy required for coal body ejection after reaching the minimum energy for failure and dissipative energy,ultimately leading to rock burst-induced vertical damage in roadways.On-site detection and analysis within SIETCS,along with historical rock burst data,confirm the existence of LCS and its role in inducing vertical rock burst damage.This research establishes essential foundations for preventing rock bursts within SIETCS.展开更多
The morphological distribution of absorbent in composites is equally important with absorbents for the overall electromagnetic properties,but it is often ignored.Herein,a comprehensive consideration including electrom...The morphological distribution of absorbent in composites is equally important with absorbents for the overall electromagnetic properties,but it is often ignored.Herein,a comprehensive consideration including electromagnetic component regulation,layered arrangement structure,and gradient concentration distribution was used to optimize impedance matching and enhance electromagnetic loss.On the microscale,the incorporation of magnetic Ni nanoparticles into MXene nanosheets(Ni@MXene)endows suitable intrinsic permittivity and permeability.On the macroscale,the layered arrangement of Ni@MXene increases the effective interaction area with electromagnetic waves,inducing multiple reflection/scattering effects.On this basis,according to the analysis of absorption,reflection,and transmission(A-R-T)power coefficients of layered composites,the gradient concentration distribution was constructed to realize the impedance matching at low-concentration surface layer,electromagnetic loss at middle concentration interlayer and microwave reflection at high-concentration bottom layer.Consequently,the layered gradient composite(LG5-10-15)achieves complete absorption coverage of X-band at thickness of 2.00-2.20 mm with RL_(min) of-68.67 dB at 9.85 GHz in 2.05 mm,which is 199.0%,12.6%,and 50.6%higher than non-layered,layered and layered descending gradient composites,respectively.Therefore,this work confirms the importance of layered gradient structure in improving absorption performance and broadens the design of high-performance microwave absorption materials.展开更多
Carbonaceous material has attracted much attention in the application of sodium-ion batteries(SIBs)anode.However,sluggish reaction kinetics and structure stability impede the application.Therefore,a stacked layered su...Carbonaceous material has attracted much attention in the application of sodium-ion batteries(SIBs)anode.However,sluggish reaction kinetics and structure stability impede the application.Therefore,a stacked layered sulfur-carbon complex with long-chain C–S_(x)–C bond(M-SC-S)is prepared.The layered structure ensures structural stability,and long-chain C–S_(x)–C bond expanding interlayer spacing boosts facile Na+diffusion.When assembled into cells,a high-quality solid-electrolyte interphase film would be formed due to a good match between the M-SC-S electrode and ether electrolyte.Moreover,an electrochemical activation process would happen between the Cu current collector and proper S-doped electrode material to in-situ form Cu_(2)S.The formation of Cu_(2)S in active material can not only provide more active sites for sodium storage and enhance pseudo-capacitance,but also reinforce the electrode/current collector interface and decrease the interfacial transfer resistance for rapid Na+kinetics.The synergistic effect of structure design and interface engineering optimizes the sodium storage system.Thus,the M-SC-S electrode delivers an excellent cyclic performance(321.6 mAh g^(−1)after 1000 cycles at 2 A g^(−1)with a capacity retention rate of 97.4%)and good rate capability(282.8 mAh g^(−1)after 4000 cycles even at a high current density of 10 A g^(−1)).The full cell also has an impressive cyclic performance(151.4 mAh g^(−1)after 500 cycles at 0.5 A g^(−1)).展开更多
The recently reported silicon/graphite(Si/Gr)composite electrode with a layered structure is a promising approach to achieve high capacity and stable cycling of Si-based electrodes in lithium-ion batteries.However,the...The recently reported silicon/graphite(Si/Gr)composite electrode with a layered structure is a promising approach to achieve high capacity and stable cycling of Si-based electrodes in lithium-ion batteries.However,there is still a need to clarify why particular layered structures are effective and why others are ineffective or even detrimental.In this work,an unreported mechanism dominated by the porosity evolution of electrodes is proposed for the degradation behavior of layered Si/Gr electrodes.First,the effect of layering sequence on the overall electrode performance is investigated experimentally,and the results suggest that the cycling performance of the silicon-on-graphite(SG)electrode is much superior to that of the graphite-on-silicon electrode.To explain this phenomenon,a coupled mechanical-electrochemical porous electrode model is developed,in which the porosity is affected by the silicon expansion and the local constraints.The modeling results suggest that the weaker constraint of the silicon layer in the SG electrode leads to a more insignificant decrease in porosity,and consequently,the more stable cycling performance.The findings of this work provide new insights into the structural design of Si-based electrodes.展开更多
Due to excellent thermal insulation performance at room temperature and ultralow density,silica aero-gels are candidates for thermal insulation.However,at high temperatures,the thermal insulation prop-erty of silica a...Due to excellent thermal insulation performance at room temperature and ultralow density,silica aero-gels are candidates for thermal insulation.However,at high temperatures,the thermal insulation prop-erty of silica aerogels decreased greatly caused by transparency to heat radiation.Opacifiers introduced into silica sol can block heat radiation yet destroy the uniformity of aerogels.Herein,we designed and prepared a silica aerogel composite with oriented and layered silica fibers(SFs),SiC nanowires(SiC_(NWs)),and silica aerogels,which were prepared by papermaking,chemical vapor infiltration(CVI),and sol-gel respectively.Firstly,oriented and layered SFs made still air a wall to block heat transfer by the solid phase.Secondly,SiC_(NWs) were grown in situ on the surface of SFs evenly to weave into the network,and the network reduced the gaseous thermal conductivity by dividing cracks in SFs/SiC_(NWs)/SA.Thirdly,SiC_(NWs) weakened the heat transfer by radiation at high temperatures.Therefore,SFs/SiC_(NWs)/SA presented remarkable thermal insulation(0.017 W(m K)^(-1) at 25℃,0.0287 W(m K)^(-1) at 500℃,and 0.094 W(m K)^(-1) at 1000℃).Besides,SFs/SiC_(NWs)/SA exhibited remarkable thermal stability(no size transform after being heat treated at 1000℃ for 1800 s)and tensile strength(0.75 MPa).These integrated properties made SFs/SiC_(NWs)/SA a promising candidate for highly efficient thermal insulators.展开更多
This paper theoretically investigates the influence of a cylindrical PN junction on the propagation characteristics of shear cylindrical waves(SCWs)in an infinitely long piezoelectric semiconductor(PS)concentric cylin...This paper theoretically investigates the influence of a cylindrical PN junction on the propagation characteristics of shear cylindrical waves(SCWs)in an infinitely long piezoelectric semiconductor(PS)concentric cylinder structure.This PS concentric cylinder structure is composed of three regions:an inner PS cylinder,an outer PS cylindrical shell,and a cylindrical PN junction at the interface between the two aforementioned regions.First,the basic equations of the PS concentric cylinder structure are derived,taking into account the coupling of the mechanical displacement,electric potential,and charge carrier perturbation in the cylindrical coordinate system.Next,a mathematical model for the SCWs in this PS concentric cylinder structure is established,utilizing the spectral method and considering the physical characteristics of the cylindrical PN junction.Finally,the dispersion and attenuation curves of the SCWs are numerically calculated to discuss the influence of the interface effect resulting from the cylindrical PN junction.It is found that the existence of a cylindrical PN junction can either reduce or enhance the mechanical-to-electrical energy conversion,which is closely related to the doping mode,doping concentration,and curvature radius of the cylindrical interface.A reasonable design of the aforementioned parameters can optimize the wave motion in acoustic equipment formed by PS media with different frequencies or wavelengths.The construction and resolution of the mathematical model as well as the analysis of physical mechanisms can offer theoretical guidance for improving the efficiency of energy conversion from mechanical energy to electrical energy and optimizing the acoustic performance of energy harvesting devices.展开更多
Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to...Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.展开更多
The present paper presents an innovative approach for the numerical modeling of piezo-electric transducers for the health-monitoring of layered structures.The numerical approach has been developed in the frameworks of...The present paper presents an innovative approach for the numerical modeling of piezo-electric transducers for the health-monitoring of layered structures.The numerical approach has been developed in the frameworks of the Carrera Unified Formulation.This computa-tional tool allows refined numerical models to be derived in a unified and efficient fashion.The use of higher-order models and the cap-ability to connect different kinematic models using the node-depen-dent kinematic approach has led to an efficient modeling technique for global-local analysis.This approach can refine the model only in those regions where it is required,e.g.,the areas where piezo-electric transducers are placed.The model has been used to study embedded and surface-mounted sensors.The accuracy of the pre-sent model has been verified by comparing the current results with numerical and experimental data from the literature.Different mod-eling solutions have been developed,mixing one-,two-and threedimensional finite elements.The results show that the use of the present modeling technique allows the computational cost to be reduced with respect to the classical approaches preserving the ccuracy of the results in the critical areas.展开更多
Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are c...Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are considered. The transfer matrices between two consecutive unit cells are obtained according to the continuity conditions. The expressions of localization factor and localization length in the disordered periodic structures are presented. For the disordered periodic piezoelectric structures, the numerical results of localization factor and localization length are presented and discussed. It can be seen from the results that the frequency passbands and stopbands appear for the ordered periodic structures and the wave localization phenomenon occurs in the disordered periodic ones, and the larger the coefficient of variation is, the greater the degree of wave localization is. The widths of stopbands in the ordered periodic structures are very narrow when the properties of the consecutive piezoelectric materials are similar and the intervals of stopbands become broader when a certain material parameter has large changes. For the wave propagating in the direction normal to the layers the localization length has less dependence on the frequency, but for the wave propagating in the direction tangential to the layers the localization length is strongly dependent on the frequency.展开更多
The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effec...The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effects of the initial stresses on the phase velocity and theelectromechanical coupling coefficient for the fundamental mode of the layered piezoelectricstructures are discussed. Numerical results for the c-axis oriented film of LiNbO_3 on a sapphiresubstrate are given. It is found that the fractional change in phase velocity is a linear functionwith the initial stresses, and the electromechanical coupling factor increases with an increase ofthe absolute values of the compressive initial stresses. The results are useful for the design ofsurface acoustic wave devices.展开更多
Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devi...Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devices(PEDs),etc.In recent decades,Lithium-ion batteries(LIBs) have been extensively utilized in largescale energy storage devices owing to their long cycle life and high energy density.However,the high cost and limited availability of Li are the two main obstacles for LIBs.In this regard,sodium-ion batteries(SIBs) are attractive alternatives to LIBs for large-scale energy storage systems because of the abundance and low cost of sodium materials.Cathode is one of the most important components in the battery,which limits cost and performance of a battery.Among the classified cathode structures,layered structure materials have attracted attention because of their high ionic conductivity,fast diffusion rate,and high specific capacity.Here,we present a comprehensive review of the classification of layered structures and the preparation of layered materials.Furthermore,the review article discusses extensively about the issues of the layered materials,namely(1) electrochemical degradation,(2) irreversible structural changes,and(3) structural instability,and also it provides strategies to overcome the issues such as elemental phase composition,a small amount of elemental doping,structural design,and surface alteration for emerging SIBs.In addition,the article discusses about the recent research development on layered unary,binary,ternary,quaternary,quinary,and senary-based O3-and P2-type cathode materials for high-energy SIBs.This review article provides useful information for the development of high-energy layered sodium transition metal oxide P2 and O3-cathode materials for practical SIBs.展开更多
It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites incl...It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites including those inspired by gradient layered materials.In this work,we used LPBF to selectively prepare Ti N/Ti gradient layered structure(GLSTi)composites by using different N_(2)–Ar ratios during the LPBF process.We systematically investigated the mechanisms of in-situ synthesis Ti N,high strength and ductility of GLSTi composites using microscopic analysis,TEM characterization,and tensile testing with digital image correlation.Besides,a digital correspondence was established between the N_(2) concentration and the volume fraction of LPBF in-situ synthesized Ti N.Our results show that the GLSTi composites exhibit superior mechanical properties compared to pure titanium fabricated by LPBF under pure Ar.Specifically,the tensile strength of GLSTi was more than 1.5times higher than that of LPBF-formed pure titanium,reaching up to 1100 MPa,while maintaining a high elongation at fracture of 17%.GLSTi breaks the bottleneck of high strength but low ductility exhibited by conventional nanoceramic particle-strengthened titanium matrix composites,and the hetero-deformation induced strengthening effect formed by the Ti N/Ti layered structure explained its strength-plasticity balanced principle.The microhardness exhibits a jagged variation of the relatively low hardness of 245 HV0.2 for the pure titanium layer and a high hardness of 408 HV0.2 for the N_(2) in-situ synthesis layer.Our study provides a new concept for the structure-performance digital customization of 3D-printed Ti-based composites.展开更多
In this study,we performed first-principles calculations using the VASP(Vienna Ab initio Simulation)software package to investigate the crystal structure,electronic structure,and optical properties of a new layered te...In this study,we performed first-principles calculations using the VASP(Vienna Ab initio Simulation)software package to investigate the crystal structure,electronic structure,and optical properties of a new layered ternary metal chalcogenide,Eu_(2)InTe_(5).Our results show that Eu_(2)InTe_(5) is a non-zero-gap metal with a layered structure characterized by strong intra-layer atomic bonding and weak inter-layer interaction,which suggests its potential application as a nanomaterial.We also studied the optical properties,including the absorption coefficient,imaginary and real parts of the complex dielectric constant,and found that Eu_(2)InTe_(5) exhibits strong photoresponse characteristics at the junction of ultraviolet and visible light as well as blue-green light,with peaks at wavelengths of 389 nm and 477 nm.This suggests that it could be used in the development of UV(ultraviolet)detectors and other optoelectronic devices.Furthermore,due to its strong absorption,low loss,and low reflectivity,Eu_(2)InTe_(5) has the potential to be used as a promising photovoltaic absorption layer in solar cells.展开更多
The limited metal-polymer interlaminar property is a significant obstacle to the advancement of Ti/Carbon Fiber(CF)/Polyether Ether Ketone(PEEK)hybrid laminates.We report for the first time a novel method by utilizing...The limited metal-polymer interlaminar property is a significant obstacle to the advancement of Ti/Carbon Fiber(CF)/Polyether Ether Ketone(PEEK)hybrid laminates.We report for the first time a novel method by utilizing the mussel-inspired Polydopamine(PDA)to introduce a strong chemical-physical bonding between titanium and PEEK.The enhanced Fiber-Metal Laminate(FML)exhibits a significant 48.82%enhancement in Interlaminar Shear Strength(ILSS).In addition,it alters the failure mode of the FML from single metal-resin interlaminar delamination to a multi-mechanism,including debonding,delamination of different composite layers,leading to a 28.57%improvement in maximum displacement.展开更多
To meet the evolving demands of aeroengine development,the structural and performance requirements for ceramic cores have become increasingly stringent.Vat photopolymerization 3D printing,owing to its moldless,fiexibl...To meet the evolving demands of aeroengine development,the structural and performance requirements for ceramic cores have become increasingly stringent.Vat photopolymerization 3D printing,owing to its moldless,fiexible manufacturing,and other advantages,demonstrates significant potential in the preparation of ceramic cores with intricate structures.However,its practical application still faces multiple challenges,including layered structures and property anisotropy,defects such as cracks and collapse during printing and sintering,forming inaccuracies,and difficulties in controlling surface roughness.Recent advances have focused on optimizing slurry formulation and rheology,improving curing behavior,introducing auxiliary powders and additives,tailoring forming parameters,and optimizing the sintering process.Nevertheless,effectively suppressing lamellar defects,achieving superior dimensional accuracy,and maintaining high surface quality in complex structures remain the core scientific and technical issues to be solved.Future research should concentrate on refining curing mechanisms,advancing powder design and organic system optimization,and regulating the coupled processes of forming,debinding,and sintering to accelerate the application of VPP 3D printed ceramic cores in aerospace manufacturing.展开更多
Layered Li[Ni1/3Co1/3Mn1/3]O2 was synthesized with complex metal hydroxide precursors that were prepared by a co-precipitation method.The influence of coordination between ammonia and transition-metal cations on the s...Layered Li[Ni1/3Co1/3Mn1/3]O2 was synthesized with complex metal hydroxide precursors that were prepared by a co-precipitation method.The influence of coordination between ammonia and transition-metal cations on the structural and electrochemical properties of the Li[Ni1/3Co1/3Mn1/3]O2 materials was studied.It is found that when the molar ratio of ammonia to total transition-metal cations is 2.7：1,uniform particle size distribution of the complex metal hydroxide is observed via scanning electron microscopy.The average particle size of Li[Ni1/3Co1/3Mn1/3]O2 materials was measured to be about 500 nm,and the tap-density was measured to be approximately 2.37 g/cm3,which is comparable with that of commercialized LiCoO2.XRD analysis indicates that the presently synthesized Li[Ni1/3Co1/3Mn1/3]O2 has a hexagonal layered-structure.The initial discharge capacity of the Li[Ni1/3Co1/3Mn1/3]O2 positive-electrode material is determined to be 181.5 mA·h/g using a Li/Li[Ni1/3Co1/3Mn1/3]O2 cell operated at 0.1C in the voltage range of 2.8-4.5 V.The discharge capacity at the 50th cycle at 0.5C is 170.6 mA·h/g.展开更多
Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The igniti...Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The ignition resistance of these alloys often depends on the protectiveness of the oxide film formed on the surface.This paper elucidates the formation mechanism of oxide film from thermodynamics and kinetics,classifying oxide films based on their layered structure to assess their protective properties.Furthermore,it comprehensively reviews the impact of characteristics on the protective effectiveness such as compactness,continuity,thickness,and mechanical properties.The paper also introduces various characterization methods for the microstructure and properties of oxide film.The primary objective of this paper is to enhance the comprehension of oxide film concerning the ignition resistance of Mg alloys and to furnish references for future advancements and research in Mg alloys with heightened ignition resistance.展开更多
基金supported by the National Natural Science Foundation of China (Nos.10672108,10572069 and 10820101048)
文摘This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The explicit dispersion relations are derived for the two cases when the propagation directions of SH waves are normal to the interface and parallel to the interface, respectively. The asymptotic expressions for dispersion relations are also given when the wave number is extremely small. Numerical results for stop band effect and phase velocity are presented for a periodic system of alternating BaTiO3 and Terfenol-D layers. The influence of volume fraction on stop band effect and dispersion behaviors is discussed and revealed.
基金supported by the Major State Basic Research Development Program of China(973 Program)(No.2010CB428804)the National Natural Science Foundation of China(No.40972166)the Major Science and Technology Program for Water Pollution Control and Treatment of China(No.2009ZX07212-003)
文摘Investigation of infiltration through unsaturated zone which consists of both porous and fractured media is important for comprehensively understanding water circulation and effectively man- aging groundwater resources and contamination control. Infiltration experiments for three kinds of porous-fractured layered structures were conducted with application of a rainfall simulator in this in- vestigation. During experiments, the volumetric water contents of porous media and on the interface of porous-fractured media were monitored by moisture sensors （TDT）. The infiltration rate, water amount in the profile and on the interface between the soil and the fractured bedrock, and outflow from the layered structures were analyzed to identify the effects of porous-fractured interface on water movement in the upper porous media and the effects of various kinds of porous media on infiltration in fractured rocks. It has been observed from the experiment results that the porous media and the frac- tured rock bear considerable reciprocal impact each other on infiltration processes and water content distribution. The results showed fractured rock prevented vertical water movement in the layered structure, and it decreases infiltration rate of layered structure and slows the process for upper porous media saturation.
文摘Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.
基金support of the National Natural Science Foundation of China(52374180,52327804).
文摘This study focuses on steeply inclined and extremely thick coal seams(SIETCS)characterized by immense thickness,a steep inclination of coal seams(87°),and high horizontal stress.The geological conditions and mining technology associated with SIETCS differ significantly from those of generally inclined coal seams,resulting in notable variations in roadway stress distributions.On SIETCS have predominantly examined the impact of rock layers flanking coal seams on rock bursts,with limited emphasis on SIETCS roadways.This study employs comprehensive methods,integrating numerical simulations,theoretical analyses,and field detections to investigate the stress distribution of SIETCS and the mechanisms of rock burst-induced vertical damage,subsequently validated in situ.The vertical stress in SIETCS is minimal,while horizontal stress is concentrated,leading to the formation of layered crack structures(LCS)that distribute above and below the roadways.Additionally,elastic energy significantly concentrates within the LCS.Axial dynamic compressive stress and vertical dynamic tensile stress along the LCS diminish its stability,readily triggering failure.During the LCS failure process,the stored energy is released,converting into kinetic energy required for coal body ejection after reaching the minimum energy for failure and dissipative energy,ultimately leading to rock burst-induced vertical damage in roadways.On-site detection and analysis within SIETCS,along with historical rock burst data,confirm the existence of LCS and its role in inducing vertical rock burst damage.This research establishes essential foundations for preventing rock bursts within SIETCS.
基金support for this work by Key Research and Development Project of Henan Province(Grant.No.241111232300)the National Natural Science Foundation of China(Grant.No.52273085 and 52303113)the Open Fund of Yaoshan Laboratory(Grant.No.2024003).
文摘The morphological distribution of absorbent in composites is equally important with absorbents for the overall electromagnetic properties,but it is often ignored.Herein,a comprehensive consideration including electromagnetic component regulation,layered arrangement structure,and gradient concentration distribution was used to optimize impedance matching and enhance electromagnetic loss.On the microscale,the incorporation of magnetic Ni nanoparticles into MXene nanosheets(Ni@MXene)endows suitable intrinsic permittivity and permeability.On the macroscale,the layered arrangement of Ni@MXene increases the effective interaction area with electromagnetic waves,inducing multiple reflection/scattering effects.On this basis,according to the analysis of absorption,reflection,and transmission(A-R-T)power coefficients of layered composites,the gradient concentration distribution was constructed to realize the impedance matching at low-concentration surface layer,electromagnetic loss at middle concentration interlayer and microwave reflection at high-concentration bottom layer.Consequently,the layered gradient composite(LG5-10-15)achieves complete absorption coverage of X-band at thickness of 2.00-2.20 mm with RL_(min) of-68.67 dB at 9.85 GHz in 2.05 mm,which is 199.0%,12.6%,and 50.6%higher than non-layered,layered and layered descending gradient composites,respectively.Therefore,this work confirms the importance of layered gradient structure in improving absorption performance and broadens the design of high-performance microwave absorption materials.
基金supported by the Key Research and Development Program of Wuhan(2025010102030005)the National Nature Science Foundation of Jiangsu Province(BK20221259)。
文摘Carbonaceous material has attracted much attention in the application of sodium-ion batteries(SIBs)anode.However,sluggish reaction kinetics and structure stability impede the application.Therefore,a stacked layered sulfur-carbon complex with long-chain C–S_(x)–C bond(M-SC-S)is prepared.The layered structure ensures structural stability,and long-chain C–S_(x)–C bond expanding interlayer spacing boosts facile Na+diffusion.When assembled into cells,a high-quality solid-electrolyte interphase film would be formed due to a good match between the M-SC-S electrode and ether electrolyte.Moreover,an electrochemical activation process would happen between the Cu current collector and proper S-doped electrode material to in-situ form Cu_(2)S.The formation of Cu_(2)S in active material can not only provide more active sites for sodium storage and enhance pseudo-capacitance,but also reinforce the electrode/current collector interface and decrease the interfacial transfer resistance for rapid Na+kinetics.The synergistic effect of structure design and interface engineering optimizes the sodium storage system.Thus,the M-SC-S electrode delivers an excellent cyclic performance(321.6 mAh g^(−1)after 1000 cycles at 2 A g^(−1)with a capacity retention rate of 97.4%)and good rate capability(282.8 mAh g^(−1)after 4000 cycles even at a high current density of 10 A g^(−1)).The full cell also has an impressive cyclic performance(151.4 mAh g^(−1)after 500 cycles at 0.5 A g^(−1)).
基金supported by the National Natural Science Foundation of China(Grant Nos.12072183,12472174,and 12421002).
文摘The recently reported silicon/graphite(Si/Gr)composite electrode with a layered structure is a promising approach to achieve high capacity and stable cycling of Si-based electrodes in lithium-ion batteries.However,there is still a need to clarify why particular layered structures are effective and why others are ineffective or even detrimental.In this work,an unreported mechanism dominated by the porosity evolution of electrodes is proposed for the degradation behavior of layered Si/Gr electrodes.First,the effect of layering sequence on the overall electrode performance is investigated experimentally,and the results suggest that the cycling performance of the silicon-on-graphite(SG)electrode is much superior to that of the graphite-on-silicon electrode.To explain this phenomenon,a coupled mechanical-electrochemical porous electrode model is developed,in which the porosity is affected by the silicon expansion and the local constraints.The modeling results suggest that the weaker constraint of the silicon layer in the SG electrode leads to a more insignificant decrease in porosity,and consequently,the more stable cycling performance.The findings of this work provide new insights into the structural design of Si-based electrodes.
基金supported by the National Natural Science Foun-dation of China(Grant No.U2167214).
文摘Due to excellent thermal insulation performance at room temperature and ultralow density,silica aero-gels are candidates for thermal insulation.However,at high temperatures,the thermal insulation prop-erty of silica aerogels decreased greatly caused by transparency to heat radiation.Opacifiers introduced into silica sol can block heat radiation yet destroy the uniformity of aerogels.Herein,we designed and prepared a silica aerogel composite with oriented and layered silica fibers(SFs),SiC nanowires(SiC_(NWs)),and silica aerogels,which were prepared by papermaking,chemical vapor infiltration(CVI),and sol-gel respectively.Firstly,oriented and layered SFs made still air a wall to block heat transfer by the solid phase.Secondly,SiC_(NWs) were grown in situ on the surface of SFs evenly to weave into the network,and the network reduced the gaseous thermal conductivity by dividing cracks in SFs/SiC_(NWs)/SA.Thirdly,SiC_(NWs) weakened the heat transfer by radiation at high temperatures.Therefore,SFs/SiC_(NWs)/SA presented remarkable thermal insulation(0.017 W(m K)^(-1) at 25℃,0.0287 W(m K)^(-1) at 500℃,and 0.094 W(m K)^(-1) at 1000℃).Besides,SFs/SiC_(NWs)/SA exhibited remarkable thermal stability(no size transform after being heat treated at 1000℃ for 1800 s)and tensile strength(0.75 MPa).These integrated properties made SFs/SiC_(NWs)/SA a promising candidate for highly efficient thermal insulators.
基金Project supported by the National Natural Science Foundation of China(Nos.12202039,52204085,and 52474123)。
文摘This paper theoretically investigates the influence of a cylindrical PN junction on the propagation characteristics of shear cylindrical waves(SCWs)in an infinitely long piezoelectric semiconductor(PS)concentric cylinder structure.This PS concentric cylinder structure is composed of three regions:an inner PS cylinder,an outer PS cylindrical shell,and a cylindrical PN junction at the interface between the two aforementioned regions.First,the basic equations of the PS concentric cylinder structure are derived,taking into account the coupling of the mechanical displacement,electric potential,and charge carrier perturbation in the cylindrical coordinate system.Next,a mathematical model for the SCWs in this PS concentric cylinder structure is established,utilizing the spectral method and considering the physical characteristics of the cylindrical PN junction.Finally,the dispersion and attenuation curves of the SCWs are numerically calculated to discuss the influence of the interface effect resulting from the cylindrical PN junction.It is found that the existence of a cylindrical PN junction can either reduce or enhance the mechanical-to-electrical energy conversion,which is closely related to the doping mode,doping concentration,and curvature radius of the cylindrical interface.A reasonable design of the aforementioned parameters can optimize the wave motion in acoustic equipment formed by PS media with different frequencies or wavelengths.The construction and resolution of the mathematical model as well as the analysis of physical mechanisms can offer theoretical guidance for improving the efficiency of energy conversion from mechanical energy to electrical energy and optimizing the acoustic performance of energy harvesting devices.
文摘Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.
文摘The present paper presents an innovative approach for the numerical modeling of piezo-electric transducers for the health-monitoring of layered structures.The numerical approach has been developed in the frameworks of the Carrera Unified Formulation.This computa-tional tool allows refined numerical models to be derived in a unified and efficient fashion.The use of higher-order models and the cap-ability to connect different kinematic models using the node-depen-dent kinematic approach has led to an efficient modeling technique for global-local analysis.This approach can refine the model only in those regions where it is required,e.g.,the areas where piezo-electric transducers are placed.The model has been used to study embedded and surface-mounted sensors.The accuracy of the pre-sent model has been verified by comparing the current results with numerical and experimental data from the literature.Different mod-eling solutions have been developed,mixing one-,two-and threedimensional finite elements.The results show that the use of the present modeling technique allows the computational cost to be reduced with respect to the classical approaches preserving the ccuracy of the results in the critical areas.
基金The project supported by National Natural Science Foundation of China (10632020, 10672017 and 20451057)
文摘Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are considered. The transfer matrices between two consecutive unit cells are obtained according to the continuity conditions. The expressions of localization factor and localization length in the disordered periodic structures are presented. For the disordered periodic piezoelectric structures, the numerical results of localization factor and localization length are presented and discussed. It can be seen from the results that the frequency passbands and stopbands appear for the ordered periodic structures and the wave localization phenomenon occurs in the disordered periodic ones, and the larger the coefficient of variation is, the greater the degree of wave localization is. The widths of stopbands in the ordered periodic structures are very narrow when the properties of the consecutive piezoelectric materials are similar and the intervals of stopbands become broader when a certain material parameter has large changes. For the wave propagating in the direction normal to the layers the localization length has less dependence on the frequency, but for the wave propagating in the direction tangential to the layers the localization length is strongly dependent on the frequency.
基金Project supported by the National Natural Science Foundation of China(Nos.10132010 and 10072033)
文摘The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effects of the initial stresses on the phase velocity and theelectromechanical coupling coefficient for the fundamental mode of the layered piezoelectricstructures are discussed. Numerical results for the c-axis oriented film of LiNbO_3 on a sapphiresubstrate are given. It is found that the fractional change in phase velocity is a linear functionwith the initial stresses, and the electromechanical coupling factor increases with an increase ofthe absolute values of the compressive initial stresses. The results are useful for the design ofsurface acoustic wave devices.
基金supported by a grant from the Subway Fine Dust Reduction Technology Development Project of the Ministry of Land Infrastructure and Transport,Republic of Korea(21QPPWB152306-03)the Basic Science Research Capacity Enhancement Project through a Korea Basic Science Institute(National Research Facilities and Equipment Center)grant funded by the Ministry of Education of the Republic of Korea(2019R1A6C1010016)。
文摘Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devices(PEDs),etc.In recent decades,Lithium-ion batteries(LIBs) have been extensively utilized in largescale energy storage devices owing to their long cycle life and high energy density.However,the high cost and limited availability of Li are the two main obstacles for LIBs.In this regard,sodium-ion batteries(SIBs) are attractive alternatives to LIBs for large-scale energy storage systems because of the abundance and low cost of sodium materials.Cathode is one of the most important components in the battery,which limits cost and performance of a battery.Among the classified cathode structures,layered structure materials have attracted attention because of their high ionic conductivity,fast diffusion rate,and high specific capacity.Here,we present a comprehensive review of the classification of layered structures and the preparation of layered materials.Furthermore,the review article discusses extensively about the issues of the layered materials,namely(1) electrochemical degradation,(2) irreversible structural changes,and(3) structural instability,and also it provides strategies to overcome the issues such as elemental phase composition,a small amount of elemental doping,structural design,and surface alteration for emerging SIBs.In addition,the article discusses about the recent research development on layered unary,binary,ternary,quaternary,quinary,and senary-based O3-and P2-type cathode materials for high-energy SIBs.This review article provides useful information for the development of high-energy layered sodium transition metal oxide P2 and O3-cathode materials for practical SIBs.
基金supported by the Guangdong Basic and Applied Basic Research Foundation (2020B1515120013,2022B1515120066)National Natural Science Foundation of China (Nos.U2001218, 51875215)+1 种基金Key-Area Research and Development Program of Guangdong Province (2020B090923001)Special Support Foundation of Guangdong Province (No.2019TQ05Z110)。
文摘It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites including those inspired by gradient layered materials.In this work,we used LPBF to selectively prepare Ti N/Ti gradient layered structure(GLSTi)composites by using different N_(2)–Ar ratios during the LPBF process.We systematically investigated the mechanisms of in-situ synthesis Ti N,high strength and ductility of GLSTi composites using microscopic analysis,TEM characterization,and tensile testing with digital image correlation.Besides,a digital correspondence was established between the N_(2) concentration and the volume fraction of LPBF in-situ synthesized Ti N.Our results show that the GLSTi composites exhibit superior mechanical properties compared to pure titanium fabricated by LPBF under pure Ar.Specifically,the tensile strength of GLSTi was more than 1.5times higher than that of LPBF-formed pure titanium,reaching up to 1100 MPa,while maintaining a high elongation at fracture of 17%.GLSTi breaks the bottleneck of high strength but low ductility exhibited by conventional nanoceramic particle-strengthened titanium matrix composites,and the hetero-deformation induced strengthening effect formed by the Ti N/Ti layered structure explained its strength-plasticity balanced principle.The microhardness exhibits a jagged variation of the relatively low hardness of 245 HV0.2 for the pure titanium layer and a high hardness of 408 HV0.2 for the N_(2) in-situ synthesis layer.Our study provides a new concept for the structure-performance digital customization of 3D-printed Ti-based composites.
文摘In this study,we performed first-principles calculations using the VASP(Vienna Ab initio Simulation)software package to investigate the crystal structure,electronic structure,and optical properties of a new layered ternary metal chalcogenide,Eu_(2)InTe_(5).Our results show that Eu_(2)InTe_(5) is a non-zero-gap metal with a layered structure characterized by strong intra-layer atomic bonding and weak inter-layer interaction,which suggests its potential application as a nanomaterial.We also studied the optical properties,including the absorption coefficient,imaginary and real parts of the complex dielectric constant,and found that Eu_(2)InTe_(5) exhibits strong photoresponse characteristics at the junction of ultraviolet and visible light as well as blue-green light,with peaks at wavelengths of 389 nm and 477 nm.This suggests that it could be used in the development of UV(ultraviolet)detectors and other optoelectronic devices.Furthermore,due to its strong absorption,low loss,and low reflectivity,Eu_(2)InTe_(5) has the potential to be used as a promising photovoltaic absorption layer in solar cells.
基金the financial supports of Fundamental Research Funds for the Central Universities,China(Nos.YWF-23-L-1012,YWF-22-L-1017)。
文摘The limited metal-polymer interlaminar property is a significant obstacle to the advancement of Ti/Carbon Fiber(CF)/Polyether Ether Ketone(PEEK)hybrid laminates.We report for the first time a novel method by utilizing the mussel-inspired Polydopamine(PDA)to introduce a strong chemical-physical bonding between titanium and PEEK.The enhanced Fiber-Metal Laminate(FML)exhibits a significant 48.82%enhancement in Interlaminar Shear Strength(ILSS).In addition,it alters the failure mode of the FML from single metal-resin interlaminar delamination to a multi-mechanism,including debonding,delamination of different composite layers,leading to a 28.57%improvement in maximum displacement.
基金supported by the National Key R&D Program of China(Grant Nos.2024YFB3714502,2024YFB3714501,2024YFB3714504)the National Natural Science Foundation of China(Grant Nos.52130204,52174376)+5 种基金the TQ Innovation Foundation(Grant No.23-TQ09-02-ZT-01-005)the Aeronautical Science Foundation of China(Grant No.20220042053001)the Ningbo Science and Technology Plan Project(Grant No.2025Z070)the Key R&D Project of Shaanxi Province(Grant Nos2024GX-YBXM-220,2024CY-GJHX-29,2024GX-ZDCYL-03-03,2024GX-YBXM-400)the National Advanced Rare Metal Materials Innovation Center Project[Grant No.2024 ZG-GCZX-01(1)-01]the Foundation of China Scholarship Council(Grant No.202406290136)。
文摘To meet the evolving demands of aeroengine development,the structural and performance requirements for ceramic cores have become increasingly stringent.Vat photopolymerization 3D printing,owing to its moldless,fiexible manufacturing,and other advantages,demonstrates significant potential in the preparation of ceramic cores with intricate structures.However,its practical application still faces multiple challenges,including layered structures and property anisotropy,defects such as cracks and collapse during printing and sintering,forming inaccuracies,and difficulties in controlling surface roughness.Recent advances have focused on optimizing slurry formulation and rheology,improving curing behavior,introducing auxiliary powders and additives,tailoring forming parameters,and optimizing the sintering process.Nevertheless,effectively suppressing lamellar defects,achieving superior dimensional accuracy,and maintaining high surface quality in complex structures remain the core scientific and technical issues to be solved.Future research should concentrate on refining curing mechanisms,advancing powder design and organic system optimization,and regulating the coupled processes of forming,debinding,and sintering to accelerate the application of VPP 3D printed ceramic cores in aerospace manufacturing.
基金Project(50721003)supported by the National Natural Science Foundation of ChinaProject(07JJ6082)supported by the Natural Science Foundation of Hunan Province,ChinaProject supported by the Open Project of State Key Laboratory of Powder Metallurgy in Central South University,China
文摘Layered Li[Ni1/3Co1/3Mn1/3]O2 was synthesized with complex metal hydroxide precursors that were prepared by a co-precipitation method.The influence of coordination between ammonia and transition-metal cations on the structural and electrochemical properties of the Li[Ni1/3Co1/3Mn1/3]O2 materials was studied.It is found that when the molar ratio of ammonia to total transition-metal cations is 2.7：1,uniform particle size distribution of the complex metal hydroxide is observed via scanning electron microscopy.The average particle size of Li[Ni1/3Co1/3Mn1/3]O2 materials was measured to be about 500 nm,and the tap-density was measured to be approximately 2.37 g/cm3,which is comparable with that of commercialized LiCoO2.XRD analysis indicates that the presently synthesized Li[Ni1/3Co1/3Mn1/3]O2 has a hexagonal layered-structure.The initial discharge capacity of the Li[Ni1/3Co1/3Mn1/3]O2 positive-electrode material is determined to be 181.5 mA·h/g using a Li/Li[Ni1/3Co1/3Mn1/3]O2 cell operated at 0.1C in the voltage range of 2.8-4.5 V.The discharge capacity at the 50th cycle at 0.5C is 170.6 mA·h/g.
基金supported by the National Key Research and Development Program of China(Grant No.2021YFB3501002)the National Natural Science Foundation of China(Grant No.52301059,No.52271009)the Shanghai Post-doctoral Excellence Program(Grant No.2023372).
文摘Magnesium and its alloys offer lightweight advantage and have extensive development prospects,particularly in aerospace.However,their flammability poses a significant barrier on the development of Mg alloys.The ignition resistance of these alloys often depends on the protectiveness of the oxide film formed on the surface.This paper elucidates the formation mechanism of oxide film from thermodynamics and kinetics,classifying oxide films based on their layered structure to assess their protective properties.Furthermore,it comprehensively reviews the impact of characteristics on the protective effectiveness such as compactness,continuity,thickness,and mechanical properties.The paper also introduces various characterization methods for the microstructure and properties of oxide film.The primary objective of this paper is to enhance the comprehension of oxide film concerning the ignition resistance of Mg alloys and to furnish references for future advancements and research in Mg alloys with heightened ignition resistance.
