Large-scale 3D physical models of complex structures can be used to simulate hydrocarbon exploration areas. The high-fidelity simulation of actual structures poses challenges to model building and quality control. Suc...Large-scale 3D physical models of complex structures can be used to simulate hydrocarbon exploration areas. The high-fidelity simulation of actual structures poses challenges to model building and quality control. Such models can be used to collect wideazimuth, multi-azimuth, and full-azimuth seismic data that can be used to verify various 3D processing and interpretation methods. Faced with nonideal imaging problems owing to the extensive complex surface conditions and subsurface structures in the oil-rich foreland basins of western China, we designed and built the KS physical model based on the complex subsurface structure. This is the largest and most complex 3D physical model built to date. The physical modeling technology advancements mainly involve 1） the model design method, 2） the model casting flow, and 3） data acquisition. A 3D velocity model of the physical model was obtained for the first time, and the model building precision was quantitatively analyzed. The absolute error was less than 3 mm, which satisfies the experimental requirements. The 3D velocity model obtained from 3D measurements of the model layers is the basis for testing various imaging methods. Furthermore, the model is considered a standard in seismic physical modeling technology.展开更多
The excavation of deep tunnels crossing faults is highly prone to triggering rockburst disasters,which has become a significant engineering issue.In this study,taking the fault-slip rockbursts from a deep tunnel in so...The excavation of deep tunnels crossing faults is highly prone to triggering rockburst disasters,which has become a significant engineering issue.In this study,taking the fault-slip rockbursts from a deep tunnel in southwestern China as the engineering prototype,large-scale three-dimensional(3D)physical model tests were conducted on a 3D-printed complex geological model containing two faults.Based on the selfdeveloped 3D loading system and excavation device,the macroscopic failure of fault-slip rockbursts was simulated indoors.The stress,strain,and fracturing characteristics of the surrounding rock near the two faults were systematically evaluated during excavation and multistage loading.The test results effectively revealed the evolution and triggering mechanism of fault-slip rockbursts.After the excavation of a highstress tunnel,stress readjustment occurred.Owing to the presence of these two faults,stress continued to accumulate in the rock mass between them,leading to the accumulation of fractures.When the shear stress on a fault surface exceeded its shear strength,sudden fault slip and dislocation occurred,thus triggering rockbursts.Rockbursts occurred twice in the vault between the two faults,showing obvious intermittent characteristics.The rockburst pit was controlled by two faults.When the faults remained stable,tensile failure predominated in the surrounding rock.However,when the fault slip was triggered,shear failure in the surrounding rock increased.These findings provide valuable insights for enhancing the comprehension of fault-slip rockbursts.展开更多
Thermal Protection System(TPS)with thick tiles,low thermal conductivity,and a short re-entry stage stands as a critical element within reusable aircraft,whose reliability is related to the function and changes with th...Thermal Protection System(TPS)with thick tiles,low thermal conductivity,and a short re-entry stage stands as a critical element within reusable aircraft,whose reliability is related to the function and changes with their physical properties,external conditions,and degradation.Meanwhile,due to the limitation of testing resources,epistemic uncertainties stemming from the small samples are present in TPS reliability modeling.However,current TPS reliability modeling methods face challenges in characterizing the relationships among reliability and physical properties,external conditions,degradation,and epistemic uncertainties.Therefore,under the framework of belief reliability theory,a TPS reliability model is constructed,which takes into account the physical principle,external conditions,performance degradation,and epistemic uncertainties.A reliability simulation algorithm is proposed to calculate TPS reliability.Through a case study and comparison analysis,the proposed method is validated as more effective than the existing method.Additionally,reliability sensitivity analysis is conducted to identify the sensitive factors of reliability under the condition of small samples,through which suggestions are provided for TPS functional design and improvement.展开更多
Research on scale effects on flows over weirs has been conducted on a limited basis, primarily focusing on flows upstream of a single-type weir, such as ogee, broad-crested, and sharp-crested (linear and non-linear) w...Research on scale effects on flows over weirs has been conducted on a limited basis, primarily focusing on flows upstream of a single-type weir, such as ogee, broad-crested, and sharp-crested (linear and non-linear) weirs. However, the scale effects downstream of these single-type weirs have not been thoroughly investigated. This study examined the scale effects on flows over a combined weir system consisting of an ogee weir and a sharp-crested weir, both upstream and downstream, utilizing physical modeling at a 1:33.33 scale based on Froude similarity and three-dimensional (3D) computational fluid dynamics (CFD) modeling. The sharp-crested weir in this study was represented by two sluice gates that remain closed and submerged during flood events. The experimental data confirmed that the equivalent discharge coefficients of the combined weir system behaved similarly to those of a sharp-crested weir across various H/P (where H is the total head, and P is the weir height) values. However, scale effects on the discharge rating curve due to surface tension and viscosity could only be minimized when H/P > 0.4, Re > 26 959, and We > 240 (where Re and We are the Reynolds and Weber numbers, respectively), provided that the water depth exceeded 0.042 m above the crest. Additionally, Re greater than 4 × 104 was necessary to minimize scale effects caused by viscosity in flows in the spillway channel and stilling basin (with baffle blocks). The limiting criteria aligned closely with existing literature. This study offers valuable insights for practical applications in hydraulic engineering in the future.展开更多
Structure-type rockbursts frequently occur in deep tunnels,with structural planes and stress conditions being critical factors in their formation.In this study,we utilized specially developed analogous materials that ...Structure-type rockbursts frequently occur in deep tunnels,with structural planes and stress conditions being critical factors in their formation.In this study,we utilized specially developed analogous materials that exhibit the high brittleness and strength characteristics of deep hard rock to construct physical models representing different types of structural planes,including composite,exposed,non-exposed,and throughgoing structural planes.Physical simulation experiments were conducted on structuretype rockbursts in deep horseshoe-shaped tunnels,focusing on strain differentiation characteristics,critical triggering conditions,critical crack opening displacement,the incubation process,the reduction effects of structural planes on failure intensity,and formation mechanisms.These experiments were complemented by acoustic and optical monitoring,as well as discrete element numerical simulations,to provide a comprehensive analysis.The results revealed that the most significant strain heterogeneity in the surrounding rock occurs at the tip of the structural plane along the tunnel's minimum principal stress direction,driven by the combined effects of tensile and shear forces.We quantitatively determined the critical stress and strain conditions for structure-type rockbursts and evaluated the intensity of rockbursts induced by different structural planes using critical crack opening displacement(COD)values,the uniformity coefficient,and the curvature coefficient.Analysis of acoustic emission events,including frequency,amplitude,and b-value,indicated that the macro-fracture process is governed by both the principal stress differential and the characteristics of the structural plane.Furthermore,using the bearing capacity reduction coefficient,we found that exposed structural planes have the most significant weakening effect on rock mass strength,followed by non-exposed and throughgoing structural planes.The analysis of average frequency(AF)and rise angle(RA)parameters revealed a close correlation between the failure modes of structure-type rockbursts,the rock mass structure,and the stress levels.These findings provide critical theoretical support for the prediction and prevention of structure-type rockburst disasters.展开更多
A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of ...A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of shielding gases with varying He-Ar ratios,and the coupling between arc plasma and laser-induced metal plume.The accuracy of the model is validated using a high-speed camera.The effects of varying He contents in the shielding gas on both the temperature and flow velocity of hybrid plasma,as well as the distribu-tion of laser-induced metal vapor mass,were investigated separately.The maximum temperature and size of arc plasma decrease as the He volume ratio increases,the arc distribution becomes more concentrated,and its flow velocity initially decreases and then sharply increases.At high helium content,both the flow velocity of hybrid plasma and metal vapor are high,the metal vapor is con-centrated on the right side of keyhole,and its flow appears chaotic.The flow state of arc plasma is most stable when the shielding gas consists of 50%He+50%Ar.展开更多
A complex geological environment with faults can be encountered in the process of coal mining.Fault activation can cause instantaneous structure slipping,releasing a significant amount of elastic strain energy during ...A complex geological environment with faults can be encountered in the process of coal mining.Fault activation can cause instantaneous structure slipping,releasing a significant amount of elastic strain energy during underground coal mining.This would trigger strong rockburst disasters.To understand the occurrence of fault-slip induced rockbursts,we developed a physical model test system for fault-slip induced rockbursts in coal mine drifts.The boundary energy storage(BES)loading apparatus and bottom rapid retraction(BRR)apparatus are designed to realize energy compensation and continuous boundary stress transfer of the surrounding rocks for instantaneous fault slip,as well as to provide space for the potential fault slip.Taking the typical fault-slip induced rockburst in the Xinjulong Coal Mine,China,as the background,we conducted a model test using the test system.The deformation and stress in the rock surrounding the drift and the support unit force during fault slip are analyzed.The deformation and failure characteristics and dynamic responses of drifts under fault-slip induced rockbursts are obtained.The test results illustrate the rationality and effectiveness of the test system.Finally,corresponding recommendations and prospects are proposed based on our findings.展开更多
Following the fundamental characteristics of the porosity windbreak,this study suggests a new numerical investigation method for the wind field of the windbreak based on the porous medium physical model.This method ca...Following the fundamental characteristics of the porosity windbreak,this study suggests a new numerical investigation method for the wind field of the windbreak based on the porous medium physical model.This method can transform the reasonable matching problem of the porosity and windproof performance of the windbreak into a study of the relationship between the resistance coefficient of the porous medium and the aerodynamic load of the train.This study examines the influence of the hole type on the wind field behind the porosity windbreak.Then,the relationship between the resistance coefficient of the porous medium,the porosity of the windbreak,and the aerodynamic loads of the train is investigated.The results show that the porous media physical model can be used instead of the windbreak geometry to study the windbreak-train aerodynamic performance,and the process of using this method is suggested.展开更多
Triangle zones, generally found in foreland fold-and-thrust belts, serve as favorable objects of petroleum exploration. Taking the Dabashan foreland belt as an example, we studied the formation and development of tria...Triangle zones, generally found in foreland fold-and-thrust belts, serve as favorable objects of petroleum exploration. Taking the Dabashan foreland belt as an example, we studied the formation and development of triangle zones, and investigated the effect of d^collements and the mechanical contrast of lithology by employing the method of physical modeling. Four experimental models were conducted in the work. The results showed that ＇sand wedges＇ grew episodically, recorded by deformational length, height and slope angle. The height versus shortening rate presented an S-shape curve, and uplifting occurred successively in the direction of the foreland belt. During the formation of the triangle zone, layer-parallel shortening took place at the outset; deformation decoupling then occurred between the upper and lower brittle layers, divided by a middle-embedded silicone polymers layer. The upper brittle layers deformed mainly by folding, while the lower sand layers by thrusting. As shortening continued, the geometry of a triangle zone was altered. We consider that the triangle zone in the Dabashan foreland belt was modified from an early one based on available seismic profiles and the experimental results. In addition, dccollements and mechanical contrast impose significant influence on structural development, which can directly give rise to structural discrepancies. More d^collements and obvious mechanical contrast between brittle layers can promote the coupling between the upper and lower brittle layers. Basal d^collement controls the whole deformation and decreases the slope angle of the wedge, while roof d^collement determines whether a triangle zone can be formed.展开更多
As a critical material in construction engineering,concrete requires accurate prediction of its outlet temperature to ensure structural quality and enhance construction efficiency.This study proposes a novel hybrid pr...As a critical material in construction engineering,concrete requires accurate prediction of its outlet temperature to ensure structural quality and enhance construction efficiency.This study proposes a novel hybrid prediction method that integrates a heat conduction physical model with a multilayer perceptron(MLP)neural network,dynamically fused via a weighted strategy to achieve high-precision temperature estimation.Experimental results on an independent test set demonstrated the superior performance of the fused model,with a root mean square error(RMSE)of 1.59℃ and a mean absolute error(MAE)of 1.23℃,representing a 25.3%RMSE reduction compared to conventional physical models.Ambient temperature and coarse aggregate temperature were identified as the most influential variables.Furthermore,the model-based temperature control strategy reduced costs by 0.81 CNY/m^(3),showing significant potential for improving resource efficiency and supporting sustainable construction practices.展开更多
In order to capture the mechanism of roadway instability in deep mines, a new approach of Physically Finite Elemental Slab Assemblage (PFESA) is proposed in order to construct a large-scale physical model simulating t...In order to capture the mechanism of roadway instability in deep mines, a new approach of Physically Finite Elemental Slab Assemblage (PFESA) is proposed in order to construct a large-scale physical model simulating the geologically horizontal strata. We carried out physical modeling on the deformation and failure processes of roadways subjected to a plane loading scheme. Our laboratory tests were based on work which incorporated infrared (IR) detection, IR radiation temperature (IRT) statistics, image feature extraction and 2D Fourier transformation, from resulting thermographies. The IRT characterizes the mechanical responses from the roadway after loading with two stages, i.e., IRT evolving at higher levels corresponded to shallow mining (≤500 m) during which the roadway deformed gradually (referred to as the "steady deformation stage"); IRT evolving in a quasi-cyclical manner with multiple peaks corresponded to deep mining (800–2600 m), in which the failure mode for the roadway are dominated by breakage and collapse (called the "unsteady deformation stage"). The IR images and 2D Fourier spectra illustrate detailed information in terms of initiation, nucleation and coalescence of the damage to rock masses and the eventual failure of roadways subject to external loading.展开更多
In 2018,a catastrophic high-altitude landslide occurred at Baige,located within the tectonic suture zone of the Upper Jinsha River.The failure mechanism of this event remains poorly understood.This study aims to eluci...In 2018,a catastrophic high-altitude landslide occurred at Baige,located within the tectonic suture zone of the Upper Jinsha River.The failure mechanism of this event remains poorly understood.This study aims to elucidate the deformation characteristics and failure mechanism of the Baige landslide by employing a comprehensive methodology,including field geological surveys,analysis of historical remote sensing imagery,high-density electrical resistivity surveys,and advanced displacement monitoring.Additionally,the physical modeling experiments were conducted to replicate the unique failure modes.The findings propose a novel perspective on the failure mechanism of the Baige landslide,which involves two critical stages:first,the brittle shear zone bypasses and fails at the lower locked segment,and second,the failure of the upper locked segment,combined with the shear zone's impact on the lower locked segment,triggers overall slope instability.Physical modeling experiments revealed a transition from initial acceleration to a rapid acceleration phase,particularly marked by a significant increase in velocity following the failure of the upper locked segment.The intensity of acoustic emission signals was found to correlate with the failure of the locked segments and the state of particle collisions post-failure.It offers new insights into the failure mechanisms of tectonic mélange belt large-scale landslides in suture zones,contributing to the broader field of landslide research.展开更多
During actual high-speed flights,the electromagnetic(EM)properties of aircraft radomes are influenced by dielectric temperature drift,leading to substantial drift in the boresight errors(BSEs)from their room temperatu...During actual high-speed flights,the electromagnetic(EM)properties of aircraft radomes are influenced by dielectric temperature drift,leading to substantial drift in the boresight errors(BSEs)from their room temperature values.However,applying thermal loads to the radome during ground-based EM simulation tests is challenging.This paper presents an EM equivalent physical model(EEPM)for high-speed aircraft radomes that account for the effects of dielectric temperature drift.This is achieved by attaching dielectric slices of specific thicknesses to the outer surface of a room-temperature radome(RTR)to simulate the increase in electrical thickness resulting from high temperatures.This approach enables accurate simulations of the BSEs of high-temperature radomes(HTRs)under high-speed flight conditions.An application example,supported by full-wave numerical calculations and physical testing,demonstrates that the EEPM exhibits substantial improvement in approximating the HTR compared to the RTR,facilitating precise simulations of the BSEs of HTRs during high-speed flights.Overall,the proposed EEPM is anticipated to considerably enhance the alignment between the ground-based simulations of high-speed aircraft guidance systems and their actual flight conditions.展开更多
High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slop...High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slope angle was successfully implemented at the northwest wall between Nos. 4 and 5 exploration lines of Shuichang Iron Mine, taking into account the 3D scale effect. The phys-ico-mechanical properties of rock materials were obtained by laboratory tests conducted on sample cores from exploration drilling directly from the iron mine. A porous rock-like composite material was formed for the model, and the mechanical parameters of the material were assessed experimentally;specifically, the effect of water on the sample was quantitatively determined. We adopted an experimental setup using stiff modular applied static loading to carry out a visual excavation of the slope at a random depth. The setup was equipped with acous-tic emission （AE） sensors, and the experiments were monitored by crack optical acquirement, ground penetrating radar, and close-field pho-togrammetry to investigate the mechanisms of rock-mass destabilization in the high-steep slope. For the complex study area, the model re-sults indicated a clear correlation between the model＇s destabilization resulting from slope excavation and the collected monitoring informa-tion. During the model simulation, the overall angle of the slope increased by 1-6 degrees in different sections. Dramatically, the modeled excavation scheme saved over 80 million tons of rock from extraction, generating enormous economic and ecological benefits.展开更多
The evolution of mining-induced stress field in longwall panel is closely related to the fracture field and the breaking characteristics of strata.Few laboratory experiments have been conducted to investigate the stre...The evolution of mining-induced stress field in longwall panel is closely related to the fracture field and the breaking characteristics of strata.Few laboratory experiments have been conducted to investigate the stress field.This study investigated its evolution by constructing a large-scale physical model according to the in situ conditions of the longwall panel.Theoretical analysis was used to reveal the mechanism of stress distribution in the overburden.The modelling results showed that:(1)The major principal stress field is arch-shaped,and the strata overlying both the solid zones and gob constitute a series of coordinated load-bearing structures.The stress increasing zone is like a macro stress arch.High stress is especially concentrated on both shoulders of the arch-shaped structure.The stress concentration of the solid zone in front of the gob is higher than the rear solid zone.(2)The characteristics of the vertical stress field in different regions are significantly different.Stress decreases in the zone above the gob and increases in solid zones on both sides of it.The mechanical analysis show that for a given stratum,the trajectories of principal stress are arch-shaped or inverselyarched,referred to as the‘‘principal stress arch’’,irrespective of its initial breaking or periodic breaking,and determines the fracture morphology.That is,the trajectories of tensile principal stress are inversely arched before the first breaking of the strata,and cause the breaking lines to resemble an inverted funnel.In case of periodic breaking,the breaking line forms an obtuse angle with the advancing direction of the panel.Good agreement was obtained between the results of physical modeling and the theoretical analysis.展开更多
The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhan...The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.展开更多
Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scen...Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scene is presented. We first propose a Two-Fluid model based on the physical theory of tornado, then we simulate the flow of tornado and its interaction with surrounding objects such as debris, etc. Taking the scattering and absorption of light by the participating media into account, the illumination effects of the tornado scene can be generated realistically. With the support of graphics hardware, various kinds of dynamic tornado scenes can be rendered at interactive rates.展开更多
Non-obstacle design is critical to tailor physically handicapped workers in manufacturing system.Simultaneous consideration of variability in physically disabled users,machines and environment of the manufacturing sys...Non-obstacle design is critical to tailor physically handicapped workers in manufacturing system.Simultaneous consideration of variability in physically disabled users,machines and environment of the manufacturing system is extremely complex and generally requires modeling of physically handicapped interaction with the system.Most current modeling either concentrates on the task results or functional disability.The integration of physical constraints with task constraints is far more complex because of functional disability and its extended influence on adjacent body parts.A framework is proposed to integrate the two constraints and thus model the specific behavior of the physical handicapped in virtual environment generated by product specifications.Within the framework a simplified model of physical disabled body is constructed,and body motion is generated based on 3 levels of constraints(effecter constraints,kinematics constraints and physical constraints).The kinematics and dynamic calculations are made and optimized based on the weighting manipulated by the kinematics constraints and dynamic constraints.With object transferring task as example,the model is validated in Jack 6.0.Modelled task motion elements except for squatting and overreaching well matched with captured motion elements.The proposed modeling method can model the complex behavior of the physically handicapped by integrating both task and physical disability constraints.展开更多
This paper introduces the seismic physical modeling technology in the CNPC Key Lab of Geophysical Exploration. It includes the seismic physical model positioning system, the data acquisition system, sources, transduce...This paper introduces the seismic physical modeling technology in the CNPC Key Lab of Geophysical Exploration. It includes the seismic physical model positioning system, the data acquisition system, sources, transducers, model materials, model building techniques, precision measurements of model geometry, the basic principles of the seismic physical modeling and experimental methods, and two physical model examples.展开更多
In order to examine the effectiveness of engineering protection against localized scour in front of the south groin-group of the Yangtze Estuary Waterway Improvement Project, Phase I , an undistort-ed physical model o...In order to examine the effectiveness of engineering protection against localized scour in front of the south groin-group of the Yangtze Estuary Waterway Improvement Project, Phase I , an undistort-ed physical model on a geometric scale of 1:250 is built in this study, covering two groins and their adacent estuarine areas. By use of rinsing fix-bed model as well as localized mobile-bed model, the experiment is undertaken under bi-directional steady flow. According to the experimental results, waterway dredging leads to the increase in steram velocity, the increase being larger during the ebb than during the flood. Construction of the upstream groin has some influence on the flow patterns near the downstream groin. Localized scour in front of the groin-heads is controlled mainly by ebb flow. In the case of a riverbed composed entirely of silt, the depths of localized scour in front of the two groin- heads are 27 m and 29 m, respectively. In reality, the underneath sediment of the prototype riverbed is clay whose threshold velocity is much higher than the stream velocity in the Yangtze Estuary; therefore, the depths of localized scour will not be much larger than the thickness of the silt layer, i. e. 7.4 m and 4.7 m, respectively. The designed aprons covering the riverbed in fron of the groin-heads are very effective in scour control. Aprons of slightly smaller size can also fulfill the task of protection, but the area of localized scour increases significantly.展开更多
基金sponsored by National Science and Technology Major Project(2011ZX05046-001)
文摘Large-scale 3D physical models of complex structures can be used to simulate hydrocarbon exploration areas. The high-fidelity simulation of actual structures poses challenges to model building and quality control. Such models can be used to collect wideazimuth, multi-azimuth, and full-azimuth seismic data that can be used to verify various 3D processing and interpretation methods. Faced with nonideal imaging problems owing to the extensive complex surface conditions and subsurface structures in the oil-rich foreland basins of western China, we designed and built the KS physical model based on the complex subsurface structure. This is the largest and most complex 3D physical model built to date. The physical modeling technology advancements mainly involve 1） the model design method, 2） the model casting flow, and 3） data acquisition. A 3D velocity model of the physical model was obtained for the first time, and the model building precision was quantitatively analyzed. The absolute error was less than 3 mm, which satisfies the experimental requirements. The 3D velocity model obtained from 3D measurements of the model layers is the basis for testing various imaging methods. Furthermore, the model is considered a standard in seismic physical modeling technology.
基金funding support from the National Natural Science Foundation of China(Grant Nos.42177136 and 52309126).
文摘The excavation of deep tunnels crossing faults is highly prone to triggering rockburst disasters,which has become a significant engineering issue.In this study,taking the fault-slip rockbursts from a deep tunnel in southwestern China as the engineering prototype,large-scale three-dimensional(3D)physical model tests were conducted on a 3D-printed complex geological model containing two faults.Based on the selfdeveloped 3D loading system and excavation device,the macroscopic failure of fault-slip rockbursts was simulated indoors.The stress,strain,and fracturing characteristics of the surrounding rock near the two faults were systematically evaluated during excavation and multistage loading.The test results effectively revealed the evolution and triggering mechanism of fault-slip rockbursts.After the excavation of a highstress tunnel,stress readjustment occurred.Owing to the presence of these two faults,stress continued to accumulate in the rock mass between them,leading to the accumulation of fractures.When the shear stress on a fault surface exceeded its shear strength,sudden fault slip and dislocation occurred,thus triggering rockbursts.Rockbursts occurred twice in the vault between the two faults,showing obvious intermittent characteristics.The rockburst pit was controlled by two faults.When the faults remained stable,tensile failure predominated in the surrounding rock.However,when the fault slip was triggered,shear failure in the surrounding rock increased.These findings provide valuable insights for enhancing the comprehension of fault-slip rockbursts.
基金supported by the steady supports scientific research of Key Laboratory of Defense Science and Technology,China(No.WDZC20220105)the National Natural Science Foundation of China(Nos.51775020,62073009,U20B2002)the Science Challenge Project,China(No.TZ2018007)。
文摘Thermal Protection System(TPS)with thick tiles,low thermal conductivity,and a short re-entry stage stands as a critical element within reusable aircraft,whose reliability is related to the function and changes with their physical properties,external conditions,and degradation.Meanwhile,due to the limitation of testing resources,epistemic uncertainties stemming from the small samples are present in TPS reliability modeling.However,current TPS reliability modeling methods face challenges in characterizing the relationships among reliability and physical properties,external conditions,degradation,and epistemic uncertainties.Therefore,under the framework of belief reliability theory,a TPS reliability model is constructed,which takes into account the physical principle,external conditions,performance degradation,and epistemic uncertainties.A reliability simulation algorithm is proposed to calculate TPS reliability.Through a case study and comparison analysis,the proposed method is validated as more effective than the existing method.Additionally,reliability sensitivity analysis is conducted to identify the sensitive factors of reliability under the condition of small samples,through which suggestions are provided for TPS functional design and improvement.
基金supported by the Ministry of Public Works and Housing of Indonesia and Parahyangan Catholic University(Grant No.II/PD/2023-07/02-SJ).
文摘Research on scale effects on flows over weirs has been conducted on a limited basis, primarily focusing on flows upstream of a single-type weir, such as ogee, broad-crested, and sharp-crested (linear and non-linear) weirs. However, the scale effects downstream of these single-type weirs have not been thoroughly investigated. This study examined the scale effects on flows over a combined weir system consisting of an ogee weir and a sharp-crested weir, both upstream and downstream, utilizing physical modeling at a 1:33.33 scale based on Froude similarity and three-dimensional (3D) computational fluid dynamics (CFD) modeling. The sharp-crested weir in this study was represented by two sluice gates that remain closed and submerged during flood events. The experimental data confirmed that the equivalent discharge coefficients of the combined weir system behaved similarly to those of a sharp-crested weir across various H/P (where H is the total head, and P is the weir height) values. However, scale effects on the discharge rating curve due to surface tension and viscosity could only be minimized when H/P > 0.4, Re > 26 959, and We > 240 (where Re and We are the Reynolds and Weber numbers, respectively), provided that the water depth exceeded 0.042 m above the crest. Additionally, Re greater than 4 × 104 was necessary to minimize scale effects caused by viscosity in flows in the spillway channel and stilling basin (with baffle blocks). The limiting criteria aligned closely with existing literature. This study offers valuable insights for practical applications in hydraulic engineering in the future.
基金supported by the National Natural Science Foundation of China(Grant Nos.42307241 and 42107211)the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection Independent Research Project(Grant No.SKLGP2022Z008).
文摘Structure-type rockbursts frequently occur in deep tunnels,with structural planes and stress conditions being critical factors in their formation.In this study,we utilized specially developed analogous materials that exhibit the high brittleness and strength characteristics of deep hard rock to construct physical models representing different types of structural planes,including composite,exposed,non-exposed,and throughgoing structural planes.Physical simulation experiments were conducted on structuretype rockbursts in deep horseshoe-shaped tunnels,focusing on strain differentiation characteristics,critical triggering conditions,critical crack opening displacement,the incubation process,the reduction effects of structural planes on failure intensity,and formation mechanisms.These experiments were complemented by acoustic and optical monitoring,as well as discrete element numerical simulations,to provide a comprehensive analysis.The results revealed that the most significant strain heterogeneity in the surrounding rock occurs at the tip of the structural plane along the tunnel's minimum principal stress direction,driven by the combined effects of tensile and shear forces.We quantitatively determined the critical stress and strain conditions for structure-type rockbursts and evaluated the intensity of rockbursts induced by different structural planes using critical crack opening displacement(COD)values,the uniformity coefficient,and the curvature coefficient.Analysis of acoustic emission events,including frequency,amplitude,and b-value,indicated that the macro-fracture process is governed by both the principal stress differential and the characteristics of the structural plane.Furthermore,using the bearing capacity reduction coefficient,we found that exposed structural planes have the most significant weakening effect on rock mass strength,followed by non-exposed and throughgoing structural planes.The analysis of average frequency(AF)and rise angle(RA)parameters revealed a close correlation between the failure modes of structure-type rockbursts,the rock mass structure,and the stress levels.These findings provide critical theoretical support for the prediction and prevention of structure-type rockburst disasters.
基金supported by the National Natural Science Foundation of China(Grant No.52375340,51975263,52405366).
文摘A three-dimensional numerical model of laser-arc hybrid plasma for aluminum alloy fillet joints is developed in this study.This mod-el accounts for the geometric complexity of fillet joints,the physical properties of shielding gases with varying He-Ar ratios,and the coupling between arc plasma and laser-induced metal plume.The accuracy of the model is validated using a high-speed camera.The effects of varying He contents in the shielding gas on both the temperature and flow velocity of hybrid plasma,as well as the distribu-tion of laser-induced metal vapor mass,were investigated separately.The maximum temperature and size of arc plasma decrease as the He volume ratio increases,the arc distribution becomes more concentrated,and its flow velocity initially decreases and then sharply increases.At high helium content,both the flow velocity of hybrid plasma and metal vapor are high,the metal vapor is con-centrated on the right side of keyhole,and its flow appears chaotic.The flow state of arc plasma is most stable when the shielding gas consists of 50%He+50%Ar.
基金support from the National Natural Science Foundation of China (Grant Nos.51927807,42077267 and 42277174).
文摘A complex geological environment with faults can be encountered in the process of coal mining.Fault activation can cause instantaneous structure slipping,releasing a significant amount of elastic strain energy during underground coal mining.This would trigger strong rockburst disasters.To understand the occurrence of fault-slip induced rockbursts,we developed a physical model test system for fault-slip induced rockbursts in coal mine drifts.The boundary energy storage(BES)loading apparatus and bottom rapid retraction(BRR)apparatus are designed to realize energy compensation and continuous boundary stress transfer of the surrounding rocks for instantaneous fault slip,as well as to provide space for the potential fault slip.Taking the typical fault-slip induced rockburst in the Xinjulong Coal Mine,China,as the background,we conducted a model test using the test system.The deformation and stress in the rock surrounding the drift and the support unit force during fault slip are analyzed.The deformation and failure characteristics and dynamic responses of drifts under fault-slip induced rockbursts are obtained.The test results illustrate the rationality and effectiveness of the test system.Finally,corresponding recommendations and prospects are proposed based on our findings.
基金Projects(52302447,52388102,52372369)supported by the National Natural Science Foundation of China。
文摘Following the fundamental characteristics of the porosity windbreak,this study suggests a new numerical investigation method for the wind field of the windbreak based on the porous medium physical model.This method can transform the reasonable matching problem of the porosity and windproof performance of the windbreak into a study of the relationship between the resistance coefficient of the porous medium and the aerodynamic load of the train.This study examines the influence of the hole type on the wind field behind the porosity windbreak.Then,the relationship between the resistance coefficient of the porous medium,the porosity of the windbreak,and the aerodynamic loads of the train is investigated.The results show that the porous media physical model can be used instead of the windbreak geometry to study the windbreak-train aerodynamic performance,and the process of using this method is suggested.
文摘Triangle zones, generally found in foreland fold-and-thrust belts, serve as favorable objects of petroleum exploration. Taking the Dabashan foreland belt as an example, we studied the formation and development of triangle zones, and investigated the effect of d^collements and the mechanical contrast of lithology by employing the method of physical modeling. Four experimental models were conducted in the work. The results showed that ＇sand wedges＇ grew episodically, recorded by deformational length, height and slope angle. The height versus shortening rate presented an S-shape curve, and uplifting occurred successively in the direction of the foreland belt. During the formation of the triangle zone, layer-parallel shortening took place at the outset; deformation decoupling then occurred between the upper and lower brittle layers, divided by a middle-embedded silicone polymers layer. The upper brittle layers deformed mainly by folding, while the lower sand layers by thrusting. As shortening continued, the geometry of a triangle zone was altered. We consider that the triangle zone in the Dabashan foreland belt was modified from an early one based on available seismic profiles and the experimental results. In addition, dccollements and mechanical contrast impose significant influence on structural development, which can directly give rise to structural discrepancies. More d^collements and obvious mechanical contrast between brittle layers can promote the coupling between the upper and lower brittle layers. Basal d^collement controls the whole deformation and decreases the slope angle of the wedge, while roof d^collement determines whether a triangle zone can be formed.
基金funded by National Key Research and Development Plan(2018YFC0406703)Supported by the National Natural Science Foundation of China(51779277)+4 种基金Chinese Academy of Water Sciences(SD0145B072021)Supported by the State Key Laboratory of Flow Water Cycle Simulation and Regulation,SKL2022ZD05Support provided by the fund of State Key Laboratory of Water Cycle and Water Security,IWHR(Grant No.SKL2024YJZD05)Support provided by the fund of Power China(DJ-ZDXM-2020-50)Support provided by the fund of Research and Application of Intelligent Simulation and Intelligent Control Technology for Structural States of Gravity DAMS in Jingling Reservoir Project,Zhejiang Province(JLSKFW-2024113).
文摘As a critical material in construction engineering,concrete requires accurate prediction of its outlet temperature to ensure structural quality and enhance construction efficiency.This study proposes a novel hybrid prediction method that integrates a heat conduction physical model with a multilayer perceptron(MLP)neural network,dynamically fused via a weighted strategy to achieve high-precision temperature estimation.Experimental results on an independent test set demonstrated the superior performance of the fused model,with a root mean square error(RMSE)of 1.59℃ and a mean absolute error(MAE)of 1.23℃,representing a 25.3%RMSE reduction compared to conventional physical models.Ambient temperature and coarse aggregate temperature were identified as the most influential variables.Furthermore,the model-based temperature control strategy reduced costs by 0.81 CNY/m^(3),showing significant potential for improving resource efficiency and supporting sustainable construction practices.
基金Projects 2006CB202200 supported by the Special Funds for the Major State Basic Research ProjectIRT0656 by the Innovative Team Development Project of the State Educational Ministry of China
文摘In order to capture the mechanism of roadway instability in deep mines, a new approach of Physically Finite Elemental Slab Assemblage (PFESA) is proposed in order to construct a large-scale physical model simulating the geologically horizontal strata. We carried out physical modeling on the deformation and failure processes of roadways subjected to a plane loading scheme. Our laboratory tests were based on work which incorporated infrared (IR) detection, IR radiation temperature (IRT) statistics, image feature extraction and 2D Fourier transformation, from resulting thermographies. The IRT characterizes the mechanical responses from the roadway after loading with two stages, i.e., IRT evolving at higher levels corresponded to shallow mining (≤500 m) during which the roadway deformed gradually (referred to as the "steady deformation stage"); IRT evolving in a quasi-cyclical manner with multiple peaks corresponded to deep mining (800–2600 m), in which the failure mode for the roadway are dominated by breakage and collapse (called the "unsteady deformation stage"). The IR images and 2D Fourier spectra illustrate detailed information in terms of initiation, nucleation and coalescence of the damage to rock masses and the eventual failure of roadways subject to external loading.
基金supported by the National Major Scientific Instruments and Equipment Development Projects of China(No.41827808)the Major Program of the National Natural Science Foundation of China(No.42090055)Supported by Science and Technology Projects of Xizang Autonomous Region,China(No.XZ202402ZD0001)。
文摘In 2018,a catastrophic high-altitude landslide occurred at Baige,located within the tectonic suture zone of the Upper Jinsha River.The failure mechanism of this event remains poorly understood.This study aims to elucidate the deformation characteristics and failure mechanism of the Baige landslide by employing a comprehensive methodology,including field geological surveys,analysis of historical remote sensing imagery,high-density electrical resistivity surveys,and advanced displacement monitoring.Additionally,the physical modeling experiments were conducted to replicate the unique failure modes.The findings propose a novel perspective on the failure mechanism of the Baige landslide,which involves two critical stages:first,the brittle shear zone bypasses and fails at the lower locked segment,and second,the failure of the upper locked segment,combined with the shear zone's impact on the lower locked segment,triggers overall slope instability.Physical modeling experiments revealed a transition from initial acceleration to a rapid acceleration phase,particularly marked by a significant increase in velocity following the failure of the upper locked segment.The intensity of acoustic emission signals was found to correlate with the failure of the locked segments and the state of particle collisions post-failure.It offers new insights into the failure mechanisms of tectonic mélange belt large-scale landslides in suture zones,contributing to the broader field of landslide research.
文摘During actual high-speed flights,the electromagnetic(EM)properties of aircraft radomes are influenced by dielectric temperature drift,leading to substantial drift in the boresight errors(BSEs)from their room temperature values.However,applying thermal loads to the radome during ground-based EM simulation tests is challenging.This paper presents an EM equivalent physical model(EEPM)for high-speed aircraft radomes that account for the effects of dielectric temperature drift.This is achieved by attaching dielectric slices of specific thicknesses to the outer surface of a room-temperature radome(RTR)to simulate the increase in electrical thickness resulting from high temperatures.This approach enables accurate simulations of the BSEs of high-temperature radomes(HTRs)under high-speed flight conditions.An application example,supported by full-wave numerical calculations and physical testing,demonstrates that the EEPM exhibits substantial improvement in approximating the HTR compared to the RTR,facilitating precise simulations of the BSEs of HTRs during high-speed flights.Overall,the proposed EEPM is anticipated to considerably enhance the alignment between the ground-based simulations of high-speed aircraft guidance systems and their actual flight conditions.
基金the National Key Basic Research and Development Program of China(No.2015CB251600)the Preliminary National Key Basic Research and Development Program of China(No.2014CB260404)+1 种基金the National Key Natural Science Foundation of China(No.51034001,No.U13612030)the Shaanxi Innovation Team Program(No.2013KCT-16)
文摘High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slope angle was successfully implemented at the northwest wall between Nos. 4 and 5 exploration lines of Shuichang Iron Mine, taking into account the 3D scale effect. The phys-ico-mechanical properties of rock materials were obtained by laboratory tests conducted on sample cores from exploration drilling directly from the iron mine. A porous rock-like composite material was formed for the model, and the mechanical parameters of the material were assessed experimentally;specifically, the effect of water on the sample was quantitatively determined. We adopted an experimental setup using stiff modular applied static loading to carry out a visual excavation of the slope at a random depth. The setup was equipped with acous-tic emission （AE） sensors, and the experiments were monitored by crack optical acquirement, ground penetrating radar, and close-field pho-togrammetry to investigate the mechanisms of rock-mass destabilization in the high-steep slope. For the complex study area, the model re-sults indicated a clear correlation between the model＇s destabilization resulting from slope excavation and the collected monitoring informa-tion. During the model simulation, the overall angle of the slope increased by 1-6 degrees in different sections. Dramatically, the modeled excavation scheme saved over 80 million tons of rock from extraction, generating enormous economic and ecological benefits.
基金This work was supported by the National Natural Science Foundation of China(NSFC,Grant No.51874175)the China Coal Technology&Engineering Group Foundation(Grant Nos.2018RC001,KJ-2018-TDKCZL-02).Comments from two anonymous reviewers and the editor are also greatly appreciated.
文摘The evolution of mining-induced stress field in longwall panel is closely related to the fracture field and the breaking characteristics of strata.Few laboratory experiments have been conducted to investigate the stress field.This study investigated its evolution by constructing a large-scale physical model according to the in situ conditions of the longwall panel.Theoretical analysis was used to reveal the mechanism of stress distribution in the overburden.The modelling results showed that:(1)The major principal stress field is arch-shaped,and the strata overlying both the solid zones and gob constitute a series of coordinated load-bearing structures.The stress increasing zone is like a macro stress arch.High stress is especially concentrated on both shoulders of the arch-shaped structure.The stress concentration of the solid zone in front of the gob is higher than the rear solid zone.(2)The characteristics of the vertical stress field in different regions are significantly different.Stress decreases in the zone above the gob and increases in solid zones on both sides of it.The mechanical analysis show that for a given stratum,the trajectories of principal stress are arch-shaped or inverselyarched,referred to as the‘‘principal stress arch’’,irrespective of its initial breaking or periodic breaking,and determines the fracture morphology.That is,the trajectories of tensile principal stress are inversely arched before the first breaking of the strata,and cause the breaking lines to resemble an inverted funnel.In case of periodic breaking,the breaking line forms an obtuse angle with the advancing direction of the panel.Good agreement was obtained between the results of physical modeling and the theoretical analysis.
文摘The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.
基金Project supported by the National Basic Research Program (973) of China (No. 2002CB312101) and the National Natural Science Foundation of China (No. 60475013)
文摘Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scene is presented. We first propose a Two-Fluid model based on the physical theory of tornado, then we simulate the flow of tornado and its interaction with surrounding objects such as debris, etc. Taking the scattering and absorption of light by the participating media into account, the illumination effects of the tornado scene can be generated realistically. With the support of graphics hardware, various kinds of dynamic tornado scenes can be rendered at interactive rates.
基金supported by National Natural Science Foundation of China(Grant No.60975058)
文摘Non-obstacle design is critical to tailor physically handicapped workers in manufacturing system.Simultaneous consideration of variability in physically disabled users,machines and environment of the manufacturing system is extremely complex and generally requires modeling of physically handicapped interaction with the system.Most current modeling either concentrates on the task results or functional disability.The integration of physical constraints with task constraints is far more complex because of functional disability and its extended influence on adjacent body parts.A framework is proposed to integrate the two constraints and thus model the specific behavior of the physical handicapped in virtual environment generated by product specifications.Within the framework a simplified model of physical disabled body is constructed,and body motion is generated based on 3 levels of constraints(effecter constraints,kinematics constraints and physical constraints).The kinematics and dynamic calculations are made and optimized based on the weighting manipulated by the kinematics constraints and dynamic constraints.With object transferring task as example,the model is validated in Jack 6.0.Modelled task motion elements except for squatting and overreaching well matched with captured motion elements.The proposed modeling method can model the complex behavior of the physically handicapped by integrating both task and physical disability constraints.
文摘This paper introduces the seismic physical modeling technology in the CNPC Key Lab of Geophysical Exploration. It includes the seismic physical model positioning system, the data acquisition system, sources, transducers, model materials, model building techniques, precision measurements of model geometry, the basic principles of the seismic physical modeling and experimental methods, and two physical model examples.
文摘In order to examine the effectiveness of engineering protection against localized scour in front of the south groin-group of the Yangtze Estuary Waterway Improvement Project, Phase I , an undistort-ed physical model on a geometric scale of 1:250 is built in this study, covering two groins and their adacent estuarine areas. By use of rinsing fix-bed model as well as localized mobile-bed model, the experiment is undertaken under bi-directional steady flow. According to the experimental results, waterway dredging leads to the increase in steram velocity, the increase being larger during the ebb than during the flood. Construction of the upstream groin has some influence on the flow patterns near the downstream groin. Localized scour in front of the groin-heads is controlled mainly by ebb flow. In the case of a riverbed composed entirely of silt, the depths of localized scour in front of the two groin- heads are 27 m and 29 m, respectively. In reality, the underneath sediment of the prototype riverbed is clay whose threshold velocity is much higher than the stream velocity in the Yangtze Estuary; therefore, the depths of localized scour will not be much larger than the thickness of the silt layer, i. e. 7.4 m and 4.7 m, respectively. The designed aprons covering the riverbed in fron of the groin-heads are very effective in scour control. Aprons of slightly smaller size can also fulfill the task of protection, but the area of localized scour increases significantly.
