Vortex-induced vibration(VIV)of an underwater manipulator in pulsating flow presents a notable engineering problem in precise control due to the velocity variation in the flow.This study investigates the VIV response ...Vortex-induced vibration(VIV)of an underwater manipulator in pulsating flow presents a notable engineering problem in precise control due to the velocity variation in the flow.This study investigates the VIV response of an underwater manipulator subjected to pulsating flow,focusing on how different postures affect the behavior of the system.The effects of pulsating parameters and manipulator arrangement on the hydrodynamic coefficient,vibration response,motion trajectory,and vortex shedding behaviors were analyzed.Results indicated that the cross flow vibration displacement in pulsating flow increased by 32.14%compared to uniform flow,inducing a shift in the motion trajectory from a crescent shape to a sideward vase shape.In the absence of interference between the upper and lower arms,the lift coefficient of the manipulator substantially increased with rising pulsating frequency,reaching a maximum increment of 67.0%.This increase in the lift coefficient led to a 67.05%rise in the vibration frequency of the manipulator in the in-line direction.As the pulsating amplitude increased,the drag coefficient of the underwater manipulator rose by 36.79%,but the vibration frequency in the cross-flow direction decreased by 56.26%.Additionally,when the upper and lower arms remained in a state of mutual interference,the cross-flow vibration amplitudes of the upper and lower arms were approximately 1.84 and 4.82 times higher in a circular-elliptical arrangement compared to an elliptical-circular arrangement,respectively.Consequently,the flow field shifted from a P+S pattern to a disordered pattern,disrupting the regularity of the motion trajectory.展开更多
The existing deep-sea sediment plume tests are mostly under small-scale static water and rarely under large-scale flowing water conditions.In this study,large-scale tank experiments of flowing water were designed and ...The existing deep-sea sediment plume tests are mostly under small-scale static water and rarely under large-scale flowing water conditions.In this study,large-scale tank experiments of flowing water were designed and conducted to investigate the morphological characteristics and concentration evolution of the sediment plumes under different discharge rates(Q)and initial sediment concentrations(c).Viscosity tests,resuspension tests and free settling tests of the sediment solution with different c values were performed to reveal the settling mechanism of the plume diffusion process.The results show that the plume diffusion morphology variation in flowing water has four stages and the plume concentration evolution has three stages.The larger the Q,the smaller the initial incidence angle at the discharge outlet,the larger the diffusion range,the poorer the stability and the more complicated the diffusion morphology.The larger the c,the larger the settling velocity,the faster the formation of high-concentration accumulation zone,the better the stability and the clearer the diffusion boundary.The research results could provide experimental data for assessing the impact of deep-sea mining on the ocean environment.展开更多
The current research on the manufacturing of large-scale and complex components focuses mainly on the casting processes.Compared with casting,plastic forming has significant advantages in terms of performance.However,...The current research on the manufacturing of large-scale and complex components focuses mainly on the casting processes.Compared with casting,plastic forming has significant advantages in terms of performance.However,effectively controlling the material flow to achieve a reduced loading force and near-uniformity in the isothermal plastic forming process of large-scale asymmetric magnesium alloy complex housings(LSMACHs)is challenging.This study proposes a material flow control method based on the diffluence upsetting-extrusion forming(DUEF)process by dividing different forging deformation regions,combining these with the principal stress method,and establishing an efficient and accurate design procedure.A rational preformed billet was designed successfully using this method.Subsequently,a finite element simulation was employed to analyze the multiphysics fields of the DUEF process.The results indicated that compared with the traditional closed-die forging(TCDF)process,the DUEF process could control the orderly flow of materials,achieve short-distance filling of materials,and reduce hydrostatic stress.Simultaneously,it improved the deformation uniformity by 20.3%and reduced the loading force by 22.6%.Finally,the rationality of the proposed method was validated through physical experiments.Compared with the TCDF process,the DUEF process exhibited a low loading force and uniform mechanical properties.The proposed material flow control method based on the DUEF process provides a new technological approach for the plastic formation of LSMACH and similar components.展开更多
A water loop variable refrigerant flow（WLVRF）air-conditioning system is designed to be applied in large-scale buildings in northern China.The system is energy saving and it is an integrated system consisting of a va...A water loop variable refrigerant flow（WLVRF）air-conditioning system is designed to be applied in large-scale buildings in northern China.The system is energy saving and it is an integrated system consisting of a variable refrigerant flow（VRF）air-conditioning unit,a water loop and an air source heat pump.The water loop transports energy among different regions in the buildings instead of refrigerant pipes,decreasing the scale of the VRF air-conditioning unit and improving the performance.Previous models for refrigerants and building loads are cited in this investigation.Mathematical models of major equipment and other elements of the system are established using the lumped parameter method based on the DATAFIT software and the MATLAB software.The performance of the WLVRF system is simulated.The initial investments and the running costs are calculated based on the results of market research.Finally,a contrast is carried out between the WLVRF system and the traditional VRF system.The results show that the WLVRF system has a better working condition and lower running costs than the traditional VRF system.展开更多
Large-scale gold production（LSGP） is one of the five convention-related atmospheric mercury（Hg） emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process o...Large-scale gold production（LSGP） is one of the five convention-related atmospheric mercury（Hg） emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process of LSGP are limited. To identify the atmospheric Hg emission points and understand Hg emission characteristics of LSGP, Hg flows in two gold smelters were studied. Overall atmospheric Hg emissions accounted for 10%–17% of total Hg outputs and the Hg emission factors for all processes were 7.6–9.6 kg/ton. There were three dominant atmospheric Hg emission points in the studied gold smelters, including the exhaust gas of the roasting process, exhaust gas from the environmental fog collection stack and exhaust gas from the converter of the refining process. Atmospheric Hg emissions from the roasting process only accounted for 16%–29% of total emissions and the rest were emitted from the refining process. The overall Hg speciation profile（gaseous elemental Hg/gaseous oxidized Hg/particulate-bound Hg） for LSGP was 34.1/57.1/8.8. The dominant Hg output byproducts included waste acid, sulfuric acid and cyanide leaching residue. Total Hg outputs from these three byproducts were 80% in smelter A and 84% in smelter B. Our study indicated that previous atmospheric Hg emissions from large-scale gold production might have been overestimated.Hg emission control in LSGP is not especially urgent in China compared to other significant emission sources（e.g., cement plants）. Instead, LSGP is a potential Hg release source due to the high Hg output proportions to acid and sludge.展开更多
Large Eddy Simulations(LES) in conjunction with the Flamelet Progress Variable(FPV) approach have been performed to investigate the flame and large-scale flow structures in the bluff-body stabilized non-premixed flame...Large Eddy Simulations(LES) in conjunction with the Flamelet Progress Variable(FPV) approach have been performed to investigate the flame and large-scale flow structures in the bluff-body stabilized non-premixed flames, HM1 and HM3. The validity of the numerical methods is first verified by comparing the predicted velocity and composition fields with experimental measurements. Then the evolution of the flame and large-scale flow structures is analyzed when the flames approach blow-off. The analysis of instantaneous and statistical data indicates that there exists a shift of the control mechanism in the recirculation zone in the two flames. In the recirculation zone, HM1 flame is mainly controlled by the mixing effect and ignition mainly occurs in the outer shear layer. In HM3 flame, both the chemical reactions and mixing are important in the recirculation zone. The Proper Orthogonal Decomposition(POD) results show that the fluctuations in the outer shear layer are more intense in HM1, while the flow structures are more obvious in the outer vortex structure in HM3, due to the different control mechanism in the recirculation zone.It further shows that the flow structures in HM1 spread larger in the intense mixing zone due to higher temperature and less extinction.展开更多
Pulsating flow is a common condition for under water manipulators in Bohai Bay.This study aimed to investigate the effects of pulsation frequency and amplitude on the hydrodynamic characteristics of an underwater mani...Pulsating flow is a common condition for under water manipulators in Bohai Bay.This study aimed to investigate the effects of pulsation frequency and amplitude on the hydrodynamic characteristics of an underwater manipulator with different postures using the user-defined function (UDF) method. The lift coefficient (C_(L)), drag coefficient (C_(D)), and vortex shedding of the underwater manipulator in single-and dualarm forms were obtained. Results indicated that the maximum increase in the lift and drag coefficients subjected to the pulsation parameters was 24.45%and 28%, respectively, when the fluid flowed past a single arm. Compared with the single arm, the lift and drag coefficients of the arms were higher than those of the single arm when arm 2 was located upstream. Additionally, the pulsation frequency had no obvious effect on the manipulator, but the C_(L) and C_(D) of arm 2 showed an obvious increasing trend with an increase in pulsation amplitude. Meanwhile, when arm 2 was located downstream, the C_(L) and C_(D) of arm 2 were reduced by 16.38%and 1.15%, respectively, with an increase in the pulse frequency,and the maximum increase in the lift and dragcoefficients was 33.33%and 16.78%,respectively,with increasing pulsation amplitude.Moreover, the downstream wake morphology changed significantly, and a combined vortex phenomenon appeared. Finally, a theoretical basis for examining the hydrodynamic characteristics of marine engineering equipment was established to aid future marine resource exploitation.展开更多
The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation secti...The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation section paired with superhydrophilic,superhydrophobic,and hybrid condensation section).The Volume of Fluid(VOF)model was utilized to capture the phase-change process within the PHPs.The study also evaluated the influence of surface wettability on fluid patterns and thermo-dynamic heat transfer performance under various heat fluxes.The results indicated that the effective nucleation and detachment of droplets are critical factors influencing the thermal performance of the PHPs.The overall heat transfer performance of the superhydrophobic surface was significantly improved at low heat flux.Under medium to high heat flux,the superhydrophilic condensation section exhibits a strong oscillation effect and leads to the thickening of the liquid film.In addition,the hybrid surface possesses the heat transfer characteristics of both superhydrophilic and superhydrophobic walls.The hybrid condensation section exhibited the lowest thermal resistance by 0.45 K/W at the heat flux of 10731 W/m^(2).The thermal resistance is reduced by 13.1%and 5.4%,respectively,compared to the superhydrophobic and superhydrophilic conditions.The proposed surface-modification method for achieving highly efficient condensation heat transfer is helpful for the design and operation of device-cooling components.展开更多
The dynamic behaviors of a large-scale ring neural network with a triangular coupling structure are investigated.The characteristic equation of the high-dimensional system using Coate’s flow graph method is calculate...The dynamic behaviors of a large-scale ring neural network with a triangular coupling structure are investigated.The characteristic equation of the high-dimensional system using Coate’s flow graph method is calculated.Time delay is selected as the bifurcation parameter,and sufficient conditions for stability and Hopf bifurcation are derived.It is found that the connection coefficient and time delay play a crucial role in the dynamic behaviors of the model.Furthermore,a phase diagram of multiple equilibrium points with one saddle point and two stable nodes is presented.Finally,the effectiveness of the theory is verified through simulation results.展开更多
An extensive database (946 measurements) for the frequency of pulsing flow in trickle beds was established by collecting the experimental results published over past 30 years. A new correlation based on artificial neu...An extensive database (946 measurements) for the frequency of pulsing flow in trickle beds was established by collecting the experimental results published over past 30 years. A new correlation based on artificial neural network (ANN) to predict the pulsation frequency was developed. Seven dimensionless numbers (groups) employed in the proposed correlation were liquid and gas Reynolds, liquid Weber, liquid Eotvos, gas Froude, and gas Stokes numbers and a bed correction factor. The comparisons of performance reported in the of literature and present correlations show that ANN correlation is a significant improvement in predicting pulsation frequency with an average absolute relative error (AARE) of 10% and a standard deviation less than 18%.展开更多
The effects of topography on baroclinic wave flows are studied experimentally in a thermally driven rotating annulus of fluid.Fourier analysis and complex principal component (CPC) analysis of the experimental data sh...The effects of topography on baroclinic wave flows are studied experimentally in a thermally driven rotating annulus of fluid.Fourier analysis and complex principal component (CPC) analysis of the experimental data show that, due to topographic forcing, the flow is bimodal rather than a single mode. Under suitable imposed experimental parameters, near thermal Rossby number ROT = 0.1 and Taylor number Ta = 2.2 × 107, the large-scale topography produces low-frequency oscillation in the flow and rather long-lived flow pattern resembling blocking in the atmospheric circulation. The 'blocking' phenomenon is caused by the resonance of travelling waves and the quasi-stationary waves forced by topography.The large-scale topography transforms wavenumber-homogeneous flows into wavenumber-dispersed flows, and the dispersed flows possess lower wavenumbers.展开更多
In order to reduce pressure pulsation of vortex pumps,the mantis shrimp was chosen as biological prototype and a bionic engineering model was developed from its abdominal segment grooves.Bionic mantis shrimp groove vo...In order to reduce pressure pulsation of vortex pumps,the mantis shrimp was chosen as biological prototype and a bionic engineering model was developed from its abdominal segment grooves.Bionic mantis shrimp groove volute vortex pump models with different numbers of grooves were developed,and numerical simulation methods were used to calculate the models to study the effects of the volute grooves on the pressure pulsation of a vortex pump.The results show that a bionic groove volute could effectively improve the pressure pulsation of a vortex pump outlet,and reduce the pressure pulsation around the pump’s tongue and other internal points.The pressure pulsation under different conditions is impacted by shaft frequency and blade frequency.The bionic groove structure has little effect on the external characteristics of the pump,but could improve the static pressure,velocity distribution,and vortex structure of the flow field.Additionally,pressure pulsation of the whole vortex pump is reduced.展开更多
The effect of flow oscillation to the mass transfer between turbulent fluid and solid wall was investigatedby measuring the mass transfer rate between fluid and pipe wall with imposed oscillating flow usingelectrochem...The effect of flow oscillation to the mass transfer between turbulent fluid and solid wall was investigatedby measuring the mass transfer rate between fluid and pipe wall with imposed oscillating flow usingelectrochemical method.The velocity and concentration field in the viscous sublayer which controls the mass trans-fer in such a process was simulated by a simple wave model of single harmonics.Experimental results confirmthat the flow oscillation has no influene on time averaged mass transfer rate,but the phase difference betweenphase averaged velocity field and concentration field shifts with the frequency of imposed oscillating flow.Numeri-cal analysis reveals that the concentration boundarylayer which is responsible for the mass transfer is muchthinner than the viscous sublayer which greatly weakens the influence of imposed oscillating flow on mass transfer.展开更多
Based on a suite of computational fluid dynamics code, the pulsation characteristics are studied for turbulent supercavitating flows over a 2D base-vented symmetric hydrofoil using a pressure-based Navier-Stokes solve...Based on a suite of computational fluid dynamics code, the pulsation characteristics are studied for turbulent supercavitating flows over a 2D base-vented symmetric hydrofoil using a pressure-based Navier-Stokes solver coupled with a phase mass fraction transport cavitation model and local linear low-Reynolds-number k-ε turbulence model. It is found that there exists a critical air supply flow under certain inflow condition. When the gas supply flow exceeds the critical value, the cavity begins to pulsate. Pulsating cavity has a visually wavy surface, and air leakage shows as a mass of air-water mixture detaching from the rear part of the cavity periodically.展开更多
In this paper,we focus on the two-dimensional pulsating nanofluid flow through a parallel-plate channel in the presence of a magnetic field.The pulsating flow is produced by an applied pressure gradient that fluctuate...In this paper,we focus on the two-dimensional pulsating nanofluid flow through a parallel-plate channel in the presence of a magnetic field.The pulsating flow is produced by an applied pressure gradient that fluctuates with a small amplitude.A kind of proper transformation is used so that the governing equations describing the momentum and thermal energy are reduced to a set of non-dimensional equations.The analytical expressions of the pulsating velocity,temperature,and Nusselt number of nanofluids are obtained by the perturbation technique.In the present study,the effects of the Cu-H2O and Al_(2)O_(3)-H2O nanofluids on the flow and heat transfer in pulsating flow are compared and analyzed.The results show that the convective heat transfer effect of Cu-H2O nanofluids is better than that of Al_(2)O_(3)-H2O nanofluids.Also,the effects of the Hartmann number and pulsation amplitude on the velocity,temperature,and Nusselt number are examined and discussed in detail.The present work indicates that increasing the Hartmann number and pulsation amplitude can enhance the heat transfer of the pulsating flow.In addition,selecting an optimal pulsation frequency can maximize the convective heat transfer of the pulsating flow.Therefore,improved understanding of these fundamental mechanisms is conducive to the optimal design of thermal systems.展开更多
CO_(2) electroreduction(CO_(2) ER)to high value-added chemicals is considered as a promising technology to achieve sustainable carbon neutralization.By virtue of the progressive research in recent years aiming at desi...CO_(2) electroreduction(CO_(2) ER)to high value-added chemicals is considered as a promising technology to achieve sustainable carbon neutralization.By virtue of the progressive research in recent years aiming at design and understanding of catalytic materials and electrolyte systems,the CO_(2) ER performance(such as current density,selectivity,stability,CO_(2) conversion,etc.)has been continually increased.Unfortunately,there has been relatively little attention paid to the large-scale CO 2 electrolyzers,which stand just as one obstacle,alongside series-parallel integration,challenging the practical application of this infant technology.In this review,the latest progress on the structures of low-temperature CO_(2) electrolyzers and scale-up studies was systematically overviewed.The influence of the CO_(2) electrolyzer configurations,such as the flow channel design,gas diffusion electrode(GDE)and ion exchange membrane(IEM),on the CO_(2) ER performance was further discussed.The review could provide inspiration for the design of large-scale CO_(2) electrolyzers so as to accelerate the industrial application of CO_(2) ER technology.展开更多
This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined d...This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.展开更多
A three-dimensional thermoregulation mathematical model of temperature fluctuations for the human body is developed based on predecessors＇ thermal models. The following improvements are necessary in real situations：...A three-dimensional thermoregulation mathematical model of temperature fluctuations for the human body is developed based on predecessors＇ thermal models. The following improvements are necessary in real situations： ellipsoids and elliptical cylinders are used to adequately approximate body geometry, divided into 18 segments and five layers; the core layer consists of the organs; the pulsation of the heart cycle, the pulsatile laminar flow, the peripheral resistance, and the thermal effect of food are considered. The model is calculated by adopting computational fluid dynamics（CFD） technology, and the results of the model match with the experimental data. This paper can give a reasonable explanation for the temperature fluctuations.展开更多
This paper introduces an improvement to electrochemical drilling process by coupling flow field and electric field in pulsating state. A novel tube with half-wedged shape at the end(HW-tube) is prepared, with both sid...This paper introduces an improvement to electrochemical drilling process by coupling flow field and electric field in pulsating state. A novel tube with half-wedged shape at the end(HW-tube) is prepared, with both sidewall and wedged part of the HW-tube insulated. Only the flat part is utilized to provide electric field for electrochemical drilling. By rotating the HW-tube, both flow field and electric field in pulsating state are generated, alternating in different positions within the inter-electrode gap(IEG). The pulsating flow field enhances the mass transfer process, while pulsating electric field disperses material dissolution process and distribution of electrolytic byproducts. Both pulsating fields are coupled at the same frequency, further enhancing the electrochemical drilling process. Simulation results indicate that both flow field and electric field in pulsating state are generated. Compared to the traditional tube, the HW-tube significantly reduces the number of residual particles in IEG, and this number is further reduced by increasing the rotation speed. Experimental results reveal that the surface quality and dimensional uniformity of small hole are improved with HW-tube. With feed rate of 2.22 mm/min, a small hole with diameter of 1.52± 0.017 mm is drilled, resulting in a surface roughness of 0.331 μm.展开更多
基金Supported by the National Natural Science Foundation of China(No.51905211)A Project of the“20 Regulations for New Universities”Funding Program of Jinan(No.202228116).
文摘Vortex-induced vibration(VIV)of an underwater manipulator in pulsating flow presents a notable engineering problem in precise control due to the velocity variation in the flow.This study investigates the VIV response of an underwater manipulator subjected to pulsating flow,focusing on how different postures affect the behavior of the system.The effects of pulsating parameters and manipulator arrangement on the hydrodynamic coefficient,vibration response,motion trajectory,and vortex shedding behaviors were analyzed.Results indicated that the cross flow vibration displacement in pulsating flow increased by 32.14%compared to uniform flow,inducing a shift in the motion trajectory from a crescent shape to a sideward vase shape.In the absence of interference between the upper and lower arms,the lift coefficient of the manipulator substantially increased with rising pulsating frequency,reaching a maximum increment of 67.0%.This increase in the lift coefficient led to a 67.05%rise in the vibration frequency of the manipulator in the in-line direction.As the pulsating amplitude increased,the drag coefficient of the underwater manipulator rose by 36.79%,but the vibration frequency in the cross-flow direction decreased by 56.26%.Additionally,when the upper and lower arms remained in a state of mutual interference,the cross-flow vibration amplitudes of the upper and lower arms were approximately 1.84 and 4.82 times higher in a circular-elliptical arrangement compared to an elliptical-circular arrangement,respectively.Consequently,the flow field shifted from a P+S pattern to a disordered pattern,disrupting the regularity of the motion trajectory.
基金supported by the Major Project of Hunan Natural Science Foundation,China(No.2021JC0010)the National Natural Science Foundation of China(No.51274251)。
文摘The existing deep-sea sediment plume tests are mostly under small-scale static water and rarely under large-scale flowing water conditions.In this study,large-scale tank experiments of flowing water were designed and conducted to investigate the morphological characteristics and concentration evolution of the sediment plumes under different discharge rates(Q)and initial sediment concentrations(c).Viscosity tests,resuspension tests and free settling tests of the sediment solution with different c values were performed to reveal the settling mechanism of the plume diffusion process.The results show that the plume diffusion morphology variation in flowing water has four stages and the plume concentration evolution has three stages.The larger the Q,the smaller the initial incidence angle at the discharge outlet,the larger the diffusion range,the poorer the stability and the more complicated the diffusion morphology.The larger the c,the larger the settling velocity,the faster the formation of high-concentration accumulation zone,the better the stability and the clearer the diffusion boundary.The research results could provide experimental data for assessing the impact of deep-sea mining on the ocean environment.
基金Supported by National Natural Science Foundation of China(Grant No.52075501).
文摘The current research on the manufacturing of large-scale and complex components focuses mainly on the casting processes.Compared with casting,plastic forming has significant advantages in terms of performance.However,effectively controlling the material flow to achieve a reduced loading force and near-uniformity in the isothermal plastic forming process of large-scale asymmetric magnesium alloy complex housings(LSMACHs)is challenging.This study proposes a material flow control method based on the diffluence upsetting-extrusion forming(DUEF)process by dividing different forging deformation regions,combining these with the principal stress method,and establishing an efficient and accurate design procedure.A rational preformed billet was designed successfully using this method.Subsequently,a finite element simulation was employed to analyze the multiphysics fields of the DUEF process.The results indicated that compared with the traditional closed-die forging(TCDF)process,the DUEF process could control the orderly flow of materials,achieve short-distance filling of materials,and reduce hydrostatic stress.Simultaneously,it improved the deformation uniformity by 20.3%and reduced the loading force by 22.6%.Finally,the rationality of the proposed method was validated through physical experiments.Compared with the TCDF process,the DUEF process exhibited a low loading force and uniform mechanical properties.The proposed material flow control method based on the DUEF process provides a new technological approach for the plastic formation of LSMACH and similar components.
文摘A water loop variable refrigerant flow（WLVRF）air-conditioning system is designed to be applied in large-scale buildings in northern China.The system is energy saving and it is an integrated system consisting of a variable refrigerant flow（VRF）air-conditioning unit,a water loop and an air source heat pump.The water loop transports energy among different regions in the buildings instead of refrigerant pipes,decreasing the scale of the VRF air-conditioning unit and improving the performance.Previous models for refrigerants and building loads are cited in this investigation.Mathematical models of major equipment and other elements of the system are established using the lumped parameter method based on the DATAFIT software and the MATLAB software.The performance of the WLVRF system is simulated.The initial investments and the running costs are calculated based on the results of market research.Finally,a contrast is carried out between the WLVRF system and the traditional VRF system.The results show that the WLVRF system has a better working condition and lower running costs than the traditional VRF system.
基金supported by the National basic Research Program (973) of China (No.2013CB430001)the National Natural Science Foundation of China (No.21077065)the China Postdoctoral Science Foundation (2016T90103,2016M601053)
文摘Large-scale gold production（LSGP） is one of the five convention-related atmospheric mercury（Hg） emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process of LSGP are limited. To identify the atmospheric Hg emission points and understand Hg emission characteristics of LSGP, Hg flows in two gold smelters were studied. Overall atmospheric Hg emissions accounted for 10%–17% of total Hg outputs and the Hg emission factors for all processes were 7.6–9.6 kg/ton. There were three dominant atmospheric Hg emission points in the studied gold smelters, including the exhaust gas of the roasting process, exhaust gas from the environmental fog collection stack and exhaust gas from the converter of the refining process. Atmospheric Hg emissions from the roasting process only accounted for 16%–29% of total emissions and the rest were emitted from the refining process. The overall Hg speciation profile（gaseous elemental Hg/gaseous oxidized Hg/particulate-bound Hg） for LSGP was 34.1/57.1/8.8. The dominant Hg output byproducts included waste acid, sulfuric acid and cyanide leaching residue. Total Hg outputs from these three byproducts were 80% in smelter A and 84% in smelter B. Our study indicated that previous atmospheric Hg emissions from large-scale gold production might have been overestimated.Hg emission control in LSGP is not especially urgent in China compared to other significant emission sources（e.g., cement plants）. Instead, LSGP is a potential Hg release source due to the high Hg output proportions to acid and sludge.
基金supported by the National Natural Science Foundation of China(Nos.91441202 and 51476087)
文摘Large Eddy Simulations(LES) in conjunction with the Flamelet Progress Variable(FPV) approach have been performed to investigate the flame and large-scale flow structures in the bluff-body stabilized non-premixed flames, HM1 and HM3. The validity of the numerical methods is first verified by comparing the predicted velocity and composition fields with experimental measurements. Then the evolution of the flame and large-scale flow structures is analyzed when the flames approach blow-off. The analysis of instantaneous and statistical data indicates that there exists a shift of the control mechanism in the recirculation zone in the two flames. In the recirculation zone, HM1 flame is mainly controlled by the mixing effect and ignition mainly occurs in the outer shear layer. In HM3 flame, both the chemical reactions and mixing are important in the recirculation zone. The Proper Orthogonal Decomposition(POD) results show that the fluctuations in the outer shear layer are more intense in HM1, while the flow structures are more obvious in the outer vortex structure in HM3, due to the different control mechanism in the recirculation zone.It further shows that the flow structures in HM1 spread larger in the intense mixing zone due to higher temperature and less extinction.
基金the National Natural Science Foundation of China (No. 51905211)China Postdoctoral Science Foundation (Grant No. 2020M672128)+1 种基金University of Jinan Research Startup and Discipline Construction Fund (Grant No.1009435)a Project of the “20 Regulations for New Universities” funding program of Jinan (No.202228116)。
文摘Pulsating flow is a common condition for under water manipulators in Bohai Bay.This study aimed to investigate the effects of pulsation frequency and amplitude on the hydrodynamic characteristics of an underwater manipulator with different postures using the user-defined function (UDF) method. The lift coefficient (C_(L)), drag coefficient (C_(D)), and vortex shedding of the underwater manipulator in single-and dualarm forms were obtained. Results indicated that the maximum increase in the lift and drag coefficients subjected to the pulsation parameters was 24.45%and 28%, respectively, when the fluid flowed past a single arm. Compared with the single arm, the lift and drag coefficients of the arms were higher than those of the single arm when arm 2 was located upstream. Additionally, the pulsation frequency had no obvious effect on the manipulator, but the C_(L) and C_(D) of arm 2 showed an obvious increasing trend with an increase in pulsation amplitude. Meanwhile, when arm 2 was located downstream, the C_(L) and C_(D) of arm 2 were reduced by 16.38%and 1.15%, respectively, with an increase in the pulse frequency,and the maximum increase in the lift and dragcoefficients was 33.33%and 16.78%,respectively,with increasing pulsation amplitude.Moreover, the downstream wake morphology changed significantly, and a combined vortex phenomenon appeared. Finally, a theoretical basis for examining the hydrodynamic characteristics of marine engineering equipment was established to aid future marine resource exploitation.
基金support by Beijing Natural Science Foundation(3194046)BUCEA Post Graduate Innovation Project.
文摘The present work deals with the numerical study of the two-phase flow pattern and heat transfer characteristics of single-loop pulsating heat pipes(PHPs)under three modified surfaces(superhydrophilic evaporation section paired with superhydrophilic,superhydrophobic,and hybrid condensation section).The Volume of Fluid(VOF)model was utilized to capture the phase-change process within the PHPs.The study also evaluated the influence of surface wettability on fluid patterns and thermo-dynamic heat transfer performance under various heat fluxes.The results indicated that the effective nucleation and detachment of droplets are critical factors influencing the thermal performance of the PHPs.The overall heat transfer performance of the superhydrophobic surface was significantly improved at low heat flux.Under medium to high heat flux,the superhydrophilic condensation section exhibits a strong oscillation effect and leads to the thickening of the liquid film.In addition,the hybrid surface possesses the heat transfer characteristics of both superhydrophilic and superhydrophobic walls.The hybrid condensation section exhibited the lowest thermal resistance by 0.45 K/W at the heat flux of 10731 W/m^(2).The thermal resistance is reduced by 13.1%and 5.4%,respectively,compared to the superhydrophobic and superhydrophilic conditions.The proposed surface-modification method for achieving highly efficient condensation heat transfer is helpful for the design and operation of device-cooling components.
基金Supported by Natural Science Foundation of Shandong Province of China(Grant Nos.ZR2020MF080 and ZR2020MF065).
文摘The dynamic behaviors of a large-scale ring neural network with a triangular coupling structure are investigated.The characteristic equation of the high-dimensional system using Coate’s flow graph method is calculated.Time delay is selected as the bifurcation parameter,and sufficient conditions for stability and Hopf bifurcation are derived.It is found that the connection coefficient and time delay play a crucial role in the dynamic behaviors of the model.Furthermore,a phase diagram of multiple equilibrium points with one saddle point and two stable nodes is presented.Finally,the effectiveness of the theory is verified through simulation results.
基金the State Key Development Program for Basic Research of China (No. G2000048005)the SINOPEC (X503023).
文摘An extensive database (946 measurements) for the frequency of pulsing flow in trickle beds was established by collecting the experimental results published over past 30 years. A new correlation based on artificial neural network (ANN) to predict the pulsation frequency was developed. Seven dimensionless numbers (groups) employed in the proposed correlation were liquid and gas Reynolds, liquid Weber, liquid Eotvos, gas Froude, and gas Stokes numbers and a bed correction factor. The comparisons of performance reported in the of literature and present correlations show that ANN correlation is a significant improvement in predicting pulsation frequency with an average absolute relative error (AARE) of 10% and a standard deviation less than 18%.
基金This research was supported by the U.S. National Science Foundation Grants ATM-8709410 and ATM-8714674.
文摘The effects of topography on baroclinic wave flows are studied experimentally in a thermally driven rotating annulus of fluid.Fourier analysis and complex principal component (CPC) analysis of the experimental data show that, due to topographic forcing, the flow is bimodal rather than a single mode. Under suitable imposed experimental parameters, near thermal Rossby number ROT = 0.1 and Taylor number Ta = 2.2 × 107, the large-scale topography produces low-frequency oscillation in the flow and rather long-lived flow pattern resembling blocking in the atmospheric circulation. The 'blocking' phenomenon is caused by the resonance of travelling waves and the quasi-stationary waves forced by topography.The large-scale topography transforms wavenumber-homogeneous flows into wavenumber-dispersed flows, and the dispersed flows possess lower wavenumbers.
基金Projects(51779226,51476144)supported by the National Natural Science Foundation of ChinaProject(2017C31025)supported by Zhejiang Province Department Public Welfare Industrial Projects,China+1 种基金Project(2016M601736)supported by Postdoctoral Science Foundation of ChinaProject(1601028C)supported by Postdoctoral Research Funding Plan in Jiangsu Province,China
文摘In order to reduce pressure pulsation of vortex pumps,the mantis shrimp was chosen as biological prototype and a bionic engineering model was developed from its abdominal segment grooves.Bionic mantis shrimp groove volute vortex pump models with different numbers of grooves were developed,and numerical simulation methods were used to calculate the models to study the effects of the volute grooves on the pressure pulsation of a vortex pump.The results show that a bionic groove volute could effectively improve the pressure pulsation of a vortex pump outlet,and reduce the pressure pulsation around the pump’s tongue and other internal points.The pressure pulsation under different conditions is impacted by shaft frequency and blade frequency.The bionic groove structure has little effect on the external characteristics of the pump,but could improve the static pressure,velocity distribution,and vortex structure of the flow field.Additionally,pressure pulsation of the whole vortex pump is reduced.
文摘The effect of flow oscillation to the mass transfer between turbulent fluid and solid wall was investigatedby measuring the mass transfer rate between fluid and pipe wall with imposed oscillating flow usingelectrochemical method.The velocity and concentration field in the viscous sublayer which controls the mass trans-fer in such a process was simulated by a simple wave model of single harmonics.Experimental results confirmthat the flow oscillation has no influene on time averaged mass transfer rate,but the phase difference betweenphase averaged velocity field and concentration field shifts with the frequency of imposed oscillating flow.Numeri-cal analysis reveals that the concentration boundarylayer which is responsible for the mass transfer is muchthinner than the viscous sublayer which greatly weakens the influence of imposed oscillating flow on mass transfer.
基金the National Natural Science Foundation of China(No:10832007)the Shanghai Leading Academic Discipline Project(No.B206)
文摘Based on a suite of computational fluid dynamics code, the pulsation characteristics are studied for turbulent supercavitating flows over a 2D base-vented symmetric hydrofoil using a pressure-based Navier-Stokes solver coupled with a phase mass fraction transport cavitation model and local linear low-Reynolds-number k-ε turbulence model. It is found that there exists a critical air supply flow under certain inflow condition. When the gas supply flow exceeds the critical value, the cavity begins to pulsate. Pulsating cavity has a visually wavy surface, and air leakage shows as a mass of air-water mixture detaching from the rear part of the cavity periodically.
基金Project supported by the China Postdoctoral Science Foundation(No.2018M631909)the Doctor of Entrepreneurship and Innovation Project of Jiangsu Province(No.JSSCBS20221300)。
文摘In this paper,we focus on the two-dimensional pulsating nanofluid flow through a parallel-plate channel in the presence of a magnetic field.The pulsating flow is produced by an applied pressure gradient that fluctuates with a small amplitude.A kind of proper transformation is used so that the governing equations describing the momentum and thermal energy are reduced to a set of non-dimensional equations.The analytical expressions of the pulsating velocity,temperature,and Nusselt number of nanofluids are obtained by the perturbation technique.In the present study,the effects of the Cu-H2O and Al_(2)O_(3)-H2O nanofluids on the flow and heat transfer in pulsating flow are compared and analyzed.The results show that the convective heat transfer effect of Cu-H2O nanofluids is better than that of Al_(2)O_(3)-H2O nanofluids.Also,the effects of the Hartmann number and pulsation amplitude on the velocity,temperature,and Nusselt number are examined and discussed in detail.The present work indicates that increasing the Hartmann number and pulsation amplitude can enhance the heat transfer of the pulsating flow.In addition,selecting an optimal pulsation frequency can maximize the convective heat transfer of the pulsating flow.Therefore,improved understanding of these fundamental mechanisms is conducive to the optimal design of thermal systems.
基金supported by National Key R&D Program of China(2020YFA0710200)the National Natural Science Foundation of China(21838010,22122814)+2 种基金the Youth Innovation Promotion Association of the Chinese Academy of Sciences(2018064)State Key Laboratory of Multiphase complex systems,Institute of Process Engineering,Chinese Academy of Sciences(No.MPCS-2022-A-03)Innovation Academy for Green Manufacture Institute,Chinese Academy of Science(IAGM2020C14).
文摘CO_(2) electroreduction(CO_(2) ER)to high value-added chemicals is considered as a promising technology to achieve sustainable carbon neutralization.By virtue of the progressive research in recent years aiming at design and understanding of catalytic materials and electrolyte systems,the CO_(2) ER performance(such as current density,selectivity,stability,CO_(2) conversion,etc.)has been continually increased.Unfortunately,there has been relatively little attention paid to the large-scale CO 2 electrolyzers,which stand just as one obstacle,alongside series-parallel integration,challenging the practical application of this infant technology.In this review,the latest progress on the structures of low-temperature CO_(2) electrolyzers and scale-up studies was systematically overviewed.The influence of the CO_(2) electrolyzer configurations,such as the flow channel design,gas diffusion electrode(GDE)and ion exchange membrane(IEM),on the CO_(2) ER performance was further discussed.The review could provide inspiration for the design of large-scale CO_(2) electrolyzers so as to accelerate the industrial application of CO_(2) ER technology.
基金the Ger man National Science Foundation (GR-412/33-2)Shanghai Leading Academic Discipline Project (No.B604)
文摘This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.
基金Project supported by the National Basic Research Program of China(Grant No.2010CB734101)the National Natural Science Foundation of China(Grant No.51705332)
文摘A three-dimensional thermoregulation mathematical model of temperature fluctuations for the human body is developed based on predecessors＇ thermal models. The following improvements are necessary in real situations： ellipsoids and elliptical cylinders are used to adequately approximate body geometry, divided into 18 segments and five layers; the core layer consists of the organs; the pulsation of the heart cycle, the pulsatile laminar flow, the peripheral resistance, and the thermal effect of food are considered. The model is calculated by adopting computational fluid dynamics（CFD） technology, and the results of the model match with the experimental data. This paper can give a reasonable explanation for the temperature fluctuations.
基金supported by National Natural Science Foundation of China (No. 52075105)Natural Science Foundation of Guangdong Province (No. 2023A1515012028)。
文摘This paper introduces an improvement to electrochemical drilling process by coupling flow field and electric field in pulsating state. A novel tube with half-wedged shape at the end(HW-tube) is prepared, with both sidewall and wedged part of the HW-tube insulated. Only the flat part is utilized to provide electric field for electrochemical drilling. By rotating the HW-tube, both flow field and electric field in pulsating state are generated, alternating in different positions within the inter-electrode gap(IEG). The pulsating flow field enhances the mass transfer process, while pulsating electric field disperses material dissolution process and distribution of electrolytic byproducts. Both pulsating fields are coupled at the same frequency, further enhancing the electrochemical drilling process. Simulation results indicate that both flow field and electric field in pulsating state are generated. Compared to the traditional tube, the HW-tube significantly reduces the number of residual particles in IEG, and this number is further reduced by increasing the rotation speed. Experimental results reveal that the surface quality and dimensional uniformity of small hole are improved with HW-tube. With feed rate of 2.22 mm/min, a small hole with diameter of 1.52± 0.017 mm is drilled, resulting in a surface roughness of 0.331 μm.
