Characterization of the microstructure of the fusion zone of an Alloy 600-82 weld joint was conducted, with focus on the weld residual strain distribution and the comparison of the microstructure of heat affected zone...Characterization of the microstructure of the fusion zone of an Alloy 600-82 weld joint was conducted, with focus on the weld residual strain distribution and the comparison of the microstructure of heat affected zone （HAZ） with that of cold worked alloy. Peak of the residual strain was observed to approach to the fusion boundary in HAZ while the strain increased from the top of the weld to the root. Strain distribution in the HAZ was found to be concentrated adjacent to grain boundaries （GBs）, with a peak of approximately three times of that in grain. Further, triple junctions of the GB appear to cause a higher strain concentration than single GBs. The microstructure of HAZ consists of partially tangled dislocations, which is different from slip bands of high density dislocations in cold worked alloy. This may cause a relatively higher intergranular cracking resistance of HAZ due to the difficulty in transferring tangled dislocations to GB in HAZ under deformation.展开更多
Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens wer...Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens were extracted from specific regions(base metal, weld metal, and three heat-affected zones) of API X80 and X70 weld joints. Uniaxial tensile tests were conducted to obtain the mechanical properties of different regions, and then uniaxial ratcheting tests were conducted to investigate the ratcheting behaviors of the different regions under the same peak and nominal stresses. Under both the tensile tests and ratcheting tests, the weld joints exhibit heterogeneous results, such as different mechanical properties and ratcheting behaviors, which were region dependent. Furthermore, the yield strength and yield-to-tensile strength ratio contribute differently to the ratcheting response.展开更多
An idealized tri-material assumption is established to describe the constitutive relationship of mismatched welded joints by considering the influence of heat affected zone（HAZ）.The fracture parameters Jand C＊are e...An idealized tri-material assumption is established to describe the constitutive relationship of mismatched welded joints by considering the influence of heat affected zone（HAZ）.The fracture parameters Jand C＊are estimated for mismatched welded joints with HAZ cracks by finite element analysis with ABAQUS.A middle crack tension（M（T））specimen is utilized in the analysis for different material properties and geometries of the weldment.The influence of mechanical property and geometry on the fracture parameters Jand C＊of the specimen is discussed for the welded joints with HAZ crack.The results suggest that the HAZ property is a significant factor in the estimation of Jand C＊for the mismatched welded joint with HAZ crack.展开更多
It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power...It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power Spectral Density） function is developed using wave propagation theory, while for vertical incidence of waves the cross-PSD function is composed by auto-PSD model, coherence model and site response model. As the seismic input, the eross-PSD function is used to calculate the the axial and lateral seismic responses of underground pipeline through the fracture zone. The results show that the incident directions of seismic waves, width and soil property of the fracture zone have great influence on underground pipeline. It is suggested that the flexible joints with appropriate stiffness should be added into the pipeline near the interfaces between the fracture zone and the surrounded media.展开更多
Fracture parameters of welded joints with different strength matching and crack depth in weld metal are investigated by using the methods of elastoplastic finite element analysis and three point bend specimen test. Th...Fracture parameters of welded joints with different strength matching and crack depth in weld metal are investigated by using the methods of elastoplastic finite element analysis and three point bend specimen test. The results show that for shallow crack, the plastic zone turns large in loading process, and the fracture toughness turns high. The extent of the plastic zone of overmatched joint is larger than that of undermatched joint because it will extends to parent metal from the weld metal in loading process for the same CTOD value. The plastic zone of undermatched joint is restricted within the weld, and the size of that is small. Overmatched joint shows the fracture behaviour of shallow crack may more easily than the undermatched joint, while the two sorts of joint specimens have the same crack depth. Therefore, the fracture-resistant capability of overmatched weld is better than that of undermatched weld. when the toughness of weld metals is similar for both overmatched and undermatched joints.展开更多
Yushu Ms7.1 earthquake occurred on the Ganzi-Yushu fault zone, across which we carried out a joint relative-gravity and seismic-reflection survey, and then performed a gravity inversion constrained by the seismic-refl...Yushu Ms7.1 earthquake occurred on the Ganzi-Yushu fault zone, across which we carried out a joint relative-gravity and seismic-reflection survey, and then performed a gravity inversion constrained by the seismic-reflection result. Based on the data of complete Bouguer gravity anomaly and seismic reflection, we obtained a layered interface structure in deep crust down to Moho. Our study showed that the inversion could reveal the interfaces of strata along the survey profile and the directions of regional faults in two-dimension. From the characteristics of the observed topography of the Moho basement, we tentatively confirmed that the uplift of eastern edge of Qinghai-Tibet plateau was caused by the subduetion of the Indian plate.展开更多
Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided in...Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided into three zones, including elastic zone, plastic damage zone and shear fracture zone for assessing the stability of the tunnel surrounding rock. By local hydrogeology, the stresses of surrounding rock of Jinshazhou circular tunnel was analyzed and the stress solutions on the elastic and plastic damage zones were obtained by applying the theories of fluid-solid coupling and elasto-plastic damage mechanics. The shear fracture zone generated by joints was studied and its range was determined by using Molar-Coulomb strength criterion. Finally, the correctness of the theoretical results was validated by comparing the scopes of shear fracture zones calculated in this paper with those from literature.展开更多
This is a field report on a comprehensive study of the Atamir Formation from the engineering geology perspective using the related indices. The Atamir Formation of the Cretaceous Period, which has outcropped in the fo...This is a field report on a comprehensive study of the Atamir Formation from the engineering geology perspective using the related indices. The Atamir Formation of the Cretaceous Period, which has outcropped in the form of thick frequencies of grey-knotted sandstone and black shales, is situated in the Kope Dagh zone. A survey of discontinuities together with bedding was carried out to study slope stability. The layers have a general east-west trend with a gentle slope towards the south. Because of the tectonic and stratigraphic differences, and with the purpose of facilitating surveys related to joint study of the outcrop, the formation in the study region was divided into three units. The lower unit is made of shale, the middle of sandstone, and the upper of marlstone. All three units were studied from the perspective of geomechanical classification, rock mass indices, geological strength, geomechanical indices, and wedge instability analysis under dry and wet conditions, and the results were investigated in the form of various images and figures. The Dips software was used to display the rose diagram and stereographic projection of each unit, the Swedge software to analyze instability of the wedges, and the Roctab software to analyze the geomechanical parameters and present the outputs along with the description of each unit.展开更多
High chromium （9-12% Cr） steels with excellent heat resistance and CrMoV steels with good toughness were potential candidates for combined rotor for steam turbine operated over 620℃. Two welding techniques were use...High chromium （9-12% Cr） steels with excellent heat resistance and CrMoV steels with good toughness were potential candidates for combined rotor for steam turbine operated over 620℃. Two welding techniques were used to fabricate 9% Cr and CrMoV dissimilar welded joint. The results show that the carbon migration only appears in the specimen using narrow gap submerged arc welding （NG-SAW） technique, yet it can be effectively prevented by adding tungsten inert gas （TlG） overlaying process before the NG-SAW. The carbon migration occurred in NG-SAW resulting from the sharp transition of the strong carbide-forming element Cr between the weld （-2.7 wt%） and the base metal （- 9 wt%）. On the contrary, the application of TIG overlaying layers can promote the diffusion of Cr element, and therefore result in its much smaller concentration gradient. That is to say, a gentle transition zone of Cr element can be created among the SAW weld, TIG overlaying layers and the base metal, which effectively prevents the carbon migration and therefore produces a decreased carbon concentration adjacent to the fusion line.展开更多
基金financially supported by the Hundred-Talent Program of Chinese Academy of Sciences
文摘Characterization of the microstructure of the fusion zone of an Alloy 600-82 weld joint was conducted, with focus on the weld residual strain distribution and the comparison of the microstructure of heat affected zone （HAZ） with that of cold worked alloy. Peak of the residual strain was observed to approach to the fusion boundary in HAZ while the strain increased from the top of the weld to the root. Strain distribution in the HAZ was found to be concentrated adjacent to grain boundaries （GBs）, with a peak of approximately three times of that in grain. Further, triple junctions of the GB appear to cause a higher strain concentration than single GBs. The microstructure of HAZ consists of partially tangled dislocations, which is different from slip bands of high density dislocations in cold worked alloy. This may cause a relatively higher intergranular cracking resistance of HAZ due to the difficulty in transferring tangled dislocations to GB in HAZ under deformation.
基金supported by the National Natural Science Foundation of China (No. 51435012)
文摘Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens were extracted from specific regions(base metal, weld metal, and three heat-affected zones) of API X80 and X70 weld joints. Uniaxial tensile tests were conducted to obtain the mechanical properties of different regions, and then uniaxial ratcheting tests were conducted to investigate the ratcheting behaviors of the different regions under the same peak and nominal stresses. Under both the tensile tests and ratcheting tests, the weld joints exhibit heterogeneous results, such as different mechanical properties and ratcheting behaviors, which were region dependent. Furthermore, the yield strength and yield-to-tensile strength ratio contribute differently to the ratcheting response.
基金Sponsored by National High Technology Research and Development Program of China(2012AA040106)
文摘An idealized tri-material assumption is established to describe the constitutive relationship of mismatched welded joints by considering the influence of heat affected zone（HAZ）.The fracture parameters Jand C＊are estimated for mismatched welded joints with HAZ cracks by finite element analysis with ABAQUS.A middle crack tension（M（T））specimen is utilized in the analysis for different material properties and geometries of the weldment.The influence of mechanical property and geometry on the fracture parameters Jand C＊of the specimen is discussed for the welded joints with HAZ crack.The results suggest that the HAZ property is a significant factor in the estimation of Jand C＊for the mismatched welded joint with HAZ crack.
文摘It is assumed that a pipeline is laid through a vertical fault fracture zone, and is excited by seismic ground motion modelled as stationary stochastic process. For horizontal incidence of waves, the cross-PSD （Power Spectral Density） function is developed using wave propagation theory, while for vertical incidence of waves the cross-PSD function is composed by auto-PSD model, coherence model and site response model. As the seismic input, the eross-PSD function is used to calculate the the axial and lateral seismic responses of underground pipeline through the fracture zone. The results show that the incident directions of seismic waves, width and soil property of the fracture zone have great influence on underground pipeline. It is suggested that the flexible joints with appropriate stiffness should be added into the pipeline near the interfaces between the fracture zone and the surrounded media.
文摘Fracture parameters of welded joints with different strength matching and crack depth in weld metal are investigated by using the methods of elastoplastic finite element analysis and three point bend specimen test. The results show that for shallow crack, the plastic zone turns large in loading process, and the fracture toughness turns high. The extent of the plastic zone of overmatched joint is larger than that of undermatched joint because it will extends to parent metal from the weld metal in loading process for the same CTOD value. The plastic zone of undermatched joint is restricted within the weld, and the size of that is small. Overmatched joint shows the fracture behaviour of shallow crack may more easily than the undermatched joint, while the two sorts of joint specimens have the same crack depth. Therefore, the fracture-resistant capability of overmatched weld is better than that of undermatched weld. when the toughness of weld metals is similar for both overmatched and undermatched joints.
基金supported by the Key Foundation of Institute of Seismology,China Earthquake Administration( IS200916004)
文摘Yushu Ms7.1 earthquake occurred on the Ganzi-Yushu fault zone, across which we carried out a joint relative-gravity and seismic-reflection survey, and then performed a gravity inversion constrained by the seismic-reflection result. Based on the data of complete Bouguer gravity anomaly and seismic reflection, we obtained a layered interface structure in deep crust down to Moho. Our study showed that the inversion could reveal the interfaces of strata along the survey profile and the directions of regional faults in two-dimension. From the characteristics of the observed topography of the Moho basement, we tentatively confirmed that the uplift of eastern edge of Qinghai-Tibet plateau was caused by the subduetion of the Indian plate.
基金The Program for New Century Excellent Talents in University ( No. NCET-06-0649)the Natural Science Foundation of Hubei Province (No.2005ABA303)
文摘Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided into three zones, including elastic zone, plastic damage zone and shear fracture zone for assessing the stability of the tunnel surrounding rock. By local hydrogeology, the stresses of surrounding rock of Jinshazhou circular tunnel was analyzed and the stress solutions on the elastic and plastic damage zones were obtained by applying the theories of fluid-solid coupling and elasto-plastic damage mechanics. The shear fracture zone generated by joints was studied and its range was determined by using Molar-Coulomb strength criterion. Finally, the correctness of the theoretical results was validated by comparing the scopes of shear fracture zones calculated in this paper with those from literature.
文摘This is a field report on a comprehensive study of the Atamir Formation from the engineering geology perspective using the related indices. The Atamir Formation of the Cretaceous Period, which has outcropped in the form of thick frequencies of grey-knotted sandstone and black shales, is situated in the Kope Dagh zone. A survey of discontinuities together with bedding was carried out to study slope stability. The layers have a general east-west trend with a gentle slope towards the south. Because of the tectonic and stratigraphic differences, and with the purpose of facilitating surveys related to joint study of the outcrop, the formation in the study region was divided into three units. The lower unit is made of shale, the middle of sandstone, and the upper of marlstone. All three units were studied from the perspective of geomechanical classification, rock mass indices, geological strength, geomechanical indices, and wedge instability analysis under dry and wet conditions, and the results were investigated in the form of various images and figures. The Dips software was used to display the rose diagram and stereographic projection of each unit, the Swedge software to analyze instability of the wedges, and the Roctab software to analyze the geomechanical parameters and present the outputs along with the description of each unit.
文摘High chromium （9-12% Cr） steels with excellent heat resistance and CrMoV steels with good toughness were potential candidates for combined rotor for steam turbine operated over 620℃. Two welding techniques were used to fabricate 9% Cr and CrMoV dissimilar welded joint. The results show that the carbon migration only appears in the specimen using narrow gap submerged arc welding （NG-SAW） technique, yet it can be effectively prevented by adding tungsten inert gas （TlG） overlaying process before the NG-SAW. The carbon migration occurred in NG-SAW resulting from the sharp transition of the strong carbide-forming element Cr between the weld （-2.7 wt%） and the base metal （- 9 wt%）. On the contrary, the application of TIG overlaying layers can promote the diffusion of Cr element, and therefore result in its much smaller concentration gradient. That is to say, a gentle transition zone of Cr element can be created among the SAW weld, TIG overlaying layers and the base metal, which effectively prevents the carbon migration and therefore produces a decreased carbon concentration adjacent to the fusion line.
