Reservoirs with a group of vertical fractures in a vertical transversely isotropic(VTI)background are considered as orthorhombic(ORT)medium.However,fracture detection in ORT medium using seismic inversion methods rema...Reservoirs with a group of vertical fractures in a vertical transversely isotropic(VTI)background are considered as orthorhombic(ORT)medium.However,fracture detection in ORT medium using seismic inversion methods remains challenging,as it requires the estimation of more than eight parameters.Assuming the reservoir to be a weakly anisotropic ORT medium with small contrasts in the background elastic parameters,a new azimuthal elastic impedance equation was first derived using parameter combinations and mathematical approximations.This equation exhibited almost the same accuracy as the original equation and contained only six model parameters:the compression modulus,anisotropic shear modulus,anisotropic compression modulus,density,normal fracture weakness,and tangential fracture weakness.Subsequently,a stepwise inversion method using second-order derivatives of the elastic impedance was developed to estimate these parameters.Moreover,the Thomsen anisotropy parameter,epsilon,was estimated from the inversion results using the ratio of the anisotropic compression modulus to the compression modulus.Synthetic examples with moderate noise and field data examples confirm the feasibility and effectiveness of the inversion method.The proposed method exhibited accuracy similar to that of previous inversion strategies and could predict richer vertical fracture information.Ultimately,the method was applied to a three-dimensional work area,and the predictions were consistent with logging and geological a priori information,confirming the effectiveness of this method.Summarily,the proposed stepwise inversion method can alleviate the uncertainty of multi-parameter inversion in ORT medium,thereby improving the reliability of fracture detection.展开更多
The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian componen...The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian component.To obtain higher accuracy and resolution of ocean gravity information,researchers have proposed a novel altimeter called the wide-swath altimeter.This altimeter allows for the simultaneous acquisition of high-precision and high-resolution two-dimensional measurements of sea surface height(SSH).In this paper,the Surface Water and Ocean Topography(SWOT)mission with a wide-swath altimeter on board is selected for research.One cycle of swoT sea surface height data is simulated to inverse the DOV in the Arabian Sea(45°E—80°E,0°-30°N),and the inversion results are compared with those of conventional altimeter data.The results demonstrate that the difference between the meridian and prime components derived from the inversion of swoT wide-swath data is minimal,significantly outperforming the inversion results of conventional nadir altimeter data.The advantage of swoT wide-swath altimeter lies in its ability to use the multi-directional geoid slope at any sea surface measurement point to invert the components in the meridian and prime directions.To investigate the impact of this advantage on inversion precision,this paper employs a method to calculate the gradient of the geoid in multiple directions to invert DoV components.The improvement effect of calculating the gradient of the geoid in multiple directions on the precision of DoV component is analyzed.It is found that the accuracy of DoV inversion has significantly improved with the increase of geodetic gradient calculation direction.In addition,the effects of various errors and grid spacing in SwoT wide sea surface height data on the precision of Dov inversion are also analyzed.展开更多
Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, th...Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, the inversion accuracy of the traditional singular value decomposition （SVD） inversion method reduces with a decrease of SNR. In order to enhance the inversion accuracy and improve robustness of the inversion method to the SNR, an improved inversion method, based on damping factor and spectrum component residual correction, is proposed in this study. The numerical inversion results show that the oscillation of the RTS derived from the SVD method increased with a decrease of SNR, which makes it impossible to get accurate inversion components. However, the SNR has little influence on inversion components of the improved method, and the RTS has high inversion accuracy and robustness. Moreover, RTS derived from core sample data is basically in accord with the pore-size distribution curve, and the RTS derived from the actual induced polarization logging data is smooth and continuous, which indicates that the improved method is practicable.展开更多
A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain go...A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain good posterior flow predictions without inversion of geological parameters of reservoir model.This paper presents an improved DSI method to fast predict reservoir state fields(e.g.saturation and pressure profiles)via observed production data.Firstly,a large number of production curves and state data are generated by reservoir model simulation to expand the data space of original DSI.Then,efficient history matching only on the observed production data is carried out via the original DSI to obtain related parameters which reflects the weight of the real reservoir model relative to prior reservoir models.Finally,those parameters are used to predict the oil saturation and pressure profiles of the real reservoir model by combining large amounts of state data of prior reservoir models.Two examples including conventional heterogeneous and unconventional fractured reservoir are implemented to test the performances of predicting saturation and pressure profiles of this improved DSI method.Besides,this method is also tested in a real field and the obtained results show the high computational efficiency and high accuracy of the practical application of this method.展开更多
D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated si...D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization methods)have been proposed successively,but most are limited to numerical simulations.This study focused on the applicability of different inversion methods for NMR logging data of various acquisition sequences,from which the optimal inversion method was selected based on the comparative analysis.First,the two-dimensional NMR logging principle was studied.Then,these inversion methods were studied in detail,and the precision and computational efficiency of CPMG and diffusion editing(DE)sequences obtained from oil-water and gas-water models were compared,respectively.The inversion results and calculation time of truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization were compared and analyzed through numerical simulations.The inversion method was optimized to process SP mode logging data from the MR Scanner instrument.The results showed that the TIST-regularization and LM-norm smoothing methods were more accurate for the CPMG and DE sequence echo trains of the oil-water and gas-water models.However,the LM-norm smoothing method was less time-consuming,making it more suitable for logging data processing.A case study in well A25 showed that the processing results by the LM-norm smoothing method were consistent with GEOLOG software.This demonstrates that the LM-norm smoothing method is applicable in practical NMR logging processing.展开更多
The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential,...The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.展开更多
The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood,...The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood, the Taylor series is not convergent, and therefore, this paper presents the magnetic interface forward and inversion method based on Pade approximation instead of the Taylor series expansion. Compared with the Taylor series, Pade＇s expansion＇s convergence is more stable and its approximation more accurate. Model tests show the validity of the magnetic forward modeling and inversion of Pade approximation proposed in the paper, and when this inversion method is applied to the measured data of the Matagami area in Canada, a stable and reasonable distribution of underground interface is obtained.展开更多
The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral ...The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral equations. The kinetic theory along with the extended principle of corresponding-states has been used to calculate the viscosity and dif- fusion coefficients over a wide range of temperature and composition. Good agreements between calculated and experimental data are obtained.展开更多
In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the pr...In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the previous research on the characteristics of gravity gradient components,we propose a reweighted inversion method to evaluate the influence of single gravity gradient component on the inversion resolution The proposed method only adopts the misfit function of the regularized equation and introduce a depth weighting function to overcome skin effect produced in gravity gradient inversion.A comparison between different inversion results was undertaken to verify the influence of the depth weighting function on the inversion result resolution.To avoid the premise of introducing prior information,we select the depth weighting function based on the sensitivity matrix.The inversion results using the single-prism model and the complex model show that the influence of different components on the resolution of inversion results is different in different directions,however,the inversion results based on two kind of models with adding different levels of random noise are basically consistent with the results of inversion without noises.Finally,the method was applied to real data from the Vinton salt dome,Louisiana,USA.展开更多
The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun R...The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun Reservoir.Through calculated and compared the error of sedimentation rate by homotopy parametric inversion method and genetic inversion calculation method,the results indicate that homotopy parametric inversion method has good stability,calculating speed,and even if the initial selection away from the objective function,the solution still has a good convergence.展开更多
Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained...Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained the site effects of all stations participating in the calculation.We found that the site effect of rock was stabile and about 1.0 from 1.0Hz to 10.0Hz,while the site effect of deposit was high in low frequencies,about 3 ～ 7 from 1.0Hz to 8.0Hz,and the site effect was protuberant at about 5.0Hz,then fell as the frequency increased.The result shows the shape and intensity of station site effects are mainly influenced by the lithology below the station,and possibly also by the local geological structure.展开更多
This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire pattern...This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire patterns indicate that the copper interconnects are a series of curves with continuous variations instead of beelines. The control equation set of the copper interconnects central lines is attained through the Moire inversion method. This work can be extended to inspect the structural defects and provide a reliable support for the interconnects structure fabrication.展开更多
Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain M...Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain Monte Carlo （MCMC） method is proposed in this paper, combining conventional MCMC method based on global optimization with a preconditioned conjugate gradient （PCG） algorithm based on local optimization, so this method does not depend strongly on the initial model. It converges to the global optimum quickly and efficiently on the condition that effi- ciency and stability of inversion are both taken into consid- eration at the same time. The test data verify the feasibility and robustness of the method, and based on this method, we extract the effective pore-fluid bulk modulus, which is applied to reservoir fluid identification and detection, and consequently, a better result has been achieved.展开更多
Due to the heterogeneity of rock masses and the variability of in situ stress,the traditional linear inversion method is insufficiently accurate to achieve high accuracy of the in situ stress field.To address this cha...Due to the heterogeneity of rock masses and the variability of in situ stress,the traditional linear inversion method is insufficiently accurate to achieve high accuracy of the in situ stress field.To address this challenge,nonlinear stress boundaries for a numerical model are determined through regression analysis of a series of nonlinear coefficient matrices,which are derived from the bubbling method.Considering the randomness and flexibility of the bubbling method,a parametric study is conducted to determine recommended ranges for these parameters,including the standard deviation(σb)of bubble radii,the non-uniform coefficient matrix number(λ)for nonlinear stress boundaries,and the number(m)and positions of in situ stress measurement points.A model case study provides a reference for the selection of these parameters.Additionally,when the nonlinear in situ stress inversion method is employed,stress distortion inevitably occurs near model boundaries,aligning with the Saint Venant's principle.Two strategies are proposed accordingly:employing a systematic reduction of nonlinear coefficients to achieve high inversion accuracy while minimizing significant stress distortion,and excluding regions with severe stress distortion near the model edges while utilizing the central part of the model for subsequent simulations.These two strategies have been successfully implemented in the nonlinear in situ stress inversion of the Xincheng Gold Mine and have achieved higher inversion accuracy than the linear method.Specifically,the linear and nonlinear inversion methods yield root mean square errors(RMSE)of 4.15 and 3.2,and inversion relative errors(δAve)of 22.08%and 17.55%,respectively.Therefore,the nonlinear inversion method outperforms the traditional multiple linear regression method,even in the presence of a systematic reduction in the nonlinear stress boundaries.展开更多
Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea...Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.展开更多
The identification of the traction acting on a portion of the surface of an anisotropic solid is very important in structural health monitoring and optimal design of structures. The traction can be determined using in...The identification of the traction acting on a portion of the surface of an anisotropic solid is very important in structural health monitoring and optimal design of structures. The traction can be determined using inverse methods in which displacement or strain measurements are taken at several points on the body. This paper presents an inverse method based on the method of fundamental solutions for the traction identification problem in two-dimensional anisotropic elasticity. The method of fundamental solutions is an efficient boundary-type meshless method widely used for analyzing various problems. Since the problem is linear, the sensitivity analysis is simply performed by solving the corresponding direct problem several times with different loads. The effects of important parameters such as the number of measurement data, the position of the measurement points, the amount of measurement error, and the type of measurement, i.e., displacement or strain, on the results are also investigated. The results obtained show that the presented inverse method is suitable for the problem of traction identification. It can be concluded from the results that the use of strain measurements in the inverse analysis leads to more accurate results than the use of displacement measurements. It is also found that measurement points closer to the boundary with unknown traction provide more reliable solutions. Additionally, it is found that increasing the number of measurement points increases the accuracy of the inverse solution. However, in cases with a large number of measurement points, further increasing the number of measurement data has little effect on the results.展开更多
Long-term responses of floating structures pose a great concern in their design phase. Existing approaches for addressing long-term extreme responses are extremely cumbersome for adoption. This work aims to develop an...Long-term responses of floating structures pose a great concern in their design phase. Existing approaches for addressing long-term extreme responses are extremely cumbersome for adoption. This work aims to develop an approach for the long-term extreme-response analysis of floating structures. A modified gradient-based retrieval algorithm in conjunction with the inverse first-order reliability method(IFORM) is proposed to enable the use of convolution models in long-term extreme analysis of structures with an analytical formula of response amplitude operator(RAO). The proposed algorithm ensures convergence stability and iteration accuracy and exhibits a higher computational efficiency than the traditional backtracking method. However, when the RAO of general offshore structures cannot be analytically expressed, the convolutional integration method fails to function properly. A numerical discretization approach is further proposed for offshore structures in the case when the analytical expression of the RAO is not feasible. Through iterative discretization of environmental contours(ECs) and RAOs, a detailed procedure is proposed to calculate the long-term response extremes of offshore structures. The validity and accuracy of the proposed approach are tested using a floating offshore wind turbine as a numerical example. The long-term extreme heave responses of various return periods are calculated via the IFORM in conjunction with a numerical discretization approach. The environmental data corresponding to N-year structural responses are located inside the ECs, which indicates that the selection of design points directly along the ECs yields conservative design results.展开更多
The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method....The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method. The former usually does not apply to cases with discontinuity in acoustical parameter profiles[1] , whereas the latter usually ignores the contributions made by multiple reflections, resulting in the appearance of pseudo interfaces. However, under certain practical circumstances, the ray method can produce satisfactory results[2,3]. In this paper, at first we use the conception of equitime layer thickness to obtain the pulse response iteration method. The anti-interference capability of this method is poor. In order to improve this capability, we develope the sample iteration method and the sample-averaging iteration method. The sample-averaging iteration method introduces a way of statistical averaging, which can further improve the anti-interference capability.展开更多
A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion...A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion of the least square error in the transmission losses between calculation and measurement. By using the Gauss - Newton iterative approach, the non - linear least square aloqrithm is equivalent to solving a sequence of lineared least square problems. The physical causes of the instability of the inversion problem are discussed and the stability is improved by means of the Levenberg- Marquardt method. Both numerical simulations with noise and experimental results show that the inversion for the bottom reflection loss of small grazing angle has high precision and the certain perturbation in the measured transmission losses does not lead to serious deviation in the inversion result of the bottom reflection loss.展开更多
How to utilize existing flow control mechanisms to make profiled end wall design more flexible,efficient,and physical is a meaningful challenge.This study presents a three-dimensional inverse method for profiled end w...How to utilize existing flow control mechanisms to make profiled end wall design more flexible,efficient,and physical is a meaningful challenge.This study presents a three-dimensional inverse method for profiled end wall design to achieve the application of flow control mechanisms.The predetermined pressure distribution on the end wall is reached by modifying the end wall geometry during flow field calculation.A motion velocity model is derived from the normal momentum equation of the moving no-slip boundary to modify the end wall geometry.A Reynolds-Averaged Navier-Stokes(RANS)solver based on the Semi-Implicit Method for Pressure Linked Equations(SIMPLE)algorithm is adopted to simulate the flow field.Based on the mechanism understanding obtained through numerical optimization results,this study adopts the inverse method to redesign an optimized end wall in a compressor cascade.The results indicate that the redesigned end wall exhibits better loss reduction,reducing the overall total pressure loss by 5.5%,whereas the optimized end wall reduces it by 3%.The inverse method allows the imposition of desired influences on the end wall flow without constructing a database,making it highly flexible,efficient,and physical.展开更多
基金sponsorship of the National Natural Science Foundation of China(42430809,42274157,42030103,42404132)the Fund of State Key Laboratory of Deep Oil and Gas,China University of Petroleum(East China)(SKLDOG2024-ZYTS-02)+5 种基金the Postdoctoral Fellowship Program of CPSF(GZB20240850)the Postdoctoral Project of Qingdao(QDBSH20240102082)the Fundamental Research Funds for the Central Universities(24CX07004A,24CX06036A)the CNPC Innovation Fund(2024DQ02-0505,2024DQ02-0136)the Innovation fund project for graduate student of China University of Petroleum(East China)the Fundamental Research Funds for the Central Universities(24CX04002A).
文摘Reservoirs with a group of vertical fractures in a vertical transversely isotropic(VTI)background are considered as orthorhombic(ORT)medium.However,fracture detection in ORT medium using seismic inversion methods remains challenging,as it requires the estimation of more than eight parameters.Assuming the reservoir to be a weakly anisotropic ORT medium with small contrasts in the background elastic parameters,a new azimuthal elastic impedance equation was first derived using parameter combinations and mathematical approximations.This equation exhibited almost the same accuracy as the original equation and contained only six model parameters:the compression modulus,anisotropic shear modulus,anisotropic compression modulus,density,normal fracture weakness,and tangential fracture weakness.Subsequently,a stepwise inversion method using second-order derivatives of the elastic impedance was developed to estimate these parameters.Moreover,the Thomsen anisotropy parameter,epsilon,was estimated from the inversion results using the ratio of the anisotropic compression modulus to the compression modulus.Synthetic examples with moderate noise and field data examples confirm the feasibility and effectiveness of the inversion method.The proposed method exhibited accuracy similar to that of previous inversion strategies and could predict richer vertical fracture information.Ultimately,the method was applied to a three-dimensional work area,and the predictions were consistent with logging and geological a priori information,confirming the effectiveness of this method.Summarily,the proposed stepwise inversion method can alleviate the uncertainty of multi-parameter inversion in ORT medium,thereby improving the reliability of fracture detection.
基金support from the National Natural Science Foundation of China(No.42274006,42192535,42242015).
文摘The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian component.To obtain higher accuracy and resolution of ocean gravity information,researchers have proposed a novel altimeter called the wide-swath altimeter.This altimeter allows for the simultaneous acquisition of high-precision and high-resolution two-dimensional measurements of sea surface height(SSH).In this paper,the Surface Water and Ocean Topography(SWOT)mission with a wide-swath altimeter on board is selected for research.One cycle of swoT sea surface height data is simulated to inverse the DOV in the Arabian Sea(45°E—80°E,0°-30°N),and the inversion results are compared with those of conventional altimeter data.The results demonstrate that the difference between the meridian and prime components derived from the inversion of swoT wide-swath data is minimal,significantly outperforming the inversion results of conventional nadir altimeter data.The advantage of swoT wide-swath altimeter lies in its ability to use the multi-directional geoid slope at any sea surface measurement point to invert the components in the meridian and prime directions.To investigate the impact of this advantage on inversion precision,this paper employs a method to calculate the gradient of the geoid in multiple directions to invert DoV components.The improvement effect of calculating the gradient of the geoid in multiple directions on the precision of DoV component is analyzed.It is found that the accuracy of DoV inversion has significantly improved with the increase of geodetic gradient calculation direction.In addition,the effects of various errors and grid spacing in SwoT wide sea surface height data on the precision of Dov inversion are also analyzed.
基金supported by a project from the Youth Science Foundation of the National Natural Science Foundation of China (11104089)
文摘Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, the inversion accuracy of the traditional singular value decomposition （SVD） inversion method reduces with a decrease of SNR. In order to enhance the inversion accuracy and improve robustness of the inversion method to the SNR, an improved inversion method, based on damping factor and spectrum component residual correction, is proposed in this study. The numerical inversion results show that the oscillation of the RTS derived from the SVD method increased with a decrease of SNR, which makes it impossible to get accurate inversion components. However, the SNR has little influence on inversion components of the improved method, and the RTS has high inversion accuracy and robustness. Moreover, RTS derived from core sample data is basically in accord with the pore-size distribution curve, and the RTS derived from the actual induced polarization logging data is smooth and continuous, which indicates that the improved method is practicable.
基金supported by Southern Marine Science and Engineering Guangdong Laboratory(Zhanjiang)(No.ZJW-2019-04)Cooperative Innovation Center of Unconventional Oil and Gas(Ministry of Education&Hubei Province),Yangtze University(No.UOG2020-17)the National Natural Science Foundation of China(No.51874044,51922007)。
文摘A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain good posterior flow predictions without inversion of geological parameters of reservoir model.This paper presents an improved DSI method to fast predict reservoir state fields(e.g.saturation and pressure profiles)via observed production data.Firstly,a large number of production curves and state data are generated by reservoir model simulation to expand the data space of original DSI.Then,efficient history matching only on the observed production data is carried out via the original DSI to obtain related parameters which reflects the weight of the real reservoir model relative to prior reservoir models.Finally,those parameters are used to predict the oil saturation and pressure profiles of the real reservoir model by combining large amounts of state data of prior reservoir models.Two examples including conventional heterogeneous and unconventional fractured reservoir are implemented to test the performances of predicting saturation and pressure profiles of this improved DSI method.Besides,this method is also tested in a real field and the obtained results show the high computational efficiency and high accuracy of the practical application of this method.
基金sponsored by the National Natural Science Foundation of China(Nos.42174149,41774144)the National Major Projects(No.2016ZX05014-001).
文摘D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization methods)have been proposed successively,but most are limited to numerical simulations.This study focused on the applicability of different inversion methods for NMR logging data of various acquisition sequences,from which the optimal inversion method was selected based on the comparative analysis.First,the two-dimensional NMR logging principle was studied.Then,these inversion methods were studied in detail,and the precision and computational efficiency of CPMG and diffusion editing(DE)sequences obtained from oil-water and gas-water models were compared,respectively.The inversion results and calculation time of truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization were compared and analyzed through numerical simulations.The inversion method was optimized to process SP mode logging data from the MR Scanner instrument.The results showed that the TIST-regularization and LM-norm smoothing methods were more accurate for the CPMG and DE sequence echo trains of the oil-water and gas-water models.However,the LM-norm smoothing method was less time-consuming,making it more suitable for logging data processing.A case study in well A25 showed that the processing results by the LM-norm smoothing method were consistent with GEOLOG software.This demonstrates that the LM-norm smoothing method is applicable in practical NMR logging processing.
基金supported by the National Natural Science Foundation of China (Grant No. 51006083)the China Postdoctoral Science Foundation (Grant No. 20110491658)the Fundamental Research Funds for the Central Universities
文摘The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.
基金supported by Sino Probe-09-01-Integrated geophysical data processing and integrated system for moving platform(No.201311192)Graduate innovation fund of Jilin University(No.2015025)
文摘The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood, the Taylor series is not convergent, and therefore, this paper presents the magnetic interface forward and inversion method based on Pade approximation instead of the Taylor series expansion. Compared with the Taylor series, Pade＇s expansion＇s convergence is more stable and its approximation more accurate. Model tests show the validity of the magnetic forward modeling and inversion of Pade approximation proposed in the paper, and when this inversion method is applied to the measured data of the Matagami area in Canada, a stable and reasonable distribution of underground interface is obtained.
文摘The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral equations. The kinetic theory along with the extended principle of corresponding-states has been used to calculate the viscosity and dif- fusion coefficients over a wide range of temperature and composition. Good agreements between calculated and experimental data are obtained.
基金supported by the National Key R&D Program of China(Nos.2016YFC0303002 and 2017YFC0601701)China Geological Survey Program(No.DD20191007)
文摘In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the previous research on the characteristics of gravity gradient components,we propose a reweighted inversion method to evaluate the influence of single gravity gradient component on the inversion resolution The proposed method only adopts the misfit function of the regularized equation and introduce a depth weighting function to overcome skin effect produced in gravity gradient inversion.A comparison between different inversion results was undertaken to verify the influence of the depth weighting function on the inversion result resolution.To avoid the premise of introducing prior information,we select the depth weighting function based on the sensitivity matrix.The inversion results using the single-prism model and the complex model show that the influence of different components on the resolution of inversion results is different in different directions,however,the inversion results based on two kind of models with adding different levels of random noise are basically consistent with the results of inversion without noises.Finally,the method was applied to real data from the Vinton salt dome,Louisiana,USA.
文摘The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun Reservoir.Through calculated and compared the error of sedimentation rate by homotopy parametric inversion method and genetic inversion calculation method,the results indicate that homotopy parametric inversion method has good stability,calculating speed,and even if the initial selection away from the objective function,the solution still has a good convergence.
基金sponsored by the Special Foundation of China Earthquake Administration (2007-8-26)
文摘Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained the site effects of all stations participating in the calculation.We found that the site effect of rock was stabile and about 1.0 from 1.0Hz to 10.0Hz,while the site effect of deposit was high in low frequencies,about 3 ～ 7 from 1.0Hz to 8.0Hz,and the site effect was protuberant at about 5.0Hz,then fell as the frequency increased.The result shows the shape and intensity of station site effects are mainly influenced by the lithology below the station,and possibly also by the local geological structure.
基金supported by the JSPS Postdoctoral Fellowship for Foreign Researchersthe National Basic Research Program of China ("973" Project) (2010CB631005,2011CB606105)+1 种基金the National Natural Science Foundation of China (11172151,90916010)Specialized Research Fund for the Doctoral Program of Higher Education(20090002110048)
文摘This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire patterns indicate that the copper interconnects are a series of curves with continuous variations instead of beelines. The control equation set of the copper interconnects central lines is attained through the Moire inversion method. This work can be extended to inspect the structural defects and provide a reliable support for the interconnects structure fabrication.
基金the sponsorship of the National Basic Research Program of China (973 Program,2013CB228604,2014CB239201)the National Oil and Gas Major Projects of China (2011ZX05014-001-010HZ,2011ZX05014-001-006-XY570) for their funding of this research
文摘Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain Monte Carlo （MCMC） method is proposed in this paper, combining conventional MCMC method based on global optimization with a preconditioned conjugate gradient （PCG） algorithm based on local optimization, so this method does not depend strongly on the initial model. It converges to the global optimum quickly and efficiently on the condition that effi- ciency and stability of inversion are both taken into consid- eration at the same time. The test data verify the feasibility and robustness of the method, and based on this method, we extract the effective pore-fluid bulk modulus, which is applied to reservoir fluid identification and detection, and consequently, a better result has been achieved.
基金funded by the National Key R&D Program of China(Grant No.2022YFC2903904)the National Natural Science Foundation of China(Grant Nos.51904057 and U1906208).
文摘Due to the heterogeneity of rock masses and the variability of in situ stress,the traditional linear inversion method is insufficiently accurate to achieve high accuracy of the in situ stress field.To address this challenge,nonlinear stress boundaries for a numerical model are determined through regression analysis of a series of nonlinear coefficient matrices,which are derived from the bubbling method.Considering the randomness and flexibility of the bubbling method,a parametric study is conducted to determine recommended ranges for these parameters,including the standard deviation(σb)of bubble radii,the non-uniform coefficient matrix number(λ)for nonlinear stress boundaries,and the number(m)and positions of in situ stress measurement points.A model case study provides a reference for the selection of these parameters.Additionally,when the nonlinear in situ stress inversion method is employed,stress distortion inevitably occurs near model boundaries,aligning with the Saint Venant's principle.Two strategies are proposed accordingly:employing a systematic reduction of nonlinear coefficients to achieve high inversion accuracy while minimizing significant stress distortion,and excluding regions with severe stress distortion near the model edges while utilizing the central part of the model for subsequent simulations.These two strategies have been successfully implemented in the nonlinear in situ stress inversion of the Xincheng Gold Mine and have achieved higher inversion accuracy than the linear method.Specifically,the linear and nonlinear inversion methods yield root mean square errors(RMSE)of 4.15 and 3.2,and inversion relative errors(δAve)of 22.08%and 17.55%,respectively.Therefore,the nonlinear inversion method outperforms the traditional multiple linear regression method,even in the presence of a systematic reduction in the nonlinear stress boundaries.
基金The project supported by Key Laboratory of Space Ocean Remote Sensing and Application,Ministry of Natural Resources under contract No.2023CFO016the National Natural Science Foundation of China under contract No.61931025+1 种基金the Innovation Fund Project for Graduate Student of China University of Petroleum(East China)the Fundamental Research Funds for the Central Universities under contract No.23CX04042A.
文摘Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.
基金funded by Vice Chancellor of Research at Shiraz University(grant 3GFU2M1820).
文摘The identification of the traction acting on a portion of the surface of an anisotropic solid is very important in structural health monitoring and optimal design of structures. The traction can be determined using inverse methods in which displacement or strain measurements are taken at several points on the body. This paper presents an inverse method based on the method of fundamental solutions for the traction identification problem in two-dimensional anisotropic elasticity. The method of fundamental solutions is an efficient boundary-type meshless method widely used for analyzing various problems. Since the problem is linear, the sensitivity analysis is simply performed by solving the corresponding direct problem several times with different loads. The effects of important parameters such as the number of measurement data, the position of the measurement points, the amount of measurement error, and the type of measurement, i.e., displacement or strain, on the results are also investigated. The results obtained show that the presented inverse method is suitable for the problem of traction identification. It can be concluded from the results that the use of strain measurements in the inverse analysis leads to more accurate results than the use of displacement measurements. It is also found that measurement points closer to the boundary with unknown traction provide more reliable solutions. Additionally, it is found that increasing the number of measurement points increases the accuracy of the inverse solution. However, in cases with a large number of measurement points, further increasing the number of measurement data has little effect on the results.
基金Supported by the National Natural Science Foundation of China (Grant Nos.52088102 and 51879287)National Key Research and Development Program of China (Grant No.2022YFB2602301)。
文摘Long-term responses of floating structures pose a great concern in their design phase. Existing approaches for addressing long-term extreme responses are extremely cumbersome for adoption. This work aims to develop an approach for the long-term extreme-response analysis of floating structures. A modified gradient-based retrieval algorithm in conjunction with the inverse first-order reliability method(IFORM) is proposed to enable the use of convolution models in long-term extreme analysis of structures with an analytical formula of response amplitude operator(RAO). The proposed algorithm ensures convergence stability and iteration accuracy and exhibits a higher computational efficiency than the traditional backtracking method. However, when the RAO of general offshore structures cannot be analytically expressed, the convolutional integration method fails to function properly. A numerical discretization approach is further proposed for offshore structures in the case when the analytical expression of the RAO is not feasible. Through iterative discretization of environmental contours(ECs) and RAOs, a detailed procedure is proposed to calculate the long-term response extremes of offshore structures. The validity and accuracy of the proposed approach are tested using a floating offshore wind turbine as a numerical example. The long-term extreme heave responses of various return periods are calculated via the IFORM in conjunction with a numerical discretization approach. The environmental data corresponding to N-year structural responses are located inside the ECs, which indicates that the selection of design points directly along the ECs yields conservative design results.
文摘The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method. The former usually does not apply to cases with discontinuity in acoustical parameter profiles[1] , whereas the latter usually ignores the contributions made by multiple reflections, resulting in the appearance of pseudo interfaces. However, under certain practical circumstances, the ray method can produce satisfactory results[2,3]. In this paper, at first we use the conception of equitime layer thickness to obtain the pulse response iteration method. The anti-interference capability of this method is poor. In order to improve this capability, we develope the sample iteration method and the sample-averaging iteration method. The sample-averaging iteration method introduces a way of statistical averaging, which can further improve the anti-interference capability.
基金The Project Supported by National Natural Science Fundation of China
文摘A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion of the least square error in the transmission losses between calculation and measurement. By using the Gauss - Newton iterative approach, the non - linear least square aloqrithm is equivalent to solving a sequence of lineared least square problems. The physical causes of the instability of the inversion problem are discussed and the stability is improved by means of the Levenberg- Marquardt method. Both numerical simulations with noise and experimental results show that the inversion for the bottom reflection loss of small grazing angle has high precision and the certain perturbation in the measured transmission losses does not lead to serious deviation in the inversion result of the bottom reflection loss.
基金Supported by the National Natural Science Foundation of China(No.52376021).
文摘How to utilize existing flow control mechanisms to make profiled end wall design more flexible,efficient,and physical is a meaningful challenge.This study presents a three-dimensional inverse method for profiled end wall design to achieve the application of flow control mechanisms.The predetermined pressure distribution on the end wall is reached by modifying the end wall geometry during flow field calculation.A motion velocity model is derived from the normal momentum equation of the moving no-slip boundary to modify the end wall geometry.A Reynolds-Averaged Navier-Stokes(RANS)solver based on the Semi-Implicit Method for Pressure Linked Equations(SIMPLE)algorithm is adopted to simulate the flow field.Based on the mechanism understanding obtained through numerical optimization results,this study adopts the inverse method to redesign an optimized end wall in a compressor cascade.The results indicate that the redesigned end wall exhibits better loss reduction,reducing the overall total pressure loss by 5.5%,whereas the optimized end wall reduces it by 3%.The inverse method allows the imposition of desired influences on the end wall flow without constructing a database,making it highly flexible,efficient,and physical.
