Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites wa...Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites was characterized by transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. The selected area electron diffraction （SAED） for the interface was investigated. The elements at the interface were scanned by energy dispersive spectroscopy （EDS） and the EDS mapping was also obtained. X-ray diffraction （XRD） analysis was carried out for the composites fabricated by 1 pass, 2 passes and 4 passes ECAP-T. According to the XRD analysis, the influences of ECAP-T pass on the Bragg angle and interplanar spacing for AI crystalline planes were studied. The results show that after ECAP-T, the interface between A1 and SiC within the composites is a belt of amorphous SiO2 containing a trace of A1, Si and C which diffused from the matrix and the reinforcement. With the growing ECAP-T pass, the Bragg angle decreases and interplanar spacing increases for A1 crystalline planes, due to the accumulated lattice strain. The increasing lattice strain of A1 grains also boosts the density of the dislocation within A1 grains.展开更多
Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shear...Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shearing dislocation.Using digital image techno-logy and three-dimensional(3D)laser morphology scanning techniques,a set of 3D models with rough joint surfaces was established.Further,the mechanical behavior of rock–backfill shearing dislocation was investigated using a direct shear test.The effects of interface roughness on the shear–displacement curve and failure characteristics of rock–backfill specimens were considered.The 3D fractal dimen-sion,profile line joint roughness coefficient(JRC),profile line two-dimensional fractal dimension,and the surface curvature of the frac-tures were obtained.The correlation characterization of surface roughness was then analyzed,and the shear strength could be measured and calculated using JRC.The results showed the following:there were three failure threshold value points in rock–backfill shearing dis-location:30%–50%displacement before the peak,70%–90%displacement before the peak,and 100%displacement before the peak to post-peak,which could be a sign for rock–backfill shearing dislocation failure.The surface JRC could be used to judge the rock–backfill shearing dislocation failure,including post-peak sliding,uniform variations,and gradient change,corresponding to rock–backfill disloca-tion failure on the field site.The research reveals the damage mechanism for rock–backfill complexes based on the free joint surface,fills the gap of existing shearing theoretical systems for isomerism complexes,and provides a theoretical basis for the prevention and control of possible disasters in backfill mining.展开更多
Interaction between a screw dislocation dipole and a mode III interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocati...Interaction between a screw dislocation dipole and a mode III interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocation dipole lies inside a medium. The stress fields and the stress intensity factors at the tip of the interface crack produced by the screw dislocation dipole are given. The influence of the orientation, the dipole arm and the location of the screw dislocation dipole as well as the material mismatch on the stress intensity factors is discussed. The image force and the image torque acting on the screw dislocation dipole center are also calculated. The mechanical equilibrium position of the screw dislocation dipole is examined for various material property combinations and crack geometries. The results indicate that the shielding or anti-shielding effect on the stress intensity factor increases abruptly when the dislocation dipole approaches the tip of the crack. Additionally, the disturbation of the interface crack on the motion of the dislocation dipole is also significant.展开更多
The inhibitory effect of the second phase on dislocation movement has long been deemed as a great con-tribution to the strengthening of alloys.We investigate the electronic behavior at theα-Al matrix/second phase int...The inhibitory effect of the second phase on dislocation movement has long been deemed as a great con-tribution to the strengthening of alloys.We investigate the electronic behavior at theα-Al matrix/second phase interface to explore its inhibitory effect on dislocation movement.This work focuses on the dif-ficulty in dislocation movement on the interface ofα-Al/Al_(3)Sc,α-Al/θ’(Al_(2)Cu),andα-Al/T_(1)(Al_(2)CuLi)of aluminum-lithium-scandium alloy based on detailed transmission electron microscopy investigation and electron transport calculation.The more drastic the electron transport between two atoms at the inter-face,the more intense the interaction between them,corresponding to the larger difficulty in breaking and forming bonds between them during the movement process of the extra half plane of dislocation on the interface.The calculated difference in density of valence electrons and differential charge density atα-Al/second phase interface reveals that Al_(3)Sc is characterized by the largest resistance to dislocation movement compared toθ’(Al_(2)Cu)and T_(1)(Al_(2)CuLi).The large differential charge density between the in-terface of(100)Al_(3)Sc/(100)Al demonstrates the strong bonds betweenα-Al and Al_(3)Sc and the large difficulty for the extra half plane of dislocation to form or break bonds during the movement process atα-Al/Al_(3)Sc interface.The dislocation pile-up indicates a discernible hindering effect of theα-Al/Al_(3)Sc interface on dislocation movement.The hindering effect presented byα-Al/Al_(3)Sc interface is favorable for the tensile strength.展开更多
Stresses in epitaxial and textured Al films were determined by substrate-curvature measurements. It was found that in both cases the flow stresses increase with decreasing film thickness. The flow stresses in the epit...Stresses in epitaxial and textured Al films were determined by substrate-curvature measurements. It was found that in both cases the flow stresses increase with decreasing film thickness. The flow stresses in the epitaxial Al films are in agreement with a dislocation-based model, while the same model strongly underestimates the flow stresses of textured Al films. In-situ transmission electron microscopy studies indicate that dislocations channeling through epitaxial Al films on single-crystalline (0001) α-AI2O3 substrates frequently deposit dislocation segments adjacent to the interface. Furthermore, the AI/α-AI2O3 interface acted as a dislocation source. In this case, the interface is between two crystalline lattices. In contrast, the interface of textured Al films on oxidized silicon substrates is between the crystalline Al and the amorphous SiOx interlayer. It is speculated that the different nature of the interfaces changes dislocation mechanisms and thus influences the flow stresses.展开更多
Nanolayered Cu-Nb composites offer a series of enhanced properties for their use in extreme conditions, e.g. high field magnets and high irradiation resistance. However, the stability of the Cu/Nb heterogeneous interf...Nanolayered Cu-Nb composites offer a series of enhanced properties for their use in extreme conditions, e.g. high field magnets and high irradiation resistance. However, the stability of the Cu/Nb heterogeneous interface needs confirmation under various conditions. In the present work, molecular dynamics simulations were carried out to investigate the interracial behavior under various temperatures with initial stress at the interface. It is found that the interface becomes unstable at simulation temperatures higher than O00 K, resulting in the emission of dislocations and loops within one or more slip systems. The emission process is Found to be thermally-activated, i.e., the higher temperature, the shorter annealing time needed. The present study is believed to assist the experimental synthesis of the Cu-Nb multilayer nanocomposites For multiple applications.展开更多
Interracial dislocation may have a spreading core corresponding to a weak shear resistance of interfaces. In this paper, a conic model is proposed to mimic the spreading core of interfacial dislocation in anisotropic ...Interracial dislocation may have a spreading core corresponding to a weak shear resistance of interfaces. In this paper, a conic model is proposed to mimic the spreading core of interfacial dislocation in anisotropic bimaterials. By the Stroh formalism and Green＇s function, the analytical expressions of the elastic fields are deduced for such a dislocation. Taking Cu/Nb bimaterial as an example, it is demonstrated that the accuracy and efficiency of the method are well validated by the interface conditions, a spreading core can greatly reduce the stress intensity near the interfacial dislocation compared with the compact core, and the elastic fields near the spreading core region are significantly different from the condensed core, while they are less sensitive to a field point that is 1.5 times the core width away from the center of the spreading core.展开更多
The problem of a screw dislocation interacting with a circular nano-inhomogeneity near a bimaterial interface is investigated. The stress boundary condition at the interface between the inhomogeneity and the matrix is...The problem of a screw dislocation interacting with a circular nano-inhomogeneity near a bimaterial interface is investigated. The stress boundary condition at the interface between the inhomogeneity and the matrix is modified by incorporating surface/interface stress. The analytical solutions to the problem in explicit series are obtained by an efficient complex variable method associated with the conformal mapping function. The image force exerted on the screw dislocation is also derived using the generalized Peach–Koehler formula. The results indicate that the elastic interference of the screw dislocation and the nano-inhomogeneity is strongly affected by a combination of material elastic dissimilarity, the radius of the inclusion, the distance from the center of inclusion to the bimaterial interface, and the surface/interface stress between the inclusion and the matrix. Additionally, it is found that when the inclusion and Material 3 are both harder than the matrix（ μ1 〉 μ2 and μ3 〉 μ2）, a new stable equilibrium position for the screw dislocation in the matrix appears near the bimaterial interface; when the inclusion and Material 3 are both softer than the matrix（ μ1 〈 μ2 and μ3 〈 μ2）, a new unstable equilibrium position exists close to the bimaterial interface.展开更多
The basic equations of the representation of plasticity at an interface crack by an inclined strip yield superdislocation model are derived. With a special combination of the material properties and small-scale yieldi...The basic equations of the representation of plasticity at an interface crack by an inclined strip yield superdislocation model are derived. With a special combination of the material properties and small-scale yielding case, the problem is reduced to an algebraic equation in an unknown, the ratio of the plastic zone size. Some discussions on the limitations of this model are presented.展开更多
Understanding the interface between strengthening precipitates and matrix in alloys, especially at the atomic level, is a critical issue for tailoring the precipitate strengthening to achieve desired mechanical proper...Understanding the interface between strengthening precipitates and matrix in alloys, especially at the atomic level, is a critical issue for tailoring the precipitate strengthening to achieve desired mechanical properties. Using high-resolution scanning transmission electron microscopy, we here clarify the semicoherent interfaces between the matrix and long-period stacking ordered(LPSO) phases, including 18 R and 14 H, in Mg–Zn–Y alloys. The LPSO/Mg interface features the unique configuration of the Shockley partial dislocations, which produces a near zero macroscopic strain because the net Burgers vectors equal zero. The 18 R/Mg interface characterizes a dissociated structure that can be described as a narrow slab of 54 R. There are two dislocation arrays accompanied to the 18 R/54 R and 54 R/Mg interface, resulting a slight deviation(about 2.3°). The 14 R/Mg interface exhibits the dislocation pairs associated with solute atoms. We further evaluate the stability and morphology of the corresponding interfaces based on elastic interaction, via calculating the mutual strong interactions between dislocation arrays, as well as that between the dislocations and solute atoms. The synchronized migration of interfacial dislocations and solute atoms, like move-drag behavior, dominates the lateral growth of LPSO phases in Mg alloys.展开更多
Interface dislocations may dramatically change the electric properties, such as polarization, of the piezoelectric crystals. In this paper, we study the linear interactions of two interface dislocation loops with arbi...Interface dislocations may dramatically change the electric properties, such as polarization, of the piezoelectric crystals. In this paper, we study the linear interactions of two interface dislocation loops with arbitrary shape in generally anisotropic piezoelectric bi-crystals. A simple formula for calculating the interaction energy of the interface dislocation loops is derived and given by a double line integral along two closed dislocation curves. Particularly, interactions between two straight segments of the interface dislocations are solved analytically, which can be applied to approximate any curved loop so that an analytical solution can be also achieved. Numerical results show the influence of the bi-crystal interface as well as the material orientation on the interaction of interface dislocation loops.展开更多
Interface imperfection can significantly affect the mechanical properties and failure mechanisms as well as the strength and toughness of nanocomposites. The elastic behavior of a screw dislocation in nanoscale coatin...Interface imperfection can significantly affect the mechanical properties and failure mechanisms as well as the strength and toughness of nanocomposites. The elastic behavior of a screw dislocation in nanoscale coating with imperfect interface is studied in the three-phase composite cylinder model. The interface between inner nanoin- homogeneity and intermediate coating is assumed as perfectly bonded. The bonding between intermediate coating and outer matrix is considered to be imperfect with the assumption that interface imperfection is uniform, and a linear spring model is adopted to describe the weakness of imperfect interface. The explicit expression for image force acting on dislocation is obtained by means of a complex variable method. The analytic results indicate that inner interface effect and outer interface imperfection, simultaneously taken into account, would influence greatly image force, equilibrium position and stability of dislocation, and various critical parameters that would change dislocation stability. The weaker interface is a very strong trap for glide dislocation and, thus, a more effective barrier for slip transmission.展开更多
The contribution to the critical shear stress of nanocomposites caused by the interaction between screw dislocations and core-shell nanowires (coated nanowires) with interface stresses was derived by means of the MOTT...The contribution to the critical shear stress of nanocomposites caused by the interaction between screw dislocations and core-shell nanowires (coated nanowires) with interface stresses was derived by means of the MOTT and NABARRO's model. The influence of interface stresses on the critical shear stress was examined. The result indicates that, if the volume fraction of the core-shell nanowires keeps a constant, an optimal critical shear stress may be obtained when the radius of the nanowire with interface stresses reaches a critical value, which differs from the classical solution without considering the interface stresses under the same external conditions. In addition, the material may be strengthened by the soft nanowires when the interface stresses are considered. There also exist critical values of the elastic modulus and the thickness of surface coating to alter the strengthening effect produced by it.展开更多
Faceted interphase boundaries(IPBs)are commonly observed in lath-shaped precipitates in alloys consisting of simple face-centred cubic(fcc),body centred-cubic(bcc)or hexagonal closed packed(hcp)phases,which normally c...Faceted interphase boundaries(IPBs)are commonly observed in lath-shaped precipitates in alloys consisting of simple face-centred cubic(fcc),body centred-cubic(bcc)or hexagonal closed packed(hcp)phases,which normally contain one or two sets of parallel dislocations.The influence of these dislocations on interface migration and possible accompanying long-range strain field remain unclear.To elucidate this,we carried out atomistic simulations to investigate the dislocation-mediated migration processes of IPBs in a pure-iron system.Our results show that the migration of these IPBs is accompanied with the slip of interfacial dislocations,even in high-index slip planes,with two migration modes were observed:the first mode is the uniform migration mode that occurs only when all of the dislocations slip in a common slip plane.A shear-coupled interface migration was observed for this mode.The other interfaces propagate in the stick-slip migration mode that occurs when the dislocations glide on different slip planes,involving dislocation reaction or tangling.A quantitative relationship was established to link the atomic displacements with the dislocation structure,slip plane,and interface normal.The macroscopic shear deformation due to the effect of overall atomic displacement shows a good agreement with the results obtained based on the phenomenological theory of martensite crystallography.Our findings have general implications for the understanding of phase transformations and the surface relief effect at the atomic scale.展开更多
The image stress of straight screw dislocations parallel to the medium surface covered by thin heterogeneous films was analyzed and deduced, in order to calculate the image shear stress. The relationship between image...The image stress of straight screw dislocations parallel to the medium surface covered by thin heterogeneous films was analyzed and deduced, in order to calculate the image shear stress. The relationship between image stress and distance from the screw dislocation to the interface of pure aluminum and its oxide covering was calculated based on the analysis. It was shown quantitatively that a sign conversion of the image stress appears in the case of thin oxide covering, while dislocation would pile up near the interface because of the possible slips of the screw dislocations induced by the image stress, which might break down the very thin oxide covering. Further investigation on edge dislocations or other dislocation configurations need to be done.展开更多
α/β(hcp/bcc)interfaces are of great importance in the microstructure development and the mechanical properties of titanium and zirconium alloys.This work contributes to the study of interface energetics and interfac...α/β(hcp/bcc)interfaces are of great importance in the microstructure development and the mechanical properties of titanium and zirconium alloys.This work contributes to the study of interface energetics and interfacial structures of the precipitate in the hcp/bcc system based on a simulation study using molecular statics(MS)and molecular dynamics(MD).The input orientation relationship(OR)was calculated based on the O-line criterion.Based on the energy of the interfaces containing the invariant line(IL),two preferred facets were determined by the Wulff construction,which explained the observed orientations of the habit plane(HP)and the side facet(SF).The deviation of the observed precipitate morphology from the equilibrium shape was discussed in terms of interface kinetics.The structures of the interfaces surrounding a three-dimensional(3 D)precipitate,including the preferred facets and the end face,were obtained at the atomic level.The simulated dislocation structures and atomic structures in these interfaces are in good agreement with those of the experimental observations for Ti-Cr alloys.A method was suggested for modifying the O-cell structure with the guidance of the relaxed structure,yielding consistency between the calculated dislocation structure based on the generalized O-element approach and the simulation results.展开更多
Nd:YAG crystals free from core and dislocation have been grown by using the“controlled reversion of solid-liquid interface” method.The basic idea of the method is to combine the respective advantages of both the con...Nd:YAG crystals free from core and dislocation have been grown by using the“controlled reversion of solid-liquid interface” method.The basic idea of the method is to combine the respective advantages of both the convex and the flat interface growth and to overpass "safely"the interface reversion so that the whole crystal could be grown in stable fluid How states.展开更多
This paper attempts to explore the functional divergence of LD （Left Dislocation） in English and Chinese. Through detailed analyzing, we find that LD in both languages shares only one function, the function of simpl...This paper attempts to explore the functional divergence of LD （Left Dislocation） in English and Chinese. Through detailed analyzing, we find that LD in both languages shares only one function, the function of simplifying, but it is different in other functions and there are eight more functions in Chinese than in English. The interface study of LD in the two languages leads to the implications： The connections between syntactic form and discourse function are language-specific and arbitrary, and LD serves a wide variety of discourse functions and is motivated by a range of discourse circumstances展开更多
Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was s...Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.展开更多
Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in ...Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in this paper under certain conditions. It demonstrates that the influence of the α/β interface phase on the tensile properties is closely associated with dislocations and twin substructure through comparison experiments. The results show that the α/β interface phase hinders dislocation motion and decreases effective slip length. In addition, the twin substructure has been activated in the α/β interface phase during tensile process and has acted somehow like grain boundaries. Therefore, the strength and the work-hardening rate of the laser cladding deposited Ti-6Al-4V titanium alloy have been significantly improved due to the dynamic Hall-Petch effect. Besides, the α/β interface phase leads to more uniform dislocations distribution, which implies that relative lower local concentrated stress will be produced along the α/β interface phase or colony boundary after the same amount of plastic deformation. Moreover,the twinning-induced plasticity effects in the α/β interface phase further increase the plastic deformation capacity. These results in higher elongation for the laser cladding deposited Ti-6Al-4V titanium alloy.It can be concluded that the current work suggests an effective method to simultaneously improve the strength and plasticity of laser cladding deposited Ti-6Al-4V titanium alloy based on the α/β interface phase.展开更多
基金Project(51175138) supported by the National Natural Science Foundation of ChinaProjects(2012HGZX0030,2013HGCH0011) supported by the Fundamental Research Funds for the Central Universities,China
文摘Powder mixture of pure A1 and oxidized SiC was consolidated into 10% （mass fraction） SiCp/AI composites at 523 K by equal channel angular pressing and torsion （ECAP-T）. The interfacial bonding of the composites was characterized by transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. The selected area electron diffraction （SAED） for the interface was investigated. The elements at the interface were scanned by energy dispersive spectroscopy （EDS） and the EDS mapping was also obtained. X-ray diffraction （XRD） analysis was carried out for the composites fabricated by 1 pass, 2 passes and 4 passes ECAP-T. According to the XRD analysis, the influences of ECAP-T pass on the Bragg angle and interplanar spacing for AI crystalline planes were studied. The results show that after ECAP-T, the interface between A1 and SiC within the composites is a belt of amorphous SiO2 containing a trace of A1, Si and C which diffused from the matrix and the reinforcement. With the growing ECAP-T pass, the Bragg angle decreases and interplanar spacing increases for A1 crystalline planes, due to the accumulated lattice strain. The increasing lattice strain of A1 grains also boosts the density of the dislocation within A1 grains.
基金supported by the National Key Research and Development Program of China(No.2021YFC3001302)the National Natural Science Foundation of China(No.52274072).
文摘Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shearing dislocation.Using digital image techno-logy and three-dimensional(3D)laser morphology scanning techniques,a set of 3D models with rough joint surfaces was established.Further,the mechanical behavior of rock–backfill shearing dislocation was investigated using a direct shear test.The effects of interface roughness on the shear–displacement curve and failure characteristics of rock–backfill specimens were considered.The 3D fractal dimen-sion,profile line joint roughness coefficient(JRC),profile line two-dimensional fractal dimension,and the surface curvature of the frac-tures were obtained.The correlation characterization of surface roughness was then analyzed,and the shear strength could be measured and calculated using JRC.The results showed the following:there were three failure threshold value points in rock–backfill shearing dis-location:30%–50%displacement before the peak,70%–90%displacement before the peak,and 100%displacement before the peak to post-peak,which could be a sign for rock–backfill shearing dislocation failure.The surface JRC could be used to judge the rock–backfill shearing dislocation failure,including post-peak sliding,uniform variations,and gradient change,corresponding to rock–backfill disloca-tion failure on the field site.The research reveals the damage mechanism for rock–backfill complexes based on the free joint surface,fills the gap of existing shearing theoretical systems for isomerism complexes,and provides a theoretical basis for the prevention and control of possible disasters in backfill mining.
基金Project supported by the National Natural Science Foundation of China (No. 10472030).
文摘Interaction between a screw dislocation dipole and a mode III interface crack is investigated. By using the complex variable method, the closed form solutions for complex potentials are obtained when a screw dislocation dipole lies inside a medium. The stress fields and the stress intensity factors at the tip of the interface crack produced by the screw dislocation dipole are given. The influence of the orientation, the dipole arm and the location of the screw dislocation dipole as well as the material mismatch on the stress intensity factors is discussed. The image force and the image torque acting on the screw dislocation dipole center are also calculated. The mechanical equilibrium position of the screw dislocation dipole is examined for various material property combinations and crack geometries. The results indicate that the shielding or anti-shielding effect on the stress intensity factor increases abruptly when the dislocation dipole approaches the tip of the crack. Additionally, the disturbation of the interface crack on the motion of the dislocation dipole is also significant.
基金This work was financially supported by the National Natural Science Foundation of China(No.51774106).
文摘The inhibitory effect of the second phase on dislocation movement has long been deemed as a great con-tribution to the strengthening of alloys.We investigate the electronic behavior at theα-Al matrix/second phase interface to explore its inhibitory effect on dislocation movement.This work focuses on the dif-ficulty in dislocation movement on the interface ofα-Al/Al_(3)Sc,α-Al/θ’(Al_(2)Cu),andα-Al/T_(1)(Al_(2)CuLi)of aluminum-lithium-scandium alloy based on detailed transmission electron microscopy investigation and electron transport calculation.The more drastic the electron transport between two atoms at the inter-face,the more intense the interaction between them,corresponding to the larger difficulty in breaking and forming bonds between them during the movement process of the extra half plane of dislocation on the interface.The calculated difference in density of valence electrons and differential charge density atα-Al/second phase interface reveals that Al_(3)Sc is characterized by the largest resistance to dislocation movement compared toθ’(Al_(2)Cu)and T_(1)(Al_(2)CuLi).The large differential charge density between the in-terface of(100)Al_(3)Sc/(100)Al demonstrates the strong bonds betweenα-Al and Al_(3)Sc and the large difficulty for the extra half plane of dislocation to form or break bonds during the movement process atα-Al/Al_(3)Sc interface.The dislocation pile-up indicates a discernible hindering effect of theα-Al/Al_(3)Sc interface on dislocation movement.The hindering effect presented byα-Al/Al_(3)Sc interface is favorable for the tensile strength.
文摘Stresses in epitaxial and textured Al films were determined by substrate-curvature measurements. It was found that in both cases the flow stresses increase with decreasing film thickness. The flow stresses in the epitaxial Al films are in agreement with a dislocation-based model, while the same model strongly underestimates the flow stresses of textured Al films. In-situ transmission electron microscopy studies indicate that dislocations channeling through epitaxial Al films on single-crystalline (0001) α-AI2O3 substrates frequently deposit dislocation segments adjacent to the interface. Furthermore, the AI/α-AI2O3 interface acted as a dislocation source. In this case, the interface is between two crystalline lattices. In contrast, the interface of textured Al films on oxidized silicon substrates is between the crystalline Al and the amorphous SiOx interlayer. It is speculated that the different nature of the interfaces changes dislocation mechanisms and thus influences the flow stresses.
文摘Nanolayered Cu-Nb composites offer a series of enhanced properties for their use in extreme conditions, e.g. high field magnets and high irradiation resistance. However, the stability of the Cu/Nb heterogeneous interface needs confirmation under various conditions. In the present work, molecular dynamics simulations were carried out to investigate the interracial behavior under various temperatures with initial stress at the interface. It is found that the interface becomes unstable at simulation temperatures higher than O00 K, resulting in the emission of dislocations and loops within one or more slip systems. The emission process is Found to be thermally-activated, i.e., the higher temperature, the shorter annealing time needed. The present study is believed to assist the experimental synthesis of the Cu-Nb multilayer nanocomposites For multiple applications.
基金Project supported by the National Natural Science Foundation of China(No.11672173)the Shanghai Eastern-Scholar Planthe Innovation Program of Shanghai Municipal Education Commission
文摘Interracial dislocation may have a spreading core corresponding to a weak shear resistance of interfaces. In this paper, a conic model is proposed to mimic the spreading core of interfacial dislocation in anisotropic bimaterials. By the Stroh formalism and Green＇s function, the analytical expressions of the elastic fields are deduced for such a dislocation. Taking Cu/Nb bimaterial as an example, it is demonstrated that the accuracy and efficiency of the method are well validated by the interface conditions, a spreading core can greatly reduce the stress intensity near the interfacial dislocation compared with the compact core, and the elastic fields near the spreading core region are significantly different from the condensed core, while they are less sensitive to a field point that is 1.5 times the core width away from the center of the spreading core.
文摘The problem of a screw dislocation interacting with a circular nano-inhomogeneity near a bimaterial interface is investigated. The stress boundary condition at the interface between the inhomogeneity and the matrix is modified by incorporating surface/interface stress. The analytical solutions to the problem in explicit series are obtained by an efficient complex variable method associated with the conformal mapping function. The image force exerted on the screw dislocation is also derived using the generalized Peach–Koehler formula. The results indicate that the elastic interference of the screw dislocation and the nano-inhomogeneity is strongly affected by a combination of material elastic dissimilarity, the radius of the inclusion, the distance from the center of inclusion to the bimaterial interface, and the surface/interface stress between the inclusion and the matrix. Additionally, it is found that when the inclusion and Material 3 are both harder than the matrix（ μ1 〉 μ2 and μ3 〉 μ2）, a new stable equilibrium position for the screw dislocation in the matrix appears near the bimaterial interface; when the inclusion and Material 3 are both softer than the matrix（ μ1 〈 μ2 and μ3 〈 μ2）, a new unstable equilibrium position exists close to the bimaterial interface.
基金Visiting Research Fellow in Institute of Industrial Science.University of Tokyo,supported by Japan Society for the Promotion of Science.
文摘The basic equations of the representation of plasticity at an interface crack by an inclined strip yield superdislocation model are derived. With a special combination of the material properties and small-scale yielding case, the problem is reduced to an algebraic equation in an unknown, the ratio of the plastic zone size. Some discussions on the limitations of this model are presented.
基金supported financially by the National Natural Science Foundation of China(Nos.51801214 and 51871222)the Liaoning Provincial Natural Science Foundation(No.2019-MS-335)。
文摘Understanding the interface between strengthening precipitates and matrix in alloys, especially at the atomic level, is a critical issue for tailoring the precipitate strengthening to achieve desired mechanical properties. Using high-resolution scanning transmission electron microscopy, we here clarify the semicoherent interfaces between the matrix and long-period stacking ordered(LPSO) phases, including 18 R and 14 H, in Mg–Zn–Y alloys. The LPSO/Mg interface features the unique configuration of the Shockley partial dislocations, which produces a near zero macroscopic strain because the net Burgers vectors equal zero. The 18 R/Mg interface characterizes a dissociated structure that can be described as a narrow slab of 54 R. There are two dislocation arrays accompanied to the 18 R/54 R and 54 R/Mg interface, resulting a slight deviation(about 2.3°). The 14 R/Mg interface exhibits the dislocation pairs associated with solute atoms. We further evaluate the stability and morphology of the corresponding interfaces based on elastic interaction, via calculating the mutual strong interactions between dislocation arrays, as well as that between the dislocations and solute atoms. The synchronized migration of interfacial dislocations and solute atoms, like move-drag behavior, dominates the lateral growth of LPSO phases in Mg alloys.
基金supports from the National Natural Science Foundation of China(11402133 and 11502128)
文摘Interface dislocations may dramatically change the electric properties, such as polarization, of the piezoelectric crystals. In this paper, we study the linear interactions of two interface dislocation loops with arbitrary shape in generally anisotropic piezoelectric bi-crystals. A simple formula for calculating the interaction energy of the interface dislocation loops is derived and given by a double line integral along two closed dislocation curves. Particularly, interactions between two straight segments of the interface dislocations are solved analytically, which can be applied to approximate any curved loop so that an analytical solution can be also achieved. Numerical results show the influence of the bi-crystal interface as well as the material orientation on the interaction of interface dislocation loops.
基金supported by the National Natural Science Foundation of China(11172094 and 11172095)the NCET-11-0122 and Hunan Provincial Natural Science Foundation for Creative Research Groups of China(12JJ7001)
文摘Interface imperfection can significantly affect the mechanical properties and failure mechanisms as well as the strength and toughness of nanocomposites. The elastic behavior of a screw dislocation in nanoscale coating with imperfect interface is studied in the three-phase composite cylinder model. The interface between inner nanoin- homogeneity and intermediate coating is assumed as perfectly bonded. The bonding between intermediate coating and outer matrix is considered to be imperfect with the assumption that interface imperfection is uniform, and a linear spring model is adopted to describe the weakness of imperfect interface. The explicit expression for image force acting on dislocation is obtained by means of a complex variable method. The analytic results indicate that inner interface effect and outer interface imperfection, simultaneously taken into account, would influence greatly image force, equilibrium position and stability of dislocation, and various critical parameters that would change dislocation stability. The weaker interface is a very strong trap for glide dislocation and, thus, a more effective barrier for slip transmission.
基金Projects(50801025, 50634060 ) supported by the National Natural Science Foundation of China
文摘The contribution to the critical shear stress of nanocomposites caused by the interaction between screw dislocations and core-shell nanowires (coated nanowires) with interface stresses was derived by means of the MOTT and NABARRO's model. The influence of interface stresses on the critical shear stress was examined. The result indicates that, if the volume fraction of the core-shell nanowires keeps a constant, an optimal critical shear stress may be obtained when the radius of the nanowire with interface stresses reaches a critical value, which differs from the classical solution without considering the interface stresses under the same external conditions. In addition, the material may be strengthened by the soft nanowires when the interface stresses are considered. There also exist critical values of the elastic modulus and the thickness of surface coating to alter the strengthening effect produced by it.
基金financially supported by the National Natural Science Foundation of China (Nos.51471097 and 51671111)the National Key Research and Development Program of China (No. 2016YFB0701304)
文摘Faceted interphase boundaries(IPBs)are commonly observed in lath-shaped precipitates in alloys consisting of simple face-centred cubic(fcc),body centred-cubic(bcc)or hexagonal closed packed(hcp)phases,which normally contain one or two sets of parallel dislocations.The influence of these dislocations on interface migration and possible accompanying long-range strain field remain unclear.To elucidate this,we carried out atomistic simulations to investigate the dislocation-mediated migration processes of IPBs in a pure-iron system.Our results show that the migration of these IPBs is accompanied with the slip of interfacial dislocations,even in high-index slip planes,with two migration modes were observed:the first mode is the uniform migration mode that occurs only when all of the dislocations slip in a common slip plane.A shear-coupled interface migration was observed for this mode.The other interfaces propagate in the stick-slip migration mode that occurs when the dislocations glide on different slip planes,involving dislocation reaction or tangling.A quantitative relationship was established to link the atomic displacements with the dislocation structure,slip plane,and interface normal.The macroscopic shear deformation due to the effect of overall atomic displacement shows a good agreement with the results obtained based on the phenomenological theory of martensite crystallography.Our findings have general implications for the understanding of phase transformations and the surface relief effect at the atomic scale.
基金The authors wish to thank the financial support given by the National Natural Science Foundation of China(Grant No.50571020)the Doctoral Foundation of the Education Ministry of China(Grant No.20040008010).
文摘The image stress of straight screw dislocations parallel to the medium surface covered by thin heterogeneous films was analyzed and deduced, in order to calculate the image shear stress. The relationship between image stress and distance from the screw dislocation to the interface of pure aluminum and its oxide covering was calculated based on the analysis. It was shown quantitatively that a sign conversion of the image stress appears in the case of thin oxide covering, while dislocation would pile up near the interface because of the possible slips of the screw dislocations induced by the image stress, which might break down the very thin oxide covering. Further investigation on edge dislocations or other dislocation configurations need to be done.
基金Supports from the National Key Research and Development Program of China(Grant No.2016YFB0701304)the National Natural Science Foundation of China(Grant No.51871131)。
文摘α/β(hcp/bcc)interfaces are of great importance in the microstructure development and the mechanical properties of titanium and zirconium alloys.This work contributes to the study of interface energetics and interfacial structures of the precipitate in the hcp/bcc system based on a simulation study using molecular statics(MS)and molecular dynamics(MD).The input orientation relationship(OR)was calculated based on the O-line criterion.Based on the energy of the interfaces containing the invariant line(IL),two preferred facets were determined by the Wulff construction,which explained the observed orientations of the habit plane(HP)and the side facet(SF).The deviation of the observed precipitate morphology from the equilibrium shape was discussed in terms of interface kinetics.The structures of the interfaces surrounding a three-dimensional(3 D)precipitate,including the preferred facets and the end face,were obtained at the atomic level.The simulated dislocation structures and atomic structures in these interfaces are in good agreement with those of the experimental observations for Ti-Cr alloys.A method was suggested for modifying the O-cell structure with the guidance of the relaxed structure,yielding consistency between the calculated dislocation structure based on the generalized O-element approach and the simulation results.
文摘Nd:YAG crystals free from core and dislocation have been grown by using the“controlled reversion of solid-liquid interface” method.The basic idea of the method is to combine the respective advantages of both the convex and the flat interface growth and to overpass "safely"the interface reversion so that the whole crystal could be grown in stable fluid How states.
文摘This paper attempts to explore the functional divergence of LD （Left Dislocation） in English and Chinese. Through detailed analyzing, we find that LD in both languages shares only one function, the function of simplifying, but it is different in other functions and there are eight more functions in Chinese than in English. The interface study of LD in the two languages leads to the implications： The connections between syntactic form and discourse function are language-specific and arbitrary, and LD serves a wide variety of discourse functions and is motivated by a range of discourse circumstances
基金supports from the National Natural Science Foundation of China(52175338 and 52222510)Science Fund for Distinguished Young Scholars of Shandong Province(ZR2021JQ21)Key Research and Development Program of Shandong Province(2021ZLGX01).
文摘Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.
基金supported by the National Key Research And Development Plan, China (No. 2016YFB1100100)the Research Fund of the State Key Laboratory of Solidification Processing (NWPU), China (No. KP201611)the National Natural Science Foundation of China (No. 51475380)
文摘Laser cladding deposited Ti-6Al-4V titanium alloy universally shows more complex microstructures,each of which has significant effect on mechanical properties. Of particular α/β interface phase has been observed in this paper under certain conditions. It demonstrates that the influence of the α/β interface phase on the tensile properties is closely associated with dislocations and twin substructure through comparison experiments. The results show that the α/β interface phase hinders dislocation motion and decreases effective slip length. In addition, the twin substructure has been activated in the α/β interface phase during tensile process and has acted somehow like grain boundaries. Therefore, the strength and the work-hardening rate of the laser cladding deposited Ti-6Al-4V titanium alloy have been significantly improved due to the dynamic Hall-Petch effect. Besides, the α/β interface phase leads to more uniform dislocations distribution, which implies that relative lower local concentrated stress will be produced along the α/β interface phase or colony boundary after the same amount of plastic deformation. Moreover,the twinning-induced plasticity effects in the α/β interface phase further increase the plastic deformation capacity. These results in higher elongation for the laser cladding deposited Ti-6Al-4V titanium alloy.It can be concluded that the current work suggests an effective method to simultaneously improve the strength and plasticity of laser cladding deposited Ti-6Al-4V titanium alloy based on the α/β interface phase.
