Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic...Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic source.Alternatively,laser interferometry with picometer-scale motional displacement detection can rapidly and precisely measure sound-induced minute vibrations on remote surfaces.Here,we demonstrate the feasibility of sound detection up to 100 kHz at remote sites with≈60 m optical path length via laser homodyne interferometry.Based on our ultrastable hertz linewidth laser with 10-15 fractional stability,our laser interferometer achieves 0.5 pm/Hz1/2 displacement sensitivity near 10 kHz,bounded only by laser frequency noise over 10 kHz.Between 140 Hz and 15 kHz,we achieve a homodyne acoustic sensing sensitivity of subnanometer/Pascal across our conversational frequency overtones.The minimal sound pressure detectable over 60 m optical path length is≈2 mPa,with dynamic ranges over 100 dB.With the demonstrated standoff picometric distance metrology,we successfully detected and reconstructed musical scores of normal conversational volumes with high fidelity.The acoustic detection via this precision laser interferometer could be applied to selective area sound sensing for remote acoustic metrology,optomechanical vibrational motion sensing,and ultrasensitive optical microphones at the laser frequency noise limits.展开更多
The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to inves...The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to investigate the gas dynamics of the bridge film after SCB plasma extinction.Interferometric images of the SCB film gas were obtained through a laser interferometry optical path.After the degradation model of digital image processing,clearer images were produced to facilitate analysis and calculation.The results show that the gas temperature at the center of the SCB film reaches a maximum of 1000 K,and the temperature rapidly decreases along the axial direction of the bridge surface to room temperature at 300 K.The maximum diffusion velocity of the plasma is 1.8 km/s.These findings provide critical insights for SCB design and ignition control.展开更多
Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive s...Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive spectral interferometry(DSI)shows promise for high-speed precision measurements,whereas the resolution of subnanometers has not yet been achieved.We present a comprehensive theoretical framework to analyze the limitations of real-time DSI based on the signal-to-noise ratio and data volume.A real-time orthogonal polarization spectral interferometry technique is proposed,which utilizes a pair of interferograms with the pi-phase shift to effectively mitigate the phase noise embedded in real-time spectral envelopes,thereby enabling the precise measurements with subnanometer resolution at megahertz frame rates.The recorded time series data are processed through interpolation,segmentation,time–frequency mapping,and de-enveloping to regain the typical cosine-shaped spectral evolution,followed by a fitting-based phase retrieval method to extract the interference phase.The phase resolution of 1.1 mrad(0.91 as for time delay and 0.3 nm for distance)is obtained at the update rate of 22.2 MHz even under the detection bandwidth of 500 MHz,and can be further enhanced to 0.29 mrad(0.24 as for time delay)after 500 times averaging(∼0.5 MHz).Our approach is validated through periodic phase modulations and applied to measure the rapid damped oscillations of a piezo stage,yielding results consistent with those obtained from a commercial picometer interferometer.展开更多
Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and a...Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and astronomy.Here,we design and fabricate silicon nitride,dispersion-managed microresonators that effectively suppress avoided-mode crossings and achieve close-to-zero averaged dispersion.Both the stochastic noise and mode-locking dynamics of the resonator are numerically and experimentally investigated.First,we experimentally demonstrate thermally stabilized microcomb formation in the microresonator across different mode-locked states,showing negligible center frequency shifts and a broad frequency bandwidth.Next,we characterize the femtosecond timing jitter of the microcombs,supported by precise metrology of the timing phase and relative intensity noise.For the single-soliton state,we report a relative intensity noise of−153.2 dB∕Hz,close to the shot-noise limit,and a quantum-noise–limited timing jitter power spectral density of 0.4 as 2∕Hz at a 100 kHz offset frequency,measured using a self-heterodyne linear interferometer.In addition,we achieve an integrated timing jitter of 1.7 fs±0.07 fs,measured from 10 kHz to 1 MHz.Measuring and understanding these fundamental noise parameters in high clock rate frequency microcombs is critical for advancing soliton physics and enabling new applications in precision metrology.展开更多
Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and pote...Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and potentially prevent the testing from proceeding normally.Position errors include the decenter error,tilt error,and distance error.During the testing process,position errors will impact the testing accuracy and the crosstalk fringes generated by stray light.To determine the specific impact of position errors,we use the concept of Hindle shell testing of a convex aspheric mirror,and propose the simulation method of crosstalk fringes in null compensation interferometry.We also propose evaluation indices of crosstalk fringes in interferometry and simulate the influence of position errors on the crosstalk fringes.This work aims to help improve the design of compensation interferometry schemes,enhance the feasibility of the design,reduce engineering risks,and improve efficiency.展开更多
Understanding rock behavior is crucial in mine geotechnical engineering to ensure construction efficiency,mitigate rock-related hazards,and promote environmental sustainability.Coda Wave Interferometry(CWI),a non-dest...Understanding rock behavior is crucial in mine geotechnical engineering to ensure construction efficiency,mitigate rock-related hazards,and promote environmental sustainability.Coda Wave Interferometry(CWI),a non-destructive ultrasonic testing method,has been widely employed to assess micro-damage evolution in rocks induced by perturbations in scatterer position,velocity,or source location due to its exceptional sensitivity.However,challenges persist in evaluating cross-scale rock behavior influenced by nonlinear deformation and multi-field interactions under multiple coupled perturbations.A comprehensive review of the perturbation factors affecting rock damage evolution and potential failure mechanisms is essential for presenting available knowledge in a more systematic and structured manner.This review provides an in-depth analysis of the CWI technique,encompassing its origins,theoretical framework,and classical data processing methodologies.Additionally,it explores the diverse applications of CWI in assessing rock behavior under various perturbation factors,including temperature variations,fluid infiltration,and stress conditions,with a particular emphasis on nonlinear deformation and multi-field coupling effects.Furthermore,a novel method for calculating relative velocity changes in coda waves is introduced,enabling a more precise characterization of the entire rock failure process.The study also proposes a cutting-edge concept of ultra-early and refined monitoring and warning technology for mine rock disasters,leveraging the advancements in CWI.Finally,the review highlights the potential future developments of CWI in high-level intelligent mining scenarios,particularly its integration with ambient noise interferometry and microseismic coda wave analysis.This work serves as a valuable reference,contributing to the refinement of CWI applications for assessing complex rock behavior and enhancing the accuracy of rock disaster prediction and early warning systems.展开更多
Laser frequency combs,which are composed of a series of equally spaced coherent frequency components,have triggered revolutionary progress in precision spectroscopy and optical metrology.Length/distance is of fundamen...Laser frequency combs,which are composed of a series of equally spaced coherent frequency components,have triggered revolutionary progress in precision spectroscopy and optical metrology.Length/distance is of fundamental importance in both science and technology.We describe a ranging scheme based on chirped pulse interferometry.In contrast to the traditional spectral interferometry,the local oscillator is strongly chirped which is able to meet the measurement pulses at arbitrary distances,and therefore,the dead zones can be removed.The distances can be precisely determined via two measurement steps based on the time-of-flight method and synthetic wavelength interferometry,respectively.To overcome the speed limitation of the optical spectrum analyzer,the spectrograms are stretched and detected by a fast photodetector and oscilloscope and consequently mapped into the time domain in real time.The experimental results indicate that the measurement uncertainty can be well within±2μm,compared with the reference distance meter.The Allan deviation can reach 0.4μm at 4 ns averaging time and 25 nm at 1μs and can achieve 2 nm at 100μs averaging time.We also measured a spinning disk with grooves of different depths to verify the measurement speed,and the results show that the grooves with about 150 m∕s line speed can be clearly captured.Our method provides a unique combination of non-dead zones,ultrafast measurement speed,high precision and accuracy,large ambiguity range,and only one single comb source.This system could offer a powerful solution for field measurements in practical applications in the future.展开更多
Single-wavelength interferometry achieves high resolution for smooth surfaces but struggles with rough industrially relevant ones due to limited unambiguous measuring range and speckle effects.Multiwavelength interfer...Single-wavelength interferometry achieves high resolution for smooth surfaces but struggles with rough industrially relevant ones due to limited unambiguous measuring range and speckle effects.Multiwavelength interferometry addresses these challenges using synthetic wavelengths,enabling a balance between extended measurement range and resolution by combining several synthetic wavelengths.This approach holds immense potential for diverse industrial applications,yet it remains largely untapped due to the lack of suitable light sources.Existing solutions are constrained by limited flexibility in synthetic-wavelength generation and slow switching speeds.We demonstrate a light source for multiwavelength interferometry based on electro-optic single-sideband modulation.It reliably generates synthetic wavelengths with arbitrary values from centimeters to meters and switching time below 30 ms.This breakthrough paves the way for dynamic reconfigurable multiwavelength interferometry capable of adapting to complex surfaces and operating efficiently even outside laboratory settings.These capabilities unlock the full potential of multiwavelength interferometry,offering unprecedented flexibility and speed for industrial and technological applications.展开更多
We propose a quantum-enhanced metrological scheme utilizing unbalanced entangled coherent states(ECSs) generated by passing a coherent state and a coherent state superposition through an unbalanced beam splitter(BS). ...We propose a quantum-enhanced metrological scheme utilizing unbalanced entangled coherent states(ECSs) generated by passing a coherent state and a coherent state superposition through an unbalanced beam splitter(BS). We identify the optimal phase sensitivity of this scheme by maximizing the quantum Fisher information(QFI) with respect to the BS transmission ratio. Our scheme outperforms the conventional scheme with a balanced BS, particularly in the presence of single-mode photon loss. Notably, our scheme retains quantum advantage in phase sensitivity in the limit of high photon intensity, where the balanced scheme offers no advantage over the classical strategy.展开更多
Atomic nonlinear interferometry has wide applications in quantum metrology and quantum information science.Here we propose a nonlinear time-reversal interferometry scheme with high robustness and metrological gain bas...Atomic nonlinear interferometry has wide applications in quantum metrology and quantum information science.Here we propose a nonlinear time-reversal interferometry scheme with high robustness and metrological gain based on the spin squeezing generated by arbitrary quadratic collective-spin interaction,which could be described by the Lipkin–Meshkov–Glick(LMG)model.We optimize the squeezing process,encoding process,and anti-squeezing process,finding that the two particular cases of the LMG model,one-axis twisting and two-axis twisting outperform in robustness and precision,respectively.Moreover,we propose a Floquet driving method to realize equivalent time reverse in the atomic system,which leads to high performance in precision,robustness,and operability.Our study sets a benchmark for achieving high precision and high robustness in atomic nonlinear interferometry.展开更多
The principle and application of optical interferometry to measure the coating thickness of color-coated plates were introduced in this paper.Additionally,several factors affecting the test results,including coating r...The principle and application of optical interferometry to measure the coating thickness of color-coated plates were introduced in this paper.Additionally,several factors affecting the test results,including coating refractive index,wavelength range,and film thickness range setting,were analyzed.Among these,the refractive index of the color coating,which cannot be measured directly,was identified as the key factor.A solution to this problem was proposed.Finally,the optical interference method and the current detection methods,including the micrometer method and the magnetic eddy current method,were analyzed and compared.The results show that optical interferometry has better repeatability and reproducibility than the current methods and show no significant difference from the current methods through statistical tests.Therefore,the method can be applied to the detection of the coating thickness of color-coated plates.展开更多
Dual-comb interferometric systems with high time accuracy have been realized for various applications.The flourishing ultralow noise dual-comb system promotes the measurement and characterization of relative timing ji...Dual-comb interferometric systems with high time accuracy have been realized for various applications.The flourishing ultralow noise dual-comb system promotes the measurement and characterization of relative timing jitter,thus improving time accuracy.With optical solutions,introducing an optical reference enables 105 harmonics measurements,thereby breaking the limit set by electrical methods;nonlinear processes or spectral interference schemes were also employed to track the relative timing jitter.However,such approaches operating in the time domain either require additional continuous references or impose stringent requirements on the amount of timing jitter.We propose a scheme to correct the relative timing jitter of a free-running dual-comb interferometry assisted by a Fabry-Pérot(F-P)cavity in the frequency domain.With high wavelength thermal stability provided by the F-P cavity,the absolute wavelength deviation in the operating bandwidth is compressed to<0.4 pm,corresponding to a subpicosecond sensitivity of pulse-to-pulse relative timing jitter.Also,Allan deviation of 10^(-10) is obtained under multiple coherent averaging,which lays the foundation for mode-resolved molecular spectroscopic applications.The spectral absorption features of hydrogen cyanide gas molecules at ambient temperature were measured and matched to the HITRAN database.Our scheme promises to provide new ideas on sensitive measurements of relative timing jitter.展开更多
In order to suppress the airwave noise in marine controlled-source electromagnetic （CSEM） data, we propose a 3D deconvolution （3DD） interferometry method with a synthetic aperture source and obtain the relative an...In order to suppress the airwave noise in marine controlled-source electromagnetic （CSEM） data, we propose a 3D deconvolution （3DD） interferometry method with a synthetic aperture source and obtain the relative anomaly coefficient （RAC） of the EM field reflection responses to show the degree for suppressing the airwave. We analyze the potential of the proposed method for suppressing the airwave, and compare the proposed method with traditional methods in their effectiveness. A method to select synthetic source length is derived and the effect of the water depth on RAC is examined via numerical simulations. The results suggest that 3DD interferometry method with a synthetic source can effectively suppress the airwave and enhance the potential of marine CSEM to hydrocarbon exploration.展开更多
Conventional synthetic aperture radar(SAR)interferometry(InSAR)has been successfully used to precisely measure surface deformation in the line-of-sight(LOS)direction,while multiple-aperture SAR interferometry(MAI)has ...Conventional synthetic aperture radar(SAR)interferometry(InSAR)has been successfully used to precisely measure surface deformation in the line-of-sight(LOS)direction,while multiple-aperture SAR interferometry(MAI)has provided precise surface deformation in the along-track(AT)direction.Integration of the InSAR and MAI methods enables precise measurement of the two-dimensional(2D)deformation from an interferometric pair;recently,the integration of ascending and descending pairs has allowed the observation of precise three-dimensional(3D)deformation.Precise 3D deformation measurement has been applied to better understand geological events such as earthquakes and volcanic eruptions.The surface deformation related to the 2016 Kumamoto earthquake was large and complex near the fault line;hence,precise 3D deformation retrieval had not yet been attempted.The objectives of this study were to①perform a feasibility test of precise 3D deformation retrieval in large and complex deformation areas through the integration of offset-based unwrapped and improved multiple-aperture SAR interferograms and②observe the 3D deformation field related to the 2016 Kumamoto earthquake,even near the fault lines.Two ascending pairs and one descending the Advanced Land Observing Satellite-2(ALOS-2)Phased Array-type L-band Synthetic Aperture Radar-2(PALSAR-2)pair were used for the 3D deformation retrieval.Eleven in situ Global Positioning System(GPS)measurements were used to validate the 3D deformation measurement accuracy.The achieved accuracy was approximately 2.96,3.75,and 2.86 cm in the east,north,and up directions,respectively.The results show the feasibility of precise 3D deformation measured through the integration of the improved methods,even in a case of large and complex deformation.展开更多
This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical...This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.展开更多
The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can obse...The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can observe the deformation of samples under pressure in the lab and study the anomaly characteristics relating to different strain fields in different fracture-developing areas; while by using RDI, we can observe the landform and surface deformation. The results of deformation observed before and after the Ms=7.9 Mani earthquake （Tibet） and Ms=6.2 Shangyi-Zhangbei earthquake in China are obtained. It is pointed out that LRTHI and RDi are similar, which study the characteristics of anomalous deformation field by fringe variations for both of them. Therefore, the observation of deformation field in the seismogenic process, especially in the period impending an earthquake by RDI, and the comparative study in the lab by LRTHI are of great significance.展开更多
Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorit...Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorithms, several different 3D electronic speckle pattern interferometry（ESPl） systems for displacement and strain measurements have been achieved and commercialized. This paper provides a review of the recent developments in ESPI systems for 3D displacement and strain measurement. After an overview of the fundamentals of ESP! theory, temporal phase-shift, and spatial phase-shift techniques, 3D deformation measurements by the temporal phase-shift ESPI system, which is suited well for static measurement, and by the spatial phase-shift ESPI system, which is particularly useful for dynamic measurement, are discussed. For each method, the basic theory, a brief derivation and different optical layouts are presented. The state of art application, potential and limitation of the ESPI systems are shown and demonstrated.展开更多
The experimental apparatus to measure the mass diffusion coefficients of O2 in aviation fuel was constructed based on the digital holographic interferometry method. The theory of mass diffusion coefficient and interfe...The experimental apparatus to measure the mass diffusion coefficients of O2 in aviation fuel was constructed based on the digital holographic interferometry method. The theory of mass diffusion coefficient and interference image processing were introduced in detail. The accuracy of the experiment was verified by measuring the mass diffusion coefficient of 0.33 mol/L KCl in aqueous solution at 298.15 K. The mass diffusion coefficients of O_2 in RP3 and RP5 aviation fuels were measured at temperature from 278.15 K to 333.15 K, and the Arrhenius equation was employed to fit the experimental data. In terms of the Stokes-Einstein equation, the viscosities of these two aviation fuels were tested to estimate the correlation among mass diffusion coefficient, viscosity and temperature. A uniform polynomial calculation correlation was proposed to predict the mass diffusion coefficients of O_2 in both RP3 and RP5 aviation fuels, and its accuracy is considerably higher than that of the Stokes-Einstein equation.展开更多
Real-time laser holographic interferometry was applied to measure liquid concentrations of CO2 in the vicinity of gas-liquid free interface under the conditions of cocurrent gas-liquid flow for absorption of CO2 by et...Real-time laser holographic interferometry was applied to measure liquid concentrations of CO2 in the vicinity of gas-liquid free interface under the conditions of cocurrent gas-liquid flow for absorption of CO2 by ethanol. The influences of the Reynolds number on the measurable interface concentration and on the film thickness were discussed. The results show that CO2 concentration decreases exponentially along the mass transfer direction,and the concentration gradient increases as Reynolds number of either liquid or gas increases. CO2 concentrations fluctuate slightly along the direction of flow; on the whole, there is an increase in CO2 concentration. The investigation also demonstrated that film thickness decreases with the increase of Reynolds number of either of the two phases. Sherwood number representing the mass transfer coefficient was finally correlated as a function of the hydrodynamic parameters and the physical properties.展开更多
Astrodynamical space test of relativity using optical devices optimized for gravitation wave detection （ASTROD- GW） is an optimization of ASTROD to focus on the goal of detection of gravitation waves. The detection ...Astrodynamical space test of relativity using optical devices optimized for gravitation wave detection （ASTROD- GW） is an optimization of ASTROD to focus on the goal of detection of gravitation waves. The detection sensitivity is shifted 52 times toward larger wavelength compared with that of laser interferometer space antenna （LISA）. The mission orbits of the three spacecrafts forming a nearly equilateral triangular array are chosen to be near the Sun–Earth Lagrange points L3, L4, and L5. The three spacecrafts range interferometrically with one another with an arm length of about 260 million kilometers. In order to attain the required sensitivity for ASTROD-GW, laser frequency noise must be suppressed to below the secondary noises such as the optical path noise, acceleration noise, etc. For suppressing laser frequency noise, we need to use time delay interferometry （TDI） to match the two different optical paths （times of travel）. Since planets and other solar-system bodies perturb the orbits of ASTROD-GW spacecraft and affect the TDI, we simulate the time delay numerically using CGC 2.7 （here, CGC stands for center for gravitation and cosmology） ephemeris framework. To conform to the ASTROD-GW planning, we work out a set of 20-year optimized mission orbits of ASTROD-GW spacecraft starting at June 21, 2028, and calculate the differences in optical path in the first and second generation TDIs separately for one-detector case. In our optimized mission orbits of 20 years, changes of arm lengths are less than 0.0003 AU; the relative Doppler velocities are all less than 3m/s. All the second generation TDI for one-detector case satisfies the ASTROD-GW requirement.展开更多
基金supported by the Office of Naval Research(Grant Nos.N00014-16-1-2094 and N00014-24-1-2547)the Lawrence Livermore National Laboratory(Grant No.B622827)the National Science Foundation.Y.-S.J.acknowledges support from KRISS(Grant Nos.25011026 and 25011211).
文摘Acoustic detection has many applications across science and technology from medicine to imaging and communications.However,most acoustic sensors have a common limitation in that the detection must be near the acoustic source.Alternatively,laser interferometry with picometer-scale motional displacement detection can rapidly and precisely measure sound-induced minute vibrations on remote surfaces.Here,we demonstrate the feasibility of sound detection up to 100 kHz at remote sites with≈60 m optical path length via laser homodyne interferometry.Based on our ultrastable hertz linewidth laser with 10-15 fractional stability,our laser interferometer achieves 0.5 pm/Hz1/2 displacement sensitivity near 10 kHz,bounded only by laser frequency noise over 10 kHz.Between 140 Hz and 15 kHz,we achieve a homodyne acoustic sensing sensitivity of subnanometer/Pascal across our conversational frequency overtones.The minimal sound pressure detectable over 60 m optical path length is≈2 mPa,with dynamic ranges over 100 dB.With the demonstrated standoff picometric distance metrology,we successfully detected and reconstructed musical scores of normal conversational volumes with high fidelity.The acoustic detection via this precision laser interferometer could be applied to selective area sound sensing for remote acoustic metrology,optomechanical vibrational motion sensing,and ultrasensitive optical microphones at the laser frequency noise limits.
基金supported by the Anhui Zhongchuang Energy New Energy Technology Co.,Ltd.,Entrusted Project.
文摘The semiconductor bridge(SCB)ignites through bridge film discharge,offering advantages such as low ignition energy,high safety,and compatibility with digital logic circuits.The study uses laser interferometry to investigate the gas dynamics of the bridge film after SCB plasma extinction.Interferometric images of the SCB film gas were obtained through a laser interferometry optical path.After the degradation model of digital image processing,clearer images were produced to facilitate analysis and calculation.The results show that the gas temperature at the center of the SCB film reaches a maximum of 1000 K,and the temperature rapidly decreases along the axial direction of the bridge surface to room temperature at 300 K.The maximum diffusion velocity of the plasma is 1.8 km/s.These findings provide critical insights for SCB design and ignition control.
基金supported by the National Natural Science Foundation of China(Grant No.61705193)the Natural Science Foundation of Zhejiang Province(Grant No.LGG20F050002)the Jinhua Science and Technology Plan(Project No.2024-1-064).
文摘Laser interferometry with higher resolution,faster update rate,and larger dynamic range is highly anticipated in the exploration of physics frontiers,advanced manufacturing,and precision sensing.Real-time dispersive spectral interferometry(DSI)shows promise for high-speed precision measurements,whereas the resolution of subnanometers has not yet been achieved.We present a comprehensive theoretical framework to analyze the limitations of real-time DSI based on the signal-to-noise ratio and data volume.A real-time orthogonal polarization spectral interferometry technique is proposed,which utilizes a pair of interferograms with the pi-phase shift to effectively mitigate the phase noise embedded in real-time spectral envelopes,thereby enabling the precise measurements with subnanometer resolution at megahertz frame rates.The recorded time series data are processed through interpolation,segmentation,time–frequency mapping,and de-enveloping to regain the typical cosine-shaped spectral evolution,followed by a fitting-based phase retrieval method to extract the interference phase.The phase resolution of 1.1 mrad(0.91 as for time delay and 0.3 nm for distance)is obtained at the update rate of 22.2 MHz even under the detection bandwidth of 500 MHz,and can be further enhanced to 0.29 mrad(0.24 as for time delay)after 500 times averaging(∼0.5 MHz).Our approach is validated through periodic phase modulations and applied to measure the rapid damped oscillations of a piezo stage,yielding results consistent with those obtained from a commercial picometer interferometer.
基金support from the Lawrence Livermore National Laboratory(Grant No.B622827)the National Science Foundation(Grant Nos.1824568,1810506,1741707,and 1829071)the Office of Naval Research(Grant No.N00014-16-1-2094).
文摘Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and astronomy.Here,we design and fabricate silicon nitride,dispersion-managed microresonators that effectively suppress avoided-mode crossings and achieve close-to-zero averaged dispersion.Both the stochastic noise and mode-locking dynamics of the resonator are numerically and experimentally investigated.First,we experimentally demonstrate thermally stabilized microcomb formation in the microresonator across different mode-locked states,showing negligible center frequency shifts and a broad frequency bandwidth.Next,we characterize the femtosecond timing jitter of the microcombs,supported by precise metrology of the timing phase and relative intensity noise.For the single-soliton state,we report a relative intensity noise of−153.2 dB∕Hz,close to the shot-noise limit,and a quantum-noise–limited timing jitter power spectral density of 0.4 as 2∕Hz at a 100 kHz offset frequency,measured using a self-heterodyne linear interferometer.In addition,we achieve an integrated timing jitter of 1.7 fs±0.07 fs,measured from 10 kHz to 1 MHz.Measuring and understanding these fundamental noise parameters in high clock rate frequency microcombs is critical for advancing soliton physics and enabling new applications in precision metrology.
基金the National Key Research and Development Program of China(2022YFB3403404)the Youth Innovation Promotion Association,CAS(2022213)the National Natural Science Foundation of China(62127901 and 62305334).
文摘Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and potentially prevent the testing from proceeding normally.Position errors include the decenter error,tilt error,and distance error.During the testing process,position errors will impact the testing accuracy and the crosstalk fringes generated by stray light.To determine the specific impact of position errors,we use the concept of Hindle shell testing of a convex aspheric mirror,and propose the simulation method of crosstalk fringes in null compensation interferometry.We also propose evaluation indices of crosstalk fringes in interferometry and simulate the influence of position errors on the crosstalk fringes.This work aims to help improve the design of compensation interferometry schemes,enhance the feasibility of the design,reduce engineering risks,and improve efficiency.
基金supported by the National Key Research and Development Program of China(Fund for Young Scientists 2021YFC2900400)Chongqing Outstanding Youth Science Fund project(CSTB2023NSCQ-JQX0027).
文摘Understanding rock behavior is crucial in mine geotechnical engineering to ensure construction efficiency,mitigate rock-related hazards,and promote environmental sustainability.Coda Wave Interferometry(CWI),a non-destructive ultrasonic testing method,has been widely employed to assess micro-damage evolution in rocks induced by perturbations in scatterer position,velocity,or source location due to its exceptional sensitivity.However,challenges persist in evaluating cross-scale rock behavior influenced by nonlinear deformation and multi-field interactions under multiple coupled perturbations.A comprehensive review of the perturbation factors affecting rock damage evolution and potential failure mechanisms is essential for presenting available knowledge in a more systematic and structured manner.This review provides an in-depth analysis of the CWI technique,encompassing its origins,theoretical framework,and classical data processing methodologies.Additionally,it explores the diverse applications of CWI in assessing rock behavior under various perturbation factors,including temperature variations,fluid infiltration,and stress conditions,with a particular emphasis on nonlinear deformation and multi-field coupling effects.Furthermore,a novel method for calculating relative velocity changes in coda waves is introduced,enabling a more precise characterization of the entire rock failure process.The study also proposes a cutting-edge concept of ultra-early and refined monitoring and warning technology for mine rock disasters,leveraging the advancements in CWI.Finally,the review highlights the potential future developments of CWI in high-level intelligent mining scenarios,particularly its integration with ambient noise interferometry and microseismic coda wave analysis.This work serves as a valuable reference,contributing to the refinement of CWI applications for assessing complex rock behavior and enhancing the accuracy of rock disaster prediction and early warning systems.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFC2204601)the National Natural Science Foundation of China(Grant Nos.11925503 and 12275093)+1 种基金the Natural Science Foundation of Hubei Province(Grant No.2021CFB019)the State Key Laboratory of Applied Optics(Grant No.SKLAO2022001A10).
文摘Laser frequency combs,which are composed of a series of equally spaced coherent frequency components,have triggered revolutionary progress in precision spectroscopy and optical metrology.Length/distance is of fundamental importance in both science and technology.We describe a ranging scheme based on chirped pulse interferometry.In contrast to the traditional spectral interferometry,the local oscillator is strongly chirped which is able to meet the measurement pulses at arbitrary distances,and therefore,the dead zones can be removed.The distances can be precisely determined via two measurement steps based on the time-of-flight method and synthetic wavelength interferometry,respectively.To overcome the speed limitation of the optical spectrum analyzer,the spectrograms are stretched and detected by a fast photodetector and oscilloscope and consequently mapped into the time domain in real time.The experimental results indicate that the measurement uncertainty can be well within±2μm,compared with the reference distance meter.The Allan deviation can reach 0.4μm at 4 ns averaging time and 25 nm at 1μs and can achieve 2 nm at 100μs averaging time.We also measured a spinning disk with grooves of different depths to verify the measurement speed,and the results show that the grooves with about 150 m∕s line speed can be clearly captured.Our method provides a unique combination of non-dead zones,ultrafast measurement speed,high precision and accuracy,large ambiguity range,and only one single comb source.This system could offer a powerful solution for field measurements in practical applications in the future.
基金supported by the German Federal Ministry of Education and Research,Research Program Quantum Systems(Grant No.13N16774).
文摘Single-wavelength interferometry achieves high resolution for smooth surfaces but struggles with rough industrially relevant ones due to limited unambiguous measuring range and speckle effects.Multiwavelength interferometry addresses these challenges using synthetic wavelengths,enabling a balance between extended measurement range and resolution by combining several synthetic wavelengths.This approach holds immense potential for diverse industrial applications,yet it remains largely untapped due to the lack of suitable light sources.Existing solutions are constrained by limited flexibility in synthetic-wavelength generation and slow switching speeds.We demonstrate a light source for multiwavelength interferometry based on electro-optic single-sideband modulation.It reliably generates synthetic wavelengths with arbitrary values from centimeters to meters and switching time below 30 ms.This breakthrough paves the way for dynamic reconfigurable multiwavelength interferometry capable of adapting to complex surfaces and operating efficiently even outside laboratory settings.These capabilities unlock the full potential of multiwavelength interferometry,offering unprecedented flexibility and speed for industrial and technological applications.
基金supported by the National Natural Science Foundation of China (Grant No. 12005106)support from the National Natural Science Foundation of China (Grant No. 11974189)+1 种基金support from the National Natural Science Foundation of China (Grant No. 12175106)the Postgraduate Research and Practice Innovation Program of Jiangsu Province (Grant No. JSCX23-0260)。
文摘We propose a quantum-enhanced metrological scheme utilizing unbalanced entangled coherent states(ECSs) generated by passing a coherent state and a coherent state superposition through an unbalanced beam splitter(BS). We identify the optimal phase sensitivity of this scheme by maximizing the quantum Fisher information(QFI) with respect to the BS transmission ratio. Our scheme outperforms the conventional scheme with a balanced BS, particularly in the presence of single-mode photon loss. Notably, our scheme retains quantum advantage in phase sensitivity in the limit of high photon intensity, where the balanced scheme offers no advantage over the classical strategy.
基金Project supported by the National Key R&D Program of China (Grant No.2023YFA1407600)the National Natural Science Foundation of China (Grant Nos.12275145,92050110,91736106,11674390,and 91836302)。
文摘Atomic nonlinear interferometry has wide applications in quantum metrology and quantum information science.Here we propose a nonlinear time-reversal interferometry scheme with high robustness and metrological gain based on the spin squeezing generated by arbitrary quadratic collective-spin interaction,which could be described by the Lipkin–Meshkov–Glick(LMG)model.We optimize the squeezing process,encoding process,and anti-squeezing process,finding that the two particular cases of the LMG model,one-axis twisting and two-axis twisting outperform in robustness and precision,respectively.Moreover,we propose a Floquet driving method to realize equivalent time reverse in the atomic system,which leads to high performance in precision,robustness,and operability.Our study sets a benchmark for achieving high precision and high robustness in atomic nonlinear interferometry.
文摘The principle and application of optical interferometry to measure the coating thickness of color-coated plates were introduced in this paper.Additionally,several factors affecting the test results,including coating refractive index,wavelength range,and film thickness range setting,were analyzed.Among these,the refractive index of the color coating,which cannot be measured directly,was identified as the key factor.A solution to this problem was proposed.Finally,the optical interference method and the current detection methods,including the micrometer method and the magnetic eddy current method,were analyzed and compared.The results show that optical interferometry has better repeatability and reproducibility than the current methods and show no significant difference from the current methods through statistical tests.Therefore,the method can be applied to the detection of the coating thickness of color-coated plates.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFF0705904)the National Natural Science Foundation of China(Grant Nos.61927817 and 62075072).
文摘Dual-comb interferometric systems with high time accuracy have been realized for various applications.The flourishing ultralow noise dual-comb system promotes the measurement and characterization of relative timing jitter,thus improving time accuracy.With optical solutions,introducing an optical reference enables 105 harmonics measurements,thereby breaking the limit set by electrical methods;nonlinear processes or spectral interference schemes were also employed to track the relative timing jitter.However,such approaches operating in the time domain either require additional continuous references or impose stringent requirements on the amount of timing jitter.We propose a scheme to correct the relative timing jitter of a free-running dual-comb interferometry assisted by a Fabry-Pérot(F-P)cavity in the frequency domain.With high wavelength thermal stability provided by the F-P cavity,the absolute wavelength deviation in the operating bandwidth is compressed to<0.4 pm,corresponding to a subpicosecond sensitivity of pulse-to-pulse relative timing jitter.Also,Allan deviation of 10^(-10) is obtained under multiple coherent averaging,which lays the foundation for mode-resolved molecular spectroscopic applications.The spectral absorption features of hydrogen cyanide gas molecules at ambient temperature were measured and matched to the HITRAN database.Our scheme promises to provide new ideas on sensitive measurements of relative timing jitter.
基金supported by the national project"Deep Exploration Technology and Experimentation"(SinoProbe-09-02)
文摘In order to suppress the airwave noise in marine controlled-source electromagnetic （CSEM） data, we propose a 3D deconvolution （3DD） interferometry method with a synthetic aperture source and obtain the relative anomaly coefficient （RAC） of the EM field reflection responses to show the degree for suppressing the airwave. We analyze the potential of the proposed method for suppressing the airwave, and compare the proposed method with traditional methods in their effectiveness. A method to select synthetic source length is derived and the effect of the water depth on RAC is examined via numerical simulations. The results suggest that 3DD interferometry method with a synthetic source can effectively suppress the airwave and enhance the potential of marine CSEM to hydrocarbon exploration.
基金This study was funded by the Korea Meteorological Administration Research and Development Program(KMI2017-9060)the National Research Foundation of Korea funded by the Korea government(NRF-2018M1A3A3A02066008)+1 种基金In addition,the ALOS-2 PALSAR-2 data used in this study are owned by the Japan Aerospace Exploration Agency(JAXA)and were provided through the JAXA’s ALOS-2 research program(RA4,PI No.1412)The GPS data were provided by the Geospatial Information Authority of Japan.
文摘Conventional synthetic aperture radar(SAR)interferometry(InSAR)has been successfully used to precisely measure surface deformation in the line-of-sight(LOS)direction,while multiple-aperture SAR interferometry(MAI)has provided precise surface deformation in the along-track(AT)direction.Integration of the InSAR and MAI methods enables precise measurement of the two-dimensional(2D)deformation from an interferometric pair;recently,the integration of ascending and descending pairs has allowed the observation of precise three-dimensional(3D)deformation.Precise 3D deformation measurement has been applied to better understand geological events such as earthquakes and volcanic eruptions.The surface deformation related to the 2016 Kumamoto earthquake was large and complex near the fault line;hence,precise 3D deformation retrieval had not yet been attempted.The objectives of this study were to①perform a feasibility test of precise 3D deformation retrieval in large and complex deformation areas through the integration of offset-based unwrapped and improved multiple-aperture SAR interferograms and②observe the 3D deformation field related to the 2016 Kumamoto earthquake,even near the fault lines.Two ascending pairs and one descending the Advanced Land Observing Satellite-2(ALOS-2)Phased Array-type L-band Synthetic Aperture Radar-2(PALSAR-2)pair were used for the 3D deformation retrieval.Eleven in situ Global Positioning System(GPS)measurements were used to validate the 3D deformation measurement accuracy.The achieved accuracy was approximately 2.96,3.75,and 2.86 cm in the east,north,and up directions,respectively.The results show the feasibility of precise 3D deformation measured through the integration of the improved methods,even in a case of large and complex deformation.
文摘This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.
基金Joint Seismological Science Foundation of China (201012).
文摘The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can observe the deformation of samples under pressure in the lab and study the anomaly characteristics relating to different strain fields in different fracture-developing areas; while by using RDI, we can observe the landform and surface deformation. The results of deformation observed before and after the Ms=7.9 Mani earthquake （Tibet） and Ms=6.2 Shangyi-Zhangbei earthquake in China are obtained. It is pointed out that LRTHI and RDi are similar, which study the characteristics of anomalous deformation field by fringe variations for both of them. Therefore, the observation of deformation field in the seismogenic process, especially in the period impending an earthquake by RDI, and the comparative study in the lab by LRTHI are of great significance.
基金supported by National Natural Science Foundation of China(Grant Nos.51275054,51075116)
文摘Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorithms, several different 3D electronic speckle pattern interferometry（ESPl） systems for displacement and strain measurements have been achieved and commercialized. This paper provides a review of the recent developments in ESPI systems for 3D displacement and strain measurement. After an overview of the fundamentals of ESP! theory, temporal phase-shift, and spatial phase-shift techniques, 3D deformation measurements by the temporal phase-shift ESPI system, which is suited well for static measurement, and by the spatial phase-shift ESPI system, which is particularly useful for dynamic measurement, are discussed. For each method, the basic theory, a brief derivation and different optical layouts are presented. The state of art application, potential and limitation of the ESPI systems are shown and demonstrated.
基金supported by the Aeronautical Science Foundation of China(No.20132852040)the Fundation of Graduate Innovation Center in NUAA(No.kfjj20170116)+1 种基金the Fundamental Research Funds for the Central Universitiesthe Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘The experimental apparatus to measure the mass diffusion coefficients of O2 in aviation fuel was constructed based on the digital holographic interferometry method. The theory of mass diffusion coefficient and interference image processing were introduced in detail. The accuracy of the experiment was verified by measuring the mass diffusion coefficient of 0.33 mol/L KCl in aqueous solution at 298.15 K. The mass diffusion coefficients of O_2 in RP3 and RP5 aviation fuels were measured at temperature from 278.15 K to 333.15 K, and the Arrhenius equation was employed to fit the experimental data. In terms of the Stokes-Einstein equation, the viscosities of these two aviation fuels were tested to estimate the correlation among mass diffusion coefficient, viscosity and temperature. A uniform polynomial calculation correlation was proposed to predict the mass diffusion coefficients of O_2 in both RP3 and RP5 aviation fuels, and its accuracy is considerably higher than that of the Stokes-Einstein equation.
基金Supported by the National Natural Science Foundation of China (No.20476072).
文摘Real-time laser holographic interferometry was applied to measure liquid concentrations of CO2 in the vicinity of gas-liquid free interface under the conditions of cocurrent gas-liquid flow for absorption of CO2 by ethanol. The influences of the Reynolds number on the measurable interface concentration and on the film thickness were discussed. The results show that CO2 concentration decreases exponentially along the mass transfer direction,and the concentration gradient increases as Reynolds number of either liquid or gas increases. CO2 concentrations fluctuate slightly along the direction of flow; on the whole, there is an increase in CO2 concentration. The investigation also demonstrated that film thickness decreases with the increase of Reynolds number of either of the two phases. Sherwood number representing the mass transfer coefficient was finally correlated as a function of the hydrodynamic parameters and the physical properties.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 10778710 and 10875171)
文摘Astrodynamical space test of relativity using optical devices optimized for gravitation wave detection （ASTROD- GW） is an optimization of ASTROD to focus on the goal of detection of gravitation waves. The detection sensitivity is shifted 52 times toward larger wavelength compared with that of laser interferometer space antenna （LISA）. The mission orbits of the three spacecrafts forming a nearly equilateral triangular array are chosen to be near the Sun–Earth Lagrange points L3, L4, and L5. The three spacecrafts range interferometrically with one another with an arm length of about 260 million kilometers. In order to attain the required sensitivity for ASTROD-GW, laser frequency noise must be suppressed to below the secondary noises such as the optical path noise, acceleration noise, etc. For suppressing laser frequency noise, we need to use time delay interferometry （TDI） to match the two different optical paths （times of travel）. Since planets and other solar-system bodies perturb the orbits of ASTROD-GW spacecraft and affect the TDI, we simulate the time delay numerically using CGC 2.7 （here, CGC stands for center for gravitation and cosmology） ephemeris framework. To conform to the ASTROD-GW planning, we work out a set of 20-year optimized mission orbits of ASTROD-GW spacecraft starting at June 21, 2028, and calculate the differences in optical path in the first and second generation TDIs separately for one-detector case. In our optimized mission orbits of 20 years, changes of arm lengths are less than 0.0003 AU; the relative Doppler velocities are all less than 3m/s. All the second generation TDI for one-detector case satisfies the ASTROD-GW requirement.
