Cyclic loads generated by environmental factors,such as winds,waves,and trains,will likely lead to performance degradation in pile foundations,resulting in issues like permanent displacement accumulation and bearing c...Cyclic loads generated by environmental factors,such as winds,waves,and trains,will likely lead to performance degradation in pile foundations,resulting in issues like permanent displacement accumulation and bearing capacity attenuation.This paper presents a semi-analytical solution for predicting the axial cyclic behavior of piles in sands.The solution relies on two enhanced nonlinear load-transfer models considering stress-strain hysteresis and cyclic degradation in the pile-soil interaction.Model parameters are calibrated through cyclic shear tests of the sand-steel interface and laboratory geotechnical testing of sands.A novel aspect involves the meticulous formulation of the shaft loadtransfer function using an interface constitutive model,which inherently inherits the interface model’s advantages,such as capturing hysteresis,hardening,degradation,and particle breakage.The semi-analytical solution is computed numerically using the matrix displacement method,and the calculated values are validated through model tests performed on non-displacement and displacement piles in sands.The results demonstrate that the predicted values show excellent agreement with the measured values for both the static and cyclic responses of piles in sands.The displacement pile response,including factors such as bearing capacity,mobilized shaft resistance,and convergence rate of permanent settlement,exhibit improvements compared to non-displacement piles attributed to the soil squeezing effect.This methodology presents an innovative analytical framework,allowing for integrating cyclic interface models into the theoretical investigation of pile responses.展开更多
The total internal reflection(TIR)behavior of interface shear waves is crucial for ensuring the reliability of dielectric elastomer(DE)devices.However,due to the complex force-electric coupling and large deformation o...The total internal reflection(TIR)behavior of interface shear waves is crucial for ensuring the reliability of dielectric elastomer(DE)devices.However,due to the complex force-electric coupling and large deformation of DEs,the TIR behavior of shear waves in heterogeneous force-electric interface models is still unclear.This study modeled an elastic/DE bi-material interface to analyze the trajectory of out-of-plane shear waves.Employing Dorfmann and Ogden’s nonlinear electroelastic framework and the related linear small incremental motion theory,a method has been developed to control the TIR behavior of interface shear waves.It has been found that the TIR behavior is significantly influenced by the strain-stiffening effect induced by biasing fields.Consequently,a biasing field principle involving preset electric displacement and pre-stretch has been proposed for TIR occurrence.By controlling the pre-stretch and preset electric displacement,active regulation of TIR behavior can be achieved.These results suggest a potential method for achieving autonomous energy shielding to improve the reliability of DE devices.展开更多
Building a model for a object through model composition is a interesting topics, this paper research the interface composit ion of models in the Zeigler’s modeling methodology DEVS.
The Cr-plated coating inside a gun barrel can effectively improve the barrel’s erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gunpowder,micro-e...The Cr-plated coating inside a gun barrel can effectively improve the barrel’s erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gunpowder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel’s inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface’s ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.展开更多
Metallic flaky sendust particles are prepared for use as fillers in electromagnetic attenuation composites. We report the interface reflection model to divide the broad bandwidth into electromagnetic loss and quarter-...Metallic flaky sendust particles are prepared for use as fillers in electromagnetic attenuation composites. We report the interface reflection model to divide the broad bandwidth into electromagnetic loss and quarter-wavelength （λ/4） cancelation. Combining with the face reflection calculation, we identify the electromagnetic loss originated from skin effect, which is used to explain over half of the absorbed energy in high frequency band. Most impor- tantly, the unique electromagnetic loss cannot generate the reflection loss （RL） peak. Using the phase relation of face reflection, we show evidence that the λ/4 cancelation is vital to generate the RL peak. The calculated energy loss agrees well with the experimental data and lays the foundation for further research.展开更多
This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By me...This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By means of a comprehensive framework,a Coulomb-type failure criterion accounting for friction mobilization was defined.During the elastic phase,in which the interface joint is not yet created,the proposed model provides zero radial displacement,and once the interface joint is created,interface dilatancy is modeled using a non-associated plastic potential inspired from the behavior of rock joints.The results predicted by the proposed model are in good agreement with experimental results.The model has been implemented in a finite element method(FEM)code and numerical simulations have been performed at the elementary and the structural scales.The results obtained provide confidence in the ability of the new model to assist in the design and optimization of bolting patterns.展开更多
The microstructures of the Zn-27Al alloy after modification, solid-solution treatment, and natural aging were studied. It was clarified why the damping properties of Zn-27Al alloys, after treatment, had advanced most ...The microstructures of the Zn-27Al alloy after modification, solid-solution treatment, and natural aging were studied. It was clarified why the damping properties of Zn-27Al alloys, after treatment, had advanced most on the basis of analyzing the microstructures. Approximate expressions have been educed, which can be used to quantificationally work out the damping of the Zn-27Al alloy on the basis of the micro interface sliding model. By comparing the testing damping properties of the foundry Zn-27Al alloys and the Zn-27Al alloys after modification, solid solution, and natural aging, it was shown that the expressions were rational.展开更多
The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibriu...The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibrium state,equilibrium concentration distribution,MSD of layer and different groups,and interaction energy of two interface models,the influencing mechanism on the interface properties of adding organosiloxane into coating system was studied at the atomic scale.It shows that the temperature and energy of interface oscillated in a small range and it was exited in a state of dynamic equilibrium within the initial simulation stage(t<20 ps).It can be seen from the multiple peak states of concentration distribution that the iron substrate,organo-siloxane and zinc silicate are distributed in the form of a concentration gradient in the real environment.The rapid diffusion of free zinc powder in zinc silicate coating was the essential reason that affected the comprehensive properties of coating.The interface thickness decreased from 7.45 to 6.82Å,the MSD of free zinc powder was effectively reduced,and the interfacial energy was increased from 104.667 to 347.158 kcal/mol after being modified by organo-siloxane.展开更多
Seismic traveltime tomographic inversion has played an important role in detecting the internal structure of the solid earth. We use a set of blocks to approximate geologically complex media that cannot be well descri...Seismic traveltime tomographic inversion has played an important role in detecting the internal structure of the solid earth. We use a set of blocks to approximate geologically complex media that cannot be well described by layered models or cells. The geological body is described as an aggregate of arbitrarily shaped blocks,which are separated by triangulated interfaces. We can describe the media as homogenous or heterogeneous in each block. We define the velocities at the given rectangle grid points for each block,and the heterogeneous velocities in each block can be calculated by a linear interpolation algorithm. The parameters of the velocity grid positions are independent of the model parameterization,which is advantageous in the joint inversion of the velocities and the node depths of an interface. We implement a segmentally iterative ray tracer to calculate traveltimes in the 3D heterogeneous block models.The damped least squares method is employed in seismic traveltime inversion,which includes the partial derivatives of traveltime with respect to the depths of nodes in the triangulated interfaces and velocities defined in rectangular grids. The numerical tests indicate that the node depths of a triangulated interface and homogeneous velocity distributions can be well inverted in a stratified model.展开更多
A unified constitutive modeling approach is highly desirable to characterize a wide range of engineeringmaterials subjected simultaneously to the effect of a number of factors such as elastic, plastic and creepdeforma...A unified constitutive modeling approach is highly desirable to characterize a wide range of engineeringmaterials subjected simultaneously to the effect of a number of factors such as elastic, plastic and creepdeformations, stress path, volume change, microcracking leading to fracture, failure and softening,stiffening, and mechanical and environmental forces. There are hardly available such unified models. Thedisturbed state concept （DSC） is considered to be a unified approach and is able to provide materialcharacterization for almost all of the above factors. This paper presents a description of the DSC, andstatements for determination of parameters based on triaxial, multiaxial and interface tests. Statementsof DSC and validation at the specimen level and at the boundary value problem levels are also presented.An extensive list of publications by the author and others is provided at the end. The DSC is considered tobe a unique and versatile procedure for modeling behaviors of engineering materials and interfaces. 2016 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. This is an open access article under the CC BY-NC-ND license展开更多
The quantitative phase-field simulations were reviewed on the processes of solidification of pure metals and alloys.The quantitative phase-field equations were treated in a diffuse thin-interface limit,which enabled t...The quantitative phase-field simulations were reviewed on the processes of solidification of pure metals and alloys.The quantitative phase-field equations were treated in a diffuse thin-interface limit,which enabled the quantitative links between interface dynamics and model parameters in the quasi-equilibrium simulations.As a result,the quantitative modeling is more effective in dealing with microstructural pattern formation in the large scale simulations without any spurious kinetic effects.The development of the quantitative phase-field models in modeling the formation of microstructures such as dendritic structures,eutectic lamellas,seaweed morphologies,and grain boundaries in different solidified conditions was also reviewed with the purpose of guiding to find the new prospect of applications in the quantitative phase-field simulations.展开更多
Anti-icing is crucial for numerous instruments and devices in low temperature circum- stance. One of the approaches in anti-icing is to reduce ice adhesion strength, seeking spontaneous de-icing processes by natural f...Anti-icing is crucial for numerous instruments and devices in low temperature circum- stance. One of the approaches in anti-icing is to reduce ice adhesion strength, seeking spontaneous de-icing processes by natural forces of gravity or by winds. In order to enable tai- lored surface icephobicity design, research requires a good theoretical understanding of the atomistic interacting mechanisms between water/ice molecules and their adhering substrates. Herein, this work focuses on using atomistic modeling and molecular dynamics simulation to build a nanosized ice-cube adhering onto silicon surface, with different contact modes of solid-solid and solid-liquid-solid patterns. This study provides atomistic models for probing nanoscale ice adhesion mechanics and theoretical platforms for explaining experimental results.展开更多
There have already been several interface models for the analyses of thin interfacial layers in bonded materials. To distinguish their corresponding advantages or limitations, a comparative study is carried out, and a...There have already been several interface models for the analyses of thin interfacial layers in bonded materials. To distinguish their corresponding advantages or limitations, a comparative study is carried out, and a new constitutive-based interface model is proposed. Through numerical examinations, the limitations of typical models are clarified. It is found that the new interface model is an efficient and accurate model, by which both the traction and the displacement jumps across the modelled interface with the thickness of zero are allowed, and the stresses within the interracial layer can also be analyzed.展开更多
Being a wide variety of thin-layered interconnection components in electronics packaging with relatively small scale and heterogeneous materials, conventional numerical methods may be time consuming and even inefficac...Being a wide variety of thin-layered interconnection components in electronics packaging with relatively small scale and heterogeneous materials, conventional numerical methods may be time consuming and even inefficacious to obtain an accurate prediction for the interface behavior under mechanical and/or thermal loading. Rather than resort to a fully spatial discretization in the vicinity of this interface zone, an interface model was proposed within the framework of micropolar theory by introducing discontinuous approximation. A fracture description was used to represent the microscopic failure progress inside the interface. The micropolar interface model was then numerically implemented with the finite element method. As an application, the interface behavior of a packaging system with anisotropic conductive adhesive (ACA) joint was analyzed, demonstrating its applicability and great efficiency.展开更多
By applying the segmentation and composition principles of ecosystem,the structure and interface of earth ecosystem are fully elaborated,and corresponding model diagrams are established to display its composition and ...By applying the segmentation and composition principles of ecosystem,the structure and interface of earth ecosystem are fully elaborated,and corresponding model diagrams are established to display its composition and interconversion. The research finds that earth ecosystem includes three sub-ecosystems： terrestrial ecosystem,marine ecosystem and atmospheric ecosystem. The impact sequence of sub-ecosystems on earth ecosystem is atmospheric ecosystem 〉 marine ecosystem 〉 terrestrial ecosystem. Based on the segmentation and composition principles of ecosystem and the application of earth ecosystem structure and interface,we give new explanations to Taoism and Taiji with the eight diagrams,which contributes to theoretical research of natural science.展开更多
The influences of interphase on dynamic effective properties of composites reinforced by randomly dispersed spherical particles were studied. A thin homogeneous elastic interphase with different shear and bulk moduli,...The influences of interphase on dynamic effective properties of composites reinforced by randomly dispersed spherical particles were studied. A thin homogeneous elastic interphase with different shear and bulk moduli, located between the reinforced particle and the host matrix, was introduced to model the interfacial bonding state. The effects of such an interphase on the coherent plane waves were studied numerically. Numerical simulations were carried out for SiC-Al composites with four typical cases of interphase. It was found that the property of interphase has significant influences on the effective propagation constants of coherent waves and the dynamic effective elastic moduli of the composites. The influences on the coherent longitudinal wave and the coherent shear waves were different and dependent upon the frequency range. Moreover, several imperfect interface models, i.e., the spring model, mass model, and spring-mass model, were studied numerically and compared with the interphase model, It was found that the spring model is a more suitable model than the mass model for the light and weak interphase whereas the mass model is a more suitable model than the spring model for the heavy and strong interphase.展开更多
The development of a powerful numerical model to simulate the fracture behavior of concrete material has long been one of the dominant research areas in earthquake engineering. A reliable model should be able to adequ...The development of a powerful numerical model to simulate the fracture behavior of concrete material has long been one of the dominant research areas in earthquake engineering. A reliable model should be able to adequately represent the discontinuous characteristics of cracks and simulate various failure behaviors under complicated loading conditions. In this paper, a numerical formulation, which incorporates a sophisticated rigid-plastic interface constitutive model coupling cohesion softening, contact, friction and shear dilatation into the XFEM, is proposed to describe various crack behaviors of concrete material. An effective numerical integration scheme for accurately assembling the contribution to the weak form on both sides of the discontinuity is introduced. The effectiveness of the proposed method has been assessed by simulating several well-known experimental tests. It is concluded that the numerical method can successfully capture the crack paths and accurately predict the fracture behavior of concrete structures. The influence ofmode-Ⅱ parameters on the mixed-mode fracture behavior is further investigated to better determine these parameters.展开更多
Aiming at the characteristics of modularity and reconfigurable in open architecture computer numerical control （CNC） system, the open architecture CNC system, Harbin Institute of Tech- nology computer numerical cont...Aiming at the characteristics of modularity and reconfigurable in open architecture computer numerical control （CNC） system, the open architecture CNC system, Harbin Institute of Tech- nology computer numerical control （HITCNC）, is researched and manufactured based on the interface standards. The system＇s external interfaces are coincident with the corresponding international standards, and the internal interfaces follow the open modular architecture controller （OMAC） agreement. In the research and manufacturing process, object-oriented technology is used to ensure the openness of the HITCNC, and static programming is applied in the CNC system according to the idea of modularization disassembly. The HITCNC also actualizes real-time and unreal-time modules adopting real-time dynamical linked library （RTDLL） and component object model （COM）. Finite state ma- chine （FSM） is adopted to do dynamically modeling of HITCNC. The complete separation between the software and the hardware is achieved in the HITCNC by applying the SoftSERCANS technique. The application of the above key techniques decreases the programming workload greatly, and uses software programs replacing hardware functions, which offers plenty technique ensures for the openness of HITCNC. Finally, based on the HITCNC, a three-dimensional milling system is established. On the system, series experiments are done to validate the expandability and interchangeability of HITCNC. The results of the experiments show that the established open architecture CNC system HITCNC is correct and feasible, and has good openness.展开更多
This paper reviews differences between the deterministic(sharp and diffuse)and statistical models of the interphase region between the two-phases.In the literature this region is usually referred to as the(macroscopic...This paper reviews differences between the deterministic(sharp and diffuse)and statistical models of the interphase region between the two-phases.In the literature this region is usually referred to as the(macroscopic)interface.Therein,the mesoscopic interface that is defined at the molecular level and agitated by the thermal fluctuations is found with nonzero probability.For this reason,in this work,the interphase region is called the mesoscopic intermittency/transition region.To this purpose,the first part of the present work gives the rationale for introduction of the mesoscopic intermittency region statistical model.It is argued that classical(deterministic)sharp and diffuse models do not explain the experimental and numerical results presented in the literature.Afterwards,it is elucidated that a statistical model of the mesoscopic intermittency region(SMIR)combines existing sharp and diffuse models into a single coherent framework and explains published experimental and numerical results.In the second part of the present paper,the SMIR is used for the first time to predict equilibrium and nonequilibrium two-phase flow in the numerical simulation.To this goal,a two-dimensional rising gas bubble is studied;obtained numerical results are used as a basis to discuss differences between the deterministic and statistical models showing the statistical description has a potential to account for the physical phenomena not previously considered in the computer simulations.展开更多
Submerged arc welding process has been simulated to investigate the molten pool features of EH36 shipbuilding steel.One case only involved the surface tension model,and another one involved both the surface tension mo...Submerged arc welding process has been simulated to investigate the molten pool features of EH36 shipbuilding steel.One case only involved the surface tension model,and another one involved both the surface tension model and the interface tension model.The role of interface tension during welding is revealed,and the evolution of molten pool morphology is understood by comparing the surface temperature distribution,surface tension and interface tension distribution,and the streamline of the molten pool for the two cases.When the interface tension model is disregarded,a flow conducive to the outward expansion is formed in the surface area of the molten pool,resulting in a small weld depth-to-width ratio.After applying the interface tension model,the expanding outward flow is restrained,which leads to a deep penetration morphology with a large weld depth-to-width ratio due to the inward flow governed by the Marangoni forces.The simulation results involving the interface tension model have been verified with satisfactory predictability.展开更多
基金the financial support provided by the National Natural Science Foundation of China(Grant No.42272310).
文摘Cyclic loads generated by environmental factors,such as winds,waves,and trains,will likely lead to performance degradation in pile foundations,resulting in issues like permanent displacement accumulation and bearing capacity attenuation.This paper presents a semi-analytical solution for predicting the axial cyclic behavior of piles in sands.The solution relies on two enhanced nonlinear load-transfer models considering stress-strain hysteresis and cyclic degradation in the pile-soil interaction.Model parameters are calibrated through cyclic shear tests of the sand-steel interface and laboratory geotechnical testing of sands.A novel aspect involves the meticulous formulation of the shaft loadtransfer function using an interface constitutive model,which inherently inherits the interface model’s advantages,such as capturing hysteresis,hardening,degradation,and particle breakage.The semi-analytical solution is computed numerically using the matrix displacement method,and the calculated values are validated through model tests performed on non-displacement and displacement piles in sands.The results demonstrate that the predicted values show excellent agreement with the measured values for both the static and cyclic responses of piles in sands.The displacement pile response,including factors such as bearing capacity,mobilized shaft resistance,and convergence rate of permanent settlement,exhibit improvements compared to non-displacement piles attributed to the soil squeezing effect.This methodology presents an innovative analytical framework,allowing for integrating cyclic interface models into the theoretical investigation of pile responses.
基金supported by the National Natural Science Foundation of China(Grant No.12372154)National Science and Technology Major Project(Grant No.J2019-III-0010-0054).
文摘The total internal reflection(TIR)behavior of interface shear waves is crucial for ensuring the reliability of dielectric elastomer(DE)devices.However,due to the complex force-electric coupling and large deformation of DEs,the TIR behavior of shear waves in heterogeneous force-electric interface models is still unclear.This study modeled an elastic/DE bi-material interface to analyze the trajectory of out-of-plane shear waves.Employing Dorfmann and Ogden’s nonlinear electroelastic framework and the related linear small incremental motion theory,a method has been developed to control the TIR behavior of interface shear waves.It has been found that the TIR behavior is significantly influenced by the strain-stiffening effect induced by biasing fields.Consequently,a biasing field principle involving preset electric displacement and pre-stretch has been proposed for TIR occurrence.By controlling the pre-stretch and preset electric displacement,active regulation of TIR behavior can be achieved.These results suggest a potential method for achieving autonomous energy shielding to improve the reliability of DE devices.
文摘Building a model for a object through model composition is a interesting topics, this paper research the interface composit ion of models in the Zeigler’s modeling methodology DEVS.
文摘The Cr-plated coating inside a gun barrel can effectively improve the barrel’s erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gunpowder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel’s inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface’s ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.
基金Supported by the Fundamental Research Fund for the Central Universities under Grant No LZUJBKY-2015-121the National Natural Science Foundations of China under Grant Nos 11574122 and 51102124the National Science Foundation for Fostering Talents in Basic Research of the National Natural Science Foundation of China
文摘Metallic flaky sendust particles are prepared for use as fillers in electromagnetic attenuation composites. We report the interface reflection model to divide the broad bandwidth into electromagnetic loss and quarter-wavelength （λ/4） cancelation. Combining with the face reflection calculation, we identify the electromagnetic loss originated from skin effect, which is used to explain over half of the absorbed energy in high frequency band. Most impor- tantly, the unique electromagnetic loss cannot generate the reflection loss （RL） peak. Using the phase relation of face reflection, we show evidence that the λ/4 cancelation is vital to generate the RL peak. The calculated energy loss agrees well with the experimental data and lays the foundation for further research.
基金supported by the Research Fund for Coal and Steel(RFCS)in the context of the European project Advancing Mining Support Systems to Enhance the Control of Highly Stressed Ground(AMSSTED)。
文摘This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By means of a comprehensive framework,a Coulomb-type failure criterion accounting for friction mobilization was defined.During the elastic phase,in which the interface joint is not yet created,the proposed model provides zero radial displacement,and once the interface joint is created,interface dilatancy is modeled using a non-associated plastic potential inspired from the behavior of rock joints.The results predicted by the proposed model are in good agreement with experimental results.The model has been implemented in a finite element method(FEM)code and numerical simulations have been performed at the elementary and the structural scales.The results obtained provide confidence in the ability of the new model to assist in the design and optimization of bolting patterns.
文摘The microstructures of the Zn-27Al alloy after modification, solid-solution treatment, and natural aging were studied. It was clarified why the damping properties of Zn-27Al alloys, after treatment, had advanced most on the basis of analyzing the microstructures. Approximate expressions have been educed, which can be used to quantificationally work out the damping of the Zn-27Al alloy on the basis of the micro interface sliding model. By comparing the testing damping properties of the foundry Zn-27Al alloys and the Zn-27Al alloys after modification, solid solution, and natural aging, it was shown that the expressions were rational.
基金supported by the National Science Fundation of China(No.U1937601),and the National Natural Science Foundation of China(Grant No.NSFC51905471).
文摘The interface properties of Fe(101)/zinc silicate modified by organo-siloxane(KH-570)was studied by using the method of molecular dynamics simulation.By calculating the temperature and energy fluctuation of equilibrium state,equilibrium concentration distribution,MSD of layer and different groups,and interaction energy of two interface models,the influencing mechanism on the interface properties of adding organosiloxane into coating system was studied at the atomic scale.It shows that the temperature and energy of interface oscillated in a small range and it was exited in a state of dynamic equilibrium within the initial simulation stage(t<20 ps).It can be seen from the multiple peak states of concentration distribution that the iron substrate,organo-siloxane and zinc silicate are distributed in the form of a concentration gradient in the real environment.The rapid diffusion of free zinc powder in zinc silicate coating was the essential reason that affected the comprehensive properties of coating.The interface thickness decreased from 7.45 to 6.82Å,the MSD of free zinc powder was effectively reduced,and the interfacial energy was increased from 104.667 to 347.158 kcal/mol after being modified by organo-siloxane.
基金supported financially by the Ministry of Science and Technology of China(2011CB808904)the National Natural Science Foundation of China(Nos.41021063,41174075,41004034,41174043,and 41274090)
文摘Seismic traveltime tomographic inversion has played an important role in detecting the internal structure of the solid earth. We use a set of blocks to approximate geologically complex media that cannot be well described by layered models or cells. The geological body is described as an aggregate of arbitrarily shaped blocks,which are separated by triangulated interfaces. We can describe the media as homogenous or heterogeneous in each block. We define the velocities at the given rectangle grid points for each block,and the heterogeneous velocities in each block can be calculated by a linear interpolation algorithm. The parameters of the velocity grid positions are independent of the model parameterization,which is advantageous in the joint inversion of the velocities and the node depths of an interface. We implement a segmentally iterative ray tracer to calculate traveltimes in the 3D heterogeneous block models.The damped least squares method is employed in seismic traveltime inversion,which includes the partial derivatives of traveltime with respect to the depths of nodes in the triangulated interfaces and velocities defined in rectangular grids. The numerical tests indicate that the node depths of a triangulated interface and homogeneous velocity distributions can be well inverted in a stratified model.
文摘A unified constitutive modeling approach is highly desirable to characterize a wide range of engineeringmaterials subjected simultaneously to the effect of a number of factors such as elastic, plastic and creepdeformations, stress path, volume change, microcracking leading to fracture, failure and softening,stiffening, and mechanical and environmental forces. There are hardly available such unified models. Thedisturbed state concept （DSC） is considered to be a unified approach and is able to provide materialcharacterization for almost all of the above factors. This paper presents a description of the DSC, andstatements for determination of parameters based on triaxial, multiaxial and interface tests. Statementsof DSC and validation at the specimen level and at the boundary value problem levels are also presented.An extensive list of publications by the author and others is provided at the end. The DSC is considered tobe a unique and versatile procedure for modeling behaviors of engineering materials and interfaces. 2016 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. This is an open access article under the CC BY-NC-ND license
基金supported by National Natural Science Foundation of China(No.51174177)the Fund of the State Key Solidification Laboratory of Solidification Processing in Northwestern Polytechnical University(No.SKLSP 201714)
文摘The quantitative phase-field simulations were reviewed on the processes of solidification of pure metals and alloys.The quantitative phase-field equations were treated in a diffuse thin-interface limit,which enabled the quantitative links between interface dynamics and model parameters in the quasi-equilibrium simulations.As a result,the quantitative modeling is more effective in dealing with microstructural pattern formation in the large scale simulations without any spurious kinetic effects.The development of the quantitative phase-field models in modeling the formation of microstructures such as dendritic structures,eutectic lamellas,seaweed morphologies,and grain boundaries in different solidified conditions was also reviewed with the purpose of guiding to find the new prospect of applications in the quantitative phase-field simulations.
基金the financial support from Statoil ASA (Norway) through the project of nanotechnology for anti-icing application, NTNU stjerneprogramthe Research Council of Norway through the FRINATEK project Towards Design of Super-Low Ice Adhesion Surfaces ( SLICE,250990 )
文摘Anti-icing is crucial for numerous instruments and devices in low temperature circum- stance. One of the approaches in anti-icing is to reduce ice adhesion strength, seeking spontaneous de-icing processes by natural forces of gravity or by winds. In order to enable tai- lored surface icephobicity design, research requires a good theoretical understanding of the atomistic interacting mechanisms between water/ice molecules and their adhering substrates. Herein, this work focuses on using atomistic modeling and molecular dynamics simulation to build a nanosized ice-cube adhering onto silicon surface, with different contact modes of solid-solid and solid-liquid-solid patterns. This study provides atomistic models for probing nanoscale ice adhesion mechanics and theoretical platforms for explaining experimental results.
基金supported by the National Natural Science Foundation of China(No.10632040)
文摘There have already been several interface models for the analyses of thin interfacial layers in bonded materials. To distinguish their corresponding advantages or limitations, a comparative study is carried out, and a new constitutive-based interface model is proposed. Through numerical examinations, the limitations of typical models are clarified. It is found that the new interface model is an efficient and accurate model, by which both the traction and the displacement jumps across the modelled interface with the thickness of zero are allowed, and the stresses within the interracial layer can also be analyzed.
基金supported by the National Natural Science Foundation of China (Grant No.10702037)the Shanghai Pujiang Program(Grant No.08PJ14054)the Innovation Program of Shanghai Municipal Education Commission (Grant No.09YZ01)
文摘Being a wide variety of thin-layered interconnection components in electronics packaging with relatively small scale and heterogeneous materials, conventional numerical methods may be time consuming and even inefficacious to obtain an accurate prediction for the interface behavior under mechanical and/or thermal loading. Rather than resort to a fully spatial discretization in the vicinity of this interface zone, an interface model was proposed within the framework of micropolar theory by introducing discontinuous approximation. A fracture description was used to represent the microscopic failure progress inside the interface. The micropolar interface model was then numerically implemented with the finite element method. As an application, the interface behavior of a packaging system with anisotropic conductive adhesive (ACA) joint was analyzed, demonstrating its applicability and great efficiency.
基金Supported by Education Ministry's New Century Excellent Talents Supporting Plan(NCET-12-0659)Project of Outstanding Technological Educators of Governor of Guizhou([2012]71)+3 种基金Project of Low Carbon Technology Plan of Guiyang(2012205)Project of Science and Technology Foundation of Guiyang(LKM[2012]05)Special Research Projects of High Level Talents of Guizhou Province(TZJF-2011-44)Research Projects of Guizhou Minzu University([2014]02)
文摘By applying the segmentation and composition principles of ecosystem,the structure and interface of earth ecosystem are fully elaborated,and corresponding model diagrams are established to display its composition and interconversion. The research finds that earth ecosystem includes three sub-ecosystems： terrestrial ecosystem,marine ecosystem and atmospheric ecosystem. The impact sequence of sub-ecosystems on earth ecosystem is atmospheric ecosystem 〉 marine ecosystem 〉 terrestrial ecosystem. Based on the segmentation and composition principles of ecosystem and the application of earth ecosystem structure and interface,we give new explanations to Taoism and Taiji with the eight diagrams,which contributes to theoretical research of natural science.
基金This work was financially supported by the National Natural Science Foundation of China (No.10272003) and the Talent Foundationof University of Science & Technology Beijing.
文摘The influences of interphase on dynamic effective properties of composites reinforced by randomly dispersed spherical particles were studied. A thin homogeneous elastic interphase with different shear and bulk moduli, located between the reinforced particle and the host matrix, was introduced to model the interfacial bonding state. The effects of such an interphase on the coherent plane waves were studied numerically. Numerical simulations were carried out for SiC-Al composites with four typical cases of interphase. It was found that the property of interphase has significant influences on the effective propagation constants of coherent waves and the dynamic effective elastic moduli of the composites. The influences on the coherent longitudinal wave and the coherent shear waves were different and dependent upon the frequency range. Moreover, several imperfect interface models, i.e., the spring model, mass model, and spring-mass model, were studied numerically and compared with the interphase model, It was found that the spring model is a more suitable model than the mass model for the light and weak interphase whereas the mass model is a more suitable model than the spring model for the heavy and strong interphase.
基金Scientific Research Fund of Institute of Engineering Mechanics,China Earthquake Administration under Grant No.2016A01the National Key Research and Development Plan under Grant No.2016YFC0701108the National Natural Science Foundation of China under Grant Nos.51238012,51322801)
文摘The development of a powerful numerical model to simulate the fracture behavior of concrete material has long been one of the dominant research areas in earthquake engineering. A reliable model should be able to adequately represent the discontinuous characteristics of cracks and simulate various failure behaviors under complicated loading conditions. In this paper, a numerical formulation, which incorporates a sophisticated rigid-plastic interface constitutive model coupling cohesion softening, contact, friction and shear dilatation into the XFEM, is proposed to describe various crack behaviors of concrete material. An effective numerical integration scheme for accurately assembling the contribution to the weak form on both sides of the discontinuity is introduced. The effectiveness of the proposed method has been assessed by simulating several well-known experimental tests. It is concluded that the numerical method can successfully capture the crack paths and accurately predict the fracture behavior of concrete structures. The influence ofmode-Ⅱ parameters on the mixed-mode fracture behavior is further investigated to better determine these parameters.
基金This project is supported by Provincial Science & Technology Projoct of Heilongjiang, China (No. GB05A501).
文摘Aiming at the characteristics of modularity and reconfigurable in open architecture computer numerical control （CNC） system, the open architecture CNC system, Harbin Institute of Tech- nology computer numerical control （HITCNC）, is researched and manufactured based on the interface standards. The system＇s external interfaces are coincident with the corresponding international standards, and the internal interfaces follow the open modular architecture controller （OMAC） agreement. In the research and manufacturing process, object-oriented technology is used to ensure the openness of the HITCNC, and static programming is applied in the CNC system according to the idea of modularization disassembly. The HITCNC also actualizes real-time and unreal-time modules adopting real-time dynamical linked library （RTDLL） and component object model （COM）. Finite state ma- chine （FSM） is adopted to do dynamically modeling of HITCNC. The complete separation between the software and the hardware is achieved in the HITCNC by applying the SoftSERCANS technique. The application of the above key techniques decreases the programming workload greatly, and uses software programs replacing hardware functions, which offers plenty technique ensures for the openness of HITCNC. Finally, based on the HITCNC, a three-dimensional milling system is established. On the system, series experiments are done to validate the expandability and interchangeability of HITCNC. The results of the experiments show that the established open architecture CNC system HITCNC is correct and feasible, and has good openness.
基金This work was supported by the National Science Center,Poland(Narodowe Centrum Nauki,Polska)in the project“Statistical modeling of turbulent two-fluid flows with interfaces”(Grant No.2016/21/B/ST8/01010,ID:334165).
文摘This paper reviews differences between the deterministic(sharp and diffuse)and statistical models of the interphase region between the two-phases.In the literature this region is usually referred to as the(macroscopic)interface.Therein,the mesoscopic interface that is defined at the molecular level and agitated by the thermal fluctuations is found with nonzero probability.For this reason,in this work,the interphase region is called the mesoscopic intermittency/transition region.To this purpose,the first part of the present work gives the rationale for introduction of the mesoscopic intermittency region statistical model.It is argued that classical(deterministic)sharp and diffuse models do not explain the experimental and numerical results presented in the literature.Afterwards,it is elucidated that a statistical model of the mesoscopic intermittency region(SMIR)combines existing sharp and diffuse models into a single coherent framework and explains published experimental and numerical results.In the second part of the present paper,the SMIR is used for the first time to predict equilibrium and nonequilibrium two-phase flow in the numerical simulation.To this goal,a two-dimensional rising gas bubble is studied;obtained numerical results are used as a basis to discuss differences between the deterministic and statistical models showing the statistical description has a potential to account for the physical phenomena not previously considered in the computer simulations.
基金The authors sincerely thank the National Natural Science Foundation of China(Grant Nos.U20A20277,52150610494,52104295,52011530180 and 52050410341)Research Fund for Central Universities(Grant Nos.N2125016 and N2025025)Young Elite Scientists Sponsorship Program by CAST(YESS)(Grant No.2021-2023QNRC001).
文摘Submerged arc welding process has been simulated to investigate the molten pool features of EH36 shipbuilding steel.One case only involved the surface tension model,and another one involved both the surface tension model and the interface tension model.The role of interface tension during welding is revealed,and the evolution of molten pool morphology is understood by comparing the surface temperature distribution,surface tension and interface tension distribution,and the streamline of the molten pool for the two cases.When the interface tension model is disregarded,a flow conducive to the outward expansion is formed in the surface area of the molten pool,resulting in a small weld depth-to-width ratio.After applying the interface tension model,the expanding outward flow is restrained,which leads to a deep penetration morphology with a large weld depth-to-width ratio due to the inward flow governed by the Marangoni forces.The simulation results involving the interface tension model have been verified with satisfactory predictability.
