The influence of Impedance Boundary Condition (IBC) on transonic compressors is investigated. A systematic input–output analytical framework is developed, which treats the nonlinearities as unknown forcing terms. The...The influence of Impedance Boundary Condition (IBC) on transonic compressors is investigated. A systematic input–output analytical framework is developed, which treats the nonlinearities as unknown forcing terms. The framework is validated through the experiments of rotating inlet distortion within a low-speed compressor. The input–output method is subsequently applied to transonic compressors, including NASA Rotor37 and Stage35, wherein impedance optimization is studied along with the exploration of its fundamental mechanisms. The IBC is employed to model the effect of Casing Treatment (CT). The optimal complex impedance values are determined through predicted results and tested across a range of circumferential modes and forcing frequencies. The IBC significantly reduces the energy and Reynolds stress gain, notably at the first-order circumferential mode and within the Rotor Rotating Frequency (RRF) range. Output modes reveal that transonic compressors with fine-tuned impedance values exhibit a more confined perturbation distribution and redistribute the perturbations compared to the uncontrolled case. Additionally, the roles of resistance and reactance are elucidated through input–output analysis, and resistance determines the energy transfer direction between flow and pressure waves and modulates the amplitude, whereas reactance modifies the phase relationships and attenuates the perturbations.展开更多
Stray light has a significant effect on the overall performance of telescopes,particularly for infrared solar telescopes,in which internal thermal radiation causes additional stray light sources.We establish a 3-dimen...Stray light has a significant effect on the overall performance of telescopes,particularly for infrared solar telescopes,in which internal thermal radiation causes additional stray light sources.We establish a 3-dimensional model using stray light theory and the real opto-mechanical structure of the Accurate Infrared Magnetic field measurements of the Sun(AIMS)telescope.We use the stray light ratio(i.e.,the ratio of stray light energy reaching the detector to the light energy used for observations)to evaluate the imaging performance of the telescope.We analyze both thermal and non-thermal sources of stray light to comprehensively study the visible,8-10μm,and Fourier transform infrared systems of the telescope,finding stray light ratios of 9.31×10^(-6)in the visible system,2.83×10^(-4)in the 8-10μm system,and 1.54×10^(-4)in the Fourier transform infrared system.This verifies that the opto-mechanical system design of the telescope can effectively suppress stray light,benefiting both imaging and magnetic field observations.展开更多
Soil desiccation cracking is ubiquitous in nature and has significantpotential impacts on the engineering geological properties of soils.Previous studies have extensively examined various factors affecting soil cracki...Soil desiccation cracking is ubiquitous in nature and has significantpotential impacts on the engineering geological properties of soils.Previous studies have extensively examined various factors affecting soil cracking behavior through a numerous small-sample experiments.However,experimental studies alone cannot accurately describe soil cracking behavior.In this study,we firstly propose a modeling framework for predicting the surface crack ratio of soil desiccation cracking based on machine learning and interpretable analysis.The framework utilizes 1040 sets of soil cracking experimental data and employs random forest(RF),extreme gradient boosting(XGBoost),and artificialneural network(ANN)models to predict the surface crack ratio of soil desiccation cracking.To clarify the influenceof input features on soil cracking behavior,feature importance and Shapley additive explanations(SHAP)are applied for interpretability analysis.The results reveal that ensemble methods(RF and XGBoost)provide better predictive performance than the deep learning model(ANN).The feature importance analysis shows that soil desiccation cracking is primarily influencedby initial water content,plasticity index,finalwater content,liquid limit,sand content,clay content and thickness.Moreover,SHAP-based interpretability analysis further explores how soil cracking responds to various input variables.This study provides new insight into the evolution of soil cracking behavior,enhancing the understanding of its physical mechanisms and facilitating the assessment of potential regional development of soil desiccation cracking.展开更多
This study unfolds an innovative approach aiming to address the critical role of building design in global energy consumption, focusing on optimizing the Window-to-Wall Ratio (WWR), since buildings account for approxi...This study unfolds an innovative approach aiming to address the critical role of building design in global energy consumption, focusing on optimizing the Window-to-Wall Ratio (WWR), since buildings account for approximately 30% of total energy consumed worldwide. The greatest contributors to energy expenditure in buildings are internal artificial lighting and heating and cooling systems. The WWR, determined by the proportion of the building’s glazed area to its wall area, is a significant factor influencing energy efficiency and minimizing energy load. This study introduces the development of a semi-automated computer model designed to offer a real-time, interactive simulation environment, fostering improving communication and engagement between designers and owners. The said model serves to optimize both the WWR and building orientation to align with occupants’ needs and expectations, subsequently reducing annual energy consumption and enhancing the overall building energy performance. The integrated model incorporates Building Information Modeling (BIM), Virtual Reality (VR), and Energy Analysis tools deployed at the conceptual design stage, allowing for the amalgamation of owners’ inputs in the design process and facilitating the creation of more realistic and effective design strategies.展开更多
According to the principles of simultaneous equilibrium and mass equilibrium, a series of thermodynamic equilibrium equations in Ni（II）-Co（II）-C2O4^2--NH3-NH4^＋-H2O system at ambient temperature were deduced. The...According to the principles of simultaneous equilibrium and mass equilibrium, a series of thermodynamic equilibrium equations in Ni（II）-Co（II）-C2O4^2--NH3-NH4^＋-H2O system at ambient temperature were deduced. The diagrams of logarithm ion concentrations versus pH values at different solution compositions were drawn. The results show that Ni^2＋ and Co^2＋ can completely precipitate at pH less than 5.0 and the predefined Ni/Co ratios can be well kept in the precursor. The precursor morphology is granular aggregation. However, rod aggregation precursor is obtained in the pH range of 5.0-8.0, and fibre-shape precursor is got at pH value higher than 8.0. The Ni/Co ratios in the above two precursors are not reproduced as that in the feed due to the formhtion of multi-coordinated Ni（NH3）n^2＋ and Co（NH3）n^2＋ （n=1-6）. Modification of precipitation medium is favorable for the precursors to keep the predefined Ni/Co ratios of the feed in the pH range of 2.0-8.6. Meanwhile, the precursors with fibrous morphology can be obtained.展开更多
A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci- plinary coupled numerical c...A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci- plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound- ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti- tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex- ible wings.展开更多
Global production networks have become the most important organizational platforms for coordinating international production activities,and their evolution patterns profoundly affect value distribution across the worl...Global production networks have become the most important organizational platforms for coordinating international production activities,and their evolution patterns profoundly affect value distribution across the world.In this study,we shall firstly carry out an in-depth quantitative research to analyze the patterns and evolution of global production networks,using a long time-sequenced multi-region input-output table and the network analysis approach.Then based on the method of value-added decomposition,we will develop an index system to measure the degree of participation of regions in global production networks.Finally,we will try to identify the factors affecting the degree of participation of countries in global production networks by constructing a regression model.The results show that from 1995 to 2015,the evolution of global production networks measured by input-output linkages experienced four stages:expansion,contraction,re-expansion,and re-contraction.In addition,the core communities of global production networks evolved from two major production communities(Europe and the Americas)to three pillars(Europe,Americas,and Asia)while more segmented communities are mainly affected by geographical proximity.The latter consists of European,North American,South American,African and Asian communities.The evolution of the global production network pattern primarily manifests as a process of cooperation strengthening or weakening among communities,based on changes in the external environment and the need for individual development strategies.Meanwhile,the United States,Germany,and the United Kingdom have consistently ranked among the top entities in global production networks,whereas China,Russia,and Southeast Asia have the fastest rises in ranking.In addition,government efficiency,resources endowment,infrastructure conditions and technology levels play important roles in the participation in global production networks.展开更多
A new method for quantitative phase analysis is proposed by using X-ray diffraction multi-peak match intensity ratio. This method can obtain the multi-peak match intensity ratio among each phase in the mixture sample ...A new method for quantitative phase analysis is proposed by using X-ray diffraction multi-peak match intensity ratio. This method can obtain the multi-peak match intensity ratio among each phase in the mixture sample by using all diffraction peak data in the mixture sample X-ray diffraction spectrum and combining the relative intensity distribution data of each phase standard peak in JCPDS card to carry on the least square method regression analysis. It is benefit to improve the precision of quantitative phase analysis that the given single line ratio which is usually adopted is taken the place of the multi-peak match intensity ratio and is used in X-ray diffraction quantitative phase analysis of the mixture sample. By analyzing four-group mixture sample, adopting multi-peak match intensity ratio and X-ray diffraction quantitative phase analysis principle of combining the adiabatic and matrix flushing method, it is tested that the experimental results are identical with theory.展开更多
Brazilian disc tests were undertaken on a number of red sandstone samples with different water absorption ratios.The tensile strength of the red sandstone decreases as the water absorption ratio increases.The fracture...Brazilian disc tests were undertaken on a number of red sandstone samples with different water absorption ratios.The tensile strength of the red sandstone decreases as the water absorption ratio increases.The fracture surfaces of failed red sandstone discs were scanned by Talysurf CLI 2000.With the aid of Talymap Gold software,based on ISO25178,a set of statistical parameters was obtained for the fracture surfaces.The maximum peak height(S_p),maximum pit height(S_v) and maximum height(S_z) of the fracture surfaces exhibited the same decreasing trend with increasing water absorption.Sa and Sku values for the fracture surfaces showed a downward trend as the water absorption ratio increased.The fractal dimensions of fracture surfaces were calculated and found to decrease as the water absorption ratio increased.Through analysis of PSD curves,the smallest dominant wavelength was observed to reflect the roughness of the fracture surfaces.Additionally,the results suggest that the roughness of fracture surfaces becomes small as the water absorption ratio increases.展开更多
A ratio approach based on the simple ratio test associated with the terms of homotopy series was proposed by the author in the previous publications.It was shown in the latter through various comparative physical mode...A ratio approach based on the simple ratio test associated with the terms of homotopy series was proposed by the author in the previous publications.It was shown in the latter through various comparative physical models that the ratio approach of identifying the range of the convergence control parameter and also an optimal value for it in the homotopy analysis method is a promising alternative to the classically used h-level curves or to the minimizing the residual(squared)error.A mathematical analysis is targeted here to prove the equivalence of both the ratio approach and the traditional residual approach,especially regarding the root-finding problems via the homotopy analysis method.Examples are provided to further justify this.Moreover,it is conjectured that every nonlinear differential equation can be considered as a root-finding problem by plugging a parameter in it from a physical viewpoint.Two examples from the boundary and initial and value problems are provided to verify this assertion.Hence,besides the advantages as deciphered in the previous publications,the feasibility of the ratio approach over the traditional residual approach is made clearer in this paper.展开更多
This study aimed to explore the application of surface-enhanced Raman scattering(SERS)in the rapid diagnosis of gastric cancer.The SERS spectra of 68 serum samples from gastric cancer patients and healthy volunteers w...This study aimed to explore the application of surface-enhanced Raman scattering(SERS)in the rapid diagnosis of gastric cancer.The SERS spectra of 68 serum samples from gastric cancer patients and healthy volunteers were acquired.The characteristic ratio method(CRM)and principal component analysis(PCA)were used to differentiate gastric cancer serum from normal serum.Compared with healthy volunteers,the serum SERS intensity of gastric cancer patients was relatively high at 722 cm^(-1),while it was relatively low at 588,644,861,1008,1235,1397,1445 and 1586 cm^(-1).These results indicated that the relative content of nucleic acids in the serum of gastric cancer patients rises while the relative content of amino acids and carbohydrates decreases.In PCA,the sensitivity and specificity of discriminating gastric cancer were 94.1%and 94.1%,respectively,with the accuracy of 94.1%.Based on the intensity ratios of four characteristic peaks at 722,861,1008 and 1397 cm^(-1),CRM presented the diagnostic sensitivity and specificity of 100%and 97.4%,respectively,and the accuracy of 98.5%.Therefore,the three peak intensity ratios of I_(722)/I_(861),I_(722)/I_(1008)and I_(722)/I_(1397)can be considered as biologicalfingerprint information for gastric cancer diagnosis and can rapidly and directly reflect the physiological and pathological changes associated with gastric cancer development.This study provides an important basis and standards for the early diagnosis of gastric cancer.展开更多
The elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus(H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying...The elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus(H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying ratio H/E on the surface were studied by the experiment. The results show that the penetration depth, contact radius, plastic pile-up and the degree of elastic recovery depend strongly on the ratio H/E. Moreover, graphs were established to describe the relationship between the elastic-plastic indentation parameters and H/E. The established graphs can be used to predict the H/E of materials when compared with experimental data.展开更多
This research proposes an integrated approach to the Data Envelopment Analysis (DEA) and Analytic Hierarchy Process (AHP) methodologies for ratio analysis. According to this, we compute two sets of weights of ratios i...This research proposes an integrated approach to the Data Envelopment Analysis (DEA) and Analytic Hierarchy Process (AHP) methodologies for ratio analysis. According to this, we compute two sets of weights of ratios in the DEA framework. All ratios are treated as outputs without explicit inputs. The first set of weights represents the most attainable efficiency level for each Decision Making Unit (DMU) in comparison to the other DMUs. The second set of weights represents the relative priority of output-ratios using AHP. We assess the performance of each DMU in terms of the relative closeness to the priority weights of output-ratios. For this purpose, we develop a parametric goal programming model to measure the deviations between the two sets of weights. Increasing the value of a parameter in a defined range of efficiency loss, we explore how much the deviations can be improved to achieve the desired goals of the decision maker.This may result in various ranking positions for each DMU in comparison to the other DMUs. An illustrated example of eight listed companies in the steel industry of China is used to highlight the usefulness of the proposed approach.展开更多
As one of the important indicators of spectrometer,signal-to-noise ratio(SNR)reflects the ability of spectrometer to detect weak signals.To investigate the influence of SNR on the prediction accuracy of spectral analy...As one of the important indicators of spectrometer,signal-to-noise ratio(SNR)reflects the ability of spectrometer to detect weak signals.To investigate the influence of SNR on the prediction accuracy of spectral analysis,we first introduce the major factors affecting the spectral SNR.Taking green tea as an example,the influence of spectral SNR on the prediction accuracy of the origin identification model is analyzed by experiments.At the same time,the relationship between the spectral SNR and prediction accuracy of spectral analysis model is fitted.Based on this,the common methods for improving the spectral SNR are discussed.The results show that the accuracy of the prediction set model first decreases slowly,then decreases linearly,and finally tends to be flat as the spectral SNR decreases.Through calculation,in order to achieve the prediction accuracy of prediction model reaching 90%and 85%,the spectral SNR is required to be higher than 23.42 dB and 21.16 dB,respectively.The overall results provide certain parameters support for the development of new online analytical spectroscopic instruments,especially for the technical indicators of SNR.展开更多
The paper assesses the economic impacts of the natural forest protection program （NFPP） on the economy of Yunnan Province, China.in terms of gross output, value added,employment, and household income. An inputoutput...The paper assesses the economic impacts of the natural forest protection program （NFPP） on the economy of Yunnan Province, China.in terms of gross output, value added,employment, and household income. An inputoutput model is developed to estimate NFPP＇s economic impacts by means of backward linkages in the forestry sector and logging and haudage sector. It is found than the NFPP has positive impacts on gross output, value added and houschold income in the initial year, but has significantly negative impacts on the regional economy in the following years as the investment decreases.展开更多
Based on the perception of flood risk factors derived from the lessons learned by the main stakeholders, namely the members of the National Emergency Response Plan (ORSEC) and the people affected by floods in the stud...Based on the perception of flood risk factors derived from the lessons learned by the main stakeholders, namely the members of the National Emergency Response Plan (ORSEC) and the people affected by floods in the study area (Thies, Senegal), this work consists of modelling the flood risk using Hierarchical Process Analysis (HPA). This modelling made it possible to determine the coherence index (CI) and the coherence ratio, which were evaluated respectively at 0.27% and 5% according to the perception of the members of the ORSEC Plan, and at 0.28% and 5% according to the perception of the disaster victims. These results show that the working approach is coherent and acceptable. We then carried out Hierarchical Fuzzy Process Analysis (HFPA), an extension of HFPA, which seeks to minimize the margins of error. FPHA uses fuzzification of perception contributions, interference rules and defuzzification to determine the Net Flood Risk Index (NFRI). Integrated with ArcGIS software, the NFRI is used to generate flood risk maps that reveal a high risk of vulnerability of the main outlets occupied by human settlements.展开更多
A unified structural model for high-aspect-ratio composite wing with arbitrary cross-section is developed. Two types of lay-ups of the composite wing, namely, circumferentially uniform stiffness （CUS） configuration ...A unified structural model for high-aspect-ratio composite wing with arbitrary cross-section is developed. Two types of lay-ups of the composite wing, namely, circumferentially uniform stiffness （CUS） configuration and circumferentially asymmetric stiffness （CAS） configuration, are investigated. The present structural modeling method is validated through ANSYS FEM software for the case of a composite box beam. Then, the case of a single-cell composite wing with NACA0012 airfoil shape is considered. To investigate the aeroelastic problem of high-aspect-ratio composite wings, the linear ONERA aerodynamic model is used to model the unsteady aerodynamic loads under the case of small angle of attack. Finally, flutter speeds of the high-aspect-ratio wing with various composite ply angles are determined by using U-g method.展开更多
We investigate the weight-based food self-sufficiency ratio (WSSR) for Japan over a 50-year period (1961-2011) by applying factorial component analysis technique in order to measure the changes of the WSSR quantitativ...We investigate the weight-based food self-sufficiency ratio (WSSR) for Japan over a 50-year period (1961-2011) by applying factorial component analysis technique in order to measure the changes of the WSSR quantitatively. Quantitative data analysis is employed to determine the drivers of those changes. Numerical results show that Japan experienced a drastic decline in its food self-sufficiency ratio (FSSR) during the above period. The factorial component analysis shows that such a decline was caused by the changes in the FSSR of the food groups/items, not in the quantity of the food supply. A number of characteristics of those changes are presented and a list of major food groups that have major impacts on the changes is constructed. The findings in this paper reiterate the alarming food security problem in Japan and provide clear insight into the causes of this problem. The findings in this study pick up where previous studies have left off, aid the food-related policy-making process and identify new ideas for future food research.展开更多
Wenchuan earthquake damage survey displayed the major structures of buildings suffered only small damages,but it was common that infill walls suffered heavy damages or even collapse. To study the failure forms and col...Wenchuan earthquake damage survey displayed the major structures of buildings suffered only small damages,but it was common that infill walls suffered heavy damages or even collapse. To study the failure forms and collapse mechanism of infill walls in an earthquake,the influence of opening or length-to-height ratio on shake-resisting capability of filling walls was analyzed,and measures to improve the anti-collapse ability of infill walls were put forwaed. The numerical simulations on collapse process in earthquake were carried out by using ABAQUS software. We used 5 single story and single span models. It is revealed that the rigidity and compressive capacity of infill walls are reduced because of the infill walls with holes and the increases of length-to-height ratios. Adding constructional columns and horizontal beams can ensure structural integrity and improve the anti-collapse ability of the wall.展开更多
Recycling of industrial waste is one of the effective ways to overcome their disposal problem. Ash produced by thermal power plants and lime sludge produced by paper mills require huge disposal land and may create env...Recycling of industrial waste is one of the effective ways to overcome their disposal problem. Ash produced by thermal power plants and lime sludge produced by paper mills require huge disposal land and may create environmental problems such as dusting and leaching of harmful heavy metals. Stabilization of the ash can improve its engineering properties and address the environmental problems. This paper reports the laboratory test results of a Class F pond ash stabilized with lime(2%, 4%, 6% and 8% by weight)alone and in combination with lime sludge(5%, 10% and 15% by weight). The X-ray diffraction(XRD) and scanning electron micrograph(SEM) tests were also performed to identify the possible formation of crystalline phases after stabilization. The effects of lime sludge on the unsoaked and soaked bearing ratios of pond ash with different lime contents, after 7 d, 28 d and 45 d of curing, were observed. Test results indicated that the bearing ratio increased considerably up to a 4% lime content which can be taken as the optimum lime content. Further increase in lime content increased bearing ratio gradually but at a slower rate. The effect of lime sludge was more pronounced at the optimum lime content,particularly at a low curing period. Lime sludge improved the bearing ratio in soaked condition significantly. Leachate analysis of stabilized ash was performed using toxicity characteristic leaching procedure(TCLP-1311) method. The concentrations of toxic elements Zn, Cu, Cd, Ni and Cr in the stabilized mixes were lower than those in the unstabilized waste. The results indicated that the pond ash-lime-lime sludge mixes have potential application as road subbase material.展开更多
基金co-supported by the National Natural Science Foundation of China(Nos.52325602,52306036 and 52306035)the National Science and Technology Major Project of China(No.Y2022-II-0003-0006 and Y2022-II-0002-0005)+1 种基金the project funded by China Postdoctoral Science Foundation(No.2022M720346)supported by the Key Laboratory of Pre-Research Management Centre of China(No.6142702200101).
文摘The influence of Impedance Boundary Condition (IBC) on transonic compressors is investigated. A systematic input–output analytical framework is developed, which treats the nonlinearities as unknown forcing terms. The framework is validated through the experiments of rotating inlet distortion within a low-speed compressor. The input–output method is subsequently applied to transonic compressors, including NASA Rotor37 and Stage35, wherein impedance optimization is studied along with the exploration of its fundamental mechanisms. The IBC is employed to model the effect of Casing Treatment (CT). The optimal complex impedance values are determined through predicted results and tested across a range of circumferential modes and forcing frequencies. The IBC significantly reduces the energy and Reynolds stress gain, notably at the first-order circumferential mode and within the Rotor Rotating Frequency (RRF) range. Output modes reveal that transonic compressors with fine-tuned impedance values exhibit a more confined perturbation distribution and redistribute the perturbations compared to the uncontrolled case. Additionally, the roles of resistance and reactance are elucidated through input–output analysis, and resistance determines the energy transfer direction between flow and pressure waves and modulates the amplitude, whereas reactance modifies the phase relationships and attenuates the perturbations.
基金supported by National Natural Science Foundation of China(12473086 and 11427901)National Key Research and Development Program of China(2021YFA1600500)Youth Innovation Promotion Association of the Chinese Academy of Sciences(2022057).
文摘Stray light has a significant effect on the overall performance of telescopes,particularly for infrared solar telescopes,in which internal thermal radiation causes additional stray light sources.We establish a 3-dimensional model using stray light theory and the real opto-mechanical structure of the Accurate Infrared Magnetic field measurements of the Sun(AIMS)telescope.We use the stray light ratio(i.e.,the ratio of stray light energy reaching the detector to the light energy used for observations)to evaluate the imaging performance of the telescope.We analyze both thermal and non-thermal sources of stray light to comprehensively study the visible,8-10μm,and Fourier transform infrared systems of the telescope,finding stray light ratios of 9.31×10^(-6)in the visible system,2.83×10^(-4)in the 8-10μm system,and 1.54×10^(-4)in the Fourier transform infrared system.This verifies that the opto-mechanical system design of the telescope can effectively suppress stray light,benefiting both imaging and magnetic field observations.
基金supported by the National Key Research and Development Program of China(Grant Nos.2023YFC3707900 and 2024YFC3012700)the National Natural Science Foundation of China(Grant No.42230710).
文摘Soil desiccation cracking is ubiquitous in nature and has significantpotential impacts on the engineering geological properties of soils.Previous studies have extensively examined various factors affecting soil cracking behavior through a numerous small-sample experiments.However,experimental studies alone cannot accurately describe soil cracking behavior.In this study,we firstly propose a modeling framework for predicting the surface crack ratio of soil desiccation cracking based on machine learning and interpretable analysis.The framework utilizes 1040 sets of soil cracking experimental data and employs random forest(RF),extreme gradient boosting(XGBoost),and artificialneural network(ANN)models to predict the surface crack ratio of soil desiccation cracking.To clarify the influenceof input features on soil cracking behavior,feature importance and Shapley additive explanations(SHAP)are applied for interpretability analysis.The results reveal that ensemble methods(RF and XGBoost)provide better predictive performance than the deep learning model(ANN).The feature importance analysis shows that soil desiccation cracking is primarily influencedby initial water content,plasticity index,finalwater content,liquid limit,sand content,clay content and thickness.Moreover,SHAP-based interpretability analysis further explores how soil cracking responds to various input variables.This study provides new insight into the evolution of soil cracking behavior,enhancing the understanding of its physical mechanisms and facilitating the assessment of potential regional development of soil desiccation cracking.
文摘This study unfolds an innovative approach aiming to address the critical role of building design in global energy consumption, focusing on optimizing the Window-to-Wall Ratio (WWR), since buildings account for approximately 30% of total energy consumed worldwide. The greatest contributors to energy expenditure in buildings are internal artificial lighting and heating and cooling systems. The WWR, determined by the proportion of the building’s glazed area to its wall area, is a significant factor influencing energy efficiency and minimizing energy load. This study introduces the development of a semi-automated computer model designed to offer a real-time, interactive simulation environment, fostering improving communication and engagement between designers and owners. The said model serves to optimize both the WWR and building orientation to align with occupants’ needs and expectations, subsequently reducing annual energy consumption and enhancing the overall building energy performance. The integrated model incorporates Building Information Modeling (BIM), Virtual Reality (VR), and Energy Analysis tools deployed at the conceptual design stage, allowing for the amalgamation of owners’ inputs in the design process and facilitating the creation of more realistic and effective design strategies.
基金Project (20090162120080) supported by Research Fund for the Doctoral Program of Higher Education of China Project (20070410989) supported by China Postdoctoral Science Foundation+1 种基金 Project (2010FJ3012) supported by the Program of Science and Technology of Hunan Province, China Project (09JJ4028) supported by Natural Science Foundation of Hunan Province, China
文摘According to the principles of simultaneous equilibrium and mass equilibrium, a series of thermodynamic equilibrium equations in Ni（II）-Co（II）-C2O4^2--NH3-NH4^＋-H2O system at ambient temperature were deduced. The diagrams of logarithm ion concentrations versus pH values at different solution compositions were drawn. The results show that Ni^2＋ and Co^2＋ can completely precipitate at pH less than 5.0 and the predefined Ni/Co ratios can be well kept in the precursor. The precursor morphology is granular aggregation. However, rod aggregation precursor is obtained in the pH range of 5.0-8.0, and fibre-shape precursor is got at pH value higher than 8.0. The Ni/Co ratios in the above two precursors are not reproduced as that in the feed due to the formhtion of multi-coordinated Ni（NH3）n^2＋ and Co（NH3）n^2＋ （n=1-6）. Modification of precipitation medium is favorable for the precursors to keep the predefined Ni/Co ratios of the feed in the pH range of 2.0-8.6. Meanwhile, the precursors with fibrous morphology can be obtained.
基金supported by the National Natural Science Foundation of China(Nos.11302011,11172025)the National Natural Science Foundation for Youth of China(No.11402013)
文摘A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci- plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound- ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti- tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex- ible wings.
基金Strategic Priority Research Program of Chinese Academy of Sciences,No.XDA20080000National Natural Science Foundation of China,No.41901154。
文摘Global production networks have become the most important organizational platforms for coordinating international production activities,and their evolution patterns profoundly affect value distribution across the world.In this study,we shall firstly carry out an in-depth quantitative research to analyze the patterns and evolution of global production networks,using a long time-sequenced multi-region input-output table and the network analysis approach.Then based on the method of value-added decomposition,we will develop an index system to measure the degree of participation of regions in global production networks.Finally,we will try to identify the factors affecting the degree of participation of countries in global production networks by constructing a regression model.The results show that from 1995 to 2015,the evolution of global production networks measured by input-output linkages experienced four stages:expansion,contraction,re-expansion,and re-contraction.In addition,the core communities of global production networks evolved from two major production communities(Europe and the Americas)to three pillars(Europe,Americas,and Asia)while more segmented communities are mainly affected by geographical proximity.The latter consists of European,North American,South American,African and Asian communities.The evolution of the global production network pattern primarily manifests as a process of cooperation strengthening or weakening among communities,based on changes in the external environment and the need for individual development strategies.Meanwhile,the United States,Germany,and the United Kingdom have consistently ranked among the top entities in global production networks,whereas China,Russia,and Southeast Asia have the fastest rises in ranking.In addition,government efficiency,resources endowment,infrastructure conditions and technology levels play important roles in the participation in global production networks.
文摘A new method for quantitative phase analysis is proposed by using X-ray diffraction multi-peak match intensity ratio. This method can obtain the multi-peak match intensity ratio among each phase in the mixture sample by using all diffraction peak data in the mixture sample X-ray diffraction spectrum and combining the relative intensity distribution data of each phase standard peak in JCPDS card to carry on the least square method regression analysis. It is benefit to improve the precision of quantitative phase analysis that the given single line ratio which is usually adopted is taken the place of the multi-peak match intensity ratio and is used in X-ray diffraction quantitative phase analysis of the mixture sample. By analyzing four-group mixture sample, adopting multi-peak match intensity ratio and X-ray diffraction quantitative phase analysis principle of combining the adiabatic and matrix flushing method, it is tested that the experimental results are identical with theory.
基金Project(E21527)supported by Open Research Fund Program of Hunan Provincial Key Laboratory of Shale Gas Resource Utilization,Hunan University of Science and Technology,ChinaProjects(51174088,51174228)supported by the National Natural Science Foundation of China+1 种基金Project(2013CB035401)supported by the National Basic Research Program of ChinaProject(2015zzts077)supported by the Fundamental Research Funds for the Central Universities,China
文摘Brazilian disc tests were undertaken on a number of red sandstone samples with different water absorption ratios.The tensile strength of the red sandstone decreases as the water absorption ratio increases.The fracture surfaces of failed red sandstone discs were scanned by Talysurf CLI 2000.With the aid of Talymap Gold software,based on ISO25178,a set of statistical parameters was obtained for the fracture surfaces.The maximum peak height(S_p),maximum pit height(S_v) and maximum height(S_z) of the fracture surfaces exhibited the same decreasing trend with increasing water absorption.Sa and Sku values for the fracture surfaces showed a downward trend as the water absorption ratio increased.The fractal dimensions of fracture surfaces were calculated and found to decrease as the water absorption ratio increased.Through analysis of PSD curves,the smallest dominant wavelength was observed to reflect the roughness of the fracture surfaces.Additionally,the results suggest that the roughness of fracture surfaces becomes small as the water absorption ratio increases.
文摘A ratio approach based on the simple ratio test associated with the terms of homotopy series was proposed by the author in the previous publications.It was shown in the latter through various comparative physical models that the ratio approach of identifying the range of the convergence control parameter and also an optimal value for it in the homotopy analysis method is a promising alternative to the classically used h-level curves or to the minimizing the residual(squared)error.A mathematical analysis is targeted here to prove the equivalence of both the ratio approach and the traditional residual approach,especially regarding the root-finding problems via the homotopy analysis method.Examples are provided to further justify this.Moreover,it is conjectured that every nonlinear differential equation can be considered as a root-finding problem by plugging a parameter in it from a physical viewpoint.Two examples from the boundary and initial and value problems are provided to verify this assertion.Hence,besides the advantages as deciphered in the previous publications,the feasibility of the ratio approach over the traditional residual approach is made clearer in this paper.
基金This work was supported by the Natural Science Foundation of Guangdong Province,China(2018 A0303131000)the project of Academician workstation of Guangdong Province,China(2014B090905001)the Fundamental Research Funds for the Central Universities,China(21617406)and the key project of Scientific and Technological projects of Guang Zhou,China(201604040007,201604020168).
文摘This study aimed to explore the application of surface-enhanced Raman scattering(SERS)in the rapid diagnosis of gastric cancer.The SERS spectra of 68 serum samples from gastric cancer patients and healthy volunteers were acquired.The characteristic ratio method(CRM)and principal component analysis(PCA)were used to differentiate gastric cancer serum from normal serum.Compared with healthy volunteers,the serum SERS intensity of gastric cancer patients was relatively high at 722 cm^(-1),while it was relatively low at 588,644,861,1008,1235,1397,1445 and 1586 cm^(-1).These results indicated that the relative content of nucleic acids in the serum of gastric cancer patients rises while the relative content of amino acids and carbohydrates decreases.In PCA,the sensitivity and specificity of discriminating gastric cancer were 94.1%and 94.1%,respectively,with the accuracy of 94.1%.Based on the intensity ratios of four characteristic peaks at 722,861,1008 and 1397 cm^(-1),CRM presented the diagnostic sensitivity and specificity of 100%and 97.4%,respectively,and the accuracy of 98.5%.Therefore,the three peak intensity ratios of I_(722)/I_(861),I_(722)/I_(1008)and I_(722)/I_(1397)can be considered as biologicalfingerprint information for gastric cancer diagnosis and can rapidly and directly reflect the physiological and pathological changes associated with gastric cancer development.This study provides an important basis and standards for the early diagnosis of gastric cancer.
基金Science Research Foundation of Shanghai Municipal Education Commission (No.06VZ004)
文摘The elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus(H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying ratio H/E on the surface were studied by the experiment. The results show that the penetration depth, contact radius, plastic pile-up and the degree of elastic recovery depend strongly on the ratio H/E. Moreover, graphs were established to describe the relationship between the elastic-plastic indentation parameters and H/E. The established graphs can be used to predict the H/E of materials when compared with experimental data.
文摘This research proposes an integrated approach to the Data Envelopment Analysis (DEA) and Analytic Hierarchy Process (AHP) methodologies for ratio analysis. According to this, we compute two sets of weights of ratios in the DEA framework. All ratios are treated as outputs without explicit inputs. The first set of weights represents the most attainable efficiency level for each Decision Making Unit (DMU) in comparison to the other DMUs. The second set of weights represents the relative priority of output-ratios using AHP. We assess the performance of each DMU in terms of the relative closeness to the priority weights of output-ratios. For this purpose, we develop a parametric goal programming model to measure the deviations between the two sets of weights. Increasing the value of a parameter in a defined range of efficiency loss, we explore how much the deviations can be improved to achieve the desired goals of the decision maker.This may result in various ranking positions for each DMU in comparison to the other DMUs. An illustrated example of eight listed companies in the steel industry of China is used to highlight the usefulness of the proposed approach.
基金Key Research and Development Program of Anhui Province(No.201904a07020073)Science and Technology Foundation of Electronic Test&Measurement Laboratory(No.6142001180307)National Basic Research Program(No.JSJL2018210C003)。
文摘As one of the important indicators of spectrometer,signal-to-noise ratio(SNR)reflects the ability of spectrometer to detect weak signals.To investigate the influence of SNR on the prediction accuracy of spectral analysis,we first introduce the major factors affecting the spectral SNR.Taking green tea as an example,the influence of spectral SNR on the prediction accuracy of the origin identification model is analyzed by experiments.At the same time,the relationship between the spectral SNR and prediction accuracy of spectral analysis model is fitted.Based on this,the common methods for improving the spectral SNR are discussed.The results show that the accuracy of the prediction set model first decreases slowly,then decreases linearly,and finally tends to be flat as the spectral SNR decreases.Through calculation,in order to achieve the prediction accuracy of prediction model reaching 90%and 85%,the spectral SNR is required to be higher than 23.42 dB and 21.16 dB,respectively.The overall results provide certain parameters support for the development of new online analytical spectroscopic instruments,especially for the technical indicators of SNR.
文摘The paper assesses the economic impacts of the natural forest protection program （NFPP） on the economy of Yunnan Province, China.in terms of gross output, value added,employment, and household income. An inputoutput model is developed to estimate NFPP＇s economic impacts by means of backward linkages in the forestry sector and logging and haudage sector. It is found than the NFPP has positive impacts on gross output, value added and houschold income in the initial year, but has significantly negative impacts on the regional economy in the following years as the investment decreases.
文摘Based on the perception of flood risk factors derived from the lessons learned by the main stakeholders, namely the members of the National Emergency Response Plan (ORSEC) and the people affected by floods in the study area (Thies, Senegal), this work consists of modelling the flood risk using Hierarchical Process Analysis (HPA). This modelling made it possible to determine the coherence index (CI) and the coherence ratio, which were evaluated respectively at 0.27% and 5% according to the perception of the members of the ORSEC Plan, and at 0.28% and 5% according to the perception of the disaster victims. These results show that the working approach is coherent and acceptable. We then carried out Hierarchical Fuzzy Process Analysis (HFPA), an extension of HFPA, which seeks to minimize the margins of error. FPHA uses fuzzification of perception contributions, interference rules and defuzzification to determine the Net Flood Risk Index (NFRI). Integrated with ArcGIS software, the NFRI is used to generate flood risk maps that reveal a high risk of vulnerability of the main outlets occupied by human settlements.
文摘A unified structural model for high-aspect-ratio composite wing with arbitrary cross-section is developed. Two types of lay-ups of the composite wing, namely, circumferentially uniform stiffness （CUS） configuration and circumferentially asymmetric stiffness （CAS） configuration, are investigated. The present structural modeling method is validated through ANSYS FEM software for the case of a composite box beam. Then, the case of a single-cell composite wing with NACA0012 airfoil shape is considered. To investigate the aeroelastic problem of high-aspect-ratio composite wings, the linear ONERA aerodynamic model is used to model the unsteady aerodynamic loads under the case of small angle of attack. Finally, flutter speeds of the high-aspect-ratio wing with various composite ply angles are determined by using U-g method.
文摘We investigate the weight-based food self-sufficiency ratio (WSSR) for Japan over a 50-year period (1961-2011) by applying factorial component analysis technique in order to measure the changes of the WSSR quantitatively. Quantitative data analysis is employed to determine the drivers of those changes. Numerical results show that Japan experienced a drastic decline in its food self-sufficiency ratio (FSSR) during the above period. The factorial component analysis shows that such a decline was caused by the changes in the FSSR of the food groups/items, not in the quantity of the food supply. A number of characteristics of those changes are presented and a list of major food groups that have major impacts on the changes is constructed. The findings in this paper reiterate the alarming food security problem in Japan and provide clear insight into the causes of this problem. The findings in this study pick up where previous studies have left off, aid the food-related policy-making process and identify new ideas for future food research.
基金Funded by research programs in Jiangsu(JGJH2008-22)
文摘Wenchuan earthquake damage survey displayed the major structures of buildings suffered only small damages,but it was common that infill walls suffered heavy damages or even collapse. To study the failure forms and collapse mechanism of infill walls in an earthquake,the influence of opening or length-to-height ratio on shake-resisting capability of filling walls was analyzed,and measures to improve the anti-collapse ability of infill walls were put forwaed. The numerical simulations on collapse process in earthquake were carried out by using ABAQUS software. We used 5 single story and single span models. It is revealed that the rigidity and compressive capacity of infill walls are reduced because of the infill walls with holes and the increases of length-to-height ratios. Adding constructional columns and horizontal beams can ensure structural integrity and improve the anti-collapse ability of the wall.
文摘Recycling of industrial waste is one of the effective ways to overcome their disposal problem. Ash produced by thermal power plants and lime sludge produced by paper mills require huge disposal land and may create environmental problems such as dusting and leaching of harmful heavy metals. Stabilization of the ash can improve its engineering properties and address the environmental problems. This paper reports the laboratory test results of a Class F pond ash stabilized with lime(2%, 4%, 6% and 8% by weight)alone and in combination with lime sludge(5%, 10% and 15% by weight). The X-ray diffraction(XRD) and scanning electron micrograph(SEM) tests were also performed to identify the possible formation of crystalline phases after stabilization. The effects of lime sludge on the unsoaked and soaked bearing ratios of pond ash with different lime contents, after 7 d, 28 d and 45 d of curing, were observed. Test results indicated that the bearing ratio increased considerably up to a 4% lime content which can be taken as the optimum lime content. Further increase in lime content increased bearing ratio gradually but at a slower rate. The effect of lime sludge was more pronounced at the optimum lime content,particularly at a low curing period. Lime sludge improved the bearing ratio in soaked condition significantly. Leachate analysis of stabilized ash was performed using toxicity characteristic leaching procedure(TCLP-1311) method. The concentrations of toxic elements Zn, Cu, Cd, Ni and Cr in the stabilized mixes were lower than those in the unstabilized waste. The results indicated that the pond ash-lime-lime sludge mixes have potential application as road subbase material.
