Estuarine processes in the arctic lagoons are among the least studied but important subjects, especially considering the rapid warming of arctic water which may change the length of ice-free period in the summer. In t...Estuarine processes in the arctic lagoons are among the least studied but important subjects, especially considering the rapid warming of arctic water which may change the length of ice-free period in the summer. In this paper, wind-driven exchange flows in the micro-tidal Elson Lagoon of northern Alaska with multiple inlets of contrasting widths and depths are studied with in situ observations, statistical analysis, numerical experiments, a regression model on the basis of dynamics, and remote sensing data. Water velocity profiles were obtained from a bottom deployed acoustic Doppler current profiler(ADCP) in the northwestern Eluitkak Pass connecting the Beaufort Sea to the Elson Lagoon during a 4.9 day ice-free period in the summer of 2013. The subtidal flow is found correlated with wind(R^2 value ～96%). Frequently occurring east, northeast and north winds from the arctic atmospheric high-and low-pressure systems push water from the Beaufort Sea into the lagoon through the wide inlets on the eastern side of the lagoon, resulting in an outward flow against the wind at the narrow northwestern inlet. The counter-wind flow is a result of an uneven wind forcing acting through the asymmetric inlets and depth,an effect of "torque" or vorticity. Under northwest wind, the exchange flow at the northwestern inlet reverses its direction, with inward flows through the upwind northwestern inlet and outward flows through the downwind eastern inlets. A regression model is established based on the momentum equations and Taylor series expansions. The model is used to predict flows in July and August of 2015 and July of 2017, supported by available Landsat satellite images. About 73%–80% of the time the flows at Eluitkak Pass are out of Elson Lagoon for the summer of 2015 and 2017. Numerical experiments are conducted to corroborate the findings and illustrate the effects under various wind conditions. A quasi-steady state balance between wind force and surface pressure gradient is confirmed.展开更多
An inverse reduced-gravity model is used to simulate the deep South China Sea(SCS)circulation.A set of experiments are conducted using this model to study the influence of the Luzon overflow through the two inlets on ...An inverse reduced-gravity model is used to simulate the deep South China Sea(SCS)circulation.A set of experiments are conducted using this model to study the influence of the Luzon overflow through the two inlets on the deep circulation in the northern SCS.Model results suggest that the relative contribution of these inlets largely depends on the magnitude of the input transport of the overflow,but the northern inlet is more efficient than the southern inlet in driving the deep circulation in the northern SCS.When all of the Luzon overflow occurs through the northern inlet the deep circulation in the northern SCS is enhanced.Conversely,when all of the Luzon overflow occurs through the southern inlet the circulation in the northern SCS is weakened.A Lagrangian trajectory model is also developed and applied to these cases.The Lagrangian results indicate that the location of the Luzon overflow likely has impacts upon the sediment transport into the northern SCS.展开更多
In the design of a hypersonic inward-turning inlet by applying the traditional basic flowfield, a reflected shock-wave is formed in the isolator due to the continuous reflection of the cowlreflected shock wave in the ...In the design of a hypersonic inward-turning inlet by applying the traditional basic flowfield, a reflected shock-wave is formed in the isolator due to the continuous reflection of the cowlreflected shock wave in the basic flow-field, which interacts with the boundary layer to produce a considerable influence on the performance of the inlet. Here, a basic flow-field design method that can control the velocity direction at the throat section is developed, and numerical simulations are conducted to demonstrate the effectiveness of this method. The method presented in this paper can achieve the absorption of the reflected waves at the shoulder of the basic flow-field by adjusting the variation law of the center radius in the basic flow-field, and a smooth transition between the compression surface and the isolator can also be produced. The Mach number and total pressure recovery coefficient of the inlet designed according to this method are 3.00 and 0.657, respectively, at design point(the incoming flow Mach number Ma1= 6.0). The results show that with this method, the inlet can efficiently weaken both the reflection of the shock wave and the interaction between the boundary layer and the reflected shock waves, which improves the aerodynamic performance of the inlet.展开更多
The classification performance of model coal mill classifiers with different bottom incoming flow inlets was experimentally and numerically studied.The flow field adjacent to two neighboring impeller blades was measur...The classification performance of model coal mill classifiers with different bottom incoming flow inlets was experimentally and numerically studied.The flow field adjacent to two neighboring impeller blades was measured using the particle image velocimetry technique.The results showed that the flow field adjacent to two neighboring blades with the swirling inlet was significantly different from that with the non-swirling inlet.With the swirling inlet,there was a vortex located between two neighboring blades,while with the nonswirling inlet,the vortex was attached to the blade tip.The vorticity of the vortex with the non-swirling inlet was much lower than that with the swirling inlet.The classifier with the non-swirling inlet demonstrated a larger cut size than that with the swirling inlet when the impeller was stationary(~0 r·min-1).As the impeller rotational speed increased,the cut size of the cases with non-swirling and swirling inlets both decreased,and the one with the non-swirling inlet decreased more dramatically.The values of the cut size of the two classifiers were close to each other at a high impeller rotational speed(≥120 r·min-1).The overall separation efficiency of the classifier with the non-swirling inlet was lower than that with the swirling inlet,and monotonically increased as the impeller rotational speed increased.With the swirling inlet,the overall separation efficiency first increased with the impeller rotational speed and then decreased when the rotational speed was above 120 r·min-1,and the variation trend of the separation efficiency was more moderate.As the initial particle concentration increased,the cut sizes of both swirling and non-swirling inlet cases decreased first and then barely changed.At a low initial particle concentration(b 0.04 kg·m-3),the classifier with the swirling inlet had a larger cut size than that with the non-swirling inlet.展开更多
The relationship between P (spring tidal prism) and A (throat area below mean sea level) is statistically analysed in terms of 29 tidal inlets or bays along the Huanghai Sea (Yellow Sea) and Bohai Sea coasts. For 15 o...The relationship between P (spring tidal prism) and A (throat area below mean sea level) is statistically analysed in terms of 29 tidal inlets or bays along the Huanghai Sea (Yellow Sea) and Bohai Sea coasts. For 15 of these tidal inlets, the best regression equation is A(km2) = 0.845 />(km3)1.20. The analysis shows that C and n are little different from those in the P-A relationship for the inlets of the South China Sea and East China Sea coasts. It is noted that the relationship between P and A is unstable because of the difference in sediment abundance. The study shows that a united P-A relationship can be obtained for the tidal inlets of lagoon type and bay-drowned-valley type, not containing some half-circle shape bays which confront deep water. These half-circle bays do not belong to tidal inlets because they do not have enough sediment abundance and are fairly open.展开更多
In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the...In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the help of this method, the major design concern of balancing the aerodynamic performance against the requirements for efficient propulsion can be well addressed. A novel geometric parametrically modelling method based on a combination of patched class and shape transition（CST） and COONs surface is proposed to represent the configuration, especially a complex configuration with an irregular inlet lip shape. The modelling method enlarges the design space of components on the premise of guaranteeing the configuration integrity via special constraints imposed on the interface across adjacent surfaces. A basic flow inside a cone shaped by a dual-inflection-point generatrix is optimized to generate the inward-turning inlet with improvements of both compression efficiency and flow uniformity. The performance improvement mechanism of this basic flow is the compression velocity variation induced by the variation of the generatrix slope along the flow path. At the design point, numerical simulation results show that the lift-to-drag ratio of the configuration is as high as 5.2 and the inlet works well with a high level of compression efficiency and flow uniformity. The design result also has a good performance on off-design conditions. The achievement of all the design targets turns out that the integration design method proposed in this paper is efficient and practical.展开更多
Aggregation is used to represent the real world in a model at an appropriate level of abstraction.We used the convection-diffusion equation to examine the implications of aggregation progressing from a three-dimension...Aggregation is used to represent the real world in a model at an appropriate level of abstraction.We used the convection-diffusion equation to examine the implications of aggregation progressing from a three-dimensional(3D)spatial description to a model representing a system as a single box that exchanges sediment with the adjacent environment.We highlight how all models depend on some forms of parametric closure,which need to be chosen to suit the scale of aggregation adopted in the model.All such models are therefore aggregated and make use of some empirical relationships to deal with sub-scale processes.One such appropriately aggregated model,the model for the aggregated scale morphological interaction between tidal basin and adjacent coast(ASMITA),is examined in more detail and used to illustrate the insight that this level of aggregation can bring to a problem by considering how tidal inlets and estuaries are impacted by sea level rise.展开更多
The French Atlantic coast seismicity is minor to moderate. Nevertheless, in western （north and central） part of France, the active tectonics related to the south Armorican and the Bay of Biscay context results somet...The French Atlantic coast seismicity is minor to moderate. Nevertheless, in western （north and central） part of France, the active tectonics related to the south Armorican and the Bay of Biscay context results sometimes in shallow earthquakes with magnitude above five （e.g., the Oleron seismic crisis, magnitude （local） = 5.2, 1972）. The Charente region is featured by semi-diurnal tides that reach about six meters in height during the high tide period. Inlets are the main features of the Atlantic margin geomorphology nearby the Charente. Minor tsunamis have been observed and reported in the past. Here, we present a tsunami modelling computed with the TELEMAC package that solves the non linear shallow water equations. This work helps to identify the role of the inlets that characterize the Charente＇s geomorphology on water wave＇s propagation. A tidal model is considered while the tsunami simulation is performed. The modelling results show that the Antioche, the Maumusson and the Pertuis inlets protect the Charente coast from destructive waves.展开更多
Sandy inlets are in a dynamic equilibrium between wave-driven littoral drift acting to close them,and tidal flows keeping them open.Their beds are in a continual state of suspension and deposition,so their bathymetry ...Sandy inlets are in a dynamic equilibrium between wave-driven littoral drift acting to close them,and tidal flows keeping them open.Their beds are in a continual state of suspension and deposition,so their bathymetry and even location are always in flux.Even so,a nearly linear relationship between an inlet’s cross-sectional flow area and the inshore tidal prism is maintained-except when major wind and/or runoff events act to close or widen an inlet.Inlet location can be stabilized by jetties,but dredging may still be necessary to maintain a navigable channel.Armoring with rock large enough to resist erosion can protect an inlet bed or river mouth from excessive storm flow erosion.Armoring can also be used as a stratagem to close inlets.展开更多
The spatiotemporal distribution of soot concentration in aero-engine combustor is important for assessing its combustion performance.Here,we report experimental measurements of soot concentration in terms of Soot Volu...The spatiotemporal distribution of soot concentration in aero-engine combustor is important for assessing its combustion performance.Here,we report experimental measurements of soot concentration in terms of Soot Volume Fraction(SVF)and its spatiotemporal distribution in a single-sector dual-swirl aero-engine combustor using Two-Color Laser-Induced Incandescence(2C-LII).It is shown that soot predominantly forms in the symmetrical vortices of the primary combustion zone,exhibiting a V-type distribution with higher concentration in the lower half of the zone than the upper half,with a small amount distributed in the secondary recirculation zone.Soot emissions at the combustor outlet are relatively low under three typical operating conditions by LII experiments,which is aligned with Smoke Number(SN)from gas analysis.The effect of inlet air temperature on SVF distribution and dynamics in the primary combustion zone is studied,which suggests that the SVF level in the primary combustion zone monotonically increases with the temperature.Meanwhile,the SVF distribution becomes more symmetrical as the inlet temperature increases,although the overall SVF level in the lower half of the zone is still higher.We also investigate the influence of the inlet air pressure on the SVF distribution at the combustor outlet.The soot concentration at the combustor outlet increases with inlet pressure,mainly distributed irregularly across both sides and the center.On both sides,the distribution is continuous,while the center exhibits dot-like and linear patterns.Numerical simulations correlated SVF distribution with the flow field in the primary combustion zone,qualitatively explaining the observed SVF distribution behavior.These results under various conditions can provide valuable insights for improving the performance of this specific combustor and designing high-temperature-rise combustors in the future.展开更多
This study aims to investigate the intricate dynamic characteristics of the high-speed duct during the over-under Turbine-Based Combined Cycle(TBCC)inlet mode transition process while operating in an off-design state ...This study aims to investigate the intricate dynamic characteristics of the high-speed duct during the over-under Turbine-Based Combined Cycle(TBCC)inlet mode transition process while operating in an off-design state under throttled conditions.A typical over-under TBCC inlet,designed for a working Mach number range of 0–6 with a transition Mach number of 3.5,is examined through experimental studies in a supersonic wind tunnel with a freestream Mach number of2.9.The investigation focuses on the complex oscillatory flow and unique hysteresis observed in the mode transition process of the high-speed duct under the mildly throttled condition,utilizing highspeed schlieren and dynamic pressure acquisition system.The findings reveal that the high-speed duct undergoes four distinct oscillation stages akin to those in a higher throttled state during the mode transition,albeit with smaller dominant frequency and energy.Moreover,an irregular alternating“big/little buzz”mode is observed in the early stage of the large oscillation stage.Notably,the mildly throttled state exhibits three intriguing hysteresis properties compared to the unthrottled and higher throttled states.Firstly,hysteresis is observed in the shock train motion stage in the duct before unstart,along with the corresponding inverse process.Subsequently,hysteresis is noted in the unstart and restart of the high-speed duct,with a smaller hysteresis interval than in the unthrottled state.Finally,the hysteresis characteristics of oscillation mode switching and the corresponding inverse process are explored.Based on the analysis,the first two hysteresis phenomena are associated with the formation and dissipation of the separation bubble.The significant adverse pressure gradient constrains the cross-sectional capacity of the channel,rendering the disappearance of the separation bubble more challenging.The hysteresis in oscillation mode switching is linked to not only the channel cross-sectional capacity but also the state of the incoming boundary layer.展开更多
The design of wide-range high-efficiency aerodynamic configurations is one of the most important key technologies in the research of near-space hypersonic vehicles.A double-sided intake configuration with different in...The design of wide-range high-efficiency aerodynamic configurations is one of the most important key technologies in the research of near-space hypersonic vehicles.A double-sided intake configuration with different inlets on the upper and lower surfaces is proposed to adapt to widerange flight.Firstly,the double-sided intake configuration’s design method and flight profile are delineated.Secondly,Computational Fluid Dynamics(CFD)numerical simulation based on multi-Graphics Processing Unit(GPU)parallel computing is adopted to evaluate the vehicle’s performance comprehensively,aiming to verify the feasibility of the proposed scheme.This evaluation encompasses a wide-range basic aerodynamic characteristics,inlet performance,and heat flux at critical locations.The results show that the inlets of the designed integration configuration can start up across Mach number 3.5 to 8.The vehicle possesses multi-point cruising capability by flipping the fuselage.Simultaneously,a 180°rotation of the fuselage can significantly decrease the heat accumulation on the lower surface of the vehicle,particularly at the inlet lip,further decreasing the temperature gradient across the vehicle structure.This study has some engineering value for the aerodynamic configuration design of wide-range vehicles.However,further study reveals that the flow phenomena at the intersection of two inlets are complex,posing potential adverse impacts on propulsion efficiency.Therefore,it is imperative to conduct additional research to delve into this matter comprehensively.展开更多
The utilization of Inlet Guide Vane (IGV) plays a key factor in affecting the instability evolution. Existing literature mainly focuses on the effect of IGV on instability inception that occurs in the rotor region. Ho...The utilization of Inlet Guide Vane (IGV) plays a key factor in affecting the instability evolution. Existing literature mainly focuses on the effect of IGV on instability inception that occurs in the rotor region. However, with the emergence of compressor instability starting from the stator region, the mechanism of various instability inceptions that occurs in different blade rows due to the change of IGV angles should be further examined. In this study, experiments were focused on three types of instability inceptions observed previously in a 1.5-stage axial flow compressor. To analyze the conversion of stall evolutions, the compressor rotating speed was set to 17 160 r/min, at which both the blade loading in the stator hub region and rotor tip region were close to the critical value before final compressor stall. Meanwhile, the dynamic test points with high-response were placed to monitor the pressures both at the stator trailing edges and rotor tips. The results indicate that the variation of reaction determines the region where initial instability occurs. Indeed, negative pre-rotation of the inlet guide vane leads to high-reaction, initiating stall disturbance from the rotor region. Positive pre-rotation results in low-reaction, initiating stall disturbance from the stator region. Furthermore, the type of instability evolution is affected by the radial loading distribution under different IGV angles. Specifically, a spike-type inception occurs at the rotor blade tip with a large angle of attack at the rotor inlet (−2°, −4° and −6°). Meanwhile, the critical total pressure ratio at the rotor tip is 1.40 near stall. As the angle of attack decreases, the stator blade loading reaches its critical boundary, with a value of approximately 1.35. At this moment, if the rotor tip maintains high blade loading similar to the stator hub, the partial surge occurs (0° and +2°);otherwise, the hub instability occurs (+4° and +6°).展开更多
To tackle the instability fault diagnosis challenges in wide-speed-range supersonic inlets,this study proposes an inlet fault decision fusion diagnosis algorithm based on attention mechanism feature fusion,achieving e...To tackle the instability fault diagnosis challenges in wide-speed-range supersonic inlets,this study proposes an inlet fault decision fusion diagnosis algorithm based on attention mechanism feature fusion,achieving efficient diagnosis of instability faults across wide-speed regimes.First,considering the requirement for wall pressure data extraction in mathematical modeling of wide-speed-range inlets,a supersonic inlet reference model is established for computational fluid dynamics(CFD)simulations.Second,leveraging data-driven modeling techniques and support vector machine(SVM)algorithms,a high-precision mathematical model covering wide-speed domains and incorporating instability mechanisms is rapidly developed using CFD-derived inlet wall pressure data.Subsequently,an inlet fault decision fusion diagnosis method is proposed.Pressure features are fused via attention mechanisms,followed by Dempster-Shafer(D-S)evidence theory-based decision fusion,which integrates advantages of multiple intelligent algorithms to overcome the limitations of single-signal diagnosis methods(low accuracy and constrained optimization potential).The simulation results demonstrate the effectiveness of the data-driven wide-speed-range inlet model in achieving high precision and rapid convergence.In addition,the fusion diagnosis algorithm has been shown to attain over 95%accuracy in the detection of instability,indicating an improvement of more than 5%compared to the accuracy of other single fault diagnosis algorithms.This enhancement effectively eliminates the occurrence of missed or false diagnoses,while demonstrates robust performance under operational uncertainties.展开更多
An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(...An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(CT)on the stall margin recovery.An operating cycle is proposed based on the hysteresis effect of harmonic flap oscillation of airfoils and parallel compressor theory to explain the pressure characteristic of the fan under twin swirl inlets.Twin swirls are observed to reduce the stall margin of the fan,and the circumferential location where the spike is detected turns to the intersection area of the twin swirl.The IBC CT is proven to extend the stall margin of the fan for 12.7%–22.3%when subjected to inlet swirls with an efficiency loss of around 1%.The IBC CT helps to reduce the size of the operating cycle of the fan by redistributing the blade loading and adding the system damping to dissipate the perturbation energy.展开更多
Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, La...Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, Laser-Induced Incandescence (LII) has been increasingly applied for soot concentration quantification in various combustion environments such as laminar flame, vehicle exhaust, internal combustion chamber as well as aero-engine combustor. In this work, we experimentally measured the spatial and temporal distribution of SVF using two-color LII technique at the outlet of a single-sector dual-swirl aero-engine model combustor. The effect of inlet pressure and air preheat temperature on the SVF distribution was separately investigated within a pressure range of 241–425 kPa and a temperature range of 292–500 K. The results show that soot production increases with the inlet pressure but generally decreases with the air preheat temperature. Qualitative analysis was provided to explain the above results of parametric studies. The LII experiments were also conducted under 3 designed conditions to evaluate soot emission under practical operations. Particularly, weak soot emission was detected at the outlet under the idle condition. Our experimental results provide a valuable benchmark for evaluating soot emission in the exhaust plume of this aero-engine combustor during practical operations.展开更多
Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow ch...Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow characteristics and performances of the generic hypersonic inlets by numerical simulation under the design conditions of a flight Mach number of 6 and an altitude of 26 km.The results show that the local shock interference patterns in the vicinity of the blunted cowl-lips have a substantial influence on the flow characteristics of the hypersonic inlets even though the blunting radius is very small,which contribute to a pronounced degradation of the inlet performance.The Equal Length blunting Manner(ELM)is the most optimal in that a nearly even reflection of the ramp shock produces an approximately straight and weak cowl reflection shock.The minimal total pressure loss,the lowest cowl drag,maximum mass-capture and the minimal aeroheating are achieved for the hypersonic inlet.For the other blunting manners,the ramp shock cannot reflect evenly and produces more curved cowl reflection shock.The Type V shock interference pattern occurs for the Cross Section Cutting blunting Manner(CSCM)and the strongest cowl reflection shock gives rise to the largest flow loss and drag.The cowl-lip blunted by the other two blunting manners is subjected to the shock interference pattern that transits with an increase in the blunting radius.Accordingly,the peak heat flux does not fall monotonously with the blunting radius increasing.Moreover,the cowl-lip surface suffers from severe aerothermal load when the shear layer or the supersonic jet impinges on the wall.展开更多
To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is prese...To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is presented.Moreover,a novel forebody design methodology which by rotating and assembling two waverider-based surfaces is firstly introduced in this paper.Some typical configurations are designed and their aerodynamic performances are evaluated by computational fluid dynamics.The results for forebodies analysis show that large volumetric efficiency,high lift-to-drag ratio,and uniformly distributed flowfield at the inlet cross section can be assured simultaneously.Furthermore,results of numerical simulation of four integrated configurations with various leading edge shapes,including three power-law curves and a cosine curve clearly show the advantage of high lift-to-drag ratio.Besides,the high pressure generated by the side wall of the airframe can be partly captured by the reasonably designed wings in the condition of small flight attack angle.Then the order of lift-to-drag ratio of four configurations at 0 degree flight attack angle is completely different from the condition of 4-degree flight attack angle.This result demonstrates that the curve shape of the leading edge is very important for the lift-to-drag ratio of the aircraft,and it should be further optimized under the cruising attack angle in future work.展开更多
This work focuses on streamline tracing techniques for designing hypersonic inlets, and two deficiencies were discovered.Firstly, constriction ratios of stream-traced inlets are unpredictable and uncontrollable, which...This work focuses on streamline tracing techniques for designing hypersonic inlets, and two deficiencies were discovered.Firstly, constriction ratios of stream-traced inlets are unpredictable and uncontrollable, which may affect the integration with airframes and combustors. Secondly, stream-traced inlets cannot exactly inherit properties from a basic flowfield through which they are traced. Then flow mechanisms underneath these phenomena were clarified. It was made clearly that properties of flow tubes captured by an inlet are what essentially determines constriction ratios as well as performances of inlets. Based on flow mechanisms, the method of calculating along streamlines(MCS) was proposed, which makes it possible to evaluate inlet performances directly. At last, optimization design methodologies were introduced to make inlet constriction ratios controllable,and simultaneously improve inlet performances as much as possible.展开更多
It is a major challenge for the airframe-inlet design of modern combat aircrafts,as the flow and electromagnetic wave propagation in the inlet of stealth aircraft are very complex.In this study,an aerodynamic/stealth ...It is a major challenge for the airframe-inlet design of modern combat aircrafts,as the flow and electromagnetic wave propagation in the inlet of stealth aircraft are very complex.In this study,an aerodynamic/stealth optimization design method for an S-duct inlet is proposed.The upwind scheme is introduced to the aerodynamic adjoint equation to resolve the shock wave and flow separation.The multilevel fast multipole algorithm(MLFMA)is utilized for the stealth adjoint equation.A dorsal S-duct inlet of flying wing layout is optimized to improve the aerodynamic and stealth characteristics.Both the aerodynamic and stealth characteristics of the inlet are effectively improved.Finally,the optimization results are analyzed,and it shows that the main contradiction between aerodynamic characteristics and stealth characteristics is the centerline and crosssectional area.The S-duct is smoothed,and the cross-sectional area is increased to improve the aerodynamic characteristics,while it is completely opposite for the stealth design.The radar cross section(RCS)is reduced by phase cancelation for low frequency conditions.The method is suitable for the aerodynamic/stealth design of the aircraft airframe-inlet system.展开更多
基金The National Key R&D Project of China under contract No.2017YFC1404201the USA North Pacific Research Board Project under contract No.1229the USA Bureau of Ocean Energy Management Awards under contract Nos M12PG00024(ACES)and M12PG00018(Arctic EIS)
文摘Estuarine processes in the arctic lagoons are among the least studied but important subjects, especially considering the rapid warming of arctic water which may change the length of ice-free period in the summer. In this paper, wind-driven exchange flows in the micro-tidal Elson Lagoon of northern Alaska with multiple inlets of contrasting widths and depths are studied with in situ observations, statistical analysis, numerical experiments, a regression model on the basis of dynamics, and remote sensing data. Water velocity profiles were obtained from a bottom deployed acoustic Doppler current profiler(ADCP) in the northwestern Eluitkak Pass connecting the Beaufort Sea to the Elson Lagoon during a 4.9 day ice-free period in the summer of 2013. The subtidal flow is found correlated with wind(R^2 value ～96%). Frequently occurring east, northeast and north winds from the arctic atmospheric high-and low-pressure systems push water from the Beaufort Sea into the lagoon through the wide inlets on the eastern side of the lagoon, resulting in an outward flow against the wind at the narrow northwestern inlet. The counter-wind flow is a result of an uneven wind forcing acting through the asymmetric inlets and depth,an effect of "torque" or vorticity. Under northwest wind, the exchange flow at the northwestern inlet reverses its direction, with inward flows through the upwind northwestern inlet and outward flows through the downwind eastern inlets. A regression model is established based on the momentum equations and Taylor series expansions. The model is used to predict flows in July and August of 2015 and July of 2017, supported by available Landsat satellite images. About 73%–80% of the time the flows at Eluitkak Pass are out of Elson Lagoon for the summer of 2015 and 2017. Numerical experiments are conducted to corroborate the findings and illustrate the effects under various wind conditions. A quasi-steady state balance between wind force and surface pressure gradient is confirmed.
基金The Foundation of China Ocean Mineral Resources R&D Association under contract No.DY135-E2-2-02the National Natural Science Foundation of China under contract Nos 9142820641976028 and 41806019。
文摘An inverse reduced-gravity model is used to simulate the deep South China Sea(SCS)circulation.A set of experiments are conducted using this model to study the influence of the Luzon overflow through the two inlets on the deep circulation in the northern SCS.Model results suggest that the relative contribution of these inlets largely depends on the magnitude of the input transport of the overflow,but the northern inlet is more efficient than the southern inlet in driving the deep circulation in the northern SCS.When all of the Luzon overflow occurs through the northern inlet the deep circulation in the northern SCS is enhanced.Conversely,when all of the Luzon overflow occurs through the southern inlet the circulation in the northern SCS is weakened.A Lagrangian trajectory model is also developed and applied to these cases.The Lagrangian results indicate that the location of the Luzon overflow likely has impacts upon the sediment transport into the northern SCS.
基金supported by the National Natural Science Foundation of China (Nos. 11702229, 11602207 and 91641103)
文摘In the design of a hypersonic inward-turning inlet by applying the traditional basic flowfield, a reflected shock-wave is formed in the isolator due to the continuous reflection of the cowlreflected shock wave in the basic flow-field, which interacts with the boundary layer to produce a considerable influence on the performance of the inlet. Here, a basic flow-field design method that can control the velocity direction at the throat section is developed, and numerical simulations are conducted to demonstrate the effectiveness of this method. The method presented in this paper can achieve the absorption of the reflected waves at the shoulder of the basic flow-field by adjusting the variation law of the center radius in the basic flow-field, and a smooth transition between the compression surface and the isolator can also be produced. The Mach number and total pressure recovery coefficient of the inlet designed according to this method are 3.00 and 0.657, respectively, at design point(the incoming flow Mach number Ma1= 6.0). The results show that with this method, the inlet can efficiently weaken both the reflection of the shock wave and the interaction between the boundary layer and the reflected shock waves, which improves the aerodynamic performance of the inlet.
基金financial support from the National Key Technologies R&D Program of China(2018YFF0216002)。
文摘The classification performance of model coal mill classifiers with different bottom incoming flow inlets was experimentally and numerically studied.The flow field adjacent to two neighboring impeller blades was measured using the particle image velocimetry technique.The results showed that the flow field adjacent to two neighboring blades with the swirling inlet was significantly different from that with the non-swirling inlet.With the swirling inlet,there was a vortex located between two neighboring blades,while with the nonswirling inlet,the vortex was attached to the blade tip.The vorticity of the vortex with the non-swirling inlet was much lower than that with the swirling inlet.The classifier with the non-swirling inlet demonstrated a larger cut size than that with the swirling inlet when the impeller was stationary(~0 r·min-1).As the impeller rotational speed increased,the cut size of the cases with non-swirling and swirling inlets both decreased,and the one with the non-swirling inlet decreased more dramatically.The values of the cut size of the two classifiers were close to each other at a high impeller rotational speed(≥120 r·min-1).The overall separation efficiency of the classifier with the non-swirling inlet was lower than that with the swirling inlet,and monotonically increased as the impeller rotational speed increased.With the swirling inlet,the overall separation efficiency first increased with the impeller rotational speed and then decreased when the rotational speed was above 120 r·min-1,and the variation trend of the separation efficiency was more moderate.As the initial particle concentration increased,the cut sizes of both swirling and non-swirling inlet cases decreased first and then barely changed.At a low initial particle concentration(b 0.04 kg·m-3),the classifier with the swirling inlet had a larger cut size than that with the non-swirling inlet.
基金This work is financially supported by the National Nature Science Fundation of China
文摘The relationship between P (spring tidal prism) and A (throat area below mean sea level) is statistically analysed in terms of 29 tidal inlets or bays along the Huanghai Sea (Yellow Sea) and Bohai Sea coasts. For 15 of these tidal inlets, the best regression equation is A(km2) = 0.845 />(km3)1.20. The analysis shows that C and n are little different from those in the P-A relationship for the inlets of the South China Sea and East China Sea coasts. It is noted that the relationship between P and A is unstable because of the difference in sediment abundance. The study shows that a united P-A relationship can be obtained for the tidal inlets of lagoon type and bay-drowned-valley type, not containing some half-circle shape bays which confront deep water. These half-circle bays do not belong to tidal inlets because they do not have enough sediment abundance and are fairly open.
基金supported by the ‘‘111" Project of China (No. B17037)
文摘In this work, a novel airframe/propulsion integration design method of the wing-body configuration for hypersonic cruise aircraft is proposed, where the configuration is integrated with inward-turning inlets. With the help of this method, the major design concern of balancing the aerodynamic performance against the requirements for efficient propulsion can be well addressed. A novel geometric parametrically modelling method based on a combination of patched class and shape transition（CST） and COONs surface is proposed to represent the configuration, especially a complex configuration with an irregular inlet lip shape. The modelling method enlarges the design space of components on the premise of guaranteeing the configuration integrity via special constraints imposed on the interface across adjacent surfaces. A basic flow inside a cone shaped by a dual-inflection-point generatrix is optimized to generate the inward-turning inlet with improvements of both compression efficiency and flow uniformity. The performance improvement mechanism of this basic flow is the compression velocity variation induced by the variation of the generatrix slope along the flow path. At the design point, numerical simulation results show that the lift-to-drag ratio of the configuration is as high as 5.2 and the inlet works well with a high level of compression efficiency and flow uniformity. The design result also has a good performance on off-design conditions. The achievement of all the design targets turns out that the integration design method proposed in this paper is efficient and practical.
文摘Aggregation is used to represent the real world in a model at an appropriate level of abstraction.We used the convection-diffusion equation to examine the implications of aggregation progressing from a three-dimensional(3D)spatial description to a model representing a system as a single box that exchanges sediment with the adjacent environment.We highlight how all models depend on some forms of parametric closure,which need to be chosen to suit the scale of aggregation adopted in the model.All such models are therefore aggregated and make use of some empirical relationships to deal with sub-scale processes.One such appropriately aggregated model,the model for the aggregated scale morphological interaction between tidal basin and adjacent coast(ASMITA),is examined in more detail and used to illustrate the insight that this level of aggregation can bring to a problem by considering how tidal inlets and estuaries are impacted by sea level rise.
文摘The French Atlantic coast seismicity is minor to moderate. Nevertheless, in western （north and central） part of France, the active tectonics related to the south Armorican and the Bay of Biscay context results sometimes in shallow earthquakes with magnitude above five （e.g., the Oleron seismic crisis, magnitude （local） = 5.2, 1972）. The Charente region is featured by semi-diurnal tides that reach about six meters in height during the high tide period. Inlets are the main features of the Atlantic margin geomorphology nearby the Charente. Minor tsunamis have been observed and reported in the past. Here, we present a tsunami modelling computed with the TELEMAC package that solves the non linear shallow water equations. This work helps to identify the role of the inlets that characterize the Charente＇s geomorphology on water wave＇s propagation. A tidal model is considered while the tsunami simulation is performed. The modelling results show that the Antioche, the Maumusson and the Pertuis inlets protect the Charente coast from destructive waves.
文摘Sandy inlets are in a dynamic equilibrium between wave-driven littoral drift acting to close them,and tidal flows keeping them open.Their beds are in a continual state of suspension and deposition,so their bathymetry and even location are always in flux.Even so,a nearly linear relationship between an inlet’s cross-sectional flow area and the inshore tidal prism is maintained-except when major wind and/or runoff events act to close or widen an inlet.Inlet location can be stabilized by jetties,but dredging may still be necessary to maintain a navigable channel.Armoring with rock large enough to resist erosion can protect an inlet bed or river mouth from excessive storm flow erosion.Armoring can also be used as a stratagem to close inlets.
基金support of the National Science and Technology Major Project of China(No.J2019-V-0005-0096)the National Key Research and Development Program of China(No.2020YFA0405700).
文摘The spatiotemporal distribution of soot concentration in aero-engine combustor is important for assessing its combustion performance.Here,we report experimental measurements of soot concentration in terms of Soot Volume Fraction(SVF)and its spatiotemporal distribution in a single-sector dual-swirl aero-engine combustor using Two-Color Laser-Induced Incandescence(2C-LII).It is shown that soot predominantly forms in the symmetrical vortices of the primary combustion zone,exhibiting a V-type distribution with higher concentration in the lower half of the zone than the upper half,with a small amount distributed in the secondary recirculation zone.Soot emissions at the combustor outlet are relatively low under three typical operating conditions by LII experiments,which is aligned with Smoke Number(SN)from gas analysis.The effect of inlet air temperature on SVF distribution and dynamics in the primary combustion zone is studied,which suggests that the SVF level in the primary combustion zone monotonically increases with the temperature.Meanwhile,the SVF distribution becomes more symmetrical as the inlet temperature increases,although the overall SVF level in the lower half of the zone is still higher.We also investigate the influence of the inlet air pressure on the SVF distribution at the combustor outlet.The soot concentration at the combustor outlet increases with inlet pressure,mainly distributed irregularly across both sides and the center.On both sides,the distribution is continuous,while the center exhibits dot-like and linear patterns.Numerical simulations correlated SVF distribution with the flow field in the primary combustion zone,qualitatively explaining the observed SVF distribution behavior.These results under various conditions can provide valuable insights for improving the performance of this specific combustor and designing high-temperature-rise combustors in the future.
基金funded by the National Natural Science Foundation of China(Nos.12025202,U20A2070,12172175)the National Science and Technology Major Project,China(No.J2019-Ⅱ-0014-0035)+2 种基金the Postdoctoral Fellowship Program of CPSF,China(No.GZB20230970)the Science Center for Gas Turbine Project,China(Nos.P2022-C-II-002-001,P2022-A-II-002-001)the Young Scientific and Technological Talents Project of Jiangsu Association for Science and Technology,China(No.TJ-2021-052)。
文摘This study aims to investigate the intricate dynamic characteristics of the high-speed duct during the over-under Turbine-Based Combined Cycle(TBCC)inlet mode transition process while operating in an off-design state under throttled conditions.A typical over-under TBCC inlet,designed for a working Mach number range of 0–6 with a transition Mach number of 3.5,is examined through experimental studies in a supersonic wind tunnel with a freestream Mach number of2.9.The investigation focuses on the complex oscillatory flow and unique hysteresis observed in the mode transition process of the high-speed duct under the mildly throttled condition,utilizing highspeed schlieren and dynamic pressure acquisition system.The findings reveal that the high-speed duct undergoes four distinct oscillation stages akin to those in a higher throttled state during the mode transition,albeit with smaller dominant frequency and energy.Moreover,an irregular alternating“big/little buzz”mode is observed in the early stage of the large oscillation stage.Notably,the mildly throttled state exhibits three intriguing hysteresis properties compared to the unthrottled and higher throttled states.Firstly,hysteresis is observed in the shock train motion stage in the duct before unstart,along with the corresponding inverse process.Subsequently,hysteresis is noted in the unstart and restart of the high-speed duct,with a smaller hysteresis interval than in the unthrottled state.Finally,the hysteresis characteristics of oscillation mode switching and the corresponding inverse process are explored.Based on the analysis,the first two hysteresis phenomena are associated with the formation and dissipation of the separation bubble.The significant adverse pressure gradient constrains the cross-sectional capacity of the channel,rendering the disappearance of the separation bubble more challenging.The hysteresis in oscillation mode switching is linked to not only the channel cross-sectional capacity but also the state of the incoming boundary layer.
基金co-supported by the Foundation of National Key Laboratory of Science and Technology on Aerodynamic Design and Research,China(No.614220121020114)the Key R&D Projects of Hunan Province,China(No.2023GK2022)。
文摘The design of wide-range high-efficiency aerodynamic configurations is one of the most important key technologies in the research of near-space hypersonic vehicles.A double-sided intake configuration with different inlets on the upper and lower surfaces is proposed to adapt to widerange flight.Firstly,the double-sided intake configuration’s design method and flight profile are delineated.Secondly,Computational Fluid Dynamics(CFD)numerical simulation based on multi-Graphics Processing Unit(GPU)parallel computing is adopted to evaluate the vehicle’s performance comprehensively,aiming to verify the feasibility of the proposed scheme.This evaluation encompasses a wide-range basic aerodynamic characteristics,inlet performance,and heat flux at critical locations.The results show that the inlets of the designed integration configuration can start up across Mach number 3.5 to 8.The vehicle possesses multi-point cruising capability by flipping the fuselage.Simultaneously,a 180°rotation of the fuselage can significantly decrease the heat accumulation on the lower surface of the vehicle,particularly at the inlet lip,further decreasing the temperature gradient across the vehicle structure.This study has some engineering value for the aerodynamic configuration design of wide-range vehicles.However,further study reveals that the flow phenomena at the intersection of two inlets are complex,posing potential adverse impacts on propulsion efficiency.Therefore,it is imperative to conduct additional research to delve into this matter comprehensively.
基金support of the National Natural Science Foundation of China(No.52322603)the Science Center for Gas Turbine Project of China(Nos.P2022-B-II-004-001 and P2023-B-II-001-001)+1 种基金the Fundamental Research Funds for the Central Universities,Chinathe Beijing Nova Program of China(Nos.20220484074 and 20230484479).
文摘The utilization of Inlet Guide Vane (IGV) plays a key factor in affecting the instability evolution. Existing literature mainly focuses on the effect of IGV on instability inception that occurs in the rotor region. However, with the emergence of compressor instability starting from the stator region, the mechanism of various instability inceptions that occurs in different blade rows due to the change of IGV angles should be further examined. In this study, experiments were focused on three types of instability inceptions observed previously in a 1.5-stage axial flow compressor. To analyze the conversion of stall evolutions, the compressor rotating speed was set to 17 160 r/min, at which both the blade loading in the stator hub region and rotor tip region were close to the critical value before final compressor stall. Meanwhile, the dynamic test points with high-response were placed to monitor the pressures both at the stator trailing edges and rotor tips. The results indicate that the variation of reaction determines the region where initial instability occurs. Indeed, negative pre-rotation of the inlet guide vane leads to high-reaction, initiating stall disturbance from the rotor region. Positive pre-rotation results in low-reaction, initiating stall disturbance from the stator region. Furthermore, the type of instability evolution is affected by the radial loading distribution under different IGV angles. Specifically, a spike-type inception occurs at the rotor blade tip with a large angle of attack at the rotor inlet (−2°, −4° and −6°). Meanwhile, the critical total pressure ratio at the rotor tip is 1.40 near stall. As the angle of attack decreases, the stator blade loading reaches its critical boundary, with a value of approximately 1.35. At this moment, if the rotor tip maintains high blade loading similar to the stator hub, the partial surge occurs (0° and +2°);otherwise, the hub instability occurs (+4° and +6°).
基金supported by the Na tional Natural Science Foundation of China(No.62373185)the National Key R&D Program of China(No.2023YFB3307100).
文摘To tackle the instability fault diagnosis challenges in wide-speed-range supersonic inlets,this study proposes an inlet fault decision fusion diagnosis algorithm based on attention mechanism feature fusion,achieving efficient diagnosis of instability faults across wide-speed regimes.First,considering the requirement for wall pressure data extraction in mathematical modeling of wide-speed-range inlets,a supersonic inlet reference model is established for computational fluid dynamics(CFD)simulations.Second,leveraging data-driven modeling techniques and support vector machine(SVM)algorithms,a high-precision mathematical model covering wide-speed domains and incorporating instability mechanisms is rapidly developed using CFD-derived inlet wall pressure data.Subsequently,an inlet fault decision fusion diagnosis method is proposed.Pressure features are fused via attention mechanisms,followed by Dempster-Shafer(D-S)evidence theory-based decision fusion,which integrates advantages of multiple intelligent algorithms to overcome the limitations of single-signal diagnosis methods(low accuracy and constrained optimization potential).The simulation results demonstrate the effectiveness of the data-driven wide-speed-range inlet model in achieving high precision and rapid convergence.In addition,the fusion diagnosis algorithm has been shown to attain over 95%accuracy in the detection of instability,indicating an improvement of more than 5%compared to the accuracy of other single fault diagnosis algorithms.This enhancement effectively eliminates the occurrence of missed or false diagnoses,while demonstrates robust performance under operational uncertainties.
基金supported by the National Natural Science Foundation of China(Nos.52306035 and 52325602)the Science Center for Gas Turbine Project,China(Nos.P2022-A-II-002-001 and P2022-C-II-003-001)+1 种基金the National Science and Technology Major Project,China(Nos.Y2022-II-0002-0005 and Y2022-II-0003-0006)the Key Laboratory of Pre-Research Management Centre,China(No.6142702200101)。
文摘An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(CT)on the stall margin recovery.An operating cycle is proposed based on the hysteresis effect of harmonic flap oscillation of airfoils and parallel compressor theory to explain the pressure characteristic of the fan under twin swirl inlets.Twin swirls are observed to reduce the stall margin of the fan,and the circumferential location where the spike is detected turns to the intersection area of the twin swirl.The IBC CT is proven to extend the stall margin of the fan for 12.7%–22.3%when subjected to inlet swirls with an efficiency loss of around 1%.The IBC CT helps to reduce the size of the operating cycle of the fan by redistributing the blade loading and adding the system damping to dissipate the perturbation energy.
基金supported by the National Key Research and Development Program of China(No.2020YFA0405700).
文摘Quantitative measurement of Soot Volume Fraction (SVF) is an essential prerequisite for controlling soot particle emissions from aero-engine combustors. As an in-situ and non-intrusive optical diagnostic technique, Laser-Induced Incandescence (LII) has been increasingly applied for soot concentration quantification in various combustion environments such as laminar flame, vehicle exhaust, internal combustion chamber as well as aero-engine combustor. In this work, we experimentally measured the spatial and temporal distribution of SVF using two-color LII technique at the outlet of a single-sector dual-swirl aero-engine model combustor. The effect of inlet pressure and air preheat temperature on the SVF distribution was separately investigated within a pressure range of 241–425 kPa and a temperature range of 292–500 K. The results show that soot production increases with the inlet pressure but generally decreases with the air preheat temperature. Qualitative analysis was provided to explain the above results of parametric studies. The LII experiments were also conducted under 3 designed conditions to evaluate soot emission under practical operations. Particularly, weak soot emission was detected at the outlet under the idle condition. Our experimental results provide a valuable benchmark for evaluating soot emission in the exhaust plume of this aero-engine combustor during practical operations.
基金supported by the National Natural Science Foundation of China(Grant Nos.90716014 and 91216115)
文摘Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow characteristics and performances of the generic hypersonic inlets by numerical simulation under the design conditions of a flight Mach number of 6 and an altitude of 26 km.The results show that the local shock interference patterns in the vicinity of the blunted cowl-lips have a substantial influence on the flow characteristics of the hypersonic inlets even though the blunting radius is very small,which contribute to a pronounced degradation of the inlet performance.The Equal Length blunting Manner(ELM)is the most optimal in that a nearly even reflection of the ramp shock produces an approximately straight and weak cowl reflection shock.The minimal total pressure loss,the lowest cowl drag,maximum mass-capture and the minimal aeroheating are achieved for the hypersonic inlet.For the other blunting manners,the ramp shock cannot reflect evenly and produces more curved cowl reflection shock.The Type V shock interference pattern occurs for the Cross Section Cutting blunting Manner(CSCM)and the strongest cowl reflection shock gives rise to the largest flow loss and drag.The cowl-lip blunted by the other two blunting manners is subjected to the shock interference pattern that transits with an increase in the blunting radius.Accordingly,the peak heat flux does not fall monotonously with the blunting radius increasing.Moreover,the cowl-lip surface suffers from severe aerothermal load when the shear layer or the supersonic jet impinges on the wall.
基金supported by the National Natural Science Foundation of China (Grant No. 90916013)the guidance and help from Academician Li Tian and peer reviewers are gratefully acknowledged
文摘To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is presented.Moreover,a novel forebody design methodology which by rotating and assembling two waverider-based surfaces is firstly introduced in this paper.Some typical configurations are designed and their aerodynamic performances are evaluated by computational fluid dynamics.The results for forebodies analysis show that large volumetric efficiency,high lift-to-drag ratio,and uniformly distributed flowfield at the inlet cross section can be assured simultaneously.Furthermore,results of numerical simulation of four integrated configurations with various leading edge shapes,including three power-law curves and a cosine curve clearly show the advantage of high lift-to-drag ratio.Besides,the high pressure generated by the side wall of the airframe can be partly captured by the reasonably designed wings in the condition of small flight attack angle.Then the order of lift-to-drag ratio of four configurations at 0 degree flight attack angle is completely different from the condition of 4-degree flight attack angle.This result demonstrates that the curve shape of the leading edge is very important for the lift-to-drag ratio of the aircraft,and it should be further optimized under the cruising attack angle in future work.
基金supported by the National Natural Science Foundation of China(Grant Nos.11572347,11872071)the China Scholarship Council(CSC)
文摘This work focuses on streamline tracing techniques for designing hypersonic inlets, and two deficiencies were discovered.Firstly, constriction ratios of stream-traced inlets are unpredictable and uncontrollable, which may affect the integration with airframes and combustors. Secondly, stream-traced inlets cannot exactly inherit properties from a basic flowfield through which they are traced. Then flow mechanisms underneath these phenomena were clarified. It was made clearly that properties of flow tubes captured by an inlet are what essentially determines constriction ratios as well as performances of inlets. Based on flow mechanisms, the method of calculating along streamlines(MCS) was proposed, which makes it possible to evaluate inlet performances directly. At last, optimization design methodologies were introduced to make inlet constriction ratios controllable,and simultaneously improve inlet performances as much as possible.
文摘It is a major challenge for the airframe-inlet design of modern combat aircrafts,as the flow and electromagnetic wave propagation in the inlet of stealth aircraft are very complex.In this study,an aerodynamic/stealth optimization design method for an S-duct inlet is proposed.The upwind scheme is introduced to the aerodynamic adjoint equation to resolve the shock wave and flow separation.The multilevel fast multipole algorithm(MLFMA)is utilized for the stealth adjoint equation.A dorsal S-duct inlet of flying wing layout is optimized to improve the aerodynamic and stealth characteristics.Both the aerodynamic and stealth characteristics of the inlet are effectively improved.Finally,the optimization results are analyzed,and it shows that the main contradiction between aerodynamic characteristics and stealth characteristics is the centerline and crosssectional area.The S-duct is smoothed,and the cross-sectional area is increased to improve the aerodynamic characteristics,while it is completely opposite for the stealth design.The radar cross section(RCS)is reduced by phase cancelation for low frequency conditions.The method is suitable for the aerodynamic/stealth design of the aircraft airframe-inlet system.
