This study investigates the performance of high-strength cable bolts under impact loading conditions representative of rock bursts in underground environments.Although widely used,the dynamic behaviour of these cable ...This study investigates the performance of high-strength cable bolts under impact loading conditions representative of rock bursts in underground environments.Although widely used,the dynamic behaviour of these cable bolts has received limited experimental attention,and their effectiveness in seismically active zones remains a subject of ongoing debate.To address this gap,a reverse pull-out test machine integrated with a drop hammer rig was employed.Tests were conducted on 70-t SUMO bulbed and non-bulbed cable bolts with encapsulation lengths of 300 and 450 mm,subjected to an impact energy of 14.52 k J.Results indicate that non-bulbed cables,despite showing lower initial peak loads(average 218 vs.328 k N for bulbed cables at 300 mm encapsulation),demonstrated superior energy absorption(average 11.26 vs.8.75 k J)and displacement capacity(average 48.40 vs.36.25 mm).Increasing the encapsulation length for bulbed cables led to a reduction in initial peak load but improved displacement and energy absorption.The dominant failure mechanism was debonding at the cable-grout interface,characterised by frictional sliding and cable rotation.These findings provide new insights into the energy dissipation mechanisms of cables and support the development of more resilient ground support systems for dynamically active conditions.展开更多
Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impac...Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impact of projectiles generated by the tornado,falling construction equipment,and also from accidental explosions during their construction and service lifespan.Impacts due to rock/boulder falls do occur on the structures located especially in hilly areas.Such loadings are not predictable but may cause severe damage to the slab/structure.It stimulates structural engineers and researchers to investigate and understand the dynamic response of RC structures under such impulsive loading.This research work first investigates the performance of 1000×1000×75 mm^(3)conventionally reinforced two-way spanning normal strength concrete slab with only tension reinforcement(0.88%)under the concentric impact load(1035 N)using the finite element method based computer code,ABAQUS/Explicit-v.6.15.The impact load is delivered to the centroid of the slab using a solid-steel cylindroconical impactor(drop weight)with a flat nose of diameter 40 mm,having a total mass of 105 kg released from a fixed height of 2500 mm.Two popular concrete constitutive models in ABAQUS namely;Holmquist-Johnson-Cook(HJC)and Concrete Damage Plasticity(CDP),with strain rate effects as per fib MODEL CODE 2010,are used to model the concrete material behavior to impact loading and to simulate the damage to the slab.The slab response using these two models is analyzed and compared with the impact test results.The strain rate effect on the reinforcing steel bars has been incorporated in the analysis using the Malvar and Crawford(1998)approach.A classical elastoplastic kinematic idealization is considered to model the steel impactor and support system.Results reveal that the HJC model gives a little overestimation of peak displacement,maximum acceleration,and damage of the slab while the predictions given by the CDP model are in reasonable agreement with the experimental test results/observations available in the open literature.Following the validation of the numerical model,analyses have been extended to further investigate the damage response of the slab under eccentric impact loadings.In addition to the concentric location(P1)of the impacting device,five locations on a quarter of the slab i.e.,two along the diagonal(P2&P3),the other two along the mid-span(P4&P5),and the last one(P6)between P3 and P5,covering the entire slab,are considered.Computational results have been discussed and compared,and the evaluation of the most damaging location(s)of the impact is investigated.It has been found that the most critical location of the impact is not the centroid of the slab but the eccentric one with the eccentricity of 1/6th of the span from the centroid along the mid-span section.展开更多
In rock drilling and blasting,the misfire of electronic detonators will not only affect the rock fragmentation result but also bring serious potential safety hazards to engineering construction.An accurate and compreh...In rock drilling and blasting,the misfire of electronic detonators will not only affect the rock fragmentation result but also bring serious potential safety hazards to engineering construction.An accurate and comprehensive understanding of the failure mechanisms of electronic detonators subjected to impact loading is of great significance to the reliability design and field safety use of electronic detonators.The spatial distribution characteristics and failure modes of misfired electronic detonators under different application scenarios are statistically analysed.The results show that under high impact loads,electronic detonators will experience failure phenomena such as rupture of the fuse head,fracture of the bridge wire,falling off of the solder joint,chip module damage and insufficient initiation energy after deformation.The lack of impact resistance is the primary cause of misfire of electronic detonators.Combined with the underwater impact resistance test and the impact load test in the adjacent blasthole on site,the formulas of the impact failure probability of the electronic detonator under different stress‒strength distribution curves are deduced.The test and evaluation method of the impact resistance of electronic detonators based on stress‒strength interference theory is proposed.Furthermore,the impact failure model of electronic detonators considering the strength degradation effect under repeated random loads is established.On this basis,the failure mechanism of electronic detonators under different application environments,such as open-pit blasting and underground blasting,is revealed,which provides scientific theory and methods for the reliability analysis,design and type selection of electronic detonators in rock drilling and blasting.展开更多
In this study,a coupled loading method combining three-dimensional static loading with graded cyclic impacts was developed to simulate the stress environment of the surrounding rock under impact ground pressure caused...In this study,a coupled loading method combining three-dimensional static loading with graded cyclic impacts was developed to simulate the stress environment of the surrounding rock under impact ground pressure caused by cyclic disturbances.The mechanical behavior and energy dissipation of coal under this loading method were studied using a split Hopkinson pressure bar(SHPB).The results showed that the pre-applied cyclic low-pressure impacts deteriorated the coal sample's resistance to external loads.Under both cyclic low-pressure impacts and single high-pressure impacts,the dynamic peak stress and secant modulus decreased with increasing impact cycles,exhibiting dynamic fatigue characteristics.The dynamic secant modulus of the sample decreased by 4.14%-6.67%after each impact.The dissipated energy for coal fragmentation samples increased with the number of impacts,averaging 28%under cyclic low-pressure impacts and 29%under single high-pressure impacts.The efficiency of dissipated energy for coal fragmentation initially increased and then decreased as the wave impedance ratio between the coal sample and the bar increased,reaching a maximum of 43.3%when the ratio was 0.06.Based on the defined damage variable,the damage to coal samples from high-pressure impacts was found to be 12 times greater than that under low-pressure conditions.The degree of coal fragmentation was positively correlated with the maximum damage increment.With increasing maximum damage increment,the failure mode of the coal sample evolved from tensile failure to tensile-compressive-shear composite failure.展开更多
In this paper,the isogeometric analysis(IGA)method is employed to analyze the oscillation characteristics of functionally graded triply periodic minimal surface(FG-TPMS)curved-doubly shells integrated with magneto-ele...In this paper,the isogeometric analysis(IGA)method is employed to analyze the oscillation characteristics of functionally graded triply periodic minimal surface(FG-TPMS)curved-doubly shells integrated with magneto-electric surface layers(referred to as"FG-TPMS-MEE curved-doubly shells")subjected to low-velocity impact loads.This study presents low-velocity impact load model based on a single springmass(S-M)approach.The FG-TPMS-MEE curved-doubly shells are covered with two magneto-electric surface layers,while the core layer consists of three types:I-graph and Wrapped Package-graph(IWP),Gyroid(G),and Primitive(P),with various graded functions.These types are notable for their exceptional stiffness-to-weight ratios,enabling a wide range of potential applications.The Maxwell equations and electromagnetic boundary conditions are applied to compute the change in electric potentials and magnetic potentials.The equilibrium equations of the shell are derived from a refined higher-order shear deformation theory(HSDT),and the transient responses of the FG-TPMS-MEE curveddoubly shells are subsequently determined using Newmark's direct integration method.These results have applications in structural vibration control and the analysis of structures subjected to impact or explosive loads.Furthermore,this study provides a theoretical prediction of the low-velocity impact load and magneto-electric-elastic effects on the free vibration and transient response of FG-TPMS-MEE curved-doubly shells.展开更多
Polymethacrylimide(PMI)foam has the highest specific stiffness and strength among polymer foams,with excellent radar-absorbing capabilities,which provide it with broad prospects in underwater ap-plications.To evaluate...Polymethacrylimide(PMI)foam has the highest specific stiffness and strength among polymer foams,with excellent radar-absorbing capabilities,which provide it with broad prospects in underwater ap-plications.To evaluate the impact resistance of PMI foam sandwich structures,the dynamic response and energy absorption characteristics of PMI foam sandwich structures with different core layers under various water impact loads were investigated using combined experimental and numerical methods.A fluid-structure interaction device with a diffusion angle was used for water impact testing of the PMI foam sandwich structures.The 3D-DIC technique was employed to process the deformation images of the sandwich-structure back panel captured by the high-speed cameras.Numerical simulations were performed to analyze the dynamic deformation process of the PMI foam core.The results indicated that the maximum deformation of the back panel exhibited a nonlinear relationship with the impulse.Below the critical impulse,the maximum deformation of the back panel plateaued,which was determined by the core density.Beyond the critical impulse,the rate of deformation increased with the impulse was governed by the core thickness.Compared with different sandwich panels,PMI foam sandwich struc-tures demonstrate significant advantages in terms of impact resistance under high-impulse conditions.展开更多
Carbon fiber-reinforced composites(CFRCs)have a wide range of applications in the aerospace,automotive,and energy sectors.A higher specific strength-to-weight ratio is desired in high-performance applications.The fail...Carbon fiber-reinforced composites(CFRCs)have a wide range of applications in the aerospace,automotive,and energy sectors.A higher specific strength-to-weight ratio is desired in high-performance applications.The failure mechanism of CFRCs involves multiscale phenomena,such as failure that can occur at the matrix,fibers,interface,layers,lamina,and laminates.When an impactor hits the CFRCs,the design involves analyzing each of these stages to prevent failure and optimize the properties of CFRCs under various loading conditions.A numerical model was employed to predict the fracture toughness of CFRCs with varying weight fractions and orientations.Finite Element Analysis(FEA)was conducted at the fiber level on a micrometer scale for the CFRCs against an impact loading.Epoxy composite samples at the coupon level were prepared using the hand layup technique with carbon fibers laid at three different angles,i.e.,longitudinal,transverse,and angular orientations.Samples with five different weight percentages of carbon fibers were prepared and investigated.An Izod impact tester was used to fracture the samples and characterize the energy absorption.The fractured surfaces were observed with a scanning electron microscope(SEM).The numerical and experimental results show that crack propagation is inhibited at higher loading fractions at an angular orientation by creating obstacles for the crack to propagate and arresting the dislocation motion.The fractography analysis through a scanning electron microscope exhibits how the angular orientations of the fibers are reoriented after fracture to prevent further crack propagation.展开更多
Sea ice exhibits complex mechanical properties,and no unified constitutive model currently exists.This study establishes an elastoplastic sea ice constitutive model based on non-ordinary state-based Peridynamics(PD)an...Sea ice exhibits complex mechanical properties,and no unified constitutive model currently exists.This study establishes an elastoplastic sea ice constitutive model based on non-ordinary state-based Peridynamics(PD)and the TsaiWu yield criterion,applying force state calculations to sea ice collisions while mitigating zero energy modes.A Fortran program implements the elastic-plastic constitutive equation of PD to simulate spherical ice-steel plate collisions.The program's accuracy in simulating sea ice collisions is validated through comparison with finite element results.Using the established model,this study simulates collisions between vertical structures and layer ice,analyzing the effects of impact velocity,vertical structure size,and critical elongation on sea ice load.The findings demonstrate positive correlations between collision force and impact velocity,vertical structure size,and critical elongation.At high velocities,impact significantly affects collision force,primarily following a quadratic function,while vertical structure effects exhibit a linear relationship.展开更多
To better design and analyze concrete structures, the mechanical properties of concrete subjected to impact loadings are investigated. Concrete is considered to be a two-phase composite made up of micro-cracks and sol...To better design and analyze concrete structures, the mechanical properties of concrete subjected to impact loadings are investigated. Concrete is considered to be a two-phase composite made up of micro-cracks and solid parts which consist of coarse aggregate particles and a cement mortar matrix. The cement mortar matrix is assumed to be elastic, homogeneous and isotropic. Based on the Moil-Tanaka concept of average stress and the Eshelby equivalent inclusion theory, a dynamic constitutive model is developed to simulate the impact responses of concrete. The impact compression experiments of concrete and cement mortar are also carried out. Experimental results show that concrete and cement mortar are rate-dependent. Under the same impact velocity, the load-carrying capacity of concrete is higher than that of cement mortar. Whereas, the maximum strain of concrete is lower than that of cement mortar. Regardless of whether it is concrete or cement mortar, with the increase in the impact velocity, the fragment size of specimens after experiment decreases.展开更多
In this paper, the boundary value problem (BVP) of 3 D transient eddy current field in the end region in the case that the generator is affected by impact load is specified. Besides, ways to implement discrete method...In this paper, the boundary value problem (BVP) of 3 D transient eddy current field in the end region in the case that the generator is affected by impact load is specified. Besides, ways to implement discrete methods in both time domain and space domain during the solution of the problem are investigated. The Crank Nicolson scheme is utilized to attain the iterative format of time differential, after taking factors that can ensure both computation precision and stability into consideration. In this paper, the magnetic distribution in the end region of a turbogenerator in the case that the generator is affected by impact load is specified. As a result, it provides foundation for further study of electromagnetic force and electromagnetic vibration in the end region of the turbogenerator.展开更多
On the basis of the study of transient eddy current field in the end region of turbogenerator and electromagnetic force of end region winding, this paper analyzes the electromagnetic vibration of the turbogenerator r...On the basis of the study of transient eddy current field in the end region of turbogenerator and electromagnetic force of end region winding, this paper analyzes the electromagnetic vibration of the turbogenerator roundly. A 320 MW turbogenerator is taken as an example to specify the electromagnetic force of end region winding and therefore the vibration in the case that the generator is affected by impact load. Some conclusions are drawn on the basis of the specification. Vibration of windings under imaginary faults is simulated, so that the vibration law of the end winding of turbogenerator can be studied further. On the basis of this, the countermeasure against winding vibration can be advanced.展开更多
Based on the split hopkinson pressure bar(SHPB)tests results,the cubic specimens have been numerically modeled in this paper to investigate the impact of key factors,such as the rise time,duration,and incident pulse s...Based on the split hopkinson pressure bar(SHPB)tests results,the cubic specimens have been numerically modeled in this paper to investigate the impact of key factors,such as the rise time,duration,and incident pulse shape,on achieving stress uniformity.After analysis,the paper provides actionable methods aimed at optimizing the conditions for stress uniformity within the cubic specimen.Finally,the lateral inertia effect of cubic specimen has been scrutinized to address the existing gap in this academic area.展开更多
Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic ...Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic mechanical properties. However, cement-iron ore tailings foam composite(CIFC), a sustainable material utilizing iron ore tailings to partially replace cement, has not been investigated under dynamic loading. This study investigates the dynamic compressive behavior of CIFC with 1%–2.5% PPF content and 3–12 mm PPF lengths under various strain rates. The microstructural characteristics were analyzed prior to dynamic testing. X-ray diffraction(XRD) identified crystalline phases including CaCO_(3)Fe_(2)O_(3), SiO, C-S-H gel, and ettringite. Scanning electron microscopy(SEM) observations demonstrated that appropriate PPF_(2) parameters(e.g., C2L9, a CIFC specimen containing 2% PPF with 9 mm length) enhance fiber-matrix bonding and minimize interconnected pores and microcracks, revealing pronounced fiber bridging effects. Split Hopkinson pressure bar(SHPB) tests were then conducted at strain rates of 120–250 s^(-1), showing that the dynamic properties of CIFC were highly dependent on both strain rates and PPF parameters. Compared to other specimens, C2L9 exhibited a more intact failure pattern with superior compressive strength and energy dissipation capacity, despite showing reduced dynamic increase factor(DIF) and normalized energy dissipation(NED) values. These findings provide practical guidance for applying CIFC with varying PPF parameters in impact-resistant structural designs.展开更多
The split-Hopkinson pressure bar(SHPB)and digital image correlation(DIC)techniques are combined to analyze the dynamic compressive failure process of coal samples,and the box fractal dimension is used to quantitativel...The split-Hopkinson pressure bar(SHPB)and digital image correlation(DIC)techniques are combined to analyze the dynamic compressive failure process of coal samples,and the box fractal dimension is used to quantitatively analyze the dynamic changes in the coal sample cracks under impact load conditions with different loading rates.The experimental results show that the fractal dimension can quantitatively describe the evolution process of coal fractures under dynamic load.During the dynamic compression process,the evolution of the coal sample cracks presents distinct stages.In the crack propagation stage,the fractal dimension increases rapidly with the progress of loading,and in the crack widening stage,the fractal dimension increases slowly with the progress of loading.The initiation of the crack propagation phase of the coal samples gradually occurs more quickly with increasing loading rate;the initial cracks appear earlier.At the same loading time point,when the loading rate is greater,the fractal dimension of the cracks observed in the coal sample is greater.展开更多
Cemented tailings backfill(CTB)structures are important components of underground mine stopes.It is important to investigate the characteristics and dynamic behavior of CTB materials because they are susceptible to di...Cemented tailings backfill(CTB)structures are important components of underground mine stopes.It is important to investigate the characteristics and dynamic behavior of CTB materials because they are susceptible to disturbance by dynamic loading,such as excavation and blasting.In this study,the authors present the results of a series of Split-Hopkinson pressure bar(SHPB)single and cyclic impact loading tests on CTB specimens to investigate the long-term dynamic mechanical properties of CTB.The stress-strain relationship,dynamic strength,and dynamic failure characteristics of CTB specimens are analyzed and discussed to provide valuable conclusions that will improve our knowledge of CTB long-term mechanical behavior and characteristics.For instance,the dynamic peak stress under cyclic impact loading is approximately twice that under single impact loading,and the CTB specimens are less prone to fracture when cyclically loaded.These findings and conclusions can provide a new set of references for the stability analysis of CTB materials and help guide mine designers in reducing the amount of binding agents and the associated mining cost.展开更多
We studied the dynamic fracture mechanical behavior of rock under different impact rates. The fracture experiment was a three-point bending beam subjected to different impact loads monitored using the reflected causti...We studied the dynamic fracture mechanical behavior of rock under different impact rates. The fracture experiment was a three-point bending beam subjected to different impact loads monitored using the reflected caustics method. The mechanical parameters for fracture of the three-poim bending beam specimen under impact load are analyzed. The mechanism of crack propagation is discussed. Experimental results show that the dynamic stress intensity factor increases before crack initiation. When the dynamic stress intensity factor reaches its maximum value the crack starts to develop. After crack initiation the dynamic stress intensity factor decreases rapidly and oscillates. As the impact rate increases the cracks initiate earlier, the maximum value of crack growth velocity becomes smaller and the values of dynamic stress intensity factor also vary less during crack propagation. The results provide a theoretical basis for the study of rock dynamic fracture.展开更多
Crack dynamic propagation and arrest behaviors have received extensive attention over the years.However,there still remain many questions,e.g.under what conditions will a running crack come to arrest?In this paper,dro...Crack dynamic propagation and arrest behaviors have received extensive attention over the years.However,there still remain many questions,e.g.under what conditions will a running crack come to arrest?In this paper,drop weight impact(DWI)tests were conducted to investigate crack arrest mechanism using single cleavage triangle(SCT)rock specimens.Green sandstone was selected to prepare the SCT specimens.Dynamic stress intensity factors(DSIFs)were calculated by ABAQUS code,and the critical DSIFs were determined by crack propagation speeds and fracture time measured by crack propagation gauges(CPGs).The test results show that the critical DSIF at propagation decreases with crack propagation speed.Numerical simulation for SCT specimens under different loading waves was performed using AUTODYN code.The reflected compressive wave from the incident and transmitted plates can induce crack arrests during propagation,and the number of arrest times increases with the wave length.In order to eliminate the effect of the incident and transmitted plates,models consisting of only one SCT specimen without incident and transmitted plates were established,and the same trapezoid-shaped loading wave was applied to the SCT specimen.The results show that for the SCT specimen with transmitted boundary(analogous to an infinite plate),the trapezoid-shaped loading wave cannot induce crack arrest anymore.The numerical results can well describe the occurrence of crack arrest in the experiments.展开更多
The transient response of an unlimited cylindrical cavity buried in the infinite elastic soil subjected to an anti-plane impact load along the cavern axis direction was studied.Using Laplace transform combining with c...The transient response of an unlimited cylindrical cavity buried in the infinite elastic soil subjected to an anti-plane impact load along the cavern axis direction was studied.Using Laplace transform combining with contour integral of the Laplace inverse transform specifically,the general analytical expressions of the soil displacement and stress are obtained in the time domain,respectively.And the numerical solutions of the problem computed by analytical expressions are presented.In the time domain,the dynamic responses of the infinite elastic soil are analyzed,and the calculation results are compared with those from numerical inversion proposed by Durbin and the static results.One observes good agreement between analytical and numerical inversion results,lending the further support to the method presented.Finally,some valuable shear wave propagation laws are gained: the displacement of the soil remains zero before the wave arrival,and after the shear wave arrival,the stress and the displacement at this point increase abruptly,then reduce and tend to the static value gradually at last.The wave attenuates along the radial,therefore the farther the wave is from the source,the smaller the stress and the displacement are,and the stress and the displacement are just functions of the radial distance from the axis.展开更多
Impact-induced damage to jointed rock masses has important consequences in various mining and civil engineering applications. This paper reports a numerical investigation to address the responses of jointed rock masse...Impact-induced damage to jointed rock masses has important consequences in various mining and civil engineering applications. This paper reports a numerical investigation to address the responses of jointed rock masses subjected to impact loading. It also focuses on the static and dynamic properties of an intact rock derived from a series of laboratory tests on meta-sandstone samples from a quarry in Nova Scotia, Canada. A distinct element code(PFC2D) was used to generate a bonded particle model(BPM) to simulate both the static and dynamic properties of the intact rock. The calibrated BPM was then used to construct large-scale jointed rock mass samples by incorporating discrete joint networks of multiple joint intensities into the intact rock matrix represented by the BPM. Finally, the impact-induced damage inflicted by a rigid projectile particle on the jointed rock mass samples was determined through the use of the numerical model. The simulation results show that joints play an important role in the impactinduced rock mass damage where higher joint intensity results in more damage to the rock mass. This is mainly attributed to variations of stress wave propagation in jointed rock masses as compared to intact rock devoid of joints.展开更多
Split Hopkinson pressure bar(SHPB)tests were conducted on pre-rolled AZ31 magnesium alloy at 150–350℃ with strain rates of 2150s-1,3430s^(-1) and 4160s-1.The mechanical response,microstructural evolution and accommo...Split Hopkinson pressure bar(SHPB)tests were conducted on pre-rolled AZ31 magnesium alloy at 150–350℃ with strain rates of 2150s-1,3430s^(-1) and 4160s-1.The mechanical response,microstructural evolution and accommodation mechanism of the pre-rolled AZ31 magnesium alloy under high-speed impact loading were investigated.The twin and shear band are prevailing at low temperature,and the coexistence of twins and recrystallized grains is the dominant microstructure at medium temperature,while at high temperature,dynamic recrystallization(DRX)is almost complete.The increment of temperature reduces the critical condition difference between twinning and DRX,and the recrystallized temperature decreases with increasing strain rate.The mechanical response is related to the competition among the shear band strengthen,the twin strengthen and the fine grain strengthen and determined by the prevailing grain structure.The fine grain strengthen could compensate soften caused by the temperature increase and the reduction of twin and shear band.During high-speed deformation,different twin variants,introduced by pre-rolling,induce different deformation mechanism to accommodate plastic deformation and are in favor for non-basal slip.At low temperature,the high-speed deformation is achieved by twinning,dislocation slip and the following deformation shear band at different deformation stages.At high temperature,the high-speed deformation is realized by twinning and dislocation slip of early deformation stage,transition shear band of medium deformation stage and DRX of final deformation stage.展开更多
文摘This study investigates the performance of high-strength cable bolts under impact loading conditions representative of rock bursts in underground environments.Although widely used,the dynamic behaviour of these cable bolts has received limited experimental attention,and their effectiveness in seismically active zones remains a subject of ongoing debate.To address this gap,a reverse pull-out test machine integrated with a drop hammer rig was employed.Tests were conducted on 70-t SUMO bulbed and non-bulbed cable bolts with encapsulation lengths of 300 and 450 mm,subjected to an impact energy of 14.52 k J.Results indicate that non-bulbed cables,despite showing lower initial peak loads(average 218 vs.328 k N for bulbed cables at 300 mm encapsulation),demonstrated superior energy absorption(average 11.26 vs.8.75 k J)and displacement capacity(average 48.40 vs.36.25 mm).Increasing the encapsulation length for bulbed cables led to a reduction in initial peak load but improved displacement and energy absorption.The dominant failure mechanism was debonding at the cable-grout interface,characterised by frictional sliding and cable rotation.These findings provide new insights into the energy dissipation mechanisms of cables and support the development of more resilient ground support systems for dynamically active conditions.
文摘Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impact of projectiles generated by the tornado,falling construction equipment,and also from accidental explosions during their construction and service lifespan.Impacts due to rock/boulder falls do occur on the structures located especially in hilly areas.Such loadings are not predictable but may cause severe damage to the slab/structure.It stimulates structural engineers and researchers to investigate and understand the dynamic response of RC structures under such impulsive loading.This research work first investigates the performance of 1000×1000×75 mm^(3)conventionally reinforced two-way spanning normal strength concrete slab with only tension reinforcement(0.88%)under the concentric impact load(1035 N)using the finite element method based computer code,ABAQUS/Explicit-v.6.15.The impact load is delivered to the centroid of the slab using a solid-steel cylindroconical impactor(drop weight)with a flat nose of diameter 40 mm,having a total mass of 105 kg released from a fixed height of 2500 mm.Two popular concrete constitutive models in ABAQUS namely;Holmquist-Johnson-Cook(HJC)and Concrete Damage Plasticity(CDP),with strain rate effects as per fib MODEL CODE 2010,are used to model the concrete material behavior to impact loading and to simulate the damage to the slab.The slab response using these two models is analyzed and compared with the impact test results.The strain rate effect on the reinforcing steel bars has been incorporated in the analysis using the Malvar and Crawford(1998)approach.A classical elastoplastic kinematic idealization is considered to model the steel impactor and support system.Results reveal that the HJC model gives a little overestimation of peak displacement,maximum acceleration,and damage of the slab while the predictions given by the CDP model are in reasonable agreement with the experimental test results/observations available in the open literature.Following the validation of the numerical model,analyses have been extended to further investigate the damage response of the slab under eccentric impact loadings.In addition to the concentric location(P1)of the impacting device,five locations on a quarter of the slab i.e.,two along the diagonal(P2&P3),the other two along the mid-span(P4&P5),and the last one(P6)between P3 and P5,covering the entire slab,are considered.Computational results have been discussed and compared,and the evaluation of the most damaging location(s)of the impact is investigated.It has been found that the most critical location of the impact is not the centroid of the slab but the eccentric one with the eccentricity of 1/6th of the span from the centroid along the mid-span section.
基金supported by the Chongqing Youth Talent Support Program(Cstc2022ycjh-bgzxm0079)the Chinese National Natural Science Foundation(52379128,51979152)+2 种基金Science Fund for Distinguished Young Scholars of Hubei Proivnce(2023AFA048)Educational Commission of Hubei Province of China(T2020005)the Young Top-notch Talent Cultivation Program of Hubei Province.
文摘In rock drilling and blasting,the misfire of electronic detonators will not only affect the rock fragmentation result but also bring serious potential safety hazards to engineering construction.An accurate and comprehensive understanding of the failure mechanisms of electronic detonators subjected to impact loading is of great significance to the reliability design and field safety use of electronic detonators.The spatial distribution characteristics and failure modes of misfired electronic detonators under different application scenarios are statistically analysed.The results show that under high impact loads,electronic detonators will experience failure phenomena such as rupture of the fuse head,fracture of the bridge wire,falling off of the solder joint,chip module damage and insufficient initiation energy after deformation.The lack of impact resistance is the primary cause of misfire of electronic detonators.Combined with the underwater impact resistance test and the impact load test in the adjacent blasthole on site,the formulas of the impact failure probability of the electronic detonator under different stress‒strength distribution curves are deduced.The test and evaluation method of the impact resistance of electronic detonators based on stress‒strength interference theory is proposed.Furthermore,the impact failure model of electronic detonators considering the strength degradation effect under repeated random loads is established.On this basis,the failure mechanism of electronic detonators under different application environments,such as open-pit blasting and underground blasting,is revealed,which provides scientific theory and methods for the reliability analysis,design and type selection of electronic detonators in rock drilling and blasting.
基金supported by the Youth Fund of the CCTEG Coal Mining Research Institute(Grant No.KCYJY-2023-QN-01)the National Natural Science Foundation of China(Grant No.52174080)the Science Foundation of Tiandi Technology Co.,Ltd.(Grant No.2022-2-TD-ZD016).
文摘In this study,a coupled loading method combining three-dimensional static loading with graded cyclic impacts was developed to simulate the stress environment of the surrounding rock under impact ground pressure caused by cyclic disturbances.The mechanical behavior and energy dissipation of coal under this loading method were studied using a split Hopkinson pressure bar(SHPB).The results showed that the pre-applied cyclic low-pressure impacts deteriorated the coal sample's resistance to external loads.Under both cyclic low-pressure impacts and single high-pressure impacts,the dynamic peak stress and secant modulus decreased with increasing impact cycles,exhibiting dynamic fatigue characteristics.The dynamic secant modulus of the sample decreased by 4.14%-6.67%after each impact.The dissipated energy for coal fragmentation samples increased with the number of impacts,averaging 28%under cyclic low-pressure impacts and 29%under single high-pressure impacts.The efficiency of dissipated energy for coal fragmentation initially increased and then decreased as the wave impedance ratio between the coal sample and the bar increased,reaching a maximum of 43.3%when the ratio was 0.06.Based on the defined damage variable,the damage to coal samples from high-pressure impacts was found to be 12 times greater than that under low-pressure conditions.The degree of coal fragmentation was positively correlated with the maximum damage increment.With increasing maximum damage increment,the failure mode of the coal sample evolved from tensile failure to tensile-compressive-shear composite failure.
文摘In this paper,the isogeometric analysis(IGA)method is employed to analyze the oscillation characteristics of functionally graded triply periodic minimal surface(FG-TPMS)curved-doubly shells integrated with magneto-electric surface layers(referred to as"FG-TPMS-MEE curved-doubly shells")subjected to low-velocity impact loads.This study presents low-velocity impact load model based on a single springmass(S-M)approach.The FG-TPMS-MEE curved-doubly shells are covered with two magneto-electric surface layers,while the core layer consists of three types:I-graph and Wrapped Package-graph(IWP),Gyroid(G),and Primitive(P),with various graded functions.These types are notable for their exceptional stiffness-to-weight ratios,enabling a wide range of potential applications.The Maxwell equations and electromagnetic boundary conditions are applied to compute the change in electric potentials and magnetic potentials.The equilibrium equations of the shell are derived from a refined higher-order shear deformation theory(HSDT),and the transient responses of the FG-TPMS-MEE curveddoubly shells are subsequently determined using Newmark's direct integration method.These results have applications in structural vibration control and the analysis of structures subjected to impact or explosive loads.Furthermore,this study provides a theoretical prediction of the low-velocity impact load and magneto-electric-elastic effects on the free vibration and transient response of FG-TPMS-MEE curved-doubly shells.
文摘Polymethacrylimide(PMI)foam has the highest specific stiffness and strength among polymer foams,with excellent radar-absorbing capabilities,which provide it with broad prospects in underwater ap-plications.To evaluate the impact resistance of PMI foam sandwich structures,the dynamic response and energy absorption characteristics of PMI foam sandwich structures with different core layers under various water impact loads were investigated using combined experimental and numerical methods.A fluid-structure interaction device with a diffusion angle was used for water impact testing of the PMI foam sandwich structures.The 3D-DIC technique was employed to process the deformation images of the sandwich-structure back panel captured by the high-speed cameras.Numerical simulations were performed to analyze the dynamic deformation process of the PMI foam core.The results indicated that the maximum deformation of the back panel exhibited a nonlinear relationship with the impulse.Below the critical impulse,the maximum deformation of the back panel plateaued,which was determined by the core density.Beyond the critical impulse,the rate of deformation increased with the impulse was governed by the core thickness.Compared with different sandwich panels,PMI foam sandwich struc-tures demonstrate significant advantages in terms of impact resistance under high-impulse conditions.
基金supported by the University of Texas(UT)system STARs grant,Semester Undergraduate Research Experience(SURE)program at the College of Engineering at the University of Texas Permian Basin(UTPB)EM-STEP(Engineering Minority Student Engagement Project)at UTPB College of Engineering,funded by Department of Education.
文摘Carbon fiber-reinforced composites(CFRCs)have a wide range of applications in the aerospace,automotive,and energy sectors.A higher specific strength-to-weight ratio is desired in high-performance applications.The failure mechanism of CFRCs involves multiscale phenomena,such as failure that can occur at the matrix,fibers,interface,layers,lamina,and laminates.When an impactor hits the CFRCs,the design involves analyzing each of these stages to prevent failure and optimize the properties of CFRCs under various loading conditions.A numerical model was employed to predict the fracture toughness of CFRCs with varying weight fractions and orientations.Finite Element Analysis(FEA)was conducted at the fiber level on a micrometer scale for the CFRCs against an impact loading.Epoxy composite samples at the coupon level were prepared using the hand layup technique with carbon fibers laid at three different angles,i.e.,longitudinal,transverse,and angular orientations.Samples with five different weight percentages of carbon fibers were prepared and investigated.An Izod impact tester was used to fracture the samples and characterize the energy absorption.The fractured surfaces were observed with a scanning electron microscope(SEM).The numerical and experimental results show that crack propagation is inhibited at higher loading fractions at an angular orientation by creating obstacles for the crack to propagate and arresting the dislocation motion.The fractography analysis through a scanning electron microscope exhibits how the angular orientations of the fibers are reoriented after fracture to prevent further crack propagation.
基金financially supported by the Aeronautical Science Foundation of China(Grant No.023M031077001)Shandong Provincial Natural Science Foundation(Grant No.ZR2022QE092)the Open Fund Project of Key Laboratory of Ocean Observation Technology,MNR(Grant No.2022klootA03)。
文摘Sea ice exhibits complex mechanical properties,and no unified constitutive model currently exists.This study establishes an elastoplastic sea ice constitutive model based on non-ordinary state-based Peridynamics(PD)and the TsaiWu yield criterion,applying force state calculations to sea ice collisions while mitigating zero energy modes.A Fortran program implements the elastic-plastic constitutive equation of PD to simulate spherical ice-steel plate collisions.The program's accuracy in simulating sea ice collisions is validated through comparison with finite element results.Using the established model,this study simulates collisions between vertical structures and layer ice,analyzing the effects of impact velocity,vertical structure size,and critical elongation on sea ice load.The findings demonstrate positive correlations between collision force and impact velocity,vertical structure size,and critical elongation.At high velocities,impact significantly affects collision force,primarily following a quadratic function,while vertical structure effects exhibit a linear relationship.
基金The National Natural Science Foundation of China(No. 11162015)the Natural Science Foundation of Ningxia Hui Autonomous Region (No. NZ1106)
文摘To better design and analyze concrete structures, the mechanical properties of concrete subjected to impact loadings are investigated. Concrete is considered to be a two-phase composite made up of micro-cracks and solid parts which consist of coarse aggregate particles and a cement mortar matrix. The cement mortar matrix is assumed to be elastic, homogeneous and isotropic. Based on the Moil-Tanaka concept of average stress and the Eshelby equivalent inclusion theory, a dynamic constitutive model is developed to simulate the impact responses of concrete. The impact compression experiments of concrete and cement mortar are also carried out. Experimental results show that concrete and cement mortar are rate-dependent. Under the same impact velocity, the load-carrying capacity of concrete is higher than that of cement mortar. Whereas, the maximum strain of concrete is lower than that of cement mortar. Regardless of whether it is concrete or cement mortar, with the increase in the impact velocity, the fragment size of specimens after experiment decreases.
文摘In this paper, the boundary value problem (BVP) of 3 D transient eddy current field in the end region in the case that the generator is affected by impact load is specified. Besides, ways to implement discrete methods in both time domain and space domain during the solution of the problem are investigated. The Crank Nicolson scheme is utilized to attain the iterative format of time differential, after taking factors that can ensure both computation precision and stability into consideration. In this paper, the magnetic distribution in the end region of a turbogenerator in the case that the generator is affected by impact load is specified. As a result, it provides foundation for further study of electromagnetic force and electromagnetic vibration in the end region of the turbogenerator.
文摘On the basis of the study of transient eddy current field in the end region of turbogenerator and electromagnetic force of end region winding, this paper analyzes the electromagnetic vibration of the turbogenerator roundly. A 320 MW turbogenerator is taken as an example to specify the electromagnetic force of end region winding and therefore the vibration in the case that the generator is affected by impact load. Some conclusions are drawn on the basis of the specification. Vibration of windings under imaginary faults is simulated, so that the vibration law of the end winding of turbogenerator can be studied further. On the basis of this, the countermeasure against winding vibration can be advanced.
基金Funded by the National Natural Science Foundation of China(Nos.52278518 and 51938011)the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(No.24KJB560021)。
文摘Based on the split hopkinson pressure bar(SHPB)tests results,the cubic specimens have been numerically modeled in this paper to investigate the impact of key factors,such as the rise time,duration,and incident pulse shape,on achieving stress uniformity.After analysis,the paper provides actionable methods aimed at optimizing the conditions for stress uniformity within the cubic specimen.Finally,the lateral inertia effect of cubic specimen has been scrutinized to address the existing gap in this academic area.
基金supported by the National Science Foundation for Excellent Young Scholars of China (Grant No.52422809)the National Natural Science Foundation of China (Grant No.52208491)。
文摘Polypropylene fibers(PPFs) have been widely used in composite materials due to their sound crack resistance and toughness. In cement-based composites, the incorporation of PPFs can significantly improve their dynamic mechanical properties. However, cement-iron ore tailings foam composite(CIFC), a sustainable material utilizing iron ore tailings to partially replace cement, has not been investigated under dynamic loading. This study investigates the dynamic compressive behavior of CIFC with 1%–2.5% PPF content and 3–12 mm PPF lengths under various strain rates. The microstructural characteristics were analyzed prior to dynamic testing. X-ray diffraction(XRD) identified crystalline phases including CaCO_(3)Fe_(2)O_(3), SiO, C-S-H gel, and ettringite. Scanning electron microscopy(SEM) observations demonstrated that appropriate PPF_(2) parameters(e.g., C2L9, a CIFC specimen containing 2% PPF with 9 mm length) enhance fiber-matrix bonding and minimize interconnected pores and microcracks, revealing pronounced fiber bridging effects. Split Hopkinson pressure bar(SHPB) tests were then conducted at strain rates of 120–250 s^(-1), showing that the dynamic properties of CIFC were highly dependent on both strain rates and PPF parameters. Compared to other specimens, C2L9 exhibited a more intact failure pattern with superior compressive strength and energy dissipation capacity, despite showing reduced dynamic increase factor(DIF) and normalized energy dissipation(NED) values. These findings provide practical guidance for applying CIFC with varying PPF parameters in impact-resistant structural designs.
基金Projects(51822403,51827901)supported by the National Natural Science Foundation of ChinaProject(2019ZT08G315)supported by the Department of Science and Technology of Guangdong Province,China。
文摘The split-Hopkinson pressure bar(SHPB)and digital image correlation(DIC)techniques are combined to analyze the dynamic compressive failure process of coal samples,and the box fractal dimension is used to quantitatively analyze the dynamic changes in the coal sample cracks under impact load conditions with different loading rates.The experimental results show that the fractal dimension can quantitatively describe the evolution process of coal fractures under dynamic load.During the dynamic compression process,the evolution of the coal sample cracks presents distinct stages.In the crack propagation stage,the fractal dimension increases rapidly with the progress of loading,and in the crack widening stage,the fractal dimension increases slowly with the progress of loading.The initiation of the crack propagation phase of the coal samples gradually occurs more quickly with increasing loading rate;the initial cracks appear earlier.At the same loading time point,when the loading rate is greater,the fractal dimension of the cracks observed in the coal sample is greater.
基金financially supported by the National Key R&D Program of China (No. 2017YFC0602900)the Fundamental Research Funds for the Central Universities (No. FRF-TP-17-029A2)the Open Fund of Key Laboratory of High-Efficient Mining and Safety of Metal Mines (Ministry of Education of China, No. ustbmslab201803)
文摘Cemented tailings backfill(CTB)structures are important components of underground mine stopes.It is important to investigate the characteristics and dynamic behavior of CTB materials because they are susceptible to disturbance by dynamic loading,such as excavation and blasting.In this study,the authors present the results of a series of Split-Hopkinson pressure bar(SHPB)single and cyclic impact loading tests on CTB specimens to investigate the long-term dynamic mechanical properties of CTB.The stress-strain relationship,dynamic strength,and dynamic failure characteristics of CTB specimens are analyzed and discussed to provide valuable conclusions that will improve our knowledge of CTB long-term mechanical behavior and characteristics.For instance,the dynamic peak stress under cyclic impact loading is approximately twice that under single impact loading,and the CTB specimens are less prone to fracture when cyclically loaded.These findings and conclusions can provide a new set of references for the stability analysis of CTB materials and help guide mine designers in reducing the amount of binding agents and the associated mining cost.
基金the support of the National Natural Science Foundation of China (Grant No.50774086 and 50874109)
文摘We studied the dynamic fracture mechanical behavior of rock under different impact rates. The fracture experiment was a three-point bending beam subjected to different impact loads monitored using the reflected caustics method. The mechanical parameters for fracture of the three-poim bending beam specimen under impact load are analyzed. The mechanism of crack propagation is discussed. Experimental results show that the dynamic stress intensity factor increases before crack initiation. When the dynamic stress intensity factor reaches its maximum value the crack starts to develop. After crack initiation the dynamic stress intensity factor decreases rapidly and oscillates. As the impact rate increases the cracks initiate earlier, the maximum value of crack growth velocity becomes smaller and the values of dynamic stress intensity factor also vary less during crack propagation. The results provide a theoretical basis for the study of rock dynamic fracture.
基金This work was financially supported by the National Natural Science Foundation of China(Grant Nos.U19A2098,11672194 and 11702181)the Fundamental Research Funds for the Central Universities.
文摘Crack dynamic propagation and arrest behaviors have received extensive attention over the years.However,there still remain many questions,e.g.under what conditions will a running crack come to arrest?In this paper,drop weight impact(DWI)tests were conducted to investigate crack arrest mechanism using single cleavage triangle(SCT)rock specimens.Green sandstone was selected to prepare the SCT specimens.Dynamic stress intensity factors(DSIFs)were calculated by ABAQUS code,and the critical DSIFs were determined by crack propagation speeds and fracture time measured by crack propagation gauges(CPGs).The test results show that the critical DSIF at propagation decreases with crack propagation speed.Numerical simulation for SCT specimens under different loading waves was performed using AUTODYN code.The reflected compressive wave from the incident and transmitted plates can induce crack arrests during propagation,and the number of arrest times increases with the wave length.In order to eliminate the effect of the incident and transmitted plates,models consisting of only one SCT specimen without incident and transmitted plates were established,and the same trapezoid-shaped loading wave was applied to the SCT specimen.The results show that for the SCT specimen with transmitted boundary(analogous to an infinite plate),the trapezoid-shaped loading wave cannot induce crack arrest anymore.The numerical results can well describe the occurrence of crack arrest in the experiments.
文摘The transient response of an unlimited cylindrical cavity buried in the infinite elastic soil subjected to an anti-plane impact load along the cavern axis direction was studied.Using Laplace transform combining with contour integral of the Laplace inverse transform specifically,the general analytical expressions of the soil displacement and stress are obtained in the time domain,respectively.And the numerical solutions of the problem computed by analytical expressions are presented.In the time domain,the dynamic responses of the infinite elastic soil are analyzed,and the calculation results are compared with those from numerical inversion proposed by Durbin and the static results.One observes good agreement between analytical and numerical inversion results,lending the further support to the method presented.Finally,some valuable shear wave propagation laws are gained: the displacement of the soil remains zero before the wave arrival,and after the shear wave arrival,the stress and the displacement at this point increase abruptly,then reduce and tend to the static value gradually at last.The wave attenuates along the radial,therefore the farther the wave is from the source,the smaller the stress and the displacement are,and the stress and the displacement are just functions of the radial distance from the axis.
基金the financial support provided by Natural Science and Engineering Research Council of Canada (NSERC) Grant No: RGPIN-2014-03992
文摘Impact-induced damage to jointed rock masses has important consequences in various mining and civil engineering applications. This paper reports a numerical investigation to address the responses of jointed rock masses subjected to impact loading. It also focuses on the static and dynamic properties of an intact rock derived from a series of laboratory tests on meta-sandstone samples from a quarry in Nova Scotia, Canada. A distinct element code(PFC2D) was used to generate a bonded particle model(BPM) to simulate both the static and dynamic properties of the intact rock. The calibrated BPM was then used to construct large-scale jointed rock mass samples by incorporating discrete joint networks of multiple joint intensities into the intact rock matrix represented by the BPM. Finally, the impact-induced damage inflicted by a rigid projectile particle on the jointed rock mass samples was determined through the use of the numerical model. The simulation results show that joints play an important role in the impactinduced rock mass damage where higher joint intensity results in more damage to the rock mass. This is mainly attributed to variations of stress wave propagation in jointed rock masses as compared to intact rock devoid of joints.
基金supported by the National Natural Science Foundation of China(Nos.52071139,51905166,52075167)well as from the Natural Science Foundation of Hunan Province(2020JJ5198)the Open Platform Fund of Hunan Institute of Technology(KFA20014).
文摘Split Hopkinson pressure bar(SHPB)tests were conducted on pre-rolled AZ31 magnesium alloy at 150–350℃ with strain rates of 2150s-1,3430s^(-1) and 4160s-1.The mechanical response,microstructural evolution and accommodation mechanism of the pre-rolled AZ31 magnesium alloy under high-speed impact loading were investigated.The twin and shear band are prevailing at low temperature,and the coexistence of twins and recrystallized grains is the dominant microstructure at medium temperature,while at high temperature,dynamic recrystallization(DRX)is almost complete.The increment of temperature reduces the critical condition difference between twinning and DRX,and the recrystallized temperature decreases with increasing strain rate.The mechanical response is related to the competition among the shear band strengthen,the twin strengthen and the fine grain strengthen and determined by the prevailing grain structure.The fine grain strengthen could compensate soften caused by the temperature increase and the reduction of twin and shear band.During high-speed deformation,different twin variants,introduced by pre-rolling,induce different deformation mechanism to accommodate plastic deformation and are in favor for non-basal slip.At low temperature,the high-speed deformation is achieved by twinning,dislocation slip and the following deformation shear band at different deformation stages.At high temperature,the high-speed deformation is realized by twinning and dislocation slip of early deformation stage,transition shear band of medium deformation stage and DRX of final deformation stage.
