冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进...冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。展开更多
The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from...The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).展开更多
Gait recognition is a key biometric for long-distance identification,yet its performance is severely degraded by real-world challenges such as varying clothing,carrying conditions,and changing viewpoints.While combini...Gait recognition is a key biometric for long-distance identification,yet its performance is severely degraded by real-world challenges such as varying clothing,carrying conditions,and changing viewpoints.While combining silhouette and skeleton data is a promising direction,effectively fusing these heterogeneous modalities and adaptively weighting their contributions in response to diverse conditions remains a central problem.This paper introduces GaitMAFF,a novelMulti-modal Adaptive Feature Fusion Network,to address this challenge.Our approach first transforms discrete skeleton joints into a dense SkeletonMap representation to align with silhouettes,then employs an attention-based module to dynamically learn the fusion weights between the two modalities.These fused features are processed by a powerful spatio-temporal backbone withWeighted Global-Local Feature FusionModules(WFFM)to learn a discriminative representation.Extensive experiments on the challenging CCPG and Gait3D datasets show that GaitMAFF achieves state-of-the-art performance,with an average Rank-1 accuracy of 84.6%on CCPG and 58.7%on Gait3D.These results demonstrate that our adaptive fusion strategy effectively integrates complementary multimodal information,significantly enhancing gait recognition robustness and accuracy in complex scenes and providing a practical solution for real-world applications.展开更多
Image-maps,a hybrid design with satellite images as background and map symbols uploaded,aim to combine the advantages of maps’high interpretation efficiency and satellite images’realism.The usability of image-maps i...Image-maps,a hybrid design with satellite images as background and map symbols uploaded,aim to combine the advantages of maps’high interpretation efficiency and satellite images’realism.The usability of image-maps is influenced by the representations of background images and map symbols.Many researchers explored the optimizations for background images and symbolization techniques for symbols to reduce the complexity of image-maps and improve the usability.However,little literature was found for the optimum amount of symbol loading.This study focuses on the effects of background image complexity and map symbol load on the usability(i.e.,effectiveness and efficiency)of image-maps.Experiments were conducted by user studies via eye-tracking equipment and an online questionnaire survey.Experimental data sets included image-maps with ten levels of map symbol load in ten areas.Forty volunteers took part in the target searching experiments.It has been found that the usability,i.e.,average time viewed(efficiency)and average revisits(effectiveness)of targets recorded,is influenced by the complexity of background images,a peak exists for optimum symbol load for an image-map.The optimum levels for symbol load for different image-maps also have a peak when the complexity of the background image/image map increases.The complexity of background images serves as a guideline for optimum map symbol load in image-map design.This study enhanced user experience by optimizing visual clarity and managing cognitive load.Understanding how these factors interact can help create adaptive maps that maintain clarity and usability,guiding AI algorithms to adjust symbol density based on user context.This research establishes the practices for map design,making cartographic tools more innovative and more user-centric.展开更多
Topographic maps,as essential tools and sources of information for geographic research,contain precise spatial locations and rich map features,and they illustrate spatio-temporal information on the distribution and di...Topographic maps,as essential tools and sources of information for geographic research,contain precise spatial locations and rich map features,and they illustrate spatio-temporal information on the distribution and differences of various surface features.Currently,topographic maps are mainly stored in raster and vector formats.Extraction of the spatio-temporal knowledge in the maps—such as spatial distribution patterns,feature relationships,and dynamic evolution—still primarily relies on manual interpretation.However,manual interpretation is time-consuming and laborious,especially for large-scale,long-term map knowledge extraction and application.With the development of artificial intelligence technology,it is possible to improve the automation level of map knowledge interpretation.Therefore,the present study proposes an automatic interpretation method for raster topographic map knowledge based on deep learning.To address the limitations of current data-driven intelligent technology in learning map spatial relations and cognitive logic,we establish a formal description of map knowledge by mapping the relationship between map knowledge and features,thereby ensuring interpretation accuracy.Subsequently,deep learning techniques are employed to extract map features automatically,and the spatio-temporal knowledge is constructed by combining formal descriptions of geographic feature knowledge.Validation experiments demonstrate that the proposed method effectively achieves automatic interpretation of spatio-temporal knowledge of geographic features in maps,with an accuracy exceeding 80%.The findings of the present study contribute to machine understanding of spatio-temporal differences in map knowledge and advances the intelligent interpretation and utilization of cartographic information.展开更多
Hot compression tests for GH4706 alloy were performed at a true strain of 1.2 within the temperature range of 950-1150℃ and the strain rate range of 0.001-1 s^(-1).The optimal hot deformation temperature and strain r...Hot compression tests for GH4706 alloy were performed at a true strain of 1.2 within the temperature range of 950-1150℃ and the strain rate range of 0.001-1 s^(-1).The optimal hot deformation temperature and strain rate range were determined using nephogram maps of dynamic recrystallization fraction,average grain size,and grain distribution standard deviation.Processing maps at true strains from 0.4 to 0.9 were generated based on flow stress curves to identify the strain corresponding to optimal microstructure homogenization efficiency at various temperatures and strain rates.Results show that within the optimal parameter range,under the conditions of 1150℃ and 0.01 s^(-1),the true strain of about 0.6 results in the optimal microstructure homogenization efficiency.The grain orientation spread maps obtained from the experiment also confirms this conclusion.This study provides an effective method for microstructure homogenization control of GH4706 alloy and an effective reference for the minimum strain threshold of the local part of the forging in engineering.展开更多
Data security has become a growing priority due to the increasing frequency of cyber-attacks,necessitating the development of more advanced encryption algorithms.This paper introduces Single Qubit Quantum Logistic-Sin...Data security has become a growing priority due to the increasing frequency of cyber-attacks,necessitating the development of more advanced encryption algorithms.This paper introduces Single Qubit Quantum Logistic-Sine XYZ-Rotation Maps(SQQLSR),a quantum-based chaos map designed to generate one-dimensional chaotic sequences with an ultra-wide parameter range.The proposed model leverages quantum superposition using Hadamard gates and quantum rotations along the X,Y,and Z axes to enhance randomness.Extensive numerical experiments validate the effectiveness of SQQLSR.The proposed method achieves a maximum Lyapunov exponent(LE)of≈55.265,surpassing traditional chaotic maps in unpredictability.The bifurcation analysis confirms a uniform chaotic distribution,eliminating periodic windows and ensuring higher randomness.The system also generates an expanded key space exceeding 10^(40),enhancing security against brute-force attacks.Additionally,SQQLSR is applied to image encryption using a simple three-layer encryption scheme combining permutation and substitution techniques.This approach is intentionally designed to highlight the impact of SQQLSR-generated chaotic sequences rather than relying on a complex encryption algorithm.Theencryption method achieves an average entropy of 7.9994,NPCR above 99.6%,and UACI within 32.8%–33.8%,confirming its strong randomness and sensitivity to minor modifications.The robustness tests against noise,cropping,and JPEG compression demonstrate its resistance to statistical and differential attacks.Additionally,the decryption process ensures perfect image reconstruction with an infinite PSNR value,proving the algorithm’s reliability.These results highlight SQQLSR’s potential as a lightweight yet highly secure encryption mechanism suitable for quantum cryptography and secure communications.展开更多
Assessing forest vulnerability to disturbances at a high spatial resolution and for regional and national scales has become attainable with the combination of remote sensing-derived high-resolution forest maps and mec...Assessing forest vulnerability to disturbances at a high spatial resolution and for regional and national scales has become attainable with the combination of remote sensing-derived high-resolution forest maps and mechanistic risk models. This study demonstrated large-scale and high-resolution modelling of wind damage vulnerability in Norway. The hybrid mechanistic wind damage model, ForestGALES, was adapted to map the critical wind speeds(CWS) of damage across Norway using a national forest attribute map at a 16 m × 16 m spatial resolution. P arametrization of the model for the Norwegian context was done using the literature and the National Forest Inventory data. This new parametrization of the model for Norwegian forests yielded estimates of CWS significantly different from the default parametrization. Both parametrizations fell short of providing acceptable discrimination of the damaged area following the storm of November 19, 2021 in the central southern region of Norway when using unadjusted CWS. After adjusting the CWS and the storm wind speeds by a constant factor, the Norwegian parametrization provided acceptable discrimination and was thus defined as suitable to use in future studies, despite the lack of field-and laboratory experiments to directly derive parameters for Norwegian forests. The windstorm event used for model validation in this study highlighted the challenges of predicting wind damage to forests in landscapes with complex topography. Future studies should focus on further developing ForestGALES and new datasets describing extreme wind climates to better represent the wind and tree interactions in complex topography, and predict the level of risk in order to develop local climate-smart forest management strategies.展开更多
Conventional soil maps(CSMs)often have multiple soil types within a single polygon,which hinders the ability of machine learning to accurately predict soils.Soil disaggregation approaches are commonly used to improve ...Conventional soil maps(CSMs)often have multiple soil types within a single polygon,which hinders the ability of machine learning to accurately predict soils.Soil disaggregation approaches are commonly used to improve the spatial and attribute precision of CSMs.The approach disaggregation and harmonization of soil map units through resampled classification trees(DSMART)is popular but computationally intensive,as it generates and assigns synthetic samples to soil series based on the areal coverage information of CSMs.Alternatively,the disaggregation approach pure polygon disaggregation(PPD)assigns soil series based solely on the proportions of soil series in pure polygons in CSMs.This study compared these two disaggregation approaches by applying them to a CSM of Middlesex County,Ontario,Canada.Four different sampling methods were used:two sampling designs,simple random sampling(SRS)and conditional Latin hypercube sampling(cLHS),with two sample sizes(83100 and 19420 samples per sampling plan),both based on an area-weighted approach.Two machine learning algorithms(MLAs),C5.0 decision tree(C5.0)and random forest(RF),were applied to the disaggregation approaches to compare the disaggregation accuracy.The accuracy assessment utilized a set of 500 validation points obtained from the Middlesex County soil survey report.The MLA C5.0(Kappa index=0.58–0.63)showed better performance than RF(Kappa index=0.53–0.54)based on the larger sample size,and PPD with C5.0 based on the larger sample size was the best-performing(Kappa index=0.63)approach.Based on the smaller sample size,both cLHS(Kappa index=0.41–0.48)and SRS(Kappa index=0.40–0.47)produced similar accuracy results.The disaggregation approach PPD exhibited lower processing capacity and time demands(1.62–5.93 h)while yielding maps with lower uncertainty as compared to DSMART(2.75–194.2 h).For CSMs predominantly composed of pure polygons,utilizing PPD for soil series disaggregation is a more efficient and rational choice.However,DSMART is the preferable approach for disaggregating soil series that lack pure polygon representations in the CSMs.展开更多
The advent of 6G wireless networks promises unprecedented connectivity,supporting ultra-high data rates,low latency,and massive device connectivity.However,these ambitious goals introduce significant challenges,partic...The advent of 6G wireless networks promises unprecedented connectivity,supporting ultra-high data rates,low latency,and massive device connectivity.However,these ambitious goals introduce significant challenges,particularly in channel estimation due to complex and dynamic propagation environments.This paper explores the concept of channel knowledge maps(CKMs)as a solution to these challenges.CKMs enable environment-aware communications by providing location-specific channel information,reducing reliance on real-time pilot measurements.We categorize CKM construction techniques into measurement-based,model-based,and hybrid methods,and examine their key applications in integrated sensing and communication(ISAC)systems,beamforming,trajectory optimization of unmanned aerial vehicles(UAVs),base station(BS)placement,and resource allocation.Furthermore,we discuss open challenges and propose future research directions to enhance the robustness,accuracy,and scalability of CKM-based systems in the evolving 6G landscape.展开更多
In this paper,we introduce the notion of f-CC harmonic maps with potential H from a Riemannian manifold into sub-Riemannian manifolds,and achieve some vanishing theorems for f-CC harmonic maps with potential H via the...In this paper,we introduce the notion of f-CC harmonic maps with potential H from a Riemannian manifold into sub-Riemannian manifolds,and achieve some vanishing theorems for f-CC harmonic maps with potential H via the stress-energy tensor and the monotonicity formulas.展开更多
Background Zonal application maps are designed to represent field variability using key variables that can be translated into tailored management practices.For cotton,zonal maps for crop growth regulator(CGR)applicati...Background Zonal application maps are designed to represent field variability using key variables that can be translated into tailored management practices.For cotton,zonal maps for crop growth regulator(CGR)applications under variable-rate(VR)strategies are commonly based exclusively on vegetation indices(VIs)variability.However,VIs often saturate in dense crop vegetation areas,limiting their effectiveness in distinguishing variability in crop growth.This study aimed to compare unsupervised framework(UF)and supervised framework(SUF)approaches for generat-ing zonal application maps for CGR under VR conditions.During 2022-2023 agricultural seasons,an UF was employed to generate zonal maps based on locally collected field data on plant height of cotton,satellite imagery,soil texture,and phenology data.Subsequently,a SUF(based on historical data between 2020-2021 to 2022-2023 agricultural seasons)was developed to predict plant height using remote sensing and phenology data,aiming to replicate same zonal maps but without relying on direct field measurements of plant height.Both approaches were tested in three fields and on two different dates per field.Results The predictive model for plant height of SUF performed well,as indicated by the model metrics.However,when comparing zonal application maps for specific field-date combinations,the predicted plant height exhibited lower variability compared with field measurements.This led to variable compatibility between SUF maps,which utilized the model predictions,and the UF maps,which were based on the real field data.Fields characterized by much pronounced soil texture variability yielded the highest compatibility between the zonal application maps produced by both SUF and UF approaches.This was predominantly due to the greater consistency in estimating plant development patterns within these heterogeneous field environments.While VR application approach can facilitate product savings during the application operation,other key factors must be considered.These include the availability of specialized machinery required for this type of applications,as well as the inherent operational costs associated with applying a single CGR product which differs from the typical uniform rate applications that often integrate multi-ple inputs.Conclusion Predictive modeling shows promise for assisting in the creation of zonal application maps for VR of CGR applications.However,the degree of agreement with the actual variability in crop growth found in the field should be evaluated on a field-by-field basis.The SUF approach,which is based on plant heigh prediction,demonstrated potential for supporting the development of zonal application maps for VR of CGR applications.However,the degree to which this approach aligns itself with the actual variability in crop growth observed in the field may vary,necessi-tating field-by-field evaluation.展开更多
With the increasing exploration of oil and gas into deep waters,the necessity for material development increases for lighter conduits such as composite marine risers,in the oil and gas industry.To understand the resea...With the increasing exploration of oil and gas into deep waters,the necessity for material development increases for lighter conduits such as composite marine risers,in the oil and gas industry.To understand the research knowledge on this novel area,there is a need to have a bibliometric analysis on composite marine risers.A research methodology was developed whereby the data retrieval was from SCOPUS database from 1977–2023.Then,VOSviewer was used to visualize the knowledge maps.This study focuses on the progress made by conducting knowledge mapping and scientometric review on composite marine risers.This scientometric analysis on the subject shows current advances,geographical activities by countries,authorship records,collaborations,funders,affiiliations,co‑occurrences,and future research areas.It was observed that the research trends recorded the highest publication volume in the U.S.A.,but less cluster affiiliated,as it was followed by countries like the U.K.,China,Nigeria,Australia and Singapore.Also,thisfiield has more conference papers than journal papers due to the challenge of adaptability,acceptance,qualifiication,and application of composite marine risers in the marine industry.Hence,there is a need for more collaborations on composite marine risers and more funding to enhance the research trend.展开更多
Water quality is a critical global issue,especially in urban and semi-urban regions where natural and anthropogenic factors significantly influence surface water systems.This study evaluates the hydrochemical characte...Water quality is a critical global issue,especially in urban and semi-urban regions where natural and anthropogenic factors significantly influence surface water systems.This study evaluates the hydrochemical characteristics of surface water in the North of Tehran Rivers(NTRs),an essential water resource in a rapidly urbanizing region,using advanced clustering techniques,including Hierarchical Clustering Analysis(HCA),Fuzzy CMeans(FCM),Genetic Algorithm Fuzzy C-Means(GAFCM),and Self-Organizing Map(SOM).The research aims to address the scientific challenge of understanding spatial and temporal variability in water quality,focusing on physicochemical parameters,hydrochemical facies,and contamination sources.Water samples from six rivers collected over four seasons in 2020 were analyzed and classified into distinct clusters based on their chemical composition,revealing significant seasonal and spatial differences.Results showed that FCM and GAFCM consistently categorized the NTRs into two clusters during winter and spring and three in summer and autumn.These findings were supported by HCA and SOM,which identified clusters corresponding to specific river segments and contamination levels.The primary hydrochemical processes identified were mineral dissolution and weathering,with calcite,dolomite,and aragonite significantly influencing water chemistry.Additionally,human activities,such as wastewater discharge,were shown to contribute to elevated sulfate,nitrate,and phosphate concentrations,further corroborated by microbial analyses.By integrating HCA,FCM,and GAFCM with an artificial neural network(ANN)-based clustering method(SOM),this study provides a robust framework for evaluating surface water quality.The findings,supported by Gibbs diagrams,Hounslow ion ratio,and saturation indices,highlight the dominance of rock weathering and human impacts in shaping the hydrochemical dynamics of the NTRs.These insights contribute to the scientific understanding of water quality dynamics and offer practical guidance for sustainable water resource management and environmental protection in developing urban areas.展开更多
The title of the online version of the original article was revised.The title of the original article has been revised to:Hydrochemical characterization of surface waters in Northern Tehran:Integrating cluster-based t...The title of the online version of the original article was revised.The title of the original article has been revised to:Hydrochemical characterization of surface waters in Northern Tehran:Integrating cluster-based techniques with Self-Organizing Maps.展开更多
Automatic segmentation and recognition of content and element information in color geological map are of great significance for researchers to analyze the distribution of mineral resources and predict disaster informa...Automatic segmentation and recognition of content and element information in color geological map are of great significance for researchers to analyze the distribution of mineral resources and predict disaster information.This article focuses on color planar raster geological map(geological maps include planar geological maps,columnar maps,and profiles).While existing deep learning approaches are often used to segment general images,their performance is limited due to complex elements,diverse regional features,and complicated backgrounds for color geological map in the domain of geoscience.To address the issue,a color geological map segmentation model is proposed that combines the Felz clustering algorithm and an improved SE-UNet deep learning network(named GeoMSeg).Firstly,a symmetrical encoder-decoder structure backbone network based on UNet is constructed,and the channel attention mechanism SENet has been incorporated to augment the network’s capacity for feature representation,enabling the model to purposefully extract map information.The SE-UNet network is employed for feature extraction from the geological map and obtain coarse segmentation results.Secondly,the Felz clustering algorithm is used for super pixel pre-segmentation of geological maps.The coarse segmentation results are refined and modified based on the super pixel pre-segmentation results to obtain the final segmentation results.This study applies GeoMSeg to the constructed dataset,and the experimental results show that the algorithm proposed in this paper has superior performance compared to other mainstream map segmentation models,with an accuracy of 91.89%and a MIoU of 71.91%.展开更多
文摘冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。
基金Sichuan Science and Technology Program(2025ZNSFSC1341)Fundamental Research Funds for the Central Universities(J2022-090,25CAFUC04087)。
文摘The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).
基金funded by the Natural Science Foundation of Chongqing Municipality,grant number CSTB2022NSCQ-MSX0503.
文摘Gait recognition is a key biometric for long-distance identification,yet its performance is severely degraded by real-world challenges such as varying clothing,carrying conditions,and changing viewpoints.While combining silhouette and skeleton data is a promising direction,effectively fusing these heterogeneous modalities and adaptively weighting their contributions in response to diverse conditions remains a central problem.This paper introduces GaitMAFF,a novelMulti-modal Adaptive Feature Fusion Network,to address this challenge.Our approach first transforms discrete skeleton joints into a dense SkeletonMap representation to align with silhouettes,then employs an attention-based module to dynamically learn the fusion weights between the two modalities.These fused features are processed by a powerful spatio-temporal backbone withWeighted Global-Local Feature FusionModules(WFFM)to learn a discriminative representation.Extensive experiments on the challenging CCPG and Gait3D datasets show that GaitMAFF achieves state-of-the-art performance,with an average Rank-1 accuracy of 84.6%on CCPG and 58.7%on Gait3D.These results demonstrate that our adaptive fusion strategy effectively integrates complementary multimodal information,significantly enhancing gait recognition robustness and accuracy in complex scenes and providing a practical solution for real-world applications.
基金National Natural Science Foundation of China(No.42301518)Hubei Key Laboratory of Regional Development and Environmental Response(No.2023(A)002)Key Laboratory of the Evaluation and Monitoring of Southwest Land Resources(Ministry of Education)(No.TDSYS202304).
文摘Image-maps,a hybrid design with satellite images as background and map symbols uploaded,aim to combine the advantages of maps’high interpretation efficiency and satellite images’realism.The usability of image-maps is influenced by the representations of background images and map symbols.Many researchers explored the optimizations for background images and symbolization techniques for symbols to reduce the complexity of image-maps and improve the usability.However,little literature was found for the optimum amount of symbol loading.This study focuses on the effects of background image complexity and map symbol load on the usability(i.e.,effectiveness and efficiency)of image-maps.Experiments were conducted by user studies via eye-tracking equipment and an online questionnaire survey.Experimental data sets included image-maps with ten levels of map symbol load in ten areas.Forty volunteers took part in the target searching experiments.It has been found that the usability,i.e.,average time viewed(efficiency)and average revisits(effectiveness)of targets recorded,is influenced by the complexity of background images,a peak exists for optimum symbol load for an image-map.The optimum levels for symbol load for different image-maps also have a peak when the complexity of the background image/image map increases.The complexity of background images serves as a guideline for optimum map symbol load in image-map design.This study enhanced user experience by optimizing visual clarity and managing cognitive load.Understanding how these factors interact can help create adaptive maps that maintain clarity and usability,guiding AI algorithms to adjust symbol density based on user context.This research establishes the practices for map design,making cartographic tools more innovative and more user-centric.
基金Deep-time Digital Earth(DDE)Big Science Program(No.GJ-C03-SGF-2025-004)National Natural Science Foundation of China(No.42394063)Sichuan Science and Technology Program(No.2025ZNSFSC0325).
文摘Topographic maps,as essential tools and sources of information for geographic research,contain precise spatial locations and rich map features,and they illustrate spatio-temporal information on the distribution and differences of various surface features.Currently,topographic maps are mainly stored in raster and vector formats.Extraction of the spatio-temporal knowledge in the maps—such as spatial distribution patterns,feature relationships,and dynamic evolution—still primarily relies on manual interpretation.However,manual interpretation is time-consuming and laborious,especially for large-scale,long-term map knowledge extraction and application.With the development of artificial intelligence technology,it is possible to improve the automation level of map knowledge interpretation.Therefore,the present study proposes an automatic interpretation method for raster topographic map knowledge based on deep learning.To address the limitations of current data-driven intelligent technology in learning map spatial relations and cognitive logic,we establish a formal description of map knowledge by mapping the relationship between map knowledge and features,thereby ensuring interpretation accuracy.Subsequently,deep learning techniques are employed to extract map features automatically,and the spatio-temporal knowledge is constructed by combining formal descriptions of geographic feature knowledge.Validation experiments demonstrate that the proposed method effectively achieves automatic interpretation of spatio-temporal knowledge of geographic features in maps,with an accuracy exceeding 80%.The findings of the present study contribute to machine understanding of spatio-temporal differences in map knowledge and advances the intelligent interpretation and utilization of cartographic information.
基金National Key R&D Program Project(2022YFB3705103)。
文摘Hot compression tests for GH4706 alloy were performed at a true strain of 1.2 within the temperature range of 950-1150℃ and the strain rate range of 0.001-1 s^(-1).The optimal hot deformation temperature and strain rate range were determined using nephogram maps of dynamic recrystallization fraction,average grain size,and grain distribution standard deviation.Processing maps at true strains from 0.4 to 0.9 were generated based on flow stress curves to identify the strain corresponding to optimal microstructure homogenization efficiency at various temperatures and strain rates.Results show that within the optimal parameter range,under the conditions of 1150℃ and 0.01 s^(-1),the true strain of about 0.6 results in the optimal microstructure homogenization efficiency.The grain orientation spread maps obtained from the experiment also confirms this conclusion.This study provides an effective method for microstructure homogenization control of GH4706 alloy and an effective reference for the minimum strain threshold of the local part of the forging in engineering.
基金funded by Kementerian Pendidikan Tinggi,Sains,dan Teknologi(Kemdiktisaintek),Indonesia,grant numbers 108/E5/PG.02.00.PL/2024,027/LL6/PB/AL.04/2024,061/A.38-04/UDN-09/VI/2024.
文摘Data security has become a growing priority due to the increasing frequency of cyber-attacks,necessitating the development of more advanced encryption algorithms.This paper introduces Single Qubit Quantum Logistic-Sine XYZ-Rotation Maps(SQQLSR),a quantum-based chaos map designed to generate one-dimensional chaotic sequences with an ultra-wide parameter range.The proposed model leverages quantum superposition using Hadamard gates and quantum rotations along the X,Y,and Z axes to enhance randomness.Extensive numerical experiments validate the effectiveness of SQQLSR.The proposed method achieves a maximum Lyapunov exponent(LE)of≈55.265,surpassing traditional chaotic maps in unpredictability.The bifurcation analysis confirms a uniform chaotic distribution,eliminating periodic windows and ensuring higher randomness.The system also generates an expanded key space exceeding 10^(40),enhancing security against brute-force attacks.Additionally,SQQLSR is applied to image encryption using a simple three-layer encryption scheme combining permutation and substitution techniques.This approach is intentionally designed to highlight the impact of SQQLSR-generated chaotic sequences rather than relying on a complex encryption algorithm.Theencryption method achieves an average entropy of 7.9994,NPCR above 99.6%,and UACI within 32.8%–33.8%,confirming its strong randomness and sensitivity to minor modifications.The robustness tests against noise,cropping,and JPEG compression demonstrate its resistance to statistical and differential attacks.Additionally,the decryption process ensures perfect image reconstruction with an infinite PSNR value,proving the algorithm’s reliability.These results highlight SQQLSR’s potential as a lightweight yet highly secure encryption mechanism suitable for quantum cryptography and secure communications.
基金funded by the Norwegian Research Council(NFR project 302701 Climate Smart Forestry Norway).
文摘Assessing forest vulnerability to disturbances at a high spatial resolution and for regional and national scales has become attainable with the combination of remote sensing-derived high-resolution forest maps and mechanistic risk models. This study demonstrated large-scale and high-resolution modelling of wind damage vulnerability in Norway. The hybrid mechanistic wind damage model, ForestGALES, was adapted to map the critical wind speeds(CWS) of damage across Norway using a national forest attribute map at a 16 m × 16 m spatial resolution. P arametrization of the model for the Norwegian context was done using the literature and the National Forest Inventory data. This new parametrization of the model for Norwegian forests yielded estimates of CWS significantly different from the default parametrization. Both parametrizations fell short of providing acceptable discrimination of the damaged area following the storm of November 19, 2021 in the central southern region of Norway when using unadjusted CWS. After adjusting the CWS and the storm wind speeds by a constant factor, the Norwegian parametrization provided acceptable discrimination and was thus defined as suitable to use in future studies, despite the lack of field-and laboratory experiments to directly derive parameters for Norwegian forests. The windstorm event used for model validation in this study highlighted the challenges of predicting wind damage to forests in landscapes with complex topography. Future studies should focus on further developing ForestGALES and new datasets describing extreme wind climates to better represent the wind and tree interactions in complex topography, and predict the level of risk in order to develop local climate-smart forest management strategies.
基金the Ontario Ministry of Agriculture,Food and Rural Affairs,Canada,who supported this project by providing updated soil information on Ontario and Middlesex Countysupported by the Natural Science and Engineering Research Council of Canada(No.RGPIN-2014-4100)。
文摘Conventional soil maps(CSMs)often have multiple soil types within a single polygon,which hinders the ability of machine learning to accurately predict soils.Soil disaggregation approaches are commonly used to improve the spatial and attribute precision of CSMs.The approach disaggregation and harmonization of soil map units through resampled classification trees(DSMART)is popular but computationally intensive,as it generates and assigns synthetic samples to soil series based on the areal coverage information of CSMs.Alternatively,the disaggregation approach pure polygon disaggregation(PPD)assigns soil series based solely on the proportions of soil series in pure polygons in CSMs.This study compared these two disaggregation approaches by applying them to a CSM of Middlesex County,Ontario,Canada.Four different sampling methods were used:two sampling designs,simple random sampling(SRS)and conditional Latin hypercube sampling(cLHS),with two sample sizes(83100 and 19420 samples per sampling plan),both based on an area-weighted approach.Two machine learning algorithms(MLAs),C5.0 decision tree(C5.0)and random forest(RF),were applied to the disaggregation approaches to compare the disaggregation accuracy.The accuracy assessment utilized a set of 500 validation points obtained from the Middlesex County soil survey report.The MLA C5.0(Kappa index=0.58–0.63)showed better performance than RF(Kappa index=0.53–0.54)based on the larger sample size,and PPD with C5.0 based on the larger sample size was the best-performing(Kappa index=0.63)approach.Based on the smaller sample size,both cLHS(Kappa index=0.41–0.48)and SRS(Kappa index=0.40–0.47)produced similar accuracy results.The disaggregation approach PPD exhibited lower processing capacity and time demands(1.62–5.93 h)while yielding maps with lower uncertainty as compared to DSMART(2.75–194.2 h).For CSMs predominantly composed of pure polygons,utilizing PPD for soil series disaggregation is a more efficient and rational choice.However,DSMART is the preferable approach for disaggregating soil series that lack pure polygon representations in the CSMs.
基金supported by the National Natural Science Foundation of China under Grants Nos.62431014 and 62271310the Fundamental Research Funds for the Central Universities of China。
文摘The advent of 6G wireless networks promises unprecedented connectivity,supporting ultra-high data rates,low latency,and massive device connectivity.However,these ambitious goals introduce significant challenges,particularly in channel estimation due to complex and dynamic propagation environments.This paper explores the concept of channel knowledge maps(CKMs)as a solution to these challenges.CKMs enable environment-aware communications by providing location-specific channel information,reducing reliance on real-time pilot measurements.We categorize CKM construction techniques into measurement-based,model-based,and hybrid methods,and examine their key applications in integrated sensing and communication(ISAC)systems,beamforming,trajectory optimization of unmanned aerial vehicles(UAVs),base station(BS)placement,and resource allocation.Furthermore,we discuss open challenges and propose future research directions to enhance the robustness,accuracy,and scalability of CKM-based systems in the evolving 6G landscape.
基金Supported by the National Natural Science Foundation of China(12271254,12141104,12571056)supported by Natural Science Foundation of Henan(252300421791,252300421497)。
文摘In this paper,we introduce the notion of f-CC harmonic maps with potential H from a Riemannian manifold into sub-Riemannian manifolds,and achieve some vanishing theorems for f-CC harmonic maps with potential H via the stress-energy tensor and the monotonicity formulas.
文摘Background Zonal application maps are designed to represent field variability using key variables that can be translated into tailored management practices.For cotton,zonal maps for crop growth regulator(CGR)applications under variable-rate(VR)strategies are commonly based exclusively on vegetation indices(VIs)variability.However,VIs often saturate in dense crop vegetation areas,limiting their effectiveness in distinguishing variability in crop growth.This study aimed to compare unsupervised framework(UF)and supervised framework(SUF)approaches for generat-ing zonal application maps for CGR under VR conditions.During 2022-2023 agricultural seasons,an UF was employed to generate zonal maps based on locally collected field data on plant height of cotton,satellite imagery,soil texture,and phenology data.Subsequently,a SUF(based on historical data between 2020-2021 to 2022-2023 agricultural seasons)was developed to predict plant height using remote sensing and phenology data,aiming to replicate same zonal maps but without relying on direct field measurements of plant height.Both approaches were tested in three fields and on two different dates per field.Results The predictive model for plant height of SUF performed well,as indicated by the model metrics.However,when comparing zonal application maps for specific field-date combinations,the predicted plant height exhibited lower variability compared with field measurements.This led to variable compatibility between SUF maps,which utilized the model predictions,and the UF maps,which were based on the real field data.Fields characterized by much pronounced soil texture variability yielded the highest compatibility between the zonal application maps produced by both SUF and UF approaches.This was predominantly due to the greater consistency in estimating plant development patterns within these heterogeneous field environments.While VR application approach can facilitate product savings during the application operation,other key factors must be considered.These include the availability of specialized machinery required for this type of applications,as well as the inherent operational costs associated with applying a single CGR product which differs from the typical uniform rate applications that often integrate multi-ple inputs.Conclusion Predictive modeling shows promise for assisting in the creation of zonal application maps for VR of CGR applications.However,the degree of agreement with the actual variability in crop growth found in the field should be evaluated on a field-by-field basis.The SUF approach,which is based on plant heigh prediction,demonstrated potential for supporting the development of zonal application maps for VR of CGR applications.However,the degree to which this approach aligns itself with the actual variability in crop growth observed in the field may vary,necessi-tating field-by-field evaluation.
基金support of the School of Engineering,Lancaster University,UK,for the Engineering Department Studentship as well as the Engineering and Physical Sciences Research Council(EPSRC)’s Doctoral Training Centre(DTC)。
文摘With the increasing exploration of oil and gas into deep waters,the necessity for material development increases for lighter conduits such as composite marine risers,in the oil and gas industry.To understand the research knowledge on this novel area,there is a need to have a bibliometric analysis on composite marine risers.A research methodology was developed whereby the data retrieval was from SCOPUS database from 1977–2023.Then,VOSviewer was used to visualize the knowledge maps.This study focuses on the progress made by conducting knowledge mapping and scientometric review on composite marine risers.This scientometric analysis on the subject shows current advances,geographical activities by countries,authorship records,collaborations,funders,affiiliations,co‑occurrences,and future research areas.It was observed that the research trends recorded the highest publication volume in the U.S.A.,but less cluster affiiliated,as it was followed by countries like the U.K.,China,Nigeria,Australia and Singapore.Also,thisfiield has more conference papers than journal papers due to the challenge of adaptability,acceptance,qualifiication,and application of composite marine risers in the marine industry.Hence,there is a need for more collaborations on composite marine risers and more funding to enhance the research trend.
文摘Water quality is a critical global issue,especially in urban and semi-urban regions where natural and anthropogenic factors significantly influence surface water systems.This study evaluates the hydrochemical characteristics of surface water in the North of Tehran Rivers(NTRs),an essential water resource in a rapidly urbanizing region,using advanced clustering techniques,including Hierarchical Clustering Analysis(HCA),Fuzzy CMeans(FCM),Genetic Algorithm Fuzzy C-Means(GAFCM),and Self-Organizing Map(SOM).The research aims to address the scientific challenge of understanding spatial and temporal variability in water quality,focusing on physicochemical parameters,hydrochemical facies,and contamination sources.Water samples from six rivers collected over four seasons in 2020 were analyzed and classified into distinct clusters based on their chemical composition,revealing significant seasonal and spatial differences.Results showed that FCM and GAFCM consistently categorized the NTRs into two clusters during winter and spring and three in summer and autumn.These findings were supported by HCA and SOM,which identified clusters corresponding to specific river segments and contamination levels.The primary hydrochemical processes identified were mineral dissolution and weathering,with calcite,dolomite,and aragonite significantly influencing water chemistry.Additionally,human activities,such as wastewater discharge,were shown to contribute to elevated sulfate,nitrate,and phosphate concentrations,further corroborated by microbial analyses.By integrating HCA,FCM,and GAFCM with an artificial neural network(ANN)-based clustering method(SOM),this study provides a robust framework for evaluating surface water quality.The findings,supported by Gibbs diagrams,Hounslow ion ratio,and saturation indices,highlight the dominance of rock weathering and human impacts in shaping the hydrochemical dynamics of the NTRs.These insights contribute to the scientific understanding of water quality dynamics and offer practical guidance for sustainable water resource management and environmental protection in developing urban areas.
文摘The title of the online version of the original article was revised.The title of the original article has been revised to:Hydrochemical characterization of surface waters in Northern Tehran:Integrating cluster-based techniques with Self-Organizing Maps.
基金financially supported by the Natural Science Foundation of China(42301492)the Open Fund of Hubei Key Laboratory of Intelligent Vision Based Monitoring for Hydroelectric Engineering(2022SDSJ04,2024SDSJ03)+1 种基金the Opening Fund of Key Laboratory of Geological Survey and Evaluation of Ministry of Education(GLAB 2023ZR01,GLAB2024ZR08)the Fundamental Research Funds for the Central Universities.
文摘Automatic segmentation and recognition of content and element information in color geological map are of great significance for researchers to analyze the distribution of mineral resources and predict disaster information.This article focuses on color planar raster geological map(geological maps include planar geological maps,columnar maps,and profiles).While existing deep learning approaches are often used to segment general images,their performance is limited due to complex elements,diverse regional features,and complicated backgrounds for color geological map in the domain of geoscience.To address the issue,a color geological map segmentation model is proposed that combines the Felz clustering algorithm and an improved SE-UNet deep learning network(named GeoMSeg).Firstly,a symmetrical encoder-decoder structure backbone network based on UNet is constructed,and the channel attention mechanism SENet has been incorporated to augment the network’s capacity for feature representation,enabling the model to purposefully extract map information.The SE-UNet network is employed for feature extraction from the geological map and obtain coarse segmentation results.Secondly,the Felz clustering algorithm is used for super pixel pre-segmentation of geological maps.The coarse segmentation results are refined and modified based on the super pixel pre-segmentation results to obtain the final segmentation results.This study applies GeoMSeg to the constructed dataset,and the experimental results show that the algorithm proposed in this paper has superior performance compared to other mainstream map segmentation models,with an accuracy of 91.89%and a MIoU of 71.91%.
