Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced s...Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced such as the form conditionand influential factors.Gas and coal dust explosion propagation was researched and thelifting process of coal dust was simulated.When an explosion occurred due to great mixtureof gas and air,the maximum explosion pressure appeared in the neighborhood of theexplosion source point.Before it propagated to the tunnel of the deposited coal dust,themaximum explosion pressure appeared to be in declining trend.Part of the energy waslost in the process of raising the deposited coal dust through a shock wave,so the maximumexplosion pressure was smallest on the foreside of the deposited coal dust sector.On the deposited coal dust sector,the explosion pressure rapidly increased and droppedoff after achieving the largest peak value.Because of coal dust participation in the explosion,the flame velocity rose rapidly on the deposited coal dust and achieved a basic stablevalue;coal dust was ignited to explode by initial laminar flame,and the laminar flametransformed into turbulent flame.The turbulence transformed the flame fold into a funnelshape and the shock wave interacted with the flame,so the combustion rate rose and thepressure wave was further enhanced.The regeneration mechanism between the flamecombustion rate and the aerodynamic flowing structure achieved the final critical state forforming the detonation.展开更多
A new method based on principal component analysis (PCA) and support vector machines (SVMs) is proposed for fault diagnosis of mine hoists. PCA is used to extract the principal features associated with the gearbox. Th...A new method based on principal component analysis (PCA) and support vector machines (SVMs) is proposed for fault diagnosis of mine hoists. PCA is used to extract the principal features associated with the gearbox. Then, with the irrelevant gearbox variables removed, the remaining gearbox, the hydraulic system and the wire rope parameters were used as input to a multi-class SVM. The SVM is first trained by using the one class-based multi-class optimization algorithm and it is then applied to fault identification. Comparison of various methods showed the PCA-SVM method successfully removed redundancy to solve the dimensionality curse. These results show that the algorithm using the RBF kernel function for the SVM had the best classification properties.展开更多
This paper aims to address the problem of geometric state control of large-segment steel box girders in offshore hoisting during the construction of large-span bridges. First, the geometric state control indexes of a ...This paper aims to address the problem of geometric state control of large-segment steel box girders in offshore hoisting during the construction of large-span bridges. First, the geometric state control indexes of a large-segment steel box girder are determined, such as the manufacturing parameters of the top and bottom slabs, the width of the annular joint, and the support position. Second, the geometric state equations and state transfer matrixes of large-segment steel box girders under different conditions are deduced by taking the mileage and elevation of control points as basic state variables. In application of the geometric state transfer method in the construction control of the Hong Kong-Zhuhai-Macao Bridge, the width of the annular joint and the position parameters for the support of the large-segment steel box girder are predicted precisely. Moreover, the manufacturing parameters of the top and bottom slabs of the steel box girders are calculated reliably. The measured values show that the width of the annular joint is basically the same with the difference of less than 2 mm, the eccentricity of bridge support is less than 20 mm, and the elevation error of the bridge deck is within-10 mm to +15 mm, which meets the construction accuracy. Using the geometric state transfer method, the rapid and accurate installation of the Hong Kong-Zhuhai-Macao Bridge has been realized, demonstrating that the precise control of the geometric state of a steel box girder with ectopic installation and multi-state transition can be realized by using the geometric state transfer method.展开更多
Using the mass of time-varying length balance rope focused on the hoisting conveyance, the coupling longi- tudinal-transverse model of mine friction hoist was established by using of the Hamilton＇s principle. The mod...Using the mass of time-varying length balance rope focused on the hoisting conveyance, the coupling longi- tudinal-transverse model of mine friction hoist was established by using of the Hamilton＇s principle. The modified Galerkin＇s method was used to discretize partial differential Eqs. The mine hoisting system was used to the example to analysis the relation between the load, velocity and transverse vibration of rope. The in situ tests were illustrated to evaluate the proposed mathematical model. The results showed that the modeling method can well represent the transverse vibration of rope.展开更多
In order to discover the airflow pattern in mine shaft which outfitted with hoist equipment （HE）, this paper set up the physical model and anatomized the piston-wind caused by hoist equipment, and researched the flo...In order to discover the airflow pattern in mine shaft which outfitted with hoist equipment （HE）, this paper set up the physical model and anatomized the piston-wind caused by hoist equipment, and researched the flow field and velocity field around the hoist equipment during its moving process, and analyzed the airflow around single and couple hoist equipment as well as decisive range of piston effect and additional effect of hoist equipment to ventilation system. Research conclusion indicate that during hoist equipment movement, airflow pattern changes repeatedly because of the influence of pis-ton effect from hoist equipment, and the study of airflow stability in shaft is the foundation for the stability of ventilation in mine.展开更多
The frictional performance of gaskets is greatly affected by frictional heat in operational mine hoists. Based on frictional mechanism and heat transfer theory, the mathematical model of the temperature field of the P...The frictional performance of gaskets is greatly affected by frictional heat in operational mine hoists. Based on frictional mechanism and heat transfer theory, the mathematical model of the temperature field of the PVC gasket in an operational mine hoist was investigated, a numerical simulation using ANSYS is presented and the distribution of the temperature and heat flux were studied under basic assumptions. The results show that the temperature gradually decreases as the radius of the model increases and the isotherms are arcs of concentric semi-circle. The heat flux is of bilateral symmetry in the model and decreases radially. The theoretical values correspond with the measured values for a short time (τ≤ 100 s) when the steel wire rope slides.展开更多
Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agi...Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agile shell-feeding system, hoist technology was studied. Working principles were discussed and the hydraulic pressure system of the hoist was constructed. The hydraulic pressure cylinder and the accumulator were analyzed and calculated. Finally, PRO/E and ADAMS were used to simulate the hoist and its hydraulic system. It was found that this type of virtual prototype provides a good method to actualize a physical prototype.展开更多
This research investigated the outputting circulation current inhibition characteristic which are controlled by the instantaneous feedback voltage in inverter parallel driving of the mine hoist. We established a trans...This research investigated the outputting circulation current inhibition characteristic which are controlled by the instantaneous feedback voltage in inverter parallel driving of the mine hoist. We established a transfer function of the parallel inverters controlled by the close-loop adjustment of instantaneous voltage feedback. The influence of the parameters of the close-loop feedback circuit to the inhibition effects to the outputting circulation current is observed. After analyzing the circulating current inhibition characteristics, the proportion integration （PI） controller is introduced into the close-loop adjustment by instantaneous voltage feedback. The characteristics equation is gained to determine the PI parameters by drawing the Bode plots. The inhibition effects of the proposed controller are examined by the established simulation model of parallel inverter system. The harmonic distortion rate at the outputting voltage frequency value of 4, 10, 20, 41 and 50 Hz, are all lower than 2.32 % by the instantaneous outputting voltage feedback.展开更多
The hoist bracket links the rescue hoist with the helicopter cabin, and its structure design greatly affects the operation convenience and safety of the hoistman and lifeguard in the rescue process with a helicopter.T...The hoist bracket links the rescue hoist with the helicopter cabin, and its structure design greatly affects the operation convenience and safety of the hoistman and lifeguard in the rescue process with a helicopter.This paper firstly builds the force model of the hoist and bracket, and gives five kinds of typical working conditions as the design ones of the bracket. Then this paper puts forward a design process of the hoist bracket based on the topology optimization and strength analysis with the 3D modeling and finite element analysis. This design process can make the bracket's structure lightweight by achieving the optimal material layout under the conditions of maximizing the static stiffness or minimizing the compliance of the bracket. And this improves the dynamic performance of the helicopter, and reduces the fuel consumption and cost under the strength constraints. Finally,taking the design of the hoist bracket used in a rescue helicopter as an example, this paper illustrates the proposed model and method. The analysis results show that the mass of the hoist bracket decreases by 12.5% while the static stiffness of the hoist bracket is achieved. The optimization design results meet the strength requirements of the hoist.展开更多
Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agi...Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agile shell-feeding system, hoist technology was studied. Working principles were discussed and the hydraulic pressure system of the hoist was constructed. The hydraulic pressure cylinder and the accumulator were analyzed and calculated. Finally, PRO/E and ADAMS were used to simulate the hoist and its hydraulic system. It was found that this type of virtuaU674.7l prototype provides a good method to actualize a physical prototype.展开更多
Serious accidents of mine hoists caused by high-speed sliding between friction lining and wire rope are often seen in coal mines.In order to solve this problem,we analyzed the contact characteristics between friction ...Serious accidents of mine hoists caused by high-speed sliding between friction lining and wire rope are often seen in coal mines.In order to solve this problem,we analyzed the contact characteristics between friction lining and wire rope.Then we carried out a dynamic mechanical analysis(DMA) to explain the change in mechanical properties of the friction lining as function of temperature and load frequency and found that temperature has a stronger effect on the mechanical properties than the frequency.We used multiple regression analysis to obtain the thermoviscoelastic constitutive relations of the friction lining.As well we derived the analytic solution for the thermoviscoelastic contact radius and pressure by combining the theory of viscoelastic contact mechanics with thermoviscoelastic constitutive relations.展开更多
Based on fault diagnosis and fault tolerant technologies, the mine-hoist active fault-tolerant control system (MAFCS) is presented with corresponding strategies,, which includes the fault diagnosis module (FDM), the d...Based on fault diagnosis and fault tolerant technologies, the mine-hoist active fault-tolerant control system (MAFCS) is presented with corresponding strategies,, which includes the fault diagnosis module (FDM), the dynamic library (DL) and the fault-tolerant control module (FCM). When a fault is judged from some sensor by FDM, FCM reconfigure the state of MAFCS by calling the parameters from all sub libraries in DL, in order to ensure the reliabil- ity and safety of mine hoist. The simulating result shows that, MAFCS is of certain intelligence, which can adopt the corresponding control strategies according to different fault modes, even when there are quite difference between the real data and the prior fault modes.展开更多
Mining shovel is a crucial piece of equipment for high-efficiency production in open-pit mining and stands as one of the largest energy consumption sources in mining.However,substantial energy waste occurs during the ...Mining shovel is a crucial piece of equipment for high-efficiency production in open-pit mining and stands as one of the largest energy consumption sources in mining.However,substantial energy waste occurs during the descent of the hoisting system or the deceleration of the slewing platform.To reduce the energy loss,an innovative hydrau-lic-electric hybrid drive system is proposed,in which a hydraulic pump/motor connected with an accumulator is added to assist the electric motor to drive the hoisting system or slewing platform,recycling kinetic and potential energy.The utilization of the kinetic and potential energy reduces the energy loss and installed power of the min-ing shovel.Meanwhile,the reliability of the mining shovel pure electric drive system also can be increased.In this paper,the hydraulic-electric hybrid driving principle is introduced,a small-scale testbed is set up to verify the feasibil-ity of the system,and a co-simulation model of the proposed system is established to clarify the system operation and energy characteristics.The test and simulation results show that,by adopting the proposed system,compared with the traditional purely electric driving system,the peak power and energy consumption of the hoisting electric motor are reduced by 36.7%and 29.7%,respectively.Similarly,the slewing electric motor experiences a significant decrease in peak power by 86.9%and a reduction in energy consumption by 59.4%.The proposed system expands the application area of the hydraulic electric hybrid drive system and provides a reference for its application in over-sized and super heavy equipment.展开更多
The three-bucket jacket foundation is a new type of foundation for offshore wind turbine that has the advantages of fast construction speed and suitability for deep water. The study of the hoisting and launching proce...The three-bucket jacket foundation is a new type of foundation for offshore wind turbine that has the advantages of fast construction speed and suitability for deep water. The study of the hoisting and launching process is of great significance to ensure construction safety in actual projects. In this paper, a new launching technology is proposed that is based on the foundation of the three-bucket jacket for offshore wind turbine. A complete time domain simulation of the launching process of three-bucket jacket foundation is carried out by a theoretical analysis combined with hydrodynamic software Moses. At the same time, the effects of different initial air storage and sea conditions on the motion response of the structure and the hoisting cable tension are studied. The results show that the motion response of the structure is the highest when it is lowered to 1.5 times the bucket height. The natural period of each degree of freedom of the structure increases with the increase of the lowering depth. The structural motion response and the hoisting cable tension vary greatly in the early phases of Stages Ⅰ and Ⅲ, smaller in Stage Ⅱ, and gradually stabilize in the middle and late phases of Stage Ⅲ.展开更多
Dynamic force of BS buffer unit in the enwinding hoisting system is calculated, and the buffer unit is in- stalled and tested. The result shows that this buffer unit is accurate in its regulated braking force and conv...Dynamic force of BS buffer unit in the enwinding hoisting system is calculated, and the buffer unit is in- stalled and tested. The result shows that this buffer unit is accurate in its regulated braking force and convenient in ad- justment and restoration. It can be repeatedly used as a bumper for both over-winding and over-falling without replacing any parts, providing an applicable device for safety operation in coal mining.展开更多
Dynamic running law of the hydraulic driving system decides the hoisting cage velocity curve in a hoisting cycle and is decided by the characteristic of the hydraulic driving system and by the operating speed of hoist...Dynamic running law of the hydraulic driving system decides the hoisting cage velocity curve in a hoisting cycle and is decided by the characteristic of the hydraulic driving system and by the operating speed of hoist driver. The paper studies the dynamic running law of hydraulic driving system, analyses the influence of driver operating speed on the dynamic running characteristic, and points out the reasonable driver operating speed to control the dynamic stress in rope and to reduce the oscillation of rope system.展开更多
Launching vertical shiplift is a type of shiplifts which have the advantages in characteristics of dynamics and statics, safety and simplicity in operation. But their applications are limited as the scales of mechanic...Launching vertical shiplift is a type of shiplifts which have the advantages in characteristics of dynamics and statics, safety and simplicity in operation. But their applications are limited as the scales of mechanical equipments are too large. This paper puts forward the principle of minimization of the equivalent load for the general layout design of launching vertical shiplifts, based on the analysis of the load probability of the main hoists and their key mechanical equipments. The principle aims at determining the optimal weight of counterweight so that the equivalent loads of the main hoists of shiplifls are minimized, and larger ships are permitted to pass through. The theory and method presented in this paper have been applied in the design of the first step and third step shiplifts of the Goupitan Hydro Power Station. This has resulted in the breakthrough of the design and manufacture of launching vertical shiplifts so that the ships with tonnage of 500 t can pass through hydro dams for this type of shiplifts, comparing with the largest launching shiplift in Yantan Hydro Power Station with the 250 t shiplift.展开更多
A6×19 point-contact hoisting cable was used as our research object to examine the progress of corrosion of steel wires in a laboratory,simulating the actual working conditions in a coalmine.An electrochemical met...A6×19 point-contact hoisting cable was used as our research object to examine the progress of corrosion of steel wires in a laboratory,simulating the actual working conditions in a coalmine.An electrochemical method was used to investigate the corrosion behavior of steel wires with different surface treatments of a corrosive acid solution.The results show that anode activation of steel wire mainly occurs during pre-corrosion,where the anode activation process of bare steel wires is the fastest as is their corresponding corrosion speed,while the anode activation process of oil coated steel wires and their corresponding corrosion speed are the lowest.During the intermediate and late immersion periods, a passive film is generated on the surface of steel wires,which are gradually damaged with the passage of time.Local pitting corrosion occurs easily on the surface of steel wires with a high-polarization potential. Suitable equivalent circuits were chosen to fit the electrochemical impedance spectroscopy（EIS）of steel wires over various corrosive times and different surface treatments,which indicate good fitting results. The double electrical layer charge-transfer resistance increases in the sequence：bare steel wire, untreated steel wire and oil coated steel wire and their corrosion resistance decreases in turn,which is consistent with their polarization curves.The oil layer provides a certain protective effect on untreated steel wires,but its effect is not entirely clear.展开更多
基金Supported by the National Basic Research Program(973)(2005CB221506)National Natural Science Foundation of Chongqing(CSTC,2007BA6018)National Key Technology R&D Program(2006ABK03B04)
文摘Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced such as the form conditionand influential factors.Gas and coal dust explosion propagation was researched and thelifting process of coal dust was simulated.When an explosion occurred due to great mixtureof gas and air,the maximum explosion pressure appeared in the neighborhood of theexplosion source point.Before it propagated to the tunnel of the deposited coal dust,themaximum explosion pressure appeared to be in declining trend.Part of the energy waslost in the process of raising the deposited coal dust through a shock wave,so the maximumexplosion pressure was smallest on the foreside of the deposited coal dust sector.On the deposited coal dust sector,the explosion pressure rapidly increased and droppedoff after achieving the largest peak value.Because of coal dust participation in the explosion,the flame velocity rose rapidly on the deposited coal dust and achieved a basic stablevalue;coal dust was ignited to explode by initial laminar flame,and the laminar flametransformed into turbulent flame.The turbulence transformed the flame fold into a funnelshape and the shock wave interacted with the flame,so the combustion rate rose and thepressure wave was further enhanced.The regeneration mechanism between the flamecombustion rate and the aerodynamic flowing structure achieved the final critical state forforming the detonation.
基金Project 06KJD470182 supported by the Jiangsu Educational Natural Science Foundation of china
文摘A new method based on principal component analysis (PCA) and support vector machines (SVMs) is proposed for fault diagnosis of mine hoists. PCA is used to extract the principal features associated with the gearbox. Then, with the irrelevant gearbox variables removed, the remaining gearbox, the hydraulic system and the wire rope parameters were used as input to a multi-class SVM. The SVM is first trained by using the one class-based multi-class optimization algorithm and it is then applied to fault identification. Comparison of various methods showed the PCA-SVM method successfully removed redundancy to solve the dimensionality curse. These results show that the algorithm using the RBF kernel function for the SVM had the best classification properties.
基金Project supported by the Zhejiang Provincial Natural Science Foundation of China(No.LZ16E080001)the National Natural Science Foundation of China(Nos.51578496 and 51878603)。
文摘This paper aims to address the problem of geometric state control of large-segment steel box girders in offshore hoisting during the construction of large-span bridges. First, the geometric state control indexes of a large-segment steel box girder are determined, such as the manufacturing parameters of the top and bottom slabs, the width of the annular joint, and the support position. Second, the geometric state equations and state transfer matrixes of large-segment steel box girders under different conditions are deduced by taking the mileage and elevation of control points as basic state variables. In application of the geometric state transfer method in the construction control of the Hong Kong-Zhuhai-Macao Bridge, the width of the annular joint and the position parameters for the support of the large-segment steel box girder are predicted precisely. Moreover, the manufacturing parameters of the top and bottom slabs of the steel box girders are calculated reliably. The measured values show that the width of the annular joint is basically the same with the difference of less than 2 mm, the eccentricity of bridge support is less than 20 mm, and the elevation error of the bridge deck is within-10 mm to +15 mm, which meets the construction accuracy. Using the geometric state transfer method, the rapid and accurate installation of the Hong Kong-Zhuhai-Macao Bridge has been realized, demonstrating that the precise control of the geometric state of a steel box girder with ectopic installation and multi-state transition can be realized by using the geometric state transfer method.
文摘Using the mass of time-varying length balance rope focused on the hoisting conveyance, the coupling longi- tudinal-transverse model of mine friction hoist was established by using of the Hamilton＇s principle. The modified Galerkin＇s method was used to discretize partial differential Eqs. The mine hoisting system was used to the example to analysis the relation between the load, velocity and transverse vibration of rope. The in situ tests were illustrated to evaluate the proposed mathematical model. The results showed that the modeling method can well represent the transverse vibration of rope.
基金Supported by Natural Science Foundation of China （50474062） and State Administration of Coal Mine Safety of China （04-233）
文摘In order to discover the airflow pattern in mine shaft which outfitted with hoist equipment （HE）, this paper set up the physical model and anatomized the piston-wind caused by hoist equipment, and researched the flow field and velocity field around the hoist equipment during its moving process, and analyzed the airflow around single and couple hoist equipment as well as decisive range of piston effect and additional effect of hoist equipment to ventilation system. Research conclusion indicate that during hoist equipment movement, airflow pattern changes repeatedly because of the influence of pis-ton effect from hoist equipment, and the study of airflow stability in shaft is the foundation for the stability of ventilation in mine.
基金Projects 50225519 supported by the National Outstanding Youth Science Foundation of China0E4458 by the Youth Science Foundation of China Univer-sity of Mining and Technology
文摘The frictional performance of gaskets is greatly affected by frictional heat in operational mine hoists. Based on frictional mechanism and heat transfer theory, the mathematical model of the temperature field of the PVC gasket in an operational mine hoist was investigated, a numerical simulation using ANSYS is presented and the distribution of the temperature and heat flux were studied under basic assumptions. The results show that the temperature gradually decreases as the radius of the model increases and the isotherms are arcs of concentric semi-circle. The heat flux is of bilateral symmetry in the model and decreases radially. The theoretical values correspond with the measured values for a short time (τ≤ 100 s) when the steel wire rope slides.
文摘Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agile shell-feeding system, hoist technology was studied. Working principles were discussed and the hydraulic pressure system of the hoist was constructed. The hydraulic pressure cylinder and the accumulator were analyzed and calculated. Finally, PRO/E and ADAMS were used to simulate the hoist and its hydraulic system. It was found that this type of virtual prototype provides a good method to actualize a physical prototype.
文摘This research investigated the outputting circulation current inhibition characteristic which are controlled by the instantaneous feedback voltage in inverter parallel driving of the mine hoist. We established a transfer function of the parallel inverters controlled by the close-loop adjustment of instantaneous voltage feedback. The influence of the parameters of the close-loop feedback circuit to the inhibition effects to the outputting circulation current is observed. After analyzing the circulating current inhibition characteristics, the proportion integration （PI） controller is introduced into the close-loop adjustment by instantaneous voltage feedback. The characteristics equation is gained to determine the PI parameters by drawing the Bode plots. The inhibition effects of the proposed controller are examined by the established simulation model of parallel inverter system. The harmonic distortion rate at the outputting voltage frequency value of 4, 10, 20, 41 and 50 Hz, are all lower than 2.32 % by the instantaneous outputting voltage feedback.
基金the Science and Technology Project of Ministry of Transport of China(No.2013328225080)the Natural Science Foundation of Liaoning Province of China(No.2015020121)+1 种基金the Research Fund for the Doctoral Program of Higher Education of China(No.20122125120013)the Fundamental Research Funds for the Central Universities of China(Nos.3132016069 and 3132016354)
文摘The hoist bracket links the rescue hoist with the helicopter cabin, and its structure design greatly affects the operation convenience and safety of the hoistman and lifeguard in the rescue process with a helicopter.This paper firstly builds the force model of the hoist and bracket, and gives five kinds of typical working conditions as the design ones of the bracket. Then this paper puts forward a design process of the hoist bracket based on the topology optimization and strength analysis with the 3D modeling and finite element analysis. This design process can make the bracket's structure lightweight by achieving the optimal material layout under the conditions of maximizing the static stiffness or minimizing the compliance of the bracket. And this improves the dynamic performance of the helicopter, and reduces the fuel consumption and cost under the strength constraints. Finally,taking the design of the hoist bracket used in a rescue helicopter as an example, this paper illustrates the proposed model and method. The analysis results show that the mass of the hoist bracket decreases by 12.5% while the static stiffness of the hoist bracket is achieved. The optimization design results meet the strength requirements of the hoist.
文摘Shell-feeding velocity is an important factor affecting naval gun shooting capacity. An agile shell-feeding system was designed to ensure quick implementation of the shell-feeding task. Based on composition of the agile shell-feeding system, hoist technology was studied. Working principles were discussed and the hydraulic pressure system of the hoist was constructed. The hydraulic pressure cylinder and the accumulator were analyzed and calculated. Finally, PRO/E and ADAMS were used to simulate the hoist and its hydraulic system. It was found that this type of virtuaU674.7l prototype provides a good method to actualize a physical prototype.
基金Projects 50875253 supported by the National Natural Science Foundation of China20060290505 by the Research Fund for the Doctoral Program of Higher Education of China+2 种基金107054 by the Key Project of Ministry of Education of ChinaBK2008127 by the Natural Science Foundation of Jiangsu ProvinceCX08B_042Z by the Scientific Innovation Program for Postgraduates in Colleges and Universities of Jiangsu Province
文摘Serious accidents of mine hoists caused by high-speed sliding between friction lining and wire rope are often seen in coal mines.In order to solve this problem,we analyzed the contact characteristics between friction lining and wire rope.Then we carried out a dynamic mechanical analysis(DMA) to explain the change in mechanical properties of the friction lining as function of temperature and load frequency and found that temperature has a stronger effect on the mechanical properties than the frequency.We used multiple regression analysis to obtain the thermoviscoelastic constitutive relations of the friction lining.As well we derived the analytic solution for the thermoviscoelastic contact radius and pressure by combining the theory of viscoelastic contact mechanics with thermoviscoelastic constitutive relations.
文摘Based on fault diagnosis and fault tolerant technologies, the mine-hoist active fault-tolerant control system (MAFCS) is presented with corresponding strategies,, which includes the fault diagnosis module (FDM), the dynamic library (DL) and the fault-tolerant control module (FCM). When a fault is judged from some sensor by FDM, FCM reconfigure the state of MAFCS by calling the parameters from all sub libraries in DL, in order to ensure the reliabil- ity and safety of mine hoist. The simulating result shows that, MAFCS is of certain intelligence, which can adopt the corresponding control strategies according to different fault modes, even when there are quite difference between the real data and the prior fault modes.
基金Supported by National Natural Science Foundation of China(Grant No.U1910211)National Key Research and Development Program of China(Grant No.2021YFB2011903).
文摘Mining shovel is a crucial piece of equipment for high-efficiency production in open-pit mining and stands as one of the largest energy consumption sources in mining.However,substantial energy waste occurs during the descent of the hoisting system or the deceleration of the slewing platform.To reduce the energy loss,an innovative hydrau-lic-electric hybrid drive system is proposed,in which a hydraulic pump/motor connected with an accumulator is added to assist the electric motor to drive the hoisting system or slewing platform,recycling kinetic and potential energy.The utilization of the kinetic and potential energy reduces the energy loss and installed power of the min-ing shovel.Meanwhile,the reliability of the mining shovel pure electric drive system also can be increased.In this paper,the hydraulic-electric hybrid driving principle is introduced,a small-scale testbed is set up to verify the feasibil-ity of the system,and a co-simulation model of the proposed system is established to clarify the system operation and energy characteristics.The test and simulation results show that,by adopting the proposed system,compared with the traditional purely electric driving system,the peak power and energy consumption of the hoisting electric motor are reduced by 36.7%and 29.7%,respectively.Similarly,the slewing electric motor experiences a significant decrease in peak power by 86.9%and a reduction in energy consumption by 59.4%.The proposed system expands the application area of the hydraulic electric hybrid drive system and provides a reference for its application in over-sized and super heavy equipment.
基金financially supported by the National Natural Science Foundation of China (Grant No.52171274)。
文摘The three-bucket jacket foundation is a new type of foundation for offshore wind turbine that has the advantages of fast construction speed and suitability for deep water. The study of the hoisting and launching process is of great significance to ensure construction safety in actual projects. In this paper, a new launching technology is proposed that is based on the foundation of the three-bucket jacket for offshore wind turbine. A complete time domain simulation of the launching process of three-bucket jacket foundation is carried out by a theoretical analysis combined with hydrodynamic software Moses. At the same time, the effects of different initial air storage and sea conditions on the motion response of the structure and the hoisting cable tension are studied. The results show that the motion response of the structure is the highest when it is lowered to 1.5 times the bucket height. The natural period of each degree of freedom of the structure increases with the increase of the lowering depth. The structural motion response and the hoisting cable tension vary greatly in the early phases of Stages Ⅰ and Ⅲ, smaller in Stage Ⅱ, and gradually stabilize in the middle and late phases of Stage Ⅲ.
文摘Dynamic force of BS buffer unit in the enwinding hoisting system is calculated, and the buffer unit is in- stalled and tested. The result shows that this buffer unit is accurate in its regulated braking force and convenient in ad- justment and restoration. It can be repeatedly used as a bumper for both over-winding and over-falling without replacing any parts, providing an applicable device for safety operation in coal mining.
文摘Dynamic running law of the hydraulic driving system decides the hoisting cage velocity curve in a hoisting cycle and is decided by the characteristic of the hydraulic driving system and by the operating speed of hoist driver. The paper studies the dynamic running law of hydraulic driving system, analyses the influence of driver operating speed on the dynamic running characteristic, and points out the reasonable driver operating speed to control the dynamic stress in rope and to reduce the oscillation of rope system.
文摘Launching vertical shiplift is a type of shiplifts which have the advantages in characteristics of dynamics and statics, safety and simplicity in operation. But their applications are limited as the scales of mechanical equipments are too large. This paper puts forward the principle of minimization of the equivalent load for the general layout design of launching vertical shiplifts, based on the analysis of the load probability of the main hoists and their key mechanical equipments. The principle aims at determining the optimal weight of counterweight so that the equivalent loads of the main hoists of shiplifls are minimized, and larger ships are permitted to pass through. The theory and method presented in this paper have been applied in the design of the first step and third step shiplifts of the Goupitan Hydro Power Station. This has resulted in the breakthrough of the design and manufacture of launching vertical shiplifts so that the ships with tonnage of 500 t can pass through hydro dams for this type of shiplifts, comparing with the largest launching shiplift in Yantan Hydro Power Station with the 250 t shiplift.
基金supported by the National Natural Science Foundation of China(No.50875252)the Program for New Century Excellent Talents in University(No.NCET-06-0479).
文摘A6×19 point-contact hoisting cable was used as our research object to examine the progress of corrosion of steel wires in a laboratory,simulating the actual working conditions in a coalmine.An electrochemical method was used to investigate the corrosion behavior of steel wires with different surface treatments of a corrosive acid solution.The results show that anode activation of steel wire mainly occurs during pre-corrosion,where the anode activation process of bare steel wires is the fastest as is their corresponding corrosion speed,while the anode activation process of oil coated steel wires and their corresponding corrosion speed are the lowest.During the intermediate and late immersion periods, a passive film is generated on the surface of steel wires,which are gradually damaged with the passage of time.Local pitting corrosion occurs easily on the surface of steel wires with a high-polarization potential. Suitable equivalent circuits were chosen to fit the electrochemical impedance spectroscopy（EIS）of steel wires over various corrosive times and different surface treatments,which indicate good fitting results. The double electrical layer charge-transfer resistance increases in the sequence：bare steel wire, untreated steel wire and oil coated steel wire and their corrosion resistance decreases in turn,which is consistent with their polarization curves.The oil layer provides a certain protective effect on untreated steel wires,but its effect is not entirely clear.
