Under certain accident conditions in particle accelerators,high-power beam irradiation may damage vacuum pipes,magnets,and other key equipment.Therefore,machine protection for high-power accelerators is critical to en...Under certain accident conditions in particle accelerators,high-power beam irradiation may damage vacuum pipes,magnets,and other key equipment.Therefore,machine protection for high-power accelerators is critical to ensure safe operation.It is important to study radiation damage to materials to support the design and operation of machine protection systems.In the shock-wave regime,a pronounced hydrodynamic tunneling effect occurs within materials.The traditional one-way coupling simulation method results in substantial errors in this regime.Therefore,a bidirectional iterative coupling simulation method was developed.This method enables the bidirectional coupling of the Monte Carlo code FLUKA and the thermodynamic program Ansys-Autodyn.Density changes are monitored during the simulations,and the updated density is promptly fed back to FLUKA.The program remodels the target with the new density distribution to calculate the new energy deposition distribution,which is then returned to Autodyn for subsequent simulations.This iterative process continues until the entire beam has completed the energy deposition process.Compared to existing methods,this automated method significantly improves the efficiency of the coupled simulations and reduces the possibility of human error.The HRMT-12 beam irradiation experiment at CERN was used for a benchmark study,and simulations were conducted and compared using different equations of state.The results demonstrate the efficiency and accuracy of this simulation method.Compared to complex and costly beam irradiation experiments,this approach is expected to provide fast and cost-effective scientific guidance for the machine protection of high-power accelerators.Considering the severe consequences of the hydrodynamic tunneling effect,machine protection components such as beam collimators,absorbers,and dump blocks should adopt low-density materials to reduce the energy deposition density.Beam dilution may be required in beam dumping systems to avoid target damage.This method can be applied to the redundancy design of such beam dumping systems.展开更多
The types of dopants lead to distinctive microstructural evolution behavior and physical properties in materials.In this study,the effect of stoichiometric and non-stoichiometric Mn modification,namely Pb(Mn_(1/3) Nb_...The types of dopants lead to distinctive microstructural evolution behavior and physical properties in materials.In this study,the effect of stoichiometric and non-stoichiometric Mn modification,namely Pb(Mn_(1/3) Nb_(2/3))O_(3)(PMnN)and MnO_(2),on the microstructure and properties of Pb(Yb_(1/2) Nb_(1/2))O_(3)-PbZrO_(3)-PbTiO_(3)(PYN-PZT)piezoelectric ceramics are systematically investigated.It was found that stoichiometric PMnN modification inhibits the grain growth while non-stoichiometric MnO_(2) modification promotes it,and thus the former yields stronger high-power characteristics(higher internal bias field Ei and larger mechanical quality factor Q_(m))than the latter.Specifically,with an equivalent amount of Mn modifica-tion(2 mol%),PMnN and MnO_(2) modification PYN-PZT ceramics exhibit significantly different values for average grain size(1.21μm vs.14.12μm),Ei(8.5 kV/cm vs.5 kV/cm),and Qm(2376 vs.1134).To further evaluate high-power performance,the vibration velocity v of these two modified PYN-PZT under high driving conditions was measured.Under an AC electric field of 3.5 V/mm,the PYN-PZT+6PMnN ceram-ics exhibit a v of up to 0.95 m s^(−1),larger than both MnO2-doped PYN-PZT(0.72 m s^(−1))and unmodified PYN-PZT ceramics(0.1 m s^(−1)),and far outperformance than both PZT-4 and PZT-8 ceramics.Furthermore,to elucidate the origin of the exceptional high-power performance of PMnN-modified PYN-PZT,we per-formed phase-field simulations revealing a pinning effect of the grain boundary on domain wall motion.Consequently,the small grain size(high grain boundary density)in PMnN-modified PYN-PZT exhibits a strong pinning effect,resulting in a large Q_(m) and outstanding high-power performance.展开更多
Lead magnesium niobate-lead titanate(PMN-PT)piezoelectric single crystals are widely utilized due to their outstanding performance,with varying compositions significantly impacting their properties.While application o...Lead magnesium niobate-lead titanate(PMN-PT)piezoelectric single crystals are widely utilized due to their outstanding performance,with varying compositions significantly impacting their properties.While application of PMN-PT in high-power settings is rapidly evolving,material parameters are typically tested under low signal conditions(1 V),and effects of different PT(PbTiO_(3))contents on the performance of PMN-PT single crystals under high-power conditions remain unclear.This study developed a comprehensive high-power testing platform using the constant voltage method to evaluate performance of PMN-PT single crystals with different PT contents under high-power voltage stimulation.Using crystals sized at 10 mm×3 mm×0.5 mm as an example,this research explored changes in material parameters.The results exhibit that while trend of the parameter changes under high-power excitation was consistent across different PT contents,degree of the change varied significantly.For instance,a PMN-PT single crystal with 26%(in mol)PT content exhibited a 25%increase in the piezoelectric coefficient d_(31),a 13%increase in the elastic compliance coefficient s_(11)^(E),a 17%increase in the electromechanical coupling coefficient k_(31),and a 73%decrease in the mechanical quality factor Q_(m) when the power reached 7.90 W.As the PT content increased,the PMN-PT materials became more susceptible to temperature influences,significantly reducing the power tolerance and more readily reaching the depolarization temperatures.This led to loss of piezoelectric performance.Based on these findings,a clearer understanding of impact of PT content on performance of PMN-PT single crystals under high-power applications has been established,providing reliable data to support design of sensors or transducers using PMN-PT as the sensitive element.展开更多
High-power laser technology is widely used in manufacturing processing,medical diagnosis,and treatment,and is one of the important fields of strategic high-tech competition in China at the moment.In the context of ind...High-power laser technology is widely used in manufacturing processing,medical diagnosis,and treatment,and is one of the important fields of strategic high-tech competition in China at the moment.In the context of industrial upgrading,high-power laser technology plays an important role in leading the development of the manufacturing industry and industrial intelligence.Based on this,this paper carries out research on high-power laser technology and industry,summarizes the basic principle and classification of high-power laser technology,analyzes the current status of high-power laser technology industry,points out the opportunities and challenges faced by the industry development,puts forward suggestions to promote the development of high-power laser technology industry,and to provide an effective reference for the application and development of high-power laser technology.展开更多
The Na_(4)Fe_(3)(PO_(4))_(2)P_(2)O_(7)(NFPP)has considered as a very attractive cathode material for Na-ion batteries mainly due to its cheap price and high security.Its low electron transfer rate is usually improved ...The Na_(4)Fe_(3)(PO_(4))_(2)P_(2)O_(7)(NFPP)has considered as a very attractive cathode material for Na-ion batteries mainly due to its cheap price and high security.Its low electron transfer rate is usually improved by coating a layer of hard carbon,which however exhibits a low graphitization degree because of the relatively low NFPP synthesis temperature(~500℃).In this study,a highly-conductive hybrid carbon has been employed to accelerate redox reaction kinetics of NFPP by modulating electronic structure for achieving high-power Na-ion batteries.The hybrid carbon is derived from the mixed polyethylene glycol(PEG)and glucose,in which the low ether bond energy(~340 kJ mol^(-1))of PEG facilitates the free radical generation during pyrolysis with high graphitization degree while glucose improves the uniformity of the c arbon coating.As a result,the optimized cathode exhibits a very high reversible capacity of 90.8 mAh g^(-1)at 20C within 2.0-4.0 V with 85.3%capacity retention after 10,000 cycles,highlighting huge application potentials in two-wheeled electric vehicles,backup energy storage,and so forth.展开更多
The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust pe...The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust performance.Current research focuses on its operational principles,control strategies,and behavior under various load conditions.Key considerations include component selection,thermal management,and EMI/EMC optimization.This topology finds applications across renewable energy systems,industrial equipment,telecommunications,and electric vehicle charging infrastructures.Comparative analyses with alternative topologies and cost-benefit evaluations are also addressed.Future developments are expected to emphasize the integration of wide-bandgap devices and advancements in digital control techniques to further enhance efficiency and system performance.展开更多
This research focuses on solving the fault detection and health monitoring of high-power thyristor converter.In terms of the critical role of thyristor converter in nuclear fusion system,a method based on long short-t...This research focuses on solving the fault detection and health monitoring of high-power thyristor converter.In terms of the critical role of thyristor converter in nuclear fusion system,a method based on long short-term memory(LSTM)neural network model is proposed to monitor the operational state of the converter and accurately detect faults as they occur.By sampling and processing a large number of thyristor converter operation data,the LSTM model is trained to identify and detect abnormal state,and the power supply health status is monitored.Compared with traditional methods,LSTM model shows higher accuracy and abnormal state detection ability.The experimental results show that this method can effectively improve the reliability and safety of the thyristor converter,and provide a strong guarantee for the stable operation of the nuclear fusion reactor.展开更多
Nano-scale chemical inhomogeneity in surface oxide films formed on a V-and N-containing martensite stainless steel and tempering heating induced changes are investigated by a combination of synchrotron-based hard X-ra...Nano-scale chemical inhomogeneity in surface oxide films formed on a V-and N-containing martensite stainless steel and tempering heating induced changes are investigated by a combination of synchrotron-based hard X-ray Photoelectron emission spectroscopy(HAXPES)and microscopy(HAXPEEM)as well as microscopic X-ray absorption spectroscopy(μ-XAS)techniques.The results reveal the inhomogeneity in the oxide films on the micron-sized Cr_(2)N-and VN-type particles,while the inhomogeneity on the martensite matrix phase exists due to localised formation of nano-sized tempering nitride particles at 600℃.The oxide film formed on Cr_(2)N-type particles is rich in Cr_(2)O_(3) compared with that on the martensite matrix and VN-type particles.With the increase of tempering temperature,Cr_(2)O_(3) formation is faster for the oxidation of Cr in the martensite matrix than the oxidation of Cr nitride-rich particles.展开更多
Microscopy imaging is fundamental in analyzing bacterial morphology and dynamics,offering critical insights into bacterial physiology and pathogenicity.Image segmentation techniques enable quantitative analysis of bac...Microscopy imaging is fundamental in analyzing bacterial morphology and dynamics,offering critical insights into bacterial physiology and pathogenicity.Image segmentation techniques enable quantitative analysis of bacterial structures,facilitating precise measurement of morphological variations and population behaviors at single-cell resolution.This paper reviews advancements in bacterial image segmentation,emphasizing the shift from traditional thresholding and watershed methods to deep learning-driven approaches.Convolutional neural networks(CNNs),U-Net architectures,and three-dimensional(3D)frameworks excel at segmenting dense biofilms and resolving antibiotic-induced morphological changes.These methods combine automated feature extraction with physics-informed postprocessing.Despite progress,challenges persist in computational efficiency,cross-species generalizability,and integration with multimodal experimental workflows.Future progress will depend on improving model robustness across species and imaging modalities,integrating multimodal data for phenotype-function mapping,and developing standard pipelines that link computational tools with clinical diagnostics.These innovations will expand microbial phenotyping beyond structural analysis,enabling deeper insights into bacterial physiology and ecological interactions.展开更多
Desulfurization of CaO–Al_(2)O_(3) particles in molten steel was observed in situ using high-temperature confocal scanning laser microscopy.The effects of the aluminum and silicon contents of molten steel on desulfur...Desulfurization of CaO–Al_(2)O_(3) particles in molten steel was observed in situ using high-temperature confocal scanning laser microscopy.The effects of the aluminum and silicon contents of molten steel on desulfurization were analyzed.When the total aluminum content in the steel increased from 6 to 1100 ppm,the CaS content in CaO–Al_(2)O_(3) particles increased from 2.1wt%to 84.84wt%after the reaction for 90 s.Furthermore,when the silicon content in the steel increased from 0.01wt%to 2.20wt%,the CaS content in CaO–Al_(2)O_(3) particles increased from 1.53wt%to 79.01wt%after the reaction for 90 s.This indicates that the increase in the aluminum and silicon contents of the steel promoted the desulfurization of CaO–Al_(2)O_(3) particles.A kinetic model was established to predict the CaO–Al_(2)O_(3) particles composition,and the diffusion coefficient of sulfur in CaO–Al_(2)O_(3) particles was 9.375×10^(−10)m^(2)·s^(−1) at 1600℃,which provided a new method for the calculation of diffusion coefficient.展开更多
Classification of plume and spatter images was studied to evaluate the welding stability. A high-speed camera was used to capture the instantaneous images of plume and spatters during high power disk laser welding. Ch...Classification of plume and spatter images was studied to evaluate the welding stability. A high-speed camera was used to capture the instantaneous images of plume and spatters during high power disk laser welding. Characteristic parameters such as the area and number of spatters, the average grayscale of a spatter image, the entropy of a spatter grayscale image, the coordinate ratio of the plume centroid and the welding point, the polar coordinates of the plume centroid were defined and extracted. Karhunen-Loeve transform method was used to change the seven characteristics into three primary characteristics to reduce the dimensions. Also, K-nearest neighbor method was used to classify the plume and spatter images into two categories such as good and poor welding quality. The results show that plume and spatter have a close relationship with the welding stability, and two categories could be recognized effectively using K-nearest neighbor method based on Karhunen-Loeve transform.展开更多
By Using （scanning） transmission electron microscopy, localized-corrosion morphology variations of the AA7055 AIZn（Cu）Mg alloy with different thermal processes and their underlying microscopic causes were investig...By Using （scanning） transmission electron microscopy, localized-corrosion morphology variations of the AA7055 AIZn（Cu）Mg alloy with different thermal processes and their underlying microscopic causes were investigated systematically. Our study shows that the corrosion resistance of the nanoscale precipitates varies with their structure type and Cu-content. Just like the Al-matrix, the early-stage precipitates are corrosion resistant, as compared with the ηp/η-precipitates without high Cu-content. With a high Cu-content, however, the η-precipitates become most corrosion resistant among all phases involved. Hence, tailoring the precipitate microstructure and chemistry though thermal processes may change the overall corrosion morphology and improve corrosion resistance property of the alloy.展开更多
Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain met...Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain method and the panicle tracing method, such an algorithm is self-consistent and accurate since the interaction between electromagnetic fields and particles is properly modeled. In the time domain aspect, the generation of multipactor can be easily visualized, which makes it possible to gain a deeper insight into the physical mechanism of this effect. In addition to the classic secondary electron emission model, the measured practical secondary electron yield is used, which increases the accuracy of the algorithm. In order to validate the method, the impedance transformer and ridge waveguide filter are studied. By analyzing the evolution of the secondaries obtained by our method, multipactor thresholds of these components are estimated, which show good agreement with the experimental results. Furthermore, the most sensitive positions where multipactor occurs are determined from the phase focusing phenomenon, which is very meaningful for multipactor analysis and design.展开更多
To improve the characteristics of a diamond-like carbon （DLC） film, Ti-containing amorphous hydrogenated carbon thin films were deposited on sus304 stainless steel substrates by high-power plasma-sputtering with tit...To improve the characteristics of a diamond-like carbon （DLC） film, Ti-containing amorphous hydrogenated carbon thin films were deposited on sus304 stainless steel substrates by high-power plasma-sputtering with titanium metal as the solid plasma source in a mixed ArC2H2 atmosphere. The films were fabricated to obtain a multilayered structure of Ti/TiC/DLC gradient for improving adhesion and reducing residual stress. The effects of substrate bias and target-substrate distance on the films＇ properties were studied by glow discharge spectroscope, X-ray diffractometer, Raman spectroscope, nanoindenter, and a pin-on-disk tribometer. The results indicate that the films possess superior adhesive strength and toughness.展开更多
A two-dimensional model of the silicon NPN monolithic composite transistor is established for the first time by utilizing the semiconductor device simulator, Sentaurus-TCAD. By analyzing the internal distributions of ...A two-dimensional model of the silicon NPN monolithic composite transistor is established for the first time by utilizing the semiconductor device simulator, Sentaurus-TCAD. By analyzing the internal distributions of electric field, current density, and temperature of the device, a detailed investigation on the damage process and mechanism induced by high-power microwaves （HPM） is performed. The results indicate that the temperature elevation occurs in the negative half-period and the temperature drop process is in the positive half-period under the HPM injection from the output port. The damage point is located near the edge of the base-emitter junction of T2, while with the input injection it exists between the base and the emitter of T2. Comparing these two kinds of injection, the input injection is more likely to damage the device than the output injection. The dependences of the damage energy threshold and the damage power threshold causing the device failure on the pulse-width are obtained, and the formulas obtained have the same form as the experimental equations, which demonstrates that more power is required to destroy the device if the pulse-width is shorter. Furthermore, the simulation result in this paper has a good coincidence with the experimental result.展开更多
Thermal management is one of the key technologies for high-power Light emitting diode(LED)entering into the general illuminating field.Successful thermal management depends on optimal packaging structure and selected ...Thermal management is one of the key technologies for high-power Light emitting diode(LED)entering into the general illuminating field.Successful thermal management depends on optimal packaging structure and selected packaging materials.In this paper,the aluminum is employed as a substrate of LED,3×3 array chips are placed on the substrate,heat dissipation performance is simulated using finite element analysis(FEA)software,analyzed are the influences on the temperature of the chip with different convection coefficient,and optical properties are simulated using optical analysis software.The results show that the packaging structure can not only effectually improve the thermal performance of high-power LED array but also increase the light extraction efficiency.展开更多
Microwave pre-treatment is considered as a promising technique for alleviating cutter wear. This paper introduces a high-power microwave-induced fracturing system for hard rock. The test system consists of a high-powe...Microwave pre-treatment is considered as a promising technique for alleviating cutter wear. This paper introduces a high-power microwave-induced fracturing system for hard rock. The test system consists of a high-power microwave subsystem (100 kW), a true triaxial testing machine, a dynamic monitoring subsystem, and an electromagnetic shielding subsystem. It can realize rapid microwave-induced fracturing, intelligent tuning of impedance, dynamic feedback under strong microwave fields, and active control of microwave parameters by addressing the following issues: the instability and insecurity of the system, the discharge breakdown between coaxial lines during high-power microwave output, and a lack of feedback of rock-microwave response. In this study, microwave-induced surface and borehole fracturing tests under true triaxial stress were carried out. Experimental comparisons imply that high-power microwave irradiation can reduce the fracturing time of hard rock and that the fracture range (160 mm) of a 915-MHz microwave source is about three times that of 2.45 GHz. After microwave-induced borehole fracturing, many tensile cracks occur on the rock surface and in the borehole: the maximum reduction of the P-wave velocity is 12.8%. The test results show that a high-power microwave source of 915 MHz is more conducive to assisting mechanical rock breaking and destressing. The system can promote the development of microwave-assisted rock breaking equipment.展开更多
To reduce the energy demand and operation cost for circular electron positron collider(CEPC), the high efficiency klystrons are being developed at Institute of High Energy Physics, Chinese Academy of Sciences. A 800-k...To reduce the energy demand and operation cost for circular electron positron collider(CEPC), the high efficiency klystrons are being developed at Institute of High Energy Physics, Chinese Academy of Sciences. A 800-k W continuous wave(CW) klystron operating at frequency of 650-MHz has been designed. The results of beam–wave interaction simulation with several different codes are presented. The efficiency is optimized to be 65% with a second harmonic cavity in three-dimensional(3D) particle-in-cell code CST. The effect of cavity frequency error and mismatch load on efficiency of klystron have been investigated. The design and cold test of reentrant cavities are described, which meet the requirements of RF section design. So far, the manufacturing and high-power test of the first klystron prototype have been completed.When the gun operated at DC voltage of 80 k V and current of 15.4 A, the klystron peak power reached 804 k W with output efficiency of about 65.3% at 40% duty cycle. The 1-d B bandwidth is ±0.8 MHZ. Due to the crack of ceramic window, the CW power achieved about 700 kW. The high-power test results are in good agreement with 3D simulation.展开更多
We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the...We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the measurement of the pulse-front distortion of the pulse from a complex multi-pass amplification system, which exists in almost all high-power laser systems, and obtain the irregular pulse-front distribution. The method presented does not need any reference light or assumption about the pulse-front distribution, and has an accuracy of several femtoseconds.展开更多
We report high-power single-spatial-mode type-I GaSb-based tapered lasers fabricated on the InGaSb/AlGaAsSb material system. A straight ridge and three different tapered waveguide structures with varying flare angles ...We report high-power single-spatial-mode type-I GaSb-based tapered lasers fabricated on the InGaSb/AlGaAsSb material system. A straight ridge and three different tapered waveguide structures with varying flare angles are fabricated to optimize the output power and spatial-mode performance. The best devices exhibit single-spatial-mode operation with room-temperature output power up to 350？mW in continuous-wave mode at an emission wavelength around 2.0？μm with a very small far-field lateral divergence angle, which is beyond state of the art in terms of single-spatial-mode output power.展开更多
基金supported by the National Natural Science Foundation of China(No.12275196)。
文摘Under certain accident conditions in particle accelerators,high-power beam irradiation may damage vacuum pipes,magnets,and other key equipment.Therefore,machine protection for high-power accelerators is critical to ensure safe operation.It is important to study radiation damage to materials to support the design and operation of machine protection systems.In the shock-wave regime,a pronounced hydrodynamic tunneling effect occurs within materials.The traditional one-way coupling simulation method results in substantial errors in this regime.Therefore,a bidirectional iterative coupling simulation method was developed.This method enables the bidirectional coupling of the Monte Carlo code FLUKA and the thermodynamic program Ansys-Autodyn.Density changes are monitored during the simulations,and the updated density is promptly fed back to FLUKA.The program remodels the target with the new density distribution to calculate the new energy deposition distribution,which is then returned to Autodyn for subsequent simulations.This iterative process continues until the entire beam has completed the energy deposition process.Compared to existing methods,this automated method significantly improves the efficiency of the coupled simulations and reduces the possibility of human error.The HRMT-12 beam irradiation experiment at CERN was used for a benchmark study,and simulations were conducted and compared using different equations of state.The results demonstrate the efficiency and accuracy of this simulation method.Compared to complex and costly beam irradiation experiments,this approach is expected to provide fast and cost-effective scientific guidance for the machine protection of high-power accelerators.Considering the severe consequences of the hydrodynamic tunneling effect,machine protection components such as beam collimators,absorbers,and dump blocks should adopt low-density materials to reduce the energy deposition density.Beam dilution may be required in beam dumping systems to avoid target damage.This method can be applied to the redundancy design of such beam dumping systems.
基金supported by the National Key Research and Development Program of China(No.2023YFF0720700)the National Natural Science Foundation of China(Nos.52032010 and 52272120)the Central Government Funds of Guiding Local Scientific and Technological Development for Sichuan Province(No.2022ZYD0018).
文摘The types of dopants lead to distinctive microstructural evolution behavior and physical properties in materials.In this study,the effect of stoichiometric and non-stoichiometric Mn modification,namely Pb(Mn_(1/3) Nb_(2/3))O_(3)(PMnN)and MnO_(2),on the microstructure and properties of Pb(Yb_(1/2) Nb_(1/2))O_(3)-PbZrO_(3)-PbTiO_(3)(PYN-PZT)piezoelectric ceramics are systematically investigated.It was found that stoichiometric PMnN modification inhibits the grain growth while non-stoichiometric MnO_(2) modification promotes it,and thus the former yields stronger high-power characteristics(higher internal bias field Ei and larger mechanical quality factor Q_(m))than the latter.Specifically,with an equivalent amount of Mn modifica-tion(2 mol%),PMnN and MnO_(2) modification PYN-PZT ceramics exhibit significantly different values for average grain size(1.21μm vs.14.12μm),Ei(8.5 kV/cm vs.5 kV/cm),and Qm(2376 vs.1134).To further evaluate high-power performance,the vibration velocity v of these two modified PYN-PZT under high driving conditions was measured.Under an AC electric field of 3.5 V/mm,the PYN-PZT+6PMnN ceram-ics exhibit a v of up to 0.95 m s^(−1),larger than both MnO2-doped PYN-PZT(0.72 m s^(−1))and unmodified PYN-PZT ceramics(0.1 m s^(−1)),and far outperformance than both PZT-4 and PZT-8 ceramics.Furthermore,to elucidate the origin of the exceptional high-power performance of PMnN-modified PYN-PZT,we per-formed phase-field simulations revealing a pinning effect of the grain boundary on domain wall motion.Consequently,the small grain size(high grain boundary density)in PMnN-modified PYN-PZT exhibits a strong pinning effect,resulting in a large Q_(m) and outstanding high-power performance.
基金Research and Development Project on Voltage Sensors by China Southern Power Grid Digital Research Institute(210000KK52220017)。
文摘Lead magnesium niobate-lead titanate(PMN-PT)piezoelectric single crystals are widely utilized due to their outstanding performance,with varying compositions significantly impacting their properties.While application of PMN-PT in high-power settings is rapidly evolving,material parameters are typically tested under low signal conditions(1 V),and effects of different PT(PbTiO_(3))contents on the performance of PMN-PT single crystals under high-power conditions remain unclear.This study developed a comprehensive high-power testing platform using the constant voltage method to evaluate performance of PMN-PT single crystals with different PT contents under high-power voltage stimulation.Using crystals sized at 10 mm×3 mm×0.5 mm as an example,this research explored changes in material parameters.The results exhibit that while trend of the parameter changes under high-power excitation was consistent across different PT contents,degree of the change varied significantly.For instance,a PMN-PT single crystal with 26%(in mol)PT content exhibited a 25%increase in the piezoelectric coefficient d_(31),a 13%increase in the elastic compliance coefficient s_(11)^(E),a 17%increase in the electromechanical coupling coefficient k_(31),and a 73%decrease in the mechanical quality factor Q_(m) when the power reached 7.90 W.As the PT content increased,the PMN-PT materials became more susceptible to temperature influences,significantly reducing the power tolerance and more readily reaching the depolarization temperatures.This led to loss of piezoelectric performance.Based on these findings,a clearer understanding of impact of PT content on performance of PMN-PT single crystals under high-power applications has been established,providing reliable data to support design of sensors or transducers using PMN-PT as the sensitive element.
文摘High-power laser technology is widely used in manufacturing processing,medical diagnosis,and treatment,and is one of the important fields of strategic high-tech competition in China at the moment.In the context of industrial upgrading,high-power laser technology plays an important role in leading the development of the manufacturing industry and industrial intelligence.Based on this,this paper carries out research on high-power laser technology and industry,summarizes the basic principle and classification of high-power laser technology,analyzes the current status of high-power laser technology industry,points out the opportunities and challenges faced by the industry development,puts forward suggestions to promote the development of high-power laser technology industry,and to provide an effective reference for the application and development of high-power laser technology.
基金financially supported by the National Natural Science Foundation of China(Nos.U22A20429 and 22308103)the Program for Shanghai Pilot Program for Basic Research(No.22TQ1400100-13)the Fundamental Research Funds for the Central Universities
文摘The Na_(4)Fe_(3)(PO_(4))_(2)P_(2)O_(7)(NFPP)has considered as a very attractive cathode material for Na-ion batteries mainly due to its cheap price and high security.Its low electron transfer rate is usually improved by coating a layer of hard carbon,which however exhibits a low graphitization degree because of the relatively low NFPP synthesis temperature(~500℃).In this study,a highly-conductive hybrid carbon has been employed to accelerate redox reaction kinetics of NFPP by modulating electronic structure for achieving high-power Na-ion batteries.The hybrid carbon is derived from the mixed polyethylene glycol(PEG)and glucose,in which the low ether bond energy(~340 kJ mol^(-1))of PEG facilitates the free radical generation during pyrolysis with high graphitization degree while glucose improves the uniformity of the c arbon coating.As a result,the optimized cathode exhibits a very high reversible capacity of 90.8 mAh g^(-1)at 20C within 2.0-4.0 V with 85.3%capacity retention after 10,000 cycles,highlighting huge application potentials in two-wheeled electric vehicles,backup energy storage,and so forth.
文摘The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust performance.Current research focuses on its operational principles,control strategies,and behavior under various load conditions.Key considerations include component selection,thermal management,and EMI/EMC optimization.This topology finds applications across renewable energy systems,industrial equipment,telecommunications,and electric vehicle charging infrastructures.Comparative analyses with alternative topologies and cost-benefit evaluations are also addressed.Future developments are expected to emphasize the integration of wide-bandgap devices and advancements in digital control techniques to further enhance efficiency and system performance.
基金supported by the Open Fund of Magnetic Confinement Fusion Laboratory of Anhui Province(No.2024AMF04003)the Natural Science Foundation of Anhui Province(No.228085ME142)Comprehensive Research Facility for Fusion Technology(No.20180000527301001228)。
文摘This research focuses on solving the fault detection and health monitoring of high-power thyristor converter.In terms of the critical role of thyristor converter in nuclear fusion system,a method based on long short-term memory(LSTM)neural network model is proposed to monitor the operational state of the converter and accurately detect faults as they occur.By sampling and processing a large number of thyristor converter operation data,the LSTM model is trained to identify and detect abnormal state,and the power supply health status is monitored.Compared with traditional methods,LSTM model shows higher accuracy and abnormal state detection ability.The experimental results show that this method can effectively improve the reliability and safety of the thyristor converter,and provide a strong guarantee for the stable operation of the nuclear fusion reactor.
基金supported by the Vinnova(project number 2020-03778)supported by the Swedish Research Council(Vetenskapsradet,project number 2021-04157).
文摘Nano-scale chemical inhomogeneity in surface oxide films formed on a V-and N-containing martensite stainless steel and tempering heating induced changes are investigated by a combination of synchrotron-based hard X-ray Photoelectron emission spectroscopy(HAXPES)and microscopy(HAXPEEM)as well as microscopic X-ray absorption spectroscopy(μ-XAS)techniques.The results reveal the inhomogeneity in the oxide films on the micron-sized Cr_(2)N-and VN-type particles,while the inhomogeneity on the martensite matrix phase exists due to localised formation of nano-sized tempering nitride particles at 600℃.The oxide film formed on Cr_(2)N-type particles is rich in Cr_(2)O_(3) compared with that on the martensite matrix and VN-type particles.With the increase of tempering temperature,Cr_(2)O_(3) formation is faster for the oxidation of Cr in the martensite matrix than the oxidation of Cr nitride-rich particles.
基金financially supported by the Open Project Program of Wuhan National Laboratory for Optoelectronics(No.2022WNLOKF009)the National Natural Science Foundation of China(No.62475216)+2 种基金the Key Research and Development Program of Shaanxi(No.2024GH-ZDXM-37)the Fujian Provincial Natural Science Foundation of China(No.2024J01060)the Startup Program of XMU,and the Fundamental Research Funds for the Central Universities.
文摘Microscopy imaging is fundamental in analyzing bacterial morphology and dynamics,offering critical insights into bacterial physiology and pathogenicity.Image segmentation techniques enable quantitative analysis of bacterial structures,facilitating precise measurement of morphological variations and population behaviors at single-cell resolution.This paper reviews advancements in bacterial image segmentation,emphasizing the shift from traditional thresholding and watershed methods to deep learning-driven approaches.Convolutional neural networks(CNNs),U-Net architectures,and three-dimensional(3D)frameworks excel at segmenting dense biofilms and resolving antibiotic-induced morphological changes.These methods combine automated feature extraction with physics-informed postprocessing.Despite progress,challenges persist in computational efficiency,cross-species generalizability,and integration with multimodal experimental workflows.Future progress will depend on improving model robustness across species and imaging modalities,integrating multimodal data for phenotype-function mapping,and developing standard pipelines that link computational tools with clinical diagnostics.These innovations will expand microbial phenotyping beyond structural analysis,enabling deeper insights into bacterial physiology and ecological interactions.
基金supported by the National Key R&D Program of China(No.2023YFB3709900)the National Nature Science Foundation of China(No.U22A20171)+1 种基金the China Baowu Low Carbon Metallurgy Innovation Foundation(No.BWLCF202315)the High Steel Center(HSC)at North China University of Technology and University of Science and Technology Beijing,China.
文摘Desulfurization of CaO–Al_(2)O_(3) particles in molten steel was observed in situ using high-temperature confocal scanning laser microscopy.The effects of the aluminum and silicon contents of molten steel on desulfurization were analyzed.When the total aluminum content in the steel increased from 6 to 1100 ppm,the CaS content in CaO–Al_(2)O_(3) particles increased from 2.1wt%to 84.84wt%after the reaction for 90 s.Furthermore,when the silicon content in the steel increased from 0.01wt%to 2.20wt%,the CaS content in CaO–Al_(2)O_(3) particles increased from 1.53wt%to 79.01wt%after the reaction for 90 s.This indicates that the increase in the aluminum and silicon contents of the steel promoted the desulfurization of CaO–Al_(2)O_(3) particles.A kinetic model was established to predict the CaO–Al_(2)O_(3) particles composition,and the diffusion coefficient of sulfur in CaO–Al_(2)O_(3) particles was 9.375×10^(−10)m^(2)·s^(−1) at 1600℃,which provided a new method for the calculation of diffusion coefficient.
基金Project (51175095) supported by the National Natural Science Foundation of ChinaProjects (10251009001000001,9151009001000020) supported by the Natural Science Foundation of Guangdong Province,ChinaProject (20104420110001) supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘Classification of plume and spatter images was studied to evaluate the welding stability. A high-speed camera was used to capture the instantaneous images of plume and spatters during high power disk laser welding. Characteristic parameters such as the area and number of spatters, the average grayscale of a spatter image, the entropy of a spatter grayscale image, the coordinate ratio of the plume centroid and the welding point, the polar coordinates of the plume centroid were defined and extracted. Karhunen-Loeve transform method was used to change the seven characteristics into three primary characteristics to reduce the dimensions. Also, K-nearest neighbor method was used to classify the plume and spatter images into two categories such as good and poor welding quality. The results show that plume and spatter have a close relationship with the welding stability, and two categories could be recognized effectively using K-nearest neighbor method based on Karhunen-Loeve transform.
基金financially supported by the National Natural Science Foundation of China(Nos.51501059,51471067,51501060,and 11427806)the National Key Research and Development Program of China(No.2016YFB0300801)
文摘By Using （scanning） transmission electron microscopy, localized-corrosion morphology variations of the AA7055 AIZn（Cu）Mg alloy with different thermal processes and their underlying microscopic causes were investigated systematically. Our study shows that the corrosion resistance of the nanoscale precipitates varies with their structure type and Cu-content. Just like the Al-matrix, the early-stage precipitates are corrosion resistant, as compared with the ηp/η-precipitates without high Cu-content. With a high Cu-content, however, the η-precipitates become most corrosion resistant among all phases involved. Hence, tailoring the precipitate microstructure and chemistry though thermal processes may change the overall corrosion morphology and improve corrosion resistance property of the alloy.
基金Project supported by the National Key Laboratory Foundation,China(Grant No.9140C530103110C5301)
文摘Based on the particle-in-cell technology and the secondary electron emission theory, a three-dimensional simulation method for multipactor is presented in this paper. By combining the finite difference time domain method and the panicle tracing method, such an algorithm is self-consistent and accurate since the interaction between electromagnetic fields and particles is properly modeled. In the time domain aspect, the generation of multipactor can be easily visualized, which makes it possible to gain a deeper insight into the physical mechanism of this effect. In addition to the classic secondary electron emission model, the measured practical secondary electron yield is used, which increases the accuracy of the algorithm. In order to validate the method, the impedance transformer and ridge waveguide filter are studied. By analyzing the evolution of the secondaries obtained by our method, multipactor thresholds of these components are estimated, which show good agreement with the experimental results. Furthermore, the most sensitive positions where multipactor occurs are determined from the phase focusing phenomenon, which is very meaningful for multipactor analysis and design.
文摘To improve the characteristics of a diamond-like carbon （DLC） film, Ti-containing amorphous hydrogenated carbon thin films were deposited on sus304 stainless steel substrates by high-power plasma-sputtering with titanium metal as the solid plasma source in a mixed ArC2H2 atmosphere. The films were fabricated to obtain a multilayered structure of Ti/TiC/DLC gradient for improving adhesion and reducing residual stress. The effects of substrate bias and target-substrate distance on the films＇ properties were studied by glow discharge spectroscope, X-ray diffractometer, Raman spectroscope, nanoindenter, and a pin-on-disk tribometer. The results indicate that the films possess superior adhesive strength and toughness.
文摘A two-dimensional model of the silicon NPN monolithic composite transistor is established for the first time by utilizing the semiconductor device simulator, Sentaurus-TCAD. By analyzing the internal distributions of electric field, current density, and temperature of the device, a detailed investigation on the damage process and mechanism induced by high-power microwaves （HPM） is performed. The results indicate that the temperature elevation occurs in the negative half-period and the temperature drop process is in the positive half-period under the HPM injection from the output port. The damage point is located near the edge of the base-emitter junction of T2, while with the input injection it exists between the base and the emitter of T2. Comparing these two kinds of injection, the input injection is more likely to damage the device than the output injection. The dependences of the damage energy threshold and the damage power threshold causing the device failure on the pulse-width are obtained, and the formulas obtained have the same form as the experimental equations, which demonstrates that more power is required to destroy the device if the pulse-width is shorter. Furthermore, the simulation result in this paper has a good coincidence with the experimental result.
基金Key Scientific and Technological Research Projects of Henan Province(072102240027)Dr Foundation of Henan Polytechnic University(648602)Postgraduate Degree Thesis Innovation Foundation of Henan Polytechnic University(644005)
文摘Thermal management is one of the key technologies for high-power Light emitting diode(LED)entering into the general illuminating field.Successful thermal management depends on optimal packaging structure and selected packaging materials.In this paper,the aluminum is employed as a substrate of LED,3×3 array chips are placed on the substrate,heat dissipation performance is simulated using finite element analysis(FEA)software,analyzed are the influences on the temperature of the chip with different convection coefficient,and optical properties are simulated using optical analysis software.The results show that the packaging structure can not only effectually improve the thermal performance of high-power LED array but also increase the light extraction efficiency.
基金support from the Na-tional Natural Science Foundation of China(Grant No.41827806)the liaoning Revitalization Talent Program of China(Grant No.XLYCYSZX1902).
文摘Microwave pre-treatment is considered as a promising technique for alleviating cutter wear. This paper introduces a high-power microwave-induced fracturing system for hard rock. The test system consists of a high-power microwave subsystem (100 kW), a true triaxial testing machine, a dynamic monitoring subsystem, and an electromagnetic shielding subsystem. It can realize rapid microwave-induced fracturing, intelligent tuning of impedance, dynamic feedback under strong microwave fields, and active control of microwave parameters by addressing the following issues: the instability and insecurity of the system, the discharge breakdown between coaxial lines during high-power microwave output, and a lack of feedback of rock-microwave response. In this study, microwave-induced surface and borehole fracturing tests under true triaxial stress were carried out. Experimental comparisons imply that high-power microwave irradiation can reduce the fracturing time of hard rock and that the fracture range (160 mm) of a 915-MHz microwave source is about three times that of 2.45 GHz. After microwave-induced borehole fracturing, many tensile cracks occur on the rock surface and in the borehole: the maximum reduction of the P-wave velocity is 12.8%. The test results show that a high-power microwave source of 915 MHz is more conducive to assisting mechanical rock breaking and destressing. The system can promote the development of microwave-assisted rock breaking equipment.
基金Project supported by Yifang Wang’s Science Studio of the Ten Thousand Talents Project。
文摘To reduce the energy demand and operation cost for circular electron positron collider(CEPC), the high efficiency klystrons are being developed at Institute of High Energy Physics, Chinese Academy of Sciences. A 800-k W continuous wave(CW) klystron operating at frequency of 650-MHz has been designed. The results of beam–wave interaction simulation with several different codes are presented. The efficiency is optimized to be 65% with a second harmonic cavity in three-dimensional(3D) particle-in-cell code CST. The effect of cavity frequency error and mismatch load on efficiency of klystron have been investigated. The design and cold test of reentrant cavities are described, which meet the requirements of RF section design. So far, the manufacturing and high-power test of the first klystron prototype have been completed.When the gun operated at DC voltage of 80 k V and current of 15.4 A, the klystron peak power reached 804 k W with output efficiency of about 65.3% at 40% duty cycle. The 1-d B bandwidth is ±0.8 MHZ. Due to the crack of ceramic window, the CW power achieved about 700 kW. The high-power test results are in good agreement with 3D simulation.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 10904132 and 11074225)the National Defense Science Technology Foundation of State Key Laboratory of High Temperature and Density Plasma Physics,China (Grant No. 9140C680604110C6805)
文摘We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the measurement of the pulse-front distortion of the pulse from a complex multi-pass amplification system, which exists in almost all high-power laser systems, and obtain the irregular pulse-front distribution. The method presented does not need any reference light or assumption about the pulse-front distribution, and has an accuracy of several femtoseconds.
基金Supported by the National Basic Research Program of China under Grant Nos 2014CB643903 and 2013CB932904the National Natural Science Foundation of China under Grant Nos 61435012 and 61290303the Strategic Priority Research Program(B) of the Chinese Academy of Sciences under Grant No XDB01010200
文摘We report high-power single-spatial-mode type-I GaSb-based tapered lasers fabricated on the InGaSb/AlGaAsSb material system. A straight ridge and three different tapered waveguide structures with varying flare angles are fabricated to optimize the output power and spatial-mode performance. The best devices exhibit single-spatial-mode operation with room-temperature output power up to 350？mW in continuous-wave mode at an emission wavelength around 2.0？μm with a very small far-field lateral divergence angle, which is beyond state of the art in terms of single-spatial-mode output power.
