High-performance concrete （HPC） has specific performance advantages over conventional concrete in strength and durability. HPC mixtures are usually produced with water/binder mass ratios （mW/mB） in the range of 0....High-performance concrete （HPC） has specific performance advantages over conventional concrete in strength and durability. HPC mixtures are usually produced with water/binder mass ratios （mW/mB） in the range of 0.2-0.4, so volume changes of concrete as a result of drying, chemical reactions, and temperature change cannot be avoided. For these reasons, shrinkage and cracking are frequent phenomena. It is necessary to add some types of admixture for reduction of shrinkage and cracking of HPC. This study used a shrinkage-reducing admixture （SRA） for that purpose. Concrete was prepared with two different mW/mB （0.22 and 0.40） and four different mass fractions of SRA to binder （w（SRA） = 0%, 1%, 2%, and 4%）. The mineral admixtures used for concrete mixes were： 25% fly ash （FA） and 25% slag by mass of binder for the mixture with mW/mB = 0.40, and 15% silica fume （SF） and 25% FA for the mixture with mW/mB = 0.22. Tests were conducted on 24 prismatic specimens, and shrinkage strains were measured through 120 days of drying. Compressive strength, splitting strength, and static modulus of elasticity were also determined. The results show that the SRA effectively reduces some mechanical properties of HPC. The reductions in compressive strength, splitting tensile strength, and elastic modulus of the concrete were 7%-24%, 9%-19%, and 5%-12%, respectively, after 90 days, compared to concrete mixtures without SRA. SRA can also help reduce drying shrinkage of concrete. The shrinkage strains of HPC with SRA were only as high as 41% of the average free shrinkage of concrete without SRA after 120 days of drying.展开更多
The improvements of the mechanical properties, including bulk density of fresh mixtures, elastic modulus, and compressive strengths of four high-performance concrete mixtures, made with the addition of fly ash, refine...The improvements of the mechanical properties, including bulk density of fresh mixtures, elastic modulus, and compressive strengths of four high-performance concrete mixtures, made with the addition of fly ash, refined ground blast - furnace microslag (microslag) and silica fume are studied. The concrete mixtures were determined based on the dispersion testing results. The study indicates that the elastic modulus at 28 and 91 days, and compressive strengths of the concretes are improved a lot when fly ash and microslag by 25 percent by weight of cement are added into the mixtures individually. The improvement is especially evident when silica fume by 5 percent and fly ash by 25 percent by weight of cement are added together into the mixture, while the fresh concrete mixture keeps a good workability. Through the analysis of chemically combined water ratios of the four mixtures at various hydration ages, it is found that the addition of all these mineral mixtures are beneficial to the hydration process, especially, at later stages, which might be one of the reasons for the improvement of mechanical properties. (Author abstract) 4 Refs.展开更多
On January 30th,2008 BASF’s Construction Chemicals Business was commissioned as the supplier of a high-per-formance admixture,to facilitate the concrete construction process for the upcoming luxury Li Xing Hotel in S...On January 30th,2008 BASF’s Construction Chemicals Business was commissioned as the supplier of a high-per-formance admixture,to facilitate the concrete construction process for the upcoming luxury Li Xing Hotel in Shanghai’s Xin Tian Di landmark.It also supports the high-rise pump-展开更多
Four typical admixtures,polycarboxylate superplasticiser(PCE),tartaric acid(TA),sorbitol and polyacrylamide(PAM),were selected to systematically investigate their regulatory mechanisms on the formation of ettringite t...Four typical admixtures,polycarboxylate superplasticiser(PCE),tartaric acid(TA),sorbitol and polyacrylamide(PAM),were selected to systematically investigate their regulatory mechanisms on the formation of ettringite through Fourier transform infrared spectroscopy,X-ray diffraction,particle size analysis and nucleation kinetic model.The experimental results indicate that the admixtures alter the formation of ettringite through physical adsorption,complexation and solution viscosity modulation without changing its chemical structure.Low concentrations of PCE inhibit size growth by forming an adsorption layer on the surface of ettringite,whereas high concentrations of PCE alter the size change of ettringite by modulating the distribution of ionic concentrations.TA significantly reduces the size of ettringite by complexing Ca^(2+).Sorbitol and PAM promote the local growth of ettringite at low concentrations,leading to larger sizes.But at high concentrations,the size growth of ettringite is inhibited due to the increase in viscosity or the enhancement of complexation.Matlab nucleation kinetic modelling further shows that the addition of admixtures enhances the initial nucleation during ettringite synthesis,with values ranging from 14.45%to 114.25%.However,the subsequent nucleation rate of ettringite is significantly affected,decreasing by 12.79%to 71.74%.The results provide a theoretical basis for the design of ettringite materials and the optimisation of the application of admixtures.展开更多
This study investigated the factors contributing to intravenous admixture preparation errors(IAPEs)within Pharmacy Intravenous Admixture Services(PIVAS).A retrospective analysis was conducted on IAPEs documented in th...This study investigated the factors contributing to intravenous admixture preparation errors(IAPEs)within Pharmacy Intravenous Admixture Services(PIVAS).A retrospective analysis was conducted on IAPEs documented in the PIVAS unit of a large multi-specialty hospital in China,which houses over 2000 beds,covering the period from January 1,2015 to December 31,2022.Drug preparation records were examined using a generalized linear mixed model(GLMM)to identify both univariate and multivariate factors associated with IAPE occurrences.A total of 824 IAPE cases were recorded during the study period,yielding an overall error rate of 0.018%.Univariate analysis identified drug categories(general drugs,anti-infective drugs,and antineoplastic drugs),preparation time(workdays),and years of work experience as significant determinants(P<0.05).Multivariate analysis further confirmed that drug categories(general and antineoplastic drugs),preparation time(workdays),and work experience remained statistically significant predictors of IAPE incidence(P<0.05).IAPEs in PIVAS were influenced by multiple factors,predominantly those related to personnel and drug characteristics.Targeted interventions,informed by multivariate analysis,are essential to mitigating these errors and enhancing medication safety.展开更多
An evaluation method for self-healing capacity was designed,which includes the control of initial cracks and subsequent permeability testing.This method was employed to evaluate the self-healing behavior of mortars in...An evaluation method for self-healing capacity was designed,which includes the control of initial cracks and subsequent permeability testing.This method was employed to evaluate the self-healing behavior of mortars incorporating crystalline admixtures(CAs)under various conditions,including water immersion,limewater soaking,and wet-dry cycles,with varying CA dosages and crack widths.The experimental results indicate that cement possesses inherently self-healing capability.Limewater environments inhibits healing compared with water immersion;however,wet-dry cycles enhance the effectiveness of higher CA dosages.Increasing the CA content can not improve healing performance,and wide cracks(0.3 mm)substantially reduce the intrinsic self-healing potential of cement.展开更多
In this paper,the effects of four different mineral ginseng materials on the mechanical properties of mortar were studied,and the results showed that high territory,fly ash,and silica fume had an inhibitory effect on ...In this paper,the effects of four different mineral ginseng materials on the mechanical properties of mortar were studied,and the results showed that high territory,fly ash,and silica fume had an inhibitory effect on the drying shrinkage of mortar,and mineral powder increased the drying shrinkage of mortar.The high territory in the mineral admixture has the best effect on the inhibition of mortar drying shrinkage.The compressive strength and flexural strength of the mortar can be improved by adding a certain amount of mineral admixture,which increases the compressive strength by about 20%-40%and the flexural strength by about 20%-30%compared with the control group,and the improvement effect difference between different components is not large.展开更多
[Objectives]To establish an HPLC method for the quantitative determination of multiple phenolic acid components in Tetracera asiatica medicinal material,providing a basis for establishing its quality standards.[Method...[Objectives]To establish an HPLC method for the quantitative determination of multiple phenolic acid components in Tetracera asiatica medicinal material,providing a basis for establishing its quality standards.[Methods]An Inertsil ODS-C 18 column(250 mm×4.6 mm,5μm)was used.The mobile phase consisted of acetonitrile-0.2% phosphoric acid solution(10:90).The flow rate was 1.0 mL/min.The detection wavelength was 274 nm.The column temperature was 25℃.The injection volume was 10μL.The content of three components,gallic acid,protocatechuic acid,and protocatechualdehyde,was determined in 13 batches of T.asiatica.[Results]Gallic acid showed good linearity within the range of 0.020-6.400μg/mL,protocatechuic acid within 0.201-6.432μg/mL,and protocatechualdehyde within 0.202-6.464μg/mL(r>0.9990).The average recovery rates ranged from 98.61%to 101.17%,with RSD s between 1.21%and 2.69%.[Conclusions]The quantitative determination method established in this study is simple and feasible,and can provide a basis for the quality evaluation of T.asiatica.展开更多
Covalent organic frameworks(COFs)have demonstrated great potential in chromatographic separation because of unique structure and superior performance.Herein,single-crystal three-dimensional(3D)COFs with regular morpho...Covalent organic frameworks(COFs)have demonstrated great potential in chromatographic separation because of unique structure and superior performance.Herein,single-crystal three-dimensional(3D)COFs with regular morphology,good monodispersity and high specific surface area,were used as a stationary phase for high-performance liquid chromatography(HPLC).The single-crystal 3D COFs packed column not only exhibits high efficiency in separating hydrophobic molecules involving substituted benzenes,halogenated benzenes,halogenated nitrobenzenes,aromatic amines,aromatic hydrocarbons(PAHs)and phthalate esters(PAEs),but also achieves baseline separation of acenaphthene and acenaphthylene with similar physical and chemical properties as well as environmental pollutants,which cannot be quickly separated on commercial C18 column and a polycrystalline 3D COFs packed column.Especially,the column efficiency of 17303-24255 plates/m was obtained for PAEs,and the resolution values for acenaphthene and acenaphthylene,and carbamazepine(CBZ)and carbamazepine-10,11-epoxide(CBZEP)were 1.7and 2.2,respectively.This successful application not only confirmed the great potential of the singlecrystal 3D COFs in HPLC separation of the organic molecules,but also facilitates the application of COFs in separation science.展开更多
Compared to subtractive manufacturing and casting,3D printing(additive manufacturing)offers advantages,such as the rapid production of complex structures,reduced material waste,and environmental friendliness.Direct in...Compared to subtractive manufacturing and casting,3D printing(additive manufacturing)offers advantages,such as the rapid production of complex structures,reduced material waste,and environmental friendliness.Direct ink writing(DIW)is one of the most popular 3D printing techniques owing to its ability to print multiple materials simultaneously and its high compatibility with printing inks.However,DIW presents significant challenges,particularly in the printing of high-performance polymers.The main challenges are as follows:1.The rigid structures and reaction kinetics of high-performance polymers make developing new inks difficult.2.The limited types of available high-performance polymers underscore the need for new DIW-suitable materials.3.Layer-by-layer stacking weakens interlayer bonding,affecting the mechanical properties of the printed product.4.The accuracy and speed of DIW printing are insufficient for large-scale manufacturing.After introducing the topic,the requirements for DIW printing inks are first reviewed,emphasizing the importance of thixotropic agents.Then,research progress regarding DIW printing of high-performance polymers is comprehensively reviewed according to the requirements of different polymer inks.Additionally,the applications of these materials across various fields are summarized.Finally,the challenges in DIW printing of high-performance polymers,along with corresponding solutions and future development prospects,are discussed in detail.展开更多
As electronic devices continue to evolve toward higher power densities,faster speeds,and smaller form factors,the demand for high-performance electronic packaging materials has become increasingly critical.These mater...As electronic devices continue to evolve toward higher power densities,faster speeds,and smaller form factors,the demand for high-performance electronic packaging materials has become increasingly critical.These materials serve as the physical and functional interface between semiconductor components and their operating environment,impacting the overall reliability,thermal management,mechanical protection,and electrical performance of modern electronic systems.This study investigates the development,formulation,and performance evaluation of advanced packaging materials,focusing on polymer-based composites,metal and ceramic matrix systems,and nanomaterial-enhanced formulations.A comprehensive analysis of key performance metrics-including thermal conductivity,electrical insulation,mechanical robustness,and environmental resistance-is presented,alongside strategies for material optimization through interface engineering and processing innovations.Furthermore,the study explores cutting-edge integration technologies such as 3D packaging compatibility,low-temperature co-firing,and high-density interconnects.The findings provide critical insights into the structure-property-processing relationships that define the effectiveness of next-generation packaging materials and offer a roadmap for material selection and system integration in high-reliability electronic applications.展开更多
In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomogra...In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomography）is employed to quantitatively analyze the initial defects in four series of highperformance concrete （HPC）specimens with additions of different mineral admixtures. The nigh-resolution 3D images of microstructures and filtered defects are reconstructed by micro- CT software. The size distribution and volume fractions of initial defects are analyzed based on 3D and 2D micro-CT images. The analysis results are verified by experimental results of watersuction tests. The results show that the additions of mineral admixtures in concrete as cementitious materials greatly change the geometrical properties of the microstructures and the spatial features of defects by physical-chemistry actions of these mineral admixtures. This is the major cause of the differences between the mechanical behaviors of HPC with and without mineral admixtures when the water-to-binder ratio and the size distribution of aggregates are constant.展开更多
In the present study, we aimed to analyze the irrational medical orders and evaluate the effect of pharmacy intervention on pharmacy intravenous admixture services of outpatient and emergency departments in our hospit...In the present study, we aimed to analyze the irrational medical orders and evaluate the effect of pharmacy intervention on pharmacy intravenous admixture services of outpatient and emergency departments in our hospital. The irrational medical orders of PIVAS at the outpatient and emergency departments were retrospectively analyzed in Jun. 2015. We strengthened the pharmacy intervention on irrational medical orders since July 2015. All the cases were selected by systematic sampling method. Cased studied in Jun. 2015 served as the control group, whereas those studied in Jan. 2016 served as the intervention group. The irrational rate and the irrational number of daily average were compared between the control group and intervention group. The common type of irrational outpatient and emergency intravenous orders mainly included irrational use of solvents, irrational dosing interval and inappropriate compatibility of drugs. The irrational rate was reduced from 17.4% to 3.3% （P〈0.01）, and the irrational number of daily average was decreased from 5.23 to 1.00 （P〈0.01）. Pharmacy intervention can reduce the irrational rate of medical orders in our hospital, which is of great significance to promote rational drug use and improve medical quality.展开更多
A simple, sensible and reliable HPLC-DAD fingerprint analysis method for the raw materials of Oxytropisfalcata and Oxytropis chiliophylla, both of which were used as ＂Er-Da-Xia＂ in Tibetan medicines, was developed a...A simple, sensible and reliable HPLC-DAD fingerprint analysis method for the raw materials of Oxytropisfalcata and Oxytropis chiliophylla, both of which were used as ＂Er-Da-Xia＂ in Tibetan medicines, was developed and then subsequently applied to analyze samples collected from different locations or times. 19 common fingerprint peaks for O. falcata, 24 for O. chiliophylla, and 11 for the two herbs were designated respectively, including 7 identified characteristic peaks existing in both herbs and 1 uniquely presenting in O. chiliophylla. Although there were some slight differences in the chemicals of O. falcata and O. chiliophylla, the main components of both herbs were consistent generally. The results provided scientific basis, at least from the chemical point of view, for the reasonablity of two herbs being used as the same drug in Tibetan medicines and for the necessary of further investigation on their detailed chemical and pharmacological differences.展开更多
The expansion and micro-cracks of the mortar with composite mineral admixtures （fly ash, zeolite and slag） due to the alkali-silica reaction （ASR） are studied. Results show that composite mineral admixtures cannot...The expansion and micro-cracks of the mortar with composite mineral admixtures （fly ash, zeolite and slag） due to the alkali-silica reaction （ASR） are studied. Results show that composite mineral admixtures cannot absolutely diminish the ASR of mortar bars with the low-alkali cement and a highly reactive aggregate. But the expansion rate and the deleterious expansion of the mortar bar are mostly reduced with increasing composite mineral admixture. The influence of mineral admixtures on the fluidity of the paste and the strength of the mortar is also studied.展开更多
The crude and processed Paeoniae Radix Alba-Atractylodis Macrocephalae Rhizoma herbal pairs, originated from Bai-zhu-shao-yao-san, are used to treat different diseases clinically. In order to evaluate the crude and pr...The crude and processed Paeoniae Radix Alba-Atractylodis Macrocephalae Rhizoma herbal pairs, originated from Bai-zhu-shao-yao-san, are used to treat different diseases clinically. In order to evaluate the crude and processed Paeoniae Radix-Atractylodis Macrocephalae Rhizoma herbal pairs, a simple, easy, and sensitive high-performance liquid chromatography coupled with diode array detectors was developed for simultaneous determination of nine bioactive components in the herbal pairs. The calibration curve exhibited good linearity（r2≥0.9992）. The LODs and LOQs were ≤7.30 and 11.53 μg/m L, respectively. The intra-, inter-day and repeatability RSD values of the nine compounds were less than 3.86%, 2.71%, and 4.29%, respectively. The RSD stability values were less than 3.64%. The recovery of the method was in the range of 96.70%–102.10%, with RSD values less than 3.52%. The developed method can be applied to the intrinsic quality control of crude and processed Paeoniae Radix-Atractylodis Macrocephalae Rhizoma herbal pairs.展开更多
The rice husk ash （ RHA） and silica （ Si02） nanoparticles are prepared from rice husk charcoal （RHC） by the methods of ventilated calcining and chemical precipitation, respectively, to remove the residual carbon...The rice husk ash （ RHA） and silica （ Si02） nanoparticles are prepared from rice husk charcoal （RHC） by the methods of ventilated calcining and chemical precipitation, respectively, to remove the residual carbon which is harmful to cement composites. The structures and morphologies of these products are investigated by the Fourier transform infrared spectroscopy, X-ray diffraction, scanning/ transmission electron microscopy and N2 adsorption- desorption analyzer. The results show that the as-produced RHA and Si02 nanoparticles exist in amorphous phase without residual carbon, and exhibit porous structures with specific surface areas of 170.19 and 248. 67 m2 /g , respectively. The micro particles of RHA are aggregated by numerous loosely packed Si02 gel particles with the diameter of 50 to 100 nm. The Si02 nanoparticles are well dispersed with the average size of about 30 nm. Both the RHA and Si02 nanoparticles can significantly reduce the conductivity of saturated Ca（OH）2 solution and increase the early strength of the cement composites. They also exhibit high pozzolanic activity, indicating that they can be used as ecological nano mineral admixtures.展开更多
The peroxyoxalate chemiluminescence(CL)detection of fatty acids in human se- rum combined with high-performance liquid chromatography (HPLC)is described.Some fatty acids in serum were extracted with a 1 :1(v/v)mixture...The peroxyoxalate chemiluminescence(CL)detection of fatty acids in human se- rum combined with high-performance liquid chromatography (HPLC)is described.Some fatty acids in serum were extracted with a 1 :1(v/v)mixture of chloroform-n-heptane.2-(4-Hydrazinocarbonyl- phenyl)-4,5-diphenylimidazole (HCPI) was used as a fluorescent labelling reagent of the fatty acids. The labelling reaction was carried out at 30℃ for 1 h at pH 6.5 and the resulting reaction mixture was sudjected to HPLC. The labelled fatty acid C_(17)(P-C_(17))was used as the internal standard. The la- belled fatty acids C_(16) and C_(18) were separated within 18 min on an ODS-8OTM column (150 mm× 6 mm ID,5μm,Tosoh Japan).The calibrlation curves of fatty acids from the spiked control serum were Y_1=-0.003 7 + 0.0028X_1,r=0.994 for FA C_( 16) and Y_2=0.00 1 2 + 0.00098X_2,r=0.999 for FA C_( 18),respectively.The average recoveries of facids from the spiked contrl serum were 107.2%(n=8,RSD=4.3%)for FA C_(16) and 97.35%(n=8, RSD=4.0%)for FA C_(18),respectively.The lower detection limits of fatty acids after reaction were 12μmol per 20μl injection for FA C_(16) and 18 μmol per 20μl injection for FA C_(18),respectively(signal to noise ratio, S/N=2).The HPLC/CL method was applied to the determination of FA C_(16) and FA C_(18) in normal human serum and the results showed that the concentrations of fatty acids in normal human serum were 0.134 ± 0.009 μ mol/ml serum(n=5) for FA C_(16) and 0.052±0.028 μmol/ml serum(n=5)for FA C_(18),respectively.展开更多
Rhizoma Polygoni Bistortae has been widely used as an important medicinal herb in the Far East for a few thousand years, and it has gained more recognition in the last few decades. In the present study, we used a high...Rhizoma Polygoni Bistortae has been widely used as an important medicinal herb in the Far East for a few thousand years, and it has gained more recognition in the last few decades. In the present study, we used a high-performance capillary electrophoresis （HPCE） method for determination of the gallic acid （GA） in Quanshen （QS） pieces. The analysis of GA in QS pieces was successfully achieved in less than 6 min by capillary electrophoresis with UV detection at a wavelength of 290 nm. The background electrolyte was 20 mmol/L sodium borate solution （pH 9.00）. The separation was performed in an uncoated fused-silica capillary （52 cm^50 lam） with an effective length of 40 cm, and the applied voltage was 20 kV. Sample solutions were injected for l0 s at an atmospheric pressure of 5 KPa. The result showed good resolution and precision （the intra-day RSD was 0.37%）. The calibration curves of the standard solutions were linear in the range of 0.22-2.25 mg/mL, with correlation coefficients greater than 0.9990. The recovery of the method ranged from 100.6% to 107.9%, and the average recovery of GA was 105.9% with an RSD of 3.63%. HPCE is a powerful technology, and it is the first time to successfully apply such a method for the determination of GA in the traditional Chinese medicine.展开更多
We quantitatively determined four nucleosides, including cytidine, uridine, guanosine, and adenosine, in Carthamus tinctorius L. and Safflower injection. Separation was performed on a Zorbax Eclipse XDB-18 column usin...We quantitatively determined four nucleosides, including cytidine, uridine, guanosine, and adenosine, in Carthamus tinctorius L. and Safflower injection. Separation was performed on a Zorbax Eclipse XDB-18 column using a gradient elution with mobile phases of 0.05% trifluoroacetic acid （TFA） aqueous solution （A） and methanol （B）. The assay was carried out at a flow rate of 1 mL/min at 25 ℃ with detection at 260 nm. Cytidine, uridine, adenosine and guanosine showed good linearity in the ranges of4.02-503μg/mL （r2= 0.9998）, 9.38-1407 μg/mL （rz = 0.9999）, 80.6-8060μg/mL （r2 = 0.9999） and 2.10---630μg/mL （r2 = 0.9987） with average recoveries of 97.2%, 94.5%, 98.6% and 108.6%, respectively. The contents of cytidine, uridine, adenosine and guanosine in different Carthamus tinctorius L. and Safflower injection were significantly different. This is the first report on the quantitative determination of nucleosides in Carthamus tinctorius L. and Safflower injection.展开更多
文摘High-performance concrete （HPC） has specific performance advantages over conventional concrete in strength and durability. HPC mixtures are usually produced with water/binder mass ratios （mW/mB） in the range of 0.2-0.4, so volume changes of concrete as a result of drying, chemical reactions, and temperature change cannot be avoided. For these reasons, shrinkage and cracking are frequent phenomena. It is necessary to add some types of admixture for reduction of shrinkage and cracking of HPC. This study used a shrinkage-reducing admixture （SRA） for that purpose. Concrete was prepared with two different mW/mB （0.22 and 0.40） and four different mass fractions of SRA to binder （w（SRA） = 0%, 1%, 2%, and 4%）. The mineral admixtures used for concrete mixes were： 25% fly ash （FA） and 25% slag by mass of binder for the mixture with mW/mB = 0.40, and 15% silica fume （SF） and 25% FA for the mixture with mW/mB = 0.22. Tests were conducted on 24 prismatic specimens, and shrinkage strains were measured through 120 days of drying. Compressive strength, splitting strength, and static modulus of elasticity were also determined. The results show that the SRA effectively reduces some mechanical properties of HPC. The reductions in compressive strength, splitting tensile strength, and elastic modulus of the concrete were 7%-24%, 9%-19%, and 5%-12%, respectively, after 90 days, compared to concrete mixtures without SRA. SRA can also help reduce drying shrinkage of concrete. The shrinkage strains of HPC with SRA were only as high as 41% of the average free shrinkage of concrete without SRA after 120 days of drying.
基金Funded by the Reasearch Grant Council to Hongkong University of Science and Technology (Grant No. R1G94195. EG07).
文摘The improvements of the mechanical properties, including bulk density of fresh mixtures, elastic modulus, and compressive strengths of four high-performance concrete mixtures, made with the addition of fly ash, refined ground blast - furnace microslag (microslag) and silica fume are studied. The concrete mixtures were determined based on the dispersion testing results. The study indicates that the elastic modulus at 28 and 91 days, and compressive strengths of the concretes are improved a lot when fly ash and microslag by 25 percent by weight of cement are added into the mixtures individually. The improvement is especially evident when silica fume by 5 percent and fly ash by 25 percent by weight of cement are added together into the mixture, while the fresh concrete mixture keeps a good workability. Through the analysis of chemically combined water ratios of the four mixtures at various hydration ages, it is found that the addition of all these mineral mixtures are beneficial to the hydration process, especially, at later stages, which might be one of the reasons for the improvement of mechanical properties. (Author abstract) 4 Refs.
文摘On January 30th,2008 BASF’s Construction Chemicals Business was commissioned as the supplier of a high-per-formance admixture,to facilitate the concrete construction process for the upcoming luxury Li Xing Hotel in Shanghai’s Xin Tian Di landmark.It also supports the high-rise pump-
基金Funded by the National Natural Science Foundation of China(Nos.51578412,51878479,52078372,and 52478272)the International Science and Technology Cooperation Project of the Key R&D Program of Science and Technology Innovation Yongjiang 2035(No.2024H023)。
文摘Four typical admixtures,polycarboxylate superplasticiser(PCE),tartaric acid(TA),sorbitol and polyacrylamide(PAM),were selected to systematically investigate their regulatory mechanisms on the formation of ettringite through Fourier transform infrared spectroscopy,X-ray diffraction,particle size analysis and nucleation kinetic model.The experimental results indicate that the admixtures alter the formation of ettringite through physical adsorption,complexation and solution viscosity modulation without changing its chemical structure.Low concentrations of PCE inhibit size growth by forming an adsorption layer on the surface of ettringite,whereas high concentrations of PCE alter the size change of ettringite by modulating the distribution of ionic concentrations.TA significantly reduces the size of ettringite by complexing Ca^(2+).Sorbitol and PAM promote the local growth of ettringite at low concentrations,leading to larger sizes.But at high concentrations,the size growth of ettringite is inhibited due to the increase in viscosity or the enhancement of complexation.Matlab nucleation kinetic modelling further shows that the addition of admixtures enhances the initial nucleation during ettringite synthesis,with values ranging from 14.45%to 114.25%.However,the subsequent nucleation rate of ettringite is significantly affected,decreasing by 12.79%to 71.74%.The results provide a theoretical basis for the design of ettringite materials and the optimisation of the application of admixtures.
基金The National Natural Science Foundation of China(Grant No.72474013)the Beijing Health Technology Promotion Project(Grant No.BHTPP2024007)。
文摘This study investigated the factors contributing to intravenous admixture preparation errors(IAPEs)within Pharmacy Intravenous Admixture Services(PIVAS).A retrospective analysis was conducted on IAPEs documented in the PIVAS unit of a large multi-specialty hospital in China,which houses over 2000 beds,covering the period from January 1,2015 to December 31,2022.Drug preparation records were examined using a generalized linear mixed model(GLMM)to identify both univariate and multivariate factors associated with IAPE occurrences.A total of 824 IAPE cases were recorded during the study period,yielding an overall error rate of 0.018%.Univariate analysis identified drug categories(general drugs,anti-infective drugs,and antineoplastic drugs),preparation time(workdays),and years of work experience as significant determinants(P<0.05).Multivariate analysis further confirmed that drug categories(general and antineoplastic drugs),preparation time(workdays),and work experience remained statistically significant predictors of IAPE incidence(P<0.05).IAPEs in PIVAS were influenced by multiple factors,predominantly those related to personnel and drug characteristics.Targeted interventions,informed by multivariate analysis,are essential to mitigating these errors and enhancing medication safety.
基金Funded by the International Science and Technology Cooperation Project of the Key R&D Program of Science and Technology Innovation Yongjiang 2035。
文摘An evaluation method for self-healing capacity was designed,which includes the control of initial cracks and subsequent permeability testing.This method was employed to evaluate the self-healing behavior of mortars incorporating crystalline admixtures(CAs)under various conditions,including water immersion,limewater soaking,and wet-dry cycles,with varying CA dosages and crack widths.The experimental results indicate that cement possesses inherently self-healing capability.Limewater environments inhibits healing compared with water immersion;however,wet-dry cycles enhance the effectiveness of higher CA dosages.Increasing the CA content can not improve healing performance,and wide cracks(0.3 mm)substantially reduce the intrinsic self-healing potential of cement.
基金Hunan Provincial Department of Water Resources:Research on Formula Optimization and Performance Evaluation System of Ecological Concrete for River Water Quality Purification Based on the Dual Carbon Goal(Project No.:XSKJ2024064-44)。
文摘In this paper,the effects of four different mineral ginseng materials on the mechanical properties of mortar were studied,and the results showed that high territory,fly ash,and silica fume had an inhibitory effect on the drying shrinkage of mortar,and mineral powder increased the drying shrinkage of mortar.The high territory in the mineral admixture has the best effect on the inhibition of mortar drying shrinkage.The compressive strength and flexural strength of the mortar can be improved by adding a certain amount of mineral admixture,which increases the compressive strength by about 20%-40%and the flexural strength by about 20%-30%compared with the control group,and the improvement effect difference between different components is not large.
基金Supported by Regional Science Foundation of China,National Natural Science Foundation(No.82160820)General Program of Guizhou Provincial Natural Science Foundation[QianKeHe Foundation-ZK(2023)General153].
文摘[Objectives]To establish an HPLC method for the quantitative determination of multiple phenolic acid components in Tetracera asiatica medicinal material,providing a basis for establishing its quality standards.[Methods]An Inertsil ODS-C 18 column(250 mm×4.6 mm,5μm)was used.The mobile phase consisted of acetonitrile-0.2% phosphoric acid solution(10:90).The flow rate was 1.0 mL/min.The detection wavelength was 274 nm.The column temperature was 25℃.The injection volume was 10μL.The content of three components,gallic acid,protocatechuic acid,and protocatechualdehyde,was determined in 13 batches of T.asiatica.[Results]Gallic acid showed good linearity within the range of 0.020-6.400μg/mL,protocatechuic acid within 0.201-6.432μg/mL,and protocatechualdehyde within 0.202-6.464μg/mL(r>0.9990).The average recovery rates ranged from 98.61%to 101.17%,with RSD s between 1.21%and 2.69%.[Conclusions]The quantitative determination method established in this study is simple and feasible,and can provide a basis for the quality evaluation of T.asiatica.
基金the National Natural Science Foundation of China(No.22274021)Natural Science Foundation of Fujian Province(No.2022J01535)for financial support。
文摘Covalent organic frameworks(COFs)have demonstrated great potential in chromatographic separation because of unique structure and superior performance.Herein,single-crystal three-dimensional(3D)COFs with regular morphology,good monodispersity and high specific surface area,were used as a stationary phase for high-performance liquid chromatography(HPLC).The single-crystal 3D COFs packed column not only exhibits high efficiency in separating hydrophobic molecules involving substituted benzenes,halogenated benzenes,halogenated nitrobenzenes,aromatic amines,aromatic hydrocarbons(PAHs)and phthalate esters(PAEs),but also achieves baseline separation of acenaphthene and acenaphthylene with similar physical and chemical properties as well as environmental pollutants,which cannot be quickly separated on commercial C18 column and a polycrystalline 3D COFs packed column.Especially,the column efficiency of 17303-24255 plates/m was obtained for PAEs,and the resolution values for acenaphthene and acenaphthylene,and carbamazepine(CBZ)and carbamazepine-10,11-epoxide(CBZEP)were 1.7and 2.2,respectively.This successful application not only confirmed the great potential of the singlecrystal 3D COFs in HPLC separation of the organic molecules,but also facilitates the application of COFs in separation science.
基金supported by National Key Research and Development Program of China(Grant No.2022YFB3809000)Major Science and Technology Project of Gansu Province(Grant No.23ZDGA011)+1 种基金National Natural Science Foundation of China(Grant No.22275199,52105224)the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB04701022021).
文摘Compared to subtractive manufacturing and casting,3D printing(additive manufacturing)offers advantages,such as the rapid production of complex structures,reduced material waste,and environmental friendliness.Direct ink writing(DIW)is one of the most popular 3D printing techniques owing to its ability to print multiple materials simultaneously and its high compatibility with printing inks.However,DIW presents significant challenges,particularly in the printing of high-performance polymers.The main challenges are as follows:1.The rigid structures and reaction kinetics of high-performance polymers make developing new inks difficult.2.The limited types of available high-performance polymers underscore the need for new DIW-suitable materials.3.Layer-by-layer stacking weakens interlayer bonding,affecting the mechanical properties of the printed product.4.The accuracy and speed of DIW printing are insufficient for large-scale manufacturing.After introducing the topic,the requirements for DIW printing inks are first reviewed,emphasizing the importance of thixotropic agents.Then,research progress regarding DIW printing of high-performance polymers is comprehensively reviewed according to the requirements of different polymer inks.Additionally,the applications of these materials across various fields are summarized.Finally,the challenges in DIW printing of high-performance polymers,along with corresponding solutions and future development prospects,are discussed in detail.
文摘As electronic devices continue to evolve toward higher power densities,faster speeds,and smaller form factors,the demand for high-performance electronic packaging materials has become increasingly critical.These materials serve as the physical and functional interface between semiconductor components and their operating environment,impacting the overall reliability,thermal management,mechanical protection,and electrical performance of modern electronic systems.This study investigates the development,formulation,and performance evaluation of advanced packaging materials,focusing on polymer-based composites,metal and ceramic matrix systems,and nanomaterial-enhanced formulations.A comprehensive analysis of key performance metrics-including thermal conductivity,electrical insulation,mechanical robustness,and environmental resistance-is presented,alongside strategies for material optimization through interface engineering and processing innovations.Furthermore,the study explores cutting-edge integration technologies such as 3D packaging compatibility,low-temperature co-firing,and high-density interconnects.The findings provide critical insights into the structure-property-processing relationships that define the effectiveness of next-generation packaging materials and offer a roadmap for material selection and system integration in high-reliability electronic applications.
基金The Scholarship Supported by Ministry of Education of China for Research Abroad(No.3037[2006])the Excellent Doctoral Dissertation Foundation of Southeast University (No.YBTJ-0512)the National Basic Research Program of China(973Program)(No.2009CB623203)
文摘In order to investigate the effects of two mineral admixtures （i. e., fly ash and ground slag）on initial defects existing in concrete microstructures, a high-resolution X-ray micro-CT（ micro-focus computer tomography）is employed to quantitatively analyze the initial defects in four series of highperformance concrete （HPC）specimens with additions of different mineral admixtures. The nigh-resolution 3D images of microstructures and filtered defects are reconstructed by micro- CT software. The size distribution and volume fractions of initial defects are analyzed based on 3D and 2D micro-CT images. The analysis results are verified by experimental results of watersuction tests. The results show that the additions of mineral admixtures in concrete as cementitious materials greatly change the geometrical properties of the microstructures and the spatial features of defects by physical-chemistry actions of these mineral admixtures. This is the major cause of the differences between the mechanical behaviors of HPC with and without mineral admixtures when the water-to-binder ratio and the size distribution of aggregates are constant.
文摘In the present study, we aimed to analyze the irrational medical orders and evaluate the effect of pharmacy intervention on pharmacy intravenous admixture services of outpatient and emergency departments in our hospital. The irrational medical orders of PIVAS at the outpatient and emergency departments were retrospectively analyzed in Jun. 2015. We strengthened the pharmacy intervention on irrational medical orders since July 2015. All the cases were selected by systematic sampling method. Cased studied in Jun. 2015 served as the control group, whereas those studied in Jan. 2016 served as the intervention group. The irrational rate and the irrational number of daily average were compared between the control group and intervention group. The common type of irrational outpatient and emergency intravenous orders mainly included irrational use of solvents, irrational dosing interval and inappropriate compatibility of drugs. The irrational rate was reduced from 17.4% to 3.3% （P〈0.01）, and the irrational number of daily average was decreased from 5.23 to 1.00 （P〈0.01）. Pharmacy intervention can reduce the irrational rate of medical orders in our hospital, which is of great significance to promote rational drug use and improve medical quality.
基金National Natural Science Foundation of China (Grant No.21372015 and 20872006)
文摘A simple, sensible and reliable HPLC-DAD fingerprint analysis method for the raw materials of Oxytropisfalcata and Oxytropis chiliophylla, both of which were used as ＂Er-Da-Xia＂ in Tibetan medicines, was developed and then subsequently applied to analyze samples collected from different locations or times. 19 common fingerprint peaks for O. falcata, 24 for O. chiliophylla, and 11 for the two herbs were designated respectively, including 7 identified characteristic peaks existing in both herbs and 1 uniquely presenting in O. chiliophylla. Although there were some slight differences in the chemicals of O. falcata and O. chiliophylla, the main components of both herbs were consistent generally. The results provided scientific basis, at least from the chemical point of view, for the reasonablity of two herbs being used as the same drug in Tibetan medicines and for the necessary of further investigation on their detailed chemical and pharmacological differences.
文摘The expansion and micro-cracks of the mortar with composite mineral admixtures （fly ash, zeolite and slag） due to the alkali-silica reaction （ASR） are studied. Results show that composite mineral admixtures cannot absolutely diminish the ASR of mortar bars with the low-alkali cement and a highly reactive aggregate. But the expansion rate and the deleterious expansion of the mortar bar are mostly reduced with increasing composite mineral admixture. The influence of mineral admixtures on the fluidity of the paste and the strength of the mortar is also studied.
基金The National Natural Science Foundation of China(Grant No.81202918)the Open Project of National First-Class Key Discipline for Science of Chinese Materia Medica,Nanjing University of Chinese Medicine(Grant No.2011ZYX2-006)+2 种基金the Science and Technology Project of Hangzhou,China(Grant No.20130533B68 and 20131813A23)the Chinese Medicine Research Program of Zhejiang Province,China(Grant No.2014ZQ008 and 2015ZQ011)the Science Foundation of Zhejiang Chinese Medical University(Grant No.2011ZY25 and 2013ZZ12)
文摘The crude and processed Paeoniae Radix Alba-Atractylodis Macrocephalae Rhizoma herbal pairs, originated from Bai-zhu-shao-yao-san, are used to treat different diseases clinically. In order to evaluate the crude and processed Paeoniae Radix-Atractylodis Macrocephalae Rhizoma herbal pairs, a simple, easy, and sensitive high-performance liquid chromatography coupled with diode array detectors was developed for simultaneous determination of nine bioactive components in the herbal pairs. The calibration curve exhibited good linearity（r2≥0.9992）. The LODs and LOQs were ≤7.30 and 11.53 μg/m L, respectively. The intra-, inter-day and repeatability RSD values of the nine compounds were less than 3.86%, 2.71%, and 4.29%, respectively. The RSD stability values were less than 3.64%. The recovery of the method was in the range of 96.70%–102.10%, with RSD values less than 3.52%. The developed method can be applied to the intrinsic quality control of crude and processed Paeoniae Radix-Atractylodis Macrocephalae Rhizoma herbal pairs.
基金The Key Program of the National Natural Science Foundation of China(No.51438003)the National Basic Research Program of China(973 Program)(No.2015CB655105)
文摘The rice husk ash （ RHA） and silica （ Si02） nanoparticles are prepared from rice husk charcoal （RHC） by the methods of ventilated calcining and chemical precipitation, respectively, to remove the residual carbon which is harmful to cement composites. The structures and morphologies of these products are investigated by the Fourier transform infrared spectroscopy, X-ray diffraction, scanning/ transmission electron microscopy and N2 adsorption- desorption analyzer. The results show that the as-produced RHA and Si02 nanoparticles exist in amorphous phase without residual carbon, and exhibit porous structures with specific surface areas of 170.19 and 248. 67 m2 /g , respectively. The micro particles of RHA are aggregated by numerous loosely packed Si02 gel particles with the diameter of 50 to 100 nm. The Si02 nanoparticles are well dispersed with the average size of about 30 nm. Both the RHA and Si02 nanoparticles can significantly reduce the conductivity of saturated Ca（OH）2 solution and increase the early strength of the cement composites. They also exhibit high pozzolanic activity, indicating that they can be used as ecological nano mineral admixtures.
文摘The peroxyoxalate chemiluminescence(CL)detection of fatty acids in human se- rum combined with high-performance liquid chromatography (HPLC)is described.Some fatty acids in serum were extracted with a 1 :1(v/v)mixture of chloroform-n-heptane.2-(4-Hydrazinocarbonyl- phenyl)-4,5-diphenylimidazole (HCPI) was used as a fluorescent labelling reagent of the fatty acids. The labelling reaction was carried out at 30℃ for 1 h at pH 6.5 and the resulting reaction mixture was sudjected to HPLC. The labelled fatty acid C_(17)(P-C_(17))was used as the internal standard. The la- belled fatty acids C_(16) and C_(18) were separated within 18 min on an ODS-8OTM column (150 mm× 6 mm ID,5μm,Tosoh Japan).The calibrlation curves of fatty acids from the spiked control serum were Y_1=-0.003 7 + 0.0028X_1,r=0.994 for FA C_( 16) and Y_2=0.00 1 2 + 0.00098X_2,r=0.999 for FA C_( 18),respectively.The average recoveries of facids from the spiked contrl serum were 107.2%(n=8,RSD=4.3%)for FA C_(16) and 97.35%(n=8, RSD=4.0%)for FA C_(18),respectively.The lower detection limits of fatty acids after reaction were 12μmol per 20μl injection for FA C_(16) and 18 μmol per 20μl injection for FA C_(18),respectively(signal to noise ratio, S/N=2).The HPLC/CL method was applied to the determination of FA C_(16) and FA C_(18) in normal human serum and the results showed that the concentrations of fatty acids in normal human serum were 0.134 ± 0.009 μ mol/ml serum(n=5) for FA C_(16) and 0.052±0.028 μmol/ml serum(n=5)for FA C_(18),respectively.
基金supported by Beijing Kaiao Technology Development Co., Ltd., China and Beijing Friendship Hospital, Capital University of Medical Sciences Beijing
文摘Rhizoma Polygoni Bistortae has been widely used as an important medicinal herb in the Far East for a few thousand years, and it has gained more recognition in the last few decades. In the present study, we used a high-performance capillary electrophoresis （HPCE） method for determination of the gallic acid （GA） in Quanshen （QS） pieces. The analysis of GA in QS pieces was successfully achieved in less than 6 min by capillary electrophoresis with UV detection at a wavelength of 290 nm. The background electrolyte was 20 mmol/L sodium borate solution （pH 9.00）. The separation was performed in an uncoated fused-silica capillary （52 cm^50 lam） with an effective length of 40 cm, and the applied voltage was 20 kV. Sample solutions were injected for l0 s at an atmospheric pressure of 5 KPa. The result showed good resolution and precision （the intra-day RSD was 0.37%）. The calibration curves of the standard solutions were linear in the range of 0.22-2.25 mg/mL, with correlation coefficients greater than 0.9990. The recovery of the method ranged from 100.6% to 107.9%, and the average recovery of GA was 105.9% with an RSD of 3.63%. HPCE is a powerful technology, and it is the first time to successfully apply such a method for the determination of GA in the traditional Chinese medicine.
基金Program for Changjiang Scholar and Innovative Team in University(Grant No.985-2-063-112)
文摘We quantitatively determined four nucleosides, including cytidine, uridine, guanosine, and adenosine, in Carthamus tinctorius L. and Safflower injection. Separation was performed on a Zorbax Eclipse XDB-18 column using a gradient elution with mobile phases of 0.05% trifluoroacetic acid （TFA） aqueous solution （A） and methanol （B）. The assay was carried out at a flow rate of 1 mL/min at 25 ℃ with detection at 260 nm. Cytidine, uridine, adenosine and guanosine showed good linearity in the ranges of4.02-503μg/mL （r2= 0.9998）, 9.38-1407 μg/mL （rz = 0.9999）, 80.6-8060μg/mL （r2 = 0.9999） and 2.10---630μg/mL （r2 = 0.9987） with average recoveries of 97.2%, 94.5%, 98.6% and 108.6%, respectively. The contents of cytidine, uridine, adenosine and guanosine in different Carthamus tinctorius L. and Safflower injection were significantly different. This is the first report on the quantitative determination of nucleosides in Carthamus tinctorius L. and Safflower injection.
