There is a contradiction between the evolution rate of materials and the time resolution of SR-CT characterization in the in situ synchrotron radiation computed tomography(SR-CT)characterization of ultrafast evolution...There is a contradiction between the evolution rate of materials and the time resolution of SR-CT characterization in the in situ synchrotron radiation computed tomography(SR-CT)characterization of ultrafast evolution process.The sampling strategy of the ultra-sparse angle is an effective method for improving time resolution.Accurate reconstruction under sparse sampling conditions has always been a bottleneck problem.In recent years,convolutional neural networks have shown outstanding advantages in sparse-angle CT reconstruction given the development of deep learning.However,existing ideas did not consider the expression of high-frequency details in neural networks,limiting their application in accurate SR-CT characterization.A novel high-frequency information-constrained deep learning network(HFIC-Net)is proposed in response to this problem.Additional high-frequency information constraints are added to improve the accuracy of the reconstruction results.Further,a series of numerical reconstruction experiments are conducted to verify this new method,and the results indicate that the reconstruction results of HFIC-Net method effectively improve reconstruction quality.This new method uses only eight-angle projections to achieve the reconstruction effect of the filtered backprojection method(FBP)method in 360 projections.The results of the HFIC-Net method demonstrate clear boundaries and accurate detailed structures,correcting the misinformation caused by using other methods.For quantitative evaluation,the SSIM used to evaluate image structure similarity is increased from 0.1951,0.9212,and 0.9308 for FBP,FBP-Conv,and DDC-Net,respectively,to 0.9620 for HFIC-Net.Finally,the results of actual SR-CT experimental data indicate that the new method can suppress artifacts and achieve accurate reconstruction,and it is suitable for the in situ SR-CT accurate characterization of ultxafast evolution process.展开更多
Water storage in the Three Gorges Reservoir in China has increased the regional microseismicity.Bedding-rock landslides,one of the most common slope structures in the Three Gorges Reservoir,are highly prone to sliding...Water storage in the Three Gorges Reservoir in China has increased the regional microseismicity.Bedding-rock landslides,one of the most common slope structures in the Three Gorges Reservoir,are highly prone to sliding under seismic loading.Existing research primarily focuses on the stability of bedding rock landslides under strong earthquakes,while studies on the cumulative damage and long-term stability of bedding rock landslides under high-frequency microseismicity remain immature.In this study,we considered bedding rock landslides under high-frequency microseismicity in the Three Gorges Reservoir area as the research subject and equivalent microseismicity as pre-peak cyclic loading.First,we analyzed the shear strength deterioration of rock mass structural planes under pre-peak cyclic loading conditions and found that the deformation and failure of structural planes involve contact and damage effects.The shear strength of the rock mass structural planes under pre-peak cyclic loading conditions is affected by the confining pressure,loading rate,loading amplitude,and number of loading cycles.Among these factors,the shear strength of the structural planes was the most sensitive to the number of loading cycles.As the number of cycles increased,the rock mass structural planes underwent three stages:stress adjustment(increase in shear strength),fatigue damage(gradual decrease in shear strength),and structural failure(rapid decrease in shear strength).The stability of bedding rock landslides under high-frequency microseismicity was analyzed,revealing that the stability of bedding rock landslides under high-frequency microseismicity can be divided into three stages:short-term enhancement,gradual degradation,and rapid deterioration,exhibiting characteristics of gradual and sudden changes.展开更多
Physics-informed neural networks(PINNs)have been shown as powerful tools for solving partial differential equations(PDEs)by embedding physical laws into the network training.Despite their remarkable results,complicate...Physics-informed neural networks(PINNs)have been shown as powerful tools for solving partial differential equations(PDEs)by embedding physical laws into the network training.Despite their remarkable results,complicated problems such as irregular boundary conditions(BCs)and discontinuous or high-frequency behaviors remain persistent challenges for PINNs.For these reasons,we propose a novel two-phase framework,where a neural network is first trained to represent shape functions that can capture the irregularity of BCs in the first phase,and then these neural network-based shape functions are used to construct boundary shape functions(BSFs)that exactly satisfy both essential and natural BCs in PINNs in the second phase.This scheme is integrated into both the strong-form and energy PINN approaches,thereby improving the quality of solution prediction in the cases of irregular BCs.In addition,this study examines the benefits and limitations of these approaches in handling discontinuous and high-frequency problems.Overall,our method offers a unified and flexible solution framework that addresses key limitations of existing PINN methods with higher accuracy and stability for general PDE problems in solid mechanics.展开更多
In this paper,a fast step heterodyne light-induced thermoelastic spectroscopy(SH-LITES)sensor using a high-frequency quartz tuning fork(QTF)with resonant frequency of~100 kHz is reported for the first time.The theoret...In this paper,a fast step heterodyne light-induced thermoelastic spectroscopy(SH-LITES)sensor using a high-frequency quartz tuning fork(QTF)with resonant frequency of~100 kHz is reported for the first time.The theoretical principle of heterodyne LITES(H-LITES)signal generation is analyzed firstly,and an acetylene(C_(2)H_(2))H-LITES sensor is established to verify its performance.Experimental comparisons between the high-frequency QTF and a standard commercial QTF with resonant frequency of~32.768 kHz reveal that the high-frequency QTF exhibits a tenfold faster response time.Specifically,the H-LITES sensor with this QTF achieves a 33 ms measurement cycle,90%shorter than commercial counterparts.Furthermore,The SH-LITES technique is proposed to further shorten the scanning time to 15 ms,which achieves the shortest LITES measurement time known to date.To demonstrate its advantages in dynamic gas detection,an H_(2)O-LITES system integrating both QTF types is constructed for real-time monitoring of H_(2)O concentration during different respiration patterns.Comparative measurements show that the SH-LITES more accurately captures dynamic H_(2)O concentration fluctuations during respiration,outperforming the commercial QTF-based H-LITES sensor in rapid response scenarios.展开更多
Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the stru...Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the structural safety of supersonic vehicles,but it has been rarely investigated.Given that existing methods are inefficient for high-frequency dynamic analysis in multi-physics fields,the present work addresses this challenge by proposing a Stochastic Energy Finite Element Method(SEFEM).SEFEM uses energy density instead of displacement to describe the dynamic response,thereby significantly enhancing its efficiency.In SEFEM,the effects of aerodynamic and thermal loads on the energy propagation characteristics are studied analytically and incorporated into the energy density governing equation.These effects are also considered when calculating the input power generated by the acoustic load,and two effective approaches named Frequency Response Function Method(FRFM)and Mechanical Impedance Method(MIM)are developed accordingly and integrated into SEFEM.The good accuracy,applicability,and high efficiency of the proposed SEFEM are demonstrated through numerical simulations performed on a two-dimensional panel under aero-thermoacoustic loads.Additionally,the effects and underlying mechanisms of aero-thermo-acoustic loads on the high-frequency response are explored.This work not only presents an efficient approach for predicting high-frequency dynamic response of panels subjected to aero-thermo-acoustic loads,but also provides insights into the high-frequency dynamic characteristics in multi-physics fields.展开更多
China has a long history of coal mining,among which open-pit coal mines have a large number of small coal mine goafs underground.The distribution,shape,structure and other characteristics of goafs are isolated and dis...China has a long history of coal mining,among which open-pit coal mines have a large number of small coal mine goafs underground.The distribution,shape,structure and other characteristics of goafs are isolated and discontinuous,and there is no definite geological law to follow,which seriously threatens the safety of coal mine production and personnel life.Conventional ground geophysical methods have low accuracy in detecting goaf areas affected by mechanical interference from open-pit mines,especially for waterless goaf areas,which cannot be detected by existing methods.This article proposes the use of high-frequency electromagnetic waves for goaf detection.The feasibility of using drilling radar to detect goaf was theoretically analyzed,and a goaf detection model was established.The response characteristics of different fillers in the goaf under different frequencies of high-frequency electromagnetic waves were simulated and analyzed.In a certain open-pit mine in Inner Mongolia,100MHz high-frequency electromagnetic waves were used to detect the goaf through directional drilling on the ground.After detection,excavation verification was carried out,and the location of one goaf detected was verified.The results of engineering practice show that the application of high-frequency electromagnetic waves in goaf detection expands the detection radius of boreholes,has the advantages of high efficiency and accuracy,and has important theoretical and practical significance.展开更多
This paper presents a numerical study on the high-frequency wave loads and ringing response of offshore wind turbine foundations exposed to moderately steep transient water waves.Input wave groups are generated by the...This paper presents a numerical study on the high-frequency wave loads and ringing response of offshore wind turbine foundations exposed to moderately steep transient water waves.Input wave groups are generated by the technique of frequency-focusing,and the numerical simulation of focused waves is based on the NewWave model and a Fourier time-stepping procedure.The proposed model is validated by comparison with the published laboratory data.In respect of both the wave elevations and the underlying water particle kinematics,the numerical results are in excellent agreement with the experimental data.Furthermore,the local evolution of power spectra and the transfer of energy into higher frequencies can be clearly identified.Then the generalized FNV theory and Rainey’s model are applied respectively to calculate the nonlinear wave loads on a bottom-hinged vertical cylinder in focused waves.Resonant ringing response excited by the nonlinear high-frequency wave loads is found in the numerical simulation when frequency ratios(natural frequency of the structure to peak frequency of wave spectra)are equal to 3–5.Dynamic amplification factor of ringing response is also investigated for different dynamic properties(natural frequency and damping ratio)of the structure.展开更多
Salience theory has been proposed as a new stock trading strategy.To assess the validity of this proposal,a complex decision trading system was constructed based on salience theory,a variational mode decomposition(VMD...Salience theory has been proposed as a new stock trading strategy.To assess the validity of this proposal,a complex decision trading system was constructed based on salience theory,a variational mode decomposition(VMD)model,a bidirectional gated recurrent unit(BiGRU)model,and high-frequency trading.The system selected 30 Chinese new energy concept stocks,ranked the stocks using salience theory,and selected the top and bottom three stocks for two portfolios.Twelve stages were established,following which the VMD and BiGRU models were applied to the predictions.The final predicted annualized returns for the high ST(salience theory value)group A(GA)and low ST group B(GB)were 194.06%and 165.88%,respectively.This finding validates the powerful utility of salience theory and deep learning to analyze the Chinese new energy market.Moreover,it explains the theoretical practicality issues that the short selling restriction is the essential reason,or even perhaps the only reason,that leads to the strength of salience theory.展开更多
Articular cartilage maintains joint homeostasis by adapting to mechanical loading,but both insufficient and excessive loading can impair cartilage integrity.Whether mechanical activity should be restricted in early os...Articular cartilage maintains joint homeostasis by adapting to mechanical loading,but both insufficient and excessive loading can impair cartilage integrity.Whether mechanical activity should be restricted in early osteoarthritis(OA),particularly among exercise enthusiasts,remains controversial.Here,we established in vitro and in vivo models of prolonged moderate mechanical loading(7.5%strain,1 Hz)and analyzed human cartilage from weight-bearing and non-weight-bearing regions using RNA sequencing.Prolonged exposure(≥12 h)significantly increased chondrocyte apoptosis(2.3-fold),reduced expression of the chondrogenic transcription factor SOX9 and the matrix markers COL2A1,and elevated nerve growth factor(NGF)expression(1.8-fold),accompanied by enrichment of neural sensitization and inflammatory pathways.Immunofluorescence staining revealed NGF accumulation in mechanically stressed cartilage.Unlike high-intensity stress,which led to immediate apoptosis,moderate loading induced a delayed pro-apoptotic response after 12 h.These findings indicate that prolonged moderate mechanical loading may promote chondrocyte apoptosis through an NGFmediated inflammatory microenvironment and provide mechanistic evidence suggesting that patients with early OA may benefit from limiting high-impact or prolonged moderate-intensity exercise sessions to prevent cartilage damage and guide rehabilitation.展开更多
The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel l...The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel logging method for detection of high-resistance formations in OBM using highfrequency electrodes. The method addresses the issue of shallow depth of investigation(DOI) in existing electrical logging instruments, while simultaneously ensuring the vertical resolution. Based on the principle of current continuity, the total impedance of the loop is obtained by equating the measurement loop to the series form of a capacitively coupled circuit. and its validity is verified in a homogeneous formation model and a radial two-layer formation model with a mud standoff. Then, the instrument operating frequency and electrode system parameters were preferentially determined by numerical simulation, and the effect of mud gap on impedance measurement was investigated. Subsequently, the DOI of the instrument was investigated utilizing the pseudo-geometric factor defined by the real part of impedance. It was determined that the detection depth of the instrument is 8.74 cm, while the effective vertical resolution was not less than 2 cm. Finally, a focused high-frequency electrode-type instrument was designed by introducing a pair of focused electrodes, which effectively enhanced the DOI of the instrument and was successfully deployed in the Oklahoma formation model. The simulation results demonstrate that the novel method can achieve a detection depth of 17.40 cm in highly-resistive formations drilling with OBM, which is approximately twice the depth of detection of the existing oil-based mud microimager instruments. Furthermore, its effective vertical resolution remains at or above 2 cm,which is comparable to the resolution of the existing OBM electrical logging instrument.展开更多
Objective:To analyze the significance of high-frequency ultrasound in differentiating benign and malignant breast micronodules.Methods:Eighty-five patients with breast micronodules admitted for diagnosis between Octob...Objective:To analyze the significance of high-frequency ultrasound in differentiating benign and malignant breast micronodules.Methods:Eighty-five patients with breast micronodules admitted for diagnosis between October 2022 and October 2024 were selected for high-frequency ultrasound diagnosis.The diagnostic efficacy of high-frequency ultrasound was evaluated by comparing it with the results of surgical pathology.Results:High-frequency ultrasound detected 50 benign nodules,primarily breast fibroadenomas,and 35 malignant nodules,mainly breast ductal carcinoma in situ.Based on surgical pathology results,the diagnostic accuracy of high-frequency ultrasound was 96.47%,specificity was 97.96%,and sensitivity was 94.44%.In high-frequency ultrasound diagnosis,the proportion of grade III and IV blood flow in malignant nodules was higher than that in benign nodules,while the proportion of regular shape and clear margins was lower.The proportion of microcalcifications and posterior echo attenuation was higher in malignant nodules,and the resistance index(RI)and peak blood flow velocity were lower than those in benign nodules(P<0.05).Conclusion:High-frequency ultrasound can effectively differentiate benign and malignant breast micronodules,determine specific nodule types,and exhibits high diagnostic accuracy and sensitivity.Additionally,benign and malignant nodules can be differentiated based on the grading of blood flow signals,sonographic features,and blood flow velocity,providing reasonable guidance for subsequent treatment plans.展开更多
New electric power systems characterized by a high proportion of renewable energy and power electronics equipment face significant challenges due to high-frequency(HF)electromagnetic interference from the high-speed s...New electric power systems characterized by a high proportion of renewable energy and power electronics equipment face significant challenges due to high-frequency(HF)electromagnetic interference from the high-speed switching of power converters.To address this situation,this paper offers an in-depth review of HF interference problems and challenges originating from power electronic devices.First,the root cause of HF electromagnetic interference,i.e.,the resonant response of the parasitic parameters of the system to high-speed switching transients,is analyzed,and various scenarios of HF interference in power systems are highlighted.Next,the types of HF interference are summarized,with a focus on common-mode interference in grounding systems.This paper thoroughly reviews and compares various suppression methods for conducted HF interference.Finally,the challenges involved and suggestions for addressing emerging HF interference problems from the perspective of both power electronics equipment and power systems are discussed.This review aims to offer a structured understanding of HF interference problems and their suppression techniques for researchers and practitioners.展开更多
Objective:To analyze the therapeutic effect of high-frequency electrosurgical knife surgery guided by painless digestive endoscopy(PDE)in elderly patients with gastrointestinal polyps(GP).Methods:A total of 100 elderl...Objective:To analyze the therapeutic effect of high-frequency electrosurgical knife surgery guided by painless digestive endoscopy(PDE)in elderly patients with gastrointestinal polyps(GP).Methods:A total of 100 elderly GP patients admitted between June 2021 and December 2022 were selected.Patients were randomly divided into two groups:the painless group(50 cases)underwent high-frequency electrosurgical knife surgery guided by PDE,while the conventional group(50 cases)underwent the same surgery guided by traditional digestive endoscopy(DE).The total treatment efficacy,perioperative indicators,gastrointestinal hormone levels,oxidative stress(OS)markers,and complication rates were compared between the two groups.Results:The total treatment efficacy in the painless group was higher than that in the conventional group,and perioperative indicators were superior in the painless group(P<0.05).One week after treatment,the gastrointestinal hormone levels and OS-related markers in the painless group were better than those in the conventional group(P<0.05).The complication rate in the painless group was lower than in the conventional group(P<0.05).Conclusion:High-frequency electrosurgical knife surgery guided by PDE improves the effectiveness of polyp removal in elderly GP patients and accelerates postoperative recovery.It also protects gastrointestinal function,reduces postoperative OS,and ensures higher surgical safety.展开更多
Single-shot ultrafast compressed imaging(UCI)is an effective tool for studying ultrafast dynamics in physics,chemistry,or material science because of its excellent high frame rate and large frame number.However,the ra...Single-shot ultrafast compressed imaging(UCI)is an effective tool for studying ultrafast dynamics in physics,chemistry,or material science because of its excellent high frame rate and large frame number.However,the random code(Rcode)used in traditional UCI will lead to low-frequency noise covering high-frequency information due to its uneven sampling interval,which is a great challenge in the fidelity of large-frame reconstruction.Here,a high-frequency enhanced compressed active photography(H-CAP)is proposed.By uniformizing the sampling interval of R-code,H-CAP capture the ultrafast process with a random uniform sampling mode.This sampling mode makes the high-frequency sampling energy dominant,which greatly suppresses the low-frequency noise blurring caused by R-code and achieves high-frequency information of image enhanced.The superior dynamic performance and large-frame reconstruction ability of H-CAP are verified by imaging optical self-focusing effect and static object,respectively.We applied H-CAP to the spatial-temporal characterization of double-pulse induced silicon surface ablation dynamics,which is performed within 220 frames in a single-shot of 300 ps.H-CAP provides a high-fidelity imaging method for observing ultrafast unrepeatable dynamic processes with large frames.展开更多
Soft magnetic composites made from metallic magnetic particles with an easy magnetization plane(referred to as easy-plane metallic soft magnetic composites(SMC))are considered ideal materials for the next generation o...Soft magnetic composites made from metallic magnetic particles with an easy magnetization plane(referred to as easy-plane metallic soft magnetic composites(SMC))are considered ideal materials for the next generation of power electronic devices.This advantage is attributed to their ability to maintain high permeability at elevated frequencies.Despite these advantages,a definitive mathematical model that connects the high-frequency magnetic properties(e.g.,effective permeability)of easy-plane metallic SMCs to the intrinsic properties of the particles is still lacking.In this work,a theoretical calculation model for the effective permeability of easy-plane metallic SMCs was formulated.This model was derived from a skin effect-corrected Landau-Lifshitz-Gilbert(LLG)equation and integrated with effective medium theory incorporating inter-particle interaction.To validate the model,we prepared samples of easy-plane Y_(2)Co_(17)particle/PU SMCs with varying particle sizes and volume fractions.The experimental results showed a strong agreement with the calculated values.This research offers critical theoretical backing for the design and optimization of soft magnetic materials intended for high-frequency applications.展开更多
High-frequency pulsed(HFP)gas tungsten arc welding(GTAW)has shown excellent performance in welding of aluminum alloys in recent years,which makes itself a promisingly potential technique for part manufacturing in avia...High-frequency pulsed(HFP)gas tungsten arc welding(GTAW)has shown excellent performance in welding of aluminum alloys in recent years,which makes itself a promisingly potential technique for part manufacturing in aviation industry.However,existing researches generally focuses on the effect of a single parameter while lacks multivariable researches.Considering of the fact that gap and misalignment are inevitable in real part clamping,adaptive intelligent welding is usually used during automatic manufacturing,which means under the control of filler wire amount per length of a weld,other parameters including current,welding speed and wire feed speed during one single weld are changing according to the specific clamping situation.Therefore,the influence of specific energy input led by different welding parameters within one adaptive welding program on microstructure and mechanical property of the weld needs to be clarified.This study investigates the effect of welding heat input(ranging from 1048.3 J/mm to 825.6 J/mm within one adaptive welding program control)on the formation quality of 3.25 mm thick 6061 aluminum alloy joints fabricated by HFP-GTAW with 4043 filler wire.According to the obtained results,non-monotonic relationship between heat input and porosity,with an optimal minimum of 4.92%achieved at an intermediate heat input of 856.8 J/mm.The 21.2%decrease of energy input during welding process would reduce the average grain size in the weld center and adjacent to fusion line by 18.6%and 19.4%,respectively.The ratios between fluctuation range to minimum value in average yield and the relative ranges of yield strength and ultimate tensile strength across the tested heat inputs were 14.7%and 12.7%,respectively.The findings provide a general overview on how the microstructure and mechanical properties would fluctuate in an adaptively controlled HFP-GTAW fabricated aluminum alloy weld.展开更多
With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limite...With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limited.This poses challenges for conventional fault distance estimation methods,which are often tailored to simple topologies and are thus difficult to apply to large-scale,multi-node DC networks.To address this,a fault distance estimation method based on sparse measurement of high-frequency electrical quantities is proposed in this paper.First,a preliminary fault line identification model based on compressed sensing is constructed to effectively narrow the fault search range and improve localization efficiency.Then,leveraging the high-frequency impedance characteristics and the voltage-current relationship of electrical quantities,a fault distance estimation approach based on high-frequency measurements from both ends of a line is designed.This enables accurate distance estimation even when the measurement devices are not directly placed at both ends of the faulted line,overcoming the dependence on specific sensor placement inherent in traditional methods.Finally,to further enhance accuracy,an optimization model based on minimizing the high-frequency voltage error at the fault point is introduced to reduce estimation error.Simulation results demonstrate that the proposed method achieves a fault distance estimation error of less than 1%under normal conditions,and maintains good performance even under adverse scenarios.展开更多
The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model ...The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model for epoxy resin encapsulated nano HFTs, which aims to precisely predict the temperature distribution inside the transformer in combination with the finite element method(FEM). A magnetothermal bidirectional coupling 3DTN model is established by analyzing the thermal conduction between the core, windings, and epoxy resin, while also considering the convection and radiation heat transfer mechanisms on the surface of the epoxy resin. The model considers the impact of loss distribution in the core and windings on the temperature field and adopts a simplified 1/2 thermal network model to reduce computational complexity. Furthermore, the results of FEM are compared with experimental results to verify the accuracy of the 3DTN model in predicting the temperature rise of nano HFT. The results show that the 3DTN model reduces errors by an average of 5.25% over the traditional two-dimensional thermal network(2DTN) model, particularly for temperature distributions in the windings and core. This paper provides a temperature rise prediction method for the thermal design and offers a theoretical basis and engineering guidance for the optimization of their thermal management systems.展开更多
Load frequency control(LFC)is a critical function to balance the power consumption and generation.Thegrid frequency is a crucial indicator for maintaining balance.However,the widely used information and communication ...Load frequency control(LFC)is a critical function to balance the power consumption and generation.Thegrid frequency is a crucial indicator for maintaining balance.However,the widely used information and communication infrastructure for LFC increases the risk of being attacked by malicious actors.The dynamic load altering attack(DLAA)is a typical attack that can destabilize the power system,causing the grid frequency to deviate fromits nominal value.Therefore,in this paper,we mathematically analyze the impact of DLAA on the stability of the grid frequency and propose the network parameter regulation(NPR)to mitigate the impact.To begin with,the dynamic LFC model is constructed by highlighting the importance of the network parameter.Then,we model the DLAA and analyze its impact on LFC using the theory of second-order dynamic systems.Finally,we model the NPR and prove its effect in mitigating the DLAA.Besides,we construct a least-effort NPR considering its infrastructure cost and aim to reduce the operation cost.Finally,we carry out extensive simulations to demonstrate the impact of the DLAA and evaluate the mitigation performance of NPR.The proposed cost-benefit NPR approach can not only mitigate the impact of DLAA with 100%and also save 41.18$/MWh in terms of the operation cost.展开更多
This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and...This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and the stress and aerodynamic load measurement points are reasonably arranged accordingly.The actual measurement is carried out in combination with the operating conditions of the existing lines.The stress variations and spectral characteristics of the train under different speed levels(80,160,180,200 km/h),tunnel entry and exit,and scraper action conditions were compared and analyzed.The stress amplification factors under tunnel intersection and scraper action were obtained,providing boundary conditions for the design of wipers for highspeed s.The research results show that the maximum stress of the wiper structure obtained through simulation calculation is concentrated at the connection of the wiper arm.Structural stress increases with the rise of speed grade.The stress increases by 1.11 times when the tunnel meets.When the scraper operates,the stress on the scraper arm increases by 4.1–7.6 times.Due to the broadband excitation effect of the aerodynamic load,the spectral energy of the structure is relatively high at the natural frequency,which excites the natural mode of the wiper.展开更多
基金supported by the National Nature Science Foundation of China(Nos.12027901 and 12041202)Synchrotron Radiation Joint Fund of University of Science and Technology of China(Nos.KY2090000059 and KY2090000054)。
文摘There is a contradiction between the evolution rate of materials and the time resolution of SR-CT characterization in the in situ synchrotron radiation computed tomography(SR-CT)characterization of ultrafast evolution process.The sampling strategy of the ultra-sparse angle is an effective method for improving time resolution.Accurate reconstruction under sparse sampling conditions has always been a bottleneck problem.In recent years,convolutional neural networks have shown outstanding advantages in sparse-angle CT reconstruction given the development of deep learning.However,existing ideas did not consider the expression of high-frequency details in neural networks,limiting their application in accurate SR-CT characterization.A novel high-frequency information-constrained deep learning network(HFIC-Net)is proposed in response to this problem.Additional high-frequency information constraints are added to improve the accuracy of the reconstruction results.Further,a series of numerical reconstruction experiments are conducted to verify this new method,and the results indicate that the reconstruction results of HFIC-Net method effectively improve reconstruction quality.This new method uses only eight-angle projections to achieve the reconstruction effect of the filtered backprojection method(FBP)method in 360 projections.The results of the HFIC-Net method demonstrate clear boundaries and accurate detailed structures,correcting the misinformation caused by using other methods.For quantitative evaluation,the SSIM used to evaluate image structure similarity is increased from 0.1951,0.9212,and 0.9308 for FBP,FBP-Conv,and DDC-Net,respectively,to 0.9620 for HFIC-Net.Finally,the results of actual SR-CT experimental data indicate that the new method can suppress artifacts and achieve accurate reconstruction,and it is suitable for the in situ SR-CT accurate characterization of ultxafast evolution process.
基金sponsored by the General Program of the National Natural Science Foundation of China(Grant No.42407221)the Open Fund of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Grant No.SKLGP2024K009)the Hubei Provincial Natural Science Foun-dation,China(Grant No.2023AFB567).
文摘Water storage in the Three Gorges Reservoir in China has increased the regional microseismicity.Bedding-rock landslides,one of the most common slope structures in the Three Gorges Reservoir,are highly prone to sliding under seismic loading.Existing research primarily focuses on the stability of bedding rock landslides under strong earthquakes,while studies on the cumulative damage and long-term stability of bedding rock landslides under high-frequency microseismicity remain immature.In this study,we considered bedding rock landslides under high-frequency microseismicity in the Three Gorges Reservoir area as the research subject and equivalent microseismicity as pre-peak cyclic loading.First,we analyzed the shear strength deterioration of rock mass structural planes under pre-peak cyclic loading conditions and found that the deformation and failure of structural planes involve contact and damage effects.The shear strength of the rock mass structural planes under pre-peak cyclic loading conditions is affected by the confining pressure,loading rate,loading amplitude,and number of loading cycles.Among these factors,the shear strength of the structural planes was the most sensitive to the number of loading cycles.As the number of cycles increased,the rock mass structural planes underwent three stages:stress adjustment(increase in shear strength),fatigue damage(gradual decrease in shear strength),and structural failure(rapid decrease in shear strength).The stability of bedding rock landslides under high-frequency microseismicity was analyzed,revealing that the stability of bedding rock landslides under high-frequency microseismicity can be divided into three stages:short-term enhancement,gradual degradation,and rapid deterioration,exhibiting characteristics of gradual and sudden changes.
基金Project supported by the Basic Science Research Program through the National Research Foundation(NRF)of Korea funded by the Ministry of Science and ICT(No.RS-2024-00337001)。
文摘Physics-informed neural networks(PINNs)have been shown as powerful tools for solving partial differential equations(PDEs)by embedding physical laws into the network training.Despite their remarkable results,complicated problems such as irregular boundary conditions(BCs)and discontinuous or high-frequency behaviors remain persistent challenges for PINNs.For these reasons,we propose a novel two-phase framework,where a neural network is first trained to represent shape functions that can capture the irregularity of BCs in the first phase,and then these neural network-based shape functions are used to construct boundary shape functions(BSFs)that exactly satisfy both essential and natural BCs in PINNs in the second phase.This scheme is integrated into both the strong-form and energy PINN approaches,thereby improving the quality of solution prediction in the cases of irregular BCs.In addition,this study examines the benefits and limitations of these approaches in handling discontinuous and high-frequency problems.Overall,our method offers a unified and flexible solution framework that addresses key limitations of existing PINN methods with higher accuracy and stability for general PDE problems in solid mechanics.
基金financial supports from the National Natural Science Foundation of China(Grant No.62335006,62275065,624B2050,62022032,and 62405078)Open Subject of Hebei Key Laboratory of Advanced Laser Technology and Equipment(HBKL-ALTE2025001)+2 种基金Heilongjiang Postdoctoral Fund(Grant No.LBH-Z23144 and LBH-Z24155)Natural Science Foundation of Heilongjiang Province(Grant No.LH2024F031)China Postdoctoral Science Foundation(Grant No.2024M764172).
文摘In this paper,a fast step heterodyne light-induced thermoelastic spectroscopy(SH-LITES)sensor using a high-frequency quartz tuning fork(QTF)with resonant frequency of~100 kHz is reported for the first time.The theoretical principle of heterodyne LITES(H-LITES)signal generation is analyzed firstly,and an acetylene(C_(2)H_(2))H-LITES sensor is established to verify its performance.Experimental comparisons between the high-frequency QTF and a standard commercial QTF with resonant frequency of~32.768 kHz reveal that the high-frequency QTF exhibits a tenfold faster response time.Specifically,the H-LITES sensor with this QTF achieves a 33 ms measurement cycle,90%shorter than commercial counterparts.Furthermore,The SH-LITES technique is proposed to further shorten the scanning time to 15 ms,which achieves the shortest LITES measurement time known to date.To demonstrate its advantages in dynamic gas detection,an H_(2)O-LITES system integrating both QTF types is constructed for real-time monitoring of H_(2)O concentration during different respiration patterns.Comparative measurements show that the SH-LITES more accurately captures dynamic H_(2)O concentration fluctuations during respiration,outperforming the commercial QTF-based H-LITES sensor in rapid response scenarios.
基金financially supported by the National Natural Science Foundation of China(Nos.12302228 and 12372170)。
文摘Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the structural safety of supersonic vehicles,but it has been rarely investigated.Given that existing methods are inefficient for high-frequency dynamic analysis in multi-physics fields,the present work addresses this challenge by proposing a Stochastic Energy Finite Element Method(SEFEM).SEFEM uses energy density instead of displacement to describe the dynamic response,thereby significantly enhancing its efficiency.In SEFEM,the effects of aerodynamic and thermal loads on the energy propagation characteristics are studied analytically and incorporated into the energy density governing equation.These effects are also considered when calculating the input power generated by the acoustic load,and two effective approaches named Frequency Response Function Method(FRFM)and Mechanical Impedance Method(MIM)are developed accordingly and integrated into SEFEM.The good accuracy,applicability,and high efficiency of the proposed SEFEM are demonstrated through numerical simulations performed on a two-dimensional panel under aero-thermoacoustic loads.Additionally,the effects and underlying mechanisms of aero-thermo-acoustic loads on the high-frequency response are explored.This work not only presents an efficient approach for predicting high-frequency dynamic response of panels subjected to aero-thermo-acoustic loads,but also provides insights into the high-frequency dynamic characteristics in multi-physics fields.
文摘China has a long history of coal mining,among which open-pit coal mines have a large number of small coal mine goafs underground.The distribution,shape,structure and other characteristics of goafs are isolated and discontinuous,and there is no definite geological law to follow,which seriously threatens the safety of coal mine production and personnel life.Conventional ground geophysical methods have low accuracy in detecting goaf areas affected by mechanical interference from open-pit mines,especially for waterless goaf areas,which cannot be detected by existing methods.This article proposes the use of high-frequency electromagnetic waves for goaf detection.The feasibility of using drilling radar to detect goaf was theoretically analyzed,and a goaf detection model was established.The response characteristics of different fillers in the goaf under different frequencies of high-frequency electromagnetic waves were simulated and analyzed.In a certain open-pit mine in Inner Mongolia,100MHz high-frequency electromagnetic waves were used to detect the goaf through directional drilling on the ground.After detection,excavation verification was carried out,and the location of one goaf detected was verified.The results of engineering practice show that the application of high-frequency electromagnetic waves in goaf detection expands the detection radius of boreholes,has the advantages of high efficiency and accuracy,and has important theoretical and practical significance.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51879039 and 51490672)。
文摘This paper presents a numerical study on the high-frequency wave loads and ringing response of offshore wind turbine foundations exposed to moderately steep transient water waves.Input wave groups are generated by the technique of frequency-focusing,and the numerical simulation of focused waves is based on the NewWave model and a Fourier time-stepping procedure.The proposed model is validated by comparison with the published laboratory data.In respect of both the wave elevations and the underlying water particle kinematics,the numerical results are in excellent agreement with the experimental data.Furthermore,the local evolution of power spectra and the transfer of energy into higher frequencies can be clearly identified.Then the generalized FNV theory and Rainey’s model are applied respectively to calculate the nonlinear wave loads on a bottom-hinged vertical cylinder in focused waves.Resonant ringing response excited by the nonlinear high-frequency wave loads is found in the numerical simulation when frequency ratios(natural frequency of the structure to peak frequency of wave spectra)are equal to 3–5.Dynamic amplification factor of ringing response is also investigated for different dynamic properties(natural frequency and damping ratio)of the structure.
基金supported by the National Natural Science Foundation of China(Grant Nos.72032006 and 92146005).
文摘Salience theory has been proposed as a new stock trading strategy.To assess the validity of this proposal,a complex decision trading system was constructed based on salience theory,a variational mode decomposition(VMD)model,a bidirectional gated recurrent unit(BiGRU)model,and high-frequency trading.The system selected 30 Chinese new energy concept stocks,ranked the stocks using salience theory,and selected the top and bottom three stocks for two portfolios.Twelve stages were established,following which the VMD and BiGRU models were applied to the predictions.The final predicted annualized returns for the high ST(salience theory value)group A(GA)and low ST group B(GB)were 194.06%and 165.88%,respectively.This finding validates the powerful utility of salience theory and deep learning to analyze the Chinese new energy market.Moreover,it explains the theoretical practicality issues that the short selling restriction is the essential reason,or even perhaps the only reason,that leads to the strength of salience theory.
基金supported by the Zhejiang Medical and Health Innovation Talent Support Project(Grant No.2021RC128 to S.S.)Zhejiang Medicine and Health Science and Technology Project(2025KY1540 to J.J.L.)+3 种基金Zhejiang Province Health Science and Technology Project(2024KY409 and 2021KY1086 to J.Y.L.)Huzhou Science and Technology Planning Project(2020GY10 to W.L.,2022GZ65 to J.Y.L.)Huzhou Basic and Clinical Translation of Orthopedics Key Laboratory(Grant No.HZGKSYS01Y to S.S.)South Taihu Lake Outstanding Young Health Talents Cultivation Program(Grant No.rsk2023001 to S.S.).
文摘Articular cartilage maintains joint homeostasis by adapting to mechanical loading,but both insufficient and excessive loading can impair cartilage integrity.Whether mechanical activity should be restricted in early osteoarthritis(OA),particularly among exercise enthusiasts,remains controversial.Here,we established in vitro and in vivo models of prolonged moderate mechanical loading(7.5%strain,1 Hz)and analyzed human cartilage from weight-bearing and non-weight-bearing regions using RNA sequencing.Prolonged exposure(≥12 h)significantly increased chondrocyte apoptosis(2.3-fold),reduced expression of the chondrogenic transcription factor SOX9 and the matrix markers COL2A1,and elevated nerve growth factor(NGF)expression(1.8-fold),accompanied by enrichment of neural sensitization and inflammatory pathways.Immunofluorescence staining revealed NGF accumulation in mechanically stressed cartilage.Unlike high-intensity stress,which led to immediate apoptosis,moderate loading induced a delayed pro-apoptotic response after 12 h.These findings indicate that prolonged moderate mechanical loading may promote chondrocyte apoptosis through an NGFmediated inflammatory microenvironment and provide mechanistic evidence suggesting that patients with early OA may benefit from limiting high-impact or prolonged moderate-intensity exercise sessions to prevent cartilage damage and guide rehabilitation.
基金the National Natural Science Foundation of China(42074134,42474152,42374150)CNPC Innovation Found(2024DQ02-0152).
文摘The oil-based mud(OBM) borehole measurement environment presents significant limitations on the application of existing electrical logging instruments in high-resistance formations. In this paper, we propose a novel logging method for detection of high-resistance formations in OBM using highfrequency electrodes. The method addresses the issue of shallow depth of investigation(DOI) in existing electrical logging instruments, while simultaneously ensuring the vertical resolution. Based on the principle of current continuity, the total impedance of the loop is obtained by equating the measurement loop to the series form of a capacitively coupled circuit. and its validity is verified in a homogeneous formation model and a radial two-layer formation model with a mud standoff. Then, the instrument operating frequency and electrode system parameters were preferentially determined by numerical simulation, and the effect of mud gap on impedance measurement was investigated. Subsequently, the DOI of the instrument was investigated utilizing the pseudo-geometric factor defined by the real part of impedance. It was determined that the detection depth of the instrument is 8.74 cm, while the effective vertical resolution was not less than 2 cm. Finally, a focused high-frequency electrode-type instrument was designed by introducing a pair of focused electrodes, which effectively enhanced the DOI of the instrument and was successfully deployed in the Oklahoma formation model. The simulation results demonstrate that the novel method can achieve a detection depth of 17.40 cm in highly-resistive formations drilling with OBM, which is approximately twice the depth of detection of the existing oil-based mud microimager instruments. Furthermore, its effective vertical resolution remains at or above 2 cm,which is comparable to the resolution of the existing OBM electrical logging instrument.
文摘Objective:To analyze the significance of high-frequency ultrasound in differentiating benign and malignant breast micronodules.Methods:Eighty-five patients with breast micronodules admitted for diagnosis between October 2022 and October 2024 were selected for high-frequency ultrasound diagnosis.The diagnostic efficacy of high-frequency ultrasound was evaluated by comparing it with the results of surgical pathology.Results:High-frequency ultrasound detected 50 benign nodules,primarily breast fibroadenomas,and 35 malignant nodules,mainly breast ductal carcinoma in situ.Based on surgical pathology results,the diagnostic accuracy of high-frequency ultrasound was 96.47%,specificity was 97.96%,and sensitivity was 94.44%.In high-frequency ultrasound diagnosis,the proportion of grade III and IV blood flow in malignant nodules was higher than that in benign nodules,while the proportion of regular shape and clear margins was lower.The proportion of microcalcifications and posterior echo attenuation was higher in malignant nodules,and the resistance index(RI)and peak blood flow velocity were lower than those in benign nodules(P<0.05).Conclusion:High-frequency ultrasound can effectively differentiate benign and malignant breast micronodules,determine specific nodule types,and exhibits high diagnostic accuracy and sensitivity.Additionally,benign and malignant nodules can be differentiated based on the grading of blood flow signals,sonographic features,and blood flow velocity,providing reasonable guidance for subsequent treatment plans.
基金supported by the science and technology project of State Grid Shanghai Municipal Electric Power Company(No.52094023003L).
文摘New electric power systems characterized by a high proportion of renewable energy and power electronics equipment face significant challenges due to high-frequency(HF)electromagnetic interference from the high-speed switching of power converters.To address this situation,this paper offers an in-depth review of HF interference problems and challenges originating from power electronic devices.First,the root cause of HF electromagnetic interference,i.e.,the resonant response of the parasitic parameters of the system to high-speed switching transients,is analyzed,and various scenarios of HF interference in power systems are highlighted.Next,the types of HF interference are summarized,with a focus on common-mode interference in grounding systems.This paper thoroughly reviews and compares various suppression methods for conducted HF interference.Finally,the challenges involved and suggestions for addressing emerging HF interference problems from the perspective of both power electronics equipment and power systems are discussed.This review aims to offer a structured understanding of HF interference problems and their suppression techniques for researchers and practitioners.
文摘Objective:To analyze the therapeutic effect of high-frequency electrosurgical knife surgery guided by painless digestive endoscopy(PDE)in elderly patients with gastrointestinal polyps(GP).Methods:A total of 100 elderly GP patients admitted between June 2021 and December 2022 were selected.Patients were randomly divided into two groups:the painless group(50 cases)underwent high-frequency electrosurgical knife surgery guided by PDE,while the conventional group(50 cases)underwent the same surgery guided by traditional digestive endoscopy(DE).The total treatment efficacy,perioperative indicators,gastrointestinal hormone levels,oxidative stress(OS)markers,and complication rates were compared between the two groups.Results:The total treatment efficacy in the painless group was higher than that in the conventional group,and perioperative indicators were superior in the painless group(P<0.05).One week after treatment,the gastrointestinal hormone levels and OS-related markers in the painless group were better than those in the conventional group(P<0.05).The complication rate in the painless group was lower than in the conventional group(P<0.05).Conclusion:High-frequency electrosurgical knife surgery guided by PDE improves the effectiveness of polyp removal in elderly GP patients and accelerates postoperative recovery.It also protects gastrointestinal function,reduces postoperative OS,and ensures higher surgical safety.
基金supported by the National Science Foundation of China(No.12127806,No.62175195 and No.12304382)the International Joint Research Laboratory for Micro/Nano Manufacturing and Measurement Technologies.
文摘Single-shot ultrafast compressed imaging(UCI)is an effective tool for studying ultrafast dynamics in physics,chemistry,or material science because of its excellent high frame rate and large frame number.However,the random code(Rcode)used in traditional UCI will lead to low-frequency noise covering high-frequency information due to its uneven sampling interval,which is a great challenge in the fidelity of large-frame reconstruction.Here,a high-frequency enhanced compressed active photography(H-CAP)is proposed.By uniformizing the sampling interval of R-code,H-CAP capture the ultrafast process with a random uniform sampling mode.This sampling mode makes the high-frequency sampling energy dominant,which greatly suppresses the low-frequency noise blurring caused by R-code and achieves high-frequency information of image enhanced.The superior dynamic performance and large-frame reconstruction ability of H-CAP are verified by imaging optical self-focusing effect and static object,respectively.We applied H-CAP to the spatial-temporal characterization of double-pulse induced silicon surface ablation dynamics,which is performed within 220 frames in a single-shot of 300 ps.H-CAP provides a high-fidelity imaging method for observing ultrafast unrepeatable dynamic processes with large frames.
基金supported by the National Key R&D Program of China(Grant No.2021YFB3501300)the 9th Research Institute of China Electronics Technology Group Corporation’s open projects(Grant No.2024SK-002-01)the Science and Technology Project of Gansu Province(Grant No.22YF7GA001).
文摘Soft magnetic composites made from metallic magnetic particles with an easy magnetization plane(referred to as easy-plane metallic soft magnetic composites(SMC))are considered ideal materials for the next generation of power electronic devices.This advantage is attributed to their ability to maintain high permeability at elevated frequencies.Despite these advantages,a definitive mathematical model that connects the high-frequency magnetic properties(e.g.,effective permeability)of easy-plane metallic SMCs to the intrinsic properties of the particles is still lacking.In this work,a theoretical calculation model for the effective permeability of easy-plane metallic SMCs was formulated.This model was derived from a skin effect-corrected Landau-Lifshitz-Gilbert(LLG)equation and integrated with effective medium theory incorporating inter-particle interaction.To validate the model,we prepared samples of easy-plane Y_(2)Co_(17)particle/PU SMCs with varying particle sizes and volume fractions.The experimental results showed a strong agreement with the calculated values.This research offers critical theoretical backing for the design and optimization of soft magnetic materials intended for high-frequency applications.
基金supported by the Commercial Aircraft Corporation of China Ltd.(Grant No.COMAC-SFGS-2024–569)Fundamental Research Funds for the Central Universities and Institute of Marine Equipment,Shanghai Rising-Star Program of Science and Technology Commission of Shanghai Municipality(Grant No.23QA1404700)+1 种基金National Natural Science Foundation of China(Grant No.52475384,52505409)China Postdoctoral Science Foundation(Grant No.2024M761963)。
文摘High-frequency pulsed(HFP)gas tungsten arc welding(GTAW)has shown excellent performance in welding of aluminum alloys in recent years,which makes itself a promisingly potential technique for part manufacturing in aviation industry.However,existing researches generally focuses on the effect of a single parameter while lacks multivariable researches.Considering of the fact that gap and misalignment are inevitable in real part clamping,adaptive intelligent welding is usually used during automatic manufacturing,which means under the control of filler wire amount per length of a weld,other parameters including current,welding speed and wire feed speed during one single weld are changing according to the specific clamping situation.Therefore,the influence of specific energy input led by different welding parameters within one adaptive welding program on microstructure and mechanical property of the weld needs to be clarified.This study investigates the effect of welding heat input(ranging from 1048.3 J/mm to 825.6 J/mm within one adaptive welding program control)on the formation quality of 3.25 mm thick 6061 aluminum alloy joints fabricated by HFP-GTAW with 4043 filler wire.According to the obtained results,non-monotonic relationship between heat input and porosity,with an optimal minimum of 4.92%achieved at an intermediate heat input of 856.8 J/mm.The 21.2%decrease of energy input during welding process would reduce the average grain size in the weld center and adjacent to fusion line by 18.6%and 19.4%,respectively.The ratios between fluctuation range to minimum value in average yield and the relative ranges of yield strength and ultimate tensile strength across the tested heat inputs were 14.7%and 12.7%,respectively.The findings provide a general overview on how the microstructure and mechanical properties would fluctuate in an adaptively controlled HFP-GTAW fabricated aluminum alloy weld.
基金National Natural Science Foundation of China, grant number 52177074.
文摘With the evolution of DC distribution networks from traditional radial topologies to more complex multi-branch structures,the number of measurement points supporting synchronous communication remains relatively limited.This poses challenges for conventional fault distance estimation methods,which are often tailored to simple topologies and are thus difficult to apply to large-scale,multi-node DC networks.To address this,a fault distance estimation method based on sparse measurement of high-frequency electrical quantities is proposed in this paper.First,a preliminary fault line identification model based on compressed sensing is constructed to effectively narrow the fault search range and improve localization efficiency.Then,leveraging the high-frequency impedance characteristics and the voltage-current relationship of electrical quantities,a fault distance estimation approach based on high-frequency measurements from both ends of a line is designed.This enables accurate distance estimation even when the measurement devices are not directly placed at both ends of the faulted line,overcoming the dependence on specific sensor placement inherent in traditional methods.Finally,to further enhance accuracy,an optimization model based on minimizing the high-frequency voltage error at the fault point is introduced to reduce estimation error.Simulation results demonstrate that the proposed method achieves a fault distance estimation error of less than 1%under normal conditions,and maintains good performance even under adverse scenarios.
基金supported by the Project of the National Key Research and Development Program of China under Grant 2022YFB2404100。
文摘The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model for epoxy resin encapsulated nano HFTs, which aims to precisely predict the temperature distribution inside the transformer in combination with the finite element method(FEM). A magnetothermal bidirectional coupling 3DTN model is established by analyzing the thermal conduction between the core, windings, and epoxy resin, while also considering the convection and radiation heat transfer mechanisms on the surface of the epoxy resin. The model considers the impact of loss distribution in the core and windings on the temperature field and adopts a simplified 1/2 thermal network model to reduce computational complexity. Furthermore, the results of FEM are compared with experimental results to verify the accuracy of the 3DTN model in predicting the temperature rise of nano HFT. The results show that the 3DTN model reduces errors by an average of 5.25% over the traditional two-dimensional thermal network(2DTN) model, particularly for temperature distributions in the windings and core. This paper provides a temperature rise prediction method for the thermal design and offers a theoretical basis and engineering guidance for the optimization of their thermal management systems.
基金supported by the project Major Scientific and Technological Special Project of Guizhou Province([2024]014).
文摘Load frequency control(LFC)is a critical function to balance the power consumption and generation.Thegrid frequency is a crucial indicator for maintaining balance.However,the widely used information and communication infrastructure for LFC increases the risk of being attacked by malicious actors.The dynamic load altering attack(DLAA)is a typical attack that can destabilize the power system,causing the grid frequency to deviate fromits nominal value.Therefore,in this paper,we mathematically analyze the impact of DLAA on the stability of the grid frequency and propose the network parameter regulation(NPR)to mitigate the impact.To begin with,the dynamic LFC model is constructed by highlighting the importance of the network parameter.Then,we model the DLAA and analyze its impact on LFC using the theory of second-order dynamic systems.Finally,we model the NPR and prove its effect in mitigating the DLAA.Besides,we construct a least-effort NPR considering its infrastructure cost and aim to reduce the operation cost.Finally,we carry out extensive simulations to demonstrate the impact of the DLAA and evaluate the mitigation performance of NPR.The proposed cost-benefit NPR approach can not only mitigate the impact of DLAA with 100%and also save 41.18$/MWh in terms of the operation cost.
文摘This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and the stress and aerodynamic load measurement points are reasonably arranged accordingly.The actual measurement is carried out in combination with the operating conditions of the existing lines.The stress variations and spectral characteristics of the train under different speed levels(80,160,180,200 km/h),tunnel entry and exit,and scraper action conditions were compared and analyzed.The stress amplification factors under tunnel intersection and scraper action were obtained,providing boundary conditions for the design of wipers for highspeed s.The research results show that the maximum stress of the wiper structure obtained through simulation calculation is concentrated at the connection of the wiper arm.Structural stress increases with the rise of speed grade.The stress increases by 1.11 times when the tunnel meets.When the scraper operates,the stress on the scraper arm increases by 4.1–7.6 times.Due to the broadband excitation effect of the aerodynamic load,the spectral energy of the structure is relatively high at the natural frequency,which excites the natural mode of the wiper.
