The Fe-based coating was produced on the surface of the column substrate with a Al2O3 cylindrical sleeve by high frequency induction cladding, microstructure of the coating was investigated with scanning electron micr...The Fe-based coating was produced on the surface of the column substrate with a Al2O3 cylindrical sleeve by high frequency induction cladding, microstructure of the coating was investigated with scanning electron microscope (SEM), the crystal structure was characterized by X-ray diffractometer (XRD), the microhardness and wear resisitance of the coating were evaluated. The results show that a metallurgical bond between coating and substrate was obtained during the rapid solidification, the phases of the coating were composed of austenite and the eutectic of γ-Fe + (Cr, Fe)7(C, B)3. Compared with the substrate, the microhardness and wear resistance of the coating improved apparently, solid-solution strengthening and second-phase particle hardening led to these results.展开更多
The evolution of temperature field of the continual motion induction cladding and the depth of heat affected zone are studied in this study.A three-dimensional finite element model for the point type continual inducti...The evolution of temperature field of the continual motion induction cladding and the depth of heat affected zone are studied in this study.A three-dimensional finite element model for the point type continual induction cladding is established to investigate temperature distributions of fixed and motion induction cladding modes.The novel inductor is designed for cladding of curved surfaces.The modeling reliability is verified by the temperature measurements.The influence of process parameters on the maximum temperature and the generation and transfer of heat are studied.Quantitative calculation is performed to its melting rate to verify the temperature distribution and microstructures.The results show that a good metallurgical bond can be formed between the cladding layer and substrate.The melting rate gradually falls from the top of the cladding layer to the substrate,and the grain size in the substrate gradually rises.The heat affected zone is relatively small compared to integral heating.展开更多
Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature dis...Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature distribution in the induction brazing model. The in?uences of induction brazing parameters on the residual stresses of polycrystalline CBN abrasive grits have been analyzed, including the embedding depth, grit side length, etc. Results obtained show that the tensile stress with a 40% embedding depth is 292 MPa, which is the minimum on the bonding interface compared with other embedding depths. Meanwhile, the maximum tensile stress is 575 MPa, with an increase of 59% compared with that of a grit side length of 50 mm. Finally, the simulation results of the brazing residual stress of polycrystalline CBN abrasive grits have been con?rmed valid based on the residual stress measurement of the brazed monocrystalline CBN grit.展开更多
To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser...To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.展开更多
Process and mechanism of high frequency were studied in this paper by means of cold attachment for the preparation of GNi WC25 coating . The results show its special distribution law of eddy current while the magnetic...Process and mechanism of high frequency were studied in this paper by means of cold attachment for the preparation of GNi WC25 coating . The results show its special distribution law of eddy current while the magnetic transition temperature and electric resistivity of the coating have been measured .Wear resistance of the high frequency induction coating has an advantage over those of laser cladding coating and oxygen acetylene spraying fusing coating . Moreover , the GNi WC25 coating by high frequency induction cladding has smooth surface and even microstructure.展开更多
The microhardness of piston rods treated with different induction hardening processes was tested. The experimental results reveal that the depth of the hardened zone is proportional to the ratio of the moving speed of...The microhardness of piston rods treated with different induction hardening processes was tested. The experimental results reveal that the depth of the hardened zone is proportional to the ratio of the moving speed of the piston rod to the output power of the induction generator. This result is proved correct through the Finite Element Method (FEM) simulation of the thermal field of induction heating. From tensile and impact tests, an optimized high frequency induction hardening process for piston rods has been obtained, where the output power was 82%×80 kW and the moving speed of workpiece was 5364 mm/min. The piston rods, treated by the optimized high frequency induction hardening process, show the best comprehensive mechanical performance.展开更多
For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted...For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted into cylindrical clay,the increase in temperature(Δ7)was 31.2℃ for the specimen with a 1.5 mm diameter,while the 1.0mm diameter specimen exhibited a ΔT value of 15.7℃ after the induction time of 1200s.The ΔT exhibited a high value of 57.9℃ during the simultaneous insertion of 3 1.5mm diameter specimens.In the computer simulation images, the relatively lower magnetic flux density and concurrent neghgibly low current density were observed from the surface to the internal regions,being different from the behavior of a ferromagnetic Ni-rod with the same size.展开更多
In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction he...In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.展开更多
Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and cer...Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating： one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.展开更多
Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve th...Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve their quality due to joint action of superficial effects and electromagnetic forces.For all magnetic materials is nonlinear decrease in heating power depending on frequency of HF.Installed the optimal parameters of HF heating for soldering electronics modules by inductor with open-ended magnetic conductor.展开更多
The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF...The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF modeling method,which has the merits of high accuracy,good versatility,and simple parameterization,is proposed.The proposed model of the induction motor consists of a three-phase equivalent circuit with eighteen circuit elements per phase to ensure model accuracy.The per phase circuit structure is symmetric concerning its phase-start and phase-end points.This symmetry enables the proposed model to be applicable for both star-and delta-connected induction motors without having to recalculate the circuit element values when changing the motor connection from star to delta and vice versa.Motor physics knowledge,namely per-phase impedances,are used in the artificial neural network to obtain the values of the circuit elements.The parameterization can be easily implemented within a few minutes using a common personal computer(PC).Case studies verify the effectiveness of the proposed HF modeling method.展开更多
The mutual impedance between doubly-fed induction generator(DFIG)system and weak grid may cause a resonance,which yields to undesirable distortions and harmonics.The equivalent impedance of DFIG systems is high,which ...The mutual impedance between doubly-fed induction generator(DFIG)system and weak grid may cause a resonance,which yields to undesirable distortions and harmonics.The equivalent impedance of DFIG systems is high,which creates high-frequency resonance(HFR)in interaction with weak grids.Although several studies are conducted to mitigate HFRs,more improvements are needed in terms of damping and phasemargin.Accordingly,an active damping control strategy based on virtual admittance is proposed,which properly mitigates the disturbances.The proposed strategy is accurate as it considers the dynamic high-frequency model of DFIG system to effectively reduce the HFR.The performance of the proposed strategy is verified by using different case studies on a 2 MW DFIG system with time-domain simulations in MATLAB/Simulink environment.展开更多
文摘The Fe-based coating was produced on the surface of the column substrate with a Al2O3 cylindrical sleeve by high frequency induction cladding, microstructure of the coating was investigated with scanning electron microscope (SEM), the crystal structure was characterized by X-ray diffractometer (XRD), the microhardness and wear resisitance of the coating were evaluated. The results show that a metallurgical bond between coating and substrate was obtained during the rapid solidification, the phases of the coating were composed of austenite and the eutectic of γ-Fe + (Cr, Fe)7(C, B)3. Compared with the substrate, the microhardness and wear resistance of the coating improved apparently, solid-solution strengthening and second-phase particle hardening led to these results.
基金Project(51575415)supported by the National Natural Science Foundation of ChinaProject(2016CFA077)supported by the Natural Science Foundation of Hubei Province of ChinaProject(2018-YS-026)supported by the Excellent Dissertation Cultivation Funds of Wuhan University of Technology,China。
文摘The evolution of temperature field of the continual motion induction cladding and the depth of heat affected zone are studied in this study.A three-dimensional finite element model for the point type continual induction cladding is established to investigate temperature distributions of fixed and motion induction cladding modes.The novel inductor is designed for cladding of curved surfaces.The modeling reliability is verified by the temperature measurements.The influence of process parameters on the maximum temperature and the generation and transfer of heat are studied.Quantitative calculation is performed to its melting rate to verify the temperature distribution and microstructures.The results show that a good metallurgical bond can be formed between the cladding layer and substrate.The melting rate gradually falls from the top of the cladding layer to the substrate,and the grain size in the substrate gradually rises.The heat affected zone is relatively small compared to integral heating.
基金supported by the National Natural Science Foundation of China(No.51775275)the Fundamental Research Funds for the Central Universities(No.NE2014103 and No.NZ2016107)
文摘Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature distribution in the induction brazing model. The in?uences of induction brazing parameters on the residual stresses of polycrystalline CBN abrasive grits have been analyzed, including the embedding depth, grit side length, etc. Results obtained show that the tensile stress with a 40% embedding depth is 292 MPa, which is the minimum on the bonding interface compared with other embedding depths. Meanwhile, the maximum tensile stress is 575 MPa, with an increase of 59% compared with that of a grit side length of 50 mm. Finally, the simulation results of the brazing residual stress of polycrystalline CBN abrasive grits have been con?rmed valid based on the residual stress measurement of the brazed monocrystalline CBN grit.
基金Projects(51471084,61475117)supported by the National Natural Science Foundation of ChinaProject(13ZCZDGX01109)supported by Tianjin Municipal Science and Technology Commission of ChinaProject(20122BBE500031)supported by the Key Technology Project of Jiangxi Province in China
文摘To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.
文摘Process and mechanism of high frequency were studied in this paper by means of cold attachment for the preparation of GNi WC25 coating . The results show its special distribution law of eddy current while the magnetic transition temperature and electric resistivity of the coating have been measured .Wear resistance of the high frequency induction coating has an advantage over those of laser cladding coating and oxygen acetylene spraying fusing coating . Moreover , the GNi WC25 coating by high frequency induction cladding has smooth surface and even microstructure.
文摘The microhardness of piston rods treated with different induction hardening processes was tested. The experimental results reveal that the depth of the hardened zone is proportional to the ratio of the moving speed of the piston rod to the output power of the induction generator. This result is proved correct through the Finite Element Method (FEM) simulation of the thermal field of induction heating. From tensile and impact tests, an optimized high frequency induction hardening process for piston rods has been obtained, where the output power was 82%×80 kW and the moving speed of workpiece was 5364 mm/min. The piston rods, treated by the optimized high frequency induction hardening process, show the best comprehensive mechanical performance.
基金Item Sponsored by a Grant-in-Aid from Ministry of Education,Science,Sports and Culture of Japan[No.23500559:Naohara T]
文摘For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted into cylindrical clay,the increase in temperature(Δ7)was 31.2℃ for the specimen with a 1.5 mm diameter,while the 1.0mm diameter specimen exhibited a ΔT value of 15.7℃ after the induction time of 1200s.The ΔT exhibited a high value of 57.9℃ during the simultaneous insertion of 3 1.5mm diameter specimens.In the computer simulation images, the relatively lower magnetic flux density and concurrent neghgibly low current density were observed from the surface to the internal regions,being different from the behavior of a ferromagnetic Ni-rod with the same size.
基金financially supported by the National Natural Science Foundation of China(Nos.51235004 and51375235)the Fundamental Research Funds for the Central Universities(No.NE2014103)the Funding for Outstanding Doctoral Dissertation in NUAA(No.BCXJ16-06)
文摘In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.
基金Project (59975046) supported by the National Natural Science Foundation of China
文摘Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating： one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.
文摘Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve their quality due to joint action of superficial effects and electromagnetic forces.For all magnetic materials is nonlinear decrease in heating power depending on frequency of HF.Installed the optimal parameters of HF heating for soldering electronics modules by inductor with open-ended magnetic conductor.
文摘The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF modeling method,which has the merits of high accuracy,good versatility,and simple parameterization,is proposed.The proposed model of the induction motor consists of a three-phase equivalent circuit with eighteen circuit elements per phase to ensure model accuracy.The per phase circuit structure is symmetric concerning its phase-start and phase-end points.This symmetry enables the proposed model to be applicable for both star-and delta-connected induction motors without having to recalculate the circuit element values when changing the motor connection from star to delta and vice versa.Motor physics knowledge,namely per-phase impedances,are used in the artificial neural network to obtain the values of the circuit elements.The parameterization can be easily implemented within a few minutes using a common personal computer(PC).Case studies verify the effectiveness of the proposed HF modeling method.
文摘The mutual impedance between doubly-fed induction generator(DFIG)system and weak grid may cause a resonance,which yields to undesirable distortions and harmonics.The equivalent impedance of DFIG systems is high,which creates high-frequency resonance(HFR)in interaction with weak grids.Although several studies are conducted to mitigate HFRs,more improvements are needed in terms of damping and phasemargin.Accordingly,an active damping control strategy based on virtual admittance is proposed,which properly mitigates the disturbances.The proposed strategy is accurate as it considers the dynamic high-frequency model of DFIG system to effectively reduce the HFR.The performance of the proposed strategy is verified by using different case studies on a 2 MW DFIG system with time-domain simulations in MATLAB/Simulink environment.
