WC particles reinforced CoCrFeNiMo high-entropy alloy(HEA)composite coatings were prepared on Cr12MoV steel successfully by laser cladding technology to improve the wear resistance of substrates.Effect of WC content o...WC particles reinforced CoCrFeNiMo high-entropy alloy(HEA)composite coatings were prepared on Cr12MoV steel successfully by laser cladding technology to improve the wear resistance of substrates.Effect of WC content on microstructure and wear property of the composite coatings was studied in detail.Large numbers of carbides with four main types:primary carbide crystals,eutectic structures,massive crystals growing along the periphery of the remaining WC particles and incompletely fused WC particles,were found to exist in the WC/CoCrFeNiMo composite coatings.With increasing WC content,the microhardness of coatings is gradually improved while the average friction coefficients follow the opposite trend due to solid solution strengthening and second phase strengthening effect.The maximum microhardness and minimum friction coefficient are HV_(0.2)689.7 and 0.72,respectively,for the composite coating with 30 wt.%WC,the wear resistance of the substrate is improved significantly,the wear mechanisms are spalling wear and abrasive wear due to their high microhardness.展开更多
Polybrominated biphenyl ethers(PBDEs)and polycyclic aromatic hydrocarbons(PAHs)are commonly detected contaminants at e-waste recycling sites.Against the conventional wisdom that PBDEs and PAHs are highly immobile and ...Polybrominated biphenyl ethers(PBDEs)and polycyclic aromatic hydrocarbons(PAHs)are commonly detected contaminants at e-waste recycling sites.Against the conventional wisdom that PBDEs and PAHs are highly immobile and persist primarily in shallowsurface soils,increasing evidence shows that these compounds can leach into the groundwater.Herein,we compare the leachabilities of PBDEs vs.PAHs from contaminated soils collected at an e-waste recycling site in Tianjin,China.Considerable amounts of BDE-209(0.3–2 ng/L)and phenanthrene(42–106 ng/L),the most abundant PBDE and PAH at the site,are detected in the effluents of columns packed with contaminated soils,with the specific concentrations varying with hydrodynamic and solution chemistry conditions.Interestingly,the leaching potential of BDE-209 appears to be closely related to the release of colloidal mineral particles,whereas the leachability of phenanthrene correlates well with the concentration of dissolved organic carbon in the effluent,but showing essentially no correlation with the concentration of mineral particles.The surprisingly different trends of the leachability observed between BDE-209 and phenanthrene is counterintuitive,as PBDEs and PAHs often co-exist at e-waste recycling sites(particularly at the sites wherein incineration is being practiced)and share many similarities in terms of physicochemical properties.One possible explanation is that due to its extremely low solubility,BDE-209 predominantly exists in free-phase(i.e.,as solid(nano)particles),whereas the more soluble phenanthrene is mainly sorbed to soil organic matter.Findings in this study underscore the need to better understand the mobility of highly hydrophobic organic contaminants at contaminated sites for improved risk management.展开更多
Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid ...Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.展开更多
Biocompatible amphiphilic nanoparticles(NPs)with tunable particle morphology and surface property are important for their applications as functional materials.However,previously developed methods to prepare amphiphili...Biocompatible amphiphilic nanoparticles(NPs)with tunable particle morphology and surface property are important for their applications as functional materials.However,previously developed methods to prepare amphiphilic NPs generally involve several steps,especially an additional step for surface modification,greatly hindering their largescale production and widespread applications.Here,a versatile one-step strategy is developed to prepare biocompatible amphiphilic dimer NPs with tunable particle morphology and surface property.The amphiphilic dimer NPs,which consist of a hydrophobic shellac bulb and a hydrophilic poly(lactic acid)(PLA)bulb with PLA-poly(ethylene glycol)(PEG)on the bulb surface,are prepared in a single step by controlled co-precipitation and self-assembly.Amphiphilic PLA-PEG/shellac dimer NPs demonstrate excellent tunability in particle morphology,thus showing good performances in controlling the interfacial curvature and emulsion type.In addition,temperatureresponsive PLA-poly(N-isopropyl acrylamide)(PNIPAM)/shellac dimer NPs are prepared following the same method and emulsions stabilized by them show temperature-triggered response.The applications of PLA-PEG-folic acid(FA)/shellac dimer NPs for drug delivery have also been demonstrated,which show a very good performance.The strategy of preparing the dimer NPs is green,scalable,facile and versatile,which provides a good platform for the design of dimer NPs with tunable particle morphology and surface property for diverse applications.展开更多
We review a 3d quantum gravity model, which incorporates massive spinning fields into the Euclidean path integral in a Chern-Simons formulation. Fundamental matter as defined in our previous preon model is recapped. B...We review a 3d quantum gravity model, which incorporates massive spinning fields into the Euclidean path integral in a Chern-Simons formulation. Fundamental matter as defined in our previous preon model is recapped. Both quantum gravity and the particle model are shown to be derivable from the supersymmetric 3d Chern-Simons action. Forces-Matter unification is achieved.展开更多
Metal-support interactions and hydrogen spillover effects in heterogeneous catalysts play a crucial role in aromatic hydrogenation reactions;however,these effects are limited by the metal dispersion on the catalyst an...Metal-support interactions and hydrogen spillover effects in heterogeneous catalysts play a crucial role in aromatic hydrogenation reactions;however,these effects are limited by the metal dispersion on the catalyst and the number of acceptable H*receptors.This study prepares highly dispersed Ni nanoparticles(NPs)catalysts on a Beta substrate via precursor structure topology transformation.In contrast to traditional support materials,the coordination and electronic structure changes between the Ni NPs and the support were achieved,further optimizing the active interface sites and enhancing hydrogen activation and hydrogenation performance.Additionally,the-OH groups at the strong acid sites in zeolite effectively intensified the hydrogen spillover effect as receptors for H^(*)migration and anchoring,accelerating the hydrogenation rate of aromatic rings.Under solvent-free conditions,this catalyst was used for the hydrogenation reaction of aromatic-rich oils,directly producing a C_(8)-C_(14)branched cycloalkanes mixture with an aromatic conversion rate of>99%.The cycloalkanes mixture produced by this method features high density(0.92 g/mL)and a low freezing point(<-60℃),making it suitable for use as high-density aviation fuel or as an additive to enhance the volumetric heat value of conventional aviation fuels in practical applications.展开更多
In rotationally extruded fittings,high-density polyethylene(HDPE)pipes prepared using conventional processing methods often suffer from poor pressure resistance and low toughness.This study introduces an innovative ro...In rotationally extruded fittings,high-density polyethylene(HDPE)pipes prepared using conventional processing methods often suffer from poor pressure resistance and low toughness.This study introduces an innovative rotary shear system(RSS)to address these deficiencies through controlled mandrel rotation and cooling rates.We successfully prepared self-reinforced HDPE pipes with a three-layer structure combining spherical and shish-kebab crystals.Rotational processing aligned the molecular chains in the ring direction and formed shish-kebab crystals.As a result,the annular tensile strength of the rotationally processed three-layer shish-kebab structure(TSK)pipe increased from 26.7 MPa to 76.3 MPa,an enhancement of 185.8%.Notably,while maintaining excellent tensile strength(73.4 MPa),the elongation at break of the spherulite shishkebab spherulite(SKS)tubes was improved to 50.1%,as compared to 33.8%in the case of shish-kebab spherulite shish-kebab(KSK)tubes.This improvement can be attributed to the changes in the micro-morphology and polymer structure within the SKS tubes,specifically due to the formation of small-sized shish-kebab crystals and the low degrees of interlocking.In addition,2D-SAXS analysis revealed that KSK tubes have higher tensile strength due to smaller crystal sizes and larger shish dimensions,forming dense interlocking structures.In contrast,the SKS and TSK tubes had thicker amorphous regions and smaller shish sizes,resulting in reduced interlocking and mechanical performance.展开更多
Studying the contribution of regional transport to ultrafine particles(UFPs)and the deposition effect of nanoscale particles in human respiratory system is conducive to exploring the impact of atmospheric particles on...Studying the contribution of regional transport to ultrafine particles(UFPs)and the deposition effect of nanoscale particles in human respiratory system is conducive to exploring the impact of atmospheric particles on the environment and human health.Based on the data set of number concentration spectrum in the particle size range of 5.6–560 nm in the spring of Hefei,the Yangtze River Delta region obtained by a fast mobility particle sizer,the explosive growth characteristics,potential source identification and deposition flux analysis of UFPs were systematically studied.The results showed that the frequency of new particle formation(NPF)events during spring was 31.5%.SO_(2) and O_(3) contribute to NPF events.Daytime,higher temperature,stronger solar radiation and lower humidity were more conducive to the explosive growth of UFPs.In addition,regional transport of pollutants from the cities around Hefei played an important role in the accumulation mode particles,which were mainly affected by the land-source air mass from northwest Jiangsu(23.64%)and the sea-source air mass from the Yellow Sea(23.99%).It was worth noting that approximately 10,406 ng of UFPs enters the human respiratory system every day.Themain deposition area of 5.6–560 nm nanoscale particles was alveolar,5.6–400 nm is more likely to be deposited on alveolar,while nanoscale particles with particle size between 400 and 560 nm is more likely to be deposited on head airways.This study identified the deposition risk of nanoscale particles in the respiratory system under different particle sizes.展开更多
Aerosol particle pollution has become an increasing serious environmental problem,and urban vegetation plays a long-lasting and positive role in mitigating it.This study compared the particle capture abilities of tree...Aerosol particle pollution has become an increasing serious environmental problem,and urban vegetation plays a long-lasting and positive role in mitigating it.This study compared the particle capture abilities of trees,shrubs,and herbs,and examined the compositions and influence of aerosol particles accumulated on leaf functional traits.Retained particles primarily contained Ca^(2+),K^(+),SO_(4)^(2-),NO_(3)^(-)and NH_(4)^(+),indicating their anthropogenic origins.The leathery-leaved tree Osmanthus fragrans and the papery-leaved herb Alternanthera sessilis demonstrated the higher competence in particle accumulation than other plants,and leaf morphologic structures(e.g.,leaf grooves,trichomes,waxy layers,and stomata characteristics)were closely associated with particle capture by plant species.Particle retention negatively impacted stomata,impeding photosynthesis,and reducing transpiration.In response to particle accumulation,plants tended to decrease specific leaf area and adjust stomatal conductance.Both growth form and leaf texture significantly influenced the particle capture abilities of different plant species.The substantial contribution of plants,particularly herbs in the lower vegetation strata,to particle removal should not be overlooked.Vegetation with a tree-shrub-herb configuration excels at particle capture,offering potential advantages in mitigating particle pollution and enhancing ecological benefits.展开更多
High-density interconnect(HDI)soft electronics that can integrate multiple individual functions into one miniaturized monolithic system is promising for applications related to smart healthcare,soft robotics,and human...High-density interconnect(HDI)soft electronics that can integrate multiple individual functions into one miniaturized monolithic system is promising for applications related to smart healthcare,soft robotics,and human-machine interactions.However,despite the recent advances,the development of three-dimensional(3D)soft electronics with both high resolution and high integration is still challenging because of the lack of efficient manufacturing methods to guarantee interlayer alignment of the high-density vias and reliable interlayer electrical conductivity.Here,an advanced 3D laser printing pathway,based on femtosecond laser direct writing(FLDW),is demonstrated for preparing liquid metal(LM)-based any layer HDI soft electronics.FLDW technology,with the characteristics of high spatial resolution and high precision,allows the maskless fabrication of high-resolution embedded LM microchannels and high-density vertical interconnect accesses for 3D integrated circuits.High-aspect-ratio blind/through LM microstructures are formed inside the elastomer due to the supermetalphobicity induced during laser ablation.The LM-based HDI circuit featuring high resolution(~1.5μm)and high integration(10-layer electrical interconnection)is achieved for customized soft electronics,including various customized multilayer passive electric components,soft multilayer circuit,and cross-scale multimode sensors.The 3D laser printing method provides a versatile approach for developing chip-level soft electronics.展开更多
Dislocation strengthening,as one of the methods to simultaneously enhance the room temperature strength and ductility of alloys,does not achieve the desired strengthening and plasticity effect during elevated-temperat...Dislocation strengthening,as one of the methods to simultaneously enhance the room temperature strength and ductility of alloys,does not achieve the desired strengthening and plasticity effect during elevated-temperature deformation.Here,we report a novel strategy to boost the dislocation multiplication and accumulation during deformation at elevated temperatures through dynamic strain aging(DSA).With the introduction of the rare-earth element Ho in Mg-Y-Zn alloy,Ho atoms diffuse toward dislocations during deformation at elevated temperatures,provoking the DSA effect,which increases the dislocation density significantly via the interactions of mobile dislocations and Ho atoms.The resulting alloy achieves a great enhancement of dislocation hardening and obtains the dual benefits of high strength and good ductility simultaneously at high homologous temperatures.The present work provides an effective strategy to enhancing the strength and ductility for elevated-temperature materials.展开更多
The effect of intermetallic particles on the corrosion of 6061 aluminum alloy and its coating used in semiconductor processing systems was systematically studied via liquid and gas experiments and micromorphology char...The effect of intermetallic particles on the corrosion of 6061 aluminum alloy and its coating used in semiconductor processing systems was systematically studied via liquid and gas experiments and micromorphology characterization.The results revealed that a huge difference of corrosion resistance between imported and domestic 6061 aluminum alloys in HCl solution and gas acid mist experiments mainly was attributed to the different size and amount of Al_(15)(Fe,Mn)_(3)Si_(2).The corrosion resistance of domestic 6061 alloy in dry/wet semiconductor electronic special gas environments was worse than that of imported aluminum alloy,and there are great differences in the corrosion mechanism of 6061 alloy caused by the second phase in the two dry/wet environments.And the corrosion resistance of the hard anodized alumina film was closely related to the microscopic morphology of holes.The vertical and elongatedα-Al_(15)(Mn,Fe)_(3)Si_(2) phase was formed in the rolled aluminum alloy that has been rolled perpendicular to the surface of the substrate.Compared to the horizontal long hole,the longitudinal long holes generated by the verticalα-Al_(15)(Mn,Fe)_(3)Si_(2) phase will enable the corrosive medium to reach the substrate rapidly,which significantly weakens the corrosion resistance of the hard anodized film.展开更多
The Feynman ratchet has the ability to convert random fluctuations into directional particle transport.The transport velocity of particles is highly dependent on their size,leading to directional transport and subsequ...The Feynman ratchet has the ability to convert random fluctuations into directional particle transport.The transport velocity of particles is highly dependent on their size,leading to directional transport and subsequent particle separation under suitable parameter conditions.Here,exploiting the distinct responses of particles with different sizes to the system,the separation of bi-dispersed dust particles is achieved experimentally in air at 35 Pa using a dusty plasma ratchet.To reveal the underlying mechanisms,we construct a plasma model and perform Langevin simulations for the particle separation.Our numerical results reveal that charged dust particles experience an asymmetric ratchet potential,which dictates their directional transport.Crucially,bi-dispersed dust particles are suspended at different heights and are subject to ratchet potentials with opposing asymmetries,resulting in their separation.These findings may offer new perspectives for related fields,including microfluidics,nanotechnology,and micrometer-scale particle manipulation.展开更多
Triboelectric nanogenerators(TENGs)are emerging as new technologies to harvest electrical power from mechanical energy.With the distinctive working mechanism of triboelectric nanogenerators,they attract particular int...Triboelectric nanogenerators(TENGs)are emerging as new technologies to harvest electrical power from mechanical energy.With the distinctive working mechanism of triboelectric nanogenerators,they attract particular interest in healthcare monitoring,wearable electronics,and deformable energy harvesting,which raises the requirement for highly conformable devices with substantial energy outputs.Here,a simple,low-cost strategy for fabricating stretchable triboelectric nanogenerators with ultra-high electrical output is developed.The TENG is prepared using PTFE micron particles(PPTENG),contributing a different electrostatic induction process compared to TENG based on dielectric films,which was associated with the dynamics of particle motions in PP-TENG.The generator achieved an impressive voltage output of 1000 V with a current of 25 lA over a contact area of 40320 mm^(2).Additionally,the TENG exhibits excellent durability with a stretching strain of 500%,and the electrical output performance does not show any significant degradation even after 3000 cycles at a strain of 400%.The unique design of the device provides high conformability and can be used as a self-powered sensor for human motion detection.展开更多
Rapeseed mustard(Brassica juncea L.) is the third most important oilseed crop in the world, but the geneticmechanism underlying its massive phenotypic variation remains largely unexplored. In this study, specific leng...Rapeseed mustard(Brassica juncea L.) is the third most important oilseed crop in the world, but the geneticmechanism underlying its massive phenotypic variation remains largely unexplored. In this study, specific length amplified fragment sequencing(SLAF-Seq) was used to resequence a population comprising 197 F8recombinantinbred lines(RILs) derived from a cross between vegetable-type Qichi881 and oilseed-type YufengZC of B. juncea. In total, 438,895 high-quality SLAFs were discovered, 47,644 of which were polymorphic, and 3,887 of the polymorphic markers met the requirements for genetic map construction. The final map included 3,887 markers on 18 linkage groups and was 1,830.23 centiMorgan(cM) in length, with an average distance of 0.47 cM between adjacent markers. Using the newly constructed high-density genetic map, a total of 53 QTLs for erucicacid(EA), oleic acid(OA), and linolenic acid(LNA) were detected and integrated into eight consensus QTLswith two for each of these traits. For each of these three traits, two candidate genes were cloned and sequence analysis indicated colocalization with their respective consensus QTLs. The co-dominant allele-specific markers for Bju.FAD3.A03 and Bju.FAD3.B07 were developed and showed co-localization with their consensus QTLs andco-segregation with LNA content, further supporting the results of QTL mapping and bioinformatic analysis. Theexpression levels of the cloned homologous genes were also determined, and the genes were tightly correlatedwith the EA, OA and LNA contents of different lines. The results of this study will facilitate the improvement offatty acid traits and molecular breeding of B. juncea. Further uses of the high-density genetic map created in this study are also discussed.展开更多
Particle transport is a fundamental aspect of various systems,from artificial to biological.A common assumption is that particle motion follows Markovian(memoryless)processes in the absence of interaction between part...Particle transport is a fundamental aspect of various systems,from artificial to biological.A common assumption is that particle motion follows Markovian(memoryless)processes in the absence of interaction between particles.However,hydrodynamic memory and the interaction between particles are ubiquitous,leaving many fundamental questions unanswered regarding transport of interacting particles involving hydrodynamic drag in corrugated channels,as described by the fractional Langevin equation.This study examines the hydrodynamic transport of interacting non-Brownian particles moving within a corrugated channel.We propose a method that relies on factors such as temperature,the driving force to alternate between no transport and finite net transport.Of importance is to note that the absence of transport results from the clogging,while the transport consists of collective motion and independent motion.The transport systems investigated in this work suggest the potential for sensor functionality within the system.Our findings may prove valuable for exploring the transport with hydrodynamic memory in various fields,including biology,physics,and chemistry.展开更多
This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to externa...This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to external magnetic fields.A micromechanical model was created by simplifying the basic properties and composition of the interface,utilizing principles such as Eshelby’s equivalent inclusion theory and Hooke’s law,as well as applying uniform stress boundary conditions.Through the development of equations,the study predicted changes in effective mechanical properties,highlighting the significant influence of parameters like the interface phase,inclusions,and magnetic field on the effective elastic modulus and magnetostriction of the composite material.By shedding light on these relationships,the research offers valuable insights for the manufacture and application of ferromagnetic particle-reinforced superconducting matrix composites with interface phases,providing a foundation for future research in this area.展开更多
Stroke survivors often face significant challenges when performing daily self-care activities due to upper limb motor impairments.Traditional surface electromyography(sEMG)analysis typically focuses on isolated hand p...Stroke survivors often face significant challenges when performing daily self-care activities due to upper limb motor impairments.Traditional surface electromyography(sEMG)analysis typically focuses on isolated hand postures,overlooking the complexity of object-interactive behaviors that are crucial for promoting patient independence.This study introduces a novel framework that combines high-density sEMG(HD-sEMG)signals with an improved Whale Optimization Algorithm(IWOA)-optimized Long Short-Term Memory(LSTM)network to address this limitation.The key contributions of this work include:(1)the creation of a specialized HD-sEMG dataset that captures nine continuous self-care behaviors,along with time and posture markers,to better reflect real-world patient interactions;(2)the development of a multi-channel feature fusion module based on Pascal’s theorem,which enables efficient signal segmentation and spatial–temporal feature extraction;and(3)the enhancement of the IWOA algorithm,which integrates optimal point set initialization,a diversity-driven pooling mechanism,and cosine-based differential evolution to optimize LSTM hyperparameters,thereby improving convergence and global search capabilities.Experimental results demonstrate superior performance,achieving 99.58%accuracy in self-care behavior recognition and 86.19%accuracy for 17 continuous gestures on the Ninapro db2 benchmark.The framework operates with low latency,meeting the real-time requirements for assistive devices.By enabling precise,context-aware recognition of daily activities,this work advances personalized rehabilitation technologies,empowering stroke patients to regain autonomy in self-care tasks.The proposed methodology offers a robust,scalable solution for clinical applications,bridging the gap between laboratory-based gesture recognition and practical,patient-centered care.展开更多
The blocky LPSO particles were modulated by single-directional and multi-directional forging,and the effect of blocky LPSO particles on the anisotropy of mechanical properties of Mg-8.5Gd-2.5Y-1.5Zn-0.5Zr alloy forged...The blocky LPSO particles were modulated by single-directional and multi-directional forging,and the effect of blocky LPSO particles on the anisotropy of mechanical properties of Mg-8.5Gd-2.5Y-1.5Zn-0.5Zr alloy forged parts was investigated.In the present work,3D processing maps are established,and the forming domain that is both stable and power efficient is in the temperature range from 430 to 500℃ and strain rate range from 0.001 to 0.06 s^(-1),which is used to guide the single-directional forging(SDF)and multi-directional forging(MDF)experiments.The tensile mechanical properties reveal that the blocky LPSO particles have an influence on the mechanical anisotropy,especially in terms of the elongation anisotropy.The blocky LPSO particles after the MDF process have a more regular shape and smaller size and are homogeneously distributed,which is responsible for the low anisotropy of the elongation.In addition,the age-hardening capability of the MDF part is higher than that of the SDF part.展开更多
A partly clumped-particles combined with joint planes model was developed to simulate the microstructure of quartz mica schist.It considers grain-scale heterogeneity including microgeometry heterogeneity and grain-sca...A partly clumped-particles combined with joint planes model was developed to simulate the microstructure of quartz mica schist.It considers grain-scale heterogeneity including microgeometry heterogeneity and grain-scale elastic heterogeneity.Clumped-particles with larger volume and larger stiffness were used to represent stiff minerals such as quartz,the rest of unclumped particles with smaller stiffness were used to represent soft minerals such as mica.The joint planes,which have smaller stiffness and strength than mica,were used to describe schist.The extensive sensitivity studies have shown that the clump’s radius,clump’s content and joint plane’s strength affect the microscopic and macroscopic behaviors of sample.For DanBa quartz mica schist,the model calibrated uniaxial tests and well matched with the stress-strain curves,crack initiation stress and crack damage stress of laboratory test.展开更多
基金Project(2021YFC2801904)supported by the National Key R&D Program of ChinaProject(KY10100230067)supported by the Basic Product Innovation Research Project,China+3 种基金Projects(52271130,52305344)supported by the National Natural Science Foundation of ChinaProjects(ZR2020ME017,ZR2020QE186)supported by the Natural Science Foundation of Shandong Province,ChinaProjects(AMGM2024F11,AMGM2021F10,AMGM2023F06)supported by the Science Fund of Shandong Laboratory of Advanced Materials and Green Manufacturing at Yantai,ChinaProject(KY90200210015)supported by Leading Scientific Research Project of China National Nuclear Corporation(CNNC),China。
文摘WC particles reinforced CoCrFeNiMo high-entropy alloy(HEA)composite coatings were prepared on Cr12MoV steel successfully by laser cladding technology to improve the wear resistance of substrates.Effect of WC content on microstructure and wear property of the composite coatings was studied in detail.Large numbers of carbides with four main types:primary carbide crystals,eutectic structures,massive crystals growing along the periphery of the remaining WC particles and incompletely fused WC particles,were found to exist in the WC/CoCrFeNiMo composite coatings.With increasing WC content,the microhardness of coatings is gradually improved while the average friction coefficients follow the opposite trend due to solid solution strengthening and second phase strengthening effect.The maximum microhardness and minimum friction coefficient are HV_(0.2)689.7 and 0.72,respectively,for the composite coating with 30 wt.%WC,the wear resistance of the substrate is improved significantly,the wear mechanisms are spalling wear and abrasive wear due to their high microhardness.
基金supported by the National Key Research and Development Program of China(No.2019YFC1804202)the National Natural Science Foundation of China(Nos.22020102004 and 22125603)+1 种基金Tianjin Municipal Science and Technology Bureau(No.21JCZDJC00280)the Fundamental Research Funds for the Central Universities,and the Ministry of Education of China(No.T2017002).
文摘Polybrominated biphenyl ethers(PBDEs)and polycyclic aromatic hydrocarbons(PAHs)are commonly detected contaminants at e-waste recycling sites.Against the conventional wisdom that PBDEs and PAHs are highly immobile and persist primarily in shallowsurface soils,increasing evidence shows that these compounds can leach into the groundwater.Herein,we compare the leachabilities of PBDEs vs.PAHs from contaminated soils collected at an e-waste recycling site in Tianjin,China.Considerable amounts of BDE-209(0.3–2 ng/L)and phenanthrene(42–106 ng/L),the most abundant PBDE and PAH at the site,are detected in the effluents of columns packed with contaminated soils,with the specific concentrations varying with hydrodynamic and solution chemistry conditions.Interestingly,the leaching potential of BDE-209 appears to be closely related to the release of colloidal mineral particles,whereas the leachability of phenanthrene correlates well with the concentration of dissolved organic carbon in the effluent,but showing essentially no correlation with the concentration of mineral particles.The surprisingly different trends of the leachability observed between BDE-209 and phenanthrene is counterintuitive,as PBDEs and PAHs often co-exist at e-waste recycling sites(particularly at the sites wherein incineration is being practiced)and share many similarities in terms of physicochemical properties.One possible explanation is that due to its extremely low solubility,BDE-209 predominantly exists in free-phase(i.e.,as solid(nano)particles),whereas the more soluble phenanthrene is mainly sorbed to soil organic matter.Findings in this study underscore the need to better understand the mobility of highly hydrophobic organic contaminants at contaminated sites for improved risk management.
基金financially supported by the National Natural Science Foundation of China(No.51771125)the Sichuan Province Science and Technology Support Program(No.2020YFG0102)。
文摘Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.
基金supported by National Natural Science Foundation of China(No.22278352)National Key Research and Development Program of China(No.2021YFC3001100)+3 种基金Longyan City Science and Technology Plan Project(No.2020LYF17043)Longyan City Science and Technology Plan Project(No.2020LYF17042)ARC Discovery Project(No.DP200101238)and NHMRC Investigator Grant(No.APP2008698)supported by the Harvard Materials Research Science and Engineering Center(No.DMR2011754)。
文摘Biocompatible amphiphilic nanoparticles(NPs)with tunable particle morphology and surface property are important for their applications as functional materials.However,previously developed methods to prepare amphiphilic NPs generally involve several steps,especially an additional step for surface modification,greatly hindering their largescale production and widespread applications.Here,a versatile one-step strategy is developed to prepare biocompatible amphiphilic dimer NPs with tunable particle morphology and surface property.The amphiphilic dimer NPs,which consist of a hydrophobic shellac bulb and a hydrophilic poly(lactic acid)(PLA)bulb with PLA-poly(ethylene glycol)(PEG)on the bulb surface,are prepared in a single step by controlled co-precipitation and self-assembly.Amphiphilic PLA-PEG/shellac dimer NPs demonstrate excellent tunability in particle morphology,thus showing good performances in controlling the interfacial curvature and emulsion type.In addition,temperatureresponsive PLA-poly(N-isopropyl acrylamide)(PNIPAM)/shellac dimer NPs are prepared following the same method and emulsions stabilized by them show temperature-triggered response.The applications of PLA-PEG-folic acid(FA)/shellac dimer NPs for drug delivery have also been demonstrated,which show a very good performance.The strategy of preparing the dimer NPs is green,scalable,facile and versatile,which provides a good platform for the design of dimer NPs with tunable particle morphology and surface property for diverse applications.
文摘We review a 3d quantum gravity model, which incorporates massive spinning fields into the Euclidean path integral in a Chern-Simons formulation. Fundamental matter as defined in our previous preon model is recapped. Both quantum gravity and the particle model are shown to be derivable from the supersymmetric 3d Chern-Simons action. Forces-Matter unification is achieved.
基金financially supported by the National Natural Science Foundation of China(Grant 22278439,21776313)the Shandong Province Higher Education Youth Innovation Technology Support Program(Grant 2022KJ074)。
文摘Metal-support interactions and hydrogen spillover effects in heterogeneous catalysts play a crucial role in aromatic hydrogenation reactions;however,these effects are limited by the metal dispersion on the catalyst and the number of acceptable H*receptors.This study prepares highly dispersed Ni nanoparticles(NPs)catalysts on a Beta substrate via precursor structure topology transformation.In contrast to traditional support materials,the coordination and electronic structure changes between the Ni NPs and the support were achieved,further optimizing the active interface sites and enhancing hydrogen activation and hydrogenation performance.Additionally,the-OH groups at the strong acid sites in zeolite effectively intensified the hydrogen spillover effect as receptors for H^(*)migration and anchoring,accelerating the hydrogenation rate of aromatic rings.Under solvent-free conditions,this catalyst was used for the hydrogenation reaction of aromatic-rich oils,directly producing a C_(8)-C_(14)branched cycloalkanes mixture with an aromatic conversion rate of>99%.The cycloalkanes mixture produced by this method features high density(0.92 g/mL)and a low freezing point(<-60℃),making it suitable for use as high-density aviation fuel or as an additive to enhance the volumetric heat value of conventional aviation fuels in practical applications.
基金supported by the National Natural Science Foundation of China(Nos.52373045 and 52033005).
文摘In rotationally extruded fittings,high-density polyethylene(HDPE)pipes prepared using conventional processing methods often suffer from poor pressure resistance and low toughness.This study introduces an innovative rotary shear system(RSS)to address these deficiencies through controlled mandrel rotation and cooling rates.We successfully prepared self-reinforced HDPE pipes with a three-layer structure combining spherical and shish-kebab crystals.Rotational processing aligned the molecular chains in the ring direction and formed shish-kebab crystals.As a result,the annular tensile strength of the rotationally processed three-layer shish-kebab structure(TSK)pipe increased from 26.7 MPa to 76.3 MPa,an enhancement of 185.8%.Notably,while maintaining excellent tensile strength(73.4 MPa),the elongation at break of the spherulite shishkebab spherulite(SKS)tubes was improved to 50.1%,as compared to 33.8%in the case of shish-kebab spherulite shish-kebab(KSK)tubes.This improvement can be attributed to the changes in the micro-morphology and polymer structure within the SKS tubes,specifically due to the formation of small-sized shish-kebab crystals and the low degrees of interlocking.In addition,2D-SAXS analysis revealed that KSK tubes have higher tensile strength due to smaller crystal sizes and larger shish dimensions,forming dense interlocking structures.In contrast,the SKS and TSK tubes had thicker amorphous regions and smaller shish sizes,resulting in reduced interlocking and mechanical performance.
基金supported by the National Natural Science Foundation of China(Nos.U21A2027,42207113,and 42407141)。
文摘Studying the contribution of regional transport to ultrafine particles(UFPs)and the deposition effect of nanoscale particles in human respiratory system is conducive to exploring the impact of atmospheric particles on the environment and human health.Based on the data set of number concentration spectrum in the particle size range of 5.6–560 nm in the spring of Hefei,the Yangtze River Delta region obtained by a fast mobility particle sizer,the explosive growth characteristics,potential source identification and deposition flux analysis of UFPs were systematically studied.The results showed that the frequency of new particle formation(NPF)events during spring was 31.5%.SO_(2) and O_(3) contribute to NPF events.Daytime,higher temperature,stronger solar radiation and lower humidity were more conducive to the explosive growth of UFPs.In addition,regional transport of pollutants from the cities around Hefei played an important role in the accumulation mode particles,which were mainly affected by the land-source air mass from northwest Jiangsu(23.64%)and the sea-source air mass from the Yellow Sea(23.99%).It was worth noting that approximately 10,406 ng of UFPs enters the human respiratory system every day.Themain deposition area of 5.6–560 nm nanoscale particles was alveolar,5.6–400 nm is more likely to be deposited on alveolar,while nanoscale particles with particle size between 400 and 560 nm is more likely to be deposited on head airways.This study identified the deposition risk of nanoscale particles in the respiratory system under different particle sizes.
基金supported by the National Natural Science Foundation of China(No.31700475).
文摘Aerosol particle pollution has become an increasing serious environmental problem,and urban vegetation plays a long-lasting and positive role in mitigating it.This study compared the particle capture abilities of trees,shrubs,and herbs,and examined the compositions and influence of aerosol particles accumulated on leaf functional traits.Retained particles primarily contained Ca^(2+),K^(+),SO_(4)^(2-),NO_(3)^(-)and NH_(4)^(+),indicating their anthropogenic origins.The leathery-leaved tree Osmanthus fragrans and the papery-leaved herb Alternanthera sessilis demonstrated the higher competence in particle accumulation than other plants,and leaf morphologic structures(e.g.,leaf grooves,trichomes,waxy layers,and stomata characteristics)were closely associated with particle capture by plant species.Particle retention negatively impacted stomata,impeding photosynthesis,and reducing transpiration.In response to particle accumulation,plants tended to decrease specific leaf area and adjust stomatal conductance.Both growth form and leaf texture significantly influenced the particle capture abilities of different plant species.The substantial contribution of plants,particularly herbs in the lower vegetation strata,to particle removal should not be overlooked.Vegetation with a tree-shrub-herb configuration excels at particle capture,offering potential advantages in mitigating particle pollution and enhancing ecological benefits.
基金supported by the National Science Foundation of China under the Grant Nos.12127806 and 62175195the International Joint Research Laboratory for Micro/Nano Manufacturing and Measurement Technologies。
文摘High-density interconnect(HDI)soft electronics that can integrate multiple individual functions into one miniaturized monolithic system is promising for applications related to smart healthcare,soft robotics,and human-machine interactions.However,despite the recent advances,the development of three-dimensional(3D)soft electronics with both high resolution and high integration is still challenging because of the lack of efficient manufacturing methods to guarantee interlayer alignment of the high-density vias and reliable interlayer electrical conductivity.Here,an advanced 3D laser printing pathway,based on femtosecond laser direct writing(FLDW),is demonstrated for preparing liquid metal(LM)-based any layer HDI soft electronics.FLDW technology,with the characteristics of high spatial resolution and high precision,allows the maskless fabrication of high-resolution embedded LM microchannels and high-density vertical interconnect accesses for 3D integrated circuits.High-aspect-ratio blind/through LM microstructures are formed inside the elastomer due to the supermetalphobicity induced during laser ablation.The LM-based HDI circuit featuring high resolution(~1.5μm)and high integration(10-layer electrical interconnection)is achieved for customized soft electronics,including various customized multilayer passive electric components,soft multilayer circuit,and cross-scale multimode sensors.The 3D laser printing method provides a versatile approach for developing chip-level soft electronics.
基金supported by the National Key Research and Development Project(2023YFA1609100)the NSFC Funding(U2141207,52171111,52001083)+6 种基金Natural Science Foundation of Heilongjiang(YQ2023E026)China Postdoctoral Science foundation(2024M754149)Postdoctoral Fellowship Program of CPSF(GZC20242192)support from the National Science Foundation(DMR-1611180 and 1809640)with the program directors,DrsHKU Seed Fund for Collaborative Research(#2207101618)support by Croucher Senior Research Fellowship and City U Project(Project No.9229019)Shenzhen Science and Technology Program(Project No.JCYJ20220818101203007)。
文摘Dislocation strengthening,as one of the methods to simultaneously enhance the room temperature strength and ductility of alloys,does not achieve the desired strengthening and plasticity effect during elevated-temperature deformation.Here,we report a novel strategy to boost the dislocation multiplication and accumulation during deformation at elevated temperatures through dynamic strain aging(DSA).With the introduction of the rare-earth element Ho in Mg-Y-Zn alloy,Ho atoms diffuse toward dislocations during deformation at elevated temperatures,provoking the DSA effect,which increases the dislocation density significantly via the interactions of mobile dislocations and Ho atoms.The resulting alloy achieves a great enhancement of dislocation hardening and obtains the dual benefits of high strength and good ductility simultaneously at high homologous temperatures.The present work provides an effective strategy to enhancing the strength and ductility for elevated-temperature materials.
基金financially supported by the Program of the National Natural Science Foundation of China(Grant No.52371055)the Young Elite Scientist Sponsorship Program Cast(Grant No.YESS20200139)the Basic Scientific Research Project of Liaoning Provincial Department of Education(Grant No.JYTMS20230618)。
文摘The effect of intermetallic particles on the corrosion of 6061 aluminum alloy and its coating used in semiconductor processing systems was systematically studied via liquid and gas experiments and micromorphology characterization.The results revealed that a huge difference of corrosion resistance between imported and domestic 6061 aluminum alloys in HCl solution and gas acid mist experiments mainly was attributed to the different size and amount of Al_(15)(Fe,Mn)_(3)Si_(2).The corrosion resistance of domestic 6061 alloy in dry/wet semiconductor electronic special gas environments was worse than that of imported aluminum alloy,and there are great differences in the corrosion mechanism of 6061 alloy caused by the second phase in the two dry/wet environments.And the corrosion resistance of the hard anodized alumina film was closely related to the microscopic morphology of holes.The vertical and elongatedα-Al_(15)(Mn,Fe)_(3)Si_(2) phase was formed in the rolled aluminum alloy that has been rolled perpendicular to the surface of the substrate.Compared to the horizontal long hole,the longitudinal long holes generated by the verticalα-Al_(15)(Mn,Fe)_(3)Si_(2) phase will enable the corrosive medium to reach the substrate rapidly,which significantly weakens the corrosion resistance of the hard anodized film.
基金supported by National Natural Science Foundation of China(Nos.12275064 and 12475203)the Hebei Natural Science Fund(No.A2024201020)+1 种基金Hebei University Natural Science Research Innovation Team Project(No.IT2023B03)the Post-graduate’s Innovation Fund Project of Hebei University(No.HBU2024BS007)。
文摘The Feynman ratchet has the ability to convert random fluctuations into directional particle transport.The transport velocity of particles is highly dependent on their size,leading to directional transport and subsequent particle separation under suitable parameter conditions.Here,exploiting the distinct responses of particles with different sizes to the system,the separation of bi-dispersed dust particles is achieved experimentally in air at 35 Pa using a dusty plasma ratchet.To reveal the underlying mechanisms,we construct a plasma model and perform Langevin simulations for the particle separation.Our numerical results reveal that charged dust particles experience an asymmetric ratchet potential,which dictates their directional transport.Crucially,bi-dispersed dust particles are suspended at different heights and are subject to ratchet potentials with opposing asymmetries,resulting in their separation.These findings may offer new perspectives for related fields,including microfluidics,nanotechnology,and micrometer-scale particle manipulation.
基金financially supported by the Sichuan Provincial Science and Technology Fund for Distinguished Young Scholars,China(Grant No.2022JDJQ0028)Research Startup Fund by Sichuan University,China(Grant No.YJ202218).
文摘Triboelectric nanogenerators(TENGs)are emerging as new technologies to harvest electrical power from mechanical energy.With the distinctive working mechanism of triboelectric nanogenerators,they attract particular interest in healthcare monitoring,wearable electronics,and deformable energy harvesting,which raises the requirement for highly conformable devices with substantial energy outputs.Here,a simple,low-cost strategy for fabricating stretchable triboelectric nanogenerators with ultra-high electrical output is developed.The TENG is prepared using PTFE micron particles(PPTENG),contributing a different electrostatic induction process compared to TENG based on dielectric films,which was associated with the dynamics of particle motions in PP-TENG.The generator achieved an impressive voltage output of 1000 V with a current of 25 lA over a contact area of 40320 mm^(2).Additionally,the TENG exhibits excellent durability with a stretching strain of 500%,and the electrical output performance does not show any significant degradation even after 3000 cycles at a strain of 400%.The unique design of the device provides high conformability and can be used as a self-powered sensor for human motion detection.
基金funded by the Scientific and Technological Key Program of Guizhou Province, China (Qiankehezhicheng [2022] Key 031)the National Natural Science Foundation of China (32160483 and 32360497)+2 种基金the Post-Funded Project for the National Natural Science Foundation of China from Guizhou University ([2023]093)the Key Laboratory of Molecular Breeding for Grain and Oil Crops in Guizhou Province, China (Qiankehezhongyindi [2023]008)the Key Laboratory of Functional Agriculture of Guizhou Provincial Higher Education Institutions, China (Qianjiaoji [2023] 007)。
文摘Rapeseed mustard(Brassica juncea L.) is the third most important oilseed crop in the world, but the geneticmechanism underlying its massive phenotypic variation remains largely unexplored. In this study, specific length amplified fragment sequencing(SLAF-Seq) was used to resequence a population comprising 197 F8recombinantinbred lines(RILs) derived from a cross between vegetable-type Qichi881 and oilseed-type YufengZC of B. juncea. In total, 438,895 high-quality SLAFs were discovered, 47,644 of which were polymorphic, and 3,887 of the polymorphic markers met the requirements for genetic map construction. The final map included 3,887 markers on 18 linkage groups and was 1,830.23 centiMorgan(cM) in length, with an average distance of 0.47 cM between adjacent markers. Using the newly constructed high-density genetic map, a total of 53 QTLs for erucicacid(EA), oleic acid(OA), and linolenic acid(LNA) were detected and integrated into eight consensus QTLswith two for each of these traits. For each of these three traits, two candidate genes were cloned and sequence analysis indicated colocalization with their respective consensus QTLs. The co-dominant allele-specific markers for Bju.FAD3.A03 and Bju.FAD3.B07 were developed and showed co-localization with their consensus QTLs andco-segregation with LNA content, further supporting the results of QTL mapping and bioinformatic analysis. Theexpression levels of the cloned homologous genes were also determined, and the genes were tightly correlatedwith the EA, OA and LNA contents of different lines. The results of this study will facilitate the improvement offatty acid traits and molecular breeding of B. juncea. Further uses of the high-density genetic map created in this study are also discussed.
基金supported by the National Natural Science Foundation of China(Grant Nos.12365007 and 12265017)Yunnan Fundamental Research Projects(Grant Nos.202101AS070018 and 202101AV070015)+1 种基金the Scientific Research Foundation of the Yunnan Provincial Department of Education(Grant No.2023J1208)Xingdian Talents Support Program,and Yunnan Province Ten Thousand Talents Plan Young&Elite Talents Project,and Yunnan Province Computational Physics and Applied Science and Technology Innovation Team.The numerical simulation and significance estimation were performed on the Key Laboratory of High-Density Computing,Zhaotong University。
文摘Particle transport is a fundamental aspect of various systems,from artificial to biological.A common assumption is that particle motion follows Markovian(memoryless)processes in the absence of interaction between particles.However,hydrodynamic memory and the interaction between particles are ubiquitous,leaving many fundamental questions unanswered regarding transport of interacting particles involving hydrodynamic drag in corrugated channels,as described by the fractional Langevin equation.This study examines the hydrodynamic transport of interacting non-Brownian particles moving within a corrugated channel.We propose a method that relies on factors such as temperature,the driving force to alternate between no transport and finite net transport.Of importance is to note that the absence of transport results from the clogging,while the transport consists of collective motion and independent motion.The transport systems investigated in this work suggest the potential for sensor functionality within the system.Our findings may prove valuable for exploring the transport with hydrodynamic memory in various fields,including biology,physics,and chemistry.
基金supported by the National Natural Science Foundation of China(No.12262020).
文摘This study focused on investigating the effects of various factors on the mechanical properties of superconducting matrix composites reinforced with ferromagnetic particles and interface phases when exposed to external magnetic fields.A micromechanical model was created by simplifying the basic properties and composition of the interface,utilizing principles such as Eshelby’s equivalent inclusion theory and Hooke’s law,as well as applying uniform stress boundary conditions.Through the development of equations,the study predicted changes in effective mechanical properties,highlighting the significant influence of parameters like the interface phase,inclusions,and magnetic field on the effective elastic modulus and magnetostriction of the composite material.By shedding light on these relationships,the research offers valuable insights for the manufacture and application of ferromagnetic particle-reinforced superconducting matrix composites with interface phases,providing a foundation for future research in this area.
基金supported by the National Natural Science Foundation of China(72061006)the research on the auxiliary diagnosis system of chronic injury of levator scapulae based on the concept of digital twin(Contract No:Qian Kehe Support[2023]General 117)Research on indoor intelligent assisted walking robot for the rehabilitation of walking ability of the elderly(Contract No:Qian kehe Support[2023]General 124).
文摘Stroke survivors often face significant challenges when performing daily self-care activities due to upper limb motor impairments.Traditional surface electromyography(sEMG)analysis typically focuses on isolated hand postures,overlooking the complexity of object-interactive behaviors that are crucial for promoting patient independence.This study introduces a novel framework that combines high-density sEMG(HD-sEMG)signals with an improved Whale Optimization Algorithm(IWOA)-optimized Long Short-Term Memory(LSTM)network to address this limitation.The key contributions of this work include:(1)the creation of a specialized HD-sEMG dataset that captures nine continuous self-care behaviors,along with time and posture markers,to better reflect real-world patient interactions;(2)the development of a multi-channel feature fusion module based on Pascal’s theorem,which enables efficient signal segmentation and spatial–temporal feature extraction;and(3)the enhancement of the IWOA algorithm,which integrates optimal point set initialization,a diversity-driven pooling mechanism,and cosine-based differential evolution to optimize LSTM hyperparameters,thereby improving convergence and global search capabilities.Experimental results demonstrate superior performance,achieving 99.58%accuracy in self-care behavior recognition and 86.19%accuracy for 17 continuous gestures on the Ninapro db2 benchmark.The framework operates with low latency,meeting the real-time requirements for assistive devices.By enabling precise,context-aware recognition of daily activities,this work advances personalized rehabilitation technologies,empowering stroke patients to regain autonomy in self-care tasks.The proposed methodology offers a robust,scalable solution for clinical applications,bridging the gap between laboratory-based gesture recognition and practical,patient-centered care.
基金supports of the National Key Research and Development Program of China(Grant No.2021YFB3501005)the National Natural Science Foundation of China(Grant No.52071208)the Key R&D program of Shanxi Province(International Cooperation)(Grant No.201903D421036).
文摘The blocky LPSO particles were modulated by single-directional and multi-directional forging,and the effect of blocky LPSO particles on the anisotropy of mechanical properties of Mg-8.5Gd-2.5Y-1.5Zn-0.5Zr alloy forged parts was investigated.In the present work,3D processing maps are established,and the forming domain that is both stable and power efficient is in the temperature range from 430 to 500℃ and strain rate range from 0.001 to 0.06 s^(-1),which is used to guide the single-directional forging(SDF)and multi-directional forging(MDF)experiments.The tensile mechanical properties reveal that the blocky LPSO particles have an influence on the mechanical anisotropy,especially in terms of the elongation anisotropy.The blocky LPSO particles after the MDF process have a more regular shape and smaller size and are homogeneously distributed,which is responsible for the low anisotropy of the elongation.In addition,the age-hardening capability of the MDF part is higher than that of the SDF part.
基金supported by the Natural Science Foundation of Hubei Province(2021CFA081)the Fundamental Research Funds for the Central Universities(2042023kf0210)the National Natural Science Foundation of China(42277160).
文摘A partly clumped-particles combined with joint planes model was developed to simulate the microstructure of quartz mica schist.It considers grain-scale heterogeneity including microgeometry heterogeneity and grain-scale elastic heterogeneity.Clumped-particles with larger volume and larger stiffness were used to represent stiff minerals such as quartz,the rest of unclumped particles with smaller stiffness were used to represent soft minerals such as mica.The joint planes,which have smaller stiffness and strength than mica,were used to describe schist.The extensive sensitivity studies have shown that the clump’s radius,clump’s content and joint plane’s strength affect the microscopic and macroscopic behaviors of sample.For DanBa quartz mica schist,the model calibrated uniaxial tests and well matched with the stress-strain curves,crack initiation stress and crack damage stress of laboratory test.
