We report measurement of heating rates of 40 Ca＋ ions confined in our home-made microscopic surface-electrode trap by a Doppler recooling method. The ions are trapped with approximately 800 μm above the surface, and...We report measurement of heating rates of 40 Ca＋ ions confined in our home-made microscopic surface-electrode trap by a Doppler recooling method. The ions are trapped with approximately 800 μm above the surface, and are subjected to heating due to various noises in the trap. There are 3-5 ions involved to measure the heating rates precisely and efficiently. We show the heating rates in variance with the number and the position of the ions as well as the radio-frequency power, which are helpful for understanding the trap imperfection.展开更多
The effect of heating rates during vacuum debinding on the microstructure and mechanical properties of alumina ceramics are discussed in this paper.The threedimensional(3D)-printed alumina ceramics examined in this st...The effect of heating rates during vacuum debinding on the microstructure and mechanical properties of alumina ceramics are discussed in this paper.The threedimensional(3D)-printed alumina ceramics examined in this study were found to have a layered structure,and interlayer spacing increased as the heating rate increased The pore diameter,shrinkage,flexural strength and hardness were found to decrease as the heating rate increased due to weak interfacial bonding between alumina particles Shrinkage was found to be much larger along the Z direction than along the X or Y directions due to the layer-bylayer forming mode during 3D printing.0.5°C·min-1is considered the optimum heating rate,yielding ceramics with interlayer spacing of 0.65 lm,shrinkage of 2.6%2.3%and 4.0%along the X,Y and Z directions,respectively,flexural strength of 27.5 MPa,hardness of29.8 GPa,Vickers hardness of HV 266.5,pore diameter of356.8 nm,bulk density of 2.5 g·cm-3,and open porosity of38.4%.The debinding procedure used in this study could be used to produce a high-quality ceramic which can be used for fabricating alumina ceramic cores.展开更多
Oxide scale formation on a C-steel surface has been investigated using linear heating rates ranging from 0.1℃/min to 10℃/min at high temperatures. The studies on the oxide scale formation at high temperature (650℃)...Oxide scale formation on a C-steel surface has been investigated using linear heating rates ranging from 0.1℃/min to 10℃/min at high temperatures. The studies on the oxide scale formation at high temperature (650℃) at slower heating rate (0.1℃/min) shows that the kinetic regime is linear. X-ray diffraction measurements revealed that the scale constituents are significantly influenced by the heating rate. The adherence of the scale was improved by using slower heating rate (0.1℃/min-≤650℃), while above such degree the scale was susceptible to cracking and flaking out of the alloy surface. In fact, the development of oxide growth stresses can cause considerable scale cracking. As well, variation of the crystallite sizes under the aforementioned conditions might affect the scale stacking to the alloy surface. The secondary electron detector images of the oxide scale shows that the scale was imperfectly smooth and there were a number of voids and defects in the scale skin, especially at fast heating rate. This observation could be attributed to defects of the as-received alloy. In general, slower heating rate reduced the defects of the scale and improved its adherence.展开更多
The latitude-altitude distributions of radiative fluxes and heating rates are investigated by utilizing CloudSat satellite data over China during summer. The Tibetan Plateau causes the downward shortwave fluxes of the...The latitude-altitude distributions of radiative fluxes and heating rates are investigated by utilizing CloudSat satellite data over China during summer. The Tibetan Plateau causes the downward shortwave fluxes of the lower atmosphere over central China to be smaller than the fluxes over southern and northern China by generating more clouds. The existence of a larger quantity of clouds over central China reflects a greater amount of solar radiation back into space. The vertical gradients of upward shortwave radiative fluxes in the atmosphere below 8 km are greater than those above 8 km. The latitudinal-altitude distributions of downward longwave radiative fluxes show a slantwise decreasing trend from low latitudes to high latitudes that gradually weaken in the downward direction. The upward longwave radiative fluxes also weaken in the upward direction but with larger gradients. The maximum heating rates by solar radiation and cooling rates by longwave infrared radiation are located over 28 40°N at 7 8 km mean sea level (MSL), and they are larger than the rates in the northern and southern regions. The heating and cooling rates match well both vertically and geographically.展开更多
Gasification of biomass tar by pyrolysis is a valuable source for renewable energy,providing chemicals,a precursor to carbon material and potentially a raw material for liquid fuel.In this research,experimental studie...Gasification of biomass tar by pyrolysis is a valuable source for renewable energy,providing chemicals,a precursor to carbon material and potentially a raw material for liquid fuel.In this research,experimental studies via thermal gravimetric analysis(TGA)of biomass tar were implemented at three rapid heating rates(i.e.,10 K/min,50 K/min,100 K/min,respectively)in a nitrogen atmosphere.On the basis of analytical methods utilized in thermal dynamics and physical chemistry,the results showed that the thermogravimetric curve(TG)of the biomass moved in a high-temperature direction with an increase in the heating rate.The greater the heating rate,the steeper the curve and the lower the resolution,the lag phenomenon of the temperature being more significant.Concurrently,a differential thermal analysis(DTA)was one of the methods employed to study the relationship between the temperature difference and the temperature or time of the tested substance and a reference substance.The peak temperature and maximum reaction rate of the differential thermal analysis curve(DTA)increased as the heating rate,the volatiles and the molecular residence time of the biomass was shortened at a higher heating rate,thereby potentially inhibiting the generation of carbon and increasing the production and yield of liquid fuel.展开更多
Grain-oriented silicon steels were prepared at different heating rates during high temperature annealing,in which the evolution of magnetic properties,grain orientations and precipitates were studied.To illustrate the...Grain-oriented silicon steels were prepared at different heating rates during high temperature annealing,in which the evolution of magnetic properties,grain orientations and precipitates were studied.To illustrate the Zener factor,the diameter and number density of precipitates of interrupted testing samples were statistically calculated.The effect of precipitate ripening on the Goss texture and magnetic property was investigated.Data indicated that the trend of Zener factor was similar under different heating rates,first increasing and then decreasing,and that the precipitate maturing was greatly inhibited as the heating rate increased.Secondary recrystallization was developed at the temperature of 1010℃when a heating rate of 5℃/h was used,resulting in Goss,Brass and{110}<227>oriented grains growing abnormally and a magnetic induction intensity of 1.90T.Furthermore,increasing the heating rate to 20℃/h would inhibit the development of undesirable oriented grains and obtain a sharp Goss texture.However,when the heating rate was extremely fast,such as 40℃/h,poor secondary recrystallization was developed with many island grains,corresponding to a decrease in magnetic induction intensity to 1.87 T.At a suitable heating rate of 20℃/h,the sharpest Goss texture and the highest magnetic induction of 1.94 T with an onset secondary recrystallization temperature of 1020℃were found among the experimental variables in this study.The heating rate affected the initial temperature of secondary recrystallization by controlling the maturation of precipitates,leading to the deviation and dispersion of Goss texture,thereby reducing the magnetic properties.展开更多
This study aims to mitigate crosswind-induced performance degradation in Natural Draft Dry Cooling Towers used in power plants by developing and assessing windbreak configurations that enhance ventilation while minimi...This study aims to mitigate crosswind-induced performance degradation in Natural Draft Dry Cooling Towers used in power plants by developing and assessing windbreak configurations that enhance ventilation while minimizing additional airflow resistance.Three novel windbreak designs,namely single-windbreak configuration with curved profile,double-windbreak configuration with curved profile,and double-windbreak configuration with inverted curved profile,are proposed accordingly and evaluated against conventional solutions.Three-dimensional numerical models of a 120 m high NDDCT equipped with these windbreaks,together with a conventional Y-shaped windbreak,are developed for systematic comparison.The results demonstrate that windbreak effectiveness strongly depends on crosswind intensity.At low crosswind speeds of 0-6 m/s,the Y-shaped windbreak provides the greatest enhancement,increasing the ventilation rate by 25.45%and the heat rejection rate by 21.37%at 6 m/s compared with the no-windbreak configuration.In contrast,under moderate to strong crosswinds of 6-18 m/s,the single-windbreak configuration with curved profile exhibits superior performance.At 18 m/s,it increases the ventilation rate by 148.88%and the heat rejection rate by 79.74%relative to the baseline case,outperforming the Y-shaped windbreak by 26.59%in ventilation rate and 17.01%in heat rejection capacity.Analysis of airflow structure,temperature fields,and velocity distributions confirms that the single-windbreak configuration with curved profile more effectively suppresses crosswind penetration and promotes stable upward airflow at higher wind speeds.Based on a comprehensive assessment of aerodynamic and thermal performance,the Y-shaped windbreak is recommended for regions where crosswind speeds remain below 6 m/s,whereas the single-windbreak configuration with curved profile is preferable for sites exposed to stronger crosswinds exceeding this threshold.展开更多
The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao...The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao,North China,and Zhangzhou basins are of special interest due to their considerable exploration depths,extensive development history,and high levels of research activity.This study focuses on the three basins to analyze their thermal reservoir characteristics in eastern China.Between 2017 and 2023,the research team carried out a comprehensive analysis involving deep boreholes that exceeded 4000 m in depth within these three basins.They meticulously created detailed physical profiles that captured essential characteristics such as porosity,permeability,and thermal properties,reaching down to the basement of each basin.The findings indicated that variations in thermal conductivity within shallow geotechnical layers significantly influence the redistribution of deep thermal energy in the upper layers of the earth.Furthermore,differences in physical properties notably affect heat transport processes.The research proposes distinct heat models tailored for each basin:For the Songliao Basin,a low-permeability model with homogeneous thermal properties is constructed;for the North China Basin,high permeability and thermal conductivity layers are highlighted;and a fracture network controlling water and heat is presented in the Zhangzhou Basin.To elucidate the thermal structure of these basins,the Curie surface and Moho surface were analyzed.The shallow Curie surface indicates ongoing intense thermal activity stemming from crustal heat sources,while a shallow Moho surface signifies historical vigorous mantle thermal activity associated with mantle source heat production.Furthermore,the research evaluates the geothermal resources and the potential for carbon emission reduction in these basins.Total volume of exploitable geothermal fluid is estimated to be 76.9×10^(9) m^(3)/a,corresponding to an annual renewable geothermal energy 1.47×10^(16)k J.The implementation of geothermal energy could lead to a reduction in annual CO_(2)emissions by nearly 2×10^(9) t,which constitutes about 17.4%of China’s national carbon emissions in 2022.This estimation provides invaluable theoretical insights and data support for geothermal exploration and sustainable development in eastern China.展开更多
The effects of heating rate （ranging from 50 to 300 ℃/s） during the final annealing process on microstructure evolution and magnetic properties of cold rolled non-oriented electrical steel were investigated. It was...The effects of heating rate （ranging from 50 to 300 ℃/s） during the final annealing process on microstructure evolution and magnetic properties of cold rolled non-oriented electrical steel were investigated. It was found that increasing heating rate increased the nucleation temperature and complete recrystallization temperature. At the same time, heating rate increasing could cause the substantially refined structures for the recrystallization grains and this grain refinement would decline when the heating rate was beyond 50 ℃/s. The recrystallization texture exhibited pronounced improvement with heating rate, such as the intensity decrease of 〈111〉//ND （normal direction） fiber and the intensity increase of { 110}%〈001〉 Goss texture component. The texture improvement and grain size refinement caused by heating rate increasing resulted in complicated variation of the magnetic properties. The magnetic induction （B50） keeps increasing while heating rate increases from 15 to 300 ℃/s which is due to the recrystallized texture optimization caused by rapid heating. The core losses （P1.5/50） decrease while heating rate increases from 15 to 100 ℃/s; however, the core losses would increase when heating rate is higher than 100 ℃/s, which is caused by the mean grain size refinement after rapid heating annealing. The results indicate that recrystallization texture and the magnetic properties of the non-oriented electrical steel can be improved definitely by rapid heating during the final annealing treatment.展开更多
The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffract...The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffractometer and EBSD technology. The experimental results reveal that there is a non-monotonic relationship among solution heating rate, mechanical properties, microstructure and texture. As the solution heating rate increases, the strength variations are dependent on the tensile direction;work hardening exponent n decreases first, and then increases;plastic strain ratio r increases first, and then decreases, and finally increases. The final microstructure and texture are also affected by heating rate. As heating rate increases, the microstructure transforms from elongated grain structure to equiaxed grain structure, and the average grain size decreases first, and then increases, and decreases finally. Although the texture components including CubeND{001}<310> and P{011}<122> orientations almost have no change with the increase of heating rate, the texture intensity and volume fraction decrease first, and then increase, and finally decrease. Both microstructure and texture evolutions are weakly affected by heating rate. Improving heating rate is not always favorable for the development of fine equiaxed grain structure, weak texture and high average r value, which may be related to the recrystallization behavior.展开更多
The effects of heating rate on the alloy element partitioning and mechanical properties during the phase transformation ofα→βin Ti-6Al-4 V alloy under solution treatment have been investigated by the experiments an...The effects of heating rate on the alloy element partitioning and mechanical properties during the phase transformation ofα→βin Ti-6Al-4 V alloy under solution treatment have been investigated by the experiments and phase field simulations,which reveal the evolutions of microstructure and compositions at the non-equilibrium state and well verify the experimental results.The specific results indicate that the compositions measured through electron probe micro-analysis(EPMA)under a lower heating rate are close to the equilibrium ones corresponding to the solution temperature.Heating up to the target solution temperature,as the heating rate increases,the Al content decreases and V increases in the primaryα(α_(p))grain with a larger size,the volume fraction ofα_(p)increases and the composition gradient betweenα_(p)andβphases gets steeper.The interrelated relationship among the diffusion,compositions,solution temperature and free energy of the system has been discussed in detail.Moreover,increasing the heating rate(~20.0 K/min)may help to improve the mechanical properties of the alloy by mainly adjusting theα_(p)/β;volume fractions,α_(p)particle size and secondaryα(α_(p))size during the process of heating up to the solution temperature.These results may shed some light on the optimization of the knowledge-based heat treatment route.展开更多
The alloy was reheated to 580℃for tempering at rates of 2,5,10,20,and 40℃/s,respectively,after quenching.The amount,distribution,and stability of reversed austenite were investigated by X-ray diffraction(XRD)and ele...The alloy was reheated to 580℃for tempering at rates of 2,5,10,20,and 40℃/s,respectively,after quenching.The amount,distribution,and stability of reversed austenite were investigated by X-ray diffraction(XRD)and electron back scatter diffraction(EBSD).The microstructure and cryogenic impact energy were studied by scanning electron microscope(SEM),transmission electron microscope(TEM)and Charpy V-notch(CVN)tests.The results showed that when the sample was heated at 10℃/s,the volume fraction of reversed austenite exhibited maximum of 8%;the reversed austenite was uniform along all kinds of boundaries;the reversed austenite contained higher concentration of carbon which enabled it to be more stable.The cryogenic toughness of the alloy was greatly improved when heated at 10℃/s,as the fracture surface observation showed that it mainly fractured in ductile rupture mode,which was consistent with the results of cryogenic impact energy.展开更多
The mechanism for heat transfer of radiation is usually adopted to heat strip in vertical continuous annealing furnace. The rate of heat transfer among strip and other objects can be hugely affected by the parameters ...The mechanism for heat transfer of radiation is usually adopted to heat strip in vertical continuous annealing furnace. The rate of heat transfer among strip and other objects can be hugely affected by the parameters of strip speed, geometry factors and radiating characteristic of surfaces of strip, radiating tubes and walls of furnace. A model including all parameters is proposed for calculating the heat transfer coefficient, predicting the strip tempera- ture and boundary temperature of strip through analyzing these parameters. The boundary temperature is a important datum and different from average arithmetic value of temperature of strip and temperature in furnace. Also, the model can be used to analyze the relation for temperature of strip and heat transfer coefficient, total heat transfer quantity and heating time. The model is built by using the radiating heat transfer rate, the Newtonrs law of cooling, and lumped system analysis. The results of calculation are compared to the data from production line. The comparisons indicate that the model can well predict the heating process. The model is already applied for process control in pro- duction line. Also, this research will provide a new method for analyzing the radiation heat transfer.展开更多
The austenite formation kinetics in unalloyed cast ductile iron was studied on the basis of dilatometry measurements, and Avrami＇s equation was used to estimate the material＇s kinetic parameters. A continuous heatin...The austenite formation kinetics in unalloyed cast ductile iron was studied on the basis of dilatometry measurements, and Avrami＇s equation was used to estimate the material＇s kinetic parameters. A continuous heating transformation diagram was constructed us-ing heating rates in the range of 0.06 to 0.83℃·s^-1. As the heating rate was augmented, the critical temperatures, c1A and Aα, as well as the intercritical range, which was evaluated as the difference between the critical temperatures, α c1Δ T =A_a- A_c1 , increased. At a low heating rate, the kinetics of austenite formation was slow as a consequence of the iron＇s silicon content. The effect of heating rate on k and n, the kinetic parameters of Avrami＇s equation, was also determined. Parameter n, which is associated with nucleation sites and growth geometry, de-creased with an increase in heating rate. In addition, parameter k increased with the increase of heating rate, suggesting that the nucleation and growth rates are carbon-and silicon-diffusion controlled during austenite formation under continuous heating.展开更多
This study introduces a novel method of electric field sintering for preparing NdFeB magnets. NdFeB alloy compacts were all sintered by electric fields for 8 min at 1000~C with different preset heating rates. The char...This study introduces a novel method of electric field sintering for preparing NdFeB magnets. NdFeB alloy compacts were all sintered by electric fields for 8 min at 1000~C with different preset heating rates. The characteristics of electric field sintering and the effects of heating rate on the sintering densification of NdFeB alloys were also studied. It is found that electric field sintering is a new non-pressure rapid sintering method for preparing NdFeB magnets with fine grains at a relatively lower sintering temperature and in a shorter sintering time. Using this method, the sintering temperature and process of the compacts can be controlled accurately. When the preset heating rate in- creasing from 5 to 2000~C/s the densification of NdFeB sintered compacts gradHally improves. As the preset heating rate is 2000C/s, Nd-rich phases are small, dispersed and uniformly distributed in the sintered compact, and the magnet has a better microstructure than that made by conventional vacuum sintering. Also, the maximum energy product of the sintered magnet reaches 95% of conventionally vacuum sintered magnets.展开更多
Effects of temperature and heating rate on the mechanical properties of the tensile specimens of magnesium alloy AZ31 were experimentally investigated using a Gleeble-1500 thermo-mechanical material testing system.The...Effects of temperature and heating rate on the mechanical properties of the tensile specimens of magnesium alloy AZ31 were experimentally investigated using a Gleeble-1500 thermo-mechanical material testing system.The metallurgraphs of the fracture section of the specimens were also experimentally observed and analyzed for exploring their failure mechanism under different temperatures and heating rates.The results show that the higher the temperature,the lower the ultimate strength of the specimens.And the higher the heating rate,the higher the ultimate strength of the specimens.The high temperatures and high heating rates will induce microvoids in the specimens which make the specimens failure under relatively low loads.展开更多
To investigate the effect of alternating magnetic field on austenite transformation process in the case of rapid heating,the austenite kinetics model of AISI 1045 steel was built for spot continual induction hardening...To investigate the effect of alternating magnetic field on austenite transformation process in the case of rapid heating,the austenite kinetics model of AISI 1045 steel was built for spot continual induction hardening(SCIH)process.The results shows that the effect of alternating magnetic field on austenite transformation fraction reaches the maximum(about 3%)when heating rate is the lowest.Relatively low magnetic flux density still has a certain effect on the austenite transformation process during the SCIH process.Concave surface structure can reduce the influence scope of alternating magnetic field on surface in all cases and the minimum influence scope appears when the feed path of inductor is longitudinal.Convex surface structure can minimize the influence scope of alternating magnetic field in depth when the feed path of inductor is longitudinal.The austenite distribution of transitional region on surface for horizontal movement is more uniform than that for longitudinal movement.The austenite distribution of transitional region in depth for longitudinal movement is more uniform than that for horizontal movement.The simulated results are consistent with the experimental results and the austenite transformation kinetics model developed for SCIH process is valid.展开更多
The release characteristics of CH_(4),H_(2),CO and CO_(2) from iron coke hot briquette(ICHB)during carbonization were studied.The results show that compared with briquette without iron ore,Fe_(3)O_(4) can inhibit the ...The release characteristics of CH_(4),H_(2),CO and CO_(2) from iron coke hot briquette(ICHB)during carbonization were studied.The results show that compared with briquette without iron ore,Fe_(3)O_(4) can inhibit the release rate of H2 and promote the production of CO and CO_(2).In addition,when the heating rate increases from 3 to 7℃/min,the release rates of CH4 and H2 increase,while the release rates of CO and CO_(2) first increase and then decrease.The carbonization process of ICHB was segmented,and corresponding kinetic analysis was carried out.The results show that the activation energy of StageⅡand StageⅣis higher in the carbonization process of ICHB,and the active pyrolysis of coal and the reduction of iron ore occur in these two stages.In addition,the effect of heating rate on the kinetic parameters of ICHB carbonization process was investigated.It was found that when the heating rate increased,the reaction activation energy of StageⅣdecreased first and then increased,which was consistent with the release law of CO and CO_(2).The analysis showed that the increase in heating rate leads to more reactions at higher temperatures,resulting in an increase in the release rate of some gases.In addition,thermal hysteresis can also cause some processes to fail to fully react at the end of heating.It is also found that the apparent activation energy and preexponential factor have kinetic compensation effect during the car-bonization of ICHB.展开更多
The influence of heating rate on double reversible transformation in CuZnAlMnNi shape memory alloy was investigated by differential scanning calorimetry. It was found that rapid heating inhibits X -->M transformati...The influence of heating rate on double reversible transformation in CuZnAlMnNi shape memory alloy was investigated by differential scanning calorimetry. It was found that rapid heating inhibits X -->M transformation but is favorable to the reverse martensite transformation, giving rise to the approach of the two transformation peaks. With the decrease of heating rate, the two transformation peaks separate gradually.展开更多
We investigated the effects of heating rate on the process parameters of superplastic forming for Zr55Cu30Al10Ni5 by differential scanning calorimetry. The continuous heating and isothermal annealing analyses suggeste...We investigated the effects of heating rate on the process parameters of superplastic forming for Zr55Cu30Al10Ni5 by differential scanning calorimetry. The continuous heating and isothermal annealing analyses suggested that the temperatures of glass transition and onset crystallization are heating rate-dependent in the supercooled liquid region. Then, the time-temperature-transformation diagram under different heating rates indicates that increasing the heating rate can lead to an increase of the incubation time at the same anneal temperature in the supercooled liquid region. Based on the Arrhenius relationship, we discovered that the incubation time increases by 1.08-1.11 times with double increase of the heating rate at the same anneal temperature, and then verified it by the data of literatures and the experimental results. The obtained curve of the max available incubation time reveals that the incubation time at a certain anneal temperature in the supercooled liquid region is not infinite, and will increase with increasing heating rate until this temperature shifts out of the supercooled liquid region because of exceeding critical heating rate. It is concluded that heating rate must be an important processing parameter of superplastic forming for Zr55Cu30Al10Ni5.展开更多
基金Supported by the National Natural Science Foundation of China under Grant Nos Y5Z2111001,91421111 and 11674360
文摘We report measurement of heating rates of 40 Ca＋ ions confined in our home-made microscopic surface-electrode trap by a Doppler recooling method. The ions are trapped with approximately 800 μm above the surface, and are subjected to heating due to various noises in the trap. There are 3-5 ions involved to measure the heating rates precisely and efficiently. We show the heating rates in variance with the number and the position of the ions as well as the radio-frequency power, which are helpful for understanding the trap imperfection.
基金financially supported by the National Key Research and Development Program of China(No.2018YFB1106600)the National Natural Science Foundation of China(No.51672217)。
文摘The effect of heating rates during vacuum debinding on the microstructure and mechanical properties of alumina ceramics are discussed in this paper.The threedimensional(3D)-printed alumina ceramics examined in this study were found to have a layered structure,and interlayer spacing increased as the heating rate increased The pore diameter,shrinkage,flexural strength and hardness were found to decrease as the heating rate increased due to weak interfacial bonding between alumina particles Shrinkage was found to be much larger along the Z direction than along the X or Y directions due to the layer-bylayer forming mode during 3D printing.0.5°C·min-1is considered the optimum heating rate,yielding ceramics with interlayer spacing of 0.65 lm,shrinkage of 2.6%2.3%and 4.0%along the X,Y and Z directions,respectively,flexural strength of 27.5 MPa,hardness of29.8 GPa,Vickers hardness of HV 266.5,pore diameter of356.8 nm,bulk density of 2.5 g·cm-3,and open porosity of38.4%.The debinding procedure used in this study could be used to produce a high-quality ceramic which can be used for fabricating alumina ceramic cores.
文摘Oxide scale formation on a C-steel surface has been investigated using linear heating rates ranging from 0.1℃/min to 10℃/min at high temperatures. The studies on the oxide scale formation at high temperature (650℃) at slower heating rate (0.1℃/min) shows that the kinetic regime is linear. X-ray diffraction measurements revealed that the scale constituents are significantly influenced by the heating rate. The adherence of the scale was improved by using slower heating rate (0.1℃/min-≤650℃), while above such degree the scale was susceptible to cracking and flaking out of the alloy surface. In fact, the development of oxide growth stresses can cause considerable scale cracking. As well, variation of the crystallite sizes under the aforementioned conditions might affect the scale stacking to the alloy surface. The secondary electron detector images of the oxide scale shows that the scale was imperfectly smooth and there were a number of voids and defects in the scale skin, especially at fast heating rate. This observation could be attributed to defects of the as-received alloy. In general, slower heating rate reduced the defects of the scale and improved its adherence.
基金supported by the National Natural Science Foundation of China(Grant Nos.40875084and40705012)the National Key Technologies R&D Program of China(Grant No.2008BAC40B00)
文摘The latitude-altitude distributions of radiative fluxes and heating rates are investigated by utilizing CloudSat satellite data over China during summer. The Tibetan Plateau causes the downward shortwave fluxes of the lower atmosphere over central China to be smaller than the fluxes over southern and northern China by generating more clouds. The existence of a larger quantity of clouds over central China reflects a greater amount of solar radiation back into space. The vertical gradients of upward shortwave radiative fluxes in the atmosphere below 8 km are greater than those above 8 km. The latitudinal-altitude distributions of downward longwave radiative fluxes show a slantwise decreasing trend from low latitudes to high latitudes that gradually weaken in the downward direction. The upward longwave radiative fluxes also weaken in the upward direction but with larger gradients. The maximum heating rates by solar radiation and cooling rates by longwave infrared radiation are located over 28 40°N at 7 8 km mean sea level (MSL), and they are larger than the rates in the northern and southern regions. The heating and cooling rates match well both vertically and geographically.
基金the National Natural Science Foundation of China(551376056)"Study of regulation mechanisms and photo-thermal properties of photosynthetic hydrogen production under the condition of multiphase biomass flow",and The National High Technology Research and Development Program(863)of China(2012AA051502)-Research and demonstration of the key technology for biological hydrogen production".The authors would like to thank Prof.Qinglin Wu of Louisiana State University(USA)Dr.Li Jihong of North China Electric Power University for their assistance on this project.
文摘Gasification of biomass tar by pyrolysis is a valuable source for renewable energy,providing chemicals,a precursor to carbon material and potentially a raw material for liquid fuel.In this research,experimental studies via thermal gravimetric analysis(TGA)of biomass tar were implemented at three rapid heating rates(i.e.,10 K/min,50 K/min,100 K/min,respectively)in a nitrogen atmosphere.On the basis of analytical methods utilized in thermal dynamics and physical chemistry,the results showed that the thermogravimetric curve(TG)of the biomass moved in a high-temperature direction with an increase in the heating rate.The greater the heating rate,the steeper the curve and the lower the resolution,the lag phenomenon of the temperature being more significant.Concurrently,a differential thermal analysis(DTA)was one of the methods employed to study the relationship between the temperature difference and the temperature or time of the tested substance and a reference substance.The peak temperature and maximum reaction rate of the differential thermal analysis curve(DTA)increased as the heating rate,the volatiles and the molecular residence time of the biomass was shortened at a higher heating rate,thereby potentially inhibiting the generation of carbon and increasing the production and yield of liquid fuel.
文摘Grain-oriented silicon steels were prepared at different heating rates during high temperature annealing,in which the evolution of magnetic properties,grain orientations and precipitates were studied.To illustrate the Zener factor,the diameter and number density of precipitates of interrupted testing samples were statistically calculated.The effect of precipitate ripening on the Goss texture and magnetic property was investigated.Data indicated that the trend of Zener factor was similar under different heating rates,first increasing and then decreasing,and that the precipitate maturing was greatly inhibited as the heating rate increased.Secondary recrystallization was developed at the temperature of 1010℃when a heating rate of 5℃/h was used,resulting in Goss,Brass and{110}<227>oriented grains growing abnormally and a magnetic induction intensity of 1.90T.Furthermore,increasing the heating rate to 20℃/h would inhibit the development of undesirable oriented grains and obtain a sharp Goss texture.However,when the heating rate was extremely fast,such as 40℃/h,poor secondary recrystallization was developed with many island grains,corresponding to a decrease in magnetic induction intensity to 1.87 T.At a suitable heating rate of 20℃/h,the sharpest Goss texture and the highest magnetic induction of 1.94 T with an onset secondary recrystallization temperature of 1020℃were found among the experimental variables in this study.The heating rate affected the initial temperature of secondary recrystallization by controlling the maturation of precipitates,leading to the deviation and dispersion of Goss texture,thereby reducing the magnetic properties.
基金supported by the National Natural Science Foundation of China(Grant No.52476206)the Key R&D Program of Shandong Province,China(Grant No.2025CXGC010203)+1 种基金the Guangdong Basic and Applied Basic Research Foundation(Grant No.2025A1515012123)the Shandong Natural Science Foundation(Grant No.ZR2022ME008).
文摘This study aims to mitigate crosswind-induced performance degradation in Natural Draft Dry Cooling Towers used in power plants by developing and assessing windbreak configurations that enhance ventilation while minimizing additional airflow resistance.Three novel windbreak designs,namely single-windbreak configuration with curved profile,double-windbreak configuration with curved profile,and double-windbreak configuration with inverted curved profile,are proposed accordingly and evaluated against conventional solutions.Three-dimensional numerical models of a 120 m high NDDCT equipped with these windbreaks,together with a conventional Y-shaped windbreak,are developed for systematic comparison.The results demonstrate that windbreak effectiveness strongly depends on crosswind intensity.At low crosswind speeds of 0-6 m/s,the Y-shaped windbreak provides the greatest enhancement,increasing the ventilation rate by 25.45%and the heat rejection rate by 21.37%at 6 m/s compared with the no-windbreak configuration.In contrast,under moderate to strong crosswinds of 6-18 m/s,the single-windbreak configuration with curved profile exhibits superior performance.At 18 m/s,it increases the ventilation rate by 148.88%and the heat rejection rate by 79.74%relative to the baseline case,outperforming the Y-shaped windbreak by 26.59%in ventilation rate and 17.01%in heat rejection capacity.Analysis of airflow structure,temperature fields,and velocity distributions confirms that the single-windbreak configuration with curved profile more effectively suppresses crosswind penetration and promotes stable upward airflow at higher wind speeds.Based on a comprehensive assessment of aerodynamic and thermal performance,the Y-shaped windbreak is recommended for regions where crosswind speeds remain below 6 m/s,whereas the single-windbreak configuration with curved profile is preferable for sites exposed to stronger crosswinds exceeding this threshold.
基金funded by the Basic Scientific Research of China Geological Academy(YK202305)National Key R&D Program of China(2019YFB1504101)+1 种基金National Natural Science Foundation of China(41602271)China Geological Survey(DD20160207 and DD20189112)。
文摘The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao,North China,and Zhangzhou basins are of special interest due to their considerable exploration depths,extensive development history,and high levels of research activity.This study focuses on the three basins to analyze their thermal reservoir characteristics in eastern China.Between 2017 and 2023,the research team carried out a comprehensive analysis involving deep boreholes that exceeded 4000 m in depth within these three basins.They meticulously created detailed physical profiles that captured essential characteristics such as porosity,permeability,and thermal properties,reaching down to the basement of each basin.The findings indicated that variations in thermal conductivity within shallow geotechnical layers significantly influence the redistribution of deep thermal energy in the upper layers of the earth.Furthermore,differences in physical properties notably affect heat transport processes.The research proposes distinct heat models tailored for each basin:For the Songliao Basin,a low-permeability model with homogeneous thermal properties is constructed;for the North China Basin,high permeability and thermal conductivity layers are highlighted;and a fracture network controlling water and heat is presented in the Zhangzhou Basin.To elucidate the thermal structure of these basins,the Curie surface and Moho surface were analyzed.The shallow Curie surface indicates ongoing intense thermal activity stemming from crustal heat sources,while a shallow Moho surface signifies historical vigorous mantle thermal activity associated with mantle source heat production.Furthermore,the research evaluates the geothermal resources and the potential for carbon emission reduction in these basins.Total volume of exploitable geothermal fluid is estimated to be 76.9×10^(9) m^(3)/a,corresponding to an annual renewable geothermal energy 1.47×10^(16)k J.The implementation of geothermal energy could lead to a reduction in annual CO_(2)emissions by nearly 2×10^(9) t,which constitutes about 17.4%of China’s national carbon emissions in 2022.This estimation provides invaluable theoretical insights and data support for geothermal exploration and sustainable development in eastern China.
基金Item Sponsored by National Natural Science Foundation of China (50874010 ,50802008) Program for New Century Excellent Talents in University of China (NCET-05-0101)
文摘The effects of heating rate （ranging from 50 to 300 ℃/s） during the final annealing process on microstructure evolution and magnetic properties of cold rolled non-oriented electrical steel were investigated. It was found that increasing heating rate increased the nucleation temperature and complete recrystallization temperature. At the same time, heating rate increasing could cause the substantially refined structures for the recrystallization grains and this grain refinement would decline when the heating rate was beyond 50 ℃/s. The recrystallization texture exhibited pronounced improvement with heating rate, such as the intensity decrease of 〈111〉//ND （normal direction） fiber and the intensity increase of { 110}%〈001〉 Goss texture component. The texture improvement and grain size refinement caused by heating rate increasing resulted in complicated variation of the magnetic properties. The magnetic induction （B50） keeps increasing while heating rate increases from 15 to 300 ℃/s which is due to the recrystallized texture optimization caused by rapid heating. The core losses （P1.5/50） decrease while heating rate increases from 15 to 100 ℃/s; however, the core losses would increase when heating rate is higher than 100 ℃/s, which is caused by the mean grain size refinement after rapid heating annealing. The results indicate that recrystallization texture and the magnetic properties of the non-oriented electrical steel can be improved definitely by rapid heating during the final annealing treatment.
基金The authors are grateful for the financial supports from the Science Challenge Project(TZ2018001)the State Key Laboratory of Advanced Metals and Materials University of Science and Technology Beijing,China(2019-Z02)+3 种基金the National Natural Science Foundation of China(52075272)the Key Laboratory of Impact and Safety Engineering,Ministry of Education,Ningbo University,China(CJ201912)the Ningbo Natural Science Foundation,China(2018A610174)the K.C.Wong Magna Fund from Ningbo University,China.
文摘The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffractometer and EBSD technology. The experimental results reveal that there is a non-monotonic relationship among solution heating rate, mechanical properties, microstructure and texture. As the solution heating rate increases, the strength variations are dependent on the tensile direction;work hardening exponent n decreases first, and then increases;plastic strain ratio r increases first, and then decreases, and finally increases. The final microstructure and texture are also affected by heating rate. As heating rate increases, the microstructure transforms from elongated grain structure to equiaxed grain structure, and the average grain size decreases first, and then increases, and decreases finally. Although the texture components including CubeND{001}<310> and P{011}<122> orientations almost have no change with the increase of heating rate, the texture intensity and volume fraction decrease first, and then increase, and finally decrease. Both microstructure and texture evolutions are weakly affected by heating rate. Improving heating rate is not always favorable for the development of fine equiaxed grain structure, weak texture and high average r value, which may be related to the recrystallization behavior.
基金support from the National Natural Science Foundation of China(No.51701219)the Doctoral Scientific Research Foundation of Liaoning Province(No.20180540133)the Special Project on Information Technology of the Chinese Academy of Sciences(No.XXH13506–304)。
文摘The effects of heating rate on the alloy element partitioning and mechanical properties during the phase transformation ofα→βin Ti-6Al-4 V alloy under solution treatment have been investigated by the experiments and phase field simulations,which reveal the evolutions of microstructure and compositions at the non-equilibrium state and well verify the experimental results.The specific results indicate that the compositions measured through electron probe micro-analysis(EPMA)under a lower heating rate are close to the equilibrium ones corresponding to the solution temperature.Heating up to the target solution temperature,as the heating rate increases,the Al content decreases and V increases in the primaryα(α_(p))grain with a larger size,the volume fraction ofα_(p)increases and the composition gradient betweenα_(p)andβphases gets steeper.The interrelated relationship among the diffusion,compositions,solution temperature and free energy of the system has been discussed in detail.Moreover,increasing the heating rate(~20.0 K/min)may help to improve the mechanical properties of the alloy by mainly adjusting theα_(p)/β;volume fractions,α_(p)particle size and secondaryα(α_(p))size during the process of heating up to the solution temperature.These results may shed some light on the optimization of the knowledge-based heat treatment route.
文摘The alloy was reheated to 580℃for tempering at rates of 2,5,10,20,and 40℃/s,respectively,after quenching.The amount,distribution,and stability of reversed austenite were investigated by X-ray diffraction(XRD)and electron back scatter diffraction(EBSD).The microstructure and cryogenic impact energy were studied by scanning electron microscope(SEM),transmission electron microscope(TEM)and Charpy V-notch(CVN)tests.The results showed that when the sample was heated at 10℃/s,the volume fraction of reversed austenite exhibited maximum of 8%;the reversed austenite was uniform along all kinds of boundaries;the reversed austenite contained higher concentration of carbon which enabled it to be more stable.The cryogenic toughness of the alloy was greatly improved when heated at 10℃/s,as the fracture surface observation showed that it mainly fractured in ductile rupture mode,which was consistent with the results of cryogenic impact energy.
基金Item Sponsored by National Science and Technology Support Program for 12th Five-Year Plan of China(2011BAE13B02)
文摘The mechanism for heat transfer of radiation is usually adopted to heat strip in vertical continuous annealing furnace. The rate of heat transfer among strip and other objects can be hugely affected by the parameters of strip speed, geometry factors and radiating characteristic of surfaces of strip, radiating tubes and walls of furnace. A model including all parameters is proposed for calculating the heat transfer coefficient, predicting the strip tempera- ture and boundary temperature of strip through analyzing these parameters. The boundary temperature is a important datum and different from average arithmetic value of temperature of strip and temperature in furnace. Also, the model can be used to analyze the relation for temperature of strip and heat transfer coefficient, total heat transfer quantity and heating time. The model is built by using the radiating heat transfer rate, the Newtonrs law of cooling, and lumped system analysis. The results of calculation are compared to the data from production line. The comparisons indicate that the model can well predict the heating process. The model is already applied for process control in pro- duction line. Also, this research will provide a new method for analyzing the radiation heat transfer.
基金the National Council of Science and Technology of Mexico(CONACYT) for the scholarship(No.173101) received for his doctoral studiesthe CONACYT for the support received through grant CB-178511
文摘The austenite formation kinetics in unalloyed cast ductile iron was studied on the basis of dilatometry measurements, and Avrami＇s equation was used to estimate the material＇s kinetic parameters. A continuous heating transformation diagram was constructed us-ing heating rates in the range of 0.06 to 0.83℃·s^-1. As the heating rate was augmented, the critical temperatures, c1A and Aα, as well as the intercritical range, which was evaluated as the difference between the critical temperatures, α c1Δ T =A_a- A_c1 , increased. At a low heating rate, the kinetics of austenite formation was slow as a consequence of the iron＇s silicon content. The effect of heating rate on k and n, the kinetic parameters of Avrami＇s equation, was also determined. Parameter n, which is associated with nucleation sites and growth geometry, de-creased with an increase in heating rate. In addition, parameter k increased with the increase of heating rate, suggesting that the nucleation and growth rates are carbon-and silicon-diffusion controlled during austenite formation under continuous heating.
基金the National Natural Science Foundation of China(No.50945018)
文摘This study introduces a novel method of electric field sintering for preparing NdFeB magnets. NdFeB alloy compacts were all sintered by electric fields for 8 min at 1000~C with different preset heating rates. The characteristics of electric field sintering and the effects of heating rate on the sintering densification of NdFeB alloys were also studied. It is found that electric field sintering is a new non-pressure rapid sintering method for preparing NdFeB magnets with fine grains at a relatively lower sintering temperature and in a shorter sintering time. Using this method, the sintering temperature and process of the compacts can be controlled accurately. When the preset heating rate in- creasing from 5 to 2000~C/s the densification of NdFeB sintered compacts gradHally improves. As the preset heating rate is 2000C/s, Nd-rich phases are small, dispersed and uniformly distributed in the sintered compact, and the magnet has a better microstructure than that made by conventional vacuum sintering. Also, the maximum energy product of the sintered magnet reaches 95% of conventionally vacuum sintered magnets.
基金Projects(10872221,50621403)supported by the National Natural Science Foundation of China
文摘Effects of temperature and heating rate on the mechanical properties of the tensile specimens of magnesium alloy AZ31 were experimentally investigated using a Gleeble-1500 thermo-mechanical material testing system.The metallurgraphs of the fracture section of the specimens were also experimentally observed and analyzed for exploring their failure mechanism under different temperatures and heating rates.The results show that the higher the temperature,the lower the ultimate strength of the specimens.And the higher the heating rate,the higher the ultimate strength of the specimens.The high temperatures and high heating rates will induce microvoids in the specimens which make the specimens failure under relatively low loads.
基金Projects(51905390,51575415)supported by the National Natural Science Foundation of China。
文摘To investigate the effect of alternating magnetic field on austenite transformation process in the case of rapid heating,the austenite kinetics model of AISI 1045 steel was built for spot continual induction hardening(SCIH)process.The results shows that the effect of alternating magnetic field on austenite transformation fraction reaches the maximum(about 3%)when heating rate is the lowest.Relatively low magnetic flux density still has a certain effect on the austenite transformation process during the SCIH process.Concave surface structure can reduce the influence scope of alternating magnetic field on surface in all cases and the minimum influence scope appears when the feed path of inductor is longitudinal.Convex surface structure can minimize the influence scope of alternating magnetic field in depth when the feed path of inductor is longitudinal.The austenite distribution of transitional region on surface for horizontal movement is more uniform than that for longitudinal movement.The austenite distribution of transitional region in depth for longitudinal movement is more uniform than that for horizontal movement.The simulated results are consistent with the experimental results and the austenite transformation kinetics model developed for SCIH process is valid.
文摘The release characteristics of CH_(4),H_(2),CO and CO_(2) from iron coke hot briquette(ICHB)during carbonization were studied.The results show that compared with briquette without iron ore,Fe_(3)O_(4) can inhibit the release rate of H2 and promote the production of CO and CO_(2).In addition,when the heating rate increases from 3 to 7℃/min,the release rates of CH4 and H2 increase,while the release rates of CO and CO_(2) first increase and then decrease.The carbonization process of ICHB was segmented,and corresponding kinetic analysis was carried out.The results show that the activation energy of StageⅡand StageⅣis higher in the carbonization process of ICHB,and the active pyrolysis of coal and the reduction of iron ore occur in these two stages.In addition,the effect of heating rate on the kinetic parameters of ICHB carbonization process was investigated.It was found that when the heating rate increased,the reaction activation energy of StageⅣdecreased first and then increased,which was consistent with the release law of CO and CO_(2).The analysis showed that the increase in heating rate leads to more reactions at higher temperatures,resulting in an increase in the release rate of some gases.In addition,thermal hysteresis can also cause some processes to fail to fully react at the end of heating.It is also found that the apparent activation energy and preexponential factor have kinetic compensation effect during the car-bonization of ICHB.
文摘The influence of heating rate on double reversible transformation in CuZnAlMnNi shape memory alloy was investigated by differential scanning calorimetry. It was found that rapid heating inhibits X -->M transformation but is favorable to the reverse martensite transformation, giving rise to the approach of the two transformation peaks. With the decrease of heating rate, the two transformation peaks separate gradually.
基金Funded by the National Natural Science Foundation of China(Nos.51175210 and 51175211)
文摘We investigated the effects of heating rate on the process parameters of superplastic forming for Zr55Cu30Al10Ni5 by differential scanning calorimetry. The continuous heating and isothermal annealing analyses suggested that the temperatures of glass transition and onset crystallization are heating rate-dependent in the supercooled liquid region. Then, the time-temperature-transformation diagram under different heating rates indicates that increasing the heating rate can lead to an increase of the incubation time at the same anneal temperature in the supercooled liquid region. Based on the Arrhenius relationship, we discovered that the incubation time increases by 1.08-1.11 times with double increase of the heating rate at the same anneal temperature, and then verified it by the data of literatures and the experimental results. The obtained curve of the max available incubation time reveals that the incubation time at a certain anneal temperature in the supercooled liquid region is not infinite, and will increase with increasing heating rate until this temperature shifts out of the supercooled liquid region because of exceeding critical heating rate. It is concluded that heating rate must be an important processing parameter of superplastic forming for Zr55Cu30Al10Ni5.
