In this research, the dynamic recrystallization （DRX） behavior of an as-cast precipitation hardenable （PH） stainless steel was investigated by conducting hot compression tests at temperatures between 950-1150℃ an...In this research, the dynamic recrystallization （DRX） behavior of an as-cast precipitation hardenable （PH） stainless steel was investigated by conducting hot compression tests at temperatures between 950-1150℃ and under strain rates of 0.001-1 s^-1. The flow stress curves show that the DRX is responsible for flow softening during hot compression. The effects of temperature and strain rate on the strain and stress corresponding to peak point （εp and σp） of flow curve were analyzed individually. It is realized that, they increase with strain rate and decrease with temperature. The relationship between Zener-Hollomon parameter （Z） and εp was investigated and the equation of εp=4.3×10^-4^0.14 was proposed. The strain for the maximum rate of DRX （εmax） was determined under different deformation conditions. Therefore, it is realized that it increases with Z parameter and vise versa. On the basis of obtained results, the equation of εmax=9.5 × 10^-4Z0.12 was proposed.展开更多
This study focuses on a new and high-efficiency approach in a unified sense of accurately simulating strength-degrading effects for geomaterials,including non-symmetric hardening-to-softening effects in tension and co...This study focuses on a new and high-efficiency approach in a unified sense of accurately simulating strength-degrading effects for geomaterials,including non-symmetric hardening-to-softening effects in tension and compression as well as non-symmetric tensile and compressive stiffness-degrading effects during unloading.It is intended to bypass both modeling and numerical complexities involved in existing approaches.To this goal,new elastoplastic equations are established with new numerical techniques.With a decoupling technique of treating tension-compression asymmetry,the foregoing complex effects are automatically incorporated as inherent response features of the new elastoplastic equations,thus bypassing usual modeling complexities.A new numerical technique of renormalizing piecewise spline functions is introduced to resolve the central yet tough issue of obtaining accurate and unified expressions for the tensile and compressive strength functions,thus bypassing usual numerical complexities and uncertainties in treating numerous unknown parameters and multiple ad hoc criteria.As such,the new approach is not only of wide applicability for various geomaterials but also of high computational efficiency with no more than three adjustable parameters.Toward validating the efficacy of the new approach,numerical examples for granite,salt rock,and sandstone-concrete combined body as well as plain concrete,high-performance concrete,and ultrahigh-performance concrete are presented by comparing model predictions with multiple data sets for strength-degrading effects in tension and compression.展开更多
Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed...Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed.For all of water,oil,air and furnace cooling,there is almost-complete martensite with the favorable hardenability.The increase in cooling rate mainly increases the density of dislocation and residual strain in the as-solution annealed matrix.After aging treatment,the cooling rate dominates the ratio of high-angle grain boundaries(HAGBs)instead of the size of martensite blocks.The ratio of HAGBs continuously increases with the decreased cooling rate,while the width of blocks maintains 2.40-2.49μm.Meanwhile,more reversed austenite distributes at the martensite sub-grain boundaries.By comparison,the increased rate of water cooling contributes to a favorable precipitation of NiAl with fine size and dispersive distribution caused by more accumulated internal defects of vacancies and dislocations.With the decrease of cooling rate,NiAl precipitates exhibits a similar diameter of~7 nm while a larger inter-particle distance of~22 nm.In the case of low cooling rate(oil,air and furnace),the stable precipitation strengthening effect contributes to a high yield strength of~1.3 GPa and ultimate tensile strength of~1.4 GPa.The high-ratio HAGBs,reversed austenite and NiAl precipitates with larger-interparticle distance synergistically improve the impact toughness(V-notched Charpy impact energy of 100-110 J).展开更多
This study focuses on a 60 V trench MOSFET device designed for operation in space radiation environments.By increasing the bulk region concentration and placing the etched gate trench after the P+implantation process,...This study focuses on a 60 V trench MOSFET device designed for operation in space radiation environments.By increasing the bulk region concentration and placing the etched gate trench after the P+implantation process,we successfully reduced the threshold voltage shift from 6.5 to 2.2 V under a total dose of 400 krad(Si)^(60)Co,allowing the device to operate normally.Structurally,by embedding the source metal in the active and terminal regions,the device demonstrated current degradation without experiencing single-event burnout when subjected to a drain voltage of 60 V and a linear energy transfer value of 75.4 MeV·cm^(2)∕mg from tantalum-ion incidence.TCAD simulations verified that the embedded source metal effectively suppressed parasitic transistor conduction and eliminated the base-region expansion effect,thereby lowering the maximum temperature from 8000 to 1400 K.The irradiation effects of the embedded source metal in the terminal region were also investigated,which can improve the reverse recovery and ensure that the terminal metal does not melt prematurely,thereby significantly enhancing the radiation hardness of the device.展开更多
Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding str...Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding strength in titanium/stainless steel laminated composites were investigated.Results indicate that the hardened layer reduces the interfacial bonding strength from over 261 MPa to less than 204 MPa.During the cold roll-bonding process,the hardened layer fractures,leading to the formation of multi-scale cracks that are difficult for the stainless steel to fill.This not only hinders the development of an interlocking interface but also leads to the presence of numerous microcracks and hardened blocks along the nearly straight interface,consequently weakening the interfacial bonding strength.In metals with high work hardening rates,the conventional approach of enhancing interface interlocking and improving interfacial bonding strength by using a surface-hardened layer becomes less effective.展开更多
This study presents a machine learning-based method for predicting fragment velocity distribution in warhead fragmentation under explosive loading condition.The fragment resultant velocities are correlated with key de...This study presents a machine learning-based method for predicting fragment velocity distribution in warhead fragmentation under explosive loading condition.The fragment resultant velocities are correlated with key design parameters including casing dimensions and detonation positions.The paper details the finite element analysis for fragmentation,the characterizations of the dynamic hardening and fracture models,the generation of comprehensive datasets,and the training of the ANN model.The results show the influence of casing dimensions on fragment velocity distributions,with the tendencies indicating increased resultant velocity with reduced thickness,increased length and diameter.The model's predictive capability is demonstrated through the accurate predictions for both training and testing datasets,showing its potential for the real-time prediction of fragmentation performance.展开更多
Triggered seismicity is a key hazard where fluids are injected or withdrawn from the subsurface and may impact permeability. Understanding the mechanisms that control fluid injection-triggered seismicity allows its mi...Triggered seismicity is a key hazard where fluids are injected or withdrawn from the subsurface and may impact permeability. Understanding the mechanisms that control fluid injection-triggered seismicity allows its mitigation. Key controls on seismicity are defined in terms of fault and fracture strength, second-order frictional response and stability, and competing fluid-driven mechanisms for arrest. We desire to constrain maximum event magnitudes in triggered earthquakes by relating pre-existing critical stresses to fluid injection volume to explain why some recorded events are significantly larger than anticipated seismic moment thresholds. This formalism is consistent with several uncharacteristically large fluid injection-triggered earthquakes. Such methods of reactivating fractures and faults by hydraulic stimulation in shear or tensile fracturing are routinely used to create permeability in the subsurface. Microearthquakes (MEQs) generated by such stimulations can be used to diagnose permeability evolution. Although high-fidelity data sets are scarce, the EGS-Collab and Utah FORGE hydraulic stimulation field demonstration projects provide high-fidelity data sets that concurrently track permeability evolution and triggered seismicity. Machine learning deciphers the principal features of MEQs and the resulting permeability evolution that best track permeability changes – with transfer learning methods allowing robust predictions across multiple eological settings. Changes in permeability at reactivated fractures in both shear and extensional modes suggest that permeability change (Δk) scales with the seismic moment (M) of individual MEQs as Δk∝M. This scaling relation is exact at early times but degrades with successive MEQs, but provides a method for characterizing crustal permeability evolution using MEQs, alone. Importantly, we quantify for the first time the role of prestress in defining the elevated magnitude and seismic moment of fluid injection-triggered events, and demonstrate that such MEQs can also be used as diagnostic in quantifying permeability evolution in the crust.展开更多
The pursuit of Ag-based alloys with both high strength and toughness has posed a longstanding chal-lenge.In this study,we investigated the cluster strengthening and grain refinement toughening mecha-nisms in fully oxi...The pursuit of Ag-based alloys with both high strength and toughness has posed a longstanding chal-lenge.In this study,we investigated the cluster strengthening and grain refinement toughening mecha-nisms in fully oxidized AgMgNi alloys,which were internally oxidized at 800℃ for 8 h under an oxy-gen atmosphere.We found that Mg-O clusters contributed to the hardening(138 HV)and strengthening(376.9 MPa)of the AgMg alloy through solid solution strengthening effects,albeit at the expense of duc-tility.To address this limitation,we introduced Ni nanoparticles into the AgMg alloy,resulting in signifi-cant grain refinement within its microstructure.Specifically,the grain size decreased from 67.2μm in the oxidized AgMg alloy to below 6.0μm in the oxidized AgMgNi alloy containing 0.3 wt%Ni.Consequently,the toughness increased significantly,rising from toughness value of 2177.9 MJ m^(-3) in the oxidized AgMg alloy to 6186.1 MJ m^(-3) in the oxidized AgMgNi alloy,representing a remarkable 2.8-fold enhancement.Furthermore,the internally oxidized AgMgNi alloy attained a strength of up to 387.6 MPa,comparable to that of the internally oxidized AgMg alloy,thereby demonstrating the successful realization of concurrent strengthening and toughening.These results collectively offer a novel approach for the design of high-performance alloys through the synergistic combination of cluster strengthening and grain refinement toughening.展开更多
Integrating a heterogeneous structure can significantly enhance the strength-ductility synergy of composites.However,the relationship between hetero-deformation induced(HDI)strain hardening and dislocation activity ca...Integrating a heterogeneous structure can significantly enhance the strength-ductility synergy of composites.However,the relationship between hetero-deformation induced(HDI)strain hardening and dislocation activity caused by heterogeneous structures in the magnesium matrix composite remains unclear.In this study,a dual-heterogeneous TiC/AZ61 composite exhibits significantly improved plastic elongation(PEL)by nearly one time compared to uniform FG composite,meanwhile maintaining a high strength(UTS:417 MPa).This is because more severe deformation inhomogeneity in heterogeneous structure leads to more geometrically necessary dislocations(GNDs)accumulation and stronger HDI stress,resulting in higher HDI hardening compared to FG and CG composites.During the early stage of plastic deformation,the pile-up types of GND in the FG zone and CG zone are significantly different.GNDs tend to form substructures in the FG zone instead of the CG zone.They only accumulate at grain boundaries of the CG region,thereby leading to obviously increased back stress in the CG region.In the late deformation stage,the elevated HDI stress activates the new〈c+a〉dislocations in the CG region,resulting in dislocation entanglements and even the formation of substructures,further driving the high hardening in the heterogeneous composite.However,For CG composite,〈c+a〉dislocations are not activated even under large plastic strains,and only〈a〉dislocations pile up at grain boundaries and twin boundaries.Our work provides an in-depth understanding of dislocation variation and HDI hardening in heterogeneous magnesium-based composites.展开更多
Machine learning is employed to comprehensively analyze and predict the hardenability of 20CrMo steel.The hardenability dataset includes J9 and J15 hardenability values,chemical composition,and heat treatment paramete...Machine learning is employed to comprehensively analyze and predict the hardenability of 20CrMo steel.The hardenability dataset includes J9 and J15 hardenability values,chemical composition,and heat treatment parameters.Various machine learning models,including linear regression(LR),k-nearest neighbors(KNN),random forest(RF),and extreme Gradient Boosting(XGBoost),are employed to develop predictive models for the hardenability of 20CrMo steel.Among these models,the XGBoost model achieves the best performance,with coefficients of determination(R2)of 0.941 and 0.946 for predicting J9 and J15 values,respectively.The predictions fall with a±2 HRC bandwidth for 98%of J9 cases and 99%of J15 cases.Additionally,SHapley Additive exPlanations(SHAP)analysis is used to identify the key elements that significantly influence the hardenability of the 20CrMo steel.The analysis revealed that alloying elements such as Si,Cr,C,N and Mo play significant roles in hardenability.The strengths and weaknesses of various machine learning models in predicting hardenability are also discussed.展开更多
As the rapid development of railway transportation,the wear damage between wheels and rails is increasingly severe,significantly impacting the safety and efficiency of train service.A novel heavy-haul wheel(NW)steel w...As the rapid development of railway transportation,the wear damage between wheels and rails is increasingly severe,significantly impacting the safety and efficiency of train service.A novel heavy-haul wheel(NW)steel with superior rolling-slide wear resistance is presented.Additionally,the microstructure evolution and hardening mechanisms of the wheel steel after wear were analyzed by various characterization methods.The results indicate that NW wheel steel,characterized by finer pearlite lamella and low content of proeutectoid ferrite,demonstrates exceptional wear resistance under axle loads of 200 and 400 kN.Compared to CL65 steel,the wear rate of NW wheel steel is reduced by 28%and exceeds that of most reported wheel steels.After wear,the surface material of the wheel steel experiences significant deformation,forming a gradient strain layer with microstructure and hardness exhibiting gradient changes along the depth direction.The topmost material undergoes refinement and dislocation multiplication,leading to a substantial increase in surface hardness.Moreover,NW steel exhibits more severe surface dislocations and increased hardness at higher axle loads.Therefore,by controlling the pearlite content and reducing the lamellar spacing,a gradient strain layer with enhanced hardening capabilities can be achieved,thereby improving the wear resistance of the wheel material.展开更多
The Mg alloys with combination of high strength and excellent irradiation resistance are currently re-quired for research reactors.In this work,the novel Mg-3Mn-0.5Ca alloy with a high strength of over 300 MPa has bee...The Mg alloys with combination of high strength and excellent irradiation resistance are currently re-quired for research reactors.In this work,the novel Mg-3Mn-0.5Ca alloy with a high strength of over 300 MPa has been fabricated via co-addition of Mn and Ca elements.Moreover,the Xe ion implantation(300℃/4.5×10^(15)ions/cm^(2))is conducted for pure Mg,Mg-3Mn and Mg-3Mn-0.5Ca alloys.Microstruc-ture characterization shows that the number density of dislocation loops is comparable between Mg-3Mn and pure Mg,while the phase boundary of nano-Mn particles could act as the sink to absorb more Xe atoms,resulting in the abundant formation of Xe bubbles in the matrix of irradiated Mg-3Mn alloy.With further minor addition of Ca element,the formation of Xe bubbles and dislocation loops in Mg-3Mn-0.5Ca alloy has been obviously suppressed,and the abundant grain boundaries(GBs)due to grain refinement then act as the sink region for Xe precipitation.The limited number density of Xe bubbles leads to the extremely low swelling ratio in Mg-3Mn-0.5Ca alloy,∼0.08%.The result above suggests that the Mn and Ca co-addition could enhance the mechanical properties and irradiation tolerance of Mg alloys,si-multaneously.The present low-alloying strategy would provide a new design reference for novel nuclear materials.展开更多
The selection of twin variants plays a critical role in shaping the deformation texture and mechanical properties of magnesium alloys that are limited by slip systems and diverse twinning modes.In this study,we invest...The selection of twin variants plays a critical role in shaping the deformation texture and mechanical properties of magnesium alloys that are limited by slip systems and diverse twinning modes.In this study,we investigated the twin variant selection and the effect of twinning activity on the strain hardening of a hot-rolled AZ31 magnesium alloy by quasi-in-situ EBSD.Moreover,the Schmid factors and the displacement gradient tensors were computed to evaluate the activation of twin variants.The results reveal that the yield strength increased progressively after each deformation step,driven by grain subdivision and texture hardening induced by extension{1012}twinning and the Basinski effect at large strains.The nucleation and growth of the{1012}twins occurred either sequentially or simultaneously during the plastic deformation.At low plastic strains,the activation of most twin variants followed the high Schmid factor criterion while the other twin variants with lower Schmid factors were activated due to the interactions with preexisting twins characterized by high misorientation angles(around 60°).Additionally,this non-Schmid factor scenario was also attributed to low coordinated strain requirements from neighboring grains,showing the critical role of local deformation accommodation in the twinning process.These findings advance the fundamental understanding of the twin variant selection and its implications for the microstructure-property relationship in magnesium alloys for structural applications.展开更多
A newly developed P-doped CrCoNi medium-entropy alloy(MEA)provides both higher yield strength and larger uniform elongation than the conventional CrCoNi MEA,even superior tensile ductility to the other-element-doped C...A newly developed P-doped CrCoNi medium-entropy alloy(MEA)provides both higher yield strength and larger uniform elongation than the conventional CrCoNi MEA,even superior tensile ductility to the other-element-doped CrCoNi MEAs at similar yield strength levels.P segregation at grain boundaries(GBs)and dissolution inside grain interiors,together with the related lower stacking fault energy(SFE)are found in the P-doped CrCoNi MEA.Higher hetero-deformation-induced(HDI)hardening rate is observed in the P-doped CrCoNi MEA due to the grain-to-grain plastic deformation and the dynamic structural refinement by high-density stacking fault-walls(SFWs).The enhanced yield strength in the P-doped CoCrNi MEA can be attributed to the strong substitutional solid-solution strengthening by severer lattice distortion and the GB strengthening by phosphorus segregation at GBs.During the tensile deformation,the multiple SFW frames inundated with massive multi-orientational tiny planar stacking faults(SFs)between them,rather than deformation twins,are observed to induce dynamic structural refinement for forming par-allelepiped domains in the P-doped CoCrNi MEA,due to the lower SFE and even lower atomically-local SFE.These nano-sized domains with domain boundary spacing at tens of nanometers can block disloca-tion movement for strengthening on one hand,and can accumulate defects in the interiors of domains for exceptionally high hardening rate on the other hand.展开更多
The trade-offbetween strength and ductility remains a persistent obstacle in the development of advanced structural materials.In the present study,a novel dual-heterogeneous structure with a bimodal grain distribution...The trade-offbetween strength and ductility remains a persistent obstacle in the development of advanced structural materials.In the present study,a novel dual-heterogeneous structure with a bimodal grain distribution in both ferrite and austenite phases was fabricated via cold rolling and partial recrystallization annealing on solution-treated 2205 duplex stainless steel(DSS).The processed steel exhibited superior mechanical properties,with the yield strength increasing from 586 MPa to 903 MPa,and the ultimate tensile strength from 796 MPa to 1082 MPa,while maintaining a high total elongation of 35.3%.Based on in-situ electron backscatter diffraction(EBSD)and scanning electron microscope(SEM)analyses,the microstructural deformation behavior and strengthening mechanisms of the dual-heterostructured 2205 DSS were elucidated.The outstanding combination of strength and ductility was ascribed to the synergistic effects of grain refinement,dislocation strengthening,and hetero-deformation induced(HDI)strengthening.Moreover,the high ductility in DSS was attributed to the coactivation of cross-slip systems in ferrite{110}and{112}along with the single-slip systems in austenite{111}.These findings provide a new strategy for the design and development of high-strength and ultra-high-strength DSSs.展开更多
The effect of adding Cr and Mg on the microstructure and properties of Cu−Ti alloys was examined.Cu−Ti−Cr−Mg alloys were fabricated using vacuum induction melting.The microstructure and phase composition of Cu−Ti−Cr−M...The effect of adding Cr and Mg on the microstructure and properties of Cu−Ti alloys was examined.Cu−Ti−Cr−Mg alloys were fabricated using vacuum induction melting.The microstructure and phase composition of Cu−Ti−Cr−Mg alloys in different aging states were characterized.Additionally,the hardness and electrical conductivity of the materials were investigated.Results show that the precipitation pattern in Cu−Ti−Cr−Mg alloys resembled that of binary Cu−Ti alloys,with Cr and Ti forming the intermetallic compound of Cr_(2)Ti during casting.The introduction of Cr and Mg increased the hardness of the alloy.Increasing the Mg content in the Cu−Ti−Cr−Mg alloy led to grain refinement and fast nucleation of continuous precipitates during the early aging stage.Moreover,the addition of Mg impeded discontinuous precipitate growth by segregating along the precipitate surfaces.Consequently,the Cu−4Ti−0.5Cr−1Mg alloy exhibited limited discontinuous precipitates at the grain boundaries and a gradual decline in hardness during the over-aging period.展开更多
Developing high-strength and ductile metallic parts with designable shapes is an unfading research topic for material science and engineering.As a revolutionary technology,additive manufacturing(AM)pro-vides a new pat...Developing high-strength and ductile metallic parts with designable shapes is an unfading research topic for material science and engineering.As a revolutionary technology,additive manufacturing(AM)pro-vides a new pathway for producing complex-shaped metallic parts with the possibility of in situ tailoring their microstructure.However,AM is not always ideally applicable for all metals and alloys.Eutectic high entropy alloys(EHEAs)contain both the advantages of the eutectic alloys and high entropy alloys(HEAs),and EHEAs show significant potential in AM due to their excellent mechanical properties and good fluid-ity.Herein,heterogeneous and ultra-fine eutectic lamellar microstructure with directional growth along the deposition direction(DD)was obtained by adjusting the process parameters of AM to improve the strength and ductility of EHEAs.Compared with the as-cast sample,the simultaneous increment in both strength and ductility is achieved by AM.Combination of strength and ductility of the AM sample ten-sile along the DD direction(yield strength σ_(y)=1115 MPa,ultimate tensile strength σ_(UTS)=1417 MPa,ultimate tensile strain ε_(U)=23%)in this work was superior to most of the additive manufactured al-loys and comparable to the thermomechanical-treated EHEAs with the best mechanical properties.The high strength and good ductility of the AM were mainly attributed to the ultra-fine lamellar nature and fully constrained soft and hard lamellar microstructure,which produces an obvious hetero-deformation induced(HDI)strengthening and high crack buffering effect during the deformation.This work provides a new possibility to achieve high strength and ductile complex-shaped metallic parts via designing direc-tional lamellar eutectic structures by AM.展开更多
High manganese steels(HMS),known for their exceptional strength-ductility balance,are increasingly utilized in dynamic loading applications.This review examines the effects of strain rate on their mechanical propertie...High manganese steels(HMS),known for their exceptional strength-ductility balance,are increasingly utilized in dynamic loading applications.This review examines the effects of strain rate on their mechanical properties and microstructural evolution,focusing on strain rate hardening,adiabatic heating softening,and dynamic strain aging(DSA).The influence of strain rate on yield strength,ultimate tensile strength,strain hardening,and ductility is discussed,highlighting both positive and negative sensitivities across different alloy compositions and strain rate regimes.The strain rate response of various deformation mechanisms,including deformation twinning,dislocation slip,and phase transformation,is examined alongside their influence on microstructural evolution,alloy design,and industrial applications.The intricate role of DSA is also analyzed,emphasizing its contribution to strain rate sensitivity.To optimize HMS for dynamic environments,future research should focus on advanced modeling and processing techniques,in-situ characterization methods,and a deeper understanding of thermally activated processes and stacking fault energy-controlled mechanisms.This review provides insights into strain rate effects,guiding alloy design,and technological advancements of the new HMS.展开更多
Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid ...Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.展开更多
In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cycl...In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cyclic stress relaxation test,EBSD,TEM and other characterization methods were used.When the rolling temperature is 350℃,the grain size of magnesium sheets is refined to 4.32(±0.36)μm on average,and it shows an excellent combination of strength and plasticity.The tensile strength reaches 307(±8.52)MPa and the elongation is 12.73(±0.84)%.At this time,the curve of work hardening rate decreases smoothly and the degree of hardening is the lowest,and the amplitude of stress drop △σ_(p) in work softening test is the smallest with the increase of cycle times,which shows that the well coordination between work hardening and softening behavior has been achieved.Research has found that the combined effect of grain boundary strengthening and fine grain strengthening enhances the yield and tensile strength of magnesium sheets after three passes HP-ARB process at 350℃.This is attributed to the high degree of dislocation slip opening in the pyramidal surfaceand<c+a>,which not only coordinates the c-axis strain of the entire grain,but also promotes the slip transfer of dislocations in the fine-grained region,significantly improving the elongation of the sheets.This study provides a new idea for the forming and manufacturing of high performance magnesium alloy sheets.展开更多
文摘In this research, the dynamic recrystallization （DRX） behavior of an as-cast precipitation hardenable （PH） stainless steel was investigated by conducting hot compression tests at temperatures between 950-1150℃ and under strain rates of 0.001-1 s^-1. The flow stress curves show that the DRX is responsible for flow softening during hot compression. The effects of temperature and strain rate on the strain and stress corresponding to peak point （εp and σp） of flow curve were analyzed individually. It is realized that, they increase with strain rate and decrease with temperature. The relationship between Zener-Hollomon parameter （Z） and εp was investigated and the equation of εp=4.3×10^-4^0.14 was proposed. The strain for the maximum rate of DRX （εmax） was determined under different deformation conditions. Therefore, it is realized that it increases with Z parameter and vise versa. On the basis of obtained results, the equation of εmax=9.5 × 10^-4Z0.12 was proposed.
基金Project supported by the National Natural Science Foundation of China(Nos.12172149,12172151,and 12202378)the MOE Key Laboratory of Fututer Intelligent Manufacturing Technologies for High-End Equipment of China(No.FIMFYUST-2025B07)+1 种基金the Guangzhou Municipal Bureau of Science and Technology of China(No.SL2023A04J01461)the Ministry of Science and Technology of China(No.G20221990122)。
文摘This study focuses on a new and high-efficiency approach in a unified sense of accurately simulating strength-degrading effects for geomaterials,including non-symmetric hardening-to-softening effects in tension and compression as well as non-symmetric tensile and compressive stiffness-degrading effects during unloading.It is intended to bypass both modeling and numerical complexities involved in existing approaches.To this goal,new elastoplastic equations are established with new numerical techniques.With a decoupling technique of treating tension-compression asymmetry,the foregoing complex effects are automatically incorporated as inherent response features of the new elastoplastic equations,thus bypassing usual modeling complexities.A new numerical technique of renormalizing piecewise spline functions is introduced to resolve the central yet tough issue of obtaining accurate and unified expressions for the tensile and compressive strength functions,thus bypassing usual numerical complexities and uncertainties in treating numerous unknown parameters and multiple ad hoc criteria.As such,the new approach is not only of wide applicability for various geomaterials but also of high computational efficiency with no more than three adjustable parameters.Toward validating the efficacy of the new approach,numerical examples for granite,salt rock,and sandstone-concrete combined body as well as plain concrete,high-performance concrete,and ultrahigh-performance concrete are presented by comparing model predictions with multiple data sets for strength-degrading effects in tension and compression.
基金supported by the National Key Research and Development Program(Grant No.2024YFB3714200)the National Natural Science Foundation of China(Grant Nos.52173305,52233017,52203384,U244120568 and U2441261)+1 种基金the Key Program of the Chinese Academy of Sciences(Grant No.RCJJ-145-24-40)LingChuang Research Project of China National Nuclear Corporation,and Special Funds for Science and Technology Planning of Jiangsu Province(No.BZ2024059).
文摘Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed.For all of water,oil,air and furnace cooling,there is almost-complete martensite with the favorable hardenability.The increase in cooling rate mainly increases the density of dislocation and residual strain in the as-solution annealed matrix.After aging treatment,the cooling rate dominates the ratio of high-angle grain boundaries(HAGBs)instead of the size of martensite blocks.The ratio of HAGBs continuously increases with the decreased cooling rate,while the width of blocks maintains 2.40-2.49μm.Meanwhile,more reversed austenite distributes at the martensite sub-grain boundaries.By comparison,the increased rate of water cooling contributes to a favorable precipitation of NiAl with fine size and dispersive distribution caused by more accumulated internal defects of vacancies and dislocations.With the decrease of cooling rate,NiAl precipitates exhibits a similar diameter of~7 nm while a larger inter-particle distance of~22 nm.In the case of low cooling rate(oil,air and furnace),the stable precipitation strengthening effect contributes to a high yield strength of~1.3 GPa and ultimate tensile strength of~1.4 GPa.The high-ratio HAGBs,reversed austenite and NiAl precipitates with larger-interparticle distance synergistically improve the impact toughness(V-notched Charpy impact energy of 100-110 J).
基金supported in part by National R&D Program for Major Research Instruments of China(No.62027814)。
文摘This study focuses on a 60 V trench MOSFET device designed for operation in space radiation environments.By increasing the bulk region concentration and placing the etched gate trench after the P+implantation process,we successfully reduced the threshold voltage shift from 6.5 to 2.2 V under a total dose of 400 krad(Si)^(60)Co,allowing the device to operate normally.Structurally,by embedding the source metal in the active and terminal regions,the device demonstrated current degradation without experiencing single-event burnout when subjected to a drain voltage of 60 V and a linear energy transfer value of 75.4 MeV·cm^(2)∕mg from tantalum-ion incidence.TCAD simulations verified that the embedded source metal effectively suppressed parasitic transistor conduction and eliminated the base-region expansion effect,thereby lowering the maximum temperature from 8000 to 1400 K.The irradiation effects of the embedded source metal in the terminal region were also investigated,which can improve the reverse recovery and ensure that the terminal metal does not melt prematurely,thereby significantly enhancing the radiation hardness of the device.
基金supported by the National Key R&D Program of China (No. 2018YFA0707300)the National Natural Science Foundation of China (No. 52374376)the Introduction Plan for High end Foreign Experts, China (No. G2023105001L)。
文摘Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding strength in titanium/stainless steel laminated composites were investigated.Results indicate that the hardened layer reduces the interfacial bonding strength from over 261 MPa to less than 204 MPa.During the cold roll-bonding process,the hardened layer fractures,leading to the formation of multi-scale cracks that are difficult for the stainless steel to fill.This not only hinders the development of an interlocking interface but also leads to the presence of numerous microcracks and hardened blocks along the nearly straight interface,consequently weakening the interfacial bonding strength.In metals with high work hardening rates,the conventional approach of enhancing interface interlocking and improving interfacial bonding strength by using a surface-hardened layer becomes less effective.
基金supported by Poongsan-KAIST Future Research Center Projectthe fund support provided by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(Grant No.2023R1A2C2005661)。
文摘This study presents a machine learning-based method for predicting fragment velocity distribution in warhead fragmentation under explosive loading condition.The fragment resultant velocities are correlated with key design parameters including casing dimensions and detonation positions.The paper details the finite element analysis for fragmentation,the characterizations of the dynamic hardening and fracture models,the generation of comprehensive datasets,and the training of the ANN model.The results show the influence of casing dimensions on fragment velocity distributions,with the tendencies indicating increased resultant velocity with reduced thickness,increased length and diameter.The model's predictive capability is demonstrated through the accurate predictions for both training and testing datasets,showing its potential for the real-time prediction of fragmentation performance.
基金Derek Elsworth acknowledges the support from a Gledden Visiting Fellowship from the Institute of Advanced Studies at the University of Western Australia,Australia,and the G.Albert Shoemaker Endowment at Pennsylvania State University,USA.
文摘Triggered seismicity is a key hazard where fluids are injected or withdrawn from the subsurface and may impact permeability. Understanding the mechanisms that control fluid injection-triggered seismicity allows its mitigation. Key controls on seismicity are defined in terms of fault and fracture strength, second-order frictional response and stability, and competing fluid-driven mechanisms for arrest. We desire to constrain maximum event magnitudes in triggered earthquakes by relating pre-existing critical stresses to fluid injection volume to explain why some recorded events are significantly larger than anticipated seismic moment thresholds. This formalism is consistent with several uncharacteristically large fluid injection-triggered earthquakes. Such methods of reactivating fractures and faults by hydraulic stimulation in shear or tensile fracturing are routinely used to create permeability in the subsurface. Microearthquakes (MEQs) generated by such stimulations can be used to diagnose permeability evolution. Although high-fidelity data sets are scarce, the EGS-Collab and Utah FORGE hydraulic stimulation field demonstration projects provide high-fidelity data sets that concurrently track permeability evolution and triggered seismicity. Machine learning deciphers the principal features of MEQs and the resulting permeability evolution that best track permeability changes – with transfer learning methods allowing robust predictions across multiple eological settings. Changes in permeability at reactivated fractures in both shear and extensional modes suggest that permeability change (Δk) scales with the seismic moment (M) of individual MEQs as Δk∝M. This scaling relation is exact at early times but degrades with successive MEQs, but provides a method for characterizing crustal permeability evolution using MEQs, alone. Importantly, we quantify for the first time the role of prestress in defining the elevated magnitude and seismic moment of fluid injection-triggered events, and demonstrate that such MEQs can also be used as diagnostic in quantifying permeability evolution in the crust.
基金supported by the National Natural Science Foundation of China(Nos.51977027 and 51967008)the Scientific and Technological Project of Yunnan Precious Metals Lab-oratory(Nos.YPML-2023050250 and YPML-2022050206).
文摘The pursuit of Ag-based alloys with both high strength and toughness has posed a longstanding chal-lenge.In this study,we investigated the cluster strengthening and grain refinement toughening mecha-nisms in fully oxidized AgMgNi alloys,which were internally oxidized at 800℃ for 8 h under an oxy-gen atmosphere.We found that Mg-O clusters contributed to the hardening(138 HV)and strengthening(376.9 MPa)of the AgMg alloy through solid solution strengthening effects,albeit at the expense of duc-tility.To address this limitation,we introduced Ni nanoparticles into the AgMg alloy,resulting in signifi-cant grain refinement within its microstructure.Specifically,the grain size decreased from 67.2μm in the oxidized AgMg alloy to below 6.0μm in the oxidized AgMgNi alloy containing 0.3 wt%Ni.Consequently,the toughness increased significantly,rising from toughness value of 2177.9 MJ m^(-3) in the oxidized AgMg alloy to 6186.1 MJ m^(-3) in the oxidized AgMgNi alloy,representing a remarkable 2.8-fold enhancement.Furthermore,the internally oxidized AgMgNi alloy attained a strength of up to 387.6 MPa,comparable to that of the internally oxidized AgMg alloy,thereby demonstrating the successful realization of concurrent strengthening and toughening.These results collectively offer a novel approach for the design of high-performance alloys through the synergistic combination of cluster strengthening and grain refinement toughening.
基金support from the National Natural Science Foundation of China(No:52061040)China Postdoctoral Science Foundation(No:2021M692512)+1 种基金Opening Project of Material Corrosion and Protection Key Laboratory of Sichuan Province(No:2023CL01)Open Projects of Key Laboratory of Advanced Technologies of Materials,Ministry of Education China,Southwest Jiaotong University(No:KLATM202003).
文摘Integrating a heterogeneous structure can significantly enhance the strength-ductility synergy of composites.However,the relationship between hetero-deformation induced(HDI)strain hardening and dislocation activity caused by heterogeneous structures in the magnesium matrix composite remains unclear.In this study,a dual-heterogeneous TiC/AZ61 composite exhibits significantly improved plastic elongation(PEL)by nearly one time compared to uniform FG composite,meanwhile maintaining a high strength(UTS:417 MPa).This is because more severe deformation inhomogeneity in heterogeneous structure leads to more geometrically necessary dislocations(GNDs)accumulation and stronger HDI stress,resulting in higher HDI hardening compared to FG and CG composites.During the early stage of plastic deformation,the pile-up types of GND in the FG zone and CG zone are significantly different.GNDs tend to form substructures in the FG zone instead of the CG zone.They only accumulate at grain boundaries of the CG region,thereby leading to obviously increased back stress in the CG region.In the late deformation stage,the elevated HDI stress activates the new〈c+a〉dislocations in the CG region,resulting in dislocation entanglements and even the formation of substructures,further driving the high hardening in the heterogeneous composite.However,For CG composite,〈c+a〉dislocations are not activated even under large plastic strains,and only〈a〉dislocations pile up at grain boundaries and twin boundaries.Our work provides an in-depth understanding of dislocation variation and HDI hardening in heterogeneous magnesium-based composites.
基金supported by the Key scientific and technological project plan of Hebei Iron and Steel Group(No.HG2023235).
文摘Machine learning is employed to comprehensively analyze and predict the hardenability of 20CrMo steel.The hardenability dataset includes J9 and J15 hardenability values,chemical composition,and heat treatment parameters.Various machine learning models,including linear regression(LR),k-nearest neighbors(KNN),random forest(RF),and extreme Gradient Boosting(XGBoost),are employed to develop predictive models for the hardenability of 20CrMo steel.Among these models,the XGBoost model achieves the best performance,with coefficients of determination(R2)of 0.941 and 0.946 for predicting J9 and J15 values,respectively.The predictions fall with a±2 HRC bandwidth for 98%of J9 cases and 99%of J15 cases.Additionally,SHapley Additive exPlanations(SHAP)analysis is used to identify the key elements that significantly influence the hardenability of the 20CrMo steel.The analysis revealed that alloying elements such as Si,Cr,C,N and Mo play significant roles in hardenability.The strengths and weaknesses of various machine learning models in predicting hardenability are also discussed.
基金supported by the Key Project of Science and Technology in Anhui Province(No.202003a05020038)the Major Consulting Project of Chinese Academy of Engineering(No.ZGZ201812–03)。
文摘As the rapid development of railway transportation,the wear damage between wheels and rails is increasingly severe,significantly impacting the safety and efficiency of train service.A novel heavy-haul wheel(NW)steel with superior rolling-slide wear resistance is presented.Additionally,the microstructure evolution and hardening mechanisms of the wheel steel after wear were analyzed by various characterization methods.The results indicate that NW wheel steel,characterized by finer pearlite lamella and low content of proeutectoid ferrite,demonstrates exceptional wear resistance under axle loads of 200 and 400 kN.Compared to CL65 steel,the wear rate of NW wheel steel is reduced by 28%and exceeds that of most reported wheel steels.After wear,the surface material of the wheel steel experiences significant deformation,forming a gradient strain layer with microstructure and hardness exhibiting gradient changes along the depth direction.The topmost material undergoes refinement and dislocation multiplication,leading to a substantial increase in surface hardness.Moreover,NW steel exhibits more severe surface dislocations and increased hardness at higher axle loads.Therefore,by controlling the pearlite content and reducing the lamellar spacing,a gradient strain layer with enhanced hardening capabilities can be achieved,thereby improving the wear resistance of the wheel material.
基金the National Natural Science Foun-dation of China(Nos.U2241235,U2167213 and U2067218)the Project funded by the Science&Technology Department of Sichuan Province(No.21MZGC0400,No.2022JDJQ0021)+3 种基金the China National Nuclear Corporation(CNNC)Science Fund for Talented Young Scholars(No.CNNC-2021-31)the Funds of Science and Technol-ogy on Reactor Fuel and Materials Laboratory(No.6142A06190510)the fund from the Fundamental Research Funds for the Cen-tral Universities(No.N2202020)XingLiao Talent Plan(No.XLYC2203202).
文摘The Mg alloys with combination of high strength and excellent irradiation resistance are currently re-quired for research reactors.In this work,the novel Mg-3Mn-0.5Ca alloy with a high strength of over 300 MPa has been fabricated via co-addition of Mn and Ca elements.Moreover,the Xe ion implantation(300℃/4.5×10^(15)ions/cm^(2))is conducted for pure Mg,Mg-3Mn and Mg-3Mn-0.5Ca alloys.Microstruc-ture characterization shows that the number density of dislocation loops is comparable between Mg-3Mn and pure Mg,while the phase boundary of nano-Mn particles could act as the sink to absorb more Xe atoms,resulting in the abundant formation of Xe bubbles in the matrix of irradiated Mg-3Mn alloy.With further minor addition of Ca element,the formation of Xe bubbles and dislocation loops in Mg-3Mn-0.5Ca alloy has been obviously suppressed,and the abundant grain boundaries(GBs)due to grain refinement then act as the sink region for Xe precipitation.The limited number density of Xe bubbles leads to the extremely low swelling ratio in Mg-3Mn-0.5Ca alloy,∼0.08%.The result above suggests that the Mn and Ca co-addition could enhance the mechanical properties and irradiation tolerance of Mg alloys,si-multaneously.The present low-alloying strategy would provide a new design reference for novel nuclear materials.
文摘The selection of twin variants plays a critical role in shaping the deformation texture and mechanical properties of magnesium alloys that are limited by slip systems and diverse twinning modes.In this study,we investigated the twin variant selection and the effect of twinning activity on the strain hardening of a hot-rolled AZ31 magnesium alloy by quasi-in-situ EBSD.Moreover,the Schmid factors and the displacement gradient tensors were computed to evaluate the activation of twin variants.The results reveal that the yield strength increased progressively after each deformation step,driven by grain subdivision and texture hardening induced by extension{1012}twinning and the Basinski effect at large strains.The nucleation and growth of the{1012}twins occurred either sequentially or simultaneously during the plastic deformation.At low plastic strains,the activation of most twin variants followed the high Schmid factor criterion while the other twin variants with lower Schmid factors were activated due to the interactions with preexisting twins characterized by high misorientation angles(around 60°).Additionally,this non-Schmid factor scenario was also attributed to low coordinated strain requirements from neighboring grains,showing the critical role of local deformation accommodation in the twinning process.These findings advance the fundamental understanding of the twin variant selection and its implications for the microstructure-property relationship in magnesium alloys for structural applications.
基金supported by the National Key R&D Program of China(No.2019YFA0209902)the Natural Science Foundation of China(Nos.52071326,52192593,51601204)+1 种基金the NSFC Basic Science Center Program for Multiscale Problems in Nonlinear Mechanics(No.11988102)the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDB22040503).
文摘A newly developed P-doped CrCoNi medium-entropy alloy(MEA)provides both higher yield strength and larger uniform elongation than the conventional CrCoNi MEA,even superior tensile ductility to the other-element-doped CrCoNi MEAs at similar yield strength levels.P segregation at grain boundaries(GBs)and dissolution inside grain interiors,together with the related lower stacking fault energy(SFE)are found in the P-doped CrCoNi MEA.Higher hetero-deformation-induced(HDI)hardening rate is observed in the P-doped CrCoNi MEA due to the grain-to-grain plastic deformation and the dynamic structural refinement by high-density stacking fault-walls(SFWs).The enhanced yield strength in the P-doped CoCrNi MEA can be attributed to the strong substitutional solid-solution strengthening by severer lattice distortion and the GB strengthening by phosphorus segregation at GBs.During the tensile deformation,the multiple SFW frames inundated with massive multi-orientational tiny planar stacking faults(SFs)between them,rather than deformation twins,are observed to induce dynamic structural refinement for forming par-allelepiped domains in the P-doped CoCrNi MEA,due to the lower SFE and even lower atomically-local SFE.These nano-sized domains with domain boundary spacing at tens of nanometers can block disloca-tion movement for strengthening on one hand,and can accumulate defects in the interiors of domains for exceptionally high hardening rate on the other hand.
基金supported by the National Natural Science Foundation of China(Nos.U1960115 and U21A20116)the Fundamental Research Funds for the Central Universities(No.N232405-10)Special thanks are due to the instrumental and data analysis from Analytical and Testing Center,Northeastern University.
文摘The trade-offbetween strength and ductility remains a persistent obstacle in the development of advanced structural materials.In the present study,a novel dual-heterogeneous structure with a bimodal grain distribution in both ferrite and austenite phases was fabricated via cold rolling and partial recrystallization annealing on solution-treated 2205 duplex stainless steel(DSS).The processed steel exhibited superior mechanical properties,with the yield strength increasing from 586 MPa to 903 MPa,and the ultimate tensile strength from 796 MPa to 1082 MPa,while maintaining a high total elongation of 35.3%.Based on in-situ electron backscatter diffraction(EBSD)and scanning electron microscope(SEM)analyses,the microstructural deformation behavior and strengthening mechanisms of the dual-heterostructured 2205 DSS were elucidated.The outstanding combination of strength and ductility was ascribed to the synergistic effects of grain refinement,dislocation strengthening,and hetero-deformation induced(HDI)strengthening.Moreover,the high ductility in DSS was attributed to the coactivation of cross-slip systems in ferrite{110}and{112}along with the single-slip systems in austenite{111}.These findings provide a new strategy for the design and development of high-strength and ultra-high-strength DSSs.
基金supported by the National Natural Science Foundation of China(No.52201226)Fundamental Research Program of Shanxi Province,China(No.202103021223036)+1 种基金the Key Scientific Research Project in Shanxi Province,China(No.202102050201007)the special fund for Science and Technology Innovation Teams of Shanxi Province,China(No.202204051001004)。
文摘The effect of adding Cr and Mg on the microstructure and properties of Cu−Ti alloys was examined.Cu−Ti−Cr−Mg alloys were fabricated using vacuum induction melting.The microstructure and phase composition of Cu−Ti−Cr−Mg alloys in different aging states were characterized.Additionally,the hardness and electrical conductivity of the materials were investigated.Results show that the precipitation pattern in Cu−Ti−Cr−Mg alloys resembled that of binary Cu−Ti alloys,with Cr and Ti forming the intermetallic compound of Cr_(2)Ti during casting.The introduction of Cr and Mg increased the hardness of the alloy.Increasing the Mg content in the Cu−Ti−Cr−Mg alloy led to grain refinement and fast nucleation of continuous precipitates during the early aging stage.Moreover,the addition of Mg impeded discontinuous precipitate growth by segregating along the precipitate surfaces.Consequently,the Cu−4Ti−0.5Cr−1Mg alloy exhibited limited discontinuous precipitates at the grain boundaries and a gradual decline in hardness during the over-aging period.
基金supported by the National Key Re-search and Development Program of China(No.2024YFC2816500)the National Natural Science Foundation of China(Nos.U2341261 and 52471121)the Fundamental Research Funds for the Cen-tral Universities(No.DUT24RC(3)107).
文摘Developing high-strength and ductile metallic parts with designable shapes is an unfading research topic for material science and engineering.As a revolutionary technology,additive manufacturing(AM)pro-vides a new pathway for producing complex-shaped metallic parts with the possibility of in situ tailoring their microstructure.However,AM is not always ideally applicable for all metals and alloys.Eutectic high entropy alloys(EHEAs)contain both the advantages of the eutectic alloys and high entropy alloys(HEAs),and EHEAs show significant potential in AM due to their excellent mechanical properties and good fluid-ity.Herein,heterogeneous and ultra-fine eutectic lamellar microstructure with directional growth along the deposition direction(DD)was obtained by adjusting the process parameters of AM to improve the strength and ductility of EHEAs.Compared with the as-cast sample,the simultaneous increment in both strength and ductility is achieved by AM.Combination of strength and ductility of the AM sample ten-sile along the DD direction(yield strength σ_(y)=1115 MPa,ultimate tensile strength σ_(UTS)=1417 MPa,ultimate tensile strain ε_(U)=23%)in this work was superior to most of the additive manufactured al-loys and comparable to the thermomechanical-treated EHEAs with the best mechanical properties.The high strength and good ductility of the AM were mainly attributed to the ultra-fine lamellar nature and fully constrained soft and hard lamellar microstructure,which produces an obvious hetero-deformation induced(HDI)strengthening and high crack buffering effect during the deformation.This work provides a new possibility to achieve high strength and ductile complex-shaped metallic parts via designing direc-tional lamellar eutectic structures by AM.
基金supported by the National Natural Science Foundation(No.52101128)the Jiangsu Provincial Key Research and Development Program(No.BE023059)+1 种基金Postdoctoral Science Foundation(No.2022M710021)the Northeastern University Postdoctoral Research Fund(No.20220202)of China。
文摘High manganese steels(HMS),known for their exceptional strength-ductility balance,are increasingly utilized in dynamic loading applications.This review examines the effects of strain rate on their mechanical properties and microstructural evolution,focusing on strain rate hardening,adiabatic heating softening,and dynamic strain aging(DSA).The influence of strain rate on yield strength,ultimate tensile strength,strain hardening,and ductility is discussed,highlighting both positive and negative sensitivities across different alloy compositions and strain rate regimes.The strain rate response of various deformation mechanisms,including deformation twinning,dislocation slip,and phase transformation,is examined alongside their influence on microstructural evolution,alloy design,and industrial applications.The intricate role of DSA is also analyzed,emphasizing its contribution to strain rate sensitivity.To optimize HMS for dynamic environments,future research should focus on advanced modeling and processing techniques,in-situ characterization methods,and a deeper understanding of thermally activated processes and stacking fault energy-controlled mechanisms.This review provides insights into strain rate effects,guiding alloy design,and technological advancements of the new HMS.
基金financially supported by the National Natural Science Foundation of China(No.51771125)the Sichuan Province Science and Technology Support Program(No.2020YFG0102)。
文摘Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.
基金supported by the Natural Science Foundation of Heilongjiang Province(No.JQ2022E004).
文摘In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cyclic stress relaxation test,EBSD,TEM and other characterization methods were used.When the rolling temperature is 350℃,the grain size of magnesium sheets is refined to 4.32(±0.36)μm on average,and it shows an excellent combination of strength and plasticity.The tensile strength reaches 307(±8.52)MPa and the elongation is 12.73(±0.84)%.At this time,the curve of work hardening rate decreases smoothly and the degree of hardening is the lowest,and the amplitude of stress drop △σ_(p) in work softening test is the smallest with the increase of cycle times,which shows that the well coordination between work hardening and softening behavior has been achieved.Research has found that the combined effect of grain boundary strengthening and fine grain strengthening enhances the yield and tensile strength of magnesium sheets after three passes HP-ARB process at 350℃.This is attributed to the high degree of dislocation slip opening in the pyramidal surfaceand<c+a>,which not only coordinates the c-axis strain of the entire grain,but also promotes the slip transfer of dislocations in the fine-grained region,significantly improving the elongation of the sheets.This study provides a new idea for the forming and manufacturing of high performance magnesium alloy sheets.
