The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bol...The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bolt, grout, rock mass and bond interface,considering the shear properties of the grout and contact interface bonding behavior. In this case, the interfacial shear stress of the grout and rock mass and the bolt axial force are obtained under pull-out and normal working conditions. The results show that the peak shear stress of the interface with the shear deformation of the bond interface is significantly lower than that without it when the pull-out force is applied. When designing bolt parameters of grade IV and V rock mass, the relative deformation between the rock mass and anchor should be considered, with a “unimodal” to “bimodal” shear stress distribution.In the case of a low elastic modulus of rock masses,both the shear stress concentration and distribution range are obvious, and the neutral point is near the bolt head. As the elastic modulus increases, the shear stress concentration and distribution range are reduced, and the neutral point moves towards the distal end. As a result, the optimum length of fulllength grouted bolts can be determined by in-situ pull-out tests and decreases with the increased elastic modulus of the rock mass.展开更多
To analyze the effects of a time-varying viscosity on the penetration length of grouting,in this study cement slur-ries with varying water-cement ratios have been investigated using the Bingham’sfluidflow equation and ...To analyze the effects of a time-varying viscosity on the penetration length of grouting,in this study cement slur-ries with varying water-cement ratios have been investigated using the Bingham’sfluidflow equation and a dis-crete element method.Afluid-solid coupling numerical model has been introduced accordingly,and its accuracy has been validated through comparison of theoretical and numerical solutions.For different fracture forms(a single fracture,a branch fracture,and a fracture network),the influence of the time-varying viscosity on the slurry length range has been investigated,considering the change in the fracture aperture.The results show that under different fracture forms and the same grouting process conditions,the influence of the time-varying viscosity on the seepage length is 0.350 m.展开更多
Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cabl...Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts,a new laboratory short encapsulation pull test(LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass,using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore,the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/rock interface.Based on this apparatus,a series of pull tests were undertaken using the MW9 modified bulb cable bolt.Various parameters including embedment length,test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm,there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm,the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material,failure always took place along the grout/rock interface. Interestingly,increasing the borehole diameter from 42 to 52 m in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.展开更多
The present study examines the working conditions of fully grouted bolts used for the construction and expansion of high slopes.On the basis of a pull out destructive test,the work load and the ultimate load are obtai...The present study examines the working conditions of fully grouted bolts used for the construction and expansion of high slopes.On the basis of a pull out destructive test,the work load and the ultimate load are obtained on site,and the Flac3d numerical simulation method is employed to determine the axial force distribution and the effective anchor length.The test results show that(1)the Q-S(load-displacement)curve of the bolt displays a certain degree of deformation coupled with the creep of the surrounding rock;(2)the working load of the bolt is closely related to the sliding deformation trend of the slope,while the ultimate load depends on the design parameters of the bolt and the lithology of the slope;(3)the distribution of bolt axial force is characterized by a single peak along the bolt length and the effective anchorage length of the bolt is 3 m;(4)after 20 years,the bolt’s ultimate load has a maximum loss of 31.94%.展开更多
基金funded by the Natural Science Foundation of China(Grants Nos.52179113,42207199,41831278)。
文摘The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bolt, grout, rock mass and bond interface,considering the shear properties of the grout and contact interface bonding behavior. In this case, the interfacial shear stress of the grout and rock mass and the bolt axial force are obtained under pull-out and normal working conditions. The results show that the peak shear stress of the interface with the shear deformation of the bond interface is significantly lower than that without it when the pull-out force is applied. When designing bolt parameters of grade IV and V rock mass, the relative deformation between the rock mass and anchor should be considered, with a “unimodal” to “bimodal” shear stress distribution.In the case of a low elastic modulus of rock masses,both the shear stress concentration and distribution range are obvious, and the neutral point is near the bolt head. As the elastic modulus increases, the shear stress concentration and distribution range are reduced, and the neutral point moves towards the distal end. As a result, the optimum length of fulllength grouted bolts can be determined by in-situ pull-out tests and decreases with the increased elastic modulus of the rock mass.
基金supported by the National Natural Science Foundation of China(Grant Numbers:U22A20234,42277170)the Key Research and Development Project of Hubei Province(Grant Number:2020BCB073).
文摘To analyze the effects of a time-varying viscosity on the penetration length of grouting,in this study cement slur-ries with varying water-cement ratios have been investigated using the Bingham’sfluidflow equation and a dis-crete element method.Afluid-solid coupling numerical model has been introduced accordingly,and its accuracy has been validated through comparison of theoretical and numerical solutions.For different fracture forms(a single fracture,a branch fracture,and a fracture network),the influence of the time-varying viscosity on the slurry length range has been investigated,considering the change in the fracture aperture.The results show that under different fracture forms and the same grouting process conditions,the influence of the time-varying viscosity on the seepage length is 0.350 m.
文摘Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts,a new laboratory short encapsulation pull test(LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass,using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore,the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/rock interface.Based on this apparatus,a series of pull tests were undertaken using the MW9 modified bulb cable bolt.Various parameters including embedment length,test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm,there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm,the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material,failure always took place along the grout/rock interface. Interestingly,increasing the borehole diameter from 42 to 52 m in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.
基金The National Key Research and Development Project(2018YFC1504801)the National Nature Science Foundation of China(41272285)the Transportation Technology Key Project of Shandong Province(JHLYDKY2).
文摘The present study examines the working conditions of fully grouted bolts used for the construction and expansion of high slopes.On the basis of a pull out destructive test,the work load and the ultimate load are obtained on site,and the Flac3d numerical simulation method is employed to determine the axial force distribution and the effective anchor length.The test results show that(1)the Q-S(load-displacement)curve of the bolt displays a certain degree of deformation coupled with the creep of the surrounding rock;(2)the working load of the bolt is closely related to the sliding deformation trend of the slope,while the ultimate load depends on the design parameters of the bolt and the lithology of the slope;(3)the distribution of bolt axial force is characterized by a single peak along the bolt length and the effective anchorage length of the bolt is 3 m;(4)after 20 years,the bolt’s ultimate load has a maximum loss of 31.94%.
