Pulse-like ground motions are capable of inflicting significant damage to structures. Efficient classification of pulse-like ground motion is of great importance when performing the seismic assessment in near-fault re...Pulse-like ground motions are capable of inflicting significant damage to structures. Efficient classification of pulse-like ground motion is of great importance when performing the seismic assessment in near-fault regions. In this study, a new method for identifying the velocity pulses is proposed, based on different trends of two parameters: the short-time energy and the short-time zero crossing rate of a ground motion record. A new pulse indicator, the relative energy zero ratio(REZR), is defined to qualitatively identify pulse-like features. The threshold for pulse-like ground motions is derived and compared with two other identification methods through statistical analysis. The proposed procedure not only shows good accuracy and efficiency when identifying pulse-like ground motions but also exhibits good performance for classifying records with high-frequency noise and discontinuous pulses. The REZR method does not require a waveform formula to express and fit the potential velocity pulses;it is a purely signal-based classification method. Finally, the proposed procedure is used to evaluate the contribution of pulse-like motions to the total input energy of a seismic record, which dramatically increases the seismic damage potential.展开更多
In general, the seismic response analysis in earthquake engineering assumes that the vibration parameters of the target and the contact surface of the external media are identical,i. e., single point input. However, e...In general, the seismic response analysis in earthquake engineering assumes that the vibration parameters of the target and the contact surface of the external media are identical,i. e., single point input. However, earthquake energy has an attenuation phenomenon in wave propagation,so a wide range of soil slopes and the external medium contact surface of different input points on motion are not identical. If we consider single point input only, it may not correspond with reality, so it is necessary to carry out research on multi-point input methods. Based on the 2-D slope model,single-point input and multi-point input are performed respectively to analyze and compare their similarities and differences in the perspectives of the characteristics of seismic response of soil layer and plastic zone distribution to provide a reference for the seismic design of slopes. The results show that in the perspective of soil seismic response analysis,the peak acceleration output and peak velocity output under multi-point input are greater than the peak values under single point input at the same monitoring point,the peak appearing time is also earlier than that of the single point input; in terms of the plastic zone distribution,the multi-point effect is manifested as the presence of more obvious tensile shear failures; in the perspective of safety coefficient,the safety coefficient under each multi-point input is smaller than that of single point input,a difference of about 7 % or so. In summary,multi-point input is more reasonable and practical than single point input,so multi-point input should be considered in seismic design.展开更多
There are two models in use today to analyze structural responses when subjected to earthquake ground motions, the Displacement Input Model （DIM） and the Acceleration Input Model （AIM）. The time steps used in dire...There are two models in use today to analyze structural responses when subjected to earthquake ground motions, the Displacement Input Model （DIM） and the Acceleration Input Model （AIM）. The time steps used in direct integration methods for these models are analyzed to examine the suitability of DIM. Numerical results are presented and show that the time-step for DIM is about the same as for AIM, and achieves the same accuracy. This is contrary to previous research that reported that there are several sources of numerical errors associated with the direct application of earthquake displacement loading, and a very small time step is required to define the displacement record and to integrate the dynamic equilibrium equation. It is shown in this paper that DIM is as accurate and suitable as, if not more than, AIM for analyzing the response of a structure to uniformly distributed and spatially varying ground motions.展开更多
Based on 266 strong ground motion records, an attenuation relationship was developed for both absolute and relative input energy spectra. The comparison of the two kinds of input energy spectra constructed from the at...Based on 266 strong ground motion records, an attenuation relationship was developed for both absolute and relative input energy spectra. The comparison of the two kinds of input energy spectra constructed from the attenuation relationship was made in this paper. The results show that there is little difference between the absolute input energy spectra and relative input energy spectra at the periods of 0.5-1.0 s for elastic systems and at the period of 0.5 s for inelastic systems. The absolute input energy spectra are much larger than relative input energy spectra in very short period range but some less than relative input energy spectra in long period range. It is also found that the ductility factor has a significant effect on both absolute and relative input energy spectra. The absolute input energy spectra increase with the increasing of ductility factor in the period range of less than 0.3 s but decrease in the period range of larger than 0.3 s. The absolute input energy spectra for different ductility factor are almost equivalent at the period about 0.3 s, but for relative input energy spectra, the period is about 0.5 s. The effect of ductility on the relative input energy spectra in the short period range is much larger than that on the absolute input energy spectra, especially on the softer site class.展开更多
基金Supported by:National Natural Science Foundation of China under Grant Nos.51378341,51427901 and 51678407National Key Research and Development Program under Grant No.2016YFC0701108
文摘Pulse-like ground motions are capable of inflicting significant damage to structures. Efficient classification of pulse-like ground motion is of great importance when performing the seismic assessment in near-fault regions. In this study, a new method for identifying the velocity pulses is proposed, based on different trends of two parameters: the short-time energy and the short-time zero crossing rate of a ground motion record. A new pulse indicator, the relative energy zero ratio(REZR), is defined to qualitatively identify pulse-like features. The threshold for pulse-like ground motions is derived and compared with two other identification methods through statistical analysis. The proposed procedure not only shows good accuracy and efficiency when identifying pulse-like ground motions but also exhibits good performance for classifying records with high-frequency noise and discontinuous pulses. The REZR method does not require a waveform formula to express and fit the potential velocity pulses;it is a purely signal-based classification method. Finally, the proposed procedure is used to evaluate the contribution of pulse-like motions to the total input energy of a seismic record, which dramatically increases the seismic damage potential.
基金funded by the Program of China Earthquake Science Data Sharing Platform and the Youth Fund(17404031570521)
文摘In general, the seismic response analysis in earthquake engineering assumes that the vibration parameters of the target and the contact surface of the external media are identical,i. e., single point input. However, earthquake energy has an attenuation phenomenon in wave propagation,so a wide range of soil slopes and the external medium contact surface of different input points on motion are not identical. If we consider single point input only, it may not correspond with reality, so it is necessary to carry out research on multi-point input methods. Based on the 2-D slope model,single-point input and multi-point input are performed respectively to analyze and compare their similarities and differences in the perspectives of the characteristics of seismic response of soil layer and plastic zone distribution to provide a reference for the seismic design of slopes. The results show that in the perspective of soil seismic response analysis,the peak acceleration output and peak velocity output under multi-point input are greater than the peak values under single point input at the same monitoring point,the peak appearing time is also earlier than that of the single point input; in terms of the plastic zone distribution,the multi-point effect is manifested as the presence of more obvious tensile shear failures; in the perspective of safety coefficient,the safety coefficient under each multi-point input is smaller than that of single point input,a difference of about 7 % or so. In summary,multi-point input is more reasonable and practical than single point input,so multi-point input should be considered in seismic design.
文摘There are two models in use today to analyze structural responses when subjected to earthquake ground motions, the Displacement Input Model （DIM） and the Acceleration Input Model （AIM）. The time steps used in direct integration methods for these models are analyzed to examine the suitability of DIM. Numerical results are presented and show that the time-step for DIM is about the same as for AIM, and achieves the same accuracy. This is contrary to previous research that reported that there are several sources of numerical errors associated with the direct application of earthquake displacement loading, and a very small time step is required to define the displacement record and to integrate the dynamic equilibrium equation. It is shown in this paper that DIM is as accurate and suitable as, if not more than, AIM for analyzing the response of a structure to uniformly distributed and spatially varying ground motions.
基金Natural Science Foundation of Heilongjiang Province (E0221)Commonweal Foundation of the Ministry of Science and Technology of China (2001DIB20098).
文摘Based on 266 strong ground motion records, an attenuation relationship was developed for both absolute and relative input energy spectra. The comparison of the two kinds of input energy spectra constructed from the attenuation relationship was made in this paper. The results show that there is little difference between the absolute input energy spectra and relative input energy spectra at the periods of 0.5-1.0 s for elastic systems and at the period of 0.5 s for inelastic systems. The absolute input energy spectra are much larger than relative input energy spectra in very short period range but some less than relative input energy spectra in long period range. It is also found that the ductility factor has a significant effect on both absolute and relative input energy spectra. The absolute input energy spectra increase with the increasing of ductility factor in the period range of less than 0.3 s but decrease in the period range of larger than 0.3 s. The absolute input energy spectra for different ductility factor are almost equivalent at the period about 0.3 s, but for relative input energy spectra, the period is about 0.5 s. The effect of ductility on the relative input energy spectra in the short period range is much larger than that on the absolute input energy spectra, especially on the softer site class.
