Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bott...Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.展开更多
The microstructure development of 55VNb1 microalloyed steel after warm deformation via multi-pass biaxial compression tests was studied,and the effect of thermomechanical conditions on spheroidisation of cementite lam...The microstructure development of 55VNb1 microalloyed steel after warm deformation via multi-pass biaxial compression tests was studied,and the effect of thermomechanical conditions on spheroidisation of cementite lamellae and ferrite recrystallisation for a range of deformation temperatures(600–700℃),cooling/soaking time(water quenching,air cooling,10 and 30 min of soaking time)and interpass time(0–10 s)was analysed.During deformation,the spheroidisation of pearlite is dynamically accelerated mainly by boundary splitting mechanism together with the rapid dissolution of cementite,while ferrite softening is attributed to dynamic recovery and continuous dynamic recrystallisation.The strong microstructural evolution during cooling/soaking time indicates that deformation energy accumulated is sufficient to activate metallurgical phenomena in both phases also statically.Static spheroidisation is a diffusive process,with rate controlled by the diffusion of vacancies,as suggested by the estimated activation energy.Ferrite refinement is the result of the evolution of continuous recrystallisation and pinning effect exerted by fine,globulised and homogeneously dispersed cementite particles.Increasing temperature causes accelerated kinetics in metallurgical phenomena;therefore,cooling/soaking time becomes key parameters to achieve ultrafine grained and spheroidised microstructures.Interpass time favours spheroidisation and promotes continuous recrystallisation;however,it must be carefully controlled to find a balance between recrystallisation and Ostwald ripening to optimise microstructural development.展开更多
The remodeling of macrophages mediated by biomaterials is an important step in osseointegration.The biointerfacial characteristics shaped by implants and the bioenergetic state derived from macrophages are considered ...The remodeling of macrophages mediated by biomaterials is an important step in osseointegration.The biointerfacial characteristics shaped by implants and the bioenergetic state derived from macrophages are considered the key to macrophage reprogramming.In this study,the integrated Ti/Zn composites with optimized morphology and bioactive phase were prepared by friction stir processing,which could meet the multi-biofunctional requirements in the application of narrow-diameter implants.The severe plastic deformation and the hindrance of Zn particles to grain growth promote grain refinement,resulting in enhanced mechanical properties.The cell interfacial adhesion mediated by the grain boundary collaborated the energy metabolism reprogramming induced by the released Zn ion,promoting jointly anti-inflammatory cascade in macrophages and favorable osteogenesis in bone marrow mesenchymal stem cells(BMSCs).This study provides a new simultaneous approach of morphology and composition modification for titanium implants,and reveals the important role of grain size and bioactive element in the reversion of macrophage fate as well.展开更多
Ti6Al4V alloy has been widely used in dental applications,such as orthodontic mini-implants.However,it has been reported that fluoride ions could obviously accelerate the corrosion of implant materials and affect thei...Ti6Al4V alloy has been widely used in dental applications,such as orthodontic mini-implants.However,it has been reported that fluoride ions could obviously accelerate the corrosion of implant materials and affect their performance.This work aimed to improve the F^(−)erosion resistance of Ti6Al4V alloy through the strategy of both Cu addition and grain refinement.As contrasted with Ti6Al4V alloy,both the coarse-and ultrafine-grained Ti6Al4V-5Cu alloys effectively mitigated the acceleration of the fluoride ions to the anode process,because Cu substituents blocked the continuous damage of F·_(O) doped in the passive film.Furthermore,grain refinement enhanced the protective ability of the passive film,more oxides and less adsorption amount of fluorides presented in the passive film of ultrafine-grained Ti6Al4V-5Cu alloy than those of coarse-grained Ti6Al4V-5Cu alloy.Under the combination of Cu alloying and grain refinement,the ultrafine-grained Ti6Al4V-5Cu alloy is greatly appropriate for the fabrication of orthodontic devices.展开更多
The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy(LAZ1011)with a grain size of 3.2μm,primarily composed of the BCCβphase and a small amount of the HCPαph...The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy(LAZ1011)with a grain size of 3.2μm,primarily composed of the BCCβphase and a small amount of the HCPαphase,were examined in a temperature range of 473 K to 623 K.The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling.The best superplasticity was achieved at 523 K and at strain rates of 10^(-4)-5×10^(-4)s^(-1),where tensile elongations of 550±600%were obtained.During the heating and holding stage of the tensile samples prior to tensile loading,a significant increase in grain size was observed at temperatures above 573 K.Therefore,it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms.In the investigated strain rate range,the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding,while at high strain rates,lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism.It was concluded that solute drag creep is unlikely to occur.During the late stages of deformation at 523 K,it was observed that grain boundary sliding led to the agglomeration of theαphase,resulting in significant strain hardening.Deformation mechanism maps were constructed forβ-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate,stress,temperature,and grain size,using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.展开更多
In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-...In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-Zn-Ca rods with greatly refined grains and high mechanical properties were produced.Compared to the previous as-cast microstructure,the grain size was reduced from more than 1 mm to around 4μm within 3 s by a single process cycle.The compressive yield strength was increased by 350%while the ultimate compressive strength by 53%.According to the established material flow behaviors by“tracer material”,the plastic material was transported by shear deformation.From the base material to the rod,the material experienced three stages,i.e.deformation by the tool,upward flow with additional tilt,followed by upward transportation.The microstructural evolution was revealed by“stop-action”technique.The microstructural development at regions adjacent to the rod is mainly controlled by twinning,dynamic recrystallization(DRX)as well as particle stimulated nucleation,while that within the rod is related to DRX combined with grain growth.展开更多
Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using sc...Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using scanning electron microscopy(SEM), energy dispersive X-ray analysis(EDS), X-ray diffractometry(XRD) and mechanical properties tests. The results show that the maximum values of hardness and strength are HV 1124 and 2466 MPa respectively when 0.4% TaC is added. When the content of TaC is more than 0.6%, the grain size of WC is no longer affected by the amount of TaC, and(W,Ta)C occurs as well. Moreover, the strength and fracture toughness increase and the(Ta+W) content decreases with the increase of TaC content. The dependence of(Ta+W) content on the mechanical properties indicates that(Ta+W) content in Co should be decreased as low as possible to improve the mechanical properties of coarse grained WC-TaC-9Co cemented carbides with the microstructure of WC+γ two phase regions.展开更多
Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of ...Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.展开更多
Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of...Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.展开更多
Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures ...Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures and mechanical properties of the joints were investigated. A sound bead, with the ultimate tensile strength （UTS） of 300 MPa and elongation of 12.0%, up to 92.5% and 65% of those of the base metal, respectively, is obtained with the optimized welding parameters. No liquation cracking is visible in the partially melted zone （PMZ） owing to the inhibitory action of the fine dispersed precipitates and the fine-grained microstructure in the as-rolled magnesium alloy sheets. The fusion zone （FZ） is featured with the equiaxed dendritic grains of the average grain size about 8 μm, which are similar to those in the heat affected zone （HAZ）, and this contributes to the relatively high joint efficiency.展开更多
3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is l...3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.展开更多
In order to analyze the effect of grain size on stress relaxation(SR) mechanism,the SR tests of TC4 alloy with three kinds of grain size were performed in a temperature range of 650-750℃.A modified cubic delay functi...In order to analyze the effect of grain size on stress relaxation(SR) mechanism,the SR tests of TC4 alloy with three kinds of grain size were performed in a temperature range of 650-750℃.A modified cubic delay function was used to establish SR model for each grain size.A simplified algorithm was proposed for calculating the deformation activation energy based on classical Arrhenius equation.The grain size distribution and variation were observed by microstructural methods.The experimental results indicate that smaller grains are earlier to reach the relaxation limit at the same temperature due to lower initial stress and faster relaxation rate.The SR limit at 650℃ reduces with decreasing grain size.While the effect of grain size on SR limit is not evident at 700 and 750℃ since the relaxation is fully completed.With the increase of grain size,the deformation activation energy is improved and SR mechanism at 700℃ changes from grain rotation and grain boundary sliding to dislocation movement and dynamic recovery.展开更多
The microstructural evolutions of the cold rolled Fe-0.1C-5Mn steel during intercritical annealing were ex- amined using combined advanced techniques. It was demonstrated that intercritical annealing results in an ult...The microstructural evolutions of the cold rolled Fe-0.1C-5Mn steel during intercritical annealing were ex- amined using combined advanced techniques. It was demonstrated that intercritical annealing results in an ultrafine granular ferrite and austenite duplex structure in cold rolled 0.1C-5Mn steel. The strong partitioning of manganese and carbon elements from ferrite to austenite was found during intercritical annealing by scanning transmission elec- tron microscopy （STEM） and X-ray diffraction （XRD）. Strong effects of boundary characters on the austenite for- mation were indicated by austenite fast nucleation and growth in the high angle boundaries but sluggish nucleation and growth in the low angle boundaries. The ultrafine grained duplex structure in 0.1C-5Mn was resulted from the the sluggish Mn-diffusion and the extra high Gibbs free energy of ferrite phase. Based on the analysis of the micro- structure evolution, it was pointed out that the intercritical annealing of the medium Mn steels could be applied to fabricate an ultrafine duplex grained microstructure, which would be a promising approach to develop the 3rd genera- tion austomobile steels with excellent combination of strength and ductility.展开更多
Ultrafine grained AA6063-SiCnpnanocomposites with 1, 5 and 10 vol.% SiCnphave been fabricated by a novel powder metallurgy process. This process combines high energy ball milling of a mixture of 6063 alloy granules ma...Ultrafine grained AA6063-SiCnpnanocomposites with 1, 5 and 10 vol.% SiCnphave been fabricated by a novel powder metallurgy process. This process combines high energy ball milling of a mixture of 6063 alloy granules made from machining chips and Si C nanoparticles and thermomechanical powder consolidation by spark plasma sintering and hot extrusion. The microstructure and tensile mechanical properties of the samples were investigated in detail. Increasing the Si C nanoparticle content from 1 to 10 vol.%,the yield strength and ultimate tensile strength increased from 296 and 343 MPa to 545 and 603 MPa respectively, and the elongation to fracture decreased from 10.0%, to 2.3%. As expected, a higher Si C nanoparticle content generates a stronger inhibiting effect to grain growth during the thermomechanical powder consolidation process. Analysis of the contributions of various strengthening mechanisms shows that a higher Si C nanoparticle content leads to a higher contribution from nanoparticle strengthening, but grain boundary strengthening still makes the largest contribution to the strength of the nanocomposite.When the Si C nanoparticle content increased to 10 vol.%, the failure of the nanocomposite was initiated at weakly-bonded interparticle boundaries(IPBs), indicating that with a high flow stress during tensile deformation, the failure of the material is more sensitive to the presence of weakly-bonded IPBs.展开更多
The effect of phosphorus on mechanical properties and thermal stability of fine-grained GH761 alloy has been investigated.The results show that,when the content of phosphorus is in the range of 0.0007-0.040,there are ...The effect of phosphorus on mechanical properties and thermal stability of fine-grained GH761 alloy has been investigated.The results show that,when the content of phosphorus is in the range of 0.0007-0.040,there are no significant effects on the tensile properties.Phosphorus strongly affects the stress rupture life.The content of 0.023 P results in the longest life in this experiment.Compared with that of the alloy with 0.0007 P,the life is increased more than 2 times in the alloy with 0.023 P.After ageing at 700℃ for 1000 h,the life reduced to some extent.However,phosphorus exhibits the similar effect on the life as before ageing.The tensile properties of the alloy are not influenced by long term ageing obviously.The present results suggested that the optimum content of phosphorus is 0.023.The phosphorus with this content can optimize the precipitates at the grain boundaries and prevent the excessive growth of the precipitates.The combining mechanical properties of GH761 alloy can be largely improved by phosphorus addition combined with grain refinement.展开更多
Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to ...Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to reveal different deformation mechanisms and to compare with those of coarse grained samples. Dominant double-prismatic slip, {1012} twinning and basal slip are detected in three types of samples, respectively, which is similar to those of coarse grained samples. The detrimental effect of shear band formation or {1011} twinning is limited in fine grained microstructure. In addition to the higher flow stress at low temperature an early decrease in flow stress at higher temperature is also found in fine-grained samples in comparison with their coarse-grained counterparts. This softening is ascribed to the early dynamic recrystallization or grain boundary glide.展开更多
Dynamic compression tests were carried out to investigate dynamic mechanical behavior and adiabatic shear bands in ultrafine grained(UFG)pure zirconium prepared by equal channel angular pressing(ECAP)and rotary swayin...Dynamic compression tests were carried out to investigate dynamic mechanical behavior and adiabatic shear bands in ultrafine grained(UFG)pure zirconium prepared by equal channel angular pressing(ECAP)and rotary swaying.The cylindrical specimens were deformed dynamically on the split Hopkinson pressure bar(SHPB)at different strain rates of 800 to 4000s^-1 at room temperature.The temperature distribution of the shear bands was estimated on the basis of temperature rise of uniform plastic deformation stage and thermal diffusion effect.The results show that the true stress-true strain curves of UFG pure zirconium are concave upward trend of strain in range of 0.02-0.16 due to the effects of strain hardening,strain rate hardening and thermal softening.The formation of the adiabatic shear bands is the main reason of UFG pure zirconium failure.A large number of micro-voids are observed in the adiabatic shear bands,and the macroscopic cracks develop from the micro-voids coalescence.The fracture surface of UFG pure zirconium exhibits quasi cleavage fracture with the characteristic features of shear dimples and river pattern.The highest temperature within the shear bands of UFG pure zirconium is about 592 K.展开更多
2017 aluminum alloy plates with an ultrafine grained （UFG） structure were produced by equal channel angular processing （ECAP） and then were joined by underwater friction stir welding （underwater FSW）. X-ray diff...2017 aluminum alloy plates with an ultrafine grained （UFG） structure were produced by equal channel angular processing （ECAP） and then were joined by underwater friction stir welding （underwater FSW）. X-ray diffractometer （XRD）, transmission electron microscope （TEM）, scanning electron microscope （SEM） and microhardness tester were adopted to investigate the microstructural and mechanical characteristics of the FSW joint. The results indicate that an ultrafine grained microstructure with the mean grain size of-0.7 Ixm is obtained in the weld nugget by using water cooling. However, The FSW joint exhibits softening compared with the ultrafine grained based material and the heat affected zone （HAZ） has the lowest hardness owing to the coarsening of the strengthening precipitates.展开更多
Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading...Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading.In this paper,repeated load triaxial tests were performed on coarse-grained soil(CGS),and the axial permanent strain of CGS under different confining pressures and dynamic stress amplitudes was analysed.Permanent deformation behaviors of CGS were categorized based on the variation trend of permanent strain rate with accumulated permanent strain and the shakedown theory.A prediction model of permanent deformation considering stress state and number of load cycles was established,and the ranges of parameters for different types of dynamic behaviors were also divided.The results indicated that the variational trend of permanent strain rate with accumulated permanent strain can be used as a basis for classifying dynamic behaviors of CGS.The stress state(confining pressure and dynamic stress amplitude)has significant effects on the permanent strain rate.The accumulative characteristics of permanent deformation of CGS with the number of load cycles can be described by a power function,and the model parameters can reflect the influence of confining pressure and dynamic stress amplitude.The study’s results could help deepen understanding of the permanent deformation characteristics of CGS.展开更多
In debris flow modelling,the viscosity and yield stress of fine-grained sediments should be determined in order to better characterize sediment flow.In particular,it is important to understand the effect of grain size...In debris flow modelling,the viscosity and yield stress of fine-grained sediments should be determined in order to better characterize sediment flow.In particular,it is important to understand the effect of grain size on the rheology of fine-grained sediments associated with yielding.When looking at the relationship between shear stress and shear rate before yielding,a high-viscosity zone(called pseudoNewtonian viscosity) towards the apparent yield stress exists.After yielding,plastic viscosity(called Bingham viscosity) governs the flow.To examine the effect of grain size on the rheological characteristics of fine-grained sediments,clay-rich materials(from the Adriatic Sea,Italy; Cambridge Fjord,Canada; and the Mediterranean Sea,Spain),silt-rich debris flow materials(from La Valette,France) and silt-rich materials(iron tailings from Canada) were compared.Rheological characteristics were examined using a modified Bingham model.The materials examined,including the Canadian inorganic and sensitive clays,exhibit typical shear thinning behavior and strong thixotropy.In the relationships between the liquidity index and rheological values(viscosity and apparent yield stress),the effect of grain size on viscosity and yield stress is significant at a given liquidity index.The viscosity and yield stress of debris flow materials are higher than those of low-activity clays at the same liquid state.However the viscosity and yield stress of the tailings,which are mainly composed of silt-sized particles,are slightly lower than those of low-activity clays.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52371128,52304378,52101031 and 92163107).
文摘Grain boundary engineering plays a significant role in the improvement of strength and plasticity of alloys. However, in refractory high-entropy alloys, the susceptibility of grain boundaries to oxygen presents a bottleneck in achieving high mechanical performance. Creating a large number of clean grain boundaries in refractory high-entropy alloys is a challenge. In this study, an ultrafine-grained (UFG) NbMoTaW alloy with high grain-boundary cohesion was prepared by powder metallurgy, taking advantages of rapid hot-pressing sintering and full-process inert atmosphere protection from powder synthesis to sintering. By oxygen control and an increase in the proportion of grain boundaries, the segregation of oxygen and formation of oxides at grain boundaries were strongly mitigated, thus the intrinsic high cohesion of the interfaces was preserved. Compared to the coarse-grained alloys prepared by arc-melting and those sintered by traditional powder metallurgy methods, the UFG NbMoTaW alloy demonstrated simultaneously increased strength and plasticity at ambient temperature. The highly cohesive grain boundaries not only reduce brittle fractures effectively but also promote intragranular deformation. Consequently, the UFG NbMoTaW alloy achieved a high yield strength even at elevated temperatures, with a remarkable performance of 1117 MPa at 1200 ℃. This work provides a feasible solution for producing refractory high-entropy alloys with low impurity content, refined microstructure, and excellent mechanical performance.
基金financially supported by the European Coal and Steel Community(RFCS-2015.No.709828).
文摘The microstructure development of 55VNb1 microalloyed steel after warm deformation via multi-pass biaxial compression tests was studied,and the effect of thermomechanical conditions on spheroidisation of cementite lamellae and ferrite recrystallisation for a range of deformation temperatures(600–700℃),cooling/soaking time(water quenching,air cooling,10 and 30 min of soaking time)and interpass time(0–10 s)was analysed.During deformation,the spheroidisation of pearlite is dynamically accelerated mainly by boundary splitting mechanism together with the rapid dissolution of cementite,while ferrite softening is attributed to dynamic recovery and continuous dynamic recrystallisation.The strong microstructural evolution during cooling/soaking time indicates that deformation energy accumulated is sufficient to activate metallurgical phenomena in both phases also statically.Static spheroidisation is a diffusive process,with rate controlled by the diffusion of vacancies,as suggested by the estimated activation energy.Ferrite refinement is the result of the evolution of continuous recrystallisation and pinning effect exerted by fine,globulised and homogeneously dispersed cementite particles.Increasing temperature causes accelerated kinetics in metallurgical phenomena;therefore,cooling/soaking time becomes key parameters to achieve ultrafine grained and spheroidised microstructures.Interpass time favours spheroidisation and promotes continuous recrystallisation;however,it must be carefully controlled to find a balance between recrystallisation and Ostwald ripening to optimise microstructural development.
基金the National Natural Science Foundation of China(Nos.31971246&52274387)the Fundamental Research Funds for the Central Universities(No.YG2023QNA21)the Shanghai Science and Technology Commission(No.20S31900100)for their financial and project support.
文摘The remodeling of macrophages mediated by biomaterials is an important step in osseointegration.The biointerfacial characteristics shaped by implants and the bioenergetic state derived from macrophages are considered the key to macrophage reprogramming.In this study,the integrated Ti/Zn composites with optimized morphology and bioactive phase were prepared by friction stir processing,which could meet the multi-biofunctional requirements in the application of narrow-diameter implants.The severe plastic deformation and the hindrance of Zn particles to grain growth promote grain refinement,resulting in enhanced mechanical properties.The cell interfacial adhesion mediated by the grain boundary collaborated the energy metabolism reprogramming induced by the released Zn ion,promoting jointly anti-inflammatory cascade in macrophages and favorable osteogenesis in bone marrow mesenchymal stem cells(BMSCs).This study provides a new simultaneous approach of morphology and composition modification for titanium implants,and reveals the important role of grain size and bioactive element in the reversion of macrophage fate as well.
基金supported by the Liaoning Provincial Science and Technology Program-Excellent Youth Fund Program(2023JH3/10200002)National Key Research and Development Program of China(2022YFC2406000)+1 种基金National Natural Science Foundation of China(52301308)IMR Innovation fund(2023-PY15).
文摘Ti6Al4V alloy has been widely used in dental applications,such as orthodontic mini-implants.However,it has been reported that fluoride ions could obviously accelerate the corrosion of implant materials and affect their performance.This work aimed to improve the F^(−)erosion resistance of Ti6Al4V alloy through the strategy of both Cu addition and grain refinement.As contrasted with Ti6Al4V alloy,both the coarse-and ultrafine-grained Ti6Al4V-5Cu alloys effectively mitigated the acceleration of the fluoride ions to the anode process,because Cu substituents blocked the continuous damage of F·_(O) doped in the passive film.Furthermore,grain refinement enhanced the protective ability of the passive film,more oxides and less adsorption amount of fluorides presented in the passive film of ultrafine-grained Ti6Al4V-5Cu alloy than those of coarse-grained Ti6Al4V-5Cu alloy.Under the combination of Cu alloying and grain refinement,the ultrafine-grained Ti6Al4V-5Cu alloy is greatly appropriate for the fabrication of orthodontic devices.
文摘The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy(LAZ1011)with a grain size of 3.2μm,primarily composed of the BCCβphase and a small amount of the HCPαphase,were examined in a temperature range of 473 K to 623 K.The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling.The best superplasticity was achieved at 523 K and at strain rates of 10^(-4)-5×10^(-4)s^(-1),where tensile elongations of 550±600%were obtained.During the heating and holding stage of the tensile samples prior to tensile loading,a significant increase in grain size was observed at temperatures above 573 K.Therefore,it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms.In the investigated strain rate range,the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding,while at high strain rates,lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism.It was concluded that solute drag creep is unlikely to occur.During the late stages of deformation at 523 K,it was observed that grain boundary sliding led to the agglomeration of theαphase,resulting in significant strain hardening.Deformation mechanism maps were constructed forβ-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate,stress,temperature,and grain size,using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.
基金the China Scholarship Council for the award of fellowship and funding(No.202006230137)。
文摘In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-Zn-Ca rods with greatly refined grains and high mechanical properties were produced.Compared to the previous as-cast microstructure,the grain size was reduced from more than 1 mm to around 4μm within 3 s by a single process cycle.The compressive yield strength was increased by 350%while the ultimate compressive strength by 53%.According to the established material flow behaviors by“tracer material”,the plastic material was transported by shear deformation.From the base material to the rod,the material experienced three stages,i.e.deformation by the tool,upward flow with additional tilt,followed by upward transportation.The microstructural evolution was revealed by“stop-action”technique.The microstructural development at regions adjacent to the rod is mainly controlled by twinning,dynamic recrystallization(DRX)as well as particle stimulated nucleation,while that within the rod is related to DRX combined with grain growth.
基金Project(2013zzts025)supported by the Fundamental Research Funds for the Central Universities of China
文摘Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using scanning electron microscopy(SEM), energy dispersive X-ray analysis(EDS), X-ray diffractometry(XRD) and mechanical properties tests. The results show that the maximum values of hardness and strength are HV 1124 and 2466 MPa respectively when 0.4% TaC is added. When the content of TaC is more than 0.6%, the grain size of WC is no longer affected by the amount of TaC, and(W,Ta)C occurs as well. Moreover, the strength and fracture toughness increase and the(Ta+W) content decreases with the increase of TaC content. The dependence of(Ta+W) content on the mechanical properties indicates that(Ta+W) content in Co should be decreased as low as possible to improve the mechanical properties of coarse grained WC-TaC-9Co cemented carbides with the microstructure of WC+γ two phase regions.
基金Project(2014CB644003)supported by the National Basic Research Program of ChinaProject(51321003)supported by the National Natural Science Foundation of ChinaProject(B06025)supported by"111"Project of China
文摘Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.
基金roject (50634060) supported by the National Natural Science Foundation of ChinaProject (2010GB109000) supported by the National Basic Research Program of China
文摘Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.
基金Project(51274092)supported by the National Natural Science Foundation of ChinaProject(20120161110040)supported by the Doctoral Program of Higher Education of China
文摘Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures and mechanical properties of the joints were investigated. A sound bead, with the ultimate tensile strength （UTS） of 300 MPa and elongation of 12.0%, up to 92.5% and 65% of those of the base metal, respectively, is obtained with the optimized welding parameters. No liquation cracking is visible in the partially melted zone （PMZ） owing to the inhibitory action of the fine dispersed precipitates and the fine-grained microstructure in the as-rolled magnesium alloy sheets. The fusion zone （FZ） is featured with the equiaxed dendritic grains of the average grain size about 8 μm, which are similar to those in the heat affected zone （HAZ）, and this contributes to the relatively high joint efficiency.
基金This work was supported by the‘973'ScienceTechnology Development Plan of the National Basic Research Foundation(No.1998061500)the 985'Foundation of Tsinghua University.
文摘3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.
基金Projects(2016ZE57008,20163657004)supported by Aeronautical Science Foundation of ChinaProject(USCAST2016-20)supported by the SAST-SJTU Joint Research Centre of Advanced Aerospace Technology,ChinaProject(51875350)supported by the National Natural Science Foundation of China
文摘In order to analyze the effect of grain size on stress relaxation(SR) mechanism,the SR tests of TC4 alloy with three kinds of grain size were performed in a temperature range of 650-750℃.A modified cubic delay function was used to establish SR model for each grain size.A simplified algorithm was proposed for calculating the deformation activation energy based on classical Arrhenius equation.The grain size distribution and variation were observed by microstructural methods.The experimental results indicate that smaller grains are earlier to reach the relaxation limit at the same temperature due to lower initial stress and faster relaxation rate.The SR limit at 650℃ reduces with decreasing grain size.While the effect of grain size on SR limit is not evident at 700 and 750℃ since the relaxation is fully completed.With the increase of grain size,the deformation activation energy is improved and SR mechanism at 700℃ changes from grain rotation and grain boundary sliding to dislocation movement and dynamic recovery.
基金Item Sponsored by National Natural Science Foundation of China(51371057)National Basic Research Program of China(2010CB630803)
文摘The microstructural evolutions of the cold rolled Fe-0.1C-5Mn steel during intercritical annealing were ex- amined using combined advanced techniques. It was demonstrated that intercritical annealing results in an ultrafine granular ferrite and austenite duplex structure in cold rolled 0.1C-5Mn steel. The strong partitioning of manganese and carbon elements from ferrite to austenite was found during intercritical annealing by scanning transmission elec- tron microscopy （STEM） and X-ray diffraction （XRD）. Strong effects of boundary characters on the austenite for- mation were indicated by austenite fast nucleation and growth in the high angle boundaries but sluggish nucleation and growth in the low angle boundaries. The ultrafine grained duplex structure in 0.1C-5Mn was resulted from the the sluggish Mn-diffusion and the extra high Gibbs free energy of ferrite phase. Based on the analysis of the micro- structure evolution, it was pointed out that the intercritical annealing of the medium Mn steels could be applied to fabricate an ultrafine duplex grained microstructure, which would be a promising approach to develop the 3rd genera- tion austomobile steels with excellent combination of strength and ductility.
基金supported by the National Natural Science Foundation of China (No. 51271115)SJTU-UNSW Collaborative Research & Development Fund
文摘Ultrafine grained AA6063-SiCnpnanocomposites with 1, 5 and 10 vol.% SiCnphave been fabricated by a novel powder metallurgy process. This process combines high energy ball milling of a mixture of 6063 alloy granules made from machining chips and Si C nanoparticles and thermomechanical powder consolidation by spark plasma sintering and hot extrusion. The microstructure and tensile mechanical properties of the samples were investigated in detail. Increasing the Si C nanoparticle content from 1 to 10 vol.%,the yield strength and ultimate tensile strength increased from 296 and 343 MPa to 545 and 603 MPa respectively, and the elongation to fracture decreased from 10.0%, to 2.3%. As expected, a higher Si C nanoparticle content generates a stronger inhibiting effect to grain growth during the thermomechanical powder consolidation process. Analysis of the contributions of various strengthening mechanisms shows that a higher Si C nanoparticle content leads to a higher contribution from nanoparticle strengthening, but grain boundary strengthening still makes the largest contribution to the strength of the nanocomposite.When the Si C nanoparticle content increased to 10 vol.%, the failure of the nanocomposite was initiated at weakly-bonded interparticle boundaries(IPBs), indicating that with a high flow stress during tensile deformation, the failure of the material is more sensitive to the presence of weakly-bonded IPBs.
基金supported by the National Natural Science Foundation of China under the contracts of Nos.50271072 & 50471083
文摘The effect of phosphorus on mechanical properties and thermal stability of fine-grained GH761 alloy has been investigated.The results show that,when the content of phosphorus is in the range of 0.0007-0.040,there are no significant effects on the tensile properties.Phosphorus strongly affects the stress rupture life.The content of 0.023 P results in the longest life in this experiment.Compared with that of the alloy with 0.0007 P,the life is increased more than 2 times in the alloy with 0.023 P.After ageing at 700℃ for 1000 h,the life reduced to some extent.However,phosphorus exhibits the similar effect on the life as before ageing.The tensile properties of the alloy are not influenced by long term ageing obviously.The present results suggested that the optimum content of phosphorus is 0.023.The phosphorus with this content can optimize the precipitates at the grain boundaries and prevent the excessive growth of the precipitates.The combining mechanical properties of GH761 alloy can be largely improved by phosphorus addition combined with grain refinement.
基金This work was supported by the National Natural Sci-ence Foundation of China under grant No.50171009the National 863 Program of China(No.2002A A305501)Part work was performed at IMM RWTH A achen,Germany.
文摘Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to reveal different deformation mechanisms and to compare with those of coarse grained samples. Dominant double-prismatic slip, {1012} twinning and basal slip are detected in three types of samples, respectively, which is similar to those of coarse grained samples. The detrimental effect of shear band formation or {1011} twinning is limited in fine grained microstructure. In addition to the higher flow stress at low temperature an early decrease in flow stress at higher temperature is also found in fine-grained samples in comparison with their coarse-grained counterparts. This softening is ascribed to the early dynamic recrystallization or grain boundary glide.
基金Funded by National Natural Science Foundation of China(No.51474170)Natural Science Foundation of Shaanxi Province(No.2016JQ5026)Foundation of Liaoning Province Educational Committee(No.2017LNQN14).
文摘Dynamic compression tests were carried out to investigate dynamic mechanical behavior and adiabatic shear bands in ultrafine grained(UFG)pure zirconium prepared by equal channel angular pressing(ECAP)and rotary swaying.The cylindrical specimens were deformed dynamically on the split Hopkinson pressure bar(SHPB)at different strain rates of 800 to 4000s^-1 at room temperature.The temperature distribution of the shear bands was estimated on the basis of temperature rise of uniform plastic deformation stage and thermal diffusion effect.The results show that the true stress-true strain curves of UFG pure zirconium are concave upward trend of strain in range of 0.02-0.16 due to the effects of strain hardening,strain rate hardening and thermal softening.The formation of the adiabatic shear bands is the main reason of UFG pure zirconium failure.A large number of micro-voids are observed in the adiabatic shear bands,and the macroscopic cracks develop from the micro-voids coalescence.The fracture surface of UFG pure zirconium exhibits quasi cleavage fracture with the characteristic features of shear dimples and river pattern.The highest temperature within the shear bands of UFG pure zirconium is about 592 K.
基金Projects(50774059, 51074119) supported by the National Natural Science Foundation of China
文摘2017 aluminum alloy plates with an ultrafine grained （UFG） structure were produced by equal channel angular processing （ECAP） and then were joined by underwater friction stir welding （underwater FSW）. X-ray diffractometer （XRD）, transmission electron microscope （TEM）, scanning electron microscope （SEM） and microhardness tester were adopted to investigate the microstructural and mechanical characteristics of the FSW joint. The results indicate that an ultrafine grained microstructure with the mean grain size of-0.7 Ixm is obtained in the weld nugget by using water cooling. However, The FSW joint exhibits softening compared with the ultrafine grained based material and the heat affected zone （HAZ） has the lowest hardness owing to the coarsening of the strengthening precipitates.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.51878666 and 51678572).
文摘Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading.In this paper,repeated load triaxial tests were performed on coarse-grained soil(CGS),and the axial permanent strain of CGS under different confining pressures and dynamic stress amplitudes was analysed.Permanent deformation behaviors of CGS were categorized based on the variation trend of permanent strain rate with accumulated permanent strain and the shakedown theory.A prediction model of permanent deformation considering stress state and number of load cycles was established,and the ranges of parameters for different types of dynamic behaviors were also divided.The results indicated that the variational trend of permanent strain rate with accumulated permanent strain can be used as a basis for classifying dynamic behaviors of CGS.The stress state(confining pressure and dynamic stress amplitude)has significant effects on the permanent strain rate.The accumulative characteristics of permanent deformation of CGS with the number of load cycles can be described by a power function,and the model parameters can reflect the influence of confining pressure and dynamic stress amplitude.The study’s results could help deepen understanding of the permanent deformation characteristics of CGS.
基金funded by the Natural Sciences and Engineering Research Council,Canada,via the COSTA(Continental Slope Stability)-Canada projectsupported by the Public Welfare & Safety Research Program through the National Research Foundation of Korea(NRF)+1 种基金funded by the Ministry of Science,ICT&Future Planning(Grant No.2012M3A2A1050983)the Research Project (11-7622,13-3212)of the Korea Institute of Geoscience and Mineral Resources(KIGAM)
文摘In debris flow modelling,the viscosity and yield stress of fine-grained sediments should be determined in order to better characterize sediment flow.In particular,it is important to understand the effect of grain size on the rheology of fine-grained sediments associated with yielding.When looking at the relationship between shear stress and shear rate before yielding,a high-viscosity zone(called pseudoNewtonian viscosity) towards the apparent yield stress exists.After yielding,plastic viscosity(called Bingham viscosity) governs the flow.To examine the effect of grain size on the rheological characteristics of fine-grained sediments,clay-rich materials(from the Adriatic Sea,Italy; Cambridge Fjord,Canada; and the Mediterranean Sea,Spain),silt-rich debris flow materials(from La Valette,France) and silt-rich materials(iron tailings from Canada) were compared.Rheological characteristics were examined using a modified Bingham model.The materials examined,including the Canadian inorganic and sensitive clays,exhibit typical shear thinning behavior and strong thixotropy.In the relationships between the liquidity index and rheological values(viscosity and apparent yield stress),the effect of grain size on viscosity and yield stress is significant at a given liquidity index.The viscosity and yield stress of debris flow materials are higher than those of low-activity clays at the same liquid state.However the viscosity and yield stress of the tailings,which are mainly composed of silt-sized particles,are slightly lower than those of low-activity clays.
