Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to ...Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to reveal different deformation mechanisms and to compare with those of coarse grained samples. Dominant double-prismatic slip, {1012} twinning and basal slip are detected in three types of samples, respectively, which is similar to those of coarse grained samples. The detrimental effect of shear band formation or {1011} twinning is limited in fine grained microstructure. In addition to the higher flow stress at low temperature an early decrease in flow stress at higher temperature is also found in fine-grained samples in comparison with their coarse-grained counterparts. This softening is ascribed to the early dynamic recrystallization or grain boundary glide.展开更多
An as-cast magnesium alloy with high Al content Mg15Al was subjected to equal-channel angular pressing （ECAP） through a die with an angle of φ= 90？ at 553 K following route Bc. It is found that the network β-Mg17...An as-cast magnesium alloy with high Al content Mg15Al was subjected to equal-channel angular pressing （ECAP） through a die with an angle of φ= 90？ at 553 K following route Bc. It is found that the network β-Mg17Al12 phases in the as-cast Mg15Al alloy are broken into small blocks and dispersed uniformly with increasing numbers of pressing passes. Moreover, many nano-sized Mg17Al12 particles precipitate in the ultra-fine α-Mg matrix. The grains are obviously refined. However, the grain structure is inhomogeneous in different areas of the alloy. The average size of the primary phase α-Mg is reduced to about 1 μm while grains of around 0.1-0.2 μm are obtained in some two-phase areas. With additional ECAP passes （up to 8）, coarsening of the grains occurs by dynamic recovery. Room temperature tensile tests show that the mechanical properties of Mg15Al alloys are markedly improved after 4 ECAP passes. The ultimate tensile strength and elongation to failure increase from 150 MPa to 269.3 MPa and from 0.05% to 7.4%, respectively. Compared with that after 4 passes, the elongation to failure of the alloy increases but the strength of the alloy slightly decreases after 8 ECAP passes. Fracture morphology of the ECAP-processed alloy exhibits dimple-like fracture characteristics while the as-cast alloy shows quasi-cleavage fractures.展开更多
An ultrafine grained microstructure was obtained for 304 stainless steel(304SS)sheets by using surface nanocrystallization and warm-rolling.The microstructure and mechanical properties were determined by X-ray diffrac...An ultrafine grained microstructure was obtained for 304 stainless steel(304SS)sheets by using surface nanocrystallization and warm-rolling.The microstructure and mechanical properties were determined by X-ray diffraction(XRD),transmission electron microscope(TEM)and a test on microhardness.Experimental results were shown that the microstructure was featured by a continuous distribution from the nanocrystalline on the surface to micro-grains in the center,in which the volume fraction of the micro-sized grains is about 40% in the surface layer.This multi-scale grained microstructure was composed of austenite and martensite phases with a gradient increasing volume fraction of austenite from the surface to the centre.The microhardness of the resultant steel was higher than 150% of that as received,due to the refined grains and strain-induced martensitic transformation.The hardness distribution was consistent with the microstructural variation,suggesting a good combination of high strength and improved ductility.展开更多
In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction he...In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.展开更多
Through molecular dynamics（MD） simulation, the dependencies of temperature, grain size and strain rate on the mechanical properties were studied. The simulation results demonstrated that the strain rate from 0.05 to...Through molecular dynamics（MD） simulation, the dependencies of temperature, grain size and strain rate on the mechanical properties were studied. The simulation results demonstrated that the strain rate from 0.05 to 2 ns–1 affected the Young＇s modulus of nickel nanowires slightly, whereas the yield stress increased. The Young＇s modulus decreased approximately linearly; however, the yield stress firstly increased and subsequently dropped as the temperature increased. The Young＇s modulus and yield stress increased as the mean grain size increased from 2.66 to 6.72 nm. Moreover, certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension. Certain phenomena such as the formation of twin structures, which were found in nanowires with larger grain size at higher strain rate and lower temperature, as well as the movement of grain boundaries and dislocation, were detected and discussed in detail. The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size. However, for larger grain size, the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.展开更多
The uniform refinement mechanisms and methods of deformed mixed and coarse grains inside a solution-treatment Ni-based superalloy during two-stage annealing treatment have been investigated.The two-stage heat treatmen...The uniform refinement mechanisms and methods of deformed mixed and coarse grains inside a solution-treatment Ni-based superalloy during two-stage annealing treatment have been investigated.The two-stage heat treatment experiments include an aging annealing treatment(AT)and a subsequent recrystallization annealing treatment(RT).The object of AT is to precipitate someδphases and consume part of storage energy to inhibit the grain growth during RT,while the RT is to refine mixed and coarse grains by recrystallization.It can be found that the recrystallization grains will quickly grow up to a large size when the AT time is too low or the RT temperature is too high,while the deformed coarse grains cannot be eliminated when the AT time is too long or the RT temperature is too low.In addition,the mixed microstructure composed of some abnormal coarse recrystallization grains(ACRGs)and a large number of fine grains can be observed in the annealed specimen when the AT time is 3 h and RT temperature is 980℃.The phenomenon attributes to the uneven distribution ofδphase resulted from the heterogeneous deformation energy when the AT time is too short.In the regions with a large number ofδphases,the recrystallization nucleation rate is promoted and the growth of grains is limited,which results in fine grains.However,in the regions with fewδphases,the recrystallization grains around grain boundaries can easily grow up,and the new recrystallization nucleus is difficult to form inside grain,which leads to ACRGs.Thus,in order to obtain uniform and fine annealed microstructure,it is a prerequisite to precipitate even-distributedδphase by choosing a suitable AT time,such as 12 h.Moreover,a relative high RT temperature is also needed to promote the recrystallization nucleation aroundδphase.The optimal annealing parameters range for uniformly refining mixed crystal can be summarized as:900℃×12 h+990℃×(40-60 min)and 900℃×12 h+1000℃×(10-15 min).展开更多
Cu-4.7%Sn （mass fraction） alloy plate was prepared by the self-developed two-phase zone continuous casting （TZCC） process. The relationship between process parameters of TZCC and surface quality of the alloy plate...Cu-4.7%Sn （mass fraction） alloy plate was prepared by the self-developed two-phase zone continuous casting （TZCC） process. The relationship between process parameters of TZCC and surface quality of the alloy plate was investigated. The microstructure and mechanical properties of the TZCC alloy plate were analyzed. The results show that Cu-4.7%Sn alloy plate with smooth surface can be obtained by means of reasonable matching the entrance temperature of two-phase zone mold and the continuous casting speed. The microstructure of the TZCC alloy is composed of grains-covered grains, small grains with self-closed grain boundaries, columnar grains and equiaxed grains. Compared with cold mold continuous casting Cu-4.7%Sn alloy plate, the room temperature tensile strength and ductility of the TZCC alloy plate are greatly improved.展开更多
Friction stir processing （FSP）, a variation of FSW （friction stir welding） is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the...Friction stir processing （FSP）, a variation of FSW （friction stir welding） is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the mechanical properties of material. FSP can also produce fine grained microstructures through the thickness to impart superplasticity. The technology involves plunging a rapidly rotating, non consumable tool, comprising a profiled pin and larger diameter shoulder, into the surface and then traversing the tool across the surface. The pin and the shoulder friction heat the surface which alters the grain structure in the processed area thereby improving the mechanical properties. This paper presents the effects of FSP on microstructure and mechanical properties of extruded cast 2285 aluminum alloy at three different feed rates viz. 10, 12 and 15 mm/min. With the increase in the feed speed the material was observed to have increased impact strength. FSP also increased the tensile and yield strengths with increases in hardness and ductility values also. The observation has been listed in detail and pictorially represented.展开更多
The effects of milling parameters on the surface quality,microstructures and mechanical properties of machined parts with ultrafine grained(UFG)gradient microstructures are investigated.The effects of the cutting spee...The effects of milling parameters on the surface quality,microstructures and mechanical properties of machined parts with ultrafine grained(UFG)gradient microstructures are investigated.The effects of the cutting speed,feed per tooth,cutting tool geometry and cooling strategy are demonstrated.It has been found that the surface quality of machined grooves can be improved by increasing the cutting speed.However,cryogenic cooling with CO_2 exhibits no significant improvement of surface quality.Microstructure and hardness investigations revealed similar microstructure and hardness variations near the machined groove walls for both utilized tool geometries.Therefore,cryogenic cooling can decrease more far-ranging hardness reductions due to high process temperatures,especially in the UFG regions of the machined parts,whilst it cannot prevent the drop in hardness directly at the groove walls.展开更多
Effects of Nd on microstructure and mechanical properties of as-cast Mg-8Li-3Al alloy were investigated by OM,X-ray diffraction（XRD）,EPMA,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS）...Effects of Nd on microstructure and mechanical properties of as-cast Mg-8Li-3Al alloy were investigated by OM,X-ray diffraction（XRD）,EPMA,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS）.The results showed that the dendrites sizes of α phase were decreased by the Nd addition.When the amount of addition Nd was 1.6 wt.%,the alloy with the smallest α phase was obtained.The refining mechanism mainly owed to the increasing constitutional supercooling at the solidification front.Furthermore,the compound Al 2 Nd generated by the reaction of Al and Nd,which distributed at the phase boundary and inside β phase,could also restrain the growth of α phase.Nd could improve the tensile strength and elongation of Mg-8Li-3Al alloy,however,excessive Al 2 Nd might also become crack source and decrease the elongation.展开更多
Submerged friction stir processing(SFSP)with flowing water was employed to alleviate the porosities and coarse-grained structure introduced by wire-arc manufacturing.As a result,uniform and ultrafine grained(UFG)struc...Submerged friction stir processing(SFSP)with flowing water was employed to alleviate the porosities and coarse-grained structure introduced by wire-arc manufacturing.As a result,uniform and ultrafine grained(UFG)structure with average grain size of 0.83μm was achieved with the help of sharply reduced heat input and holding time at elevated temperature.The optimized UFG structure enabled a superior combination of strength and ductility with high ultimate tensile strength and elongation of 273.17 MPa and 15.39%.Specifically,grain refinement strengthening and decentralized θ(Al_(2)Cu)phase in the sample subjected to SFSP made great contributions to the enhanced strength.In addition,the decrease in residual stresses and removal of pores substantially enhance the ductility.High rates of cooling and low temperature cycling,which are facilitated by the water-cooling environment throughout the machining process,are vital in obtaining superior microstructures.This work provides a new method for developing a uniform and UFG structure with excellent mechanical properties.展开更多
Magnetic Pulse Welding(MPW)is a very high speed process which produces solid-state welds.In this work, Welding interface microstructure of Al/Fe tubes by MPW and its influence factors were investigated.The equipment w...Magnetic Pulse Welding(MPW)is a very high speed process which produces solid-state welds.In this work, Welding interface microstructure of Al/Fe tubes by MPW and its influence factors were investigated.The equipment with a capacitor of 100 μF was used under different voltages range from 8 kV to 15 kV.SEM and TEM observation were carried out to investigate microstructure of the welding interface.The results show that the dissimilar tubes(Al/Fe)could be welded with the optimum tapered angle of about 4 degree.The welding interface in Al/Fe joints exhibits a characteristic wavy morphology with wavelength of about I00 μm.A new layer exists between base tubes consisting of AI and Fe elements.Ultrafme grained microstructure is founded near the welding interface.The results obtain in this work provide the fundamentals for the investigation of MPW mechanism of dissimilar tubes.展开更多
Ultrafine-grained(UFG)materials exhibit high strengths due to grain boundary strengthening,but grains can grow rapidly if post heat treatment is required,making it challenging to achieve grain boundary and precipitati...Ultrafine-grained(UFG)materials exhibit high strengths due to grain boundary strengthening,but grains can grow rapidly if post heat treatment is required,making it challenging to achieve grain boundary and precipitation strengthening simultaneously.Grain growth stagnation at 525℃(0.87 T_(m),melting point)was observed in a Mg-4Y-3RE alloy fabricated by additive friction stir deposition(AFSD),a novel solidstate additive manufacturing technology.The AFSD processing produced a UFG microstructure and two major second phases,Mg_(41)RE_(5)and nanoparticles containing Y and O.After solid solution treatment(SST)at 525℃for 72 h,no noticeable grain growth occurred.While Mg_(41)RE_(5)particles dissolved into the matrix within 4 h of SST,the nanoparticles remained stable and unaltered.The observed grain growth stagnation is attributed to Zener pinning by these thermally stable nanoparticles.These new findings offer a novel approach to designing UFG materials with exceptional thermal stability for high-temperature applications.展开更多
In order to examine the effect of extrusion ratio on the microstructure and mechanical behavior in Al-Cu-Mg-Ag alloy, the Al-6.3 Cu-0.48 Mg-0.4 Ag alloy was subjected to extruding with different extrusion ratios of 17...In order to examine the effect of extrusion ratio on the microstructure and mechanical behavior in Al-Cu-Mg-Ag alloy, the Al-6.3 Cu-0.48 Mg-0.4 Ag alloy was subjected to extruding with different extrusion ratios of 17, 30 and 67. The results indicate that the grains are refined and the strength is improved effectively with increasing extrusion ratio. However, further investigation shows that the extrusion ratio of 30 is more effective than the lower extrusion ratio（17） and the higher extrusion ratio（67） to refine the grains in the T6-temper alloy. Moreover, the sample with an extrusion ratio of 30 obtains more precipitates and superior mechanical properties after T6 treatment. This study supports the idea that there exists a critical extrusion ratio for grain refinement and improvement of mechanical properties for the T6-temper alloy. Recrystallization and precipitation during T6 treatment were introduced to explain the effects of extrusion ratio on the microstructure and mechanical properties of the Al-Cu-Mg-Ag alloys.展开更多
Five forging experiments were designed and conducted to investigate the effect of process parameters on microstructure evolution during hot deformation for X12CrMoWVNbN10-1-1 steel.The experimental results indicated t...Five forging experiments were designed and conducted to investigate the effect of process parameters on microstructure evolution during hot deformation for X12CrMoWVNbN10-1-1 steel.The experimental results indicated that average grain size became finer with the increasing number of upsetting and stretching.Especially,the size of stretching three times with upsetting twice had the most remarkable effect on refinement,and the size was only 27.36%of the original one.Moreover,the stress model was integrated into the software and finite element models were established.Simulation results demonstrated that the strain at center point of workpiece was far larger than critical strain value in each process,so that dynamic recrystallization(DRX) occurred in each workpiece,which implied DRX could occur for several times with the increasing number of upsetting and stretching,and uniform finer microstructure would be obtained.However,the results also showed that higher temperature was an unfavorable factor for grain refinement,so the times of heating should be limited for workpiece,and as many forging processes as possible should be finished in once heating.展开更多
Results of a large set of tensile and compressive creep tests on pure Al were reanalyzed for the influence of low-and high-angle grain boundaries on the deformation resistance at the temperature T = 473 K = 0.51 Tmwhe...Results of a large set of tensile and compressive creep tests on pure Al were reanalyzed for the influence of low-and high-angle grain boundaries on the deformation resistance at the temperature T = 473 K = 0.51 Tmwhere Tm is the melting point.Thermomechanical treatment by equal channel angular pressing followed by heating to T led to strong increase of areal fraction of high-angle boundaries in a structure of subgrains of ≈10^-6m in size,accompanied by significant reduction of subgrain strengthening and of the stress sensitivity of the deformation rate.（Sub）grain strengthening by low-angle boundaries is most effective;the strengthening effect virtually disappears during creep as the boundary spacings coarsen toward their stress-dependent,quasi-stationary size wqs.The same type of coarsening is found for（sub）grain structures with large fraction of high-angle boundaries;in the quasi-stationary state they lead to softening at low and strengthening at high stresses,and a significant increase in tensile fracture strain to values up to 0.8.The results are analogous to former results for Cu and are explained in the same way by the influence of boundaries on storage and recovery of crystal defects and the homogenization of glide.展开更多
The microstructural evolution and tensile properties of Ti-3Al-8V-6Cr-4Mo-xZr（x = 0,2,4 and 6） titanium alloys were investigated.The precipitated phases and tensile fracture morphologies were observed using scanning...The microstructural evolution and tensile properties of Ti-3Al-8V-6Cr-4Mo-xZr（x = 0,2,4 and 6） titanium alloys were investigated.The precipitated phases and tensile fracture morphologies were observed using scanning electron microscopy and transmission electron microscopy.Experimental results show that the presence of trace impurity Si and the addition of Zr induce the formation of（TiZr）_6Si_3 silicides.The quantity of silicides increases with Zr content increasing.The dispersed silicides refined the grain size of β Zr-containing alloys,and the grain size decreases significantly with Zr content increasing.Accompanying these microstructural changes,the strength of the alloys is enhanced gradually with the increase of Zr content,which is attributed to the combination of precipitation strengthening and grain refinement.展开更多
Asymmetrical hot rolling（ASHR） was proposed to acquire productive grain refinement for Fe-20Mn-4Al-0.3C and Fe-18Cr-18Mn-0.5N non-magnetic austenitic steels. The intensive additional shear deformation caused by ASHR...Asymmetrical hot rolling（ASHR） was proposed to acquire productive grain refinement for Fe-20Mn-4Al-0.3C and Fe-18Cr-18Mn-0.5N non-magnetic austenitic steels. The intensive additional shear deformation caused by ASHR promotes the nucleation of recrystallization and grain refining of steel plates. With the speed ratio of 1.2, the austenitic grains were refined to ~5 m on the surface, the recrystallization fraction was enhanced to ~34.7%, and the thickness of fine-grained surface layer increases to ~450m for Fe-20Mn-4Al-0.3 C steel. The Fe-18Cr-18Mn-0.5N steel also exhibited an effective surface grain refinement with an average size of ~3μm, and the recrystallization fraction reached ~76.9% at the speed ratio of 1.15.展开更多
Ultra-high strength Al alloy system was developed by cryorolling and the contribution of various strengthening mechanisms to the overall yield strength of the system was evaluated. Cryorolling of Al-4%Cu-3%TiB2 in sit...Ultra-high strength Al alloy system was developed by cryorolling and the contribution of various strengthening mechanisms to the overall yield strength of the system was evaluated. Cryorolling of Al-4%Cu-3%TiB2 in situ composite followed by short annealing at 175 ℃ and ageing at 125℃ resulted in an ultra-high yield strength of about 800 MPa with 9%total elongation. The strengthening contributions form solid solution strengthening, grain refinement, dislocation strengthening, precipitation hardening and dispersion strengthening were evaluated using standard equations. It was estimated that the maximum contribution was from grain refinement due to cryorolling followed by precipitation and dispersion strengthening.展开更多
Ultrafine-grained(UFG) hypereutectic Al-23%Si (mass fraction) alloy was achieved through equal-channel angular pressing(EACP) procedure. And the electrochemical properties after various ECAP passes were investigated i...Ultrafine-grained(UFG) hypereutectic Al-23%Si (mass fraction) alloy was achieved through equal-channel angular pressing(EACP) procedure. And the electrochemical properties after various ECAP passes were investigated in neutral NaCl solution. Potentiostatic polarization curves show that the corrosion potential of the ECAPed sample after 4 passes decreases markedly, while the corrosion current density reaches 1.37 times that of the as-cast alloy. However, the φcorr and Jcorr values after 16 passes are improved and approach those of the as-cast alloy. Immersion tests also show that the mass-loss ratio of ECAPed alloy decreases with increasing the pressing pass, which is lowered to 28.7% with the increase of pass number from 4 to 16. Pitting susceptibility of the ECAPed alloy after initial 4 passes is boosted, due to the presence of biggish voids resulted from the breakage of brittle large primary silicon crystals during ECAP. Increasing ECAP pass makes the voids evanesce and results in the homogeneous ultrafine-grained structure, contributing to a higher pitting resistance. These results indicate that enough ECAP passes are beneficial to increasing corrosion resistance of the hypereutectic Al-23%Si alloy.展开更多
基金This work was supported by the National Natural Sci-ence Foundation of China under grant No.50171009the National 863 Program of China(No.2002A A305501)Part work was performed at IMM RWTH A achen,Germany.
文摘Channel die compression and initial textures are used to activate different deformation mechanisms in a fine-grained magnesium alloy AZ31. The σ-ε curves, microstructures and, particularly, textures are analyzed to reveal different deformation mechanisms and to compare with those of coarse grained samples. Dominant double-prismatic slip, {1012} twinning and basal slip are detected in three types of samples, respectively, which is similar to those of coarse grained samples. The detrimental effect of shear band formation or {1011} twinning is limited in fine grained microstructure. In addition to the higher flow stress at low temperature an early decrease in flow stress at higher temperature is also found in fine-grained samples in comparison with their coarse-grained counterparts. This softening is ascribed to the early dynamic recrystallization or grain boundary glide.
基金Funded by the Taiyuan Special Fund for Sci-Tech Star (No. 09121002)the Youth Science Foundation of Shanxi Province (No.2008021033)Shanxi Research Fund for Returned Scholars (No.2007-25)
文摘An as-cast magnesium alloy with high Al content Mg15Al was subjected to equal-channel angular pressing （ECAP） through a die with an angle of φ= 90？ at 553 K following route Bc. It is found that the network β-Mg17Al12 phases in the as-cast Mg15Al alloy are broken into small blocks and dispersed uniformly with increasing numbers of pressing passes. Moreover, many nano-sized Mg17Al12 particles precipitate in the ultra-fine α-Mg matrix. The grains are obviously refined. However, the grain structure is inhomogeneous in different areas of the alloy. The average size of the primary phase α-Mg is reduced to about 1 μm while grains of around 0.1-0.2 μm are obtained in some two-phase areas. With additional ECAP passes （up to 8）, coarsening of the grains occurs by dynamic recovery. Room temperature tensile tests show that the mechanical properties of Mg15Al alloys are markedly improved after 4 ECAP passes. The ultimate tensile strength and elongation to failure increase from 150 MPa to 269.3 MPa and from 0.05% to 7.4%, respectively. Compared with that after 4 passes, the elongation to failure of the alloy increases but the strength of the alloy slightly decreases after 8 ECAP passes. Fracture morphology of the ECAP-processed alloy exhibits dimple-like fracture characteristics while the as-cast alloy shows quasi-cleavage fractures.
基金supported by the National High-Tech.R&D Programo f China(the National 863 plans projects,Grant No.2007AA03Z352)
文摘An ultrafine grained microstructure was obtained for 304 stainless steel(304SS)sheets by using surface nanocrystallization and warm-rolling.The microstructure and mechanical properties were determined by X-ray diffraction(XRD),transmission electron microscope(TEM)and a test on microhardness.Experimental results were shown that the microstructure was featured by a continuous distribution from the nanocrystalline on the surface to micro-grains in the center,in which the volume fraction of the micro-sized grains is about 40% in the surface layer.This multi-scale grained microstructure was composed of austenite and martensite phases with a gradient increasing volume fraction of austenite from the surface to the centre.The microhardness of the resultant steel was higher than 150% of that as received,due to the refined grains and strain-induced martensitic transformation.The hardness distribution was consistent with the microstructural variation,suggesting a good combination of high strength and improved ductility.
基金financially supported by the National Natural Science Foundation of China(Nos.51235004 and51375235)the Fundamental Research Funds for the Central Universities(No.NE2014103)the Funding for Outstanding Doctoral Dissertation in NUAA(No.BCXJ16-06)
文摘In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride（PCBN）grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.
基金Supported by the National Natural Science Foundation of China(11102139,11472195)the Natural Science Foundation of Hubei Province of China(2014CFB713)
文摘Through molecular dynamics（MD） simulation, the dependencies of temperature, grain size and strain rate on the mechanical properties were studied. The simulation results demonstrated that the strain rate from 0.05 to 2 ns–1 affected the Young＇s modulus of nickel nanowires slightly, whereas the yield stress increased. The Young＇s modulus decreased approximately linearly; however, the yield stress firstly increased and subsequently dropped as the temperature increased. The Young＇s modulus and yield stress increased as the mean grain size increased from 2.66 to 6.72 nm. Moreover, certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension. Certain phenomena such as the formation of twin structures, which were found in nanowires with larger grain size at higher strain rate and lower temperature, as well as the movement of grain boundaries and dislocation, were detected and discussed in detail. The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size. However, for larger grain size, the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.
基金the National Natural Science Foundation of China(No.51975593)the Hunan Provincial Natural Science Foundation of China(No.2020JJ4113)the Science and Technology Innovation Planning Project of Hunan Province(No.2019XK2301)。
文摘The uniform refinement mechanisms and methods of deformed mixed and coarse grains inside a solution-treatment Ni-based superalloy during two-stage annealing treatment have been investigated.The two-stage heat treatment experiments include an aging annealing treatment(AT)and a subsequent recrystallization annealing treatment(RT).The object of AT is to precipitate someδphases and consume part of storage energy to inhibit the grain growth during RT,while the RT is to refine mixed and coarse grains by recrystallization.It can be found that the recrystallization grains will quickly grow up to a large size when the AT time is too low or the RT temperature is too high,while the deformed coarse grains cannot be eliminated when the AT time is too long or the RT temperature is too low.In addition,the mixed microstructure composed of some abnormal coarse recrystallization grains(ACRGs)and a large number of fine grains can be observed in the annealed specimen when the AT time is 3 h and RT temperature is 980℃.The phenomenon attributes to the uneven distribution ofδphase resulted from the heterogeneous deformation energy when the AT time is too short.In the regions with a large number ofδphases,the recrystallization nucleation rate is promoted and the growth of grains is limited,which results in fine grains.However,in the regions with fewδphases,the recrystallization grains around grain boundaries can easily grow up,and the new recrystallization nucleus is difficult to form inside grain,which leads to ACRGs.Thus,in order to obtain uniform and fine annealed microstructure,it is a prerequisite to precipitate even-distributedδphase by choosing a suitable AT time,such as 12 h.Moreover,a relative high RT temperature is also needed to promote the recrystallization nucleation aroundδphase.The optimal annealing parameters range for uniformly refining mixed crystal can be summarized as:900℃×12 h+990℃×(40-60 min)and 900℃×12 h+1000℃×(10-15 min).
基金Project(51374025) supported by the National Natural Science Foundation of ChinaProject(2014Z-05) supported by the State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing,ChinaProject(2152020) supported by the Beijing Natural Science Foundation,China
文摘Cu-4.7%Sn （mass fraction） alloy plate was prepared by the self-developed two-phase zone continuous casting （TZCC） process. The relationship between process parameters of TZCC and surface quality of the alloy plate was investigated. The microstructure and mechanical properties of the TZCC alloy plate were analyzed. The results show that Cu-4.7%Sn alloy plate with smooth surface can be obtained by means of reasonable matching the entrance temperature of two-phase zone mold and the continuous casting speed. The microstructure of the TZCC alloy is composed of grains-covered grains, small grains with self-closed grain boundaries, columnar grains and equiaxed grains. Compared with cold mold continuous casting Cu-4.7%Sn alloy plate, the room temperature tensile strength and ductility of the TZCC alloy plate are greatly improved.
文摘Friction stir processing （FSP）, a variation of FSW （friction stir welding） is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the mechanical properties of material. FSP can also produce fine grained microstructures through the thickness to impart superplasticity. The technology involves plunging a rapidly rotating, non consumable tool, comprising a profiled pin and larger diameter shoulder, into the surface and then traversing the tool across the surface. The pin and the shoulder friction heat the surface which alters the grain structure in the processed area thereby improving the mechanical properties. This paper presents the effects of FSP on microstructure and mechanical properties of extruded cast 2285 aluminum alloy at three different feed rates viz. 10, 12 and 15 mm/min. With the increase in the feed speed the material was observed to have increased impact strength. FSP also increased the tensile and yield strengths with increases in hardness and ductility values also. The observation has been listed in detail and pictorially represented.
基金supported by the German Research Foundation(DFG)the DFG for funding the subproject B3 and C5 of the Collaborative Research Center 666 "Integral sheet metal design with higher order bifurcations-Development,Production,Evaluation″
文摘The effects of milling parameters on the surface quality,microstructures and mechanical properties of machined parts with ultrafine grained(UFG)gradient microstructures are investigated.The effects of the cutting speed,feed per tooth,cutting tool geometry and cooling strategy are demonstrated.It has been found that the surface quality of machined grooves can be improved by increasing the cutting speed.However,cryogenic cooling with CO_2 exhibits no significant improvement of surface quality.Microstructure and hardness investigations revealed similar microstructure and hardness variations near the machined groove walls for both utilized tool geometries.Therefore,cryogenic cooling can decrease more far-ranging hardness reductions due to high process temperatures,especially in the UFG regions of the machined parts,whilst it cannot prevent the drop in hardness directly at the groove walls.
基金supported by the National High Technology Research and Development Program ("863" Program) of China (2009AA03Z525)the Program of New Century Excellent Talents of the Ministry of Education of China (NCET-08-0080)+1 种基金the Science and Technology Fund of Dalian City (2009J21DW003)the Fundamental Research Funds for the Central Universities (DUT11ZD115)
文摘Effects of Nd on microstructure and mechanical properties of as-cast Mg-8Li-3Al alloy were investigated by OM,X-ray diffraction（XRD）,EPMA,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS）.The results showed that the dendrites sizes of α phase were decreased by the Nd addition.When the amount of addition Nd was 1.6 wt.%,the alloy with the smallest α phase was obtained.The refining mechanism mainly owed to the increasing constitutional supercooling at the solidification front.Furthermore,the compound Al 2 Nd generated by the reaction of Al and Nd,which distributed at the phase boundary and inside β phase,could also restrain the growth of α phase.Nd could improve the tensile strength and elongation of Mg-8Li-3Al alloy,however,excessive Al 2 Nd might also become crack source and decrease the elongation.
文摘Submerged friction stir processing(SFSP)with flowing water was employed to alleviate the porosities and coarse-grained structure introduced by wire-arc manufacturing.As a result,uniform and ultrafine grained(UFG)structure with average grain size of 0.83μm was achieved with the help of sharply reduced heat input and holding time at elevated temperature.The optimized UFG structure enabled a superior combination of strength and ductility with high ultimate tensile strength and elongation of 273.17 MPa and 15.39%.Specifically,grain refinement strengthening and decentralized θ(Al_(2)Cu)phase in the sample subjected to SFSP made great contributions to the enhanced strength.In addition,the decrease in residual stresses and removal of pores substantially enhance the ductility.High rates of cooling and low temperature cycling,which are facilitated by the water-cooling environment throughout the machining process,are vital in obtaining superior microstructures.This work provides a new method for developing a uniform and UFG structure with excellent mechanical properties.
基金Item Sponsored by National Basic Research Program of China (973 Program) [2011CB012805]Funds of State Key Laboratory of Advanced Welding and Joining[AWPT-M05]
文摘Magnetic Pulse Welding(MPW)is a very high speed process which produces solid-state welds.In this work, Welding interface microstructure of Al/Fe tubes by MPW and its influence factors were investigated.The equipment with a capacitor of 100 μF was used under different voltages range from 8 kV to 15 kV.SEM and TEM observation were carried out to investigate microstructure of the welding interface.The results show that the dissimilar tubes(Al/Fe)could be welded with the optimum tapered angle of about 4 degree.The welding interface in Al/Fe joints exhibits a characteristic wavy morphology with wavelength of about I00 μm.A new layer exists between base tubes consisting of AI and Fe elements.Ultrafme grained microstructure is founded near the welding interface.The results obtain in this work provide the fundamentals for the investigation of MPW mechanism of dissimilar tubes.
基金supported by the UKRI Future Leaders Fellowship,[MR/T019123/2]。
文摘Ultrafine-grained(UFG)materials exhibit high strengths due to grain boundary strengthening,but grains can grow rapidly if post heat treatment is required,making it challenging to achieve grain boundary and precipitation strengthening simultaneously.Grain growth stagnation at 525℃(0.87 T_(m),melting point)was observed in a Mg-4Y-3RE alloy fabricated by additive friction stir deposition(AFSD),a novel solidstate additive manufacturing technology.The AFSD processing produced a UFG microstructure and two major second phases,Mg_(41)RE_(5)and nanoparticles containing Y and O.After solid solution treatment(SST)at 525℃for 72 h,no noticeable grain growth occurred.While Mg_(41)RE_(5)particles dissolved into the matrix within 4 h of SST,the nanoparticles remained stable and unaltered.The observed grain growth stagnation is attributed to Zener pinning by these thermally stable nanoparticles.These new findings offer a novel approach to designing UFG materials with exceptional thermal stability for high-temperature applications.
基金Funded by the National Natural Science Foundation of China(No.51071075)the Deep Continental Scientific Drilling Equipment Development(Sino Probe-09-05)by the 985 Project-Automotive Engineering of Jilin University
文摘In order to examine the effect of extrusion ratio on the microstructure and mechanical behavior in Al-Cu-Mg-Ag alloy, the Al-6.3 Cu-0.48 Mg-0.4 Ag alloy was subjected to extruding with different extrusion ratios of 17, 30 and 67. The results indicate that the grains are refined and the strength is improved effectively with increasing extrusion ratio. However, further investigation shows that the extrusion ratio of 30 is more effective than the lower extrusion ratio（17） and the higher extrusion ratio（67） to refine the grains in the T6-temper alloy. Moreover, the sample with an extrusion ratio of 30 obtains more precipitates and superior mechanical properties after T6 treatment. This study supports the idea that there exists a critical extrusion ratio for grain refinement and improvement of mechanical properties for the T6-temper alloy. Recrystallization and precipitation during T6 treatment were introduced to explain the effects of extrusion ratio on the microstructure and mechanical properties of the Al-Cu-Mg-Ag alloys.
基金the National Science and Technology Major Project of China(No.2012ZX04012-011-02)the National Basic Research Program(973)of China(No.2011CB012903)
文摘Five forging experiments were designed and conducted to investigate the effect of process parameters on microstructure evolution during hot deformation for X12CrMoWVNbN10-1-1 steel.The experimental results indicated that average grain size became finer with the increasing number of upsetting and stretching.Especially,the size of stretching three times with upsetting twice had the most remarkable effect on refinement,and the size was only 27.36%of the original one.Moreover,the stress model was integrated into the software and finite element models were established.Simulation results demonstrated that the strain at center point of workpiece was far larger than critical strain value in each process,so that dynamic recrystallization(DRX) occurred in each workpiece,which implied DRX could occur for several times with the increasing number of upsetting and stretching,and uniform finer microstructure would be obtained.However,the results also showed that higher temperature was an unfavorable factor for grain refinement,so the times of heating should be limited for workpiece,and as many forging processes as possible should be finished in once heating.
基金support by the Central European Institute of Technology CEITEC(Project CZ.1.05/1.1.00/02.0068 and the European Regional Development Fund)
文摘Results of a large set of tensile and compressive creep tests on pure Al were reanalyzed for the influence of low-and high-angle grain boundaries on the deformation resistance at the temperature T = 473 K = 0.51 Tmwhere Tm is the melting point.Thermomechanical treatment by equal channel angular pressing followed by heating to T led to strong increase of areal fraction of high-angle boundaries in a structure of subgrains of ≈10^-6m in size,accompanied by significant reduction of subgrain strengthening and of the stress sensitivity of the deformation rate.（Sub）grain strengthening by low-angle boundaries is most effective;the strengthening effect virtually disappears during creep as the boundary spacings coarsen toward their stress-dependent,quasi-stationary size wqs.The same type of coarsening is found for（sub）grain structures with large fraction of high-angle boundaries;in the quasi-stationary state they lead to softening at low and strengthening at high stresses,and a significant increase in tensile fracture strain to values up to 0.8.The results are analogous to former results for Cu and are explained in the same way by the influence of boundaries on storage and recovery of crystal defects and the homogenization of glide.
文摘The microstructural evolution and tensile properties of Ti-3Al-8V-6Cr-4Mo-xZr（x = 0,2,4 and 6） titanium alloys were investigated.The precipitated phases and tensile fracture morphologies were observed using scanning electron microscopy and transmission electron microscopy.Experimental results show that the presence of trace impurity Si and the addition of Zr induce the formation of（TiZr）_6Si_3 silicides.The quantity of silicides increases with Zr content increasing.The dispersed silicides refined the grain size of β Zr-containing alloys,and the grain size decreases significantly with Zr content increasing.Accompanying these microstructural changes,the strength of the alloys is enhanced gradually with the increase of Zr content,which is attributed to the combination of precipitation strengthening and grain refinement.
基金financially supported by the National Natural Science Foundation of China(Grant No.51274062)the Research Fund for the Doctoral Program of Higher Education of China(Grant No.20130042110040)
文摘Asymmetrical hot rolling（ASHR） was proposed to acquire productive grain refinement for Fe-20Mn-4Al-0.3C and Fe-18Cr-18Mn-0.5N non-magnetic austenitic steels. The intensive additional shear deformation caused by ASHR promotes the nucleation of recrystallization and grain refining of steel plates. With the speed ratio of 1.2, the austenitic grains were refined to ~5 m on the surface, the recrystallization fraction was enhanced to ~34.7%, and the thickness of fine-grained surface layer increases to ~450m for Fe-20Mn-4Al-0.3 C steel. The Fe-18Cr-18Mn-0.5N steel also exhibited an effective surface grain refinement with an average size of ~3μm, and the recrystallization fraction reached ~76.9% at the speed ratio of 1.15.
基金the Department of Science & Technology (DST) for their financial support for carrying out this research through Fast Track Scheme (DST Sanction No: SR/FT/ET-005/2008)Technical Education Quality Improvement Programme (TEQIP)
文摘Ultra-high strength Al alloy system was developed by cryorolling and the contribution of various strengthening mechanisms to the overall yield strength of the system was evaluated. Cryorolling of Al-4%Cu-3%TiB2 in situ composite followed by short annealing at 175 ℃ and ageing at 125℃ resulted in an ultra-high yield strength of about 800 MPa with 9%total elongation. The strengthening contributions form solid solution strengthening, grain refinement, dislocation strengthening, precipitation hardening and dispersion strengthening were evaluated using standard equations. It was estimated that the maximum contribution was from grain refinement due to cryorolling followed by precipitation and dispersion strengthening.
基金Project supported by the Japanese Society for the Promotion of Science Project supported by Qing Lan Program (Jiangsu, China)
文摘Ultrafine-grained(UFG) hypereutectic Al-23%Si (mass fraction) alloy was achieved through equal-channel angular pressing(EACP) procedure. And the electrochemical properties after various ECAP passes were investigated in neutral NaCl solution. Potentiostatic polarization curves show that the corrosion potential of the ECAPed sample after 4 passes decreases markedly, while the corrosion current density reaches 1.37 times that of the as-cast alloy. However, the φcorr and Jcorr values after 16 passes are improved and approach those of the as-cast alloy. Immersion tests also show that the mass-loss ratio of ECAPed alloy decreases with increasing the pressing pass, which is lowered to 28.7% with the increase of pass number from 4 to 16. Pitting susceptibility of the ECAPed alloy after initial 4 passes is boosted, due to the presence of biggish voids resulted from the breakage of brittle large primary silicon crystals during ECAP. Increasing ECAP pass makes the voids evanesce and results in the homogeneous ultrafine-grained structure, contributing to a higher pitting resistance. These results indicate that enough ECAP passes are beneficial to increasing corrosion resistance of the hypereutectic Al-23%Si alloy.
