Rolling contact fatigue performance is among the most important issues for applications of bearing steels.In this work,a recently developed surface modification technique,surface mechanical rolling treatment,was appli...Rolling contact fatigue performance is among the most important issues for applications of bearing steels.In this work,a recently developed surface modification technique,surface mechanical rolling treatment,was applied on a rare-earth addition bearing steel.And rolling contact fatigue behavior of treated samples was compared with that of as-received counterparts at different contacting stresses.The results demonstrated that a 700μm-thick gradient nanostructured surface layer is produced on samples by surface mechanical rolling treatment.The grain size decreases while the microhardness increases gradually with decreasing depth,reaching~23 nm and~10.2 GPa,respectively,at the top surface.Consequently,the rolling contact fatigue property is significantly enhanced.The characteristic life of treated samples is~3.2 times that of untreated counterparts according to Weibull curves at 5.6 GPa.Analyses of fatigue mechanisms demonstrated that the gradient nanostructured surface layer might not only retard material degradation and microcrack formation,but also prolong the steady-state elastic response stage under rolling contact fatigue.展开更多
In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and mat...In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and material properties of sample at various depths from the topmost surface were investigated by SEM, TEM, XRD, OM etc. The experimental results show that the gradient nano/micro-structure was introduced into the surface layer of over 100μm in thickness. The remarkable increase in hardness near the topmost surface was mainly attributed to the reduced grain size. The equiaxed nano-sized grains were in random orientation and the most of their boundaries were low-angle grain boundaries （LAGBs）. The coarse grains are refined into the few micro-sized grains by dislocation activities;deformation twinning was found to be the primary form for the formation of submicron grains;the formation of nanostructure was dominated by dislocation activities accompanied with rotation of grains in local region.展开更多
Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of ...Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.展开更多
A facile route for preparation of gradient wettability surface on copper substrate with contact angle changing from 90.3°to4.2°was developed.The Cu（OH）2 nanoribbon arrays were electrochemically deposited o...A facile route for preparation of gradient wettability surface on copper substrate with contact angle changing from 90.3°to4.2°was developed.The Cu（OH）2 nanoribbon arrays were electrochemically deposited on copper foil via a modified anodization technology,and the growth degree and density of the Cu（OH）2 arrays may be controlled varying with position along the substrate by slowly adding aqueous solution of KOH into the two-electrode cell of an anodization system to form the gradient surface.The prepared surface was water resistant and thermal stable,which could keep its gradient wetting property after being immersed in water bath at 100℃ for 10 h.The results of scanning electron microscopy（SEM）,X-ray diffraction（XRD） and X-ray photoelectron spectroscopy（XPS） demonstrate that the distribution of Cu（OH）2 nanoribbon arrays on copper surface are responsible for the gradient wettability.展开更多
In this work,ultrasonic surface rolling process(USRP)was utilized to produce a gradient structured layer on 7 B50-T7751 aluminum alloy,and the mechanical properties and corrosion fatigue behavior of treated samples we...In this work,ultrasonic surface rolling process(USRP)was utilized to produce a gradient structured layer on 7 B50-T7751 aluminum alloy,and the mechanical properties and corrosion fatigue behavior of treated samples were studied.These results reveal that underwent USRP,a 425~m thick gradient structure and a 700~m deep compressive residual stress field are created,aluminum grain size become fine(~67 nm),and the corrosion rate of treated surface reduces by 60.08%owing to the combined effect of compressive residual stress and surface nanocrystallization.The corrosion fatigue strength is enhanced to 117%of that of 7 B50 Al alloys by means of USRP due to the introduced compressive residual stress,which is considered as the major favorable factor in suppressing the initiation and early propagation of corrosion fatigue cracks.Besides,the gradient structure is an important factor in providing a significant synergistic contribution to the improvement of corrosion fatigue performance.展开更多
In this pap er, a novel size-dep endent functionally graded (FG) cylindrical shell model is develop ed based on the nonlocal strain gradient theory in conjunction with the Gurtin-Murdoch surface elasticity theory . Th...In this pap er, a novel size-dep endent functionally graded (FG) cylindrical shell model is develop ed based on the nonlocal strain gradient theory in conjunction with the Gurtin-Murdoch surface elasticity theory . The new model containing a nonlocal parameter, a material length scale parameter, and several surface elastic constants can capture three typical typ es of size e ects simultaneously , which are the nonlocal stress ef- fect, the strain gradient e ect, and the surface energy e ects. With the help of Hamilton’s principle and rst-order shear deformation theory , the non-classical governing equations and related b oundary conditions are derived. By using the prop osed model, the free vibra- tion problem of FG cylindrical nanoshells with material prop erties varying continuously through the thickness according to a p ower-law distribution is analytically solved, and the closed-form solutions for natural frequencies under various b oundary conditions are obtained. After verifying the reliability of the prop osed model and analytical method by comparing the degenerated results with those available in the literature, the in uences of nonlocal parameter, material length scale parameter, p ower-law index, radius-to-thickness ratio, length-to-radius ratio, and surface e ects on the vibration characteristic of func- tionally graded cylindrical nanoshells are examined in detail.展开更多
Nanolaminated structures composed of low-angle grain boundaries(LAGBs) possess high thermal stability. In this paper, a gradient nanolaminated(GNL) surface layer with smooth finish was fabricated on an interstitial-fr...Nanolaminated structures composed of low-angle grain boundaries(LAGBs) possess high thermal stability. In this paper, a gradient nanolaminated(GNL) surface layer with smooth finish was fabricated on an interstitial-free steel by means of surface mechanical rolling treatment. Microstructural observations demonstrated that the average lamellar thickness is about 80 nm in the topmost surface layer and increases with increasing depth. High thermal stability was confirmed in the GNL surface layer after annealing at 500℃. Diffusion measurements showed that effective diffusivity of Cr in GNL layer is 4–6 orders of magnitude higher than lattice diffusivity within the temperature range from 400 to 500℃. This might be attributed to numerous LAGBs or dislocation structures with a higher energy state in the GNL surface layer. This work demonstrates the possibility to advanced chromizing(or other surface alloying)processes of steels with formation of GNL surface layer, so that a thicker alloyed surface layer with a stable nanostructure is achieved.展开更多
In the present work, an ultrahigh strength bearing steel（AISI 52100） was subjected to surface mechanical rolling treatment（SMRT） at room temperature. Microstructural observations showed that martensitic laths, twi...In the present work, an ultrahigh strength bearing steel（AISI 52100） was subjected to surface mechanical rolling treatment（SMRT） at room temperature. Microstructural observations showed that martensitic laths, twins and cementite particles in the initial microstructure underwent distinct plastic strains and were gradually refined into nanostructures. Consequently, a gradient nanostructured（GNS） surface layer with a mean grain size of -24 nm at the top surface was obtained on the bearing steel, resulting in an increment of -20% in the surface hardness. Analyses based on microstructural evolution, phase constitution and in-depth hardness distribution revealed a mechanically induced formation mechanism of the GNS surface layer. The multiple surface severe plastic deformation under fine lubrication and cooling during SMRT contributed to the formation of a thick hardened surface layer on the bearing steel.展开更多
Nanocrystalline surface layers and gradient nanostructure in 5182 aluminum alloy have been produced through surface mechanical attrition treatment(SMAT). The results indicate that the gradient nanostructure can not on...Nanocrystalline surface layers and gradient nanostructure in 5182 aluminum alloy have been produced through surface mechanical attrition treatment(SMAT). The results indicate that the gradient nanostructure can not only improve the mechanical properties of 5182 Al alloy, but also has a certain effect on the Portevin-Le Chatelier(PLC) effect. The yield and ultimate tensile strength of 5182 Al alloy with SMAT are significantly improved combining with the decrease of fracture elongation compared with the as-received one. The PLC effect of 5182 Al alloy could be effectively postponed by the formation of gradient nanostructure after SMAT. It leads to the increase of critical strain of the PLC effect, more concentrated distribution of serrated strain, and increase of average stress amplitude in special strain range. The influence of grain size and gradient nanostructure on the PLC effect of 5182 Al alloy was also discussed in detail. Grain refinement could sharply increase the density of dislocations and hinder the movement of dislocations, which results in the decrease of moving speed of dislocations and the more concentrated distribution of solute atoms. The solute atoms would aggregate to form nano precipitates and further impede movement of dislocation. The stronger interaction between the dislocations and the nano precipitates is the main mechanism of postponed PLC effect.展开更多
The separation optimization of nine organic and inorganic anions in tobacco leaves using gradient ion chromatography by response surface methodology was investigated.In order to achieve this goal the usefulness of the...The separation optimization of nine organic and inorganic anions in tobacco leaves using gradient ion chromatography by response surface methodology was investigated.In order to achieve this goal the usefulness of the chromatographic response function（CRF） for the evaluation of the two different chromatographic performance goals（resolution and analysis time） was tested. The experiments were performed according to a Box-Behnken design response surface experimental design.展开更多
Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force ap...Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.展开更多
The microstructure,hardness and tensile properties have been studied in copper processed by high pressure surface rolling(HPSR)both in the as-deformed condition and after subsequent annealing at 150℃.It is found that...The microstructure,hardness and tensile properties have been studied in copper processed by high pressure surface rolling(HPSR)both in the as-deformed condition and after subsequent annealing at 150℃.It is found that a gradient structure with significant differences in the scale of microstructural features is formed by HPSR.The deformed microstructure varies from nano-and ultrafine-scale structures with a large fraction of high angle boundaries near the surface to lightly deformed grains at depths of 1-3 mm below the surface.Tensile tests of 1-mm-thick specimens demonstrate that the asdeformed material has a high strength and a low uniform elongation.Annealing at 150℃results in partial recrystallization,which creates new through-thickness gradients.Except for the topmost layer and several bands in the adjacent layer,recrystallization is more pronounced close to the surface.The fraction recrystallized is at least 80%at depths of 60-300μm after annealing for 960 min.The fraction recrystallized in the subsurface decreases with increasing depth,and the deformed layer at depths greater than 500μm re-mains largely non-recrystallized after annealing.This partially recrystallized condition demonstrates an improved combination of strength and ductility.展开更多
In this paper,plasma fluorination is combined with plasma silicon deposition to achieve step gradient modification on an epoxy resin surface.The physicochemical characteristics of samples are investigated and the elec...In this paper,plasma fluorination is combined with plasma silicon deposition to achieve step gradient modification on an epoxy resin surface.The physicochemical characteristics of samples are investigated and the electrical performances measured.The obtained results show that compared with untreated and single treated samples,the samples treated by step gradient modification significantly improve the flashover performance.According to experiment and simulation,the mechanism explanations are summarized as follows.First,it is found that the step gradient conductivity can effectively optimize the electric field distribution of a needle-needle electrode.Then,step gradient modification suppresses the accumulation of surface charge at the triple junction and makes the charge distribution more uniform.Furthermore,it can accelerate the surface dissipation on a high electrical field region and control the dissipation rate on a low electrical field region.All these results can restrain surface discharge and increase the flashover voltage.The step gradient modification method proposed in this paper provides a new idea for improving the surface insulation performance.展开更多
Heterogeneous gradient nanostructured metals have been shown to achieve the strength-ductility synergy, thus potentially possessing the enhanced tribological performance in comparison with their homogeneous nanograine...Heterogeneous gradient nanostructured metals have been shown to achieve the strength-ductility synergy, thus potentially possessing the enhanced tribological performance in comparison with their homogeneous nanograined counterparts. In this work, a facile laser surface remelting-based surface treatment technique is developed to fabricate a gradient nanostructured layer on a TiZrHfTaNb refractory highentropy alloy. The characterization of the microstructural evolution along the depth direction from the matrix to the topmost surface layer shows that the average grain size in the ~100 μm-thick gradient nanostructured layer is dramatically refined from the original ~200 μm to only ~8 nm in the top surface layer. The microhardness is therefore gradually increased from ~240 HV in matrix to ~650 HV in the topmost surface layer, approximately 2.7 times. Noticeably, the original coarse-grained single-phase bodycentered-cubic TiZrHfTaNb refractory high-entropy alloy is gradually decomposed into TiNb-rich bodycentered-cubic phase, TaNb-rich body-centered-cubic phase, ZrHf-rich hexagonal-close-packed phase and TiZr Hf-rich face-centered-cubic phase with gradient distribution in grain size along the depth direction during the gradient refinement process. As a result, the novel laser surface treatment-introduced gradient nanostructured TiZrHfTaNb refractory high-entropy alloy demonstrates the significantly improved wear resistance, with the wear rate reducing markedly by an order of magnitude, as compared with the as-cast one. The decomposed multi-phases and gradient nanostructures should account for the enhanced wear resistance. Our findings provide new insights into the refinement mechanisms of the laser-treated refractory high-entropy alloys and broaden their potential applications via heterogeneous gradient nanostructure engineering.展开更多
Copper foils with gradient structure in thickness direction and different roughnesses on two surfaces were fabricated by double rolling. The two surface morphologies of double-rolled copper foils are quite different, ...Copper foils with gradient structure in thickness direction and different roughnesses on two surfaces were fabricated by double rolling. The two surface morphologies of double-rolled copper foils are quite different, and the surface roughness values are 61 and 1095 nm, respectively. The roughness value of matt surface can meet the requirement for bonding the resin matrix with copper foils used for flexible printed circuit boards, thus may omit traditional roughening treatment; the microstructure of double-rolled copper foils demonstrates an obviously asymmetric gradient feature. From bright surface to matt surface in thickness direction, the average grain size first increases from 2.3 to 7.4 μm and then decreases to 3.6 μm; compared with conventional rolled copper foils, the double-rolled copper foils exhibit a remarkably increased bending fatigue life, and the increased range is about 16.2%.展开更多
Magnetic field gradient tensor technique provides abundant data for delicate inversion of subsurface magnetic susceptibility distribution. Large scale magnetic data inversion imaging requires high speed and accuracy f...Magnetic field gradient tensor technique provides abundant data for delicate inversion of subsurface magnetic susceptibility distribution. Large scale magnetic data inversion imaging requires high speed and accuracy for forward modeling. For arbitrarily distributed susceptibility data on an undulated surface, we propose a fast 3D forward modeling method in the wavenumber domain based on(1) the wavenumber-domain expression of the prism combination model and the Gauss–FFT algorithm and(2) cubic spline interpolation. We apply the proposed 3D forward modeling method to synthetic data and use weighting coefficients in the wavenumber domain to improve the modeling for multiple observation surfaces, and also demonstrate the accuracy and efficiency of the proposed method.展开更多
Welded joints are usually characterized by microstructural and compositional inhomogeneities, which may significantly degrade their fatigue properties and result in unpredictable failures. The present work demonstrate...Welded joints are usually characterized by microstructural and compositional inhomogeneities, which may significantly degrade their fatigue properties and result in unpredictable failures. The present work demonstrates a novel and simple method to effectively optimize the microstructure in the surface layer and promote the fatigue properties of welded specimens. By a recently developed approach—surface mechanical rolling treatment(SMRT), a gradient nanostructured surface layer is formed on welded S355 J2 W steel specimens. The mean grain size is refined to nanometer scale, and the hardness is significantly enhanced in the SMRT surface layer. Independent of the initially inhomogeneous microstructure and hardness distributions, the microstructure and hardness distributions in the surface layers are comparable on different zones of a welded specimen after SMRT with the same procedure. Consequently, fatigue property of the SMRT specimens is significantly enhanced relative to that of the as-welded specimens within the high cycle fatigue regime.展开更多
Based on closed-orbit theory, the photodetachment of H- in a gradient electric field near a metal surface is studied. It is demonstrated that the gradient electric field has a significant influence on the photodetachm...Based on closed-orbit theory, the photodetachment of H- in a gradient electric field near a metal surface is studied. It is demonstrated that the gradient electric field has a significant influence on the photodetachment of negative ions near a metal surface. With the increase of the gradient of the electric field, the oscillation in the photodetachment cross section becomes strengthened. Besides, in contrast to the photodetachment of H- near a metal surface in a uniform electric field, the oscillating amplitude and the oscillating region in the cross section of a gradient electric field also become enlarged. Therefore, we can use the gradient electric field to control the photodetachment of negative ions near a metal surface. We hope that our results will be useful for understanding the photodetachment of negative ions in the vicinity of surfaces, cavities, and ion traps.展开更多
Layered LiCoO_(2)(LCO)acts as a dominant cathode material for lithium-ion batteries(LIBs)in 3C products because of its high compacted density and volumetric energy density.Although improving the high cutoff voltage is...Layered LiCoO_(2)(LCO)acts as a dominant cathode material for lithium-ion batteries(LIBs)in 3C products because of its high compacted density and volumetric energy density.Although improving the high cutoff voltage is an effective strategy to increase its capacity,such behavior would trigger rapid capacity decay due to the surface or/and structure degradation.Herein,we propose a bi-functional surface strategy involving constructing a robust spinel-like phase coating layer with great integrity and compatibility to LiCoO_(2) and modulating crystal lattice by anion and cation gradient co-doping at the subsurface.As a result,the modified LiCoO_(2)(AFM-LCO)shows a capacity retention of 80.9%after 500 cycles between 3.0and 4.6 V.The Al,F,Mg enriched spinel-like phase coating layer serves as a robust physical barrier to effectively inhibit the undesired side reactions between the electrolyte and the cathode.Meanwhile,the Al,F,Mg gradient co-doping significantly enhances the surficial structure stability,suppresses Co dissolution and oxygen release,providing a stable path for Li-ions mobility all through the long-term cycles.Thus,the surface bi-functional strategy is an effective method to synergistically improve the electrochemical performances of LCO at a high cut-off voltage of 4.6 V.展开更多
基金The financial supports by the Chinese Academy of Sciences(Nos.XDC04030300 and XDB0510303)CAS-HK Joint Laboratory of Nanomaterials and MechanicsShenyang National Laboratory for Materials Science are acknowledged.
文摘Rolling contact fatigue performance is among the most important issues for applications of bearing steels.In this work,a recently developed surface modification technique,surface mechanical rolling treatment,was applied on a rare-earth addition bearing steel.And rolling contact fatigue behavior of treated samples was compared with that of as-received counterparts at different contacting stresses.The results demonstrated that a 700μm-thick gradient nanostructured surface layer is produced on samples by surface mechanical rolling treatment.The grain size decreases while the microhardness increases gradually with decreasing depth,reaching~23 nm and~10.2 GPa,respectively,at the top surface.Consequently,the rolling contact fatigue property is significantly enhanced.The characteristic life of treated samples is~3.2 times that of untreated counterparts according to Weibull curves at 5.6 GPa.Analyses of fatigue mechanisms demonstrated that the gradient nanostructured surface layer might not only retard material degradation and microcrack formation,but also prolong the steady-state elastic response stage under rolling contact fatigue.
基金Project(50975095)supported by the National Natural Science Foundation of ChinaProject(2012ZM0048)supported by the Fundamental Research Funds for the Central Universities,China
文摘In order to investigate a gradient nano/micro-structured surface layer on pure copper produced by severe plasticity roller burnishing （SPRB） and grain refinement mechanism, the microstructure characteristics and material properties of sample at various depths from the topmost surface were investigated by SEM, TEM, XRD, OM etc. The experimental results show that the gradient nano/micro-structure was introduced into the surface layer of over 100μm in thickness. The remarkable increase in hardness near the topmost surface was mainly attributed to the reduced grain size. The equiaxed nano-sized grains were in random orientation and the most of their boundaries were low-angle grain boundaries （LAGBs）. The coarse grains are refined into the few micro-sized grains by dislocation activities;deformation twinning was found to be the primary form for the formation of submicron grains;the formation of nanostructure was dominated by dislocation activities accompanied with rotation of grains in local region.
基金Project(2014CB644003)supported by the National Basic Research Program of ChinaProject(51321003)supported by the National Natural Science Foundation of ChinaProject(B06025)supported by"111"Project of China
文摘Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.
基金Project(S2012010010417)supported by the Guangdong Natural Science Foundation,ChinaProject(20130172110008)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘A facile route for preparation of gradient wettability surface on copper substrate with contact angle changing from 90.3°to4.2°was developed.The Cu（OH）2 nanoribbon arrays were electrochemically deposited on copper foil via a modified anodization technology,and the growth degree and density of the Cu（OH）2 arrays may be controlled varying with position along the substrate by slowly adding aqueous solution of KOH into the two-electrode cell of an anodization system to form the gradient surface.The prepared surface was water resistant and thermal stable,which could keep its gradient wetting property after being immersed in water bath at 100℃ for 10 h.The results of scanning electron microscopy（SEM）,X-ray diffraction（XRD） and X-ray photoelectron spectroscopy（XPS） demonstrate that the distribution of Cu（OH）2 nanoribbon arrays on copper surface are responsible for the gradient wettability.
基金supported financially by the National Natural Science Foundation of China(No.51771155)the Equipment Pre-research Field Foundation(No.61409220202).
文摘In this work,ultrasonic surface rolling process(USRP)was utilized to produce a gradient structured layer on 7 B50-T7751 aluminum alloy,and the mechanical properties and corrosion fatigue behavior of treated samples were studied.These results reveal that underwent USRP,a 425~m thick gradient structure and a 700~m deep compressive residual stress field are created,aluminum grain size become fine(~67 nm),and the corrosion rate of treated surface reduces by 60.08%owing to the combined effect of compressive residual stress and surface nanocrystallization.The corrosion fatigue strength is enhanced to 117%of that of 7 B50 Al alloys by means of USRP due to the introduced compressive residual stress,which is considered as the major favorable factor in suppressing the initiation and early propagation of corrosion fatigue cracks.Besides,the gradient structure is an important factor in providing a significant synergistic contribution to the improvement of corrosion fatigue performance.
基金Project supported by the National Natural Science Foundation of China(Nos.11872233 and11472163)the China Scholarship Council(No.201706890041)the Innovation Program of Shanghai Municipal Education Commission(No.2017-01-07-00-09-E00019)
文摘In this pap er, a novel size-dep endent functionally graded (FG) cylindrical shell model is develop ed based on the nonlocal strain gradient theory in conjunction with the Gurtin-Murdoch surface elasticity theory . The new model containing a nonlocal parameter, a material length scale parameter, and several surface elastic constants can capture three typical typ es of size e ects simultaneously , which are the nonlocal stress ef- fect, the strain gradient e ect, and the surface energy e ects. With the help of Hamilton’s principle and rst-order shear deformation theory , the non-classical governing equations and related b oundary conditions are derived. By using the prop osed model, the free vibra- tion problem of FG cylindrical nanoshells with material prop erties varying continuously through the thickness according to a p ower-law distribution is analytically solved, and the closed-form solutions for natural frequencies under various b oundary conditions are obtained. After verifying the reliability of the prop osed model and analytical method by comparing the degenerated results with those available in the literature, the in uences of nonlocal parameter, material length scale parameter, p ower-law index, radius-to-thickness ratio, length-to-radius ratio, and surface e ects on the vibration characteristic of func- tionally graded cylindrical nanoshells are examined in detail.
基金Financial supports from the National Key Research and Development Program of China (No. 2017YFA0204401)Shenyang National Laboratory for Materials Science (No. 2015RP04)
文摘Nanolaminated structures composed of low-angle grain boundaries(LAGBs) possess high thermal stability. In this paper, a gradient nanolaminated(GNL) surface layer with smooth finish was fabricated on an interstitial-free steel by means of surface mechanical rolling treatment. Microstructural observations demonstrated that the average lamellar thickness is about 80 nm in the topmost surface layer and increases with increasing depth. High thermal stability was confirmed in the GNL surface layer after annealing at 500℃. Diffusion measurements showed that effective diffusivity of Cr in GNL layer is 4–6 orders of magnitude higher than lattice diffusivity within the temperature range from 400 to 500℃. This might be attributed to numerous LAGBs or dislocation structures with a higher energy state in the GNL surface layer. This work demonstrates the possibility to advanced chromizing(or other surface alloying)processes of steels with formation of GNL surface layer, so that a thicker alloyed surface layer with a stable nanostructure is achieved.
基金supported financially by the National Key Research and Development Program of China (No.2017YFA0204400)Shenyang National Laboratory for Materials Science(No. 2015RP04)
文摘In the present work, an ultrahigh strength bearing steel（AISI 52100） was subjected to surface mechanical rolling treatment（SMRT） at room temperature. Microstructural observations showed that martensitic laths, twins and cementite particles in the initial microstructure underwent distinct plastic strains and were gradually refined into nanostructures. Consequently, a gradient nanostructured（GNS） surface layer with a mean grain size of -24 nm at the top surface was obtained on the bearing steel, resulting in an increment of -20% in the surface hardness. Analyses based on microstructural evolution, phase constitution and in-depth hardness distribution revealed a mechanically induced formation mechanism of the GNS surface layer. The multiple surface severe plastic deformation under fine lubrication and cooling during SMRT contributed to the formation of a thick hardened surface layer on the bearing steel.
基金financially supported by the National Key Research and Development Plan(No.2017YFB1103700)the Natural Science Foundation of China(Nos.51671101 and51464034)+1 种基金the Natural Science foundation of Jiangxi Province(Nos.20172BCB22002,20171BCD40003,20161ACB21003,20162BCB23013)the Science and Technology Key Research Plan in Jiangxi Educational Department(No.GJJ150010)
文摘Nanocrystalline surface layers and gradient nanostructure in 5182 aluminum alloy have been produced through surface mechanical attrition treatment(SMAT). The results indicate that the gradient nanostructure can not only improve the mechanical properties of 5182 Al alloy, but also has a certain effect on the Portevin-Le Chatelier(PLC) effect. The yield and ultimate tensile strength of 5182 Al alloy with SMAT are significantly improved combining with the decrease of fracture elongation compared with the as-received one. The PLC effect of 5182 Al alloy could be effectively postponed by the formation of gradient nanostructure after SMAT. It leads to the increase of critical strain of the PLC effect, more concentrated distribution of serrated strain, and increase of average stress amplitude in special strain range. The influence of grain size and gradient nanostructure on the PLC effect of 5182 Al alloy was also discussed in detail. Grain refinement could sharply increase the density of dislocations and hinder the movement of dislocations, which results in the decrease of moving speed of dislocations and the more concentrated distribution of solute atoms. The solute atoms would aggregate to form nano precipitates and further impede movement of dislocation. The stronger interaction between the dislocations and the nano precipitates is the main mechanism of postponed PLC effect.
基金financially supported by National Natural Science Foundation of China(Nos.20775070. J0830413)Zhejiang Provincial Natural Science Foundation of China(No.R4080124)
文摘The separation optimization of nine organic and inorganic anions in tobacco leaves using gradient ion chromatography by response surface methodology was investigated.In order to achieve this goal the usefulness of the chromatographic response function（CRF） for the evaluation of the two different chromatographic performance goals（resolution and analysis time） was tested. The experiments were performed according to a Box-Behnken design response surface experimental design.
基金supported by the National Natural Science Foundation of China(Grant No.50001008)the China Postdoctoral Science Foundation.
文摘Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.
基金supported by the National Natural Science Foundation of China(No.52071038).QYH acknowledges funding from the Natural Science Foundation of Chongqing(grant cstc2021jcyj-msxmX1185).
文摘The microstructure,hardness and tensile properties have been studied in copper processed by high pressure surface rolling(HPSR)both in the as-deformed condition and after subsequent annealing at 150℃.It is found that a gradient structure with significant differences in the scale of microstructural features is formed by HPSR.The deformed microstructure varies from nano-and ultrafine-scale structures with a large fraction of high angle boundaries near the surface to lightly deformed grains at depths of 1-3 mm below the surface.Tensile tests of 1-mm-thick specimens demonstrate that the asdeformed material has a high strength and a low uniform elongation.Annealing at 150℃results in partial recrystallization,which creates new through-thickness gradients.Except for the topmost layer and several bands in the adjacent layer,recrystallization is more pronounced close to the surface.The fraction recrystallized is at least 80%at depths of 60-300μm after annealing for 960 min.The fraction recrystallized in the subsurface decreases with increasing depth,and the deformed layer at depths greater than 500μm re-mains largely non-recrystallized after annealing.This partially recrystallized condition demonstrates an improved combination of strength and ductility.
基金supported by National Natural Science Foundation of China(No.51777076)the Self-topic Fund of State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources(No.LAPS2019-21)。
文摘In this paper,plasma fluorination is combined with plasma silicon deposition to achieve step gradient modification on an epoxy resin surface.The physicochemical characteristics of samples are investigated and the electrical performances measured.The obtained results show that compared with untreated and single treated samples,the samples treated by step gradient modification significantly improve the flashover performance.According to experiment and simulation,the mechanism explanations are summarized as follows.First,it is found that the step gradient conductivity can effectively optimize the electric field distribution of a needle-needle electrode.Then,step gradient modification suppresses the accumulation of surface charge at the triple junction and makes the charge distribution more uniform.Furthermore,it can accelerate the surface dissipation on a high electrical field region and control the dissipation rate on a low electrical field region.All these results can restrain surface discharge and increase the flashover voltage.The step gradient modification method proposed in this paper provides a new idea for improving the surface insulation performance.
基金supported by the joint Ph D project between the Hong Kong Polytechnic University and Southern University of Science and Technologythe grant from the Research Committee of Poly U under student account code RK2N+1 种基金supported by the National Natural Science Foundation of China Projects (Nos. 51701171 and 51971187)the Fundamental Research Program of Shenzhen (Grant No. JCYJ20170412153039309)。
文摘Heterogeneous gradient nanostructured metals have been shown to achieve the strength-ductility synergy, thus potentially possessing the enhanced tribological performance in comparison with their homogeneous nanograined counterparts. In this work, a facile laser surface remelting-based surface treatment technique is developed to fabricate a gradient nanostructured layer on a TiZrHfTaNb refractory highentropy alloy. The characterization of the microstructural evolution along the depth direction from the matrix to the topmost surface layer shows that the average grain size in the ~100 μm-thick gradient nanostructured layer is dramatically refined from the original ~200 μm to only ~8 nm in the top surface layer. The microhardness is therefore gradually increased from ~240 HV in matrix to ~650 HV in the topmost surface layer, approximately 2.7 times. Noticeably, the original coarse-grained single-phase bodycentered-cubic TiZrHfTaNb refractory high-entropy alloy is gradually decomposed into TiNb-rich bodycentered-cubic phase, TaNb-rich body-centered-cubic phase, ZrHf-rich hexagonal-close-packed phase and TiZr Hf-rich face-centered-cubic phase with gradient distribution in grain size along the depth direction during the gradient refinement process. As a result, the novel laser surface treatment-introduced gradient nanostructured TiZrHfTaNb refractory high-entropy alloy demonstrates the significantly improved wear resistance, with the wear rate reducing markedly by an order of magnitude, as compared with the as-cast one. The decomposed multi-phases and gradient nanostructures should account for the enhanced wear resistance. Our findings provide new insights into the refinement mechanisms of the laser-treated refractory high-entropy alloys and broaden their potential applications via heterogeneous gradient nanostructure engineering.
基金financially support by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China (No.2011BAE23B02)the Fundamental Research Funds for the Central Universities of China (No.FRF-TP-10-002B)
文摘Copper foils with gradient structure in thickness direction and different roughnesses on two surfaces were fabricated by double rolling. The two surface morphologies of double-rolled copper foils are quite different, and the surface roughness values are 61 and 1095 nm, respectively. The roughness value of matt surface can meet the requirement for bonding the resin matrix with copper foils used for flexible printed circuit boards, thus may omit traditional roughening treatment; the microstructure of double-rolled copper foils demonstrates an obviously asymmetric gradient feature. From bright surface to matt surface in thickness direction, the average grain size first increases from 2.3 to 7.4 μm and then decreases to 3.6 μm; compared with conventional rolled copper foils, the double-rolled copper foils exhibit a remarkably increased bending fatigue life, and the increased range is about 16.2%.
基金supported by the National Special Plan for the 13th Five-Year Plan of China(No.2017YFC0602204-10)Independent Exploration of the Innovation Project for Graduate Students at Central South University(No.2017zzts176)+3 种基金National Natural Science Foundation of China(Nos.41574127,41404106,and 41674075)Postdoctoral Fund Projects of China(No.2017M622608)National Key R&D Program of China(No.2018YFC0603602)Natural Science Youth Fund Project of the Hunan Province,China(No.2018JJ3642)
文摘Magnetic field gradient tensor technique provides abundant data for delicate inversion of subsurface magnetic susceptibility distribution. Large scale magnetic data inversion imaging requires high speed and accuracy for forward modeling. For arbitrarily distributed susceptibility data on an undulated surface, we propose a fast 3D forward modeling method in the wavenumber domain based on(1) the wavenumber-domain expression of the prism combination model and the Gauss–FFT algorithm and(2) cubic spline interpolation. We apply the proposed 3D forward modeling method to synthetic data and use weighting coefficients in the wavenumber domain to improve the modeling for multiple observation surfaces, and also demonstrate the accuracy and efficiency of the proposed method.
基金the National Key Research and Development Program of China(Nos.2017YFA0204401 and 2017YFA0204403)the Liaoning Revitalization Talents Program(No.XLYC1808008)the Shenyang National Laboratory for Materials Science。
文摘Welded joints are usually characterized by microstructural and compositional inhomogeneities, which may significantly degrade their fatigue properties and result in unpredictable failures. The present work demonstrates a novel and simple method to effectively optimize the microstructure in the surface layer and promote the fatigue properties of welded specimens. By a recently developed approach—surface mechanical rolling treatment(SMRT), a gradient nanostructured surface layer is formed on welded S355 J2 W steel specimens. The mean grain size is refined to nanometer scale, and the hardness is significantly enhanced in the SMRT surface layer. Independent of the initially inhomogeneous microstructure and hardness distributions, the microstructure and hardness distributions in the surface layers are comparable on different zones of a welded specimen after SMRT with the same procedure. Consequently, fatigue property of the SMRT specimens is significantly enhanced relative to that of the as-welded specimens within the high cycle fatigue regime.
基金supported by the National Natural Science Foundation of China (Grant Nos. 11074104 and 10604045)the Higher Education Science and Technology Program of Shandong Province, China (Grant No. J09LA02)the University Student's Science and Technology Innovation Fund of Ludong University, China (Grant No. 10g003)
文摘Based on closed-orbit theory, the photodetachment of H- in a gradient electric field near a metal surface is studied. It is demonstrated that the gradient electric field has a significant influence on the photodetachment of negative ions near a metal surface. With the increase of the gradient of the electric field, the oscillation in the photodetachment cross section becomes strengthened. Besides, in contrast to the photodetachment of H- near a metal surface in a uniform electric field, the oscillating amplitude and the oscillating region in the cross section of a gradient electric field also become enlarged. Therefore, we can use the gradient electric field to control the photodetachment of negative ions near a metal surface. We hope that our results will be useful for understanding the photodetachment of negative ions in the vicinity of surfaces, cavities, and ion traps.
基金supported by the National Natural Science Foundation of China(22075170,52072233)the Beijing National Laboratory for Condensed Matter Physics。
文摘Layered LiCoO_(2)(LCO)acts as a dominant cathode material for lithium-ion batteries(LIBs)in 3C products because of its high compacted density and volumetric energy density.Although improving the high cutoff voltage is an effective strategy to increase its capacity,such behavior would trigger rapid capacity decay due to the surface or/and structure degradation.Herein,we propose a bi-functional surface strategy involving constructing a robust spinel-like phase coating layer with great integrity and compatibility to LiCoO_(2) and modulating crystal lattice by anion and cation gradient co-doping at the subsurface.As a result,the modified LiCoO_(2)(AFM-LCO)shows a capacity retention of 80.9%after 500 cycles between 3.0and 4.6 V.The Al,F,Mg enriched spinel-like phase coating layer serves as a robust physical barrier to effectively inhibit the undesired side reactions between the electrolyte and the cathode.Meanwhile,the Al,F,Mg gradient co-doping significantly enhances the surficial structure stability,suppresses Co dissolution and oxygen release,providing a stable path for Li-ions mobility all through the long-term cycles.Thus,the surface bi-functional strategy is an effective method to synergistically improve the electrochemical performances of LCO at a high cut-off voltage of 4.6 V.
