In order to enhance the off-peak performance of gas turbine combined cycle(GTCC)units,a novel collaborative power generation system(CPG)was proposed.During off-peak operation periods,the remaining power of the GTCC wa...In order to enhance the off-peak performance of gas turbine combined cycle(GTCC)units,a novel collaborative power generation system(CPG)was proposed.During off-peak operation periods,the remaining power of the GTCC was used to drive the adiabatic compressed air energy storage(ACAES),while the intake air of the GTCC was heated by the compression heat of theACAES.Based on a 67.3MW GTCC,under specific demand load distribution,a CPG system and a benchmark system(BS)were designed,both of which used 9.388% of the GTCC output power to drive the ACAES.The performance of the CPG and the BS without intake air heating was compared.The results show that the load rate of the GTCC in the CPG system during off-peak periods is significantly enhanced,and the average operating efficiency of the GTCC is increased by 1.19 percentage points.However,in the BS system,due to the single collaborativemethod of load shifting,the GTCC operative efficiency is almost increased by 1.00 percentage points under different ambient temperatures.In a roundtrip cycle at an ambient temperature of 288.15K,the systemefficiency of the CPG reaches 0.5010,which is 0.62 percentage points higher than the operative efficiency of 0.4948 in the standalone GTCC;while the system efficiency of the BS is slightly inferior to that of the standalone GTCC.The findings confirm the technical feasibility and performance improvement of the ACAES-GTCC collaborative power generation system.展开更多
Hydraulic stimulation technology is widely employed to enhance the permeability of geothermal reservoirs.Nevertheless,accurately predicting hydraulic fracture propagation in complex geological conditions remains chall...Hydraulic stimulation technology is widely employed to enhance the permeability of geothermal reservoirs.Nevertheless,accurately predicting hydraulic fracture propagation in complex geological conditions remains challenging,thereby hindering the effective utilization of existing natural fractures.In this study,a phase field model was developed utilizing the finite element method to examine the influence of fluid presence,stress conditions,and natural fractures on the initiation and propagation of hydraulic fractures.The model employs Biot's poroelasticity theory to establish the coupling between the displacement field and the fluid field,while the phase field theory is applied to simulate fracture behavior.The results show that whenσ_(x0)/σ_(y0)<3 or qf<20 kg/(m^(3)·s),the presence of natural fractures can alter the original propagation direction of hydraulic fractures.Conversely,in the absence of these conditions,the propagation path of natural fractures is predominantly influenced by the initial stress field.Furthermore,based on the analysis of breakdown pressure and damage area,the optimal intersection angle between natural fractures and hydraulic fractures is determined to range from 45°to 60°.Finally,once a dominant channel forms,initiating and propagating hydraulic fractures in other directions becomes increasingly difficult,even in highly fractured areas.This method tackles the challenges of initiating and propagating hydraulic fractures in complex geological conditions,providing a theoretical basis for optimizing Enhanced Geothermal System(EGS)projects.展开更多
Power quality is a crucial area of research in contemporary power systems,particularly given the rapid proliferation of intermittent renewable energy sources such as wind power.This study investigated the relationship...Power quality is a crucial area of research in contemporary power systems,particularly given the rapid proliferation of intermittent renewable energy sources such as wind power.This study investigated the relationships between power quality indices of system output and PSD by utilizing theories related to spectra,PSD,and random signal power spectra.The relationship was derived,validated through experiments and simulations,and subsequently applied to multi-objective optimization.Various optimization algorithms were compared to achieve optimal system power quality.The findings revealed that the relationships between power quality indices and PSD were influenced by variations in the order of the power spectral estimation model.An increase in the order of the AR model resulted in a 36%improvement in the number of optimal solutions.Regarding optimal solution distribution,NSGA-II demonstrated superior diversity,while MOEA/D exhibited better convergence.However,practical applications showed that while MOEA/D had higher convergence,NSGA-II produced superior optimal solutions,achieving the best power quality indices(THDi at 4.62%,d%at 3.51%,and cosφat 96%).These results suggest that the proposed method holds significant potential for optimizing power quality in practical applications.展开更多
To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a b...To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.展开更多
To promote energy conservation,emission reduction,and sustainable development in thermal power enterprises,this study conducted a detailed analysis of the problems existing in measurement management in these enterpris...To promote energy conservation,emission reduction,and sustainable development in thermal power enterprises,this study conducted a detailed analysis of the problems existing in measurement management in these enterprises and explored targeted solutions.The analysis found that,faced with increasingly stringent environmental protection requirements and urgent needs to improve energy efficiency,thermal power enterprises must address the current issues in energy measurement management.They should actively respond to the national call for energy conservation and emission reduction,continuously optimize energy measurement management processes,improve energy utilization efficiency,reduce unnecessary energy consumption and emissions,and lay a solid foundation for the green transformation and sustainable development of the industry.展开更多
In this study,the power generation difference between the east-west and the north-south orientation of the vertically installed heterojunction solar cell(HJT)modules was deeply discussed.East-west oriented HJT module ...In this study,the power generation difference between the east-west and the north-south orientation of the vertically installed heterojunction solar cell(HJT)modules was deeply discussed.East-west oriented HJT module has 30%higher power generation,especially in desert photovoltaic(PV)with a bimodal distribution.While the south-north one has a single peak,the same as normal PV modules.Vertical power generation technology of HJT also has less land occupation,which is of great significance for optimizing the design of photovoltaic systems.展开更多
With the proposed carbon-neutrality targets,intermittent renewable energy will become increasingly significant for the power sector in the future.It is vital to study its development paths,particularly for wind power ...With the proposed carbon-neutrality targets,intermittent renewable energy will become increasingly significant for the power sector in the future.It is vital to study its development paths,particularly for wind power and photovoltaics,while considering constraints on diffusion potential.Using learning curves,dynamic programming,and Bass models,this study analyzes technological diffusion trends to determine the most cost-effective development route for intermittent renewable energy power generation in China by 2060.This study simplifies reality by examining the individual diffusion processes of wind and photovoltaic power,focusing on the self-diffusion characteristics of the two technologies.The study assumes that self-diffusion is the primary driver of future development and describe the influence of multiple factors.The study finds that supportive policies are key drivers of development in the early stages of intermittent renewable energy deployment,especially for photovoltaics.The current diffusion scale of photovoltaics has a greater positive impact on its future development than that of wind power due to lower costs.In the long term,the phased goal for 2030 is projected to be met ahead of schedule,and the majority of future intermittent renewable energy output is expected to come from photovoltaics.The rapid development phases of photovoltaic and wind power conclude at similar times,but the maximum diffusion potential of photovoltaics is higher than that of wind power.Investment constraints and technological levels affect the initial and middle phases of the development path,but their effects are limited.The capacity of the power grid remains the key constraint in the entire research field.展开更多
The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more...The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more fluctuations of system inertia.To address this issue,a novel equivalent inertia evaluation method for multiple PV power generation under virtual inertia control is proposed.The total system inertia is first estimated based on historical or injected disturbance.Then,the total inertia of multiple PV power generation is directly calculated by subtracting the inertia of synchronous generators from the estimated system inertia.To improve practicality,a partition-based strategy is introduced,which divides the system into regions characterized by homogeneous frequency response behaviors.After partitioning,only the synchronous generator data within the region and inter-area transmission line power are required for evaluation,reducing the demand for PMU data compared to traditional methods requiring measurements at each PV connection point.Comprehensive simulation results in a 10-machine 39-bus system penetrated with multiple PV power generation validated the effectiveness of the proposed method.展开更多
In the original publication,mistakenly first and corresponding affiliation is given as:Thermoelectricity Technology Center,Hangzhou Dahe Thermo-Magnetics Co.Ltd,Hangzhou 310053,ChinaThe correct first and corresponding...In the original publication,mistakenly first and corresponding affiliation is given as:Thermoelectricity Technology Center,Hangzhou Dahe Thermo-Magnetics Co.Ltd,Hangzhou 310053,ChinaThe correct first and corresponding affiliation is:State Key Laboratory of Silicon Materials,School of Materials Science and Engineering,Zhejiang University,Hangzhou 310027,China.展开更多
This study explores off-grid power generation business models in the Lao People's Democratic Republic(Lao PDR),with the objective of identifying viable pathways to expand energy access in rural and underserved reg...This study explores off-grid power generation business models in the Lao People's Democratic Republic(Lao PDR),with the objective of identifying viable pathways to expand energy access in rural and underserved regions.The research aims to analyze and evaluate various business models in terms of their technical,economic,and social viability within the unique geographic and policy context of Lao PDR.There are two level of the research objectives:High Level Objectives(HLO)and Concreted Research Objectives(CRO).For HLO is that an appropriated off-grid power generation business model for Laos supports the Lao PDR Government’s commitment to promote an inclusive green growth development agenda that ensures lowered GHG emissions and increased energy efficiency.The Lao PDR National Determined Contribution(NDC)to the United Nations Framework Convention on Climate Change(UNFCCC)notes the country’s ambitious plans to lower energy consumption and reduce GHG emissions.While the CRO are focused on learning strategies,regulation and practical lessons from other countries the ASEAN region on the off-grid development and business model.To analyze and investigate the environmental strategy of business model under external and internal context and related and considered factors.And finally,this is to conclude and recommend the off-grid power generation business model as the research conclusion,which will become a support mechanism for the companies to operate consistently over many years into the future according to ambitious goal for supplying modern and save energy for rural families by 2030.展开更多
In the energy industry landscape,thermal power generation stands as a critical energy supply method,and the safety of its construction and operation is paramount.Currently,all stages of the life cycle of construction ...In the energy industry landscape,thermal power generation stands as a critical energy supply method,and the safety of its construction and operation is paramount.Currently,all stages of the life cycle of construction projects have garnered widespread attention.Among these,the infrastructure construction and operation phases of thermal power generation enterprises pose numerous issues worthy of in-depth study in terms of safety production management.This article starts by examining safety production management during these two phases,analyzing characteristics such as management models,legal bases,and responsible entities.It explores the reasons behind these characteristics and elaborates on key management priorities,providing a comprehensive and insightful reference for safety production management in thermal power generation enterprises.展开更多
With the continuous adjustment of the energy structure,photovoltaic(PV)power generation projects are increasing,playing a crucial role in promoting the application of clean energy.However,the current audit of complete...With the continuous adjustment of the energy structure,photovoltaic(PV)power generation projects are increasing,playing a crucial role in promoting the application of clean energy.However,the current audit of completed final accounts for photovoltaic power generation projects faces many challenges,such as incomplete institutional processes,scattered archive management materials,inadequate digital intelligence systems,and insufficient analysis of final account amounts.Based on this,this article aims to deeply analyze these issues and propose targeted audit suggestions to standardize the construction and audit work of photovoltaic power generation projects and promote the sustainable and healthy development of the photovoltaic power generation business.展开更多
This study investigates the Maximum Power Point Tracking(MPPT)control method of offshore windphotovoltaic hybrid power generation system with offshore crane-assisted.A new algorithm of Global Fast Integral Sliding Mod...This study investigates the Maximum Power Point Tracking(MPPT)control method of offshore windphotovoltaic hybrid power generation system with offshore crane-assisted.A new algorithm of Global Fast Integral Sliding Mode Control(GFISMC)is proposed based on the tip speed ratio method and sliding mode control.The algorithm uses fast integral sliding mode surface and fuzzy fast switching control items to ensure that the offshore wind power generation system can track the maximum power point quickly and with low jitter.An offshore wind power generation system model is presented to verify the algorithm effect.An offshore off-grid wind-solar hybrid power generation systemis built in MATLAB/Simulink.Compared with other MPPT algorithms,this study has specific quantitative improvements in terms of convergence speed,tracking accuracy or computational efficiency.Finally,the improved algorithm is further analyzed and carried out by using Yuankuan Energy’s ModelingTech semi-physical simulation platform.The results verify the feasibility and effectiveness of the improved algorithm in the offshore wind-solar hybrid power generation system.展开更多
This paper discusses the potential and prospect of building-integrated photovoltaics (BIPV) for solar electrical power generation in China.The BIPV technology has been identified as the most economical renewable energ...This paper discusses the potential and prospect of building-integrated photovoltaics (BIPV) for solar electrical power generation in China.The BIPV technology has been identified as the most economical renewable energy resource to contribute to world electrical energy demand for protecting environment from reduced fossil fuel consumption.The available solar energy resource of 14 cities and the potential power generation from PV claddings in buildings in China were estimated.The economical analysis of BIPV application is discussed.It is found that the potential is significant and the government should play an important role in its development.展开更多
Through a great many qualitative and quantitative analyses, this paperstudies the development of gas power in China in the coming ten years based oninvestigations of more than one year. Some good advices are suggested...Through a great many qualitative and quantitative analyses, this paperstudies the development of gas power in China in the coming ten years based oninvestigations of more than one year. Some good advices are suggested toinvestors and decision-makers, such as the advantages and disadvantages ofpower generation using natural gas, development plans of local power grids, andproblems necessary to be noted and solved.[展开更多
The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao...The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao,North China,and Zhangzhou basins are of special interest due to their considerable exploration depths,extensive development history,and high levels of research activity.This study focuses on the three basins to analyze their thermal reservoir characteristics in eastern China.Between 2017 and 2023,the research team carried out a comprehensive analysis involving deep boreholes that exceeded 4000 m in depth within these three basins.They meticulously created detailed physical profiles that captured essential characteristics such as porosity,permeability,and thermal properties,reaching down to the basement of each basin.The findings indicated that variations in thermal conductivity within shallow geotechnical layers significantly influence the redistribution of deep thermal energy in the upper layers of the earth.Furthermore,differences in physical properties notably affect heat transport processes.The research proposes distinct heat models tailored for each basin:For the Songliao Basin,a low-permeability model with homogeneous thermal properties is constructed;for the North China Basin,high permeability and thermal conductivity layers are highlighted;and a fracture network controlling water and heat is presented in the Zhangzhou Basin.To elucidate the thermal structure of these basins,the Curie surface and Moho surface were analyzed.The shallow Curie surface indicates ongoing intense thermal activity stemming from crustal heat sources,while a shallow Moho surface signifies historical vigorous mantle thermal activity associated with mantle source heat production.Furthermore,the research evaluates the geothermal resources and the potential for carbon emission reduction in these basins.Total volume of exploitable geothermal fluid is estimated to be 76.9×10^(9) m^(3)/a,corresponding to an annual renewable geothermal energy 1.47×10^(16)k J.The implementation of geothermal energy could lead to a reduction in annual CO_(2)emissions by nearly 2×10^(9) t,which constitutes about 17.4%of China’s national carbon emissions in 2022.This estimation provides invaluable theoretical insights and data support for geothermal exploration and sustainable development in eastern China.展开更多
The available heat content (stored heat energy) of hot dry rock (HDR) at a depth of 1–10 km in the global land crust is estimated to be 5.06×10~8 EJ,attracting considerable global attention.This paper presents a...The available heat content (stored heat energy) of hot dry rock (HDR) at a depth of 1–10 km in the global land crust is estimated to be 5.06×10~8 EJ,attracting considerable global attention.This paper presents a comprehensive analysis of the geological framework,HDR resource potential,exploration advancements,and the development of enhanced geothermal systems (EGSs) in China.HDR resources are extensively distributed across China.Within the depth range of 3–10 km,China’s estimated potential approximates2.29×10~7 EJ,with a theoretical power generation capacity of approximately 1.67×10^(16) k Wh.Replacing coal power with HDR can help to achieve a net emission reduction of 1.34×10^(16) kg CO_(2) (approximately1.34×10^(13) t),representing an emission reduction efficiency of 94.4%.Based on a development cycle of100 years,the average annual emission reduction reaches 1.34×10^(10) t CO_(2),equivalent to 117%of China’s annual carbon emissions in 2022.Furthermore,in the context of global warming,the development and utilization of HDR,which is feasible in virtually any region worldwide,offers significant potential to support global carbon reduction efforts.China has made substantial progress in HDR exploration in recent years.This paper systematically classifies China’s HDR resources into four genetic types—highly radioactive heat-producing,sedimentary basin,active volcanic,and intensely tectonic zones—and offers detailed exploration insights for each category.Each classification exhibits distinct geological and tectonic characteristics that influence heat source mechanisms and resource distribution.Furthermore,this paper documents significant advances in EGS construction,particularly in the Gonghe Basin on the northeastern margin of the Qianghai-Xizang Plateau and the Matouying uplift in the North China Basin,where successful reservoir stimulation,microseismic monitoring,and experimental power generation have been achieved.Despite these developments,challenges persist,including technical adaptability under complex geological conditions and the economic viability of large-scale HDR development.This paper suggests that future initiatives should emphasize resource exploration,technological research,and policy support to foster sustainable HDR resource development in China,thereby contributing to the global energy transition and environmental sustainability.展开更多
This paper presents a new power generation structure that can provide DC energy for passive UHF RFID with high sensitivity and high efficiency. The structure is designed with 0.18μm standard CMOS technology, includin...This paper presents a new power generation structure that can provide DC energy for passive UHF RFID with high sensitivity and high efficiency. The structure is designed with 0.18μm standard CMOS technology, including two charge pumps,a current reference, and a group of bias circuits. Low-voltage performance is improved thanks to the bias structure,which eliminates the threshold voltage drop and body-effect of conventional circuits. A 350mV minimum input level is required to generate a 1.5V power supply for a 100k~ load with power conversion efficiency （PCE） of 22%. PCE up to 29.8% is achieved with a 60kΩ load. Simulation results show that the new circuit is superior to conventional charge pumps.展开更多
Lignocellulosic biomass has attracted great interest in recent years for energy production due to its renewability and carbon-neutral nature.There are various ways to convert lignocellulose to gaseous,liquid and solid...Lignocellulosic biomass has attracted great interest in recent years for energy production due to its renewability and carbon-neutral nature.There are various ways to convert lignocellulose to gaseous,liquid and solid fuels via thermochemical,chemical or biological approaches.Typical biomass derived fuels include syngas,bio-gas,bio-oil,bioethanol and biochar,all of which could be used as fuels for furnace,engine,turbine or fuel cells.Direct biomass fuel cells mediated by various electron carriers provide a new direction of lignocellulose conversion.Various metal and non-metal based carriers have been screened for mediating the electron transfer from biomass to oxygen thus generating electricity.The power density of direct biomass fuel cells can be over 100 mW cm^(-2),which shows promise for practical applications.Lignocellulose and its isolated components,primarily cellulose and lignin,have also been paid considerable attention as sustainable carbonaceous materials for preparation of electrodes for supercapacitors,lithium-ion batteries and lithium-sulfur batteries.In this paper,we have provided a state-of-the-art review on the research progress of lignocellulosic biomass as feedstock and materials for power generation and energy storage focusing on the chemistry aspects of the processes.It was recommended that process integration should be performed to reduce the cost for thermochemical and biological conversion of lignocellulose to biofuels,while efforts should be made to increase efficiency and improve the properties for biomass fuelled fuel cells and biomass derived electrodes for energy storage.展开更多
This paper presents a preliminary experimental investigation on magnetohydrodynamic （MHD） power generation using seeded supersonic argon flow as working fluid. Helium and argon are used as driver and driven gas resp...This paper presents a preliminary experimental investigation on magnetohydrodynamic （MHD） power generation using seeded supersonic argon flow as working fluid. Helium and argon are used as driver and driven gas respectively in a shock tunnel. Equilibrium contact surface operating mode is used to obtain high temperature gas, and the conductivity is obtained by adding seed K2CO3 powder into the driven section. Under the conditions of nozzle inlet total pressure being 0.32 MPa, total temperature 6 504 K, magnetic field density about 0.5 T and nozzle outlet velocity 1 959 m/s, induction voltage and short-circuit current of the segmentation MHD power generation channel are measured, and the experimental results agree with theoretical calculations; the average conductivity is about 20 S/m calculated from characteristics of voltage and current. When load factor is 0.5, the maximum power density of the MHD power generation channel reaches 4.797 1 MW/m3, and the maximum enthalpy extraction rate is 0.34%. Finally, the principle and method of indirect testing for gas state parameters are derived and analyzed.展开更多
文摘In order to enhance the off-peak performance of gas turbine combined cycle(GTCC)units,a novel collaborative power generation system(CPG)was proposed.During off-peak operation periods,the remaining power of the GTCC was used to drive the adiabatic compressed air energy storage(ACAES),while the intake air of the GTCC was heated by the compression heat of theACAES.Based on a 67.3MW GTCC,under specific demand load distribution,a CPG system and a benchmark system(BS)were designed,both of which used 9.388% of the GTCC output power to drive the ACAES.The performance of the CPG and the BS without intake air heating was compared.The results show that the load rate of the GTCC in the CPG system during off-peak periods is significantly enhanced,and the average operating efficiency of the GTCC is increased by 1.19 percentage points.However,in the BS system,due to the single collaborativemethod of load shifting,the GTCC operative efficiency is almost increased by 1.00 percentage points under different ambient temperatures.In a roundtrip cycle at an ambient temperature of 288.15K,the systemefficiency of the CPG reaches 0.5010,which is 0.62 percentage points higher than the operative efficiency of 0.4948 in the standalone GTCC;while the system efficiency of the BS is slightly inferior to that of the standalone GTCC.The findings confirm the technical feasibility and performance improvement of the ACAES-GTCC collaborative power generation system.
基金supported by the National Key Research and Development Program(2021YFB150740401)National Natural Science Foundation of China(42202336)the CAS Pioneer Hundred Talents Program in China(Y826031C01)。
文摘Hydraulic stimulation technology is widely employed to enhance the permeability of geothermal reservoirs.Nevertheless,accurately predicting hydraulic fracture propagation in complex geological conditions remains challenging,thereby hindering the effective utilization of existing natural fractures.In this study,a phase field model was developed utilizing the finite element method to examine the influence of fluid presence,stress conditions,and natural fractures on the initiation and propagation of hydraulic fractures.The model employs Biot's poroelasticity theory to establish the coupling between the displacement field and the fluid field,while the phase field theory is applied to simulate fracture behavior.The results show that whenσ_(x0)/σ_(y0)<3 or qf<20 kg/(m^(3)·s),the presence of natural fractures can alter the original propagation direction of hydraulic fractures.Conversely,in the absence of these conditions,the propagation path of natural fractures is predominantly influenced by the initial stress field.Furthermore,based on the analysis of breakdown pressure and damage area,the optimal intersection angle between natural fractures and hydraulic fractures is determined to range from 45°to 60°.Finally,once a dominant channel forms,initiating and propagating hydraulic fractures in other directions becomes increasingly difficult,even in highly fractured areas.This method tackles the challenges of initiating and propagating hydraulic fractures in complex geological conditions,providing a theoretical basis for optimizing Enhanced Geothermal System(EGS)projects.
基金funded by the Inner Mongolia Nature Foundation Project,Project number:2023JQ04.
文摘Power quality is a crucial area of research in contemporary power systems,particularly given the rapid proliferation of intermittent renewable energy sources such as wind power.This study investigated the relationships between power quality indices of system output and PSD by utilizing theories related to spectra,PSD,and random signal power spectra.The relationship was derived,validated through experiments and simulations,and subsequently applied to multi-objective optimization.Various optimization algorithms were compared to achieve optimal system power quality.The findings revealed that the relationships between power quality indices and PSD were influenced by variations in the order of the power spectral estimation model.An increase in the order of the AR model resulted in a 36%improvement in the number of optimal solutions.Regarding optimal solution distribution,NSGA-II demonstrated superior diversity,while MOEA/D exhibited better convergence.However,practical applications showed that while MOEA/D had higher convergence,NSGA-II produced superior optimal solutions,achieving the best power quality indices(THDi at 4.62%,d%at 3.51%,and cosφat 96%).These results suggest that the proposed method holds significant potential for optimizing power quality in practical applications.
文摘To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.
文摘To promote energy conservation,emission reduction,and sustainable development in thermal power enterprises,this study conducted a detailed analysis of the problems existing in measurement management in these enterprises and explored targeted solutions.The analysis found that,faced with increasingly stringent environmental protection requirements and urgent needs to improve energy efficiency,thermal power enterprises must address the current issues in energy measurement management.They should actively respond to the national call for energy conservation and emission reduction,continuously optimize energy measurement management processes,improve energy utilization efficiency,reduce unnecessary energy consumption and emissions,and lay a solid foundation for the green transformation and sustainable development of the industry.
文摘In this study,the power generation difference between the east-west and the north-south orientation of the vertically installed heterojunction solar cell(HJT)modules was deeply discussed.East-west oriented HJT module has 30%higher power generation,especially in desert photovoltaic(PV)with a bimodal distribution.While the south-north one has a single peak,the same as normal PV modules.Vertical power generation technology of HJT also has less land occupation,which is of great significance for optimizing the design of photovoltaic systems.
基金support from the National Natural Science Foundation of China[Grant No.71874121,No.71671121 and No.71431005]the support from the National Key R&D Programme of China[Grant No.2018YFC0704400]+1 种基金the support from Major Projects of the National Social Science Fund of China[Grant No.17ZDA065]the support from the General Project of the Humanities and Social Science Fund of the Chinese Ministry of Education[Grant No.21YJA630023].
文摘With the proposed carbon-neutrality targets,intermittent renewable energy will become increasingly significant for the power sector in the future.It is vital to study its development paths,particularly for wind power and photovoltaics,while considering constraints on diffusion potential.Using learning curves,dynamic programming,and Bass models,this study analyzes technological diffusion trends to determine the most cost-effective development route for intermittent renewable energy power generation in China by 2060.This study simplifies reality by examining the individual diffusion processes of wind and photovoltaic power,focusing on the self-diffusion characteristics of the two technologies.The study assumes that self-diffusion is the primary driver of future development and describe the influence of multiple factors.The study finds that supportive policies are key drivers of development in the early stages of intermittent renewable energy deployment,especially for photovoltaics.The current diffusion scale of photovoltaics has a greater positive impact on its future development than that of wind power due to lower costs.In the long term,the phased goal for 2030 is projected to be met ahead of schedule,and the majority of future intermittent renewable energy output is expected to come from photovoltaics.The rapid development phases of photovoltaic and wind power conclude at similar times,but the maximum diffusion potential of photovoltaics is higher than that of wind power.Investment constraints and technological levels affect the initial and middle phases of the development path,but their effects are limited.The capacity of the power grid remains the key constraint in the entire research field.
基金supported by the science and technology project of State Grid Ningxia Electric Power Co.,Ltd.(5229DK23000C)the project of Ningxia Natural Science Foundation 2024AAC03745(B329DK24000S).
文摘The increasing penetration of PV power generation inevitably leads to the decline of system inertia,posing challenges to frequency stability.To this end,virtual inertia control has been proposed;however,it causes more fluctuations of system inertia.To address this issue,a novel equivalent inertia evaluation method for multiple PV power generation under virtual inertia control is proposed.The total system inertia is first estimated based on historical or injected disturbance.Then,the total inertia of multiple PV power generation is directly calculated by subtracting the inertia of synchronous generators from the estimated system inertia.To improve practicality,a partition-based strategy is introduced,which divides the system into regions characterized by homogeneous frequency response behaviors.After partitioning,only the synchronous generator data within the region and inter-area transmission line power are required for evaluation,reducing the demand for PMU data compared to traditional methods requiring measurements at each PV connection point.Comprehensive simulation results in a 10-machine 39-bus system penetrated with multiple PV power generation validated the effectiveness of the proposed method.
文摘In the original publication,mistakenly first and corresponding affiliation is given as:Thermoelectricity Technology Center,Hangzhou Dahe Thermo-Magnetics Co.Ltd,Hangzhou 310053,ChinaThe correct first and corresponding affiliation is:State Key Laboratory of Silicon Materials,School of Materials Science and Engineering,Zhejiang University,Hangzhou 310027,China.
文摘This study explores off-grid power generation business models in the Lao People's Democratic Republic(Lao PDR),with the objective of identifying viable pathways to expand energy access in rural and underserved regions.The research aims to analyze and evaluate various business models in terms of their technical,economic,and social viability within the unique geographic and policy context of Lao PDR.There are two level of the research objectives:High Level Objectives(HLO)and Concreted Research Objectives(CRO).For HLO is that an appropriated off-grid power generation business model for Laos supports the Lao PDR Government’s commitment to promote an inclusive green growth development agenda that ensures lowered GHG emissions and increased energy efficiency.The Lao PDR National Determined Contribution(NDC)to the United Nations Framework Convention on Climate Change(UNFCCC)notes the country’s ambitious plans to lower energy consumption and reduce GHG emissions.While the CRO are focused on learning strategies,regulation and practical lessons from other countries the ASEAN region on the off-grid development and business model.To analyze and investigate the environmental strategy of business model under external and internal context and related and considered factors.And finally,this is to conclude and recommend the off-grid power generation business model as the research conclusion,which will become a support mechanism for the companies to operate consistently over many years into the future according to ambitious goal for supplying modern and save energy for rural families by 2030.
文摘In the energy industry landscape,thermal power generation stands as a critical energy supply method,and the safety of its construction and operation is paramount.Currently,all stages of the life cycle of construction projects have garnered widespread attention.Among these,the infrastructure construction and operation phases of thermal power generation enterprises pose numerous issues worthy of in-depth study in terms of safety production management.This article starts by examining safety production management during these two phases,analyzing characteristics such as management models,legal bases,and responsible entities.It explores the reasons behind these characteristics and elaborates on key management priorities,providing a comprehensive and insightful reference for safety production management in thermal power generation enterprises.
文摘With the continuous adjustment of the energy structure,photovoltaic(PV)power generation projects are increasing,playing a crucial role in promoting the application of clean energy.However,the current audit of completed final accounts for photovoltaic power generation projects faces many challenges,such as incomplete institutional processes,scattered archive management materials,inadequate digital intelligence systems,and insufficient analysis of final account amounts.Based on this,this article aims to deeply analyze these issues and propose targeted audit suggestions to standardize the construction and audit work of photovoltaic power generation projects and promote the sustainable and healthy development of the photovoltaic power generation business.
基金supported by the 2022 Sanya Science and Technology Innovation Project,China(No.2022KJCX03)the Sanya Science and Education Innovation Park,Wuhan University of Technology,China(Grant No.2022KF0028)the Hainan Provincial Joint Project of Sanya Yazhou Bay Science and Technology City,China(Grant No.2021JJLH0036).
文摘This study investigates the Maximum Power Point Tracking(MPPT)control method of offshore windphotovoltaic hybrid power generation system with offshore crane-assisted.A new algorithm of Global Fast Integral Sliding Mode Control(GFISMC)is proposed based on the tip speed ratio method and sliding mode control.The algorithm uses fast integral sliding mode surface and fuzzy fast switching control items to ensure that the offshore wind power generation system can track the maximum power point quickly and with low jitter.An offshore wind power generation system model is presented to verify the algorithm effect.An offshore off-grid wind-solar hybrid power generation systemis built in MATLAB/Simulink.Compared with other MPPT algorithms,this study has specific quantitative improvements in terms of convergence speed,tracking accuracy or computational efficiency.Finally,the improved algorithm is further analyzed and carried out by using Yuankuan Energy’s ModelingTech semi-physical simulation platform.The results verify the feasibility and effectiveness of the improved algorithm in the offshore wind-solar hybrid power generation system.
文摘This paper discusses the potential and prospect of building-integrated photovoltaics (BIPV) for solar electrical power generation in China.The BIPV technology has been identified as the most economical renewable energy resource to contribute to world electrical energy demand for protecting environment from reduced fossil fuel consumption.The available solar energy resource of 14 cities and the potential power generation from PV claddings in buildings in China were estimated.The economical analysis of BIPV application is discussed.It is found that the potential is significant and the government should play an important role in its development.
文摘Through a great many qualitative and quantitative analyses, this paperstudies the development of gas power in China in the coming ten years based oninvestigations of more than one year. Some good advices are suggested toinvestors and decision-makers, such as the advantages and disadvantages ofpower generation using natural gas, development plans of local power grids, andproblems necessary to be noted and solved.[
基金funded by the Basic Scientific Research of China Geological Academy(YK202305)National Key R&D Program of China(2019YFB1504101)+1 种基金National Natural Science Foundation of China(41602271)China Geological Survey(DD20160207 and DD20189112)。
文摘The geothermal resources in China are primarily found in its sedimentary basins,particularly in the large basins located in eastern China,which hold significant potential for geothermal energy development.The Songliao,North China,and Zhangzhou basins are of special interest due to their considerable exploration depths,extensive development history,and high levels of research activity.This study focuses on the three basins to analyze their thermal reservoir characteristics in eastern China.Between 2017 and 2023,the research team carried out a comprehensive analysis involving deep boreholes that exceeded 4000 m in depth within these three basins.They meticulously created detailed physical profiles that captured essential characteristics such as porosity,permeability,and thermal properties,reaching down to the basement of each basin.The findings indicated that variations in thermal conductivity within shallow geotechnical layers significantly influence the redistribution of deep thermal energy in the upper layers of the earth.Furthermore,differences in physical properties notably affect heat transport processes.The research proposes distinct heat models tailored for each basin:For the Songliao Basin,a low-permeability model with homogeneous thermal properties is constructed;for the North China Basin,high permeability and thermal conductivity layers are highlighted;and a fracture network controlling water and heat is presented in the Zhangzhou Basin.To elucidate the thermal structure of these basins,the Curie surface and Moho surface were analyzed.The shallow Curie surface indicates ongoing intense thermal activity stemming from crustal heat sources,while a shallow Moho surface signifies historical vigorous mantle thermal activity associated with mantle source heat production.Furthermore,the research evaluates the geothermal resources and the potential for carbon emission reduction in these basins.Total volume of exploitable geothermal fluid is estimated to be 76.9×10^(9) m^(3)/a,corresponding to an annual renewable geothermal energy 1.47×10^(16)k J.The implementation of geothermal energy could lead to a reduction in annual CO_(2)emissions by nearly 2×10^(9) t,which constitutes about 17.4%of China’s national carbon emissions in 2022.This estimation provides invaluable theoretical insights and data support for geothermal exploration and sustainable development in eastern China.
基金supported by the National Key Research and Development Program of China (2021YFB1507401)Qinghai Province Clean Energy Minerals Special Project(2022013004qj004)Geological Survey Project of China Geological Survey (DD20221676, DD20230019)。
文摘The available heat content (stored heat energy) of hot dry rock (HDR) at a depth of 1–10 km in the global land crust is estimated to be 5.06×10~8 EJ,attracting considerable global attention.This paper presents a comprehensive analysis of the geological framework,HDR resource potential,exploration advancements,and the development of enhanced geothermal systems (EGSs) in China.HDR resources are extensively distributed across China.Within the depth range of 3–10 km,China’s estimated potential approximates2.29×10~7 EJ,with a theoretical power generation capacity of approximately 1.67×10^(16) k Wh.Replacing coal power with HDR can help to achieve a net emission reduction of 1.34×10^(16) kg CO_(2) (approximately1.34×10^(13) t),representing an emission reduction efficiency of 94.4%.Based on a development cycle of100 years,the average annual emission reduction reaches 1.34×10^(10) t CO_(2),equivalent to 117%of China’s annual carbon emissions in 2022.Furthermore,in the context of global warming,the development and utilization of HDR,which is feasible in virtually any region worldwide,offers significant potential to support global carbon reduction efforts.China has made substantial progress in HDR exploration in recent years.This paper systematically classifies China’s HDR resources into four genetic types—highly radioactive heat-producing,sedimentary basin,active volcanic,and intensely tectonic zones—and offers detailed exploration insights for each category.Each classification exhibits distinct geological and tectonic characteristics that influence heat source mechanisms and resource distribution.Furthermore,this paper documents significant advances in EGS construction,particularly in the Gonghe Basin on the northeastern margin of the Qianghai-Xizang Plateau and the Matouying uplift in the North China Basin,where successful reservoir stimulation,microseismic monitoring,and experimental power generation have been achieved.Despite these developments,challenges persist,including technical adaptability under complex geological conditions and the economic viability of large-scale HDR development.This paper suggests that future initiatives should emphasize resource exploration,technological research,and policy support to foster sustainable HDR resource development in China,thereby contributing to the global energy transition and environmental sustainability.
文摘This paper presents a new power generation structure that can provide DC energy for passive UHF RFID with high sensitivity and high efficiency. The structure is designed with 0.18μm standard CMOS technology, including two charge pumps,a current reference, and a group of bias circuits. Low-voltage performance is improved thanks to the bias structure,which eliminates the threshold voltage drop and body-effect of conventional circuits. A 350mV minimum input level is required to generate a 1.5V power supply for a 100k~ load with power conversion efficiency （PCE） of 22%. PCE up to 29.8% is achieved with a 60kΩ load. Simulation results show that the new circuit is superior to conventional charge pumps.
基金supported by the National Natural Science Foundation of China(No.21878176)National Key Research and Development Program of China(No.2018YFA0902200)financially supported by the Imperial College President’s PhD Scholarship Scheme。
文摘Lignocellulosic biomass has attracted great interest in recent years for energy production due to its renewability and carbon-neutral nature.There are various ways to convert lignocellulose to gaseous,liquid and solid fuels via thermochemical,chemical or biological approaches.Typical biomass derived fuels include syngas,bio-gas,bio-oil,bioethanol and biochar,all of which could be used as fuels for furnace,engine,turbine or fuel cells.Direct biomass fuel cells mediated by various electron carriers provide a new direction of lignocellulose conversion.Various metal and non-metal based carriers have been screened for mediating the electron transfer from biomass to oxygen thus generating electricity.The power density of direct biomass fuel cells can be over 100 mW cm^(-2),which shows promise for practical applications.Lignocellulose and its isolated components,primarily cellulose and lignin,have also been paid considerable attention as sustainable carbonaceous materials for preparation of electrodes for supercapacitors,lithium-ion batteries and lithium-sulfur batteries.In this paper,we have provided a state-of-the-art review on the research progress of lignocellulosic biomass as feedstock and materials for power generation and energy storage focusing on the chemistry aspects of the processes.It was recommended that process integration should be performed to reduce the cost for thermochemical and biological conversion of lignocellulose to biofuels,while efforts should be made to increase efficiency and improve the properties for biomass fuelled fuel cells and biomass derived electrodes for energy storage.
基金National Natural Science Foundation of China （10972236） The Scientific and Technical Innovation for Postgraduates of Air Force Engineering University （DX2010102）
文摘This paper presents a preliminary experimental investigation on magnetohydrodynamic （MHD） power generation using seeded supersonic argon flow as working fluid. Helium and argon are used as driver and driven gas respectively in a shock tunnel. Equilibrium contact surface operating mode is used to obtain high temperature gas, and the conductivity is obtained by adding seed K2CO3 powder into the driven section. Under the conditions of nozzle inlet total pressure being 0.32 MPa, total temperature 6 504 K, magnetic field density about 0.5 T and nozzle outlet velocity 1 959 m/s, induction voltage and short-circuit current of the segmentation MHD power generation channel are measured, and the experimental results agree with theoretical calculations; the average conductivity is about 20 S/m calculated from characteristics of voltage and current. When load factor is 0.5, the maximum power density of the MHD power generation channel reaches 4.797 1 MW/m3, and the maximum enthalpy extraction rate is 0.34%. Finally, the principle and method of indirect testing for gas state parameters are derived and analyzed.
