This paper uses a Computer Simulation Technology microwave studio to simulate the performance of a new highdirectivity anisotropic magnetic metamaterial antenna loaded with a frequency-selective surface. Frequency-sel...This paper uses a Computer Simulation Technology microwave studio to simulate the performance of a new highdirectivity anisotropic magnetic metamaterial antenna loaded with a frequency-selective surface. Frequency-selective surface with cross-dipole element has a great effect on the directivity, radiation pattern, and gain of such an antenna. The experimental results show that frequency-selective surface （FSS） significantly improve the radiation performance of anisotropic magnetic metamaterial antenna. For example, as a single anisotropic magnetic metamaterial antenna, half power beam width is 4 degrees in the H planes, and the gain of this antenna is 19.5dBi at 10CHz, achieving a 2.1 degree increment in half power beam width, and a 7.3 dB gain increment by loading with the FSS reflector. The simulating results are consistent with our experimental results.展开更多
Double-screen frequency-selective surfaces （FSSs） can bring about a better flattened effect and a rapidly declining edge. They are therefore an effective means to achieve outer-zone stealth of the radar cabin to det...Double-screen frequency-selective surfaces （FSSs） can bring about a better flattened effect and a rapidly declining edge. They are therefore an effective means to achieve outer-zone stealth of the radar cabin to detect radar waves. In this article, a double-screen wide-bandpass FSS structure is designed and the transmission characteristics of the units under alignment and non-alignment are simulated by means of the spectral domain approach. Meanwhile, the experimental parts fabricated by vacuum evaporation and lithography are tested in a microwave chamber. Tile results show that the aligned unit structure has good incident angle stability and can achieve high transmittance when the bandwidth is 3.3 GHz, and the transmission loss is less than -1 dB. When the units have a non-aligned structure, the bandwidth decreases and transmission loss increases with increasing incident angle.展开更多
An experimental double-layer active frequency-selective surface（AFSS） for stealth radome is proposed. The AFSS is a planar structure which is composed of a fixed frequency-selective surface（FSS）, a PIN diodes arra...An experimental double-layer active frequency-selective surface（AFSS） for stealth radome is proposed. The AFSS is a planar structure which is composed of a fixed frequency-selective surface（FSS）, a PIN diodes array, and a DC bias network. The AFSS elements incorporating switchable PIN diodes are discussed. By means of controlling the DC bias network, it is possible to switch the frequency response for reflecting and transmitting. Measured and simulated data validate that when the incidence angle varies from 0°to 30° the AFSS produces more than-11.5 dB isolation across6–18 GHz when forward biased. The insertion loss（IL） is less than 0.5 dB across 10–11 GHz when reverse biased.展开更多
A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect...A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect the two separate parts of the interdigital capacitor is explored to achieve parallel resonance.The equivalent circuit model(ECM)and electric field distributions are introduced to explain frequency performance of FSS.The whole structure has only one layer and possesses a low profile(a thickness of 0.0015λ,where λ represents the resonant wavelength in free space)as well as a small size(0.03λ×0.03λ).This FSS performs as a spatial bandpass filter which exhibits a great angular stability with incident angles ranging from 0° to 80° for both transverse electric(TE)and transverse magnetic(TM)polarizations.As an example,a prototype of one proposed FSS is fabricated and tested.The measured results show a good angular stability.展开更多
A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband a...A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband and exhibits more stable frequency responses and lower insertion loss under wide-angle oblique incidence compared with the typical three-layer metal-dielectric structure.According to the simulation results,the proposed FSS can achieve a passband range of 1.7-2.7 GHz with an insertion loss of less than 0.5 d B and a relative bandwidth of 44.1%,and it can preserve stable transmission characteristics with the incident angle ranging from 0°to 45°.展开更多
An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to wi...An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to widen the wave absorbing bandwidth.Three pieces of magnetic substrates are prepared.According to the complex permittivity and permeability,the reflectivity of the corresponding absorber is calculated by the finite difference time-domain（FDTD） method,and the bandwidth of the reflectivity below 10 dB is optimized by genetic algorithm.The calculated results indicate that the wave absorbing performance is significantly improved by increasing the complex permeability of the substrate;the reflectivity bandwidth below 10 dB of the single layer FSS absorber can reach 3.6-18 GHz with a thickness of 5 mm,which is wider than that with a dielectric substrate.The density of the FSS absorber is only 0.92 g/cm 3.Additionally,the absorption band can be further widened by inserting a second lossy FSS.Finally,a double layer lossy FSS absorber with a magnetic substrate is fabricated based on the design result.The experimental result is consistent with the design one.展开更多
This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element i...This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element is designed by loading the rectangular microstrip element with L-shaped conducting patch at its two ends. Based on the spectral-domain method, the frequency response including angle effect and polarization effect of the frequency selective surface （FSS） structure are analysed and the plots of the frequency versus transmission coefficient are obtained. As a result of the numerical analysis, it is shown that if the source polarization is changed, polarization-independence of previous FSS design can be achieved only for normal incidence, which limits most FSS applications. But in our proposed structure, the better polarization-independency for arbitrary incident angle can be achieved. It is observed that the simulated result comes very close to the experimental result.展开更多
An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loa...An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loaded receiving antenna array. The existing absorber is effectively simplified by withdrawing half of the loaded resistors; a more compact one is obtained when lumped capacitors are introduced. Building on this, a varactor-tunable absorber with a proper bias network is proposed. Numerical simulations of one tunable absorber with 1.6 mm in thickness show that a wide tuning range from 3.05 GHz to 1.96 GHz is achieved by changing the capacitance of the loaded varactor from 0.5 pF to 5.0 pF. An experiment is carried out using a rectangular waveguide measurement setup and excellent agreement between the simulated and measured results is demonstrated.展开更多
Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the d...Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm （GA） when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.展开更多
A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimension...A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimensional periodic array of substrate integrated waveguide cavities, realizing the polarization rotation by coupling the input signal to the output wave through three metallic slots. Two layers of frequency selective surfaces are cascaded by substrate and form the polarization rotator. A vertical slot on the top layer is used to select the horizontal polarization from the incident wave, the vertical and the horizontal slots on the bottom layer are, respectively, used to obtain horizontally and vertically polarized outgoing waves. The two orthogonal outgoing waves are combined to result in the 45~ polarized wave. Both full wave simulation and experimental measurement are carried out, together validating the proposed method.展开更多
Based on previous work, a novel Frequency Selective Surface (FSS) consisting of two metallic layers is proposed. The first layer is inductive-designed to generate the band-pass performance, while the second layer is c...Based on previous work, a novel Frequency Selective Surface (FSS) consisting of two metallic layers is proposed. The first layer is inductive-designed to generate the band-pass performance, while the second layer is capacitive-designed so that the miniaturization characteristic can be further improved. As a result, compared with the traditional single-layer structure, the profile of the FSS proposed is relatively small with the cell’s dimension only 0.0814λ × 0.0814λ. Moreover, the structure’s stability corresponding to waves of different polarizations and incident angles are also testified, which ensures the practicability of the proposed structure.展开更多
In this work,we propose an all-dielectric frequency selective surface（FSS） composed of periodically placed highpermittivity dielectric resonators and a three-dimensional（3D） printed supporter.Mie resonances in the...In this work,we propose an all-dielectric frequency selective surface（FSS） composed of periodically placed highpermittivity dielectric resonators and a three-dimensional（3D） printed supporter.Mie resonances in the dielectric resonators offer strong electric and magnetic dipoles,quadrupoles,and higher order terms.The re-radiated electric and magnetic fields by these multipoles interact with the incident fields,which leads to total reflection or total transmission in some special frequency bands.The measured results of the fabricated FSS demonstrate a stopband fractional bandwidth（FBW）of 22.2%,which is consistent with the simulated result.展开更多
A thick-screen frequency selective surface （FSS） has not only a broad bandwidth but also the advantages of overcoming the multilayer FSS shortcoming of complex structure and low transmittance of centre frequency due...A thick-screen frequency selective surface （FSS） has not only a broad bandwidth but also the advantages of overcoming the multilayer FSS shortcoming of complex structure and low transmittance of centre frequency due to the cascade of FSSs, and this means it could potentially be applied in a stealth curved streamlined radome. However, there is an unsteadiness of centre frequency in a wide range of incident angles and another unsteadiness of polarization in a big incident angle. In order to solve these problems, in this paper we provide a novel four-legged loaded element thick-screen FSS. The structure is analysed and simulated using the mode matching method and moment method. The centre frequency, the transmittance of centre frequency, and bandwidth of the structure are investigated when some parameters including the polarization at a big incident angle and the incident angles of TE ＆： TM waves are changed. The novel four-legged loaded element thick-screen FSS has better transmission properties with a better steadiness of polarization and incident angle independence. The novel structure of the four-legged loaded element thick-screen FSS provides a valuable reference for their application in a stealth curved streamlined radome.展开更多
A band-pass frequency selective surface(FSS) with polarization rotation property is proposed. The proposed polarization rotating FSS(PR-FSS) is a two-dimensional periodic structure, its unit cell is an antenna-filter-...A band-pass frequency selective surface(FSS) with polarization rotation property is proposed. The proposed polarization rotating FSS(PR-FSS) is a two-dimensional periodic structure, its unit cell is an antenna-filter-antenna(AFA) module,and the polarization directions of the upper and lower antennas in each AFA module are orthogonal to each other, so the PR-FSS can achieve frequency selection and 90 degrees polarization rotation at the same time. The numerical simulation demonstrate that the anticipated frequency selection and polarization rotation are realized by the PR-FSS in the frequency band from 8.84 GHz to 10.30 GHz with a relative bandwidth of 15.26%, and the maximum insertion loss in the pass band is only 0.17 d B. Finally, one effective experiment validation is carried out, a reasonable agreement is observed between the experimental and simulated results except for a slight deviation caused by fabrication error and measurement tolerance.展开更多
Today's antennas have to operate in multiple resonant frequencies to satisfy the need of recent advances in communication technologies.This paper presents split ring resonator based triangular multiband antenna wh...Today's antennas have to operate in multiple resonant frequencies to satisfy the need of recent advances in communication technologies.This paper presents split ring resonator based triangular multiband antenna whose antenna performance is enhanced with the help of frequency selective surfaces(FSSs).The antenna has multiple resonances at S,C,and X bands.An array of 4×3 crisscross-shaped unit cells are arranged to form the FSS layer.The antenna is fed with a microstrip line feeding technique.The proposed antenna operates at 3.5 GHz,4.1 GHz,5.5GHz,9.4GHz,and 9.8 GHz with a better return loss and gain.Simulated and measured results yield a good match.展开更多
That whether unidirectional tension changes the influence of incident angle on FSS's(frequency selective surface) electromagnetic(EM) property and whether incident angle changes the effect of unidirectional intens...That whether unidirectional tension changes the influence of incident angle on FSS's(frequency selective surface) electromagnetic(EM) property and whether incident angle changes the effect of unidirectional intension on FSS's EM property is researched.The pattern and magnitude of these changes are revealed.Firstly,the analyses for the mechanism of unidirectional tension's influence and the mechanism of the coupling between the influences of unidirectional tension and incident angle are conducted.Then,according to the mechanism of these influences,Mechanics-Electromagnetics co-analysis is conducted based on mechanics finite element method and electromagnetics finite element method.The frequency responses of the FSS which is under different unidirectional tensions and illuminated by EM wave incident at different angles are gained.The concept"unidirectional tensile sensitivity of FSS"is put forward along with two unidirectional tensile sensitivity factors.By using angular sensitivity-factor and unidirectional tensile sensitivity-factor,the influences of unidirectional tension and incident angle,which are coupled with each other,are expatiated respectively.Research results show that these influences have two sides.Meanwhile,basing on Mode Matching Method and according to the results of numerical investigation,one principle for the layout of FSS with apertures is gained.Several suggestions for further research are given.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No 60371010)
文摘This paper uses a Computer Simulation Technology microwave studio to simulate the performance of a new highdirectivity anisotropic magnetic metamaterial antenna loaded with a frequency-selective surface. Frequency-selective surface with cross-dipole element has a great effect on the directivity, radiation pattern, and gain of such an antenna. The experimental results show that frequency-selective surface （FSS） significantly improve the radiation performance of anisotropic magnetic metamaterial antenna. For example, as a single anisotropic magnetic metamaterial antenna, half power beam width is 4 degrees in the H planes, and the gain of this antenna is 19.5dBi at 10CHz, achieving a 2.1 degree increment in half power beam width, and a 7.3 dB gain increment by loading with the FSS reflector. The simulating results are consistent with our experimental results.
基金supported by the Doctoral Fund of the Ministry of Education of China (Grant No. 20092216120005)the National Natural Science Foundation of China (Grant No. 41004042)
文摘Double-screen frequency-selective surfaces （FSSs） can bring about a better flattened effect and a rapidly declining edge. They are therefore an effective means to achieve outer-zone stealth of the radar cabin to detect radar waves. In this article, a double-screen wide-bandpass FSS structure is designed and the transmission characteristics of the units under alignment and non-alignment are simulated by means of the spectral domain approach. Meanwhile, the experimental parts fabricated by vacuum evaporation and lithography are tested in a microwave chamber. Tile results show that the aligned unit structure has good incident angle stability and can achieve high transmittance when the bandwidth is 3.3 GHz, and the transmission loss is less than -1 dB. When the units have a non-aligned structure, the bandwidth decreases and transmission loss increases with increasing incident angle.
基金Project supported by the National Basic Resarch Program of China(Grant No.2014CB339800)the National Natural Science Foundation of China(Grant No.11173015)
文摘An experimental double-layer active frequency-selective surface（AFSS） for stealth radome is proposed. The AFSS is a planar structure which is composed of a fixed frequency-selective surface（FSS）, a PIN diodes array, and a DC bias network. The AFSS elements incorporating switchable PIN diodes are discussed. By means of controlling the DC bias network, it is possible to switch the frequency response for reflecting and transmitting. Measured and simulated data validate that when the incidence angle varies from 0°to 30° the AFSS produces more than-11.5 dB isolation across6–18 GHz when forward biased. The insertion loss（IL） is less than 0.5 dB across 10–11 GHz when reverse biased.
基金supported by the Aeronautical Science Foundation of China(2017ZF37005)the National Natural Science Foundation of China(62001389).
文摘A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect the two separate parts of the interdigital capacitor is explored to achieve parallel resonance.The equivalent circuit model(ECM)and electric field distributions are introduced to explain frequency performance of FSS.The whole structure has only one layer and possesses a low profile(a thickness of 0.0015λ,where λ represents the resonant wavelength in free space)as well as a small size(0.03λ×0.03λ).This FSS performs as a spatial bandpass filter which exhibits a great angular stability with incident angles ranging from 0° to 80° for both transverse electric(TE)and transverse magnetic(TM)polarizations.As an example,a prototype of one proposed FSS is fabricated and tested.The measured results show a good angular stability.
基金supported by ZTE Industry-University-Institute Cooperation Funds under Grant No.IA20220800001。
文摘A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband and exhibits more stable frequency responses and lower insertion loss under wide-angle oblique incidence compared with the typical three-layer metal-dielectric structure.According to the simulation results,the proposed FSS can achieve a passband range of 1.7-2.7 GHz with an insertion loss of less than 0.5 d B and a relative bandwidth of 44.1%,and it can preserve stable transmission characteristics with the incident angle ranging from 0°to 45°.
文摘An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to widen the wave absorbing bandwidth.Three pieces of magnetic substrates are prepared.According to the complex permittivity and permeability,the reflectivity of the corresponding absorber is calculated by the finite difference time-domain（FDTD） method,and the bandwidth of the reflectivity below 10 dB is optimized by genetic algorithm.The calculated results indicate that the wave absorbing performance is significantly improved by increasing the complex permeability of the substrate;the reflectivity bandwidth below 10 dB of the single layer FSS absorber can reach 3.6-18 GHz with a thickness of 5 mm,which is wider than that with a dielectric substrate.The density of the FSS absorber is only 0.92 g/cm 3.Additionally,the absorption band can be further widened by inserting a second lossy FSS.Finally,a double layer lossy FSS absorber with a magnetic substrate is fabricated based on the design result.The experimental result is consistent with the design one.
基金supported by the National Defense Innovation Foundation of Chinese Academy of Sciences (Grant No CXJJ-149)
文摘This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element is designed by loading the rectangular microstrip element with L-shaped conducting patch at its two ends. Based on the spectral-domain method, the frequency response including angle effect and polarization effect of the frequency selective surface （FSS） structure are analysed and the plots of the frequency versus transmission coefficient are obtained. As a result of the numerical analysis, it is shown that if the source polarization is changed, polarization-independence of previous FSS design can be achieved only for normal incidence, which limits most FSS applications. But in our proposed structure, the better polarization-independency for arbitrary incident angle can be achieved. It is observed that the simulated result comes very close to the experimental result.
基金Project supported by the National Natural Science Foundations of China (Grant Nos.61271250 and 61202490)
文摘An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loaded receiving antenna array. The existing absorber is effectively simplified by withdrawing half of the loaded resistors; a more compact one is obtained when lumped capacitors are introduced. Building on this, a varactor-tunable absorber with a proper bias network is proposed. Numerical simulations of one tunable absorber with 1.6 mm in thickness show that a wide tuning range from 3.05 GHz to 1.96 GHz is achieved by changing the capacitance of the loaded varactor from 0.5 pF to 5.0 pF. An experiment is carried out using a rectangular waveguide measurement setup and excellent agreement between the simulated and measured results is demonstrated.
基金Project supported by the National Natural Science Foundation of China (Grant No 10647105)
文摘Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm （GA） when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.60990322,60990320,60801001,and 61101011)the Key Grant Project of Ministry of Education of China(Grant No.313029)+1 种基金the Ph.D.Program Foundation of Ministry of Education of China(Grant Nos.20100091110036 and 20120091110032)the Jiangsu Key Laboratory of Advanced Techniques for Manipulating Electromagnetic Waves,China
文摘A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimensional periodic array of substrate integrated waveguide cavities, realizing the polarization rotation by coupling the input signal to the output wave through three metallic slots. Two layers of frequency selective surfaces are cascaded by substrate and form the polarization rotator. A vertical slot on the top layer is used to select the horizontal polarization from the incident wave, the vertical and the horizontal slots on the bottom layer are, respectively, used to obtain horizontally and vertically polarized outgoing waves. The two orthogonal outgoing waves are combined to result in the 45~ polarized wave. Both full wave simulation and experimental measurement are carried out, together validating the proposed method.
文摘Based on previous work, a novel Frequency Selective Surface (FSS) consisting of two metallic layers is proposed. The first layer is inductive-designed to generate the band-pass performance, while the second layer is capacitive-designed so that the miniaturization characteristic can be further improved. As a result, compared with the traditional single-layer structure, the profile of the FSS proposed is relatively small with the cell’s dimension only 0.0814λ × 0.0814λ. Moreover, the structure’s stability corresponding to waves of different polarizations and incident angles are also testified, which ensures the practicability of the proposed structure.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61201030,61372045,61472045,and 61401229)the Science and Technology Project of Jiangsu Province,China(Grant No.BE2015002)+1 种基金the Open Research Program of the State Key Laboratory of Millimeter Waves,China(Grant Nos.K201616 and K201622)the Nanjing University of Posts and Telecommunications Scientific Foundation,China(Grant No.NY214148)
文摘In this work,we propose an all-dielectric frequency selective surface（FSS） composed of periodically placed highpermittivity dielectric resonators and a three-dimensional（3D） printed supporter.Mie resonances in the dielectric resonators offer strong electric and magnetic dipoles,quadrupoles,and higher order terms.The re-radiated electric and magnetic fields by these multipoles interact with the incident fields,which leads to total reflection or total transmission in some special frequency bands.The measured results of the fabricated FSS demonstrate a stopband fractional bandwidth（FBW）of 22.2%,which is consistent with the simulated result.
文摘A thick-screen frequency selective surface （FSS） has not only a broad bandwidth but also the advantages of overcoming the multilayer FSS shortcoming of complex structure and low transmittance of centre frequency due to the cascade of FSSs, and this means it could potentially be applied in a stealth curved streamlined radome. However, there is an unsteadiness of centre frequency in a wide range of incident angles and another unsteadiness of polarization in a big incident angle. In order to solve these problems, in this paper we provide a novel four-legged loaded element thick-screen FSS. The structure is analysed and simulated using the mode matching method and moment method. The centre frequency, the transmittance of centre frequency, and bandwidth of the structure are investigated when some parameters including the polarization at a big incident angle and the incident angles of TE ＆： TM waves are changed. The novel four-legged loaded element thick-screen FSS has better transmission properties with a better steadiness of polarization and incident angle independence. The novel structure of the four-legged loaded element thick-screen FSS provides a valuable reference for their application in a stealth curved streamlined radome.
基金supported by the National Natural Science Foundation of China (Grant No. 62072378)Xi’an Science and Technology Plan Project, China (Grant No. GXYD20.4)。
文摘A band-pass frequency selective surface(FSS) with polarization rotation property is proposed. The proposed polarization rotating FSS(PR-FSS) is a two-dimensional periodic structure, its unit cell is an antenna-filter-antenna(AFA) module,and the polarization directions of the upper and lower antennas in each AFA module are orthogonal to each other, so the PR-FSS can achieve frequency selection and 90 degrees polarization rotation at the same time. The numerical simulation demonstrate that the anticipated frequency selection and polarization rotation are realized by the PR-FSS in the frequency band from 8.84 GHz to 10.30 GHz with a relative bandwidth of 15.26%, and the maximum insertion loss in the pass band is only 0.17 d B. Finally, one effective experiment validation is carried out, a reasonable agreement is observed between the experimental and simulated results except for a slight deviation caused by fabrication error and measurement tolerance.
文摘Today's antennas have to operate in multiple resonant frequencies to satisfy the need of recent advances in communication technologies.This paper presents split ring resonator based triangular multiband antenna whose antenna performance is enhanced with the help of frequency selective surfaces(FSSs).The antenna has multiple resonances at S,C,and X bands.An array of 4×3 crisscross-shaped unit cells are arranged to form the FSS layer.The antenna is fed with a microstrip line feeding technique.The proposed antenna operates at 3.5 GHz,4.1 GHz,5.5GHz,9.4GHz,and 9.8 GHz with a better return loss and gain.Simulated and measured results yield a good match.
基金the Defense Science and Technology Advance-research for Ship Industry
文摘That whether unidirectional tension changes the influence of incident angle on FSS's(frequency selective surface) electromagnetic(EM) property and whether incident angle changes the effect of unidirectional intension on FSS's EM property is researched.The pattern and magnitude of these changes are revealed.Firstly,the analyses for the mechanism of unidirectional tension's influence and the mechanism of the coupling between the influences of unidirectional tension and incident angle are conducted.Then,according to the mechanism of these influences,Mechanics-Electromagnetics co-analysis is conducted based on mechanics finite element method and electromagnetics finite element method.The frequency responses of the FSS which is under different unidirectional tensions and illuminated by EM wave incident at different angles are gained.The concept"unidirectional tensile sensitivity of FSS"is put forward along with two unidirectional tensile sensitivity factors.By using angular sensitivity-factor and unidirectional tensile sensitivity-factor,the influences of unidirectional tension and incident angle,which are coupled with each other,are expatiated respectively.Research results show that these influences have two sides.Meanwhile,basing on Mode Matching Method and according to the results of numerical investigation,one principle for the layout of FSS with apertures is gained.Several suggestions for further research are given.
