The high-frequency(HF) communication is one of essential communication methods for military and emergency application. However, the selection of communication frequency channel is always a difficult problem as the cro...The high-frequency(HF) communication is one of essential communication methods for military and emergency application. However, the selection of communication frequency channel is always a difficult problem as the crowded spectrum, the time-varying channels, and the malicious intelligent jamming. The existing frequency hopping, automatic link establishment and some new anti-jamming technologies can not completely solve the above problems. In this article, we adopt deep reinforcement learning to solve this intractable challenge. First, the combination of the spectrum state and the channel gain state is defined as the complex environmental state, and the Markov characteristic of defined state is analyzed and proved. Then, considering that the spectrum state and channel gain state are heterogeneous information, a new deep Q network(DQN) framework is designed, which contains multiple sub-networks to process different kinds of information. Finally, aiming to improve the learning speed and efficiency, the optimization targets of corresponding sub-networks are reasonably designed, and a heterogeneous information fusion deep reinforcement learning(HIF-DRL) algorithm is designed for the specific frequency selection. Simulation results show that the proposed algorithm performs well in channel prediction, jamming avoidance and frequency channel selection.展开更多
In fifth-generation wireless communication system(5G),more connections are built between metaheuristics and electromagnetic equipment design.In this paper,we propose a self-adaptive grey wolf optimizer(SAGWO)combined ...In fifth-generation wireless communication system(5G),more connections are built between metaheuristics and electromagnetic equipment design.In this paper,we propose a self-adaptive grey wolf optimizer(SAGWO)combined with a novel optimization model of a 5G frequency selection surface(FSS)based on FSS unit nodes.SAGWO includes three improvement strategies,improving the initial distribution,increasing the randomness,and enhancing the local search,to accelerate the convergence and effectively avoid local optima.In benchmark tests,the proposed optimizer performs better than the five other optimization algorithms:original grey wolf optimizer(GWO),genetic algorithm(GA),particle swarm optimizer(PSO),improved grey wolf optimizer(IGWO),and selective opposition based grey wolf optimization(SOGWO).Due to its global searchability,SAGWO is suitable for solving the optimization problem of a 5G FSS that has a large design space.The combination of SAGWO and the new FSS optimization model can automatically obtain the shape of the FSS unit with electromagnetic interference shielding capability at the center operating frequency.To verify the performance of the proposed method,a double-layer ring FSS is designed with the purpose of providing electromagnetic interference shielding features at28 GHz.The results show that the optimized FSS has better electromagnetic interference shielding at the center frequency and has higher angular stability.Finally,a sample of the optimized FSS is fabricated and tested.展开更多
The underlying study investigates single valued neutrosophic entropy based adaptive sensitive frequency band selection for variational mode decomposition(VMD)for the purpose of identifying defective components in an a...The underlying study investigates single valued neutrosophic entropy based adaptive sensitive frequency band selection for variational mode decomposition(VMD)for the purpose of identifying defective components in an axial pump.The proposed methodology is applied in the following steps.First,VMD is applied for decomposing vibration signals into various frequency bands,called as modes.After computing energy of each VMD,the lower(minimum)and upper(maximum)bounds from these energy readings are extracted for defect conditions,such as outer race,inner race,worn piston,faulty cylinder and valve plate,and blocked hole of the piston.Thereafter,energy interval ranges are obtained and further converted into the form of single valued neutrosophic sets(SVNSs).Then,the proposed neutrosophic entropy measure is deployed for quantifying the non-linear connection between each bearing defect conditions and various frequency bands.The mode having maximum neutrosophic entropy value is designated to the“most sensitive”frequency band.Thereafter,envelope demodulation is applied to the most sensitive selected frequency band for finding defective components.The proposed neutrosophic entropy and VMD based methodology is effective in providing a better insight for selecting suitable frequency band for carrying out envelope demodulation in comparison to existing methods.展开更多
A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband a...A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband and exhibits more stable frequency responses and lower insertion loss under wide-angle oblique incidence compared with the typical three-layer metal-dielectric structure.According to the simulation results,the proposed FSS can achieve a passband range of 1.7-2.7 GHz with an insertion loss of less than 0.5 d B and a relative bandwidth of 44.1%,and it can preserve stable transmission characteristics with the incident angle ranging from 0°to 45°.展开更多
Based on the frequency domain training sequences, the polynomial-based carrier frequency offset （CFO） estimation in multiple-input multiple-output （ MIMO ） orthogonal frequency division multiplexing （ OFDM ） sys...Based on the frequency domain training sequences, the polynomial-based carrier frequency offset （CFO） estimation in multiple-input multiple-output （ MIMO ） orthogonal frequency division multiplexing （ OFDM ） systems is extensively investigated. By designing the training sequences to meet certain conditions and exploiting the Hermitian and real symmetric properties of the corresponding matrices, it is found that the roots of the polynomials corresponding to the cost functions are pairwise and that both meger CFO and fractional CFO can be estimated by the direct polynomial rooting approach. By analyzing the polynomials corresponding to the cost functions and their derivatives, it is shown that they have a common polynomial factor and the former can be expressed in a quadratic form of the common polynomial factor. Analytical results further reveal that the derivative polynomial rooting approach is equivalent to the direct one in estimation at the same signal-to-noise ratio（SNR） value and that the latter is superior to the former in complexity. Simulation results agree well with analytical results.展开更多
Combining suitable microstructure and dielectric-magnetic synergy effect is conducive to achieve lightweight,broadband,and high-efficiency microwave absorbing materials within low filler loading.Herein,porous carbon p...Combining suitable microstructure and dielectric-magnetic synergy effect is conducive to achieve lightweight,broadband,and high-efficiency microwave absorbing materials within low filler loading.Herein,porous carbon polyhedrons coupled with bimetallic CoNi alloys were synthesized by using metalorganic frameworks(MOFs)as a template and subsequent pyrolysis treatment.Electromagnetic analysis indicated that the existence of metal Ni element could influence the wave attenuation capacity effectively,resulting in frequency selective wave absorption performance.Additionally,the pyrolysis temperature was also closely related to wave absorption intensity.The Co_(2)Ni_(1)/C/PVDF composites calcined at 800℃ possessed outstanding wave absorption performance at an ultra-low filler loading of 5 wt%.The minimum reflection loss value achieved-52 dB(10.8 GHz)under the matched thickness of 3 mm.Moreover,the broadest effective absorption bandwidth(RL<-10 dB)reached 6.2 dB(11.8-18 GHz)for Co/C-800/PVDF composites when the thickness turned into 2 mm.The remarkable wave attenuation ability was mainly ascribed to magnetic and dielectric loss,impedance matching as well as porous structure effect.展开更多
Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing perform...Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.展开更多
An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to wi...An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to widen the wave absorbing bandwidth.Three pieces of magnetic substrates are prepared.According to the complex permittivity and permeability,the reflectivity of the corresponding absorber is calculated by the finite difference time-domain（FDTD） method,and the bandwidth of the reflectivity below 10 dB is optimized by genetic algorithm.The calculated results indicate that the wave absorbing performance is significantly improved by increasing the complex permeability of the substrate;the reflectivity bandwidth below 10 dB of the single layer FSS absorber can reach 3.6-18 GHz with a thickness of 5 mm,which is wider than that with a dielectric substrate.The density of the FSS absorber is only 0.92 g/cm 3.Additionally,the absorption band can be further widened by inserting a second lossy FSS.Finally,a double layer lossy FSS absorber with a magnetic substrate is fabricated based on the design result.The experimental result is consistent with the design one.展开更多
We propose an ultrathin wide-band metamaterial absorber （MA） based on a Minkowski （MIK） fractal frequency selective surface and resistive film. This absorber consists of a periodic arrangement of dielectric substr...We propose an ultrathin wide-band metamaterial absorber （MA） based on a Minkowski （MIK） fractal frequency selective surface and resistive film. This absorber consists of a periodic arrangement of dielectric substrates sandwiched with an MIK fractal loop structure electric resonator and a resistive film. The finite element method is used to simulate and analyze the absorption of the MA. Compared with the MA-backed copper film, the designed MA-backed resistive film exhibits an absorption of 90% at a frequency region of 2 GHz-20 GHz. The power loss density distribution of the MA is further illustrated to explain the mechanism of the proposed MA. Simulated absorptions at different incidence cases indicate that this absorber is polarization-insensitive and wide-angled. Finally, further simulated results indicate that the surface resistance of the resistive film and the dielectric constant of the substrate can affect the absorbing property of the MA. This absorber may be used in many military fields.展开更多
In this paper, we present an infrared transparent frequency selective surface（ITFSS） based on iterative metallic meshes, which possesses the properties of high transmittance in infrared band and band-pass effect in ...In this paper, we present an infrared transparent frequency selective surface（ITFSS） based on iterative metallic meshes, which possesses the properties of high transmittance in infrared band and band-pass effect in millimeter wave band. Cross-slot units are designed on the iterative metallic meshes, which is composed of two same square metallic meshes with a misplaced overlap. In the infrared band of 3–5 μm, the ITFSS has an average transmittance of 80% with a Mg F2 substrate. In the millimeter wave band, a transmittance of-0.74 d B at the resonance frequency of 39.4 GHz is obtained. Moreover, theoretical simulations of the ITFSS diffractive characteristics and transmittance response are also investigated in detail. This ITFSS may be an efficient way to achieve the metamaterial millimeter wave/infrared functional film.展开更多
This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element i...This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element is designed by loading the rectangular microstrip element with L-shaped conducting patch at its two ends. Based on the spectral-domain method, the frequency response including angle effect and polarization effect of the frequency selective surface （FSS） structure are analysed and the plots of the frequency versus transmission coefficient are obtained. As a result of the numerical analysis, it is shown that if the source polarization is changed, polarization-independence of previous FSS design can be achieved only for normal incidence, which limits most FSS applications. But in our proposed structure, the better polarization-independency for arbitrary incident angle can be achieved. It is observed that the simulated result comes very close to the experimental result.展开更多
In order to realize the tunable performance of a frequency selective surface （FSS）, a new unit cell is designed in this paper by properly adding two metal shorts to the ring slot. Based on the spectral-domain method...In order to realize the tunable performance of a frequency selective surface （FSS）, a new unit cell is designed in this paper by properly adding two metal shorts to the ring slot. Based on the spectral-domain method, the frequency responses of the FSS structure with two shorts per slot ring are analysed for both the horizontal and the vertical polarizations at the normal incidence. It is demonstrated that the presence of the metal shorts does not affect the resonant frequency of the horizontally polarized wave but doubles the resonant frequency of the vertically polarized wave. Therefore based on the analysis of the novel transmission properties, a new approach to adjusting the resonant frequency by rotating the FSS screen 90° is presented in this paper.展开更多
Inductively coupled channels are based on the electromagnetic induction principle and realize long-distance current signal transmission through seawater.Due to a few difficulties in performing actual experiments,it is...Inductively coupled channels are based on the electromagnetic induction principle and realize long-distance current signal transmission through seawater.Due to a few difficulties in performing actual experiments,it is unclear how the seawater medium affects the frequency selectivity of the current signal.In this paper,a dual dipole model of the inductively coupled seawater transmission channel is established for the traditional short-distance current field transmission mode.The transmission characteristics of electrical signals in seawater are theoretically derived.A platform is used to measure the amplitude-frequency and phase-frequency characteristics of the current signal transmission in seawater with transmission frequencies ranging from 30 kHz to 1 MHz,and transmission distances in the vertical range of 4 m.The COMSOL Multiphysics simulation and practical test analysis are carried out to analyze the frequency selectivity of seawater conductivity.It is proved that the seawater resistance increases as the frequency increases,which is the key problem that affects the current signal.This study provides an important theoretical support and experimental evidence for improving the transmission performance of long-distance underwater current signals.展开更多
Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-j...Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-junction, the electrolyte layer handled at high temperature showed nano-fiber microstructures accompanied with greatly improved salt solubility. Ions with high mobility were confined in the nano-fibrous channels leading to the semiconducting polymer layer,which is favorable for modulating dynamic doping at the semiconducting polymer/electrolyte interface by pulse frequency.Such a device realized synaptic-like frequency selectivity, i.e., depression at low frequency stimulation but potentiation at high-frequency stimulation.展开更多
In this paper, a new observation equation of non-Gaussian frequency selective fading Bell Labs layered space time （BLAST） architecture system is proposed, which is used for frequency selective fading channels and no...In this paper, a new observation equation of non-Gaussian frequency selective fading Bell Labs layered space time （BLAST） architecture system is proposed, which is used for frequency selective fading channels and non-Gaussian noise in an application environment of BLAST system. With othogonal matrix triangularization （QR decomposition） of the channel matrix, the static observation equation of frequency selective fading BLAST system is transformed into a dynamic state space model, and then the particle filter is used for space-time layered detection. Making the full use of the finite alphabet of the digital modulation communication signal, the optimal proposal distribution can be chosen to produce particle and update the weight. Incorporated with current method of reducing error propagation, a new space-time layered detection algorithm is proposed. Simulation result shows the validity of the proposed algorithm.展开更多
Traditional multi-band frequency selective surface （FSS） approaches are hard to achieve a perfect resonance response in a wide band due to the limit of the onset grating lobe frequency determined by the array. To so...Traditional multi-band frequency selective surface （FSS） approaches are hard to achieve a perfect resonance response in a wide band due to the limit of the onset grating lobe frequency determined by the array. To solve this problem, an approach of combining elements in different period to build a hybrid array is presented. The results of series of numerical simulation show that multi-periodicity combined element FSS, which are designed using this approach, usually have much weaker grating lobes than the traditional FSS. Furthermore, their frequency response can be well predicted through the properties of their member element FSS. A prediction method for estimating the degree of expected grating lobe energy loss in designing multi-band FSS using this approach is provided.展开更多
Tunnel seismic detection methods are effective for obtaining the geological structure around the tunnel face,which is critical for safe construction and disaster mitigation in tunnel engineering.However,there is often...Tunnel seismic detection methods are effective for obtaining the geological structure around the tunnel face,which is critical for safe construction and disaster mitigation in tunnel engineering.However,there is often a lack of accuracy in the acquired geological information and physical properties ahead of the tunnel face in the current tunnel seismic detection methods.Thus,we apply a frequency-domain acoustic full-waveform inversion(FWI)method to obtain high-resolution results for the tunnel structure.We discuss the influence of the frequency group selection strategy and the tunnel observation system settings regarding the inversion results and determine the structural imaging and physical property parameter inversion of abnormal geological bodies ahead of the tunnel face.Based on the conventional strategies of frequency-domain acoustic FWI,we propose a frequency group selection strategy that combines a low-frequency selection covering the vertical wavenumber and a high-frequency selection of antialiasing.This strategy can effectively obtain the spatial structure and physical parameters of the geology ahead of the tunnel face and improve the inversion resolution.In addition,by linearly increasing the side length of the tunnel observation system,we share the influence of the length of the two sides of the observation systems of different tunnels on the inversion results.We found out that the inversion results are the best when the side length is approximately five times the width of the tunnel face,and the influence of increasing the side observation length beyond this range on the inversion results can be ignored.Finally,based on this approach,we invert for the complex multi-stratum model,and an accurate structure and physical property parameters of the complex stratum ahead of the tunnel face are obtained,which verifies the feasibility of the proposed method.展开更多
An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loa...An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loaded receiving antenna array. The existing absorber is effectively simplified by withdrawing half of the loaded resistors; a more compact one is obtained when lumped capacitors are introduced. Building on this, a varactor-tunable absorber with a proper bias network is proposed. Numerical simulations of one tunable absorber with 1.6 mm in thickness show that a wide tuning range from 3.05 GHz to 1.96 GHz is achieved by changing the capacitance of the loaded varactor from 0.5 pF to 5.0 pF. An experiment is carried out using a rectangular waveguide measurement setup and excellent agreement between the simulated and measured results is demonstrated.展开更多
Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the d...Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm （GA） when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.展开更多
A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimension...A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimensional periodic array of substrate integrated waveguide cavities, realizing the polarization rotation by coupling the input signal to the output wave through three metallic slots. Two layers of frequency selective surfaces are cascaded by substrate and form the polarization rotator. A vertical slot on the top layer is used to select the horizontal polarization from the incident wave, the vertical and the horizontal slots on the bottom layer are, respectively, used to obtain horizontally and vertically polarized outgoing waves. The two orthogonal outgoing waves are combined to result in the 45~ polarized wave. Both full wave simulation and experimental measurement are carried out, together validating the proposed method.展开更多
基金supported by Guangxi key Laboratory Fund of Embedded Technology and Intelligent System under Grant No. 2018B-1the Natural Science Foundation for Distinguished Young Scholars of Jiangsu Province under Grant No. BK20160034+1 种基金the National Natural Science Foundation of China under Grant No. 61771488, No. 61671473 and No. 61631020in part by the Open Research Foundation of Science and Technology on Communication Networks Laboratory
文摘The high-frequency(HF) communication is one of essential communication methods for military and emergency application. However, the selection of communication frequency channel is always a difficult problem as the crowded spectrum, the time-varying channels, and the malicious intelligent jamming. The existing frequency hopping, automatic link establishment and some new anti-jamming technologies can not completely solve the above problems. In this article, we adopt deep reinforcement learning to solve this intractable challenge. First, the combination of the spectrum state and the channel gain state is defined as the complex environmental state, and the Markov characteristic of defined state is analyzed and proved. Then, considering that the spectrum state and channel gain state are heterogeneous information, a new deep Q network(DQN) framework is designed, which contains multiple sub-networks to process different kinds of information. Finally, aiming to improve the learning speed and efficiency, the optimization targets of corresponding sub-networks are reasonably designed, and a heterogeneous information fusion deep reinforcement learning(HIF-DRL) algorithm is designed for the specific frequency selection. Simulation results show that the proposed algorithm performs well in channel prediction, jamming avoidance and frequency channel selection.
基金Project supported by the Guangdong Basic and Applied Basic Research FoundationChina(No.2019A1515011783)the National Natural Science Foundation of China(No.52075184)。
文摘In fifth-generation wireless communication system(5G),more connections are built between metaheuristics and electromagnetic equipment design.In this paper,we propose a self-adaptive grey wolf optimizer(SAGWO)combined with a novel optimization model of a 5G frequency selection surface(FSS)based on FSS unit nodes.SAGWO includes three improvement strategies,improving the initial distribution,increasing the randomness,and enhancing the local search,to accelerate the convergence and effectively avoid local optima.In benchmark tests,the proposed optimizer performs better than the five other optimization algorithms:original grey wolf optimizer(GWO),genetic algorithm(GA),particle swarm optimizer(PSO),improved grey wolf optimizer(IGWO),and selective opposition based grey wolf optimization(SOGWO).Due to its global searchability,SAGWO is suitable for solving the optimization problem of a 5G FSS that has a large design space.The combination of SAGWO and the new FSS optimization model can automatically obtain the shape of the FSS unit with electromagnetic interference shielding capability at the center operating frequency.To verify the performance of the proposed method,a double-layer ring FSS is designed with the purpose of providing electromagnetic interference shielding features at28 GHz.The results show that the optimized FSS has better electromagnetic interference shielding at the center frequency and has higher angular stability.Finally,a sample of the optimized FSS is fabricated and tested.
基金co-supported by the National Natural Science Foundation of China(Nos.U1909217,U1709208)the Zhejiang Provincial Natural Science Foundation of China(No.LD21E050001)the Zhejiang Special Support Program for High-level Personnel Recruitment of China(No.2018R52034).
文摘The underlying study investigates single valued neutrosophic entropy based adaptive sensitive frequency band selection for variational mode decomposition(VMD)for the purpose of identifying defective components in an axial pump.The proposed methodology is applied in the following steps.First,VMD is applied for decomposing vibration signals into various frequency bands,called as modes.After computing energy of each VMD,the lower(minimum)and upper(maximum)bounds from these energy readings are extracted for defect conditions,such as outer race,inner race,worn piston,faulty cylinder and valve plate,and blocked hole of the piston.Thereafter,energy interval ranges are obtained and further converted into the form of single valued neutrosophic sets(SVNSs).Then,the proposed neutrosophic entropy measure is deployed for quantifying the non-linear connection between each bearing defect conditions and various frequency bands.The mode having maximum neutrosophic entropy value is designated to the“most sensitive”frequency band.Thereafter,envelope demodulation is applied to the most sensitive selected frequency band for finding defective components.The proposed neutrosophic entropy and VMD based methodology is effective in providing a better insight for selecting suitable frequency band for carrying out envelope demodulation in comparison to existing methods.
基金supported by ZTE Industry-University-Institute Cooperation Funds under Grant No.IA20220800001。
文摘A wide passband frequency selective surface(FSS)is proposed using a five-layer stacked structure.The proposed structure applies four layers of dielectric plates and five layers of metal patches to provide a passband and exhibits more stable frequency responses and lower insertion loss under wide-angle oblique incidence compared with the typical three-layer metal-dielectric structure.According to the simulation results,the proposed FSS can achieve a passband range of 1.7-2.7 GHz with an insertion loss of less than 0.5 d B and a relative bandwidth of 44.1%,and it can preserve stable transmission characteristics with the incident angle ranging from 0°to 45°.
基金The National Natural Science Foundation of China(No.60702028)the National High Technology Research and Development Program of China(863Program)(No.2007AA01Z268)
文摘Based on the frequency domain training sequences, the polynomial-based carrier frequency offset （CFO） estimation in multiple-input multiple-output （ MIMO ） orthogonal frequency division multiplexing （ OFDM ） systems is extensively investigated. By designing the training sequences to meet certain conditions and exploiting the Hermitian and real symmetric properties of the corresponding matrices, it is found that the roots of the polynomials corresponding to the cost functions are pairwise and that both meger CFO and fractional CFO can be estimated by the direct polynomial rooting approach. By analyzing the polynomials corresponding to the cost functions and their derivatives, it is shown that they have a common polynomial factor and the former can be expressed in a quadratic form of the common polynomial factor. Analytical results further reveal that the derivative polynomial rooting approach is equivalent to the direct one in estimation at the same signal-to-noise ratio（SNR） value and that the latter is superior to the former in complexity. Simulation results agree well with analytical results.
基金supported by the National Natural Science Foundation of China(No.52073010)Beijing Natural Science Foundation(2214069)。
文摘Combining suitable microstructure and dielectric-magnetic synergy effect is conducive to achieve lightweight,broadband,and high-efficiency microwave absorbing materials within low filler loading.Herein,porous carbon polyhedrons coupled with bimetallic CoNi alloys were synthesized by using metalorganic frameworks(MOFs)as a template and subsequent pyrolysis treatment.Electromagnetic analysis indicated that the existence of metal Ni element could influence the wave attenuation capacity effectively,resulting in frequency selective wave absorption performance.Additionally,the pyrolysis temperature was also closely related to wave absorption intensity.The Co_(2)Ni_(1)/C/PVDF composites calcined at 800℃ possessed outstanding wave absorption performance at an ultra-low filler loading of 5 wt%.The minimum reflection loss value achieved-52 dB(10.8 GHz)under the matched thickness of 3 mm.Moreover,the broadest effective absorption bandwidth(RL<-10 dB)reached 6.2 dB(11.8-18 GHz)for Co/C-800/PVDF composites when the thickness turned into 2 mm.The remarkable wave attenuation ability was mainly ascribed to magnetic and dielectric loss,impedance matching as well as porous structure effect.
基金supported by National Natural Science Foundation of China(No.52103361)Shaanxi University Youth Outstanding Talents Support Plan,Scientific and Technological Plan Project of Xi’an Beilin District(No.GX2143)。
文摘Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.
文摘An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to widen the wave absorbing bandwidth.Three pieces of magnetic substrates are prepared.According to the complex permittivity and permeability,the reflectivity of the corresponding absorber is calculated by the finite difference time-domain（FDTD） method,and the bandwidth of the reflectivity below 10 dB is optimized by genetic algorithm.The calculated results indicate that the wave absorbing performance is significantly improved by increasing the complex permeability of the substrate;the reflectivity bandwidth below 10 dB of the single layer FSS absorber can reach 3.6-18 GHz with a thickness of 5 mm,which is wider than that with a dielectric substrate.The density of the FSS absorber is only 0.92 g/cm 3.Additionally,the absorption band can be further widened by inserting a second lossy FSS.Finally,a double layer lossy FSS absorber with a magnetic substrate is fabricated based on the design result.The experimental result is consistent with the design one.
基金supported by the National Natural Science Foundation of China (Grant No. 51207060)the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20090142110004)
文摘We propose an ultrathin wide-band metamaterial absorber （MA） based on a Minkowski （MIK） fractal frequency selective surface and resistive film. This absorber consists of a periodic arrangement of dielectric substrates sandwiched with an MIK fractal loop structure electric resonator and a resistive film. The finite element method is used to simulate and analyze the absorption of the MA. Compared with the MA-backed copper film, the designed MA-backed resistive film exhibits an absorption of 90% at a frequency region of 2 GHz-20 GHz. The power loss density distribution of the MA is further illustrated to explain the mechanism of the proposed MA. Simulated absorptions at different incidence cases indicate that this absorber is polarization-insensitive and wide-angled. Finally, further simulated results indicate that the surface resistance of the resistive film and the dielectric constant of the substrate can affect the absorbing property of the MA. This absorber may be used in many military fields.
基金supported by the National Natural Science Foundation of China(Grant No.61401424)
文摘In this paper, we present an infrared transparent frequency selective surface（ITFSS） based on iterative metallic meshes, which possesses the properties of high transmittance in infrared band and band-pass effect in millimeter wave band. Cross-slot units are designed on the iterative metallic meshes, which is composed of two same square metallic meshes with a misplaced overlap. In the infrared band of 3–5 μm, the ITFSS has an average transmittance of 80% with a Mg F2 substrate. In the millimeter wave band, a transmittance of-0.74 d B at the resonance frequency of 39.4 GHz is obtained. Moreover, theoretical simulations of the ITFSS diffractive characteristics and transmittance response are also investigated in detail. This ITFSS may be an efficient way to achieve the metamaterial millimeter wave/infrared functional film.
基金supported by the National Defense Innovation Foundation of Chinese Academy of Sciences (Grant No CXJJ-149)
文摘This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element is designed by loading the rectangular microstrip element with L-shaped conducting patch at its two ends. Based on the spectral-domain method, the frequency response including angle effect and polarization effect of the frequency selective surface （FSS） structure are analysed and the plots of the frequency versus transmission coefficient are obtained. As a result of the numerical analysis, it is shown that if the source polarization is changed, polarization-independence of previous FSS design can be achieved only for normal incidence, which limits most FSS applications. But in our proposed structure, the better polarization-independency for arbitrary incident angle can be achieved. It is observed that the simulated result comes very close to the experimental result.
基金Project supported by the National Natural Science Foundation of China (Grant No. 61172012)
文摘In order to realize the tunable performance of a frequency selective surface （FSS）, a new unit cell is designed in this paper by properly adding two metal shorts to the ring slot. Based on the spectral-domain method, the frequency responses of the FSS structure with two shorts per slot ring are analysed for both the horizontal and the vertical polarizations at the normal incidence. It is demonstrated that the presence of the metal shorts does not affect the resonant frequency of the horizontally polarized wave but doubles the resonant frequency of the vertically polarized wave. Therefore based on the analysis of the novel transmission properties, a new approach to adjusting the resonant frequency by rotating the FSS screen 90° is presented in this paper.
文摘Inductively coupled channels are based on the electromagnetic induction principle and realize long-distance current signal transmission through seawater.Due to a few difficulties in performing actual experiments,it is unclear how the seawater medium affects the frequency selectivity of the current signal.In this paper,a dual dipole model of the inductively coupled seawater transmission channel is established for the traditional short-distance current field transmission mode.The transmission characteristics of electrical signals in seawater are theoretically derived.A platform is used to measure the amplitude-frequency and phase-frequency characteristics of the current signal transmission in seawater with transmission frequencies ranging from 30 kHz to 1 MHz,and transmission distances in the vertical range of 4 m.The COMSOL Multiphysics simulation and practical test analysis are carried out to analyze the frequency selectivity of seawater conductivity.It is proved that the seawater resistance increases as the frequency increases,which is the key problem that affects the current signal.This study provides an important theoretical support and experimental evidence for improving the transmission performance of long-distance underwater current signals.
基金supported by National Natural Science foundation of China (Grant Nos. 51371103 and 51231004)National Basic Research Program of China (Grant No. 2010CB832905)+1 种基金National Hi-tech (R&D) Project of China (Grant Nos. 2012AA03A706, 2013AA030801)the Research Project of Chinese Ministry of Education (No. 113007A)
文摘Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-junction, the electrolyte layer handled at high temperature showed nano-fiber microstructures accompanied with greatly improved salt solubility. Ions with high mobility were confined in the nano-fibrous channels leading to the semiconducting polymer layer,which is favorable for modulating dynamic doping at the semiconducting polymer/electrolyte interface by pulse frequency.Such a device realized synaptic-like frequency selectivity, i.e., depression at low frequency stimulation but potentiation at high-frequency stimulation.
文摘In this paper, a new observation equation of non-Gaussian frequency selective fading Bell Labs layered space time （BLAST） architecture system is proposed, which is used for frequency selective fading channels and non-Gaussian noise in an application environment of BLAST system. With othogonal matrix triangularization （QR decomposition） of the channel matrix, the static observation equation of frequency selective fading BLAST system is transformed into a dynamic state space model, and then the particle filter is used for space-time layered detection. Making the full use of the finite alphabet of the digital modulation communication signal, the optimal proposal distribution can be chosen to produce particle and update the weight. Incorporated with current method of reducing error propagation, a new space-time layered detection algorithm is proposed. Simulation result shows the validity of the proposed algorithm.
基金supported by the National Natural Science Foundation of China(90305026).
文摘Traditional multi-band frequency selective surface （FSS） approaches are hard to achieve a perfect resonance response in a wide band due to the limit of the onset grating lobe frequency determined by the array. To solve this problem, an approach of combining elements in different period to build a hybrid array is presented. The results of series of numerical simulation show that multi-periodicity combined element FSS, which are designed using this approach, usually have much weaker grating lobes than the traditional FSS. Furthermore, their frequency response can be well predicted through the properties of their member element FSS. A prediction method for estimating the degree of expected grating lobe energy loss in designing multi-band FSS using this approach is provided.
基金supported by the National Natural Science Foundation of China(41704146)the Fundamental Research Funds for National Universities,China University of Geosciences(Wuhan)(CUGL180816)。
文摘Tunnel seismic detection methods are effective for obtaining the geological structure around the tunnel face,which is critical for safe construction and disaster mitigation in tunnel engineering.However,there is often a lack of accuracy in the acquired geological information and physical properties ahead of the tunnel face in the current tunnel seismic detection methods.Thus,we apply a frequency-domain acoustic full-waveform inversion(FWI)method to obtain high-resolution results for the tunnel structure.We discuss the influence of the frequency group selection strategy and the tunnel observation system settings regarding the inversion results and determine the structural imaging and physical property parameter inversion of abnormal geological bodies ahead of the tunnel face.Based on the conventional strategies of frequency-domain acoustic FWI,we propose a frequency group selection strategy that combines a low-frequency selection covering the vertical wavenumber and a high-frequency selection of antialiasing.This strategy can effectively obtain the spatial structure and physical parameters of the geology ahead of the tunnel face and improve the inversion resolution.In addition,by linearly increasing the side length of the tunnel observation system,we share the influence of the length of the two sides of the observation systems of different tunnels on the inversion results.We found out that the inversion results are the best when the side length is approximately five times the width of the tunnel face,and the influence of increasing the side observation length beyond this range on the inversion results can be ignored.Finally,based on this approach,we invert for the complex multi-stratum model,and an accurate structure and physical property parameters of the complex stratum ahead of the tunnel face are obtained,which verifies the feasibility of the proposed method.
基金Project supported by the National Natural Science Foundations of China (Grant Nos.61271250 and 61202490)
文摘An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loaded receiving antenna array. The existing absorber is effectively simplified by withdrawing half of the loaded resistors; a more compact one is obtained when lumped capacitors are introduced. Building on this, a varactor-tunable absorber with a proper bias network is proposed. Numerical simulations of one tunable absorber with 1.6 mm in thickness show that a wide tuning range from 3.05 GHz to 1.96 GHz is achieved by changing the capacitance of the loaded varactor from 0.5 pF to 5.0 pF. An experiment is carried out using a rectangular waveguide measurement setup and excellent agreement between the simulated and measured results is demonstrated.
基金Project supported by the National Natural Science Foundation of China (Grant No 10647105)
文摘Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm （GA） when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.60990322,60990320,60801001,and 61101011)the Key Grant Project of Ministry of Education of China(Grant No.313029)+1 种基金the Ph.D.Program Foundation of Ministry of Education of China(Grant Nos.20100091110036 and 20120091110032)the Jiangsu Key Laboratory of Advanced Techniques for Manipulating Electromagnetic Waves,China
文摘A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimensional periodic array of substrate integrated waveguide cavities, realizing the polarization rotation by coupling the input signal to the output wave through three metallic slots. Two layers of frequency selective surfaces are cascaded by substrate and form the polarization rotator. A vertical slot on the top layer is used to select the horizontal polarization from the incident wave, the vertical and the horizontal slots on the bottom layer are, respectively, used to obtain horizontally and vertically polarized outgoing waves. The two orthogonal outgoing waves are combined to result in the 45~ polarized wave. Both full wave simulation and experimental measurement are carried out, together validating the proposed method.
