Four different routes of asymmetric reduction rolling were conducted on AZ31 magnesium alloy to investigate their effect on the microstructure evolution and mechanical properties. Route A is the forward rolling; while...Four different routes of asymmetric reduction rolling were conducted on AZ31 magnesium alloy to investigate their effect on the microstructure evolution and mechanical properties. Route A is the forward rolling; while during routes B and C the sheets are rotated 180o in rolling direction and normal direction, respectively; route D is the unidirectional rolling. The strain states of rolled sheets were analyzed by the finite element method, while the microstructure and texture were observed using optical microscopy, X-ray diffraction and electron back-scattered diffraction techniques, and the mechanical properties were measured by tensile test. The results show that route D produced the largest effective strain. Compared with other samples, sample D exhibited a homogeneous microstructure with fine grains as well as a weak and tilted texture, in corresponding, it performed excellent tensile properties, which suggested that route D was an effective way to enhance the strength and plasticity of AZ31 sheet.展开更多
To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback,discomfort in occlusion of the extemal ear canal and so on,implantable middle e...To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback,discomfort in occlusion of the extemal ear canal and so on,implantable middle ear hearing devices(IMEHDs)have been developed over the past two decades.For such kinds of IMEHDs,this paper presents the design of a floating mass piezoelectric actuator using a PMN-30%PT stack as a new type of vibrator.The proposed piezoelectric actuator consists of only three components of a piezoelectric stack,a metal case and a clamp.For the purpose of aiding the design of this actuator,a coupling biomechanics model of human middle ear and the piezoelectric actuator was constructed.This model was built based on a complete set of computerized tomography section images of a healthy volunteer's left ear by reverse engineering technology.The validity of this model was confirmed by comparing the motion of the tympanic membrane and stapes footplate obtained by this model with published experimental measurements on human temporal bones.It is shown that the designed actuator can be implanted on the incus long process by a simple surgical operation,and the stapes footplate displacement by its excitation at 10.5 V root-mean-square(RMS)voltage was equivalent to that from acoustic stimulation at 100 dB sound pressure level(SPL),which is adequate stimulation to the ossicular chain.The corresponding power consumption is 0.04 mW per volt of excitation at 1 kHz,which is low enough for the transducer to be used in an implantable middle ear device.展开更多
基金Project(51471041)supported by the National Natural Science Foundation of China
文摘Four different routes of asymmetric reduction rolling were conducted on AZ31 magnesium alloy to investigate their effect on the microstructure evolution and mechanical properties. Route A is the forward rolling; while during routes B and C the sheets are rotated 180o in rolling direction and normal direction, respectively; route D is the unidirectional rolling. The strain states of rolled sheets were analyzed by the finite element method, while the microstructure and texture were observed using optical microscopy, X-ray diffraction and electron back-scattered diffraction techniques, and the mechanical properties were measured by tensile test. The results show that route D produced the largest effective strain. Compared with other samples, sample D exhibited a homogeneous microstructure with fine grains as well as a weak and tilted texture, in corresponding, it performed excellent tensile properties, which suggested that route D was an effective way to enhance the strength and plasticity of AZ31 sheet.
基金supported by National Natural Science Foundation of China(Grant No.10772121)
文摘To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback,discomfort in occlusion of the extemal ear canal and so on,implantable middle ear hearing devices(IMEHDs)have been developed over the past two decades.For such kinds of IMEHDs,this paper presents the design of a floating mass piezoelectric actuator using a PMN-30%PT stack as a new type of vibrator.The proposed piezoelectric actuator consists of only three components of a piezoelectric stack,a metal case and a clamp.For the purpose of aiding the design of this actuator,a coupling biomechanics model of human middle ear and the piezoelectric actuator was constructed.This model was built based on a complete set of computerized tomography section images of a healthy volunteer's left ear by reverse engineering technology.The validity of this model was confirmed by comparing the motion of the tympanic membrane and stapes footplate obtained by this model with published experimental measurements on human temporal bones.It is shown that the designed actuator can be implanted on the incus long process by a simple surgical operation,and the stapes footplate displacement by its excitation at 10.5 V root-mean-square(RMS)voltage was equivalent to that from acoustic stimulation at 100 dB sound pressure level(SPL),which is adequate stimulation to the ossicular chain.The corresponding power consumption is 0.04 mW per volt of excitation at 1 kHz,which is low enough for the transducer to be used in an implantable middle ear device.
