In this study,we design and numerically investigate a novel all optical D flip-flop(AODFF)based on linear photonic crystal(LPhC)structure that is composed of optical waveguides using the finite difference time domain(...In this study,we design and numerically investigate a novel all optical D flip-flop(AODFF)based on linear photonic crystal(LPhC)structure that is composed of optical waveguides using the finite difference time domain(FDTD)method.The proposed structure has the hexagonal close packed of 16×20 circular rods that are suspended in the air substrate with a lattice constant of 606 nm.The plane wave expansion(PWE)method is used to obtain the band diagram for AODFF at an operating wavelength of 1550 nm.The proposed optical flip-flop achieves a low delay time of 0.2 ps and a high contrast ratio(CR)of 10.33 dB.The main advantage of this design is that the input power as low as 1 mW/μm^(2) is sufficient for its operation,since no nonlinear rods are included.In addition,the footprint of the proposed AODFF is 100μm^(2),which is smaller compared to the structures reported in the literature,and it has a fast switching frequency of 5 Tbit/s.展开更多
This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operatin...This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operating principle and structure of the sensor. And noise effect on characteristics of the sensor is analysed in detail. The modulated effect of the triangular wave voltage is quantified. As an example, an integrated pressure sensor is introduced and the experimental results agree with the theoretical analyses.展开更多
A novel general purpose sense amplifier based flip flop is proposed.Compared to other flip flops,the proposed flip flop has faster operating speed under the approximately same power consumption,and needs fewer tr...A novel general purpose sense amplifier based flip flop is proposed.Compared to other flip flops,the proposed flip flop has faster operating speed under the approximately same power consumption,and needs fewer transistors and consumes smaller area.Moreover,it eliminates the glitch problem.By using pseudo PMOS dynamic technique,its performance is further improved.展开更多
By using the theory of clipping voltage-switches, two kinds of master/slave nMOS quaternary flip-flops are designed. These flip-flops have the capability of two-input presetting and double-rail complementary outputs. ...By using the theory of clipping voltage-switches, two kinds of master/slave nMOS quaternary flip-flops are designed. These flip-flops have the capability of two-input presetting and double-rail complementary outputs. It is shown that these flip-flops are effectively suitable to design nMOS quaternary sequential circuits by designing two examples of hexadecimal up-counter and decimal up-counter.展开更多
This research deals with the oscillation mechanism of a flip-flop jet nozzle with a connecting tube, based on the measurements of pressures and velocities in the connecting tube and inside the nozzle. The measurements...This research deals with the oscillation mechanism of a flip-flop jet nozzle with a connecting tube, based on the measurements of pressures and velocities in the connecting tube and inside the nozzle. The measurements are carried out varying: 1) the inside diameter d of the connecting tube;2) the length L of the connecting tube and 3) the jet velocity VPN from a primary-nozzle exit. We assume that the jet switches when a time integral reaches a certain value. At first, as the time integral, we introduce the accumulated flow work of pressure, namely, the time integral of mass flux through a connecting tube into the jet-reattaching wall from the opposite jet-un-reattaching wall. Under the assumption, the trace of pressure difference between both the ends of the connecting tube is simply modeled on the basis of measurements, and the flow velocity in the connecting tube is computed as incompressible flow. Second, in order to discuss the physics of the accumulated flow work further, we conduct another experiment in single-port control where the inflow from the control port on the jet-reattaching wall is forcibly controlled and the other control port on the opposite jet-un-reattaching wall is sealed, instead of the experiment in regular jet’s oscillation using the ordinary nozzle with two control ports in connection. As a result, it is found that the accumulated flow work is adequate to determine the dominant jet- oscillation frequency. In the experiment in single-port control, the accumulated flow work of the inflow until the jet’s switching well agrees with that in regular jet’s oscillation using the ordinary nozzle.展开更多
According to the next-state equations of various ternary flip-flops(tri-flop),whichare based upon ternary modular algebra,various ternary flip-flops are implemented by usinguniversal-logic-modules,U_hs.Based on it,ter...According to the next-state equations of various ternary flip-flops(tri-flop),whichare based upon ternary modular algebra,various ternary flip-flops are implemented by usinguniversal-logic-modules,U_hs.Based on it,ternary sequential circuits are implemented by usingarray of universal-logic-modules,U_hs.展开更多
As technology scales down, clock distribution networks(CDNs) in integrated circuits(ICs) are becoming increasingly sensitive to single-event transients(SETs).The SET occurring in the CDN can even lead to failure of th...As technology scales down, clock distribution networks(CDNs) in integrated circuits(ICs) are becoming increasingly sensitive to single-event transients(SETs).The SET occurring in the CDN can even lead to failure of the entire circuit system. Understanding the factors that influence the SET sensitivity of the CDN is crucial to achieving radiation hardening of the CDN and realizing the design of highly reliable ICs. In this paper, the influences of different sequential elements(D-flip-flops and D-latches, the two most commonly used sequential elements in modern synchronous digital systems) on the SET susceptibility of the CDN were quantitatively studied. Electrical simulation and heavy ion experiment results reveal that the CDN-SET-induced incorrect latching is much more likely to occur in DFF and DFF-based designs. This can supply guidelines for the design of IC with high reliability.展开更多
The design of ternary edge-triggered JKL-type flip-flop is proposed.The computersimulation and the test in experimental circuit made up with TTL gate show this flip-flop has theexpected logic functions.
Low power consumption is a major issue in nowadays electronics systems. This trend is pushed by the development of data center related to cloud services and soon to the Internet of Things （IoT） deployment. Memories ...Low power consumption is a major issue in nowadays electronics systems. This trend is pushed by the development of data center related to cloud services and soon to the Internet of Things （IoT） deployment. Memories are one of the major contributors to power consumption. However, the development of emerging memory technologies paves the way to low-power design, through the partial replacement of the dynamic random access memory （DRAM） with the non-volatile stand-alone memory in servers or with the embedded or distributed emerging non-volatile memory in IoT objects. In the latter case, non-volatile flip-flops （NVFFs） seem a promising candidate to replace the retention latch. Indeed, IoT objects present long sleep time and NVFFs offer to save data in registers with zero power when the application is idle. This paper gives an overview of NVFF architecture flavors for various emerging memory technologies.展开更多
The flow visualization work with the aid of PIV and Piezometer deals with flip-flop flow around diamond-shaped cylinder bundle revised with concavities on both bundle walls. It is disclosed that 1) the concavity const...The flow visualization work with the aid of PIV and Piezometer deals with flip-flop flow around diamond-shaped cylinder bundle revised with concavities on both bundle walls. It is disclosed that 1) the concavity constructed on both side-walls of a diamond cylinder induces a substantial change in the flow patterns in the exit jet-stream field and jet- stream dispersion, 2) pressure characteristics are quantitatively measured in a diverging-flow region in diamond cylinder bundles with concavityand in its downstream region, and 3) flip-flop flow occurs in the flow passages and its occurrence condition is obtained.展开更多
A new all optical flip-flop based on a 3-sections nonlinear semiconductor DFB laser structure is proposed and simulated. The operation of the device does not require a holding beam. Electrical current injection into a...A new all optical flip-flop based on a 3-sections nonlinear semiconductor DFB laser structure is proposed and simulated. The operation of the device does not require a holding beam. Electrical current injection into an active layer provides optical gain to the laser mode. The wave-guiding layer consists of a linear grating section centered between 2 detuned nonlinear grating sections. The average refractive index in the nonlinear sections is slightly higher than the refractive index of the middle section. A negative nonlinear refractive index coefficient exists along the nonlinear sections. In the “OFF” state, the DFB structure does not provide enough optical feedback to lase due to the detuned sections. At high light intensity in structure, “ON” state, detuning decreases and the DFB structure allows for a laser mode that sustains the decrease in detuning to exist. The nonlinearity is provided by direct photon absorption at the Urbach tail. Numerical simulations using GPGPU computing show nanoseconds transition times between “OFF” and “ON” states.展开更多
A new all-optical flip-flop based on a nonlinear Distributed feedback (DFB) structure is proposed. The device does not require a holding beam. A nonlinear part of the grating is detuned from the remaining part of the ...A new all-optical flip-flop based on a nonlinear Distributed feedback (DFB) structure is proposed. The device does not require a holding beam. A nonlinear part of the grating is detuned from the remaining part of the grating and has negative nonlinear coefficient. Optical gain is provided by an injected electrical current into an active layer. In the OFF state, due to the detuned section, no laser light is generated in the device. An injected optical pulse reduces the detuning of the nonlinear section, and the optical feedback provided by the DFB structure generates a laser light in the structure that sustains the change in the detuned section. The device is switched “OFF” by detuning another section of the grating by a Reset pulse. The Reset pulse reduces the refractive index of that section by the generation of electron-hole pairs. The Reset pulse wavelength is adjusted such that the optical gain provided by the active layer at that wavelength is zero. The Reset pulse is prevented from reaching the nonlinear detuned section by introducing an optical absorber in the laser cavity to attenuate the pulse. The device is simulated in time domain using General Purpose Graphics Processing Unit (GPGPU) computing. Set-Reset operations are in nanosecond time scale.展开更多
A new design for an all optical flip flop is introduced. It is based on a nonlinear Distributed Bragg Reflector (DBR) semiconductor laser structure. The device does not require a holding beam. An optical gain medium c...A new design for an all optical flip flop is introduced. It is based on a nonlinear Distributed Bragg Reflector (DBR) semiconductor laser structure. The device does not require a holding beam. An optical gain medium confined between 2 Bragg reflectors forms the device. One of the Bragg reflectors is detuned from the other by making its average refractive index slightly higher, and it has a negative nonlinear coefficient that is due to direct absorption at Urbach tail. At low light intensity in the structure, the detuned Bragg reflector does not provide optical feedback to start a laser mode. An optical pulse injected to the structure reduces the detuning of the nonlinear Bragg reflector and a laser mode builds up. The device is reset by detuning the second Bragg reflector optically by an optical pulse that generates electron-hole pairs by direct absorption. A mathematical model of the device is introduced. The model is solved numerically in time domain using a general purpose graphics processing unit (GPGPU) to increase accuracy and to reduce the computation time. The switching dynamics of the device are in nanosecond time scale. The device could be used for all optical data packet switching/routing.展开更多
The problems existing in the binary logic system and the advantages of multiple-valued logic (MVL) are introduced. A literal circuit with three-track-output structure is created based on resonant tunneling diodes (RTD...The problems existing in the binary logic system and the advantages of multiple-valued logic (MVL) are introduced. A literal circuit with three-track-output structure is created based on resonant tunneling diodes (RTDs) and it has the most basic memory function. A ternary RTD D flip-flop with pre-set and pre-reset functions is also designed, the key module of which is the RTD literal circuit. Two types of output structure of the ternary RTD D flip-flop are optional: one is three-track and the other is single-track; these two structures can be transformed conveniently by merely adding tri-valued RTD NAND, NOR, and inverter units after the three-track output. The design is verified by simulation. Ternary flip-flop consists of an RTD literal circuit and it not only is easy to understand and implement but also provides a solution for the algebraic interface between the multiple-valued logic and the binary logic. The method can also be used for design of other types of multiple-valued RTD flip-flop circuits.展开更多
Quantum-dot cellular automata (QCA) technology has been widely considered as an alternative to complementary metal-oxide-semiconductor (CMOS) due to QCA's inherent merits.Many interesting QCA-based logic circuits ...Quantum-dot cellular automata (QCA) technology has been widely considered as an alternative to complementary metal-oxide-semiconductor (CMOS) due to QCA's inherent merits.Many interesting QCA-based logic circuits with smaller feature size,higher operating frequency,and lower power consumption than CMOS have been presented.However,QCA is limited in its sequential circuit design with high performance flip-flops.Based on a brief introduction of QCA and dual-edge triggered (DET) flip-flop,we propose two original QCA-based D and JK DET flip-flops,offering the same data throughput of corresponding single-edge triggered (SET) flip-flops at half the clock pulse frequency.The logic functionality of the two proposed flip-flops is verified with the QCADesigner tool.All the proposed QCA-based DET flip-flops show higher performance than their SET counterparts in terms of data throughput.Furthermore,compared with a previous DET D flip-flop,the number of cells,covered area,and time delay of the proposed DET D flip-flop are reduced by 20.5%,23.5%,and 25%,respectively.By using a lower clock pulse frequency,the proposed DET flip-flops are promising for constructing QCA sequential circuits and systems with high performance.展开更多
文摘In this study,we design and numerically investigate a novel all optical D flip-flop(AODFF)based on linear photonic crystal(LPhC)structure that is composed of optical waveguides using the finite difference time domain(FDTD)method.The proposed structure has the hexagonal close packed of 16×20 circular rods that are suspended in the air substrate with a lattice constant of 606 nm.The plane wave expansion(PWE)method is used to obtain the band diagram for AODFF at an operating wavelength of 1550 nm.The proposed optical flip-flop achieves a low delay time of 0.2 ps and a high contrast ratio(CR)of 10.33 dB.The main advantage of this design is that the input power as low as 1 mW/μm^(2) is sufficient for its operation,since no nonlinear rods are included.In addition,the footprint of the proposed AODFF is 100μm^(2),which is smaller compared to the structures reported in the literature,and it has a fast switching frequency of 5 Tbit/s.
文摘This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operating principle and structure of the sensor. And noise effect on characteristics of the sensor is analysed in detail. The modulated effect of the triangular wave voltage is quantified. As an example, an integrated pressure sensor is introduced and the experimental results agree with the theoretical analyses.
文摘A novel general purpose sense amplifier based flip flop is proposed.Compared to other flip flops,the proposed flip flop has faster operating speed under the approximately same power consumption,and needs fewer transistors and consumes smaller area.Moreover,it eliminates the glitch problem.By using pseudo PMOS dynamic technique,its performance is further improved.
基金Suported by Youth Science & Technology Foundation of Ningbo Science & Technology Commission and by Natural Science Foundation of Zhejiang Proyince,China
文摘By using the theory of clipping voltage-switches, two kinds of master/slave nMOS quaternary flip-flops are designed. These flip-flops have the capability of two-input presetting and double-rail complementary outputs. It is shown that these flip-flops are effectively suitable to design nMOS quaternary sequential circuits by designing two examples of hexadecimal up-counter and decimal up-counter.
文摘This research deals with the oscillation mechanism of a flip-flop jet nozzle with a connecting tube, based on the measurements of pressures and velocities in the connecting tube and inside the nozzle. The measurements are carried out varying: 1) the inside diameter d of the connecting tube;2) the length L of the connecting tube and 3) the jet velocity VPN from a primary-nozzle exit. We assume that the jet switches when a time integral reaches a certain value. At first, as the time integral, we introduce the accumulated flow work of pressure, namely, the time integral of mass flux through a connecting tube into the jet-reattaching wall from the opposite jet-un-reattaching wall. Under the assumption, the trace of pressure difference between both the ends of the connecting tube is simply modeled on the basis of measurements, and the flow velocity in the connecting tube is computed as incompressible flow. Second, in order to discuss the physics of the accumulated flow work further, we conduct another experiment in single-port control where the inflow from the control port on the jet-reattaching wall is forcibly controlled and the other control port on the opposite jet-un-reattaching wall is sealed, instead of the experiment in regular jet’s oscillation using the ordinary nozzle with two control ports in connection. As a result, it is found that the accumulated flow work is adequate to determine the dominant jet- oscillation frequency. In the experiment in single-port control, the accumulated flow work of the inflow until the jet’s switching well agrees with that in regular jet’s oscillation using the ordinary nozzle.
基金Supported by the National Natural Science Foundation of Zhejiang Province,China.
文摘According to the next-state equations of various ternary flip-flops(tri-flop),whichare based upon ternary modular algebra,various ternary flip-flops are implemented by usinguniversal-logic-modules,U_hs.Based on it,ternary sequential circuits are implemented by usingarray of universal-logic-modules,U_hs.
基金supported by the National Natural Science Foundation of China(No.61434007)the National Natural Science Foundation of China(No.61704192)
文摘As technology scales down, clock distribution networks(CDNs) in integrated circuits(ICs) are becoming increasingly sensitive to single-event transients(SETs).The SET occurring in the CDN can even lead to failure of the entire circuit system. Understanding the factors that influence the SET sensitivity of the CDN is crucial to achieving radiation hardening of the CDN and realizing the design of highly reliable ICs. In this paper, the influences of different sequential elements(D-flip-flops and D-latches, the two most commonly used sequential elements in modern synchronous digital systems) on the SET susceptibility of the CDN were quantitatively studied. Electrical simulation and heavy ion experiment results reveal that the CDN-SET-induced incorrect latching is much more likely to occur in DFF and DFF-based designs. This can supply guidelines for the design of IC with high reliability.
基金The Project Supported by National Natural Science Foundation of China
文摘The design of ternary edge-triggered JKL-type flip-flop is proposed.The computersimulation and the test in experimental circuit made up with TTL gate show this flip-flop has theexpected logic functions.
基金supported by the ANR project DIPMEM under Grant No.ANR-12-NANO-0010-04
文摘Low power consumption is a major issue in nowadays electronics systems. This trend is pushed by the development of data center related to cloud services and soon to the Internet of Things （IoT） deployment. Memories are one of the major contributors to power consumption. However, the development of emerging memory technologies paves the way to low-power design, through the partial replacement of the dynamic random access memory （DRAM） with the non-volatile stand-alone memory in servers or with the embedded or distributed emerging non-volatile memory in IoT objects. In the latter case, non-volatile flip-flops （NVFFs） seem a promising candidate to replace the retention latch. Indeed, IoT objects present long sleep time and NVFFs offer to save data in registers with zero power when the application is idle. This paper gives an overview of NVFF architecture flavors for various emerging memory technologies.
文摘The flow visualization work with the aid of PIV and Piezometer deals with flip-flop flow around diamond-shaped cylinder bundle revised with concavities on both bundle walls. It is disclosed that 1) the concavity constructed on both side-walls of a diamond cylinder induces a substantial change in the flow patterns in the exit jet-stream field and jet- stream dispersion, 2) pressure characteristics are quantitatively measured in a diverging-flow region in diamond cylinder bundles with concavityand in its downstream region, and 3) flip-flop flow occurs in the flow passages and its occurrence condition is obtained.
文摘A new all optical flip-flop based on a 3-sections nonlinear semiconductor DFB laser structure is proposed and simulated. The operation of the device does not require a holding beam. Electrical current injection into an active layer provides optical gain to the laser mode. The wave-guiding layer consists of a linear grating section centered between 2 detuned nonlinear grating sections. The average refractive index in the nonlinear sections is slightly higher than the refractive index of the middle section. A negative nonlinear refractive index coefficient exists along the nonlinear sections. In the “OFF” state, the DFB structure does not provide enough optical feedback to lase due to the detuned sections. At high light intensity in structure, “ON” state, detuning decreases and the DFB structure allows for a laser mode that sustains the decrease in detuning to exist. The nonlinearity is provided by direct photon absorption at the Urbach tail. Numerical simulations using GPGPU computing show nanoseconds transition times between “OFF” and “ON” states.
文摘A new all-optical flip-flop based on a nonlinear Distributed feedback (DFB) structure is proposed. The device does not require a holding beam. A nonlinear part of the grating is detuned from the remaining part of the grating and has negative nonlinear coefficient. Optical gain is provided by an injected electrical current into an active layer. In the OFF state, due to the detuned section, no laser light is generated in the device. An injected optical pulse reduces the detuning of the nonlinear section, and the optical feedback provided by the DFB structure generates a laser light in the structure that sustains the change in the detuned section. The device is switched “OFF” by detuning another section of the grating by a Reset pulse. The Reset pulse reduces the refractive index of that section by the generation of electron-hole pairs. The Reset pulse wavelength is adjusted such that the optical gain provided by the active layer at that wavelength is zero. The Reset pulse is prevented from reaching the nonlinear detuned section by introducing an optical absorber in the laser cavity to attenuate the pulse. The device is simulated in time domain using General Purpose Graphics Processing Unit (GPGPU) computing. Set-Reset operations are in nanosecond time scale.
文摘A new design for an all optical flip flop is introduced. It is based on a nonlinear Distributed Bragg Reflector (DBR) semiconductor laser structure. The device does not require a holding beam. An optical gain medium confined between 2 Bragg reflectors forms the device. One of the Bragg reflectors is detuned from the other by making its average refractive index slightly higher, and it has a negative nonlinear coefficient that is due to direct absorption at Urbach tail. At low light intensity in the structure, the detuned Bragg reflector does not provide optical feedback to start a laser mode. An optical pulse injected to the structure reduces the detuning of the nonlinear Bragg reflector and a laser mode builds up. The device is reset by detuning the second Bragg reflector optically by an optical pulse that generates electron-hole pairs by direct absorption. A mathematical model of the device is introduced. The model is solved numerically in time domain using a general purpose graphics processing unit (GPGPU) to increase accuracy and to reduce the computation time. The switching dynamics of the device are in nanosecond time scale. The device could be used for all optical data packet switching/routing.
文摘The problems existing in the binary logic system and the advantages of multiple-valued logic (MVL) are introduced. A literal circuit with three-track-output structure is created based on resonant tunneling diodes (RTDs) and it has the most basic memory function. A ternary RTD D flip-flop with pre-set and pre-reset functions is also designed, the key module of which is the RTD literal circuit. Two types of output structure of the ternary RTD D flip-flop are optional: one is three-track and the other is single-track; these two structures can be transformed conveniently by merely adding tri-valued RTD NAND, NOR, and inverter units after the three-track output. The design is verified by simulation. Ternary flip-flop consists of an RTD literal circuit and it not only is easy to understand and implement but also provides a solution for the algebraic interface between the multiple-valued logic and the binary logic. The method can also be used for design of other types of multiple-valued RTD flip-flop circuits.
基金Project (No.Y1110808) supported by the Natural Science Foundation of Zhejiang Province,China
文摘Quantum-dot cellular automata (QCA) technology has been widely considered as an alternative to complementary metal-oxide-semiconductor (CMOS) due to QCA's inherent merits.Many interesting QCA-based logic circuits with smaller feature size,higher operating frequency,and lower power consumption than CMOS have been presented.However,QCA is limited in its sequential circuit design with high performance flip-flops.Based on a brief introduction of QCA and dual-edge triggered (DET) flip-flop,we propose two original QCA-based D and JK DET flip-flops,offering the same data throughput of corresponding single-edge triggered (SET) flip-flops at half the clock pulse frequency.The logic functionality of the two proposed flip-flops is verified with the QCADesigner tool.All the proposed QCA-based DET flip-flops show higher performance than their SET counterparts in terms of data throughput.Furthermore,compared with a previous DET D flip-flop,the number of cells,covered area,and time delay of the proposed DET D flip-flop are reduced by 20.5%,23.5%,and 25%,respectively.By using a lower clock pulse frequency,the proposed DET flip-flops are promising for constructing QCA sequential circuits and systems with high performance.
