[Objective]This study aims to investigate the multi-body hydrodynamic interaction mechanisms during offshore lifting operations of aquaculture net cages in wind-fishery integration systems.By integrating numerical sim...[Objective]This study aims to investigate the multi-body hydrodynamic interaction mechanisms during offshore lifting operations of aquaculture net cages in wind-fishery integration systems.By integrating numerical simulations and dynamic analysis methods,this study systematically investigates the coupled dynamic response characteristics during the cage-carrier vessel separation process to reveal its dynamic evolution patterns and key influence mechanisms.[Method]Based on potential flow theory,a fully coupled dynamic analysis model of crane vessel-net cage-semi-submersible barge was established for a marine ranch project in Guangdong.The complete lifting process was dynamically simulated using SESAM software.Five typical operating sea states were configured to investigate the influence of wave parameters on the system's motion response under combined wave-current-wind actions.[Result]The results demonstrate that wave period dominates the system stability.Under short-period conditions,the system maintains stable motion with relatively small horizontal relative displacements,while long-period conditions excite low-frequency resonance,leading to significant slow-drift motions.Vertical response analysis reveals that long-period waves cause severe relative displacement fluctuations between the cage and semi-submersible vessel,with actual displacement amplitudes doubling the preset safety target of 2.045 m.Quantitative analysis further indicates that when significant wave height increases from 1.0 m to 1.5 m,the actual displacement amplitude increases by approximately 20%relative to the target displacement of 2.045 m,demonstrating that its influence is significantly weaker than the displacement variations induced by wave period changes.The complete dynamic simulation successfully captures the continuous dynamic response characteristics during the lifting process.[Conclusion]This research clarifies the influence mechanisms of wave parameters on the cage lifting process,identifying wave period as the crucial factor for operational safety.An operation window assessment method incorporating multi-body coupling effects is established,proposing a safety criterion with peak period not exceeding six seconds as the core requirement.The findings provide theoretical foundation for safe installation of marine ranch net cages and offer valuable references for similar offshore lifting operations.展开更多
A new hybrid method of frequency domain and time domain is developed in this paper to predict the motion responses of a flexibly joint multi-body floating system to irregular waves. The main idea of the method is that...A new hybrid method of frequency domain and time domain is developed in this paper to predict the motion responses of a flexibly joint multi-body floating system to irregular waves. The main idea of the method is that the three-dimensional frequency method is used to obtain the hydrodynamic coefficients and the response equations are solved in time domain step by step. All the forces can be obtained at the same time. The motions and nonlinear mooring forces of a box type six-body floating system are predicted. A comparison of the theoretical method-based Solutions with experimental results has shown good agreement.展开更多
The dynamics, stability and control problem of a kind of infinite dimensional system are studied in the functional space with the method of modern Mathematics. First, the dynamical control model of the distributed par...The dynamics, stability and control problem of a kind of infinite dimensional system are studied in the functional space with the method of modern Mathematics. First, the dynamical control model of the distributed parameter system with multi-body flexible and multi-topological structure was established which has damping, gyroscopic parts and constrained damping. Secondly, the necessary and sufficient condition of controllability and observability, the stability theory and asymptotic property of the system were obtained. These results expand the theory of the field about the dynamics and control of the system with multi-body flexible structure, and have important engineering significance.展开更多
The objective of this investigation is to examine the correctness and efficiency of the choice of boundary conditions when using assumed mode approach to simulate flexible multi-body systems. The displacement field du...The objective of this investigation is to examine the correctness and efficiency of the choice of boundary conditions when using assumed mode approach to simulate flexible multi-body systems. The displacement field due to deformation is approximated by the Rayleigh-Ritz assumed modes in floating frame of reference （FFR） formulation. The deformations obtained by the absolute nodal coordinate （ANC） formulation which are transformed by two sets of reference coordinates are introduced as a criterion to verify the accuracy of the simulation results by using the FFR formulation. The relationship between the deformations obtained from different boundary conditions is revealed. Nu- merical simulation examples demonstrate that the assumed modes with cantilevered-free, simply-supported and free- free boundary conditions without inclusion of rigid body modes are suitable for simulation of flexible multi-body system with large over all motion, and the same physical deformation can be obtained using those mode functions, differ only by a coordinate transformation. It is also shown that when using mode shapes with statically indeterminate boundary conditions, significant error may occur. Furthermore, the slider crank mechanism with rigid crank is accurate enough for investigating boundary condition problem of flexible multi-body system, which cost significant less simulating time.展开更多
In this paper,an efficien formulation based on the Lagrangian method is presented to investigate the contact–impact problems of f exible multi-body systems.Generally,the penalty method and the Hertz contact law are t...In this paper,an efficien formulation based on the Lagrangian method is presented to investigate the contact–impact problems of f exible multi-body systems.Generally,the penalty method and the Hertz contact law are the most commonly used methods in engineering applications.However,these methods are highly dependent on various non-physical parameters,which have great effects on the simulation results.Moreover,a tremendous number of degrees of freedom in the contact–impact problems will influenc thenumericalefficien ysignificantl.Withtheconsideration of these two problems,a formulation combining the component mode synthesis method and the Lagrangian method is presented to investigate the contact–impact problems in fl xible multi-body system numerically.Meanwhile,the finit element meshing laws of the contact bodies will be studied preliminarily.A numerical example with experimental verificatio will certify the reliability of the presented formulationincontact–impactanalysis.Furthermore,aseries of numerical investigations explain how great the influenc of the finit element meshing has on the simulation results.Finally the limitations of the element size in different regions are summarized to satisfy both the accuracy and efficien y.展开更多
The multi-body flexible morphing airfoil can improve the aerodynamic characteristics based on different flight missions continuously.Recently researches have focused on the unsteady aerodynamic characteristics of flex...The multi-body flexible morphing airfoil can improve the aerodynamic characteristics based on different flight missions continuously.Recently researches have focused on the unsteady aerodynamic characteristics of flexible wings under passive actuation.However,the unsteady aerodynamic characteristics with the fluid-structure interaction effects in the multi-body active actuation process of morphing airfoil deserve further investigation.In this paper,a fluid-structure coupled simulation method for multi-body flexible morphing airfoil with active actuation subsystem was investigated,and the aerodynamic characteristics during deformation were compared with different skin flexibility,flow field environment,actuation mode and actuation time.The numerical results show that for the steady aerodynamic,the skin flexibility can improve the stability efficiency.In the unsteady process,the change trend of the transient lift coefficient and pitching moment are consistent with those of the active drive characteristics,while the instantaneous lift-drag ratio coefficient is greatly affected by the driving mode and can be improved by increasing the driving duration.展开更多
The dynamic performance of composite flexible multi-body system under the simultaneous action of thermal fields and driving constraint is analyzed. Based on strain-displacement relation of the Mindlin plate theory whi...The dynamic performance of composite flexible multi-body system under the simultaneous action of thermal fields and driving constraint is analyzed. Based on strain-displacement relation of the Mindlin plate theory which includes transverse shear deformation, and considering thermal effect, variation equations of laminated plate are derived by the principle of virtual work. The finite element method is used for discretization. According to kinematics constraint relation, dynamic equations for spatial slider-crank system are established. Simulation results show that spatial deformation （torsion deformation） appears in the multi-layered composite slider-crank mechanism which is simulated with planar motions. Furthermore, the influence of coupling between thermal expansion and flexible deformations of non-symmetrical composite plates on the large overall motion under the uniform temperature field is investigated. Finally, significant change in constraint force due to the spatial deformation is shown.展开更多
The discontinuous nature of rock cutting can easily cause unwanted vibrations in the structure of a surface miner.If these vibrations are not properly addressed,the related stress cycles can gradually damage the chass...The discontinuous nature of rock cutting can easily cause unwanted vibrations in the structure of a surface miner.If these vibrations are not properly addressed,the related stress cycles can gradually damage the chassis resulting in fatigue failures.These events can seriously undermine the safety of operators and digging operations may be stopped for days,with an obvious economic impact.This work presents an analysis of the dynamics of a surface miner,focusing on the interaction between cutting machine dynamics and cutting forces,which is a new approach for this type of machine.For this purpose,the authors developed a numerical model of the cutting process made up of(1)a multi-body model of the cutting machine,which takes into account the chassis's flexibility;(2)a model of the rotating cutting head;and(3)a model of the interaction between the cutting head and rock,based on Shao's model.The model was compared with experimental results and then used to investigate the effects of cutting speed and cutting depth on the machine dynamics.展开更多
A multi-body model of engine system with flexible crankshaft was presented in this paper to analyze the dynamic behavior of an internal combustion engine. The flexible crankshaft structural dynamics was coupled with t...A multi-body model of engine system with flexible crankshaft was presented in this paper to analyze the dynamic behavior of an internal combustion engine. The flexible crankshaft structural dynamics was coupled with the main beating hydrodynamic lubrication in this model by a system approach. An application of an 14 engine was given to show this sophisticated simulation model and to predict the loads and the orbit plots in the journal beatings by the dynamic response of the multi-body engine system with flexible crankshaft. The numerical results show the capabilities and significance of the flexible crankshaft in this system. The objective of the research is to provide the scientific guidance for design and maintenance of the internal combustion engine.展开更多
In lifting sub-system of deep-sea mining system, spherical joint is used to connect lifting pipes to replace fixed joint. Based on Dynamics of Flexible Multi-body systems, the mechanics model of articulated lifting sy...In lifting sub-system of deep-sea mining system, spherical joint is used to connect lifting pipes to replace fixed joint. Based on Dynamics of Flexible Multi-body systems, the mechanics model of articulated lifting system is established. Under the four-grade and six-grade oceanic condition, dynamic responses of lifting system are simulated and experiment verified. The simulation results are consistent with experimental ones. The maximum moment of flexion is 322 kN-m on the first pipe under six-grade sea condition. It is seen that the articulated connection can reduce the moment of flexion. The bending deformation of pipe center is researched, and the maximum is 0. 000479 m on the first pipe. Deformation has a little effect on the motion of system. It is feasible to analyze articulated lifting system by applying the theory of flexible multi-body dynamics. The articulated lifting system is obviously better than the fixed one.展开更多
文摘[Objective]This study aims to investigate the multi-body hydrodynamic interaction mechanisms during offshore lifting operations of aquaculture net cages in wind-fishery integration systems.By integrating numerical simulations and dynamic analysis methods,this study systematically investigates the coupled dynamic response characteristics during the cage-carrier vessel separation process to reveal its dynamic evolution patterns and key influence mechanisms.[Method]Based on potential flow theory,a fully coupled dynamic analysis model of crane vessel-net cage-semi-submersible barge was established for a marine ranch project in Guangdong.The complete lifting process was dynamically simulated using SESAM software.Five typical operating sea states were configured to investigate the influence of wave parameters on the system's motion response under combined wave-current-wind actions.[Result]The results demonstrate that wave period dominates the system stability.Under short-period conditions,the system maintains stable motion with relatively small horizontal relative displacements,while long-period conditions excite low-frequency resonance,leading to significant slow-drift motions.Vertical response analysis reveals that long-period waves cause severe relative displacement fluctuations between the cage and semi-submersible vessel,with actual displacement amplitudes doubling the preset safety target of 2.045 m.Quantitative analysis further indicates that when significant wave height increases from 1.0 m to 1.5 m,the actual displacement amplitude increases by approximately 20%relative to the target displacement of 2.045 m,demonstrating that its influence is significantly weaker than the displacement variations induced by wave period changes.The complete dynamic simulation successfully captures the continuous dynamic response characteristics during the lifting process.[Conclusion]This research clarifies the influence mechanisms of wave parameters on the cage lifting process,identifying wave period as the crucial factor for operational safety.An operation window assessment method incorporating multi-body coupling effects is established,proposing a safety criterion with peak period not exceeding six seconds as the core requirement.The findings provide theoretical foundation for safe installation of marine ranch net cages and offer valuable references for similar offshore lifting operations.
基金This project was supported by the National Natural Science Foundation of China (Grant No. 50039010)
文摘A new hybrid method of frequency domain and time domain is developed in this paper to predict the motion responses of a flexibly joint multi-body floating system to irregular waves. The main idea of the method is that the three-dimensional frequency method is used to obtain the hydrodynamic coefficients and the response equations are solved in time domain step by step. All the forces can be obtained at the same time. The motions and nonlinear mooring forces of a box type six-body floating system are predicted. A comparison of the theoretical method-based Solutions with experimental results has shown good agreement.
文摘The dynamics, stability and control problem of a kind of infinite dimensional system are studied in the functional space with the method of modern Mathematics. First, the dynamical control model of the distributed parameter system with multi-body flexible and multi-topological structure was established which has damping, gyroscopic parts and constrained damping. Secondly, the necessary and sufficient condition of controllability and observability, the stability theory and asymptotic property of the system were obtained. These results expand the theory of the field about the dynamics and control of the system with multi-body flexible structure, and have important engineering significance.
基金supported by the National Natural Science Foundation of China (10872126)the Research Fund of the Doctoral Program of Higher Education of China (20100073110007)
文摘The objective of this investigation is to examine the correctness and efficiency of the choice of boundary conditions when using assumed mode approach to simulate flexible multi-body systems. The displacement field due to deformation is approximated by the Rayleigh-Ritz assumed modes in floating frame of reference （FFR） formulation. The deformations obtained by the absolute nodal coordinate （ANC） formulation which are transformed by two sets of reference coordinates are introduced as a criterion to verify the accuracy of the simulation results by using the FFR formulation. The relationship between the deformations obtained from different boundary conditions is revealed. Nu- merical simulation examples demonstrate that the assumed modes with cantilevered-free, simply-supported and free- free boundary conditions without inclusion of rigid body modes are suitable for simulation of flexible multi-body system with large over all motion, and the same physical deformation can be obtained using those mode functions, differ only by a coordinate transformation. It is also shown that when using mode shapes with statically indeterminate boundary conditions, significant error may occur. Furthermore, the slider crank mechanism with rigid crank is accurate enough for investigating boundary condition problem of flexible multi-body system, which cost significant less simulating time.
基金supported by the National Science Foundation of China (Grants 11132007,11272203)
文摘In this paper,an efficien formulation based on the Lagrangian method is presented to investigate the contact–impact problems of f exible multi-body systems.Generally,the penalty method and the Hertz contact law are the most commonly used methods in engineering applications.However,these methods are highly dependent on various non-physical parameters,which have great effects on the simulation results.Moreover,a tremendous number of degrees of freedom in the contact–impact problems will influenc thenumericalefficien ysignificantl.Withtheconsideration of these two problems,a formulation combining the component mode synthesis method and the Lagrangian method is presented to investigate the contact–impact problems in fl xible multi-body system numerically.Meanwhile,the finit element meshing laws of the contact bodies will be studied preliminarily.A numerical example with experimental verificatio will certify the reliability of the presented formulationincontact–impactanalysis.Furthermore,aseries of numerical investigations explain how great the influenc of the finit element meshing has on the simulation results.Finally the limitations of the element size in different regions are summarized to satisfy both the accuracy and efficien y.
基金supported by the National Natural Science Foundation of China(Nos.52192633,11872293)the Natural Science Foundation of Shaanxi Province,China(No.2022JC-03)。
文摘The multi-body flexible morphing airfoil can improve the aerodynamic characteristics based on different flight missions continuously.Recently researches have focused on the unsteady aerodynamic characteristics of flexible wings under passive actuation.However,the unsteady aerodynamic characteristics with the fluid-structure interaction effects in the multi-body active actuation process of morphing airfoil deserve further investigation.In this paper,a fluid-structure coupled simulation method for multi-body flexible morphing airfoil with active actuation subsystem was investigated,and the aerodynamic characteristics during deformation were compared with different skin flexibility,flow field environment,actuation mode and actuation time.The numerical results show that for the steady aerodynamic,the skin flexibility can improve the stability efficiency.In the unsteady process,the change trend of the transient lift coefficient and pitching moment are consistent with those of the active drive characteristics,while the instantaneous lift-drag ratio coefficient is greatly affected by the driving mode and can be improved by increasing the driving duration.
基金the National Natural Science Foundation of China(Nos.10872126 and 10772113)
文摘The dynamic performance of composite flexible multi-body system under the simultaneous action of thermal fields and driving constraint is analyzed. Based on strain-displacement relation of the Mindlin plate theory which includes transverse shear deformation, and considering thermal effect, variation equations of laminated plate are derived by the principle of virtual work. The finite element method is used for discretization. According to kinematics constraint relation, dynamic equations for spatial slider-crank system are established. Simulation results show that spatial deformation （torsion deformation） appears in the multi-layered composite slider-crank mechanism which is simulated with planar motions. Furthermore, the influence of coupling between thermal expansion and flexible deformations of non-symmetrical composite plates on the large overall motion under the uniform temperature field is investigated. Finally, significant change in constraint force due to the spatial deformation is shown.
文摘The discontinuous nature of rock cutting can easily cause unwanted vibrations in the structure of a surface miner.If these vibrations are not properly addressed,the related stress cycles can gradually damage the chassis resulting in fatigue failures.These events can seriously undermine the safety of operators and digging operations may be stopped for days,with an obvious economic impact.This work presents an analysis of the dynamics of a surface miner,focusing on the interaction between cutting machine dynamics and cutting forces,which is a new approach for this type of machine.For this purpose,the authors developed a numerical model of the cutting process made up of(1)a multi-body model of the cutting machine,which takes into account the chassis's flexibility;(2)a model of the rotating cutting head;and(3)a model of the interaction between the cutting head and rock,based on Shao's model.The model was compared with experimental results and then used to investigate the effects of cutting speed and cutting depth on the machine dynamics.
基金Project 50375115 supported by the National Natural Science Foundation of China
文摘A multi-body model of engine system with flexible crankshaft was presented in this paper to analyze the dynamic behavior of an internal combustion engine. The flexible crankshaft structural dynamics was coupled with the main beating hydrodynamic lubrication in this model by a system approach. An application of an 14 engine was given to show this sophisticated simulation model and to predict the loads and the orbit plots in the journal beatings by the dynamic response of the multi-body engine system with flexible crankshaft. The numerical results show the capabilities and significance of the flexible crankshaft in this system. The objective of the research is to provide the scientific guidance for design and maintenance of the internal combustion engine.
基金This research project was financially supported by China Ocean Mineral Resources R&D Association(Grant No.DY105-03-02-17)Ph.D.Programs Foundation of Ministry of Education of China(Grant No.20060008025)
文摘In lifting sub-system of deep-sea mining system, spherical joint is used to connect lifting pipes to replace fixed joint. Based on Dynamics of Flexible Multi-body systems, the mechanics model of articulated lifting system is established. Under the four-grade and six-grade oceanic condition, dynamic responses of lifting system are simulated and experiment verified. The simulation results are consistent with experimental ones. The maximum moment of flexion is 322 kN-m on the first pipe under six-grade sea condition. It is seen that the articulated connection can reduce the moment of flexion. The bending deformation of pipe center is researched, and the maximum is 0. 000479 m on the first pipe. Deformation has a little effect on the motion of system. It is feasible to analyze articulated lifting system by applying the theory of flexible multi-body dynamics. The articulated lifting system is obviously better than the fixed one.
