This study delves into both experimental and analytical examinations of heat exchange in a straight channel, where Al_(2)O_(3)-water nanofluids are utilized, spanning the Reynolds number spectrum from 100 to 1800. Div...This study delves into both experimental and analytical examinations of heat exchange in a straight channel, where Al_(2)O_(3)-water nanofluids are utilized, spanning the Reynolds number spectrum from 100 to 1800. Diverse volume fractions(1%, 2%, and 3%) of Al_(2)O_(3)-water nanofluids are meticulously prepared and analyzed. The essential physical properties of these nanofluids, critical for evaluating their thermal and flow characteristics, have been comprehensively assessed. From a quantitative perspective, numerical simulations are employed to predict the Nusselt number(Nu) and friction factor(f). The empirical findings reveal intriguing trends: the friction factor experiences an upward trend with diminishing velocity, attributed to heightened molecular cohesion. Conversely, the friction factor demonstrates a decline with diminishing volume fractions, a consequence of reduced particle size. Both the nanofluid's viscosity and heat transfer coefficient exhibit a rise in tandem with augmented volume flow rate and concentration gradient. Notably, the simulation results harmonize remarkably well with experimental data. Rigorous validation against prior studies underscores the robust consistency of these outcomes. In the pursuit of augmenting heat transfer, a volume fraction of 3% emerges as particularly influential, yielding an impressive 53.8% enhancement. Minor increments in the friction factor, while present, prove negligible and can be safely overlooked.展开更多
This paper proposes a method to generate Bessel-like collimated beams with suppressed side lobes using the flexural vibration modes of a fixed boundary circular plate,which is excited by a longitudinally vibrating tra...This paper proposes a method to generate Bessel-like collimated beams with suppressed side lobes using the flexural vibration modes of a fixed boundary circular plate,which is excited by a longitudinally vibrating transducer in a ring excitation manner.The factors affecting the generation of Bessel-like collimated beams are investigated by theoretical analysis,numerical simulation and experimental methods.The results indicate that Bessel-like wave can be generated by a thin circular plate with fixed boundaries.The third-order mode of the circular plate can be modified to generate a collimated beam with suppressing side lobes when it is excited in a ring excitation manner and the excitation position lies between the first two nodal circles of the plate.As the excitation radius increases,the main lobe width of the resulting Bessel-like collimated beam decreases,the extent of the focusing region increases,and the amplitude of the side lobes initially increases and then decreases.Based on the simulation results,a prototype Bessel-like collimated beam generation system is made and measured experimentally.The experimental results are in good agreement with the numerical results.The Bessel-like collimated beam can be generated by the proposed system,which has potential application in the fields of long-range detection,imaging of highly attenuated materials,and airflow acceleration.展开更多
Ice accretion on structures such as aircraft wings and wind turbine blades poses serious risks to aerodynamic performance and operational safety,particularly in cold and humid environments.This study conducts numerica...Ice accretion on structures such as aircraft wings and wind turbine blades poses serious risks to aerodynamic performance and operational safety,particularly in cold and humid environments.This study conducts numerical simulations of ice formation on thin flat plates using CFD and FENSAP-ICE,exploring how air temperature,wind velocity,and angle of attack(AOA)affect icing behavior and aerodynamic characteristics.Results indicate that ice thickness increases linearly over time.Rime ice forms at low temperatures due to immediate droplet freezing,whereas glaze ice develops at higher temperatures when a water film forms and subsequently refreezes into protruding ice horns;under identical conditions,rime ice consistently produces thicker ice layers than glaze ice.Increasing wind speed substantially enhances ice growth and coverage,while speeds as low as 1 m/s result in minimal accretion.Changes in AOA shift the icing region toward the pressure side,and AOAs of equal magnitude but opposite sign yield symmetrical ice accretion patterns and identical maximum thickness values.After icing,the plate’s leading edge becomes smoother,slightly reducing drag while increasing lift and moment coefficients.These findings highlight the dominant roles of temperature,wind speed,and AOA in determining ice morphology,extent,and aerodynamic impact,providing valuable insights for predicting icing effects and developing mitigation strategies for structures operating in icing-prone regions.展开更多
Heat and mass transfer analysis of an incompressible, laminar boundary layer over solar flat plate collector evapora- tion systems for tannery effluent (soak liquor) is investigated. The governing equations are solved...Heat and mass transfer analysis of an incompressible, laminar boundary layer over solar flat plate collector evapora- tion systems for tannery effluent (soak liquor) is investigated. The governing equations are solved for various liquid to air velocity ratios. Profiles of velocity, temperature and concentration as well as their gradients are presented. The heat transfer and mass transfer coefficients thus obtained are used to evaluate mass of water evaporated for an inclined fibre-reinforced plastic (FRP) solar flat plate collector (FPC) with and without cover. Comparison of these results with the experimental performance shows encouraging trend of good agreement between them.展开更多
An experimental study on the traveling crossflow instability over a 60∘swept flat plate was conducted.The Mach number is 6,the angle of attack of the model is 5∘.The traveling crossflow waves and the secondary insta...An experimental study on the traveling crossflow instability over a 60∘swept flat plate was conducted.The Mach number is 6,the angle of attack of the model is 5∘.The traveling crossflow waves and the secondary instability of the traveling crossflow waves were visualized by nano-tracer-based planar laser scattering(NPLS)technique.In the spanwise NPLS images,the traveling crossflow waves appeared as regular strikes,and the secondary instability appeared as small eddies attached to strikes.The wavelet transform was used to study the wavelength contents of the traveling crossflow waves.The most amplified wavelength is stable before the secondary instability happening,which is around 12 mm at Re_(∞)=3.45×10^(6)m^(−1).Besides,the Reynolds number effects on the boundary layer transition and traveling crossflow instability were discussed.展开更多
This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined d...This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.展开更多
By using steady and transient methods, the total heat fluxes and the distributions of the heat flux were measured experimentally for an argon DC laminar plasma jet impinging normally on a flat plate at atmospheric pre...By using steady and transient methods, the total heat fluxes and the distributions of the heat flux were measured experimentally for an argon DC laminar plasma jet impinging normally on a flat plate at atmospheric pressure. Results show that the total heat fluxes measured with a steady method are a little bit higher than those with a transient method. Numerical simulation work was executed to compare with the experimental results.展开更多
This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum...This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum plate（180×120×3 nm^2）, which was covered by a transparent plate. The working fluid employed was ethanol. As the results, the influence parameters of thermal performance were investigated, such as filling ratio, heat load and operational orientations etc. Filling ratio was found to be a critical parameter, and its effect was rather complicated. According to its values the PHP plate could have four distinct working zones with different operational characteristics and heat transfer performance. The effect of heat load on thermal performance was found to be positive, and in general, iucrcasing the heat load would improve heat transfer performance. In order to analyze the effect of gravity on thermal performance, three different heat modes and total seven tilt angles were tested and compared. Successful operation at all orientations with respect to gravity was also achieved.展开更多
Many recent laboratory experiments and numerical simulations support a non-equilibrium dissipation scaling in decaying turbulence before it reaches an equilibrium state.By analyzing a direct numerical simulation(DNS)d...Many recent laboratory experiments and numerical simulations support a non-equilibrium dissipation scaling in decaying turbulence before it reaches an equilibrium state.By analyzing a direct numerical simulation(DNS)database of a transitional boundary-layer flow,we show that the transition region and the non-equilibrium turbulence region,which are located in different streamwise zones,present different non-equilibrium scalings.Moreover,in the wall-normal direction,the viscous sublayer,log layer,and outer layer show different non-equilibrium phenomena which differ from those in grid-generated turbulence and transitional channel flows.These findings are expected to shed light on the modelling of various types of non-equilibrium turbulent flows.展开更多
Numerical study on near wake flows of a flat plate in three kinds of oncoming flows is made by using the discrete vortex model and improved vorticity creation method. For steady oncoming flow, both gross and detailed ...Numerical study on near wake flows of a flat plate in three kinds of oncoming flows is made by using the discrete vortex model and improved vorticity creation method. For steady oncoming flow, both gross and detailed features of the wake flow are calculated and discussed. Then, in harmonic oscillatory oncoming flow two different wake flow patterns with K_c=2,4 and 10 are obtained respectively. Our results present a new wake flow pattern for low K_c numbers (K_c<5) describing vortex shedding, pairing and moving in a period of the oscillatory flow starting from rest. The calculated drag and inertia force coefficients are closer to experimental data from the U-tube than the previous results of vortex simulation. For in-line combined oncoming flow the vortex lock-in and dynamic characteristics are simulated. The results are shown to be in good agreement with experiments.展开更多
Transient operations are commonly founded in fluid machineries such as the starting, stopping, and variations of rotor speeds, etc. Flow generated from a started fiat plate is of fundamental importance. Experiments ha...Transient operations are commonly founded in fluid machineries such as the starting, stopping, and variations of rotor speeds, etc. Flow generated from a started fiat plate is of fundamental importance. Experiments have been done to observe the flow evolution in current researches. And in order to explore the flow in more detailed scale, some vortex methods with high resolution and other numerical methods were developed to solve various related problems by some researchers. But the promotion of vortex method to engineering application is rare due to its complexity and difficulty in specifying the boundary conditions. In order to build up a method of numerical study for such problems, a simplified model is built up with a flat plate. The development of two-dimensional viscous incompressible flow generated from an impulsively started and uniformly accelerated infinitesimally thin flat plate is simulated numerically. A dynamic mesh(DM) method based on the spring analogue and local remeshing is applied to realize the mesh motion caused by the started plate. Researches show that the mesh quality will decline under large grid shear force during the updating process. To conquer this problem, a region near the plate is separated to guarantee the mesh quality at location of interest which is the innovation of the present paper. All computations at least cover a period during which the plate translates 6 times its length. The simulated instantaneous velocity profiles, flow structures and drag coefficients under several Reynolds numbers (20 ≤ Re ≤ 126) and accelerations (20 m/s2≤ a ≤ 152 m/s2) are presented and compared with existing results in literatures. Comparisons are found to be satisfactory, confirming the validity of the current proposed method(region separated DM). The proposed DM method is firstly used to study the transient flow generated from a started flat plate and can be used in further study of transient characteristics during transient operations of turbo machineries.展开更多
The pulsatile electroosmotic flow （PEOF） of a Maxwell fluid in a parallel flat plate microchannel with asymmetric wall zeta potentials is theoretically analyzed. By combining the linear Maxwell viscoelastic model, t...The pulsatile electroosmotic flow （PEOF） of a Maxwell fluid in a parallel flat plate microchannel with asymmetric wall zeta potentials is theoretically analyzed. By combining the linear Maxwell viscoelastic model, the Cauchy equation, and the electric field solution obtained from the linearized PoissomBoltzmann equation, a hyperbolic par- tial differential equation is obtained to derive the flow field. The PEOF is controlled by the angular Reynolds number, the ratio of the zeta potentials of the microchannel walls, the electrokinetic parameter, and the elasticity number. The main results obtained from this analysis show strong oscillations in the velocity profiles when the values of the elas- ticity number and the angular Reynolds number increase due to the competition among the elastic, viscous, inertial, and electric forces in the flow.展开更多
In the present work, computational simulations was made using ANSYS CFX to predict the improvements in film cooling performance with dual trench. Dual-trench confguradon consists of two trenches together, one wider tr...In the present work, computational simulations was made using ANSYS CFX to predict the improvements in film cooling performance with dual trench. Dual-trench confguradon consists of two trenches together, one wider trench and the other is narrow trench that extruded from the wider one. Several blowing ratios in the range （0.5：5） were investigated. The pitch-to-diameter ratio of 2.775 is used. By using the dual trench configuration, the coolant jet impacted the trench wall two times allowing increasing the spreading of coolant laterally in the trench, reducing jet velocity and jet completely covered on the surface. The results indicate that this configuration increased adiabatic effectiveness as blowing ratio increased. The spatially averaged adiabatic effectiveness reached 57.6% for at M= 2. No observed film blow-off at all blowing ratios. The adiabatic film effectiveness of dual trench case outperformed the narrow trench case, laidback fan-shaped hole, fan-shaped hole and cylinder hole at different blowing ratios.展开更多
In this paper,we studied theoretically and numerically heated losses of a flat solar collector to model the solar water heating system for the Kazakhstan climate condition.For different climatic zones with a growing c...In this paper,we studied theoretically and numerically heated losses of a flat solar collector to model the solar water heating system for the Kazakhstan climate condition.For different climatic zones with a growing cost for energy or lack of central heating systems,promising is to find ways to improve the energy efficiency of the solar system.The mathematical model(based on ordinary differential equation)simulated the solar system work process under different conditions.To bridge the modeling and real values results,we studied the important physical parameters such as loss coefficient,Nu,Ra,and Pr values.They impacted the efficiency of flat solar collectors and heat losses of the system.The developed mathematical models,the design and composition of the software and hardware complex,and automated control and monitoring systems allow solar hot water heating systems to increase the energy efficiency of life support systems and heat supply of buildings by reducing energy consumption for heat supply.The simulation result showed that during the daytime,the temperature of water in the collector is 70°C;the storage of heated water since heated water is cooled at night.We defined that a work period of the system can be extended with high efficiency(April-October)for Almaty region.展开更多
Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), a...Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), and aluminum(Al2O3) nanoparticles in pure water on the performance of a flat plate solar collector(FPSC) and a numerical model was proposed. The influence of the nanofluid type on the thermal efficiency was critically investigated and discussed. The eff ect of the mass flow rate on the performance was also analyzed and discussed. Based on correlations of the thermophysical properties of nanofluids, a sensitivity analysis was used to analyze the impact of the nanoparticles on the base fluid. The results indicate that the performance of the FPSC with Cu/water nanofluid was better than that of FPSCs using CuO/water or Al2O3/water nanofluids. When the mass flow rate of the nanofluids was 8.0 L/min, the efficiency of the FPSC was much greater than those at the flow rates of 5.0 L/min and 2.0 L/min. Mean enhancements in thermal efficiency of 4.44%, 4.27%, and 4.21% were observed when 2.0 L/min was applied using Cu/water, Cu O/water, and Al2O3/water nanofluids, respectively. Improvements in thermal efficiency of 2.76%, 2.53%, and 2.47% occurred when 8.0 L/min was applied.展开更多
PHEs （plate heat exchangers） are among the most common thermal equipments in diverse industries particularly in oil and gas companies. This wide usage is obviously due to significant benefits of these heat exchanger...PHEs （plate heat exchangers） are among the most common thermal equipments in diverse industries particularly in oil and gas companies. This wide usage is obviously due to significant benefits of these heat exchangers over other types. In this article, a behavioral analysis of heat transfer in fiat plates of these heat exchangers in laminar flow situation through CFD （computational fluid dynamics） simulation using FLUENT 6.3.26 software is done. The study reveals results graphically based on fluid＇s behavior in co-current and counter current flows and discusses thermal indexes consisting of heat transfer coefficient, Nusslet and total heat flux in both conditions. Eventually, a comparison via the graphical results is presented between the two types of flow directions.展开更多
To research solar energy's efficiency and environmental benefits,the thermal efficiency,exergy,and entropy of solar collectors were calculated.The experiment involved two glass-topped collectors,fluid transfer tub...To research solar energy's efficiency and environmental benefits,the thermal efficiency,exergy,and entropy of solar collectors were calculated.The experiment involved two glass-topped collectors,fluid transfer tubes,and aluminum heat-absorbing plates.Glass wool insulation minimized heat loss.A 0.5% TiO_(2)/Water nanofluid was created using a mechanical and ultrasonic stirrer.Results showed that solar radiation increased thermal efficiency until midday,reaching 48.48% for water and 51.23% for the nanofluid.With increasing mass flow rates from 0.0045 kg/s to 0.02 kg/s,thermal efficiency improved from 16.26% to 47.37% for water and from 20.65% to 48.76% for the nanofluid.Filtered water provided 380 W and 395 W of energy in March and April,while the nanofluid increased it to 395 W and 415 W during these months.Mass flow generated energy,and the Reynolds number raised entropy.The noon exergy efficiency for nanofluids was 50%-55%,compared to 30% for water.At noon,the broken exergy measured 877.53 W for the nanofluid and 880.12 W for water.In Kirkuk,Iraq,the 0.5% TiO_(2)/Water nanofluid outperformed water in solar collectors.展开更多
Current trends on CFD （Computational Fluid Dynamics） along with high performance computing are moving towards using modem GPUs （Graphics Processing Units） in order to achieve substantial execution speedup. Consequ...Current trends on CFD （Computational Fluid Dynamics） along with high performance computing are moving towards using modem GPUs （Graphics Processing Units） in order to achieve substantial execution speedup. Consequently, it is definitely crucial to have some understanding about execution time of different computational methods and parallelization procedures. In this study, two GPU accelerated schemes namely LBM （Lattice Boltzmann Method） and SFV （Stream Function-Vorticity） formulation are investigated and compared for simulation of flow over a fiat plate. The comparisons are based on solvers runtime and speedup and GPU type of structuring. On study the authors found that although the runtime for SFV formulation is less than LBM, LBM has greater potential to obtain higher speedup by using modern GPUs like NVIDIA GTX 480. In addition, a performance sensitivity is done to investigate for different GPU type of structures as a considerable parameter. The difference between GPU runtime in optimum and regular conditions indicates that using one-dimensional structuring can improve the GPU performance about 50 percent.展开更多
At turbomachinery relevant flow conditions the boundary layers are often transitional with laminar-to-turbulent transition occurring. The characteristics of the main flow can depend highly on the state of the boundary...At turbomachinery relevant flow conditions the boundary layers are often transitional with laminar-to-turbulent transition occurring. The characteristics of the main flow can depend highly on the state of the boundary layer. Therefore it can be vitally important for the designer to understand the process of laminar-to-turbulent transition and to determine the position and length of the transitional region. In this paper the flow over a flat plate is experimentally studied in order to investigate and better understand transitional flow. Preston tube measurements as well as a thermographic camera system were performed for two different inlet velocities in order to determine the position of the transitional zone. The results of the experiment are compared to numerical flow solutions using a common transition model to determine its capability. The simulation has been performed with the two commercial codes CFX and Fluent by Ansys and an in-house code called LINARS. As a result of this study, a better understanding of the experimental and numerical methods for determining transition shall be given.展开更多
The influence of sand dust on discharge of external insulation has caused widespread concern.At present,the research results show wind-sand electricity has a remarkable effect on the discharge characteristics of insul...The influence of sand dust on discharge of external insulation has caused widespread concern.At present,the research results show wind-sand electricity has a remarkable effect on the discharge characteristics of insulator and has little influence on the discharge characteristics of air gap.The flashover of insulator strings occurs along the insulator surface and air gaps,and the sand dust deposited on the insulator surface may affect the flashover characteristics of insulator strings.This paper studies the flashover characteristics of flat plate model under DC voltage in wind-sand condition.The experimental results show that under positive polarity voltage,the flashover voltage of the flat plate model has a maximum value,while under negative polarity voltage,the flashover voltage of the flat plate model has a minimum value with a certain degree of sand dust deposition.The wind or sand in sand-dust weather has an important effect on the flashover characteristics of the flat plate model.In certain variation range of electric charge,electric charge of sand dust has little effect on the flashover voltage of flat plate model under DC voltage.The deposition of sand has significant influence on the flashover process of flat plate model,which is related to the deposition density and moisture content of sand particle.展开更多
文摘This study delves into both experimental and analytical examinations of heat exchange in a straight channel, where Al_(2)O_(3)-water nanofluids are utilized, spanning the Reynolds number spectrum from 100 to 1800. Diverse volume fractions(1%, 2%, and 3%) of Al_(2)O_(3)-water nanofluids are meticulously prepared and analyzed. The essential physical properties of these nanofluids, critical for evaluating their thermal and flow characteristics, have been comprehensively assessed. From a quantitative perspective, numerical simulations are employed to predict the Nusselt number(Nu) and friction factor(f). The empirical findings reveal intriguing trends: the friction factor experiences an upward trend with diminishing velocity, attributed to heightened molecular cohesion. Conversely, the friction factor demonstrates a decline with diminishing volume fractions, a consequence of reduced particle size. Both the nanofluid's viscosity and heat transfer coefficient exhibit a rise in tandem with augmented volume flow rate and concentration gradient. Notably, the simulation results harmonize remarkably well with experimental data. Rigorous validation against prior studies underscores the robust consistency of these outcomes. In the pursuit of augmenting heat transfer, a volume fraction of 3% emerges as particularly influential, yielding an impressive 53.8% enhancement. Minor increments in the friction factor, while present, prove negligible and can be safely overlooked.
基金Project supported by the National Natural Science Foundation of China(Grant No.12474440).
文摘This paper proposes a method to generate Bessel-like collimated beams with suppressed side lobes using the flexural vibration modes of a fixed boundary circular plate,which is excited by a longitudinally vibrating transducer in a ring excitation manner.The factors affecting the generation of Bessel-like collimated beams are investigated by theoretical analysis,numerical simulation and experimental methods.The results indicate that Bessel-like wave can be generated by a thin circular plate with fixed boundaries.The third-order mode of the circular plate can be modified to generate a collimated beam with suppressing side lobes when it is excited in a ring excitation manner and the excitation position lies between the first two nodal circles of the plate.As the excitation radius increases,the main lobe width of the resulting Bessel-like collimated beam decreases,the extent of the focusing region increases,and the amplitude of the side lobes initially increases and then decreases.Based on the simulation results,a prototype Bessel-like collimated beam generation system is made and measured experimentally.The experimental results are in good agreement with the numerical results.The Bessel-like collimated beam can be generated by the proposed system,which has potential application in the fields of long-range detection,imaging of highly attenuated materials,and airflow acceleration.
基金supported by the National Natural Science Foundation of China(52278532)Sichuan Science and Technology Program(2024NSFSC0153)。
文摘Ice accretion on structures such as aircraft wings and wind turbine blades poses serious risks to aerodynamic performance and operational safety,particularly in cold and humid environments.This study conducts numerical simulations of ice formation on thin flat plates using CFD and FENSAP-ICE,exploring how air temperature,wind velocity,and angle of attack(AOA)affect icing behavior and aerodynamic characteristics.Results indicate that ice thickness increases linearly over time.Rime ice forms at low temperatures due to immediate droplet freezing,whereas glaze ice develops at higher temperatures when a water film forms and subsequently refreezes into protruding ice horns;under identical conditions,rime ice consistently produces thicker ice layers than glaze ice.Increasing wind speed substantially enhances ice growth and coverage,while speeds as low as 1 m/s result in minimal accretion.Changes in AOA shift the icing region toward the pressure side,and AOAs of equal magnitude but opposite sign yield symmetrical ice accretion patterns and identical maximum thickness values.After icing,the plate’s leading edge becomes smoother,slightly reducing drag while increasing lift and moment coefficients.These findings highlight the dominant roles of temperature,wind speed,and AOA in determining ice morphology,extent,and aerodynamic impact,providing valuable insights for predicting icing effects and developing mitigation strategies for structures operating in icing-prone regions.
文摘Heat and mass transfer analysis of an incompressible, laminar boundary layer over solar flat plate collector evapora- tion systems for tannery effluent (soak liquor) is investigated. The governing equations are solved for various liquid to air velocity ratios. Profiles of velocity, temperature and concentration as well as their gradients are presented. The heat transfer and mass transfer coefficients thus obtained are used to evaluate mass of water evaporated for an inclined fibre-reinforced plastic (FRP) solar flat plate collector (FPC) with and without cover. Comparison of these results with the experimental performance shows encouraging trend of good agreement between them.
基金This work was supported by the National Key Research and Development Plan of China(Grant 2019YFA0405300)the National Natural Science Foundation of China(Grants 11832018,12002375,11527802)the Project of National University of Defense Technology(ZK20-12).
文摘An experimental study on the traveling crossflow instability over a 60∘swept flat plate was conducted.The Mach number is 6,the angle of attack of the model is 5∘.The traveling crossflow waves and the secondary instability of the traveling crossflow waves were visualized by nano-tracer-based planar laser scattering(NPLS)technique.In the spanwise NPLS images,the traveling crossflow waves appeared as regular strikes,and the secondary instability appeared as small eddies attached to strikes.The wavelet transform was used to study the wavelength contents of the traveling crossflow waves.The most amplified wavelength is stable before the secondary instability happening,which is around 12 mm at Re_(∞)=3.45×10^(6)m^(−1).Besides,the Reynolds number effects on the boundary layer transition and traveling crossflow instability were discussed.
基金the Ger man National Science Foundation (GR-412/33-2)Shanghai Leading Academic Discipline Project (No.B604)
文摘This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.
基金he National Natural Science Foundation of China under the grant No. 59836220 and 19975064and endowed with President's Foundati
文摘By using steady and transient methods, the total heat fluxes and the distributions of the heat flux were measured experimentally for an argon DC laminar plasma jet impinging normally on a flat plate at atmospheric pressure. Results show that the total heat fluxes measured with a steady method are a little bit higher than those with a transient method. Numerical simulation work was executed to compare with the experimental results.
基金Supported by the Ger man National Science Foundation (DFG)(No. GR412/33)
文摘This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum plate（180×120×3 nm^2）, which was covered by a transparent plate. The working fluid employed was ethanol. As the results, the influence parameters of thermal performance were investigated, such as filling ratio, heat load and operational orientations etc. Filling ratio was found to be a critical parameter, and its effect was rather complicated. According to its values the PHP plate could have four distinct working zones with different operational characteristics and heat transfer performance. The effect of heat load on thermal performance was found to be positive, and in general, iucrcasing the heat load would improve heat transfer performance. In order to analyze the effect of gravity on thermal performance, three different heat modes and total seven tilt angles were tested and compared. Successful operation at all orientations with respect to gravity was also achieved.
基金Project supported by the National Natural Science Foundation of China(Nos.12002318,11572025,11772032,and 51420105008)the Science Foundation of North University of China(No.XJJ201929)。
文摘Many recent laboratory experiments and numerical simulations support a non-equilibrium dissipation scaling in decaying turbulence before it reaches an equilibrium state.By analyzing a direct numerical simulation(DNS)database of a transitional boundary-layer flow,we show that the transition region and the non-equilibrium turbulence region,which are located in different streamwise zones,present different non-equilibrium scalings.Moreover,in the wall-normal direction,the viscous sublayer,log layer,and outer layer show different non-equilibrium phenomena which differ from those in grid-generated turbulence and transitional channel flows.These findings are expected to shed light on the modelling of various types of non-equilibrium turbulent flows.
基金The project supported by National Natural Science Fundation of China and LNM of Institute of Mechanics. CAS .
文摘Numerical study on near wake flows of a flat plate in three kinds of oncoming flows is made by using the discrete vortex model and improved vorticity creation method. For steady oncoming flow, both gross and detailed features of the wake flow are calculated and discussed. Then, in harmonic oscillatory oncoming flow two different wake flow patterns with K_c=2,4 and 10 are obtained respectively. Our results present a new wake flow pattern for low K_c numbers (K_c<5) describing vortex shedding, pairing and moving in a period of the oscillatory flow starting from rest. The calculated drag and inertia force coefficients are closer to experimental data from the U-tube than the previous results of vortex simulation. For in-line combined oncoming flow the vortex lock-in and dynamic characteristics are simulated. The results are shown to be in good agreement with experiments.
基金supported by National Natural Science Foundation of China(Grant Nos.50979095,51176168,50906074)China Postdoctoral Science Foundation(Grant Nos.20100471697,201104713)
文摘Transient operations are commonly founded in fluid machineries such as the starting, stopping, and variations of rotor speeds, etc. Flow generated from a started fiat plate is of fundamental importance. Experiments have been done to observe the flow evolution in current researches. And in order to explore the flow in more detailed scale, some vortex methods with high resolution and other numerical methods were developed to solve various related problems by some researchers. But the promotion of vortex method to engineering application is rare due to its complexity and difficulty in specifying the boundary conditions. In order to build up a method of numerical study for such problems, a simplified model is built up with a flat plate. The development of two-dimensional viscous incompressible flow generated from an impulsively started and uniformly accelerated infinitesimally thin flat plate is simulated numerically. A dynamic mesh(DM) method based on the spring analogue and local remeshing is applied to realize the mesh motion caused by the started plate. Researches show that the mesh quality will decline under large grid shear force during the updating process. To conquer this problem, a region near the plate is separated to guarantee the mesh quality at location of interest which is the innovation of the present paper. All computations at least cover a period during which the plate translates 6 times its length. The simulated instantaneous velocity profiles, flow structures and drag coefficients under several Reynolds numbers (20 ≤ Re ≤ 126) and accelerations (20 m/s2≤ a ≤ 152 m/s2) are presented and compared with existing results in literatures. Comparisons are found to be satisfactory, confirming the validity of the current proposed method(region separated DM). The proposed DM method is firstly used to study the transient flow generated from a started flat plate and can be used in further study of transient characteristics during transient operations of turbo machineries.
基金Project supported by the Fondo Sectorial de Investigación para la Educación from the Secretar a de Educación Pública-Consejo Nacional de Ciencia y Tecnología(No.CB-2013/220900)the Secretaría de Investigación y Posgrado from Instituto Politécnico Nacional of Mexico(No.20171181)
文摘The pulsatile electroosmotic flow （PEOF） of a Maxwell fluid in a parallel flat plate microchannel with asymmetric wall zeta potentials is theoretically analyzed. By combining the linear Maxwell viscoelastic model, the Cauchy equation, and the electric field solution obtained from the linearized PoissomBoltzmann equation, a hyperbolic par- tial differential equation is obtained to derive the flow field. The PEOF is controlled by the angular Reynolds number, the ratio of the zeta potentials of the microchannel walls, the electrokinetic parameter, and the elasticity number. The main results obtained from this analysis show strong oscillations in the velocity profiles when the values of the elas- ticity number and the angular Reynolds number increase due to the competition among the elastic, viscous, inertial, and electric forces in the flow.
基金Supprted by Harbin Engineering University Scholarship under Grant No. 20100903D01
文摘In the present work, computational simulations was made using ANSYS CFX to predict the improvements in film cooling performance with dual trench. Dual-trench confguradon consists of two trenches together, one wider trench and the other is narrow trench that extruded from the wider one. Several blowing ratios in the range （0.5：5） were investigated. The pitch-to-diameter ratio of 2.775 is used. By using the dual trench configuration, the coolant jet impacted the trench wall two times allowing increasing the spreading of coolant laterally in the trench, reducing jet velocity and jet completely covered on the surface. The results indicate that this configuration increased adiabatic effectiveness as blowing ratio increased. The spatially averaged adiabatic effectiveness reached 57.6% for at M= 2. No observed film blow-off at all blowing ratios. The adiabatic film effectiveness of dual trench case outperformed the narrow trench case, laidback fan-shaped hole, fan-shaped hole and cylinder hole at different blowing ratios.
基金Thisworkwas supported by the Ministry of Education and Science of theRepublic of Kazakhstan BR10965172。
文摘In this paper,we studied theoretically and numerically heated losses of a flat solar collector to model the solar water heating system for the Kazakhstan climate condition.For different climatic zones with a growing cost for energy or lack of central heating systems,promising is to find ways to improve the energy efficiency of the solar system.The mathematical model(based on ordinary differential equation)simulated the solar system work process under different conditions.To bridge the modeling and real values results,we studied the important physical parameters such as loss coefficient,Nu,Ra,and Pr values.They impacted the efficiency of flat solar collectors and heat losses of the system.The developed mathematical models,the design and composition of the software and hardware complex,and automated control and monitoring systems allow solar hot water heating systems to increase the energy efficiency of life support systems and heat supply of buildings by reducing energy consumption for heat supply.The simulation result showed that during the daytime,the temperature of water in the collector is 70°C;the storage of heated water since heated water is cooled at night.We defined that a work period of the system can be extended with high efficiency(April-October)for Almaty region.
文摘Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), and aluminum(Al2O3) nanoparticles in pure water on the performance of a flat plate solar collector(FPSC) and a numerical model was proposed. The influence of the nanofluid type on the thermal efficiency was critically investigated and discussed. The eff ect of the mass flow rate on the performance was also analyzed and discussed. Based on correlations of the thermophysical properties of nanofluids, a sensitivity analysis was used to analyze the impact of the nanoparticles on the base fluid. The results indicate that the performance of the FPSC with Cu/water nanofluid was better than that of FPSCs using CuO/water or Al2O3/water nanofluids. When the mass flow rate of the nanofluids was 8.0 L/min, the efficiency of the FPSC was much greater than those at the flow rates of 5.0 L/min and 2.0 L/min. Mean enhancements in thermal efficiency of 4.44%, 4.27%, and 4.21% were observed when 2.0 L/min was applied using Cu/water, Cu O/water, and Al2O3/water nanofluids, respectively. Improvements in thermal efficiency of 2.76%, 2.53%, and 2.47% occurred when 8.0 L/min was applied.
文摘PHEs （plate heat exchangers） are among the most common thermal equipments in diverse industries particularly in oil and gas companies. This wide usage is obviously due to significant benefits of these heat exchangers over other types. In this article, a behavioral analysis of heat transfer in fiat plates of these heat exchangers in laminar flow situation through CFD （computational fluid dynamics） simulation using FLUENT 6.3.26 software is done. The study reveals results graphically based on fluid＇s behavior in co-current and counter current flows and discusses thermal indexes consisting of heat transfer coefficient, Nusslet and total heat flux in both conditions. Eventually, a comparison via the graphical results is presented between the two types of flow directions.
文摘To research solar energy's efficiency and environmental benefits,the thermal efficiency,exergy,and entropy of solar collectors were calculated.The experiment involved two glass-topped collectors,fluid transfer tubes,and aluminum heat-absorbing plates.Glass wool insulation minimized heat loss.A 0.5% TiO_(2)/Water nanofluid was created using a mechanical and ultrasonic stirrer.Results showed that solar radiation increased thermal efficiency until midday,reaching 48.48% for water and 51.23% for the nanofluid.With increasing mass flow rates from 0.0045 kg/s to 0.02 kg/s,thermal efficiency improved from 16.26% to 47.37% for water and from 20.65% to 48.76% for the nanofluid.Filtered water provided 380 W and 395 W of energy in March and April,while the nanofluid increased it to 395 W and 415 W during these months.Mass flow generated energy,and the Reynolds number raised entropy.The noon exergy efficiency for nanofluids was 50%-55%,compared to 30% for water.At noon,the broken exergy measured 877.53 W for the nanofluid and 880.12 W for water.In Kirkuk,Iraq,the 0.5% TiO_(2)/Water nanofluid outperformed water in solar collectors.
文摘Current trends on CFD （Computational Fluid Dynamics） along with high performance computing are moving towards using modem GPUs （Graphics Processing Units） in order to achieve substantial execution speedup. Consequently, it is definitely crucial to have some understanding about execution time of different computational methods and parallelization procedures. In this study, two GPU accelerated schemes namely LBM （Lattice Boltzmann Method） and SFV （Stream Function-Vorticity） formulation are investigated and compared for simulation of flow over a fiat plate. The comparisons are based on solvers runtime and speedup and GPU type of structuring. On study the authors found that although the runtime for SFV formulation is less than LBM, LBM has greater potential to obtain higher speedup by using modern GPUs like NVIDIA GTX 480. In addition, a performance sensitivity is done to investigate for different GPU type of structures as a considerable parameter. The difference between GPU runtime in optimum and regular conditions indicates that using one-dimensional structuring can improve the GPU performance about 50 percent.
文摘At turbomachinery relevant flow conditions the boundary layers are often transitional with laminar-to-turbulent transition occurring. The characteristics of the main flow can depend highly on the state of the boundary layer. Therefore it can be vitally important for the designer to understand the process of laminar-to-turbulent transition and to determine the position and length of the transitional region. In this paper the flow over a flat plate is experimentally studied in order to investigate and better understand transitional flow. Preston tube measurements as well as a thermographic camera system were performed for two different inlet velocities in order to determine the position of the transitional zone. The results of the experiment are compared to numerical flow solutions using a common transition model to determine its capability. The simulation has been performed with the two commercial codes CFX and Fluent by Ansys and an in-house code called LINARS. As a result of this study, a better understanding of the experimental and numerical methods for determining transition shall be given.
基金Project Supported by National Natural Science Foundation of China（90510014 ）.
文摘The influence of sand dust on discharge of external insulation has caused widespread concern.At present,the research results show wind-sand electricity has a remarkable effect on the discharge characteristics of insulator and has little influence on the discharge characteristics of air gap.The flashover of insulator strings occurs along the insulator surface and air gaps,and the sand dust deposited on the insulator surface may affect the flashover characteristics of insulator strings.This paper studies the flashover characteristics of flat plate model under DC voltage in wind-sand condition.The experimental results show that under positive polarity voltage,the flashover voltage of the flat plate model has a maximum value,while under negative polarity voltage,the flashover voltage of the flat plate model has a minimum value with a certain degree of sand dust deposition.The wind or sand in sand-dust weather has an important effect on the flashover characteristics of the flat plate model.In certain variation range of electric charge,electric charge of sand dust has little effect on the flashover voltage of flat plate model under DC voltage.The deposition of sand has significant influence on the flashover process of flat plate model,which is related to the deposition density and moisture content of sand particle.
