Design a precision electroplating mechanical structure for automobiles based on finite element analysis method and analyze its mechanical properties.Taking the automobile steering knuckle as the research object,ABAQUS...Design a precision electroplating mechanical structure for automobiles based on finite element analysis method and analyze its mechanical properties.Taking the automobile steering knuckle as the research object,ABAQUS parametric modeling technology is used to construct its three-dimensional geometric model,and geometric simplification is carried out.Two surface treatment processes,HK-35 zinc nickel alloy electroplating and pure zinc electroplating,were designed,and the influence of different coatings on the mechanical properties of steering knuckles was compared and analyzed through numerical simulation.At the same time,standard specimens were prepared for salt spray corrosion testing and scratch method combined strength testing to verify the numerical simulation results.The results showed that under emergency braking and composite working conditions,the peak Von Mises stress of the zinc nickel alloy coating was 119.85 MPa,which was lower than that of the pure zinc coating and the alkaline electroplated zinc layer.Its equivalent strain value was 652×10^(-6),which was lower than that of the pure zinc coating and the alkaline electroplated zinc layer.Experimental data confirms that zinc nickel alloy coatings exhibit significant advantages in stress distribution uniformity,strain performance,and load-bearing capacity in high stress zones.The salt spray corrosion test further indicates that the coating has superior corrosion resistance and coating substrate interface bonding strength,which can significantly improve the mechanical stability and long-term reliability of automotive precision electroplating mechanical structures.展开更多
Objective: To compare the stress distribution in the periodontal ligament under different orthodontic forces during canine distalization using long-arm brackets, and to determine the optimal force value for this devic...Objective: To compare the stress distribution in the periodontal ligament under different orthodontic forces during canine distalization using long-arm brackets, and to determine the optimal force value for this device in orthodontic treatment. Methods: A finite element model was constructed after extracting the mandibular first premolar, and a long-arm bracket with a traction height of 6 mm was placed on the labial side of the mandibular canine. Three working conditions of 50 g, 100 g, and 150 g were simulated, and the magnitude and distribution of von Mises stress in the periodontal ligament were compared for each condition. Results: The maximum von Mises stress in the periodontal ligament was 0.013281 MPa in the 50 g condition, 0.02536 MPa in the 100 g condition, and 0.035549 MPa in the 150 g condition. As the orthodontic force increased, the stress distribution area in the periodontal ligament also expanded. Conclusion: A 100 g orthodontic force is the most suitable when using long-arm brackets, providing a relatively uniform stress distribution in the periodontal ligament and keeping the stress within a reasonable range.展开更多
Due to their superior properties, the interest in nanostructures is increasing today in engineering. This study presents a new two-noded curved finite element for analyzing the in-plane static behaviors of curved nano...Due to their superior properties, the interest in nanostructures is increasing today in engineering. This study presents a new two-noded curved finite element for analyzing the in-plane static behaviors of curved nanobeams. Opposite to traditional curved finite elements developed by using approximate interpolation functions, the proposed curved finite element is developed by using exact analytical solutions. Although this approach was first introduced for analyzing the mechanical behaviors of macro-scale curved beams by adopting the local theory of elasticity, the exact analytical expressions used in this study were obtained from the solutions of governing equations that were expressed via the differential form of the nonlocal theory of elasticity. Therefore, the effects of shear strain and axial extension included in the analytical formulation are also inherited by the curved finite element developed here. The rigidity matrix and the consistent force vector are developed for a circular finite element. To demonstrate the applicability of the method, static analyses of various curved nanobeams subjected to different boundary conditions and loading scenarios are performed, and the obtained results are compared with the exact analytical ones. The presented study provides an accurate and low computational cost method for researchers to investigate the in-plane static behavior of curved nanobeams.展开更多
To effectively address the challenge where the speed of tunnel lining construction struggles to match that of tunnel face and inverted arch construction,and to enhance the quality of secondary lining,a new type of ske...To effectively address the challenge where the speed of tunnel lining construction struggles to match that of tunnel face and inverted arch construction,and to enhance the quality of secondary lining,a new type of skeleton-free,traversing secondary lining trolley has been developed.This trolley features a set of gantries paired with two sets of formwork.The formwork adopts a multi-segment hinged and strengthened design,ensuring its own strength can meet the requirements of secondary lining concrete pouring without relying on the support of the gantries.When retracted,the formwork can be transported by the gantries through another set of formwork in the supporting state,enabling early formwork support,effectively accelerating the construction progress of the tunnel’s secondary lining,and extending the maintenance time of the secondary lining with the formwork.Finite element software modeling was used for simulation calculations,and the results indicate that the structural strength,stiffness,and other performance parameters of the new secondary lining trolley meet the design requirements,verifying the rationality of the design.展开更多
Identifying the damage and fracture properties of nuclear graphite materials and accurately simulating them are crucial when designing graphite core structures.To simulate the damage evolution and crack propagation of...Identifying the damage and fracture properties of nuclear graphite materials and accurately simulating them are crucial when designing graphite core structures.To simulate the damage evolution and crack propagation of graphite under stress in a finite element model,compression tests on disks and three-point bending tests on center-notched beams for fine-grained graphite(CDI-1D and IG11 graphite)were conducted.During these tests,digital image correlation and electronic speckle pattern interferometry techniques were utilized to observe the surface full-field displacements of the specimens.A segmented finite element inverse analysis method was developed to characterize the graphite’s damage evolution by quantifying the reduction in Young’s modulus with tensile and compressive strains in disk specimens.The fracture energy and bilinear tensile softening curve of the graphite were determined by comparing the load–displacement responses of the three-point bending tests and the finite element simulation.Finally,by combining the identified damage laws with a fracture criterion based on fracture energy,a damage–fracture model was established and used to simulate tensile tests on L-shaped specimens with different fillet radii.Simulations indicate that the damage area at the fillet expands with increasing radius,creating a blunting effect that enhances the load-bearing capacity of the specimens.This damage–fracture model can be applied to simulate graphite components in core structures.展开更多
Purpose–The brake pipe system was an essential braking component of the railway freight trains,but the existing E-type sealing rings had problems such as insufficient low-temperature resistance,poor heat stability an...Purpose–The brake pipe system was an essential braking component of the railway freight trains,but the existing E-type sealing rings had problems such as insufficient low-temperature resistance,poor heat stability and short service life.To address these issues,low-phenyl silicone rubber was prepared and tested,and the finite element analysis and experimental studies on the sealing performance of its sealing rings were carried out.Design/methodology/approach–The low-temperature resistance and thermal stability of the prepared lowphenyl silicone rubber were studied using low-temperature tensile testing,differential scanning calorimetry,dynamic thermomechanical analysis and thermogravimetric analysis.The sealing performance of the lowphenyl silicone rubber sealing ring was studied by using finite element analysis software abaqus and experiments.Findings–The prepared low-phenyl silicone rubber sealing ring possessed excellent low-temperature resistance and thermal stability.According to the finite element analysis results,the finish of the flange sealing surface and groove outer edge should be ensured,and extrusion damage should be avoided.The sealing rings were more susceptible to damage in high compression ratio and/or low-temperature environments.When the sealing effect was ensured,a small compression ratio should be selected,and rubbers with hardness and elasticity less affected by temperature should be selected.The prepared low-phenyl silicone rubber sealing ring had zero leakage at both room temperature(RT)and�508C.Originality/value–The innovation of this study is that it provides valuable data and experience for the future development of the sealing rings used in the brake pipe flange joints of the railway freight cars in China.展开更多
Total hip arthroplasty for adults with sequelae from childhood hip disorders poses significant challenges due to altered anatomy.The paper published by Oommen et al reviews the essential management strategies for thes...Total hip arthroplasty for adults with sequelae from childhood hip disorders poses significant challenges due to altered anatomy.The paper published by Oommen et al reviews the essential management strategies for these complex cases.This article explores the integration of finite element analysis(FEA)to enhance surgical precision and outcomes.FEA provides detailed biomechanical insights,aiding in preoperative planning,implant design,and surgical technique optimization.By simulating implant configurations and assessing bone quality,FEA helps in customizing implants and evaluating surgical techniques like subtrochanteric shortening osteotomy.Advanced imaging techniques,such as 3D printing,virtual reality,and augmented reality,further enhance total hip arthroplasty precision.Future research should focus on validating FEA models,developing patient-specific simulations,and promoting multidisciplinary collaboration.Integrating FEA and advanced technologies in total hip arthroplasty can improve functional outcomes,reduce complications,and enhance quality of life for patients with childhood hip disorder sequelae.展开更多
The increasing occurrence of sinkholes caused by water main bursts has attracted significant research attention in recent years.This study addresses the gap in evaluating soil blowout stability resulting from water ma...The increasing occurrence of sinkholes caused by water main bursts has attracted significant research attention in recent years.This study addresses the gap in evaluating soil blowout stability resulting from water main failures by investigating the three-dimensional stability of blowouts with circular,hemispherical,and spherical openings.Advanced finite element limit analysis(FELA)combined with adaptive meshing is employed to analyze critical factors,including soil cover depth,surcharge pressure,and internal water pressure,that contribute to blowout failure.In addition,dimensionless ratios are used throughout the paper to assess the influence of these factors.Numerical findings are rigorously validated,ensuring reliability and accuracy.Practical design charts are provided to accommodate a wide range of design scenarios,offering valuable guidance for engineers.This study introduces a pioneering sinkhole simulation methodology,leading to the understanding of three-dimensional blowout stability mechanisms.展开更多
Purpose–This paper aims to offer a novel viewpoint for improving performance and reliability by developing and optimizing suspension components in a Y25 bogie through material optimization based on wheel–rail intera...Purpose–This paper aims to offer a novel viewpoint for improving performance and reliability by developing and optimizing suspension components in a Y25 bogie through material optimization based on wheel–rail interactions under variable load and track conditions.Design/methodology/approach–The suspension system,a critical component ensuring adaptation to road and load conditions in all vehicle types,is especially vital in heavy freight and passenger trains.In this context,the suspension set of the Y25 bogie–commonly used in T€urkiye and Europe–was modelled using CATIAV5,and stress analyses have been performed by way of ANSYS using the finite element analysis(FEA)method.E300-520-M cast steel was selected for the bogie frame,while two different spring steels,61SiCr7 and 51CrV4,were considered for the suspension springs.The modeled system was subjected to numerical analysis under loading conditions.The resulting stresses and displacements were compared with the mechanical properties of the selected materials to validate the design.Findings–The results demonstrate that the mechanical strength and deformation characteristics of the suspension components vary according to the applied external loads.The stress and displacement responses of the system were found to be within the allowable limits of the selected materials,confirming the structural integrity and reliability of the design.The suspension set is deemed suitable for the prescribed material and environmental conditions,suggesting potential for practical application in real-world rail systems.Originality/value–This research contributes to the design and optimization of bogie suspension systems using advanced CAD/CAE tools.It thinks that the material selection and numerical validation approach presented here can guide future designs in heavy load rail applications and potentially improve both safety and performance.展开更多
The incorporation of graphene fillers into polymer matrices has been recognized for its potential to enhance thermal conductivity,which is particularly beneficial for applications in thermal management.The uniformity ...The incorporation of graphene fillers into polymer matrices has been recognized for its potential to enhance thermal conductivity,which is particularly beneficial for applications in thermal management.The uniformity of graphene dispersion is pivotal to achieving optimal thermal conductivity,thereby directly influencing the effectiveness of thermal management,including the mitigation of local hot-spot temperatures.This research employs a quantitative approach to assess the distribution of graphene fillers within a PBX(plastic-bonded explosive)matrix,focusing specifically on the thermal management of hot spots.Through finite element method(FEM)simulations,we have explored the impact of graphene filler orientation,proximity to the central heat source,and spatial clustering on heat transfer.Our findings indicate that the strategic distribution of graphene fillers can create efficient thermal conduction channels,which significantly reduce the temperatures at local hot spots.In a model containing 0.336%graphene by volume,the central hot-spot temperature was reduced by approximately 60 K compared to a pure PBX material,under a heat flux of 600 W/m^(2).This study offers valuable insights into the optimization of the spatial arrangement of low-concentration graphene fillers,aiming to improve the thermal management capabilities of HMX-based PBX explosives.展开更多
Purpose–Type-120 relief valves are critical components of locomotive braking systems,and they rapidly discharge the air pressure during brake release to enable swift pressure relief.In order to develop type-120 relie...Purpose–Type-120 relief valves are critical components of locomotive braking systems,and they rapidly discharge the air pressure during brake release to enable swift pressure relief.In order to develop type-120 relief valve rubber diaphragms with long life and high performance,the damaged faulty samples were analyzed and studied.Design/methodology/approach–Finite element analysis(FEA)was used to investigate the stress distribution and failure mechanism of the rubber diaphragms within the type-120 relief valves under dynamic loading conditions.The Ogden hyperelastic constitutive model was used to fit the diaphragm data obtained from the uniaxial tensile tests,and its suitability for the modeling of large deformations was confirmed.Findings–The FEA results indicated that,when the rubber diaphragms reached their maximum deformation,the peak stress on their upper surfaces was 5.44 MPa.Thus,this region is highly susceptible to fatigue damage.The service life of the rubber diaphragms could be extended by using rubber compounds with high tensile moduli or a fabric-reinforced rubber diaphragm.Originality/value–This study provides valuable data and experience for the development of the rubber diaphragms in the type-120 valves and other long-life rubber products in the railway field.展开更多
Microstructure topology evolution during severe plastic deformation(SPD)is crucial for understanding and optimising the mechanical properties of metallic materials,though its prediction remains challenging.Herein,we c...Microstructure topology evolution during severe plastic deformation(SPD)is crucial for understanding and optimising the mechanical properties of metallic materials,though its prediction remains challenging.Herein,we combine discrete cell complexes(DCC),a fully discrete algebraic topology model-with finite element analysis(FEA)to simulate and analyse the microstructure topology of pure copper under SPD.Using DCC,we model the evolution of microstructure topology characterised by Betti numbers(β_(0),β_(1),β_(2))and Euler characteristic(χ).This captures key changes in GBNs and topological features within representative volume elements(RVEs)containing several hundred grains during SPD-induced recrystallisation.As SPD cycles increase,high-angle grain boundaries(HAGBs)progressively form.Topological analysis reveals an overall decrease in β_(0)values,indicating fewer isolated HAGB substructures,while β_(2) values show a steady upward trend,highlighting new grain formation.Leveraging DCC-derived RVE topology and FEA-generated plastic strain data,we directly simulate the evolution and spatial distribution of microstructure topology and HAGB fraction in a copper tube undergoing cyclic parallel tube channel angular pressing(PTCAP),a representative SPD technique.Within the tube,the HAGB fraction continuously increases with PTCAP cycles,reflecting the microstructure’s gradual transition from subgrains to fully-formed grains.Analysis of Betti number distribution and evolution reveals the microstructural reconstruction mechanism underpinning this subgrain to grain transition during PTCAP.We further demonstrate the significant influence of spatially non-uniform plastic strain distribution on microstructure reconstruction kinetics.This study demonstrates a feasible approach for simulating microstructure topology evolution of metals processed by cyclic SPD via the integration of DCC and FEA.展开更多
Serving as the initiating explosive devices between the propellant tank and the engines,metal-based rupture diaphragms are widely used in ramjet igniters owing to the advantages provided by their simple structure,smal...Serving as the initiating explosive devices between the propellant tank and the engines,metal-based rupture diaphragms are widely used in ramjet igniters owing to the advantages provided by their simple structure,small size,and low cost.However,the reliability of rupture pressure directly affects the success of engine ignition and rocket launch,which is mainly influenced by factors like material,structure,and residual thickness of the surface notch of the diaphragm.Among those,the geometry of the notch is easy to define and control when compared to the mechanical parameters of the ruptured diaphragm.Thus,to make the diaphragm rupture(1A30 Al)within the required pressure range(0.4 MPa±3.5%)with highly sensitive and reliability,we draw inspiration from the arthropod’s force-sensitive slit organ which encompasses curved microgrooves to design a Ω-shaped notch for the rupture diaphragm.Finite element analysis is used to study the relationship between the burst pressure and geometric dimension of theΩ-shaped and bioinspired microgroove.Based on that,metal-based rupture diaphragms are fabricated by femtosecond laser processing technology,followed by rupture tests.Experiment results demonstrate that the practical rupture pressure of the diaphragm is highly consistent with the finite element analysis results,which verifies the effectiveness of the bionic design.展开更多
This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is e...This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.展开更多
A modified inner-element edge-based smoothed finite element method(IES-FEM)is developed and integrated with ABAQUS using a user-defined element(UEL)in this study.Initially,the smoothing domain discretization of IES-FE...A modified inner-element edge-based smoothed finite element method(IES-FEM)is developed and integrated with ABAQUS using a user-defined element(UEL)in this study.Initially,the smoothing domain discretization of IES-FEM is described and compared with ES-FEM.A practical modification of IES-FEM is then introduced that used the technique employed by ES-FEM for the nodal strain calculation.The differences in the strain computation among ES-FEM,IES-FEM,and FEM are then discussed.The modified IES-FEM exhibited superior performance in displacement and a slight advantage in stress compared to FEM using the same mesh according to the results obtained from both the regular and irregular elements.The robustness of the IES-FEM to severely deformed meshes was also verified.展开更多
Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the stru...Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the structural safety of supersonic vehicles,but it has been rarely investigated.Given that existing methods are inefficient for high-frequency dynamic analysis in multi-physics fields,the present work addresses this challenge by proposing a Stochastic Energy Finite Element Method(SEFEM).SEFEM uses energy density instead of displacement to describe the dynamic response,thereby significantly enhancing its efficiency.In SEFEM,the effects of aerodynamic and thermal loads on the energy propagation characteristics are studied analytically and incorporated into the energy density governing equation.These effects are also considered when calculating the input power generated by the acoustic load,and two effective approaches named Frequency Response Function Method(FRFM)and Mechanical Impedance Method(MIM)are developed accordingly and integrated into SEFEM.The good accuracy,applicability,and high efficiency of the proposed SEFEM are demonstrated through numerical simulations performed on a two-dimensional panel under aero-thermoacoustic loads.Additionally,the effects and underlying mechanisms of aero-thermo-acoustic loads on the high-frequency response are explored.This work not only presents an efficient approach for predicting high-frequency dynamic response of panels subjected to aero-thermo-acoustic loads,but also provides insights into the high-frequency dynamic characteristics in multi-physics fields.展开更多
Experimental tests are essential for evaluating S-N curves and assessing the fatigue life of welded joints.However,in the case of complex geometries,experimental tests often cannot provide the necessary stress-strain ...Experimental tests are essential for evaluating S-N curves and assessing the fatigue life of welded joints.However,in the case of complex geometries,experimental tests often cannot provide the necessary stress-strain data for specific materials and welded joints.Therefore,finite element(FE)analyses are frequently utilized to assess fatigue behavior in complex geometries and address the discontinuities induced by welding processes.In this study,the fatigue properties of titanium welded joints,produced using an innovative laser source and welded without the use of filler materials,were analyzed through numerical methods.Two different FEmethodswere applied to T-specimens fabricated from Ti6Al4V sheets:the hot-spot stress and notch-stress approach.The FE fatigue life predictions were validated using experimental fatigue test results.The Hot-Spot Stress method yielded a fatigue limit slightly below 100 MPa,demonstrating a consistent slope in the S-N response.Conversely,the Notch Stress method,using a 1 mm fictitious notch radius,indicated a higher fatigue strength corresponding to a range between 225 and 250MPa,providing amore conservative and localized fatigue estimate.Fatigue resistance in welded joints of steel and aluminum is commonly assessed using specific fatigue classes called“Fatigue Strength Classes(FAT)curves”and their associated S-N curves as recommended by the International Institute of Welding(IIW).However,no such FAT class assignments currently exist for titanium alloys.To address this gap,strain-based FAT curves were proposed by normalizing steel FAT curves using titanium’s elastic properties.This strain-based framework enables direct comparison across materials and provides a foundation for fatigue evaluation of titanium weldments.The author proposed a procedure to normalize steel FAT curves considering the different elastic material properties,enabling a comparison with Ti6Al4V data in terms of hot spot strain or notch strain.This approach facilitates the development of a universal framework for strain-based fatigue evaluation across different materials.展开更多
In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow e...In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow equation.The velocity and pressure are computed simultaneously.The accuracy of velocity is improved one order.The concentration equation is solved by using mixed finite element,multi-step difference and upwind approximation.A multi-step method is used to approximate time derivative for improving the accuracy.The upwind approximation and an expanded mixed finite element are adopted to solve the convection and diffusion,respectively.The composite method could compute the diffusion flux and its gradient.It possibly becomes an eficient tool for solving convection-dominated diffusion problems.Firstly,the conservation of mass holds.Secondly,the multi-step method has high accuracy.Thirdly,the upwind approximation could avoid numerical dispersion.Using numerical analysis of a priori estimates and special techniques of differential equations,we give an error estimates for a positive definite problem.Numerical experiments illustrate its computational efficiency and feasibility of application.展开更多
The axial single-pass high temperature compression test of a hot-rolled extra-large heavy H-beam steel continuous casting billet (Q420 steel) under different deformation conditions through the Gleeble-1500D thermomech...The axial single-pass high temperature compression test of a hot-rolled extra-large heavy H-beam steel continuous casting billet (Q420 steel) under different deformation conditions through the Gleeble-1500D thermomechanical simulator was carried out. The modified Johnson–Cook model and the Arrhenius model based on strain-compensated of Q420 steel were established. The latter can more accurately reflect the flow behavior of Q420 steel. For the simulation of thermal compression, dynamic recrystallization (DRX) correlation models were developed and imported into DEFORM-3D software. According to simulation results, high temperatures and low strain rates are conducive to DRX. Due to the uneven distribution of equivalent strain and temperature in different parts of the same section, DRX volume fraction and grain size are unevenly distributed. At the center, the DRX volume fraction is the largest and the grain size is the smallest. The upper and lower edges are vice versa, and the left and right edges are centered. Optical microscopy and electron backscatter diffraction characterization methods were used to study the hot compression microstructure under different deformation conditions. As the deformation amount increases, complete DRX is gradually reached. The original austenite grain gradually becomes smaller. Local average misorientation decreases with the progression of DRX but increases with the amount of deformation after completion of DRX. As the temperature increases and the rate decreases, low angle grain boundaries and medium angle grain boundaries gradually decrease, and high angle grain boundaries gradually increase, indicating that dislocation decreases gradually, DRX grains increase gradually, and martensitic multilayer structure is obvious. As austenite grain size increases, the length of martensite lath increases, and the number of martensite blocks decreases.展开更多
Double-row pile(DRP)retaining systems have been widely used in deep excavations in China.Soil between the front and back-row piles(FBP soil)is often improved to decrease the displacement of DRPs in soft soil areas,but...Double-row pile(DRP)retaining systems have been widely used in deep excavations in China.Soil between the front and back-row piles(FBP soil)is often improved to decrease the displacement of DRPs in soft soil areas,but the improvement efficiency has rarely been researched.A large and deep excavation supported by a DRP retaining system is introduced,and the effect of FBP soil improvement is discussed by comparing the finite element analysis and the monitoring results.Then,a parametric study of DRP using the finite element method considering the small strain of soil is conducted to investigate the effect of FBP soil improvement.It was shown that the pile deflection and bending moment decrease when the FBP soil is improved.Moreover,the most efficient way to minimize the pile deflection and bending moment is to improve the FBP soil around the excavation level.The FBP soil improvement 2-4 m below the pile head is not very useful for reducing the pile deflection and can be eliminated when the pile displacement limit is not very strict.展开更多
文摘Design a precision electroplating mechanical structure for automobiles based on finite element analysis method and analyze its mechanical properties.Taking the automobile steering knuckle as the research object,ABAQUS parametric modeling technology is used to construct its three-dimensional geometric model,and geometric simplification is carried out.Two surface treatment processes,HK-35 zinc nickel alloy electroplating and pure zinc electroplating,were designed,and the influence of different coatings on the mechanical properties of steering knuckles was compared and analyzed through numerical simulation.At the same time,standard specimens were prepared for salt spray corrosion testing and scratch method combined strength testing to verify the numerical simulation results.The results showed that under emergency braking and composite working conditions,the peak Von Mises stress of the zinc nickel alloy coating was 119.85 MPa,which was lower than that of the pure zinc coating and the alkaline electroplated zinc layer.Its equivalent strain value was 652×10^(-6),which was lower than that of the pure zinc coating and the alkaline electroplated zinc layer.Experimental data confirms that zinc nickel alloy coatings exhibit significant advantages in stress distribution uniformity,strain performance,and load-bearing capacity in high stress zones.The salt spray corrosion test further indicates that the coating has superior corrosion resistance and coating substrate interface bonding strength,which can significantly improve the mechanical stability and long-term reliability of automotive precision electroplating mechanical structures.
文摘Objective: To compare the stress distribution in the periodontal ligament under different orthodontic forces during canine distalization using long-arm brackets, and to determine the optimal force value for this device in orthodontic treatment. Methods: A finite element model was constructed after extracting the mandibular first premolar, and a long-arm bracket with a traction height of 6 mm was placed on the labial side of the mandibular canine. Three working conditions of 50 g, 100 g, and 150 g were simulated, and the magnitude and distribution of von Mises stress in the periodontal ligament were compared for each condition. Results: The maximum von Mises stress in the periodontal ligament was 0.013281 MPa in the 50 g condition, 0.02536 MPa in the 100 g condition, and 0.035549 MPa in the 150 g condition. As the orthodontic force increased, the stress distribution area in the periodontal ligament also expanded. Conclusion: A 100 g orthodontic force is the most suitable when using long-arm brackets, providing a relatively uniform stress distribution in the periodontal ligament and keeping the stress within a reasonable range.
基金supported by Scientific Research Projects Department of Istanbul Technical University.Project Number:MGA-2018-41546.Grant receiver:E.T.
文摘Due to their superior properties, the interest in nanostructures is increasing today in engineering. This study presents a new two-noded curved finite element for analyzing the in-plane static behaviors of curved nanobeams. Opposite to traditional curved finite elements developed by using approximate interpolation functions, the proposed curved finite element is developed by using exact analytical solutions. Although this approach was first introduced for analyzing the mechanical behaviors of macro-scale curved beams by adopting the local theory of elasticity, the exact analytical expressions used in this study were obtained from the solutions of governing equations that were expressed via the differential form of the nonlocal theory of elasticity. Therefore, the effects of shear strain and axial extension included in the analytical formulation are also inherited by the curved finite element developed here. The rigidity matrix and the consistent force vector are developed for a circular finite element. To demonstrate the applicability of the method, static analyses of various curved nanobeams subjected to different boundary conditions and loading scenarios are performed, and the obtained results are compared with the exact analytical ones. The presented study provides an accurate and low computational cost method for researchers to investigate the in-plane static behavior of curved nanobeams.
文摘To effectively address the challenge where the speed of tunnel lining construction struggles to match that of tunnel face and inverted arch construction,and to enhance the quality of secondary lining,a new type of skeleton-free,traversing secondary lining trolley has been developed.This trolley features a set of gantries paired with two sets of formwork.The formwork adopts a multi-segment hinged and strengthened design,ensuring its own strength can meet the requirements of secondary lining concrete pouring without relying on the support of the gantries.When retracted,the formwork can be transported by the gantries through another set of formwork in the supporting state,enabling early formwork support,effectively accelerating the construction progress of the tunnel’s secondary lining,and extending the maintenance time of the secondary lining with the formwork.Finite element software modeling was used for simulation calculations,and the results indicate that the structural strength,stiffness,and other performance parameters of the new secondary lining trolley meet the design requirements,verifying the rationality of the design.
基金supported by the National Natural Science Foundation of China(No.52278251)Guizhou Provincial Sciences and Technology Projects(ZK[2022]Key 007).
文摘Identifying the damage and fracture properties of nuclear graphite materials and accurately simulating them are crucial when designing graphite core structures.To simulate the damage evolution and crack propagation of graphite under stress in a finite element model,compression tests on disks and three-point bending tests on center-notched beams for fine-grained graphite(CDI-1D and IG11 graphite)were conducted.During these tests,digital image correlation and electronic speckle pattern interferometry techniques were utilized to observe the surface full-field displacements of the specimens.A segmented finite element inverse analysis method was developed to characterize the graphite’s damage evolution by quantifying the reduction in Young’s modulus with tensile and compressive strains in disk specimens.The fracture energy and bilinear tensile softening curve of the graphite were determined by comparing the load–displacement responses of the three-point bending tests and the finite element simulation.Finally,by combining the identified damage laws with a fracture criterion based on fracture energy,a damage–fracture model was established and used to simulate tensile tests on L-shaped specimens with different fillet radii.Simulations indicate that the damage area at the fillet expands with increasing radius,creating a blunting effect that enhances the load-bearing capacity of the specimens.This damage–fracture model can be applied to simulate graphite components in core structures.
基金supported by the Science and Technology Research and Development Plan of the China State Railway Group Company Limited(No.Q2023J012).
文摘Purpose–The brake pipe system was an essential braking component of the railway freight trains,but the existing E-type sealing rings had problems such as insufficient low-temperature resistance,poor heat stability and short service life.To address these issues,low-phenyl silicone rubber was prepared and tested,and the finite element analysis and experimental studies on the sealing performance of its sealing rings were carried out.Design/methodology/approach–The low-temperature resistance and thermal stability of the prepared lowphenyl silicone rubber were studied using low-temperature tensile testing,differential scanning calorimetry,dynamic thermomechanical analysis and thermogravimetric analysis.The sealing performance of the lowphenyl silicone rubber sealing ring was studied by using finite element analysis software abaqus and experiments.Findings–The prepared low-phenyl silicone rubber sealing ring possessed excellent low-temperature resistance and thermal stability.According to the finite element analysis results,the finish of the flange sealing surface and groove outer edge should be ensured,and extrusion damage should be avoided.The sealing rings were more susceptible to damage in high compression ratio and/or low-temperature environments.When the sealing effect was ensured,a small compression ratio should be selected,and rubbers with hardness and elasticity less affected by temperature should be selected.The prepared low-phenyl silicone rubber sealing ring had zero leakage at both room temperature(RT)and�508C.Originality/value–The innovation of this study is that it provides valuable data and experience for the future development of the sealing rings used in the brake pipe flange joints of the railway freight cars in China.
文摘Total hip arthroplasty for adults with sequelae from childhood hip disorders poses significant challenges due to altered anatomy.The paper published by Oommen et al reviews the essential management strategies for these complex cases.This article explores the integration of finite element analysis(FEA)to enhance surgical precision and outcomes.FEA provides detailed biomechanical insights,aiding in preoperative planning,implant design,and surgical technique optimization.By simulating implant configurations and assessing bone quality,FEA helps in customizing implants and evaluating surgical techniques like subtrochanteric shortening osteotomy.Advanced imaging techniques,such as 3D printing,virtual reality,and augmented reality,further enhance total hip arthroplasty precision.Future research should focus on validating FEA models,developing patient-specific simulations,and promoting multidisciplinary collaboration.Integrating FEA and advanced technologies in total hip arthroplasty can improve functional outcomes,reduce complications,and enhance quality of life for patients with childhood hip disorder sequelae.
文摘The increasing occurrence of sinkholes caused by water main bursts has attracted significant research attention in recent years.This study addresses the gap in evaluating soil blowout stability resulting from water main failures by investigating the three-dimensional stability of blowouts with circular,hemispherical,and spherical openings.Advanced finite element limit analysis(FELA)combined with adaptive meshing is employed to analyze critical factors,including soil cover depth,surcharge pressure,and internal water pressure,that contribute to blowout failure.In addition,dimensionless ratios are used throughout the paper to assess the influence of these factors.Numerical findings are rigorously validated,ensuring reliability and accuracy.Practical design charts are provided to accommodate a wide range of design scenarios,offering valuable guidance for engineers.This study introduces a pioneering sinkhole simulation methodology,leading to the understanding of three-dimensional blowout stability mechanisms.
文摘Purpose–This paper aims to offer a novel viewpoint for improving performance and reliability by developing and optimizing suspension components in a Y25 bogie through material optimization based on wheel–rail interactions under variable load and track conditions.Design/methodology/approach–The suspension system,a critical component ensuring adaptation to road and load conditions in all vehicle types,is especially vital in heavy freight and passenger trains.In this context,the suspension set of the Y25 bogie–commonly used in T€urkiye and Europe–was modelled using CATIAV5,and stress analyses have been performed by way of ANSYS using the finite element analysis(FEA)method.E300-520-M cast steel was selected for the bogie frame,while two different spring steels,61SiCr7 and 51CrV4,were considered for the suspension springs.The modeled system was subjected to numerical analysis under loading conditions.The resulting stresses and displacements were compared with the mechanical properties of the selected materials to validate the design.Findings–The results demonstrate that the mechanical strength and deformation characteristics of the suspension components vary according to the applied external loads.The stress and displacement responses of the system were found to be within the allowable limits of the selected materials,confirming the structural integrity and reliability of the design.The suspension set is deemed suitable for the prescribed material and environmental conditions,suggesting potential for practical application in real-world rail systems.Originality/value–This research contributes to the design and optimization of bogie suspension systems using advanced CAD/CAE tools.It thinks that the material selection and numerical validation approach presented here can guide future designs in heavy load rail applications and potentially improve both safety and performance.
基金supported by the National Natural Science Foundation of China(Grant No.U2330208).
文摘The incorporation of graphene fillers into polymer matrices has been recognized for its potential to enhance thermal conductivity,which is particularly beneficial for applications in thermal management.The uniformity of graphene dispersion is pivotal to achieving optimal thermal conductivity,thereby directly influencing the effectiveness of thermal management,including the mitigation of local hot-spot temperatures.This research employs a quantitative approach to assess the distribution of graphene fillers within a PBX(plastic-bonded explosive)matrix,focusing specifically on the thermal management of hot spots.Through finite element method(FEM)simulations,we have explored the impact of graphene filler orientation,proximity to the central heat source,and spatial clustering on heat transfer.Our findings indicate that the strategic distribution of graphene fillers can create efficient thermal conduction channels,which significantly reduce the temperatures at local hot spots.In a model containing 0.336%graphene by volume,the central hot-spot temperature was reduced by approximately 60 K compared to a pure PBX material,under a heat flux of 600 W/m^(2).This study offers valuable insights into the optimization of the spatial arrangement of low-concentration graphene fillers,aiming to improve the thermal management capabilities of HMX-based PBX explosives.
基金supported by the Science and Technology Research and Development Plan of the China State Railway Group Company Limited(Grant No.N2023J053).
文摘Purpose–Type-120 relief valves are critical components of locomotive braking systems,and they rapidly discharge the air pressure during brake release to enable swift pressure relief.In order to develop type-120 relief valve rubber diaphragms with long life and high performance,the damaged faulty samples were analyzed and studied.Design/methodology/approach–Finite element analysis(FEA)was used to investigate the stress distribution and failure mechanism of the rubber diaphragms within the type-120 relief valves under dynamic loading conditions.The Ogden hyperelastic constitutive model was used to fit the diaphragm data obtained from the uniaxial tensile tests,and its suitability for the modeling of large deformations was confirmed.Findings–The FEA results indicated that,when the rubber diaphragms reached their maximum deformation,the peak stress on their upper surfaces was 5.44 MPa.Thus,this region is highly susceptible to fatigue damage.The service life of the rubber diaphragms could be extended by using rubber compounds with high tensile moduli or a fabric-reinforced rubber diaphragm.Originality/value–This study provides valuable data and experience for the development of the rubber diaphragms in the type-120 valves and other long-life rubber products in the railway field.
基金support from Outstanding Youth Fund of Jiangsu Province(BK20240077)Key Project(Provincial-Municipal Joint)of Jiangsu Province(BK20243044)+2 种基金Fundamental Research Funds for the Central Universities(NE2024001)National Youth Talents Programof Chinaa project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘Microstructure topology evolution during severe plastic deformation(SPD)is crucial for understanding and optimising the mechanical properties of metallic materials,though its prediction remains challenging.Herein,we combine discrete cell complexes(DCC),a fully discrete algebraic topology model-with finite element analysis(FEA)to simulate and analyse the microstructure topology of pure copper under SPD.Using DCC,we model the evolution of microstructure topology characterised by Betti numbers(β_(0),β_(1),β_(2))and Euler characteristic(χ).This captures key changes in GBNs and topological features within representative volume elements(RVEs)containing several hundred grains during SPD-induced recrystallisation.As SPD cycles increase,high-angle grain boundaries(HAGBs)progressively form.Topological analysis reveals an overall decrease in β_(0)values,indicating fewer isolated HAGB substructures,while β_(2) values show a steady upward trend,highlighting new grain formation.Leveraging DCC-derived RVE topology and FEA-generated plastic strain data,we directly simulate the evolution and spatial distribution of microstructure topology and HAGB fraction in a copper tube undergoing cyclic parallel tube channel angular pressing(PTCAP),a representative SPD technique.Within the tube,the HAGB fraction continuously increases with PTCAP cycles,reflecting the microstructure’s gradual transition from subgrains to fully-formed grains.Analysis of Betti number distribution and evolution reveals the microstructural reconstruction mechanism underpinning this subgrain to grain transition during PTCAP.We further demonstrate the significant influence of spatially non-uniform plastic strain distribution on microstructure reconstruction kinetics.This study demonstrates a feasible approach for simulating microstructure topology evolution of metals processed by cyclic SPD via the integration of DCC and FEA.
基金supported by the National Key R&D Program of China(Grant No.2022YFB4601700).
文摘Serving as the initiating explosive devices between the propellant tank and the engines,metal-based rupture diaphragms are widely used in ramjet igniters owing to the advantages provided by their simple structure,small size,and low cost.However,the reliability of rupture pressure directly affects the success of engine ignition and rocket launch,which is mainly influenced by factors like material,structure,and residual thickness of the surface notch of the diaphragm.Among those,the geometry of the notch is easy to define and control when compared to the mechanical parameters of the ruptured diaphragm.Thus,to make the diaphragm rupture(1A30 Al)within the required pressure range(0.4 MPa±3.5%)with highly sensitive and reliability,we draw inspiration from the arthropod’s force-sensitive slit organ which encompasses curved microgrooves to design a Ω-shaped notch for the rupture diaphragm.Finite element analysis is used to study the relationship between the burst pressure and geometric dimension of theΩ-shaped and bioinspired microgroove.Based on that,metal-based rupture diaphragms are fabricated by femtosecond laser processing technology,followed by rupture tests.Experiment results demonstrate that the practical rupture pressure of the diaphragm is highly consistent with the finite element analysis results,which verifies the effectiveness of the bionic design.
基金supported by the National Natural Science Foundation of China(Grant Nos.51890912,51979025 and 52011530189).
文摘This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.
基金the National Natural Science Foundation of China(No.11672238)the 111 Project(No.BP0719007)the Shaanxi Province Natural Science Foundation(No.2020JZ-06)for the financial support.
文摘A modified inner-element edge-based smoothed finite element method(IES-FEM)is developed and integrated with ABAQUS using a user-defined element(UEL)in this study.Initially,the smoothing domain discretization of IES-FEM is described and compared with ES-FEM.A practical modification of IES-FEM is then introduced that used the technique employed by ES-FEM for the nodal strain calculation.The differences in the strain computation among ES-FEM,IES-FEM,and FEM are then discussed.The modified IES-FEM exhibited superior performance in displacement and a slight advantage in stress compared to FEM using the same mesh according to the results obtained from both the regular and irregular elements.The robustness of the IES-FEM to severely deformed meshes was also verified.
基金financially supported by the National Natural Science Foundation of China(Nos.12302228 and 12372170)。
文摘Skin panels on supersonic vehicles are subjected to aero-thermo-acoustic loads,resulting in a well-known multi-physics dynamic problem.The high-frequency dynamic response of these panels significantly impacts the structural safety of supersonic vehicles,but it has been rarely investigated.Given that existing methods are inefficient for high-frequency dynamic analysis in multi-physics fields,the present work addresses this challenge by proposing a Stochastic Energy Finite Element Method(SEFEM).SEFEM uses energy density instead of displacement to describe the dynamic response,thereby significantly enhancing its efficiency.In SEFEM,the effects of aerodynamic and thermal loads on the energy propagation characteristics are studied analytically and incorporated into the energy density governing equation.These effects are also considered when calculating the input power generated by the acoustic load,and two effective approaches named Frequency Response Function Method(FRFM)and Mechanical Impedance Method(MIM)are developed accordingly and integrated into SEFEM.The good accuracy,applicability,and high efficiency of the proposed SEFEM are demonstrated through numerical simulations performed on a two-dimensional panel under aero-thermoacoustic loads.Additionally,the effects and underlying mechanisms of aero-thermo-acoustic loads on the high-frequency response are explored.This work not only presents an efficient approach for predicting high-frequency dynamic response of panels subjected to aero-thermo-acoustic loads,but also provides insights into the high-frequency dynamic characteristics in multi-physics fields.
基金supported by the project PRIN_2022PNRR_P2022Y3PBY_001“MADLEINE,CUP:J53D23015830001”.Project funded under the National Recovery and Resilience Plan(NRRP),Mission 4 Component C2 Investment 1.1 by the European Union-NextGenerationEU.
文摘Experimental tests are essential for evaluating S-N curves and assessing the fatigue life of welded joints.However,in the case of complex geometries,experimental tests often cannot provide the necessary stress-strain data for specific materials and welded joints.Therefore,finite element(FE)analyses are frequently utilized to assess fatigue behavior in complex geometries and address the discontinuities induced by welding processes.In this study,the fatigue properties of titanium welded joints,produced using an innovative laser source and welded without the use of filler materials,were analyzed through numerical methods.Two different FEmethodswere applied to T-specimens fabricated from Ti6Al4V sheets:the hot-spot stress and notch-stress approach.The FE fatigue life predictions were validated using experimental fatigue test results.The Hot-Spot Stress method yielded a fatigue limit slightly below 100 MPa,demonstrating a consistent slope in the S-N response.Conversely,the Notch Stress method,using a 1 mm fictitious notch radius,indicated a higher fatigue strength corresponding to a range between 225 and 250MPa,providing amore conservative and localized fatigue estimate.Fatigue resistance in welded joints of steel and aluminum is commonly assessed using specific fatigue classes called“Fatigue Strength Classes(FAT)curves”and their associated S-N curves as recommended by the International Institute of Welding(IIW).However,no such FAT class assignments currently exist for titanium alloys.To address this gap,strain-based FAT curves were proposed by normalizing steel FAT curves using titanium’s elastic properties.This strain-based framework enables direct comparison across materials and provides a foundation for fatigue evaluation of titanium weldments.The author proposed a procedure to normalize steel FAT curves considering the different elastic material properties,enabling a comparison with Ti6Al4V data in terms of hot spot strain or notch strain.This approach facilitates the development of a universal framework for strain-based fatigue evaluation across different materials.
基金supported by the Natural Science Foundation of Shandong Province(ZR2021MA019)the National Natural Science Foundation of China(11871312)。
文摘In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow equation.The velocity and pressure are computed simultaneously.The accuracy of velocity is improved one order.The concentration equation is solved by using mixed finite element,multi-step difference and upwind approximation.A multi-step method is used to approximate time derivative for improving the accuracy.The upwind approximation and an expanded mixed finite element are adopted to solve the convection and diffusion,respectively.The composite method could compute the diffusion flux and its gradient.It possibly becomes an eficient tool for solving convection-dominated diffusion problems.Firstly,the conservation of mass holds.Secondly,the multi-step method has high accuracy.Thirdly,the upwind approximation could avoid numerical dispersion.Using numerical analysis of a priori estimates and special techniques of differential equations,we give an error estimates for a positive definite problem.Numerical experiments illustrate its computational efficiency and feasibility of application.
基金supported by Topic 3 of the 14th Five-Year National Key Research and Development Plan:Prediction and Control Technology for Hot Rolling Shape-Performance Integration of Ultra Large Size H-beam Steel(Project No.2021YFB3401003).
文摘The axial single-pass high temperature compression test of a hot-rolled extra-large heavy H-beam steel continuous casting billet (Q420 steel) under different deformation conditions through the Gleeble-1500D thermomechanical simulator was carried out. The modified Johnson–Cook model and the Arrhenius model based on strain-compensated of Q420 steel were established. The latter can more accurately reflect the flow behavior of Q420 steel. For the simulation of thermal compression, dynamic recrystallization (DRX) correlation models were developed and imported into DEFORM-3D software. According to simulation results, high temperatures and low strain rates are conducive to DRX. Due to the uneven distribution of equivalent strain and temperature in different parts of the same section, DRX volume fraction and grain size are unevenly distributed. At the center, the DRX volume fraction is the largest and the grain size is the smallest. The upper and lower edges are vice versa, and the left and right edges are centered. Optical microscopy and electron backscatter diffraction characterization methods were used to study the hot compression microstructure under different deformation conditions. As the deformation amount increases, complete DRX is gradually reached. The original austenite grain gradually becomes smaller. Local average misorientation decreases with the progression of DRX but increases with the amount of deformation after completion of DRX. As the temperature increases and the rate decreases, low angle grain boundaries and medium angle grain boundaries gradually decrease, and high angle grain boundaries gradually increase, indicating that dislocation decreases gradually, DRX grains increase gradually, and martensitic multilayer structure is obvious. As austenite grain size increases, the length of martensite lath increases, and the number of martensite blocks decreases.
基金the Key Research Program of Shanghai Construction Group(No.17JCSF-37)。
文摘Double-row pile(DRP)retaining systems have been widely used in deep excavations in China.Soil between the front and back-row piles(FBP soil)is often improved to decrease the displacement of DRPs in soft soil areas,but the improvement efficiency has rarely been researched.A large and deep excavation supported by a DRP retaining system is introduced,and the effect of FBP soil improvement is discussed by comparing the finite element analysis and the monitoring results.Then,a parametric study of DRP using the finite element method considering the small strain of soil is conducted to investigate the effect of FBP soil improvement.It was shown that the pile deflection and bending moment decrease when the FBP soil is improved.Moreover,the most efficient way to minimize the pile deflection and bending moment is to improve the FBP soil around the excavation level.The FBP soil improvement 2-4 m below the pile head is not very useful for reducing the pile deflection and can be eliminated when the pile displacement limit is not very strict.
