To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-r...To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-ray computed tomography were combined to obtain the strain distribution over the sample surface and internal fractures of the samples.The Gini and skewness(G-S)coefficients were used to quantify strain localization during tests,where the Gini coefficient reflects the degree of clustering of elements with high strain values,i.e.,strain localization/delocalization.The strain localization-induced asymmetry of data distribution is quantified by the skewness coefficient.A precursor to granite failure is defined by the rapid and simultaneous increase of the G-S coefficients,which are calculated from strain increment,giving an earlier warning of failure by about 8%peak stress than those from absolute strain values.Moreover,the process of damage accumulation due to stress-driven crack propagation in Beishan granite is different at various confining pressures as the stress exceeds the crack initiation stress.Concretely,strain localization is continuous until brittle failure at higher confining pressure,while both strain localization and delocalization occur at lower confining pressure.Despite the different stress conditions,a similar statistical characteristic of strain localization during the creep stage is observed.The Gini coefficient increases,and the skewness coefficient decreases slightly as the creep stress is below 95%peak stress.When the accelerated strain localization begins,the Gini and skewness coefficients increase rapidly and simultaneously.展开更多
A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relax...A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.展开更多
Iced transmission line galloping poses a significant threat to the safety and reliability of power systems,leading directly to line tripping,disconnections,and power outages.Existing early warning methods of iced tran...Iced transmission line galloping poses a significant threat to the safety and reliability of power systems,leading directly to line tripping,disconnections,and power outages.Existing early warning methods of iced transmission line galloping suffer from issues such as reliance on a single data source,neglect of irregular time series,and lack of attention-based closed-loop feedback,resulting in high rates of missed and false alarms.To address these challenges,we propose an Internet of Things(IoT)empowered early warning method of transmission line galloping that integrates time series data from optical fiber sensing and weather forecast.Initially,the method applies a primary adaptive weighted fusion to the IoT empowered optical fiber real-time sensing data and weather forecast data,followed by a secondary fusion based on a Back Propagation(BP)neural network,and uses the K-medoids algorithm for clustering the fused data.Furthermore,an adaptive irregular time series perception adjustment module is introduced into the traditional Gated Recurrent Unit(GRU)network,and closed-loop feedback based on attentionmechanism is employed to update network parameters through gradient feedback of the loss function,enabling closed-loop training and time series data prediction of the GRU network model.Subsequently,considering various types of prediction data and the duration of icing,an iced transmission line galloping risk coefficient is established,and warnings are categorized based on this coefficient.Finally,using an IoT-driven realistic dataset of iced transmission line galloping,the effectiveness of the proposed method is validated through multi-dimensional simulation scenarios.展开更多
The principle of optical time-domain reflection localization limits the sensing spatial resolution of Raman distributed optical fiber sensing.We provide a solution for a Raman distributed optical fiber sensing system ...The principle of optical time-domain reflection localization limits the sensing spatial resolution of Raman distributed optical fiber sensing.We provide a solution for a Raman distributed optical fiber sensing system with kilometer-level sensing distance and submeter spatial resolution.Based on this,we propose a Raman distributed optical fiber sensing scheme based on chaotic pulse cluster demodulation.Chaotic pulse clusters are used as the probe signal,in preference to conventional pulsed or chaotic single-pulse lasers.Furthermore,the accurate positioning of the temperature variety region along the sensing fiber can be realized using chaotic pulse clusters.The proposed demodulation scheme can enhance the signal-to-noise ratio by improving the correlation between the chaotic reference and the chaotic Raman anti-Stokes scattering signals.The experiment achieved a sensing spatial resolution of 30 cm at a distributed temperature-sensing distance of∼6.0 km.Furthermore,we explored the influence of chaotic pulse width and detector bandwidth on the sensing spatial resolution.In addition,the theoretical experiments proved that the sensing spatial resolution in the proposed scheme was independent of the pulse width and sensing distance.展开更多
Structural deformation monitoring of flight vehicles based on optical fiber sensing(OFS)technology has been a focus of research in the field of aerospace.After nearly 30 years of research and development,Chinese and i...Structural deformation monitoring of flight vehicles based on optical fiber sensing(OFS)technology has been a focus of research in the field of aerospace.After nearly 30 years of research and development,Chinese and international researchers have made significant advances in the areas of theory and methods,technology and systems,and ground experiments and flight tests.These advances have led to the development of OFS technology from the laboratory research stage to the engineering application stage.However,a few problems encountered in practical applications limit the wider application and further development of this technology,and thus urgently require solutions.This paper reviews the history of research on the deformation monitoring of flight vehicles.It examines various aspects of OFS-based deformation monitoring including the main varieties of OFS technology,technical advantages and disadvantages,suitability in aerospace applications,deformation reconstruction algorithms,and typical applications.This paper points out the key unresolved problems and the main evolution paradigms of engineering applications.It further discusses future development directions from the perspectives of an evolution paradigm,standardization,new materials,intelligentization,and collaboration.展开更多
Stimulated Brillouin scattering-induced phase noise is harmful to interferometric fiber sensing systems. The localized fluctuating model is used to study the intensity noise caused by the stimulated Brillouin scatteri...Stimulated Brillouin scattering-induced phase noise is harmful to interferometric fiber sensing systems. The localized fluctuating model is used to study the intensity noise caused by the stimulated Brillouin scattering in a single-mode fiber. The phase noise structure is analyzed for an interferometric fiber sensing system, and an unbalanced Michelson interferometer with an optical path difference of 1 m, as well as the phase-generated carrier technique, is used to measure the phase noise. It is found that the phase noise is small when the input power is below the stimulated Brillouin scattering threshold, increases dramatically at first and then gradually becomes flat when the input power is above the threshold, which is similar to the variation in relative intensity noise. It can be inferred that the increase in phase noise is mainly due to the broadening of the laser linewidth caused by stimulated Brillouin scattering, which is verified through linewidth measurements in the absence and presence of the stimulated Brillouin scattering.展开更多
With the development of high speed railway traffic, the structure health monitoring for high-speed rail is necessary due to the safety issue. Optical fiber sensing technology is one of the options to solve it. Stress ...With the development of high speed railway traffic, the structure health monitoring for high-speed rail is necessary due to the safety issue. Optical fiber sensing technology is one of the options to solve it. Stress vector information is the important index to make more reasonable judgments about railway safety. However, information sensed by lots of commercial optical sensors is scalar. According to the stress filed distribution of rail, this paper proposes a new type of stress vector sensor based on optical fiber sensing cable(OFSC) with a symmetrical seven optical fibers structure and analyzes the relations between angle resolution and distance between adjacent of optical fibers through finite-element software(ANSYS) simulation. Through reasonable distance configuration, the angle resolution of the OFSC can be improved, and thus stress vector information, including the stress magnitude and the angle of stress, can be more accurately obtained. The simulation results are helpful to configure OFSC for angle resolution improvement in actual practice, and increase the safety factor in high speed railway structure health monitoring.展开更多
Hong Kong has a long history of applying masonry retaining walls to provide horizontal platforms and stabilize man-made slopes.Due to the sub-tropical climate,some masonry retaining walls are colonized by trees.Extrem...Hong Kong has a long history of applying masonry retaining walls to provide horizontal platforms and stabilize man-made slopes.Due to the sub-tropical climate,some masonry retaining walls are colonized by trees.Extreme weather,such as typhoons and heavy rains,may cause rupture or root failure of those trees,thus resulting in instability of the retaining walls.A monitoring and warning system for the movement of masonry retaining walls and sway of trees has been designed with the application of fiber Bragg grating(FBG)sensing technology.The monitoring system is also equipped with a solar power system and 4G data transmission devices.The key functions of the proposed monitoring system include remote sensing and data access,early warning,and real-time data visualization.The setups and working principles of the monitoring systems and related transducers are introduced.The feasibility,accuracy,serviceability and reliability of this monitoring system have been checked by in-site calibration tests and four-month monitoring.Besides,a two-level interface has been developed for data visualization.The monitoring results show that the monitored masonry retaining wall had a reversible movement up to 2.5 mm during the monitoring period.Besides,it is found that the locations of the maximum strain on trees depend on the crown spread of trees.展开更多
The distributed fiber optic sensing system,known for its high sensitivity and wide-ranging measurement capabilities,has been widely used in monitoring underground gas pipelines.It primarily serves to perceive vibratio...The distributed fiber optic sensing system,known for its high sensitivity and wide-ranging measurement capabilities,has been widely used in monitoring underground gas pipelines.It primarily serves to perceive vibration signals induced by external events and to effectively provide early warnings of potential intrusion activities.Due to the complexity and diversity of external intrusion events,traditional deep learning methods can achieve event recognition with an average accuracy exceeding 90%.However,these methods rely on large-scale datasets,leading to significant time and labor costs during the data collection process.Additionally,traditional methods perform poorly when faced with the scarcity of low-frequency event samples,making it challenging to address these rare occurrences.To address this issue,this paper proposes a small-sample learning model based on triplet learning for intrusion event recognition.The model employs a 6-way 20-shot support set configuration and utilizes the KNN clustering algorithm to assess the model's performance.Experimental results indicate that the model achieves an average accuracy of 91.6%,further validating the superior performance of the triplet learning model in classifying external intrusion events.Compared to traditional methods,this approach not only effectively reduces the dependence on large-scale datasets but also better addresses the classification of low-frequency event samples,demonstrating significant application potential.展开更多
Despite the extensive use of distributed fiber optic sensing(DFOS)in monitoring underground structures,its potential in detecting structural anomalies,such as cracks and cavities,is still not fully understood.To contr...Despite the extensive use of distributed fiber optic sensing(DFOS)in monitoring underground structures,its potential in detecting structural anomalies,such as cracks and cavities,is still not fully understood.To contribute to the identification of defects in underground structures,this study conducted a four-point bending test of a reinforced concrete(RC)beam and uniaxial loading tests of an RC specimen with local cavities.The experimental results revealed the disparity in DFOS strain spike profiles between these two structural anomalies.The effectiveness of DFOS in the quantification of crack opening displacement(COD)was also demonstrated,even in cases where perfect bonding was not achievable between the cable and structures.In addition,DFOS strain spikes observed in two diaphragm wall panels of a twin circular shaft were also reported.The most probable cause of those spikes was identified as the mechanical behavior associated with local concrete contamination.With the utilization of the strain profiles obtained from laboratory tests and field monitoring,three types of multi-classifiers,based on support vector machine(SVM),random forest(RF),and backpropagation neural network(BP),were employed to classify strain profiles,including crack-induced spikes,non-crack-induced spikes,and non-spike strain profiles.Among these classifiers,the SVM-based classifier exhibited superior performance in terms of accuracy and model robustness.This finding suggests that the SVM-based classifier holds promise as a potential solution for the automatic detection and classification of defects in underground structures during long-term monitoring.展开更多
The commonly used method for estimating crack opening displacement(COD)is based on analytical models derived from strain transferring.However,when large background noise exists in distributed fiber optic sensing(DFOS)...The commonly used method for estimating crack opening displacement(COD)is based on analytical models derived from strain transferring.However,when large background noise exists in distributed fiber optic sensing(DFOS)data,estimating COD through an analytical model is very difficult even if the DFOS data have been denoised.To address this challenge,this study proposes a machine learning(ML)-based methodology to complete rock's COD estimation from establishment of a dataset with one-to-one correspondence between strain sequence and COD to the optimization of ML models.The Bayesian optimization is used via the Hyperopt Python library to determine the appropriate hyper-parameters of four ML models.To ensure that the best hyper-parameters will not be missing,the configuration space in Hyperopt is specified by probability distribution.The four models are trained using DFOS data with minimal noise while being examined on datasets with different noise levels to test their anti-noise robustness.The proposed models are compared each other in terms of goodness of fit and mean squared error.The results show that the Bayesian optimization-based random forest is promising to estimate the COD of rock using noisy DFOS data.展开更多
Coal mining induces changes in the nature of rock and soil bodies,as well as hydrogeological conditions,which can easily trigger the occurrence of geological disasters such as water inrush,movement of the coal seam ro...Coal mining induces changes in the nature of rock and soil bodies,as well as hydrogeological conditions,which can easily trigger the occurrence of geological disasters such as water inrush,movement of the coal seam roof and floor,and rock burst.Transparency in coal mine geological conditions provides technical support for intelligent coal mining and geological disaster prevention.In this sense,it is of great significance to address the requirements for informatizing coal mine geological conditions,dynamically adjust sensing parameters,and accurately identify disaster characteristics so as to prevent and control coal mine geological disasters.This paper examines the various action fields associated with geological disasters in mining faces and scrutinizes the types and sensing parameters of geological disasters resulting from coal seam mining.On this basis,it summarizes a distributed fiber-optic sensing technology framework for transparent geology in coal mines.Combined with the multi-field monitoring characteristics of the strain field,the temperature field,and the vibration field of distributed optical fiber sensing technology,parameters such as the strain increment ratio,the aquifer temperature gradient,and the acoustic wave amplitude are extracted as eigenvalues for identifying rock breaking,aquifer water level,and water cut range,and a multi-field sensing method is established for identifying the characteristics of mining-induced rock mass disasters.The development direction of transparent geology based on optical fiber sensing technology is proposed in terms of the aspects of sensing optical fiber structure for large deformation monitoring,identification accuracy of optical fiber acoustic signals,multi-parameter monitoring,and early warning methods.展开更多
To address the temperature cross-talk issue in detecting heavy metal ions in natural waters, a highly-integrated and fully fiber-optic metal ion sensing system capable of temperature-concentration decoupling measureme...To address the temperature cross-talk issue in detecting heavy metal ions in natural waters, a highly-integrated and fully fiber-optic metal ion sensing system capable of temperature-concentration decoupling measurement has been designed. This system integrates a fluidic detection structure assisted by side-polished fibers(SPFs) with a Sagnac interferometer.展开更多
Phase-sensitive Optical Time-Domain Reflectometer(φ-OTDR)technology facilitates the real-time detection of vibration events along fiber optic cables by analyzing changes in Rayleigh scattering signals.This technology...Phase-sensitive Optical Time-Domain Reflectometer(φ-OTDR)technology facilitates the real-time detection of vibration events along fiber optic cables by analyzing changes in Rayleigh scattering signals.This technology is widely used in applications such as intrusion monitoring and structural health assessments.Traditional signal processing methods,such as Support Vector Machines(SVM)and K-Nearest Neighbors(KNN),have limitations in feature extraction and classification in complex environments.Conversely,a single deep learning model often struggles with capturing long time-series dependencies and mitigating noise interference.In this study,we propose a deep learning model that integrates Convolutional Neural Network(CNN),Long Short-Term Memory Network(LSTM),and Transformer modules,leveraging φ-OTDR technology for distributed fiber vibration sensing event recognition.The hybrid model combines the CNN's capability to extract local features,the LSTM's ability to model temporal dynamics,and the Transformer's proficiency in capturing global dependencies.This integration significantly enhances the accuracy and robustness of event recognition.In experiments involving six types of vibration events,the model consistently achieved a validation accuracy of 0.92,and maintained a validation loss of approximately 0.2,surpassing other models,such as TAM+BiLSTM and CNN+CBAM.The results indicate that the CNN+LSTM+Transformer model is highly effective in handling vibration signal classification tasks in complex scenarios,offering a promising new direction for the application of fiber optic vibration sensing technology.展开更多
Optical fiber sensors are used for sensing micro-cracking in composite and metal materials in aerospace applications. The sensing mechanism is based on the detection of acoustic emission signals, which are known to em...Optical fiber sensors are used for sensing micro-cracking in composite and metal materials in aerospace applications. The sensing mechanism is based on the detection of acoustic emission signals, which are known to emanate from micro-cracks when they grow under further loading. The sensor head consists of a fiber Bragg grating that is capable of detecting acoustic emission signals generated by pencil lead breaking, of frequencies up to 200 kHz.展开更多
With the proposal of a“smart battery,”real-time sensing by rechargeable batteries has become progressively more important in both fundamental research and practical applications.However,many traditional sensing tech...With the proposal of a“smart battery,”real-time sensing by rechargeable batteries has become progressively more important in both fundamental research and practical applications.However,many traditional sensing technologies suffer from low sensitivity,large size,and electromagnetic interference problems,rendering them unusable in the harsh and complicated electrochemical environments of batteries.The optical sensor is an alternative approach to realize multiple-parameter,multiple-point measurements simultaneously.Thus,it has garnered significant attention.Through analyzing these measured parameters,the state of interest can be decoded to monitor a battery's health.This review summarizes current progress in optical sensing techniques for batteries with respect to various sensing parameters,discussing the current limitations of optical fiber sensors as well as directions for their future development.展开更多
The up to date progress of fiber sensing technologies in Tianjin University are proposed in this paper.Fiber-optic temperature sensor based on the interference of selective higher-order modes in circular optical fiber...The up to date progress of fiber sensing technologies in Tianjin University are proposed in this paper.Fiber-optic temperature sensor based on the interference of selective higher-order modes in circular optical fiber is developed.Parallel demodulation for extrinsic Fabry-Perot interferometer(EFPI)and fiber Bragg grating(FBG)sensors is realized based on white light interference.Gas concentration detection is realized based on intra-cavity fiber laser spectroscopy.Polarization maintaining fiber(PMF)is used for distributed position or displacement sensing.Based on the before work and results,we gained National Basic Research Program of China on optical fiber sensing technology and will develop further investigation in this area.展开更多
Soft polymer optical fiber(SPOF)has shown great potential in optical-based wearable and implantable biosensors due to its excellent mechanical properties and optical guiding characteristics.However,the multimodality c...Soft polymer optical fiber(SPOF)has shown great potential in optical-based wearable and implantable biosensors due to its excellent mechanical properties and optical guiding characteristics.However,the multimodality characteristics of SPOF limit their integration with traditional fiber optic sensors.This article introduces for the first time a flexible fiber optic vibration sensor based on laser interference technology,which can be applied to vibration measurement under high stretch conditions.This sensor utilizes elastic optical fibers made of polydimethylsiloxane(PDMS)as sensing elements,combined with phase generating carrier technology,to achieve vibration measurement at 50−260 Hz within the stretch range of 0−42%.展开更多
Fiber optic temperature sensors stand out in a variety of applications due to their small size,chemical resistance,and resistance to electromagnetic interference.The traditional optical fiber temperature sensor direct...Fiber optic temperature sensors stand out in a variety of applications due to their small size,chemical resistance,and resistance to electromagnetic interference.The traditional optical fiber temperature sensor directly places the sensing structure in the temperature to be measured,and uses the thermo-optical effect and thermal expansion effect of the SiO_(2)material that constitutes the sensing structure to achieve measurement,while the thermo-optical coefficient and thermal expansion coefficient of SiO_(2) are very small,which limits the high sensitivity response characteristics of the optical fiber temperature sensing structure.In order to solve the problem of low sensitivity of traditional optical fiber temperature sensors,a Mach-Zehnder interferometric temperature sensor with a liquid-encapsulated tapered microfiber is developed.The sensor converts the temperature change into a change in the refractive index of the liquid material and thus realizes the measurement of temperature.In the range of 25~50℃,as the temperature increases,the wavelength of the transmission spectrum shifts towards shorter wavelengths.Experimental results show that the sensitivity of the liquid encapsulated microfiber interferometric temperature sensor can reach-57.91 nk·nm^(-1).This sensor has great potential for applications in marine environmental monitoring,biomedical diagnosis,and aerospace.展开更多
Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most o...Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.52339001).
文摘To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-ray computed tomography were combined to obtain the strain distribution over the sample surface and internal fractures of the samples.The Gini and skewness(G-S)coefficients were used to quantify strain localization during tests,where the Gini coefficient reflects the degree of clustering of elements with high strain values,i.e.,strain localization/delocalization.The strain localization-induced asymmetry of data distribution is quantified by the skewness coefficient.A precursor to granite failure is defined by the rapid and simultaneous increase of the G-S coefficients,which are calculated from strain increment,giving an earlier warning of failure by about 8%peak stress than those from absolute strain values.Moreover,the process of damage accumulation due to stress-driven crack propagation in Beishan granite is different at various confining pressures as the stress exceeds the crack initiation stress.Concretely,strain localization is continuous until brittle failure at higher confining pressure,while both strain localization and delocalization occur at lower confining pressure.Despite the different stress conditions,a similar statistical characteristic of strain localization during the creep stage is observed.The Gini coefficient increases,and the skewness coefficient decreases slightly as the creep stress is below 95%peak stress.When the accelerated strain localization begins,the Gini and skewness coefficients increase rapidly and simultaneously.
基金support of her postdoctoral research at the GFZ Helmholtz Centre for Geosciences.P.Pan acknowledges the financial support of the National Natural Science Foundation of China(Grant No.52339001)H.Hofmann and Y.Ji acknowledge the financial support of the Helmholtz Association's Initiative and Networking Fund for the Helmholtz Young Investigator Group ARES(contract number VH-NG-1516).
文摘A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.
基金research was funded by Science and Technology Project of State Grid Corporation of China under grant number 5200-202319382A-2-3-XG.
文摘Iced transmission line galloping poses a significant threat to the safety and reliability of power systems,leading directly to line tripping,disconnections,and power outages.Existing early warning methods of iced transmission line galloping suffer from issues such as reliance on a single data source,neglect of irregular time series,and lack of attention-based closed-loop feedback,resulting in high rates of missed and false alarms.To address these challenges,we propose an Internet of Things(IoT)empowered early warning method of transmission line galloping that integrates time series data from optical fiber sensing and weather forecast.Initially,the method applies a primary adaptive weighted fusion to the IoT empowered optical fiber real-time sensing data and weather forecast data,followed by a secondary fusion based on a Back Propagation(BP)neural network,and uses the K-medoids algorithm for clustering the fused data.Furthermore,an adaptive irregular time series perception adjustment module is introduced into the traditional Gated Recurrent Unit(GRU)network,and closed-loop feedback based on attentionmechanism is employed to update network parameters through gradient feedback of the loss function,enabling closed-loop training and time series data prediction of the GRU network model.Subsequently,considering various types of prediction data and the duration of icing,an iced transmission line galloping risk coefficient is established,and warnings are categorized based on this coefficient.Finally,using an IoT-driven realistic dataset of iced transmission line galloping,the effectiveness of the proposed method is validated through multi-dimensional simulation scenarios.
基金supported by the National Natural Science Foundation of China(Grant Nos.U23A20375 and 62075151)the National Key Research and Development Program of China(Grant No.202103021223042).
文摘The principle of optical time-domain reflection localization limits the sensing spatial resolution of Raman distributed optical fiber sensing.We provide a solution for a Raman distributed optical fiber sensing system with kilometer-level sensing distance and submeter spatial resolution.Based on this,we propose a Raman distributed optical fiber sensing scheme based on chaotic pulse cluster demodulation.Chaotic pulse clusters are used as the probe signal,in preference to conventional pulsed or chaotic single-pulse lasers.Furthermore,the accurate positioning of the temperature variety region along the sensing fiber can be realized using chaotic pulse clusters.The proposed demodulation scheme can enhance the signal-to-noise ratio by improving the correlation between the chaotic reference and the chaotic Raman anti-Stokes scattering signals.The experiment achieved a sensing spatial resolution of 30 cm at a distributed temperature-sensing distance of∼6.0 km.Furthermore,we explored the influence of chaotic pulse width and detector bandwidth on the sensing spatial resolution.In addition,the theoretical experiments proved that the sensing spatial resolution in the proposed scheme was independent of the pulse width and sensing distance.
基金funded by the National Natural Science Foundation of China(51705024,51535002,51675053,61903041,61903042,and 61903041)the National Key Research and Development Program of China(2016YFF0101801)+4 种基金the National Hightech Research and Development Program of China(2015AA042308)the Innovative Equipment Pre-Research Key Fund Project(6140414030101)the Manned Space Pre-Research Project(20184112043)the Beijing Municipal Natural Science Foundation(F7202017 and 4204101)the Beijing Nova Program of Science and Technology(Z191100001119052)。
文摘Structural deformation monitoring of flight vehicles based on optical fiber sensing(OFS)technology has been a focus of research in the field of aerospace.After nearly 30 years of research and development,Chinese and international researchers have made significant advances in the areas of theory and methods,technology and systems,and ground experiments and flight tests.These advances have led to the development of OFS technology from the laboratory research stage to the engineering application stage.However,a few problems encountered in practical applications limit the wider application and further development of this technology,and thus urgently require solutions.This paper reviews the history of research on the deformation monitoring of flight vehicles.It examines various aspects of OFS-based deformation monitoring including the main varieties of OFS technology,technical advantages and disadvantages,suitability in aerospace applications,deformation reconstruction algorithms,and typical applications.This paper points out the key unresolved problems and the main evolution paradigms of engineering applications.It further discusses future development directions from the perspectives of an evolution paradigm,standardization,new materials,intelligentization,and collaboration.
基金Project supported by the National Natural Science Foundation of China (Grant No. 61177073)the Open Fund of Key Laboratory of Optoelectronic Information and Sensing Technologies of Guangdong Higher Education Institutes, Jinan University, China (Grant No. gdol201101)+1 种基金the Fund of Innovation of Graduate School of NUDT, China (Grant No. B110703)Hunan Provincial Innovation Foundation for Postgraduate,China (Grant No. CX2011B033)
文摘Stimulated Brillouin scattering-induced phase noise is harmful to interferometric fiber sensing systems. The localized fluctuating model is used to study the intensity noise caused by the stimulated Brillouin scattering in a single-mode fiber. The phase noise structure is analyzed for an interferometric fiber sensing system, and an unbalanced Michelson interferometer with an optical path difference of 1 m, as well as the phase-generated carrier technique, is used to measure the phase noise. It is found that the phase noise is small when the input power is below the stimulated Brillouin scattering threshold, increases dramatically at first and then gradually becomes flat when the input power is above the threshold, which is similar to the variation in relative intensity noise. It can be inferred that the increase in phase noise is mainly due to the broadening of the laser linewidth caused by stimulated Brillouin scattering, which is verified through linewidth measurements in the absence and presence of the stimulated Brillouin scattering.
文摘With the development of high speed railway traffic, the structure health monitoring for high-speed rail is necessary due to the safety issue. Optical fiber sensing technology is one of the options to solve it. Stress vector information is the important index to make more reasonable judgments about railway safety. However, information sensed by lots of commercial optical sensors is scalar. According to the stress filed distribution of rail, this paper proposes a new type of stress vector sensor based on optical fiber sensing cable(OFSC) with a symmetrical seven optical fibers structure and analyzes the relations between angle resolution and distance between adjacent of optical fibers through finite-element software(ANSYS) simulation. Through reasonable distance configuration, the angle resolution of the OFSC can be improved, and thus stress vector information, including the stress magnitude and the angle of stress, can be more accurately obtained. The simulation results are helpful to configure OFSC for angle resolution improvement in actual practice, and increase the safety factor in high speed railway structure health monitoring.
基金supported by the Development Bureau of Hong Kong SAR Government,a Research Impact Fund(RIF)project(Grant No.R5037-18)a Theme-based Research Scheme Fund(TRS)project(Grant No.T22-502/18-R)a General Research Fund(GRF)projects(Grant No.PolyU 152130/19E)from Research Grants Council(RGC)of Hong Kong SAR.
文摘Hong Kong has a long history of applying masonry retaining walls to provide horizontal platforms and stabilize man-made slopes.Due to the sub-tropical climate,some masonry retaining walls are colonized by trees.Extreme weather,such as typhoons and heavy rains,may cause rupture or root failure of those trees,thus resulting in instability of the retaining walls.A monitoring and warning system for the movement of masonry retaining walls and sway of trees has been designed with the application of fiber Bragg grating(FBG)sensing technology.The monitoring system is also equipped with a solar power system and 4G data transmission devices.The key functions of the proposed monitoring system include remote sensing and data access,early warning,and real-time data visualization.The setups and working principles of the monitoring systems and related transducers are introduced.The feasibility,accuracy,serviceability and reliability of this monitoring system have been checked by in-site calibration tests and four-month monitoring.Besides,a two-level interface has been developed for data visualization.The monitoring results show that the monitored masonry retaining wall had a reversible movement up to 2.5 mm during the monitoring period.Besides,it is found that the locations of the maximum strain on trees depend on the crown spread of trees.
基金Supported by the Scientific Research and Technology Development Project of Petrochina Southwest Oil and Gas Field Company(20230307-02)。
文摘The distributed fiber optic sensing system,known for its high sensitivity and wide-ranging measurement capabilities,has been widely used in monitoring underground gas pipelines.It primarily serves to perceive vibration signals induced by external events and to effectively provide early warnings of potential intrusion activities.Due to the complexity and diversity of external intrusion events,traditional deep learning methods can achieve event recognition with an average accuracy exceeding 90%.However,these methods rely on large-scale datasets,leading to significant time and labor costs during the data collection process.Additionally,traditional methods perform poorly when faced with the scarcity of low-frequency event samples,making it challenging to address these rare occurrences.To address this issue,this paper proposes a small-sample learning model based on triplet learning for intrusion event recognition.The model employs a 6-way 20-shot support set configuration and utilizes the KNN clustering algorithm to assess the model's performance.Experimental results indicate that the model achieves an average accuracy of 91.6%,further validating the superior performance of the triplet learning model in classifying external intrusion events.Compared to traditional methods,this approach not only effectively reduces the dependence on large-scale datasets but also better addresses the classification of low-frequency event samples,demonstrating significant application potential.
基金support from the Open Research Project Programme of the State Key Laboratory of Internet of Things for Smart City,University of Macao (Grant No.SKL-IoTSC (UM)-2021-2023/ORPF/A19/2022)the General Research Fund project from Research Grants Council of Hong Kong Special Administrative Region Government of China (Grant No.15214722)the Start-up Fund from The Hong Kong Polytechnic University (Grant No.BD88).
文摘Despite the extensive use of distributed fiber optic sensing(DFOS)in monitoring underground structures,its potential in detecting structural anomalies,such as cracks and cavities,is still not fully understood.To contribute to the identification of defects in underground structures,this study conducted a four-point bending test of a reinforced concrete(RC)beam and uniaxial loading tests of an RC specimen with local cavities.The experimental results revealed the disparity in DFOS strain spike profiles between these two structural anomalies.The effectiveness of DFOS in the quantification of crack opening displacement(COD)was also demonstrated,even in cases where perfect bonding was not achievable between the cable and structures.In addition,DFOS strain spikes observed in two diaphragm wall panels of a twin circular shaft were also reported.The most probable cause of those spikes was identified as the mechanical behavior associated with local concrete contamination.With the utilization of the strain profiles obtained from laboratory tests and field monitoring,three types of multi-classifiers,based on support vector machine(SVM),random forest(RF),and backpropagation neural network(BP),were employed to classify strain profiles,including crack-induced spikes,non-crack-induced spikes,and non-spike strain profiles.Among these classifiers,the SVM-based classifier exhibited superior performance in terms of accuracy and model robustness.This finding suggests that the SVM-based classifier holds promise as a potential solution for the automatic detection and classification of defects in underground structures during long-term monitoring.
基金The Young Scientists Fund of the National Natural Science Foundation of China(Grant No.42407250)the Fund from Research Centre for Resources Engineering towards Carbon Neutrality(RCRE)of The Hong Kong Polytechnic University(Grant No.No.1-BBEM)the Fund from Natural Science Foundation of Jiangsu Province(Grant No.BK20241211)。
文摘The commonly used method for estimating crack opening displacement(COD)is based on analytical models derived from strain transferring.However,when large background noise exists in distributed fiber optic sensing(DFOS)data,estimating COD through an analytical model is very difficult even if the DFOS data have been denoised.To address this challenge,this study proposes a machine learning(ML)-based methodology to complete rock's COD estimation from establishment of a dataset with one-to-one correspondence between strain sequence and COD to the optimization of ML models.The Bayesian optimization is used via the Hyperopt Python library to determine the appropriate hyper-parameters of four ML models.To ensure that the best hyper-parameters will not be missing,the configuration space in Hyperopt is specified by probability distribution.The four models are trained using DFOS data with minimal noise while being examined on datasets with different noise levels to test their anti-noise robustness.The proposed models are compared each other in terms of goodness of fit and mean squared error.The results show that the Bayesian optimization-based random forest is promising to estimate the COD of rock using noisy DFOS data.
基金National Natural Science Foundation of China,Grant/Award Number:42130706。
文摘Coal mining induces changes in the nature of rock and soil bodies,as well as hydrogeological conditions,which can easily trigger the occurrence of geological disasters such as water inrush,movement of the coal seam roof and floor,and rock burst.Transparency in coal mine geological conditions provides technical support for intelligent coal mining and geological disaster prevention.In this sense,it is of great significance to address the requirements for informatizing coal mine geological conditions,dynamically adjust sensing parameters,and accurately identify disaster characteristics so as to prevent and control coal mine geological disasters.This paper examines the various action fields associated with geological disasters in mining faces and scrutinizes the types and sensing parameters of geological disasters resulting from coal seam mining.On this basis,it summarizes a distributed fiber-optic sensing technology framework for transparent geology in coal mines.Combined with the multi-field monitoring characteristics of the strain field,the temperature field,and the vibration field of distributed optical fiber sensing technology,parameters such as the strain increment ratio,the aquifer temperature gradient,and the acoustic wave amplitude are extracted as eigenvalues for identifying rock breaking,aquifer water level,and water cut range,and a multi-field sensing method is established for identifying the characteristics of mining-induced rock mass disasters.The development direction of transparent geology based on optical fiber sensing technology is proposed in terms of the aspects of sensing optical fiber structure for large deformation monitoring,identification accuracy of optical fiber acoustic signals,multi-parameter monitoring,and early warning methods.
基金supported by the National Natural Science Foundation of China(Nos.61705027,62375031 and 52075131)the Chongqing Science and Technology Commission Basic Research Project(No.CSTC-2020jcyj-msxm0603)the Chongqing Municipal Education Commission Science and Technology Research Program(No.KJQN202000609)。
文摘To address the temperature cross-talk issue in detecting heavy metal ions in natural waters, a highly-integrated and fully fiber-optic metal ion sensing system capable of temperature-concentration decoupling measurement has been designed. This system integrates a fluidic detection structure assisted by side-polished fibers(SPFs) with a Sagnac interferometer.
基金Supported by Key Laboratory of Space Active Optical-Electro Technology of Chinese Academy of Sciences(2021ZDKF4)。
文摘Phase-sensitive Optical Time-Domain Reflectometer(φ-OTDR)technology facilitates the real-time detection of vibration events along fiber optic cables by analyzing changes in Rayleigh scattering signals.This technology is widely used in applications such as intrusion monitoring and structural health assessments.Traditional signal processing methods,such as Support Vector Machines(SVM)and K-Nearest Neighbors(KNN),have limitations in feature extraction and classification in complex environments.Conversely,a single deep learning model often struggles with capturing long time-series dependencies and mitigating noise interference.In this study,we propose a deep learning model that integrates Convolutional Neural Network(CNN),Long Short-Term Memory Network(LSTM),and Transformer modules,leveraging φ-OTDR technology for distributed fiber vibration sensing event recognition.The hybrid model combines the CNN's capability to extract local features,the LSTM's ability to model temporal dynamics,and the Transformer's proficiency in capturing global dependencies.This integration significantly enhances the accuracy and robustness of event recognition.In experiments involving six types of vibration events,the model consistently achieved a validation accuracy of 0.92,and maintained a validation loss of approximately 0.2,surpassing other models,such as TAM+BiLSTM and CNN+CBAM.The results indicate that the CNN+LSTM+Transformer model is highly effective in handling vibration signal classification tasks in complex scenarios,offering a promising new direction for the application of fiber optic vibration sensing technology.
文摘Optical fiber sensors are used for sensing micro-cracking in composite and metal materials in aerospace applications. The sensing mechanism is based on the detection of acoustic emission signals, which are known to emanate from micro-cracks when they grow under further loading. The sensor head consists of a fiber Bragg grating that is capable of detecting acoustic emission signals generated by pencil lead breaking, of frequencies up to 200 kHz.
基金the support from the National Key R&D Program of China(2021YFB2400300)the National Natural Science Foundation of China(Nos.51972131 and 5202780089).
文摘With the proposal of a“smart battery,”real-time sensing by rechargeable batteries has become progressively more important in both fundamental research and practical applications.However,many traditional sensing technologies suffer from low sensitivity,large size,and electromagnetic interference problems,rendering them unusable in the harsh and complicated electrochemical environments of batteries.The optical sensor is an alternative approach to realize multiple-parameter,multiple-point measurements simultaneously.Thus,it has garnered significant attention.Through analyzing these measured parameters,the state of interest can be decoded to monitor a battery's health.This review summarizes current progress in optical sensing techniques for batteries with respect to various sensing parameters,discussing the current limitations of optical fiber sensors as well as directions for their future development.
基金This work was supported by National Basic Research Program of China(973 Program)under Grant No.2010CB327800.
文摘The up to date progress of fiber sensing technologies in Tianjin University are proposed in this paper.Fiber-optic temperature sensor based on the interference of selective higher-order modes in circular optical fiber is developed.Parallel demodulation for extrinsic Fabry-Perot interferometer(EFPI)and fiber Bragg grating(FBG)sensors is realized based on white light interference.Gas concentration detection is realized based on intra-cavity fiber laser spectroscopy.Polarization maintaining fiber(PMF)is used for distributed position or displacement sensing.Based on the before work and results,we gained National Basic Research Program of China on optical fiber sensing technology and will develop further investigation in this area.
文摘Soft polymer optical fiber(SPOF)has shown great potential in optical-based wearable and implantable biosensors due to its excellent mechanical properties and optical guiding characteristics.However,the multimodality characteristics of SPOF limit their integration with traditional fiber optic sensors.This article introduces for the first time a flexible fiber optic vibration sensor based on laser interference technology,which can be applied to vibration measurement under high stretch conditions.This sensor utilizes elastic optical fibers made of polydimethylsiloxane(PDMS)as sensing elements,combined with phase generating carrier technology,to achieve vibration measurement at 50−260 Hz within the stretch range of 0−42%.
文摘Fiber optic temperature sensors stand out in a variety of applications due to their small size,chemical resistance,and resistance to electromagnetic interference.The traditional optical fiber temperature sensor directly places the sensing structure in the temperature to be measured,and uses the thermo-optical effect and thermal expansion effect of the SiO_(2)material that constitutes the sensing structure to achieve measurement,while the thermo-optical coefficient and thermal expansion coefficient of SiO_(2) are very small,which limits the high sensitivity response characteristics of the optical fiber temperature sensing structure.In order to solve the problem of low sensitivity of traditional optical fiber temperature sensors,a Mach-Zehnder interferometric temperature sensor with a liquid-encapsulated tapered microfiber is developed.The sensor converts the temperature change into a change in the refractive index of the liquid material and thus realizes the measurement of temperature.In the range of 25~50℃,as the temperature increases,the wavelength of the transmission spectrum shifts towards shorter wavelengths.Experimental results show that the sensitivity of the liquid encapsulated microfiber interferometric temperature sensor can reach-57.91 nk·nm^(-1).This sensor has great potential for applications in marine environmental monitoring,biomedical diagnosis,and aerospace.
基金funding support from the Israeli Ministry of Housing and Construction(Grant No.2028286).
文摘Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.
