In this study,an experimental study and numerical calculations using fiber model were conducted for four high-strength concrete shear walls with boundary columns under low cyclic load.The boundary column and shear wal...In this study,an experimental study and numerical calculations using fiber model were conducted for four high-strength concrete shear walls with boundary columns under low cyclic load.The boundary column and shear wall were divided into fiber elements,and PERFORM-3D finite element analysis software was used to carry out push-over analysis on the test specimens.The results show that the finite element analysis results were in good agreement with the experimental results.The proposed analysis method could perform elasto-plastic analysis on the high-strength concrete shear wall with boundary columns without distinguishing the categories of frame column and shear wall.The seismic performance of high-strength concrete shear wall with boundary columns was analyzed using the following parameters:axis compression ratio,height to width ratio,ratio of vertical reinforcement,and ratio of longitudinal reinforcement in the boundary column.The results show that the increase in the axial compression ratio causes the bearing capacity of the shear wall to increase at first and then to decrease and causes the ductility to decrease.The increase in the height to width ratio causes the bearing capacity of the shear wall to decrease and its ductility to increase.The ratio of vertical reinforcement was found to have little effect on the bearing capacity and ductility.The increase in the ratio of longitudinal reinforcement in boundary column resulted in a significant increase in the bearing capacity and caused the ductility to decrease at first and then to slowly increase.展开更多
The longitudinal compressive failure of a unidirectional carbon fiber reinforced plastic (CFRP) was studied using multiple-fiber model composites. Aligned carbon fibers were embedded in an epoxy matrix and put on a re...The longitudinal compressive failure of a unidirectional carbon fiber reinforced plastic (CFRP) was studied using multiple-fiber model composites. Aligned carbon fibers were embedded in an epoxy matrix and put on a rectangular beam. A compression test of the model composite was performed by means of a four point bending test of the rectangular beam. The number of carbon fibers was changed from one to several thousands, by which the effect on compressive failure modes was investigated. A compressive failure of a single-fiber model composite was fiber crush. The fiber crush strain was much higher than the compressive failure strain of the unidirectional carbon fiber reinforced plastic. By contrast, a compressive failure of a multiple-fiber model composite was kink-band. The longitudinal compressive failure mechanism shifted from fiber crush to kink-band due to an increasing number of fibers. Kink-band parameters i.e. kink-band angle and kink-band width were dependent on the number of closely-aligned carbon fibers.展开更多
Photosensitivity behavior of H2-loaded silica fiber was modeled by rate equations for activated particles. The theoretical deductions give a close explanation to experimental phenomena on post-exposure growth in fiber...Photosensitivity behavior of H2-loaded silica fiber was modeled by rate equations for activated particles. The theoretical deductions give a close explanation to experimental phenomena on post-exposure growth in fiber gratings.展开更多
A numerical model was developed to study the time dynamics of photo luminescence emitted by Tb^3+doped multimode chalcogenide-selenide glass fibers pumped by laser light at approximately 2μm.The model consists of a s...A numerical model was developed to study the time dynamics of photo luminescence emitted by Tb^3+doped multimode chalcogenide-selenide glass fibers pumped by laser light at approximately 2μm.The model consists of a set of partial differential equations(PDEs),which describe the temporal and spatial evolution of the photon density and level populations within the fiber.In order to solve numerically the PDEs a method of lines was applied.The modeling parameters were extracted from measurements and from data available in the literature.The numerical results obtained support experimental observations.In particular,the developed model reproduces the discrepancies that are observed between the photoluminescence decay curves obtained from different points along the fiber.The numerical analysis was also used to explain the source of these discrepancies.展开更多
Three different kinds of closure model of fiber orientation tensors were applied to simulate numerically the hydrodynamic stability of fiber suspensions in a channel flow. The effects of closure models and three_dimen...Three different kinds of closure model of fiber orientation tensors were applied to simulate numerically the hydrodynamic stability of fiber suspensions in a channel flow. The effects of closure models and three_dimensional (3_D) orientation distribution of fibers on the results of stability analysis were examined. It is found that the relationship of the behavior in hydrodynamic stability and the parameter of the fiber given by all the three models are the same. However, the attenuation of flow instability is most distinct using 3_D hybrid model because the orientation of the fiber departures from the flow direction, and least apparent using its 2_D counterpart for that the fibers show a tendency towards alignment with the flow direction in this case.展开更多
This study tested an improved fiber tracking algorithm, which was based on fiber assignment using a continuous tracking algorithm and a two-tensor model. Different models and tracking decisions were used by judging th...This study tested an improved fiber tracking algorithm, which was based on fiber assignment using a continuous tracking algorithm and a two-tensor model. Different models and tracking decisions were used by judging the type of estimation of each voxel. Thismethod should solve the cross-track problem. This study included eight healthy subjects, two axonal injury patients and seven demyelinating disease patients. This new algorithm clearly exhibited a difference in nerve fiber direction between axonal injury and demyelinating disease patients and healthy control subjects. Compared with fiber assignment with a continuous tracking algorithm, our novel method can track more and longer nerve fibers, and also can solve the fiber crossing problem.展开更多
A quantum chain model of multiple molecule motors is proposed as a mathematical physics theory for the microscopic modeling of classical force-velocity relation and tension transients in muscle fibers. The proposed mo...A quantum chain model of multiple molecule motors is proposed as a mathematical physics theory for the microscopic modeling of classical force-velocity relation and tension transients in muscle fibers. The proposed model was a quantum many-particle Hamiltonian to predict the force-velocity relation for the slow release of muscle fibers, which has not yet been empirically defined and was much more complicated than the hyperbolic relationships. Using the same Hamiltonian model, a mathematical force-velocity relationship was proposed to explain the tension observed when the muscle was stimulated with an alternative electric current. The discrepancy between input electric frequency and the muscle oscillation frequency could be explained physically by the Doppler effect in this quantum chain model. Further more, quantum physics phenomena were applied to explore the tension time course of cardiac muscle and insect flight muscle. Most of the experimental tension transient curves were found to correspond to the theoretical output of quantum two- and three-level models. Mathematical modeling electric stimulus as photons exciting a quantum three-level particle reproduced most of the tension transient curves of water bug Lethocerus maximus.展开更多
The aim of this study is to present a constitutive model for prediction of the mechanical behavior of fiberreinforced cemented sand. For this purpose, a generalized plasticity constitutive model of sandy soil is selec...The aim of this study is to present a constitutive model for prediction of the mechanical behavior of fiberreinforced cemented sand. For this purpose, a generalized plasticity constitutive model of sandy soil is selected and the parameters of the model are determined for three types of sandy soils using the results of triaxial tests. Next, the proposed model is developed using the existing models based on the physicomechanical characteristics of fiber-reinforced cemented sand. The elastic parameters, flow rule and hardening law of the base model are modified for fiber-reinforced cemented sand. To verify the proposed model, the predicted results are compared with those of triaxial tests performed on fiber-reinforced cemented sand. Finally, the efficiency of the proposed model is studied at different confining pressures, and cement and fiber contents.展开更多
Crop performance is determined by the combined effects of the genotype of the crop and the environmental conditions of the production system. This study was undertaken to develop a dynamic model for simulating environ...Crop performance is determined by the combined effects of the genotype of the crop and the environmental conditions of the production system. This study was undertaken to develop a dynamic model for simulating environmental （temperature and solar radiation） and N supply effects on fiber fineness, maturity and micronaire. Three different experiments involving genotypes, sowing dates, and N fertilization rates were conducted to support model development and model evaluation. The growth and development duration of fiber fineness, maturity, and micronaire were scaled by using physiological development time of secondary wall synthesis （PDT SWSP ）, which was determined based on the constant ratio of SWSP/ BMP. PTP （product of relative thermal effectiveness （RTE） and photosynthetically active radiation （PAR）, MJ m-2） and subtending leaf N content per unit area （N A , g m-2） and critical subtending leaf N content per unit area （CN A , g m-2） of cotton boll were calculated or simulated to evaluate effects of temperature and radiation, and N supply. Besides, the interactions among temperature, radiation and N supply were also explained by piecewise function. The overall performance of the model was calibrated and validated with independent data sets from three field experiments with two sowing dates, three or five flowering dates and three or four N fertilization rates for three subsequent years （2005, 2007, and 2009） at three ecological locations. The average RMSE and RE for fiber fineness, maturity, and micronaire predictions were 372 m g-1 and 5.0%, 0.11 m g-1 and 11.4%, 0.3 m g-1 and 12.3%, respectively, indicating a good fit between the simulated and observed data. It appears that the model can give a reliable prediction for fiber fineness, maturity and micronaire formation under various growing conditions.展开更多
The consolidation process of SiC<sub>f</sub>/Ti-6Al-4V composites by matrix-coated fiber (MCF) method via hot pressing was investigated using finite element modeling (FEM). By analyzing the elastic–plasti...The consolidation process of SiC<sub>f</sub>/Ti-6Al-4V composites by matrix-coated fiber (MCF) method via hot pressing was investigated using finite element modeling (FEM). By analyzing the elastic–plastic contact deformation of the representative aligned coated fibers, the consolidation maps delineating the time–temperature–pressure relationship for full densification were constructed. Both the flow coefficient and the contact area coefficient used to describe the contact deformation were calculated according to the model. In addition, the effect of fiber content on matrix stress distribution was analyzed. The results show that fiber content is a significant factor that influences the densification process. Higher fiber content will lower the consolidation rate.展开更多
The accuracy and effi ciency of the modelling techniques utilized to model the nonlinear behavior of structural components is a signifi cant issue in earthquake engineering. In this study, the suffi ciency of three di...The accuracy and effi ciency of the modelling techniques utilized to model the nonlinear behavior of structural components is a signifi cant issue in earthquake engineering. In this study, the suffi ciency of three diff erent modelling techniques that can be employed to simulate the structural behavior of columns is investigated. A fi ber-based fi nite length plastic hinge (FB-FLPH) model is calibrated in this study. In order to calibrate the FB-FLPH model, a novel database of the cyclic behavior of hollow steel columns under simultaneous axial and lateral loading cycles with varying amplitudes is used. By employing the FB-FLPH model calibrated in this study, the interaction of the axial force and the bending moment in columns is directly taken into account, and the deterioration in the cyclic behavior of these members is implicitly considered. The superiority of the calibrated FB-FLPH modelling approach is examined compared with the cases in which conventional fi ber-based distributed plasticity and concentrated plasticity models are utilized. The effi ciency of the enumerated modelling techniques is probed when they are implemented to model the columns of a typical special moment frame in order to prove the advantage of the FB-FLPH modelling approach.展开更多
Objective: The goal of this study was to simulate the application of the dietary recommendations to increase dietary fiber (DF)-containing foods. Methods: This study used 24-hour dietary recalls from NHANES 2003-2006 ...Objective: The goal of this study was to simulate the application of the dietary recommendations to increase dietary fiber (DF)-containing foods. Methods: This study used 24-hour dietary recalls from NHANES 2003-2006 to model the impact of different approaches of increasing DF with current dietary patterns of US adults 19 + years: 1) increased all DF-containing foods by 10, 25, 50, or 100%;2) increased DF content of low DF grain products to a good (2.5 g/serving) or an excellent source level (5.0 g/serving);and 3) increased intake of whole grain foods to meet the recommendation of one-half of total grain. Results: Increasing DF-containing foods by 10, 25, 50, or 100% increased DF intake to 16.9, 18.9, 22.1, and 29.5 g/d, respectively with a concomitant increase in energy of 104, 260, 521, 1042 kcal/d, respectively. Adding 2.5 or 5.0 g/serving DF to low DF grain foods to result in DF intakes of 24.7 and 39.1 g/day, respectively without increased energy. Increasing consumption of whole grain foods increased DF intake to 25.3 g/day but with an additional 1266 kcal/d. Conclusions: Adding additional DF to existing grain-based foods may be a reasonable approach to getting more DF, without increased energy, in the American diet.展开更多
An elastic analysis of an internal central crack with bridging fibers parallel to the free surface in an infinite orthotropic anisotropic elastic plane was performed. A dynamic model of bridging fiber pull-out of comp...An elastic analysis of an internal central crack with bridging fibers parallel to the free surface in an infinite orthotropic anisotropic elastic plane was performed. A dynamic model of bridging fiber pull-out of composite materials was presented. Resultingly the fiber failure is governed by maximum tensile stress, the fiber breaks and hence the crack extension should occur in self-similar fashion. By the methods of complex functions, the problem studied can be transformed into the dynamic model to the Reimann-Hilbert mixed boundary value problem, and a straightforward and easy analytical solution is presented. Analytical study on the crack propagation subjected to a ladder load and an instantaneous pulse loading is obtained respectively for orthotropic anisotropic body. By utilizing the solution, the concrete solutions of this model are attained by ways of superposition.展开更多
The sensitivity of the interferometric fiber optic gyro in the presence of time varying thermal gradients plays a key role in its performance. It is well known that this sensitivity is due to the difference of index c...The sensitivity of the interferometric fiber optic gyro in the presence of time varying thermal gradients plays a key role in its performance. It is well known that this sensitivity is due to the difference of index changes between the points symmetrical with respect to the middle of the coil. In order to reduce this sensitivity, different winding patterns, such as quadrupolar winding, were introduced to keep the thermal environment of the symmetrical points. In this paper, a numerical model of the transient temperature distribution in the gyro was established. The temperature gradient of the coil was solved in conjugation with the nature convection heat transfer in the aperture between the coil and the case. Effects of the winding pattern and the design of its case were investigated to optimize the design of the interferometric fiber optic gyro.展开更多
An ultrasonic sensitivity-improved fiber-optic Fabry-Perot interferometer （FPI） is proposed and employed for ultra- sonic imaging of seismic physical models （SPMs）. The FPI comprises a flexible ultra-thin gold fil...An ultrasonic sensitivity-improved fiber-optic Fabry-Perot interferometer （FPI） is proposed and employed for ultra- sonic imaging of seismic physical models （SPMs）. The FPI comprises a flexible ultra-thin gold film and the end face of a graded-index multimode fiber （MMF）, both of which are enclosed in a ceramic tube. The MMF in a specified length can collimate the diverged light beam and compensate for the light loss inside the air cavity, leading to an increased spectral fringe visibility and thus a steeper spectral slope. By using the spectral sideband filtering technique, the collimated FP1 shows an improved ultrasonic response. Moreover, two-dimensional images of two SPMs are achieved in air by recon- structing the pulse-echo signals through using the time-of-flight approach. The proposed sensor with easy fabrication and compact size can be a good candidate for high-sensitivity and high-precision nondestructive testing of SPMs.展开更多
Centrifugal model testsare playing an increasingly importantrolein investigating slope characteristics under rainfall conditions. However, conventional electronic transducers usually fail during centrifugal model test...Centrifugal model testsare playing an increasingly importantrolein investigating slope characteristics under rainfall conditions. However, conventional electronic transducers usually fail during centrifugal model tests because of the impacts of limitedtest space, high centrifugal force, and presence of water, with the result that limited valid data is obtained. In this study, Fiber Bragg Grating(FBG) sensing technology is employed in the design and development of displacement gauge, an anchor force gauge and an anti-slide pile moment gauge for use on centrifugal model slopes with and without a retaining structure. The two model slopes were installed and monitored at a centrifugal acceleration of 100 g. The test results show that the sensors developed succeed in capturing the deformation and retaining structure mechanical response of the model slopes during and after rainfall. The deformation curvefor the slope without retaining structure shows a steepresponse that turns gradualfor the slope with retaining structure. Importantly, for the slope with the retaining structure, results suggest that more attention be paid to increase of anchor force and antislide pile moment during rainfall. This study verifies the effectiveness of FBG sensing technology in centrifuge research and presents a new and innovative method for slope model testing under rainfall conditions.展开更多
Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random d...Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random distribution of the reinforcement phase in the matrix are not considered in detail, which makes the characteristics of the cutting model significantly different from the actual processing conditions. In this paper, a novel three-phase model of carbon fiber/cyanate ester composites is proposed to simulate the machining damage of the composites. The periodic random distribution of the carbon fiber reinforced phase in the matrix was realized using a double perturbation algorithm. To achieve the stochastic distribution of the strength of a single carbon fiber, a novel method that combines the Weibull intensity distribution theory with the Monte Carlo method is presented. The mechanical properties of the cyanate matrix were characterized by fitting the stress-strain curves, and the cohesive zone model was employed to simulate the interface. Based on the model, the machining damage mechanism of the composites was revealed using finite element simulations and by conducting a theoretical analysis. Furthermore, the milling surfaces of the composites were observed using a scanning electron microscope, to verify the accuracy of the simulation results. In this study, the simulations and theoretical analysis of the carbon fiber/cyanate ester composite processing were carried out based on a novel three-phase model, which revealed the material failure and machining damage mechanism more accurately.展开更多
In an effort to find the effect of mass transfer, surface tension and drag forces on the velocity distribution, the mathematical model of the velocity profile of a nascent hollow fiber during membrane formation in the...In an effort to find the effect of mass transfer, surface tension and drag forces on the velocity distribution, the mathematical model of the velocity profile of a nascent hollow fiber during membrane formation in the air gap region was numerically simulated by using the Runge-Kutta method (fourth-order method). The effect of mass transfer on velocity distribution based on the complicated function (G(Cs h)) was presented and the effects of a complicated function were studied in two cases: in the first case, G(Cs h) was constant; in the second, G(Cs h) was variable. The latter was done by varying with the concentration of solvent in a nascent hollow fiber through the air-gap region. One empirical equation was used to describe this change and the predicted values had a better agreement with the experimental values. To verify the model hypotheses, hollow fiber membranes were spun from 20∶80 polybenzimidazole/polyetherimide dopes with 25.6 wt% solid in N, N-dimethylacetamide (DMAc) using water as the external and internal coagulants. Based on the experimental results of dry-jet wet-spinning process for the fabrication of hollow fiber membranes, it is found that the model calculated values were in a good agreement with the experimental values.展开更多
Polytetrafluoroethylene reinforced with glass fibers is a composite material widely used in industry mainly for the manufacture of seals at the level of the rotary shafts of vehicles and stationary floor machines such...Polytetrafluoroethylene reinforced with glass fibers is a composite material widely used in industry mainly for the manufacture of seals at the level of the rotary shafts of vehicles and stationary floor machines such as turbines and compressors. However, due to elastic and viscous-plastic properties of this material, it wears quickly under the influence of some external parameters during operation. There are therefore material loss, increased clearance and loss of sealing. This work summarises a series of tests carried out with this material in order to analyse the variation of the friction coefficient due to the roughness of the work piece brought into contact with the PTFE, the linear velocity of contact between them and material yield strength. To do this analysis, we used the method of unconventional design of experiments to model the behaviour of material and consequently make decisions to reduce this wear. The results are shown and deeply analysed in the following text as a polynomial mathematical model, graphs, contours and response surfaces illustrating the holding of this material under the effect of the three parameters mentioned above. The previous PTFE samples enriched with chopped glass fibers are not subjected to axially force this time, contrary to the force applied radially. The advantage of this method is the relative linear velocity at the contact sample-disc and the applied pressure remains constant. Under the action of the weight “P” applied on the sample, it comes into friction with the rotating disc whose roughness changes from experience to another;it is expressed by the values of Ra. Tangential friction force appears at the point of contact and is equilibrated by measured force Fm on the lever. The calculation of the moment relative bench axis caused by 2 forces gives the coefficient of friction. Knowing the values of frictional force Ft by calculation and the weight P, we determine then the friction coefficient.展开更多
Refractometric fiber optic sensors have a number of applications in industry due to advantages like remote sensing ability, compact size, easy to fit, etc. A refractometric sensor contains a pair of parallel fibers an...Refractometric fiber optic sensors have a number of applications in industry due to advantages like remote sensing ability, compact size, easy to fit, etc. A refractometric sensor contains a pair of parallel fibers and a gap between the sensor probe and reflector, wherein the liquid whose refractive index is to be measured is filled. This paper describes the importance of mathematical modeling of this sensor. Ray tracing approach is used to model the sensor mathematically. This mathematical model is generalized for any scenario which is useful to avoid tedious trial and error techniques to design the sensor prototype. Mathematical modelling is a useful tool to optimize the gap distance for a detection of refractive index of liquid. The model is developed and analyzed rigorously considering adulteration of diesel by kerosene where refractive index varies from 1.44 to 1.46. Simulation experiments are carried out to optimize the gap distance which is found to be 6.8 mm using both models. Experiments are carried out where sensor probe is fabricated and results are analyzed. It is observed that for suggested gap distance sensor output varies almost linear over the entire range.展开更多
基金supported by the National Natural Science Foundation of China(No.51708209)Hunan Provincial Natural Science Foundation of China(No.2019JJ50209)National Student‘s Program for Innovation and Entrepreneurship(No.201912658001)。
文摘In this study,an experimental study and numerical calculations using fiber model were conducted for four high-strength concrete shear walls with boundary columns under low cyclic load.The boundary column and shear wall were divided into fiber elements,and PERFORM-3D finite element analysis software was used to carry out push-over analysis on the test specimens.The results show that the finite element analysis results were in good agreement with the experimental results.The proposed analysis method could perform elasto-plastic analysis on the high-strength concrete shear wall with boundary columns without distinguishing the categories of frame column and shear wall.The seismic performance of high-strength concrete shear wall with boundary columns was analyzed using the following parameters:axis compression ratio,height to width ratio,ratio of vertical reinforcement,and ratio of longitudinal reinforcement in the boundary column.The results show that the increase in the axial compression ratio causes the bearing capacity of the shear wall to increase at first and then to decrease and causes the ductility to decrease.The increase in the height to width ratio causes the bearing capacity of the shear wall to decrease and its ductility to increase.The ratio of vertical reinforcement was found to have little effect on the bearing capacity and ductility.The increase in the ratio of longitudinal reinforcement in boundary column resulted in a significant increase in the bearing capacity and caused the ductility to decrease at first and then to slowly increase.
文摘The longitudinal compressive failure of a unidirectional carbon fiber reinforced plastic (CFRP) was studied using multiple-fiber model composites. Aligned carbon fibers were embedded in an epoxy matrix and put on a rectangular beam. A compression test of the model composite was performed by means of a four point bending test of the rectangular beam. The number of carbon fibers was changed from one to several thousands, by which the effect on compressive failure modes was investigated. A compressive failure of a single-fiber model composite was fiber crush. The fiber crush strain was much higher than the compressive failure strain of the unidirectional carbon fiber reinforced plastic. By contrast, a compressive failure of a multiple-fiber model composite was kink-band. The longitudinal compressive failure mechanism shifted from fiber crush to kink-band due to an increasing number of fibers. Kink-band parameters i.e. kink-band angle and kink-band width were dependent on the number of closely-aligned carbon fibers.
文摘Photosensitivity behavior of H2-loaded silica fiber was modeled by rate equations for activated particles. The theoretical deductions give a close explanation to experimental phenomena on post-exposure growth in fiber gratings.
基金Project supported by the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Sklodowska-Curie grant agreement No.665778(National Science Centre,Poland,Polonez Fellowship 2016/21/P/ST7/03666)
文摘A numerical model was developed to study the time dynamics of photo luminescence emitted by Tb^3+doped multimode chalcogenide-selenide glass fibers pumped by laser light at approximately 2μm.The model consists of a set of partial differential equations(PDEs),which describe the temporal and spatial evolution of the photon density and level populations within the fiber.In order to solve numerically the PDEs a method of lines was applied.The modeling parameters were extracted from measurements and from data available in the literature.The numerical results obtained support experimental observations.In particular,the developed model reproduces the discrepancies that are observed between the photoluminescence decay curves obtained from different points along the fiber.The numerical analysis was also used to explain the source of these discrepancies.
基金ProjectsupportedbytheNationalNaturalScienceFoundationofChina (No .1 0 3 72 0 90 )
文摘Three different kinds of closure model of fiber orientation tensors were applied to simulate numerically the hydrodynamic stability of fiber suspensions in a channel flow. The effects of closure models and three_dimensional (3_D) orientation distribution of fibers on the results of stability analysis were examined. It is found that the relationship of the behavior in hydrodynamic stability and the parameter of the fiber given by all the three models are the same. However, the attenuation of flow instability is most distinct using 3_D hybrid model because the orientation of the fiber departures from the flow direction, and least apparent using its 2_D counterpart for that the fibers show a tendency towards alignment with the flow direction in this case.
基金supported by Xiamen Technology Projects Grand (The study of chronic cerebrovascular insufficiently in Magnetic Resonance Imaging), No.3502Z20084028
文摘This study tested an improved fiber tracking algorithm, which was based on fiber assignment using a continuous tracking algorithm and a two-tensor model. Different models and tracking decisions were used by judging the type of estimation of each voxel. Thismethod should solve the cross-track problem. This study included eight healthy subjects, two axonal injury patients and seven demyelinating disease patients. This new algorithm clearly exhibited a difference in nerve fiber direction between axonal injury and demyelinating disease patients and healthy control subjects. Compared with fiber assignment with a continuous tracking algorithm, our novel method can track more and longer nerve fibers, and also can solve the fiber crossing problem.
基金Project supported by the Fundamental Research Foundation for the Central Universities of China
文摘A quantum chain model of multiple molecule motors is proposed as a mathematical physics theory for the microscopic modeling of classical force-velocity relation and tension transients in muscle fibers. The proposed model was a quantum many-particle Hamiltonian to predict the force-velocity relation for the slow release of muscle fibers, which has not yet been empirically defined and was much more complicated than the hyperbolic relationships. Using the same Hamiltonian model, a mathematical force-velocity relationship was proposed to explain the tension observed when the muscle was stimulated with an alternative electric current. The discrepancy between input electric frequency and the muscle oscillation frequency could be explained physically by the Doppler effect in this quantum chain model. Further more, quantum physics phenomena were applied to explore the tension time course of cardiac muscle and insect flight muscle. Most of the experimental tension transient curves were found to correspond to the theoretical output of quantum two- and three-level models. Mathematical modeling electric stimulus as photons exciting a quantum three-level particle reproduced most of the tension transient curves of water bug Lethocerus maximus.
文摘The aim of this study is to present a constitutive model for prediction of the mechanical behavior of fiberreinforced cemented sand. For this purpose, a generalized plasticity constitutive model of sandy soil is selected and the parameters of the model are determined for three types of sandy soils using the results of triaxial tests. Next, the proposed model is developed using the existing models based on the physicomechanical characteristics of fiber-reinforced cemented sand. The elastic parameters, flow rule and hardening law of the base model are modified for fiber-reinforced cemented sand. To verify the proposed model, the predicted results are compared with those of triaxial tests performed on fiber-reinforced cemented sand. Finally, the efficiency of the proposed model is studied at different confining pressures, and cement and fiber contents.
基金funded by the National Natural Science Foundation of China (30771277 and 30771279)
文摘Crop performance is determined by the combined effects of the genotype of the crop and the environmental conditions of the production system. This study was undertaken to develop a dynamic model for simulating environmental （temperature and solar radiation） and N supply effects on fiber fineness, maturity and micronaire. Three different experiments involving genotypes, sowing dates, and N fertilization rates were conducted to support model development and model evaluation. The growth and development duration of fiber fineness, maturity, and micronaire were scaled by using physiological development time of secondary wall synthesis （PDT SWSP ）, which was determined based on the constant ratio of SWSP/ BMP. PTP （product of relative thermal effectiveness （RTE） and photosynthetically active radiation （PAR）, MJ m-2） and subtending leaf N content per unit area （N A , g m-2） and critical subtending leaf N content per unit area （CN A , g m-2） of cotton boll were calculated or simulated to evaluate effects of temperature and radiation, and N supply. Besides, the interactions among temperature, radiation and N supply were also explained by piecewise function. The overall performance of the model was calibrated and validated with independent data sets from three field experiments with two sowing dates, three or five flowering dates and three or four N fertilization rates for three subsequent years （2005, 2007, and 2009） at three ecological locations. The average RMSE and RE for fiber fineness, maturity, and micronaire predictions were 372 m g-1 and 5.0%, 0.11 m g-1 and 11.4%, 0.3 m g-1 and 12.3%, respectively, indicating a good fit between the simulated and observed data. It appears that the model can give a reliable prediction for fiber fineness, maturity and micronaire formation under various growing conditions.
基金financially supported by the National Natural Science Foundation of China(Nos.51071122 and51271147)
文摘The consolidation process of SiC<sub>f</sub>/Ti-6Al-4V composites by matrix-coated fiber (MCF) method via hot pressing was investigated using finite element modeling (FEM). By analyzing the elastic–plastic contact deformation of the representative aligned coated fibers, the consolidation maps delineating the time–temperature–pressure relationship for full densification were constructed. Both the flow coefficient and the contact area coefficient used to describe the contact deformation were calculated according to the model. In addition, the effect of fiber content on matrix stress distribution was analyzed. The results show that fiber content is a significant factor that influences the densification process. Higher fiber content will lower the consolidation rate.
文摘The accuracy and effi ciency of the modelling techniques utilized to model the nonlinear behavior of structural components is a signifi cant issue in earthquake engineering. In this study, the suffi ciency of three diff erent modelling techniques that can be employed to simulate the structural behavior of columns is investigated. A fi ber-based fi nite length plastic hinge (FB-FLPH) model is calibrated in this study. In order to calibrate the FB-FLPH model, a novel database of the cyclic behavior of hollow steel columns under simultaneous axial and lateral loading cycles with varying amplitudes is used. By employing the FB-FLPH model calibrated in this study, the interaction of the axial force and the bending moment in columns is directly taken into account, and the deterioration in the cyclic behavior of these members is implicitly considered. The superiority of the calibrated FB-FLPH modelling approach is examined compared with the cases in which conventional fi ber-based distributed plasticity and concentrated plasticity models are utilized. The effi ciency of the enumerated modelling techniques is probed when they are implemented to model the columns of a typical special moment frame in order to prove the advantage of the FB-FLPH modelling approach.
文摘Objective: The goal of this study was to simulate the application of the dietary recommendations to increase dietary fiber (DF)-containing foods. Methods: This study used 24-hour dietary recalls from NHANES 2003-2006 to model the impact of different approaches of increasing DF with current dietary patterns of US adults 19 + years: 1) increased all DF-containing foods by 10, 25, 50, or 100%;2) increased DF content of low DF grain products to a good (2.5 g/serving) or an excellent source level (5.0 g/serving);and 3) increased intake of whole grain foods to meet the recommendation of one-half of total grain. Results: Increasing DF-containing foods by 10, 25, 50, or 100% increased DF intake to 16.9, 18.9, 22.1, and 29.5 g/d, respectively with a concomitant increase in energy of 104, 260, 521, 1042 kcal/d, respectively. Adding 2.5 or 5.0 g/serving DF to low DF grain foods to result in DF intakes of 24.7 and 39.1 g/day, respectively without increased energy. Increasing consumption of whole grain foods increased DF intake to 25.3 g/day but with an additional 1266 kcal/d. Conclusions: Adding additional DF to existing grain-based foods may be a reasonable approach to getting more DF, without increased energy, in the American diet.
文摘An elastic analysis of an internal central crack with bridging fibers parallel to the free surface in an infinite orthotropic anisotropic elastic plane was performed. A dynamic model of bridging fiber pull-out of composite materials was presented. Resultingly the fiber failure is governed by maximum tensile stress, the fiber breaks and hence the crack extension should occur in self-similar fashion. By the methods of complex functions, the problem studied can be transformed into the dynamic model to the Reimann-Hilbert mixed boundary value problem, and a straightforward and easy analytical solution is presented. Analytical study on the crack propagation subjected to a ladder load and an instantaneous pulse loading is obtained respectively for orthotropic anisotropic body. By utilizing the solution, the concrete solutions of this model are attained by ways of superposition.
文摘The sensitivity of the interferometric fiber optic gyro in the presence of time varying thermal gradients plays a key role in its performance. It is well known that this sensitivity is due to the difference of index changes between the points symmetrical with respect to the middle of the coil. In order to reduce this sensitivity, different winding patterns, such as quadrupolar winding, were introduced to keep the thermal environment of the symmetrical points. In this paper, a numerical model of the transient temperature distribution in the gyro was established. The temperature gradient of the coil was solved in conjugation with the nature convection heat transfer in the aperture between the coil and the case. Effects of the winding pattern and the design of its case were investigated to optimize the design of the interferometric fiber optic gyro.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61735014,61327012,and 61275088)the Scientific Research Program Funded by Shaanxi Provincial Education Department,China(Grant No.08JZ58)the Northwest University Graduate Innovation and Creativity Funds,China(Grant No.YZZ17088)
文摘An ultrasonic sensitivity-improved fiber-optic Fabry-Perot interferometer （FPI） is proposed and employed for ultra- sonic imaging of seismic physical models （SPMs）. The FPI comprises a flexible ultra-thin gold film and the end face of a graded-index multimode fiber （MMF）, both of which are enclosed in a ceramic tube. The MMF in a specified length can collimate the diverged light beam and compensate for the light loss inside the air cavity, leading to an increased spectral fringe visibility and thus a steeper spectral slope. By using the spectral sideband filtering technique, the collimated FP1 shows an improved ultrasonic response. Moreover, two-dimensional images of two SPMs are achieved in air by recon- structing the pulse-echo signals through using the time-of-flight approach. The proposed sensor with easy fabrication and compact size can be a good candidate for high-sensitivity and high-precision nondestructive testing of SPMs.
基金supported by the National Natural Science Foundation of China (Grant Nos.41502299,41372306)Research Planning of Sichuan Education Department, China (Grant No.16ZB0105)State Key Laboratory of Geohazard Prevention and Geoenvironment Protection Independent Research Project (SKLGP2016Z007)
文摘Centrifugal model testsare playing an increasingly importantrolein investigating slope characteristics under rainfall conditions. However, conventional electronic transducers usually fail during centrifugal model tests because of the impacts of limitedtest space, high centrifugal force, and presence of water, with the result that limited valid data is obtained. In this study, Fiber Bragg Grating(FBG) sensing technology is employed in the design and development of displacement gauge, an anchor force gauge and an anti-slide pile moment gauge for use on centrifugal model slopes with and without a retaining structure. The two model slopes were installed and monitored at a centrifugal acceleration of 100 g. The test results show that the sensors developed succeed in capturing the deformation and retaining structure mechanical response of the model slopes during and after rainfall. The deformation curvefor the slope without retaining structure shows a steepresponse that turns gradualfor the slope with retaining structure. Importantly, for the slope with the retaining structure, results suggest that more attention be paid to increase of anchor force and antislide pile moment during rainfall. This study verifies the effectiveness of FBG sensing technology in centrifuge research and presents a new and innovative method for slope model testing under rainfall conditions.
基金Supported by Research Innovation Fund Project “Research on micro machining mechanism of fiber reinforced composites”(Grant No.HIT.NSRIF.2014055)of Harbin Institute of Technology,China
文摘Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random distribution of the reinforcement phase in the matrix are not considered in detail, which makes the characteristics of the cutting model significantly different from the actual processing conditions. In this paper, a novel three-phase model of carbon fiber/cyanate ester composites is proposed to simulate the machining damage of the composites. The periodic random distribution of the carbon fiber reinforced phase in the matrix was realized using a double perturbation algorithm. To achieve the stochastic distribution of the strength of a single carbon fiber, a novel method that combines the Weibull intensity distribution theory with the Monte Carlo method is presented. The mechanical properties of the cyanate matrix were characterized by fitting the stress-strain curves, and the cohesive zone model was employed to simulate the interface. Based on the model, the machining damage mechanism of the composites was revealed using finite element simulations and by conducting a theoretical analysis. Furthermore, the milling surfaces of the composites were observed using a scanning electron microscope, to verify the accuracy of the simulation results. In this study, the simulations and theoretical analysis of the carbon fiber/cyanate ester composite processing were carried out based on a novel three-phase model, which revealed the material failure and machining damage mechanism more accurately.
文摘In an effort to find the effect of mass transfer, surface tension and drag forces on the velocity distribution, the mathematical model of the velocity profile of a nascent hollow fiber during membrane formation in the air gap region was numerically simulated by using the Runge-Kutta method (fourth-order method). The effect of mass transfer on velocity distribution based on the complicated function (G(Cs h)) was presented and the effects of a complicated function were studied in two cases: in the first case, G(Cs h) was constant; in the second, G(Cs h) was variable. The latter was done by varying with the concentration of solvent in a nascent hollow fiber through the air-gap region. One empirical equation was used to describe this change and the predicted values had a better agreement with the experimental values. To verify the model hypotheses, hollow fiber membranes were spun from 20∶80 polybenzimidazole/polyetherimide dopes with 25.6 wt% solid in N, N-dimethylacetamide (DMAc) using water as the external and internal coagulants. Based on the experimental results of dry-jet wet-spinning process for the fabrication of hollow fiber membranes, it is found that the model calculated values were in a good agreement with the experimental values.
文摘Polytetrafluoroethylene reinforced with glass fibers is a composite material widely used in industry mainly for the manufacture of seals at the level of the rotary shafts of vehicles and stationary floor machines such as turbines and compressors. However, due to elastic and viscous-plastic properties of this material, it wears quickly under the influence of some external parameters during operation. There are therefore material loss, increased clearance and loss of sealing. This work summarises a series of tests carried out with this material in order to analyse the variation of the friction coefficient due to the roughness of the work piece brought into contact with the PTFE, the linear velocity of contact between them and material yield strength. To do this analysis, we used the method of unconventional design of experiments to model the behaviour of material and consequently make decisions to reduce this wear. The results are shown and deeply analysed in the following text as a polynomial mathematical model, graphs, contours and response surfaces illustrating the holding of this material under the effect of the three parameters mentioned above. The previous PTFE samples enriched with chopped glass fibers are not subjected to axially force this time, contrary to the force applied radially. The advantage of this method is the relative linear velocity at the contact sample-disc and the applied pressure remains constant. Under the action of the weight “P” applied on the sample, it comes into friction with the rotating disc whose roughness changes from experience to another;it is expressed by the values of Ra. Tangential friction force appears at the point of contact and is equilibrated by measured force Fm on the lever. The calculation of the moment relative bench axis caused by 2 forces gives the coefficient of friction. Knowing the values of frictional force Ft by calculation and the weight P, we determine then the friction coefficient.
文摘Refractometric fiber optic sensors have a number of applications in industry due to advantages like remote sensing ability, compact size, easy to fit, etc. A refractometric sensor contains a pair of parallel fibers and a gap between the sensor probe and reflector, wherein the liquid whose refractive index is to be measured is filled. This paper describes the importance of mathematical modeling of this sensor. Ray tracing approach is used to model the sensor mathematically. This mathematical model is generalized for any scenario which is useful to avoid tedious trial and error techniques to design the sensor prototype. Mathematical modelling is a useful tool to optimize the gap distance for a detection of refractive index of liquid. The model is developed and analyzed rigorously considering adulteration of diesel by kerosene where refractive index varies from 1.44 to 1.46. Simulation experiments are carried out to optimize the gap distance which is found to be 6.8 mm using both models. Experiments are carried out where sensor probe is fabricated and results are analyzed. It is observed that for suggested gap distance sensor output varies almost linear over the entire range.
