This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to ex...This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to examine the deterioration mechanisms caused by freeze-thaw cycles and sulfate erosion. The results show that compressive and tensile strengths increase with basalt fiber dosage. The optimal dosage is 0.2%. With longer exposure to sulfate erosion, both strengths decline significantly. Basalt fibers effectively bridge cracks, control expansion, enhance compactness, and improve concrete performance. Ultra-low-temperature freeze-thaw cycles and sulfate erosion cause rapid crack growth. Sulfate erosion produces crystallization products and expansive substances. These fill cracks, create pressure, and damage the internal structure. Freezing and expansion forces further enlarge voids and cracks. This provides space for expansive substances, worsening concrete deterioration and reducing its performance.展开更多
Sizing treatment is a suitable technique to modify the fiber-matrix interfaces without damage of inherent performance of fibers.In this work,sizing agents based on Janus particles(JPs)were utilized to enhance the inte...Sizing treatment is a suitable technique to modify the fiber-matrix interfaces without damage of inherent performance of fibers.In this work,sizing agents based on Janus particles(JPs)were utilized to enhance the interface of basalt fiber(BF)/poly(vinyl chloride)(PVC)composites.polystyrene/poly(butyl acrylate)(PS/PBA)@silica JPs were synthesized by seed emulsion polymerization and three different sizing agents were prepared for BF sizing treatment.JPs with organic soft sphere and inorganic hard hemisphere enhanced the interfaces through their amphiphilicity,chemical bonding and mechanical interlock.The mechanical properties of composite with JPs sizing treated BFs performed better when there was one JPs layer modified on the interface.According to the intermitting bonding and gradient modulus theory,JPs patterned interfaces are ideal transition layers between high modulus BF and low modulus PVC.展开更多
Basalt fibers/7075 aluminum matrix composites were studied to meet the demand of aluminum alloy drill pipes for material wear resistance.The composites with different basalt fiber additions were prepared by hot presse...Basalt fibers/7075 aluminum matrix composites were studied to meet the demand of aluminum alloy drill pipes for material wear resistance.The composites with different basalt fiber additions were prepared by hot pressed sintering and hot extrusion.The mechanical properties as well as friction and wear properties of the composites were studied by microstructure analysis,tensile experiments,friction and wear experiments.The results showed that basalt fibers were oriented and uniformly distributed and led to local grain refinement in the alloy matrix.The hardness and elongation of the composites were improved.The friction coefficient of the composites increased and then decreased,and the maximum wear depth and wear amount decreased,then increased,then decreased again with the growth of basalt fiber addition.Meanwhile,the inclusion of basalt fibers mitigated the uneven wear of the extruded 7075 aluminum alloy.The value of wear depth difference of 7075-0.2BF was the smallest,and that of 7075-2.0BF was close to it.The maximum wear depth and wear volume the 7075-0.2BF and 7075-2.0BF were also the smallest.The inhibition of uneven wear by basalt fibers enhanced of wear resistance for 7075 aluminum alloy,which has reference significance for improving the performance of aluminum alloy drill pipes.展开更多
To discuss the pavement performance of basalt fiber-modified asphalt mixtures,the optimum dosages of asphalt and fibers are studied by the Marshall test and the rutting test.The results demonstrate that the optimum do...To discuss the pavement performance of basalt fiber-modified asphalt mixtures,the optimum dosages of asphalt and fibers are studied by the Marshall test and the rutting test.The results demonstrate that the optimum dosages of asphalt and fibers are 4.63% and 0.3%,respectively.Then the pavement performances of basalt（polyester,xylogen）fiber-modified asphalt mixtures are investigated through high temperature stability tests,water stability tests and low temperature crack resistance tests.It indicates that the pavement performances of the fiber-modified asphalt mixtures such as rutting dynamic stability,freezing splitting tensile strength,low temperature crack resistance and so on are improved compared with control asphalt mixture.The results show that the pavement performances of asphalt mixtures can be improved by fiber-modifiers.Besides,the improvement effects of basalt fiber are superior to polyester fiber and xylogen fiber.展开更多
The fatigue property of asphalt mixtures under complicated environment （low-temperature bending performance, chloride penetration, freezing-thawing cycle and their coupling effect） and the improvement effect for rel...The fatigue property of asphalt mixtures under complicated environment （low-temperature bending performance, chloride penetration, freezing-thawing cycle and their coupling effect） and the improvement effect for relevant property of basalt fiber-reinforcing asphalt mixture under complicated environment are studied. Two grading types of asphalt mixtures, AC-16I and AC-13I, are chosen, whose optimum asphalt-aggregate ratio and optimum dosage of basalt fiber are determined by the Marshall test. The standard specimens are made firstly, and then the low temperature bending tests of asphalt mixture and basalt fiber-reinforced asphalt mixture under the coupling effect of the chloride erosion and freezing-thawing cycle have been carried out. Finally, the fatigue property tests of asphalt mixture and basalt fiber-reinforced asphalt mixture under complex environment are performed on MTS material testing system. The results indicate that the tensile strength, the maximum curving tensile stress, the curving stiffness modulus, and fatigue properties of asphalt mixture are influenced by the coupling effect of the chloride erosion and freezing-thawing cycle. The low-temperature bending performance and fatigue property of asphalt mixtures under complicated environment can be greatly improved by adding moderate basalt fiber. The dense gradation asphalt mixture possesses stronger ability to resist adverse environmental effects under the same condition.展开更多
This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high ther...This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high thermal resistance,corrosion resistance and economic cost.To test mechanical properties and failure modes of flexural members strengthened with BFRP,flexural experiment is conducted on four two-span T-section continuous beams strengthened with BFRP and one un-strengthened comparative beam.The experimental result shows that the strengthened beams perform remarkably in terms of yield strength,ultimate strength and ductility.BFRP has good prospects in retrofitting and strengthening of concrete structures which require good ductility and corrosion resistance.展开更多
To study the applicability of the basalt fiber through various experimental works in thermal and chemical environments, glass fiber and carbon fiber were compared and discussed. The tensile strength testing was used t...To study the applicability of the basalt fiber through various experimental works in thermal and chemical environments, glass fiber and carbon fiber were compared and discussed. The tensile strength testing was used to investigate the corrosive resistance of basalt fiber, meanwhile, surface study by scanning electron microscopy and microanalysis with complementary X-ray diffraction analysis （SEM/EDS） was also used to ascertain the durability of basalt fiber. The basalt fiber showed better strength retention than the glass fiber at relatively high temperature. Its tensile strength increased when exposed at 300 ~C for several hours, and still maintain about 70% of the initial strength at 400 ~C, whereas that of the glass fiber decreased dramatically. The better stability of the basalt fiber was observed in hydrothermal and chemical environment. The tensile strength of the basalt fiber increased by 20% after the immersion in boiling water and remained well in acid solution, when it comes to glass fiber, the tensile strength decreased to some extent. Although the alkali resistance of basalt fiber was poor at the initial stage, it shows better resistance than the glass fiber after long time treatment.展开更多
A valid strategy to tailor the properties of polylactic acid for more extensive applications was introducing filler.In this work,basalt fiber assembled with in-situ SiO_(2) nanoparticles on the surface was successfull...A valid strategy to tailor the properties of polylactic acid for more extensive applications was introducing filler.In this work,basalt fiber assembled with in-situ SiO_(2) nanoparticles on the surface was successfully prepared via hydrothermal method and it was further treated with coupling agent KH-550 to improve interfacial interaction between polylactic acid(PLA)and basalt fibers(BF).It was demonstrated that the introduction of BFS could increase the crystallization of PLA and resulted in forming trans-crystallization based on TG and DSC results.The tensile strength of PLA/BF composites raised from 39 MPa to 62.5 MPa with increasing the fiber loading from 1 wt%to 10 wt%.Furthermore,the interfacial interaction could be effectively improved by assembling SiO_(2)(especially with 250 nm in diameter)on BF surface to build mechanical locking,which could keep the PLA matrix in place during the mechanical deformation with the tensile strength value raised from 62.5 MPa to 74.0 MPa.It is noticeable that the impact and flexural properties were effectively increased with the incorporation of in-situ SiO_(2) nanoparticles.The further KH-550 treatment made a positive impact as well.For instance,the impact strength and flexural strength of the sample with SiO_(2) and KH-550 modification were improved to 22.49 k J/m^(2) and 146.83 MPa and it enhanced about 42.16%and 41.04%than those of neat PLA,respectively.Therefore,an efficient enhancement of mechanical performance was achieved and this concept of assembling in-situ SiO_(2) on silica-based fiber as a modifier was a novel and simple path to design the interfacial construction and properties of the polymer composites.展开更多
The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and t...The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and the repeated creep tests. The results show that basalt fiber has excellent reinforced performances, such as high asphalt absorption ratio, low water absorption ratio, high tensile strength, high elastic modulus and high temperature stability. The rutting factor of the fiber reinforced asphalt mastic is higher than the plain asphalt mastic and the reinforced effects are more remarkable under high temperature. The rheological performances of the asphalt mastic demonstrate a good linear relationship between different temperature and loading frequency. The creep stiffness modulus of the asphalt mastic at different loading time can be expressed by power function. Improved Burgers model is used to represent the rheological behaviors of the asphalt mastic with basalt fiber and the model parameters are estimated.展开更多
In this investigation, basalt mineral fiber softening agent was prepared in order to obtain desirable flexible performance. Stability and physical chemistry natures of softening agent were evaluated by particle size d...In this investigation, basalt mineral fiber softening agent was prepared in order to obtain desirable flexible performance. Stability and physical chemistry natures of softening agent were evaluated by particle size distribution, dilution, storage and folding endurance etc. Constitutes of basalt and wood fibers were determined by energy dispersion analysis X-ray which served as an accessory of scanning electron microscopy (SEM-EDAX). Naturally degradable ecocomposite was prepared by basalt and wood fibers. The results of SEM observation illustrated that the wood and basalt fibers were blended uniformly. The impact factors of beating degree, content of wood fibers and adhesive etc. were discussed. The structure of the naturally degradable ecocomposite was contrasted with that of pure wood fibers and the cause of excellent filtration performance was analyzed. Compared with traditional methods, it was of saving wood resource, a large amount of water and reducing second pollution. As a consequence, the ecocomposite harmonized with environment and accorded with requirement of benignly friendly environment.展开更多
Continuous basalt fiber(CBF)is an outstanding inorganic fiber produced from nature,which has a wide range of applications in the field of armor protection of national defense military.However,the mechanical response a...Continuous basalt fiber(CBF)is an outstanding inorganic fiber produced from nature,which has a wide range of applications in the field of armor protection of national defense military.However,the mechanical response and failure mechanism of 3D printed CBF reinforced components are still not well understood.Here,the 3D printing thermoplastic composites with high volume fraction CBF have been successfully prepared by fused deposition modelling(FDM)method.The effects of fiber printing direction and polymer matrix type on the tensile and flexural properties of the 3D printed composites have been explored,and the detailed failure morphology has been characterized using scanning electron microscopy and optical microscopy.It was found that under high fiber volume fraction,3D printed CBF reinforced polyamides(PA)composites have the best ability to maintain material integrity of the composites,followed by acrylonitrile butadiene styrene(ABS)and high impact polystyrene(HIPS).Besides,the results from rule of mixtures can accurately predict the longitudinal Young’s modulus of the 3D printed specimens,but there exists a large discrepancy for the prediction of the tensile strength.The microstructure analysis shows that the failure modes of 3D printed composites mainly include fiber debonding,fiber pull-out,stress whitening and matrix cracking.展开更多
Basalt Fiber Reinforced Polymer(BFRP)composites have huge potential application respects for some civil fields due to enough strength/modulus to weight and low cost by replacing carbon fiber composites.Aiming at the i...Basalt Fiber Reinforced Polymer(BFRP)composites have huge potential application respects for some civil fields due to enough strength/modulus to weight and low cost by replacing carbon fiber composites.Aiming at the issues in the Resin-Rich Region(RRR)and Interfacial Transition Region(ITR)of fiber reinforced polymer composites,the characteristic Aramid Pulp(AP)fibers with micro-fiber trunk and nano-fiber branches were manufactured into multiple non-woven ultra-thin interleaving at the interlayers of BFRP composites via compression molding to reinforce the flexural strengths and elastic moduli.AP fibers were introduced into RRR to form interleaving at the interlayer,the brittle epoxy adhesive layer was improved and enabled to avoid cracking under a low external load.Free fiber branches of AP were also embedded into BF layer to construct quasi-vertical fiber bridging behaviors in ITR,stronger mechanical interlocking was created to prevent crack propagation along the bonding interface of BF/epoxy.Three-point bending testing results showed the interleaving film with 4 g/m^(2)AP exhibited the best effect among various areal densities and yielded average 315.75 MPa in flexural strength and 21.38 GPa in elastic modulus,having a 63.4%increment and a 47.1%increment respectively compared with the bases.Overall,the simple and low-cost AP interleaving is confirmed as an effective method in improving interlayer structure and flexural performance of BFRP composites,which may be considered to manufacture high-performance laminated fiber reinforced polymer composites in civil aviation industry.展开更多
The woven basalt fiber composites(WBFC) and the unidirectional [0°/90°/45°/-45°]s basalt fiber composites(UBFC) were prepared by hot-pressing.Three-point bending test,low velocity impact test,and b...The woven basalt fiber composites(WBFC) and the unidirectional [0°/90°/45°/-45°]s basalt fiber composites(UBFC) were prepared by hot-pressing.Three-point bending test,low velocity impact test,and ballistic test were performed to the prepared composites.After the tests,the specimens were recovered and analyzed for micromorphology.Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC.Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC,but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC.For the ballistic test,it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests,microscopic analysis of the specimens was applied,and their failure mechanism was discussed.The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage.Although delamination damage can be found in the WBFC under the above loading conditions,the degree of delamination is far less than that of the UBFC.展开更多
In plain mortar,the water film thickness(WFT)has been found to play a key role in the fresh properties.However,in fiber-reinforced mortar,the role of WFT has not been investigated yet.In this research,basalt fibers of...In plain mortar,the water film thickness(WFT)has been found to play a key role in the fresh properties.However,in fiber-reinforced mortar,the role of WFT has not been investigated yet.In this research,basalt fibers of different lengths were added to the mortar,and the dynamic and static flowability,cohesiveness,adhesiveness,and packing density were tested to study the effects of fiber length on the packing density and WFT,and the combined effects of fiber length and WFT on the fresh properties.The results showed that in fiber-reinforced mortar,the WFT also plays a key role,whereas the fiber length exerts its influences through the indirect effects on the packing density and WFT and the direct effect on fiber-mortar interaction.Basically,an increase in fiber length decreases the packing density and WFT,decreases the dynamic and static flowability needed for placing,increases the cohesiveness needed for avoiding segregation,and,quite unexpectedly,decreases the adhesiveness needed for rendering and spraying applications.Regression analysis yielded good correlation of the fresh properties to fiber length and WFT,and best-fit formulas for the mix design for basalt fiber-reinforced mortar were obtained.展开更多
To enhance the sulfate attack resistance performance of concrete,Sulfate erosion test was carried out on basalt fiber concrete with different contents,selecting a concentration of 5%sulfate solution and using a dry−we...To enhance the sulfate attack resistance performance of concrete,Sulfate erosion test was carried out on basalt fiber concrete with different contents,selecting a concentration of 5%sulfate solution and using a dry−wet cycle mechanism attack of basalt fiber-reinforced concrete(BFRC).Every 15 dry−wet cycles,the mass,compressive strength,splitting tensile strength,and relative dynamic elastic modulus of BFRC were tested,and the SO_(4)^(2−)con-centration was measured.This work demonstrates that the mass,relative dynamic elastic modulus,compressive and splitting tensile strength of BFRC reveal a trend of climb up and then decline with the process of the dry−wet cycle.Basalt fiber can enhance the sulfate corrosion resistance of concrete by delaying the erosion of concrete induced by SO_(4)^(2−)and increasing the bearing and anti-deformation capacities of concrete by improving its inter-nal structure.Additionally,when mixing 0.2%basalt fiber into concrete,the strength deterioration rate will be reduced when the peak values of splitting tensile and compressive strength appear at 60 and 75 times the alter-nating dry−wet cycles,respectively.Adverse effects will occur when the fiber volume fraction exceeds 0.2%.The research in this paper can provide a foundation for the engineering applications of basalt fiber concrete.展开更多
Plasma surface modification (Argon: Hydrogen =0.6: 0.4) of basalt fibers was investigated and the element contents of basalt and wood fibers were determined by X-ray energy dispersion spectroscope (EDS). Configuration...Plasma surface modification (Argon: Hydrogen =0.6: 0.4) of basalt fibers was investigated and the element contents of basalt and wood fibers were determined by X-ray energy dispersion spectroscope (EDS). Configuration of basalt fibers was described by means of confocal Laser Raman microRaman spectrometer and Fourier transform infrared spectroscopy. And the morphology of fiber surface was studied with scanning electron microscope (SEM). The modified samples were characterized by X-ray photoelectron spectra (XPS). The results showed that the roughness of basalt fibers was increased with the increase of exposure time of plasma. At the same time the wettability and surface characteristics such as active groups of NH2, OH were improved as well. Basalt fibers were of good chemical stability, better mechanism intension and thermo-stability etc. They mainly consist of 4-, 4-, 2- . Further experiments demostrated that they were degraded into edaphic matrix after use. Therefore, they were environmentally friendly.展开更多
The development of recycled aggregate concrete(RAC)provides a new approach to limiting the waste of natural resources.In the present study,the mechanical properties and deformability of RACs were improved by adding ba...The development of recycled aggregate concrete(RAC)provides a new approach to limiting the waste of natural resources.In the present study,the mechanical properties and deformability of RACs were improved by adding basalt fibers(BFs)and using external restraints,such as a fiber-reinforced polymer(FRP)jacket or a PVC pipe.Samples were tested under axial compression.The results showed that RAC(50%replacement of aggregate)containing 0.2%BFs had the best mechanical properties.Using either BFs or PVC reinforcement had a slight effect on the loadbearing capacity and mode of failure.With different levels of BFs,the compressive strengths of the specimens reinforced with 1-layer and 3-layer basalt fiber reinforced polymer(BFRP)increased by 6.7%–10.5%and 16.5%–23.7%,respectively,and the ultimate strains increased by 48.5%–80.7%and 97.1%–141.1%,respectively.The peak stress of the 3-layer BFRP-PVC increased by 42.2%,and the ultimate strain improved by 131.3%,relative to the control.This reinforcement combined the high tensile strength of BFRP,which improved the post-peak behavior,and PVC,which enhanced the structural durability.In addition,to investigate the influence of the various constraints on compressive behavior,the stress-strain response was analyzed.Based on the analysis of experimental results,a peak stress-strain model and an amended ultimate stress-strain model were proposed.The models were verified as well;the result showed that the predictions from calculations are generally consistent with the experimental data(error within 10%).The results of this study provide a theoretical basis and reference for future applications of fiber-reinforced recycled concrete.展开更多
In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, ...In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, shear-lag, computational model, Nielsen-Chen model and Miwa’s model is used to predict the elastic behaviour of basalt short fiber reinforced with Al alloy composites. The Al/basalt Metal Matrix Composites (MMCs) contain basalt short fiber from 2.5% to 10% in steps of 2.5 wt.% and are fabricated using squeeze infiltration technique. The effects of fiber length and orientation on elastic properties of Al/basalt MMCs are investigated. A comparison between the experimental data and the theoretical data based on physical models is made, and the significance of the findings is discussed. The results show that as short basalt fiber content was increased from 2.5% to 10% by wt.%, an improvement in Young’s modulus of 13.26% has been observed. Optical microscopy was used to examine the general microstructure and fiber distribution in the composite produced. Scanning Electron Microscopy (SEM) was performed on the fractured surface to understand the failure mechanisms.展开更多
文摘This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to examine the deterioration mechanisms caused by freeze-thaw cycles and sulfate erosion. The results show that compressive and tensile strengths increase with basalt fiber dosage. The optimal dosage is 0.2%. With longer exposure to sulfate erosion, both strengths decline significantly. Basalt fibers effectively bridge cracks, control expansion, enhance compactness, and improve concrete performance. Ultra-low-temperature freeze-thaw cycles and sulfate erosion cause rapid crack growth. Sulfate erosion produces crystallization products and expansive substances. These fill cracks, create pressure, and damage the internal structure. Freezing and expansion forces further enlarge voids and cracks. This provides space for expansive substances, worsening concrete deterioration and reducing its performance.
基金supported by the National Natural Science Foundation of China(Nos.U22A20252 and 52173076)the Beijing Natural Science Foundation(Nos.Z240030 and L248023)the Liaoning Province Key Research and Development Project(No.2024JH2/102400046)。
文摘Sizing treatment is a suitable technique to modify the fiber-matrix interfaces without damage of inherent performance of fibers.In this work,sizing agents based on Janus particles(JPs)were utilized to enhance the interface of basalt fiber(BF)/poly(vinyl chloride)(PVC)composites.polystyrene/poly(butyl acrylate)(PS/PBA)@silica JPs were synthesized by seed emulsion polymerization and three different sizing agents were prepared for BF sizing treatment.JPs with organic soft sphere and inorganic hard hemisphere enhanced the interfaces through their amphiphilicity,chemical bonding and mechanical interlock.The mechanical properties of composite with JPs sizing treated BFs performed better when there was one JPs layer modified on the interface.According to the intermitting bonding and gradient modulus theory,JPs patterned interfaces are ideal transition layers between high modulus BF and low modulus PVC.
基金Project(2021YFC2900200)supported by the National Key Research and Development Project of ChinaProject(20230203114SF)supported by the Key Research and Development Project of Jilin Province,China。
文摘Basalt fibers/7075 aluminum matrix composites were studied to meet the demand of aluminum alloy drill pipes for material wear resistance.The composites with different basalt fiber additions were prepared by hot pressed sintering and hot extrusion.The mechanical properties as well as friction and wear properties of the composites were studied by microstructure analysis,tensile experiments,friction and wear experiments.The results showed that basalt fibers were oriented and uniformly distributed and led to local grain refinement in the alloy matrix.The hardness and elongation of the composites were improved.The friction coefficient of the composites increased and then decreased,and the maximum wear depth and wear amount decreased,then increased,then decreased again with the growth of basalt fiber addition.Meanwhile,the inclusion of basalt fibers mitigated the uneven wear of the extruded 7075 aluminum alloy.The value of wear depth difference of 7075-0.2BF was the smallest,and that of 7075-2.0BF was close to it.The maximum wear depth and wear volume the 7075-0.2BF and 7075-2.0BF were also the smallest.The inhibition of uneven wear by basalt fibers enhanced of wear resistance for 7075 aluminum alloy,which has reference significance for improving the performance of aluminum alloy drill pipes.
文摘To discuss the pavement performance of basalt fiber-modified asphalt mixtures,the optimum dosages of asphalt and fibers are studied by the Marshall test and the rutting test.The results demonstrate that the optimum dosages of asphalt and fibers are 4.63% and 0.3%,respectively.Then the pavement performances of basalt（polyester,xylogen）fiber-modified asphalt mixtures are investigated through high temperature stability tests,water stability tests and low temperature crack resistance tests.It indicates that the pavement performances of the fiber-modified asphalt mixtures such as rutting dynamic stability,freezing splitting tensile strength,low temperature crack resistance and so on are improved compared with control asphalt mixture.The results show that the pavement performances of asphalt mixtures can be improved by fiber-modifiers.Besides,the improvement effects of basalt fiber are superior to polyester fiber and xylogen fiber.
基金Fund by Collaborative Innovation Center of Water Conservancy&Transportation Infrastructure Safety,Henan Province,China Postdoctoral Science Fund(No.20110491008)Science and Technology Planning Project of Department of Transportation of Henan Province(No.2013-2-12)The State Key Laboratory Open Fund of Harbor,Coastal and Offshore Engineering(No.LP1113)
文摘The fatigue property of asphalt mixtures under complicated environment （low-temperature bending performance, chloride penetration, freezing-thawing cycle and their coupling effect） and the improvement effect for relevant property of basalt fiber-reinforcing asphalt mixture under complicated environment are studied. Two grading types of asphalt mixtures, AC-16I and AC-13I, are chosen, whose optimum asphalt-aggregate ratio and optimum dosage of basalt fiber are determined by the Marshall test. The standard specimens are made firstly, and then the low temperature bending tests of asphalt mixture and basalt fiber-reinforced asphalt mixture under the coupling effect of the chloride erosion and freezing-thawing cycle have been carried out. Finally, the fatigue property tests of asphalt mixture and basalt fiber-reinforced asphalt mixture under complex environment are performed on MTS material testing system. The results indicate that the tensile strength, the maximum curving tensile stress, the curving stiffness modulus, and fatigue properties of asphalt mixture are influenced by the coupling effect of the chloride erosion and freezing-thawing cycle. The low-temperature bending performance and fatigue property of asphalt mixtures under complicated environment can be greatly improved by adding moderate basalt fiber. The dense gradation asphalt mixture possesses stronger ability to resist adverse environmental effects under the same condition.
基金the National Key Technology Research and Development Program(No.2009BAJ28B02)
文摘This paper discusses a new fibrous composite known as continuous basalt fiber reinforced polymer /plastic(BFRP).Compared with other fiber reinforced polymer/plastic,BFRP has many advantages,such as ductility,high thermal resistance,corrosion resistance and economic cost.To test mechanical properties and failure modes of flexural members strengthened with BFRP,flexural experiment is conducted on four two-span T-section continuous beams strengthened with BFRP and one un-strengthened comparative beam.The experimental result shows that the strengthened beams perform remarkably in terms of yield strength,ultimate strength and ductility.BFRP has good prospects in retrofitting and strengthening of concrete structures which require good ductility and corrosion resistance.
文摘To study the applicability of the basalt fiber through various experimental works in thermal and chemical environments, glass fiber and carbon fiber were compared and discussed. The tensile strength testing was used to investigate the corrosive resistance of basalt fiber, meanwhile, surface study by scanning electron microscopy and microanalysis with complementary X-ray diffraction analysis （SEM/EDS） was also used to ascertain the durability of basalt fiber. The basalt fiber showed better strength retention than the glass fiber at relatively high temperature. Its tensile strength increased when exposed at 300 ~C for several hours, and still maintain about 70% of the initial strength at 400 ~C, whereas that of the glass fiber decreased dramatically. The better stability of the basalt fiber was observed in hydrothermal and chemical environment. The tensile strength of the basalt fiber increased by 20% after the immersion in boiling water and remained well in acid solution, when it comes to glass fiber, the tensile strength decreased to some extent. Although the alkali resistance of basalt fiber was poor at the initial stage, it shows better resistance than the glass fiber after long time treatment.
基金funded by China Postdoctoral Science Foundation(No.2018M643699)the Xi’an Science and Technology Bureau Innovation Leading Projects(No.201805037YD15CG21(23))+2 种基金the Natural Science Foundation of Shaanxi Province(No.2019JQ741)the Science and Technology Bureau of Beilin District,Xi’an(No.GX2035)the Postdoctoral Science Foundation of Shaanxi Province(No.2018BSHEDZZ101)。
文摘A valid strategy to tailor the properties of polylactic acid for more extensive applications was introducing filler.In this work,basalt fiber assembled with in-situ SiO_(2) nanoparticles on the surface was successfully prepared via hydrothermal method and it was further treated with coupling agent KH-550 to improve interfacial interaction between polylactic acid(PLA)and basalt fibers(BF).It was demonstrated that the introduction of BFS could increase the crystallization of PLA and resulted in forming trans-crystallization based on TG and DSC results.The tensile strength of PLA/BF composites raised from 39 MPa to 62.5 MPa with increasing the fiber loading from 1 wt%to 10 wt%.Furthermore,the interfacial interaction could be effectively improved by assembling SiO_(2)(especially with 250 nm in diameter)on BF surface to build mechanical locking,which could keep the PLA matrix in place during the mechanical deformation with the tensile strength value raised from 62.5 MPa to 74.0 MPa.It is noticeable that the impact and flexural properties were effectively increased with the incorporation of in-situ SiO_(2) nanoparticles.The further KH-550 treatment made a positive impact as well.For instance,the impact strength and flexural strength of the sample with SiO_(2) and KH-550 modification were improved to 22.49 k J/m^(2) and 146.83 MPa and it enhanced about 42.16%and 41.04%than those of neat PLA,respectively.Therefore,an efficient enhancement of mechanical performance was achieved and this concept of assembling in-situ SiO_(2) on silica-based fiber as a modifier was a novel and simple path to design the interfacial construction and properties of the polymer composites.
基金Funded by The National Natural Science Foundation of China(No.51108082)
文摘The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and the repeated creep tests. The results show that basalt fiber has excellent reinforced performances, such as high asphalt absorption ratio, low water absorption ratio, high tensile strength, high elastic modulus and high temperature stability. The rutting factor of the fiber reinforced asphalt mastic is higher than the plain asphalt mastic and the reinforced effects are more remarkable under high temperature. The rheological performances of the asphalt mastic demonstrate a good linear relationship between different temperature and loading frequency. The creep stiffness modulus of the asphalt mastic at different loading time can be expressed by power function. Improved Burgers model is used to represent the rheological behaviors of the asphalt mastic with basalt fiber and the model parameters are estimated.
文摘In this investigation, basalt mineral fiber softening agent was prepared in order to obtain desirable flexible performance. Stability and physical chemistry natures of softening agent were evaluated by particle size distribution, dilution, storage and folding endurance etc. Constitutes of basalt and wood fibers were determined by energy dispersion analysis X-ray which served as an accessory of scanning electron microscopy (SEM-EDAX). Naturally degradable ecocomposite was prepared by basalt and wood fibers. The results of SEM observation illustrated that the wood and basalt fibers were blended uniformly. The impact factors of beating degree, content of wood fibers and adhesive etc. were discussed. The structure of the naturally degradable ecocomposite was contrasted with that of pure wood fibers and the cause of excellent filtration performance was analyzed. Compared with traditional methods, it was of saving wood resource, a large amount of water and reducing second pollution. As a consequence, the ecocomposite harmonized with environment and accorded with requirement of benignly friendly environment.
基金the financial support from the National Key Research and Development Program of China(grant no.2020YFA0711800)National Natural Science Foundation of China(grant no.11802027)+2 种基金State Key Laboratory of Explosion Science and Technology(grant no.YPJH20-6,QNKT20-01,JCRC18-01)BITBRFFR Joint Research Program(BITBLR2020018)Beijing Institute of Technology Research Fund。
文摘Continuous basalt fiber(CBF)is an outstanding inorganic fiber produced from nature,which has a wide range of applications in the field of armor protection of national defense military.However,the mechanical response and failure mechanism of 3D printed CBF reinforced components are still not well understood.Here,the 3D printing thermoplastic composites with high volume fraction CBF have been successfully prepared by fused deposition modelling(FDM)method.The effects of fiber printing direction and polymer matrix type on the tensile and flexural properties of the 3D printed composites have been explored,and the detailed failure morphology has been characterized using scanning electron microscopy and optical microscopy.It was found that under high fiber volume fraction,3D printed CBF reinforced polyamides(PA)composites have the best ability to maintain material integrity of the composites,followed by acrylonitrile butadiene styrene(ABS)and high impact polystyrene(HIPS).Besides,the results from rule of mixtures can accurately predict the longitudinal Young’s modulus of the 3D printed specimens,but there exists a large discrepancy for the prediction of the tensile strength.The microstructure analysis shows that the failure modes of 3D printed composites mainly include fiber debonding,fiber pull-out,stress whitening and matrix cracking.
基金supported financially by the National Natural Science Foundations of China(No.52102115)the Overseas High-End Talent Introduction Project of Sichuan Province,China(No.2023JDGD0013)the Natural Science Foundations of Sichuan Province,China(No.2023NSFSC0961)。
文摘Basalt Fiber Reinforced Polymer(BFRP)composites have huge potential application respects for some civil fields due to enough strength/modulus to weight and low cost by replacing carbon fiber composites.Aiming at the issues in the Resin-Rich Region(RRR)and Interfacial Transition Region(ITR)of fiber reinforced polymer composites,the characteristic Aramid Pulp(AP)fibers with micro-fiber trunk and nano-fiber branches were manufactured into multiple non-woven ultra-thin interleaving at the interlayers of BFRP composites via compression molding to reinforce the flexural strengths and elastic moduli.AP fibers were introduced into RRR to form interleaving at the interlayer,the brittle epoxy adhesive layer was improved and enabled to avoid cracking under a low external load.Free fiber branches of AP were also embedded into BF layer to construct quasi-vertical fiber bridging behaviors in ITR,stronger mechanical interlocking was created to prevent crack propagation along the bonding interface of BF/epoxy.Three-point bending testing results showed the interleaving film with 4 g/m^(2)AP exhibited the best effect among various areal densities and yielded average 315.75 MPa in flexural strength and 21.38 GPa in elastic modulus,having a 63.4%increment and a 47.1%increment respectively compared with the bases.Overall,the simple and low-cost AP interleaving is confirmed as an effective method in improving interlayer structure and flexural performance of BFRP composites,which may be considered to manufacture high-performance laminated fiber reinforced polymer composites in civil aviation industry.
基金supported by the National Science Foundation of China(No.51571033)supported in part by the National Natural Science Foundation of China under Grant No.11521062。
文摘The woven basalt fiber composites(WBFC) and the unidirectional [0°/90°/45°/-45°]s basalt fiber composites(UBFC) were prepared by hot-pressing.Three-point bending test,low velocity impact test,and ballistic test were performed to the prepared composites.After the tests,the specimens were recovered and analyzed for micromorphology.Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC.Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC,but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC.For the ballistic test,it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests,microscopic analysis of the specimens was applied,and their failure mechanism was discussed.The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage.Although delamination damage can be found in the WBFC under the above loading conditions,the degree of delamination is far less than that of the UBFC.
基金Project supported by the National Natural Science Foundation of China(Nos.51608131 and 51808134)the European Regional Development Fund(No.01.2.2-LMT-K-718-03-0010)under grant agreement with the Research Council of Lithuania(LMTLT)+3 种基金the Marie Skłodowska-Curie Actions of the European Commission(No.751461)the Colleges Innovation Project of Guangdong Province(No.2017KTSCX061)the Pearl River S&T Nova Program of Guangzhou City(No.201906010064)the Natural Science Foundation of Guangdong Province(No.2021A1515011747),China。
文摘In plain mortar,the water film thickness(WFT)has been found to play a key role in the fresh properties.However,in fiber-reinforced mortar,the role of WFT has not been investigated yet.In this research,basalt fibers of different lengths were added to the mortar,and the dynamic and static flowability,cohesiveness,adhesiveness,and packing density were tested to study the effects of fiber length on the packing density and WFT,and the combined effects of fiber length and WFT on the fresh properties.The results showed that in fiber-reinforced mortar,the WFT also plays a key role,whereas the fiber length exerts its influences through the indirect effects on the packing density and WFT and the direct effect on fiber-mortar interaction.Basically,an increase in fiber length decreases the packing density and WFT,decreases the dynamic and static flowability needed for placing,increases the cohesiveness needed for avoiding segregation,and,quite unexpectedly,decreases the adhesiveness needed for rendering and spraying applications.Regression analysis yielded good correlation of the fresh properties to fiber length and WFT,and best-fit formulas for the mix design for basalt fiber-reinforced mortar were obtained.
基金supports for the study were provided by the Natural Sciences Foundation Committee of China(Grant No.41472254,Jinming Xu,http://www.nsfc.gov.cn)。
文摘To enhance the sulfate attack resistance performance of concrete,Sulfate erosion test was carried out on basalt fiber concrete with different contents,selecting a concentration of 5%sulfate solution and using a dry−wet cycle mechanism attack of basalt fiber-reinforced concrete(BFRC).Every 15 dry−wet cycles,the mass,compressive strength,splitting tensile strength,and relative dynamic elastic modulus of BFRC were tested,and the SO_(4)^(2−)con-centration was measured.This work demonstrates that the mass,relative dynamic elastic modulus,compressive and splitting tensile strength of BFRC reveal a trend of climb up and then decline with the process of the dry−wet cycle.Basalt fiber can enhance the sulfate corrosion resistance of concrete by delaying the erosion of concrete induced by SO_(4)^(2−)and increasing the bearing and anti-deformation capacities of concrete by improving its inter-nal structure.Additionally,when mixing 0.2%basalt fiber into concrete,the strength deterioration rate will be reduced when the peak values of splitting tensile and compressive strength appear at 60 and 75 times the alter-nating dry−wet cycles,respectively.Adverse effects will occur when the fiber volume fraction exceeds 0.2%.The research in this paper can provide a foundation for the engineering applications of basalt fiber concrete.
文摘Plasma surface modification (Argon: Hydrogen =0.6: 0.4) of basalt fibers was investigated and the element contents of basalt and wood fibers were determined by X-ray energy dispersion spectroscope (EDS). Configuration of basalt fibers was described by means of confocal Laser Raman microRaman spectrometer and Fourier transform infrared spectroscopy. And the morphology of fiber surface was studied with scanning electron microscope (SEM). The modified samples were characterized by X-ray photoelectron spectra (XPS). The results showed that the roughness of basalt fibers was increased with the increase of exposure time of plasma. At the same time the wettability and surface characteristics such as active groups of NH2, OH were improved as well. Basalt fibers were of good chemical stability, better mechanism intension and thermo-stability etc. They mainly consist of 4-, 4-, 2- . Further experiments demostrated that they were degraded into edaphic matrix after use. Therefore, they were environmentally friendly.
基金supported by the Natural Science Foundation Project of Liaoning Provincial Department of Education of China under Grant No.JJL201915404,Zhejiang Provincial Natural Science Foundation of China under Grant No.LQ22E080024 and Zhejiang Province Department of Education Fund of China under Grant No.Y202146776.
文摘The development of recycled aggregate concrete(RAC)provides a new approach to limiting the waste of natural resources.In the present study,the mechanical properties and deformability of RACs were improved by adding basalt fibers(BFs)and using external restraints,such as a fiber-reinforced polymer(FRP)jacket or a PVC pipe.Samples were tested under axial compression.The results showed that RAC(50%replacement of aggregate)containing 0.2%BFs had the best mechanical properties.Using either BFs or PVC reinforcement had a slight effect on the loadbearing capacity and mode of failure.With different levels of BFs,the compressive strengths of the specimens reinforced with 1-layer and 3-layer basalt fiber reinforced polymer(BFRP)increased by 6.7%–10.5%and 16.5%–23.7%,respectively,and the ultimate strains increased by 48.5%–80.7%and 97.1%–141.1%,respectively.The peak stress of the 3-layer BFRP-PVC increased by 42.2%,and the ultimate strain improved by 131.3%,relative to the control.This reinforcement combined the high tensile strength of BFRP,which improved the post-peak behavior,and PVC,which enhanced the structural durability.In addition,to investigate the influence of the various constraints on compressive behavior,the stress-strain response was analyzed.Based on the analysis of experimental results,a peak stress-strain model and an amended ultimate stress-strain model were proposed.The models were verified as well;the result showed that the predictions from calculations are generally consistent with the experimental data(error within 10%).The results of this study provide a theoretical basis and reference for future applications of fiber-reinforced recycled concrete.
文摘In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, shear-lag, computational model, Nielsen-Chen model and Miwa’s model is used to predict the elastic behaviour of basalt short fiber reinforced with Al alloy composites. The Al/basalt Metal Matrix Composites (MMCs) contain basalt short fiber from 2.5% to 10% in steps of 2.5 wt.% and are fabricated using squeeze infiltration technique. The effects of fiber length and orientation on elastic properties of Al/basalt MMCs are investigated. A comparison between the experimental data and the theoretical data based on physical models is made, and the significance of the findings is discussed. The results show that as short basalt fiber content was increased from 2.5% to 10% by wt.%, an improvement in Young’s modulus of 13.26% has been observed. Optical microscopy was used to examine the general microstructure and fiber distribution in the composite produced. Scanning Electron Microscopy (SEM) was performed on the fractured surface to understand the failure mechanisms.
