In data stream management systems (DSMSs), how to maintain the quality of queries is a difficult problem because both the processing cost and data arrival rates are highly unpredictable. When the system is overloaded,...In data stream management systems (DSMSs), how to maintain the quality of queries is a difficult problem because both the processing cost and data arrival rates are highly unpredictable. When the system is overloaded, quality degrades significantly and thus load shedding becomes necessary. Unlike processing overloading in the general way which is only by a feedback control (FB) loop to obtain a good and stable performance over data streams, a feedback plus feed-forward control (FFC) strategy is introduced in DSMSs, which have a good quality of service (QoS) in the aspects of miss ratio and processing delay. In this paper, a quality adaptation framework is proposed, in which the control-theory-based techniques are leveraged to adjust the application behavior with the considerations of the current system status. Compared to previous solutions, the FFC strategy achieves a good quality with a waste of fewer resources.展开更多
The coagulation bath system of carbon fiber precursor is a complicated and multivariable coupling system. Based on the model of industrial production,the full dynamic decoupling control of the coagulation bath system ...The coagulation bath system of carbon fiber precursor is a complicated and multivariable coupling system. Based on the model of industrial production,the full dynamic decoupling control of the coagulation bath system of carbon fiber precursor is achieved in combination with multivariable feed-forward-like decoupling and proportional-integral-differential( PID) control. Compared with the conventional PID decoupling control,the experiment results show that the proposed method has a better control effect. The use of the controller can achieve complete decoupling of three parameters from coagulation bath system. The method should have great applications.展开更多
This paper presents a simple and robust speed control scheme of Permanent Magnet Synchronous Motor (PMSM). It is to achieve accurate control performance in the presence of load torque and plant parameter variation. A ...This paper presents a simple and robust speed control scheme of Permanent Magnet Synchronous Motor (PMSM). It is to achieve accurate control performance in the presence of load torque and plant parameter variation. A robust disturbance cancellation feed forward controller is used to estimate the torque disturbance. The simple and practical control scheme is easily implemented on a PMSM driver using a TMS320LF2407 DSP. The effectiveness of the proposed robust speed control approach is demonstrated by simulation and experimental results.展开更多
The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow r...The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow rate of external carbon dosage to the anoxic zone, thus the concentration of nitrate plus nitrite(NOx--N) in the anoxic zone was kept closed to the set point. The relationship was studied between the NOx--N concentration in the anoxic zone(S_ NO) and the dosage of external carbon, and the results showed that the removal efficiency of the total nitrogen(TN) could not be largely improved by double dosage of carbon source when S_ NO reached about 2 mg/L. Through keeping S_ NO at the level of about 2 mg/L, the demand of effluent quality could be met and the carbon dosage could be optimized. Based on the Activated Sludge Model No.1(ASM No.1), a simplified mathematical model of external carbon dosage was developed. Simulation results showed that PI controller and feed-forward PI controller both had good dynamic response and steady precision. And feed-forward PI controller had better control effects due to its consideration of influent disturbances.展开更多
Advanced driver assistance systems(ADAS) seek to provide drivers and passengers of automotive vehicles increased safety and comfort. Original equipment manufacturers are integrating and developing systems for distance...Advanced driver assistance systems(ADAS) seek to provide drivers and passengers of automotive vehicles increased safety and comfort. Original equipment manufacturers are integrating and developing systems for distance keeping, lane keeping and changing and other functionalities. The modern automobile is a complex system of systems. How the functionalities of advanced driver assistance are implemented and coordinated across the systems of the vehicle is generally not made available to the wider research community by the developers and manufactures. This paper seeks to begin filling this gap by assembling open source physics models of the vehicle dynamics and ADAS command models. Additionally, in order to facilitate ADAS development and testing without having access to the details of ADAS, a coordinated control architecture for motion management is also proposed for distributing ADAS motion control commands over vehicle systems. The architecture is demonstrated in a case study where motion is coordinated between the steering and the braking systems, which are typically used only for a single functionality. The integrated vehicle and system dynamics using the coordinated control architecture are simulated for various driving tasks. It is seen that improved trajectory following can be achieved by the proposed coordinated control architecture. The models, simulations and control architecture are made available for open access.展开更多
Not so much had been talked about equilibrium in control area. On the basis of the phenomenon of balance, the concept of control-equilibrium and control-equilibrium of a control system is proposed. According to this t...Not so much had been talked about equilibrium in control area. On the basis of the phenomenon of balance, the concept of control-equilibrium and control-equilibrium of a control system is proposed. According to this theory, a perfect control method should not only guarantee stability of the system, but also ensure the control-equilibrium of the system. To achieve the control-equilibrium, feed-forward control is required.展开更多
This paper is concerned with the control design and the theoretical analysis for a class of input time-delay systems with stable, critical stable or unstable poles. In order to overcome the time delay, a novel feed-fo...This paper is concerned with the control design and the theoretical analysis for a class of input time-delay systems with stable, critical stable or unstable poles. In order to overcome the time delay, a novel feed-forward compensation active disturbance rejection control(FFC-ADRC) approach is proposed. It combines advantages of the Smith predictor and the traditional active disturbance rejection control(ADRC). The tracking differentiator(TD) is designed to predict the control signal, which adds an anticipatory control to the control signal and allows a higher observer bandwidth to obtain better disturbance rejection. The modified extended state observer(ESO) is designed to estimate both system states and the total disturbances(internal disturbance, uncertainties and delayed disturbance). Then the Lyapunov theory and the theory of the input-output stability are applied to prove the asymptotic stability of the closed-loop control system. Finally, numerical simulations show the effectiveness and practicality of the proposed design.展开更多
The paper presents a successful design and good result of grid voltage feed-forward control strategy with no damping regulator of LCL filter applied in Three-phase Pulse Width Modulation( PWM) rectifier under unbalanc...The paper presents a successful design and good result of grid voltage feed-forward control strategy with no damping regulator of LCL filter applied in Three-phase Pulse Width Modulation( PWM) rectifier under unbalance grid condition for renewable energy processing. It is demonstrated that the closed-loop current control is decoupled with the grid voltage feed-forward control,and good waveform of grid current with low order harmonics is obtained under unbalance grid condition. This novel strategy is simple and reliable,applied with PI regulator but no resonant controller in α,β two-phase stationary frame. Moreover,the results of experiment and simulation are also illustrated to validate the novel strategy well applied in the closed-loop current control system under unbalanced grid condition.展开更多
To satisfy the requirements of motion control for industrial machine, a multi-axis motion controller based on DSP is developed in this paper. The motion controller consists of DSP which plays a main role in this desig...To satisfy the requirements of motion control for industrial machine, a multi-axis motion controller based on DSP is developed in this paper. The motion controller consists of DSP which plays a main role in this design;DPRAM to make sure the rapid and reliable communication with host;FPGA to handle the task of address decoder and receiving feed-back encoder signal;and several peripheral logic circuits. In the part of hardware design, overall structure of motion control system is presented. Then, the Feed-Forward Proportional-Integral-Velocity (FFPIV) scheme which introduces KV in term of velocity loop to achieve the accurate, smooth and real-time response is proposed in the software developing part. The experiment data are carried out to indicate that this motion controller has advantages of superior performance and highly machining precision.展开更多
Greenhouse system (GHS) is the worldwide fastest growing phenomenon in agricultural sector. Greenhouse models are essential for improving control efficiencies. The Relative Gain Analysis (RGA) reveals that the GHS con...Greenhouse system (GHS) is the worldwide fastest growing phenomenon in agricultural sector. Greenhouse models are essential for improving control efficiencies. The Relative Gain Analysis (RGA) reveals that the GHS control is complex due to 1) high nonlinear interactions between the biological subsystem and the physical subsystem and 2) strong coupling between the process variables such as temperature and humidity. In this paper, a decoupled linear cooling model has been developed using a feedback-feed forward linearization technique. Further, based on the model developed Internal Model Control (IMC) based Proportional Integrator (PI) controller parameters are optimized using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO) to achieve minimum Integral Square Error (ISE). The closed loop control is carried out using the above control schemes for set-point change and disturbance rejection. Finally, closed loop servo and servo-regulatory responses of GHS are compared quantitatively as well as qualitatively. The results implicate that IMC based PI controller using PSO provides better performance than the IMC based PI controller using GA. Also, it is observed that the disturbance introduced in one loop will not affect the other loop due to feedback-feed forward linearization and decoupling. Such a control scheme used for GHS would result in better yield in production of crops such as tomato, lettuce and broccoli.展开更多
The stable operation of the central air conditioning water system always is a major difficulty for the control profession. Paper focus on the water system with multi variable, strong coupling, nonlinear, large time de...The stable operation of the central air conditioning water system always is a major difficulty for the control profession. Paper focus on the water system with multi variable, strong coupling, nonlinear, large time delay characteristics, presented use feed forward coupling compensation method, to eliminate the coupling effect between temperature and pressure. In this paper, the Elman neural network controller is designed for the first time, and the simulation results show that the response time of Elman neural network controller is shorter, the system is more stable and the overshoot is small.展开更多
A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the prec...A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the precision of CD pipelined ADCs is restricted by the variation in input CM charge, which can compensate for CM charge errors caused by a variation in CM charge input in real time. Based on the feed-forward CM charge control circuit, a 12-bit 250-MS/s CD pipelined ADC is designed and realized using a 1P6M 0.18-μm CMOS process. The ADC achieved a Spurious Free Dynamic Range （SFDR） of 78.1 dB and a Signal-to-Noise-and-Distortion Ratio （SNDR） of 64.6 dB for a 20.1-MHz input; a SFDR of 74.9 dB and SNDR of 62.0 dB were achieved for a 239.9-MHz input at full sampling rate. The variation in signal-to-noise ratio was less than 3 dB over a 0-1.2 V input CM voltage range. The power consumption of the prototype ADC is only 85 mW at 1.8 V supply, and it occupies an active die area of 2.24 mm^2.展开更多
基金Supported by the National Key R&D Program of China(2016YFC1401900)the National Science Foundation of China(61173029,61672144)
文摘In data stream management systems (DSMSs), how to maintain the quality of queries is a difficult problem because both the processing cost and data arrival rates are highly unpredictable. When the system is overloaded, quality degrades significantly and thus load shedding becomes necessary. Unlike processing overloading in the general way which is only by a feedback control (FB) loop to obtain a good and stable performance over data streams, a feedback plus feed-forward control (FFC) strategy is introduced in DSMSs, which have a good quality of service (QoS) in the aspects of miss ratio and processing delay. In this paper, a quality adaptation framework is proposed, in which the control-theory-based techniques are leveraged to adjust the application behavior with the considerations of the current system status. Compared to previous solutions, the FFC strategy achieves a good quality with a waste of fewer resources.
基金the Key Project of the National Nature Science Foundation of China(No.61134009)Program for Changjiang Scholars and Innovation Research Team in University from the Ministry of Education,China(No.IRT1220)+1 种基金Specialized Research Fund for Shanghai Leading Talents,Project of the Shanghai Committee of Science and Technology,China(No.13JC1407500)the Fundamental Research Funds for the Central Universities,China(No.2232012A3-04)
文摘The coagulation bath system of carbon fiber precursor is a complicated and multivariable coupling system. Based on the model of industrial production,the full dynamic decoupling control of the coagulation bath system of carbon fiber precursor is achieved in combination with multivariable feed-forward-like decoupling and proportional-integral-differential( PID) control. Compared with the conventional PID decoupling control,the experiment results show that the proposed method has a better control effect. The use of the controller can achieve complete decoupling of three parameters from coagulation bath system. The method should have great applications.
基金This work was supported High-Tech Research and Development Program of China (No. 2001AA423160)
文摘This paper presents a simple and robust speed control scheme of Permanent Magnet Synchronous Motor (PMSM). It is to achieve accurate control performance in the presence of load torque and plant parameter variation. A robust disturbance cancellation feed forward controller is used to estimate the torque disturbance. The simple and practical control scheme is easily implemented on a PMSM driver using a TMS320LF2407 DSP. The effectiveness of the proposed robust speed control approach is demonstrated by simulation and experimental results.
基金Foundation item:Beijing Science and Technology Commission(No. H020620010120), the Significant International Projects of the National Natural Science Foundation of China(No. 50521140075), Beijing Municipal Education Commission(No. KZ200310005003) and Beijing Key Laboratories
文摘The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow rate of external carbon dosage to the anoxic zone, thus the concentration of nitrate plus nitrite(NOx--N) in the anoxic zone was kept closed to the set point. The relationship was studied between the NOx--N concentration in the anoxic zone(S_ NO) and the dosage of external carbon, and the results showed that the removal efficiency of the total nitrogen(TN) could not be largely improved by double dosage of carbon source when S_ NO reached about 2 mg/L. Through keeping S_ NO at the level of about 2 mg/L, the demand of effluent quality could be met and the carbon dosage could be optimized. Based on the Activated Sludge Model No.1(ASM No.1), a simplified mathematical model of external carbon dosage was developed. Simulation results showed that PI controller and feed-forward PI controller both had good dynamic response and steady precision. And feed-forward PI controller had better control effects due to its consideration of influent disturbances.
基金supported by the Programme for Simulation Innovation(PSI)
文摘Advanced driver assistance systems(ADAS) seek to provide drivers and passengers of automotive vehicles increased safety and comfort. Original equipment manufacturers are integrating and developing systems for distance keeping, lane keeping and changing and other functionalities. The modern automobile is a complex system of systems. How the functionalities of advanced driver assistance are implemented and coordinated across the systems of the vehicle is generally not made available to the wider research community by the developers and manufactures. This paper seeks to begin filling this gap by assembling open source physics models of the vehicle dynamics and ADAS command models. Additionally, in order to facilitate ADAS development and testing without having access to the details of ADAS, a coordinated control architecture for motion management is also proposed for distributing ADAS motion control commands over vehicle systems. The architecture is demonstrated in a case study where motion is coordinated between the steering and the braking systems, which are typically used only for a single functionality. The integrated vehicle and system dynamics using the coordinated control architecture are simulated for various driving tasks. It is seen that improved trajectory following can be achieved by the proposed coordinated control architecture. The models, simulations and control architecture are made available for open access.
文摘Not so much had been talked about equilibrium in control area. On the basis of the phenomenon of balance, the concept of control-equilibrium and control-equilibrium of a control system is proposed. According to this theory, a perfect control method should not only guarantee stability of the system, but also ensure the control-equilibrium of the system. To achieve the control-equilibrium, feed-forward control is required.
基金supported by the National Natural Science Foundation of China(61304026)
文摘This paper is concerned with the control design and the theoretical analysis for a class of input time-delay systems with stable, critical stable or unstable poles. In order to overcome the time delay, a novel feed-forward compensation active disturbance rejection control(FFC-ADRC) approach is proposed. It combines advantages of the Smith predictor and the traditional active disturbance rejection control(ADRC). The tracking differentiator(TD) is designed to predict the control signal, which adds an anticipatory control to the control signal and allows a higher observer bandwidth to obtain better disturbance rejection. The modified extended state observer(ESO) is designed to estimate both system states and the total disturbances(internal disturbance, uncertainties and delayed disturbance). Then the Lyapunov theory and the theory of the input-output stability are applied to prove the asymptotic stability of the closed-loop control system. Finally, numerical simulations show the effectiveness and practicality of the proposed design.
文摘The paper presents a successful design and good result of grid voltage feed-forward control strategy with no damping regulator of LCL filter applied in Three-phase Pulse Width Modulation( PWM) rectifier under unbalance grid condition for renewable energy processing. It is demonstrated that the closed-loop current control is decoupled with the grid voltage feed-forward control,and good waveform of grid current with low order harmonics is obtained under unbalance grid condition. This novel strategy is simple and reliable,applied with PI regulator but no resonant controller in α,β two-phase stationary frame. Moreover,the results of experiment and simulation are also illustrated to validate the novel strategy well applied in the closed-loop current control system under unbalanced grid condition.
文摘To satisfy the requirements of motion control for industrial machine, a multi-axis motion controller based on DSP is developed in this paper. The motion controller consists of DSP which plays a main role in this design;DPRAM to make sure the rapid and reliable communication with host;FPGA to handle the task of address decoder and receiving feed-back encoder signal;and several peripheral logic circuits. In the part of hardware design, overall structure of motion control system is presented. Then, the Feed-Forward Proportional-Integral-Velocity (FFPIV) scheme which introduces KV in term of velocity loop to achieve the accurate, smooth and real-time response is proposed in the software developing part. The experiment data are carried out to indicate that this motion controller has advantages of superior performance and highly machining precision.
文摘Greenhouse system (GHS) is the worldwide fastest growing phenomenon in agricultural sector. Greenhouse models are essential for improving control efficiencies. The Relative Gain Analysis (RGA) reveals that the GHS control is complex due to 1) high nonlinear interactions between the biological subsystem and the physical subsystem and 2) strong coupling between the process variables such as temperature and humidity. In this paper, a decoupled linear cooling model has been developed using a feedback-feed forward linearization technique. Further, based on the model developed Internal Model Control (IMC) based Proportional Integrator (PI) controller parameters are optimized using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO) to achieve minimum Integral Square Error (ISE). The closed loop control is carried out using the above control schemes for set-point change and disturbance rejection. Finally, closed loop servo and servo-regulatory responses of GHS are compared quantitatively as well as qualitatively. The results implicate that IMC based PI controller using PSO provides better performance than the IMC based PI controller using GA. Also, it is observed that the disturbance introduced in one loop will not affect the other loop due to feedback-feed forward linearization and decoupling. Such a control scheme used for GHS would result in better yield in production of crops such as tomato, lettuce and broccoli.
文摘The stable operation of the central air conditioning water system always is a major difficulty for the control profession. Paper focus on the water system with multi variable, strong coupling, nonlinear, large time delay characteristics, presented use feed forward coupling compensation method, to eliminate the coupling effect between temperature and pressure. In this paper, the Elman neural network controller is designed for the first time, and the simulation results show that the response time of Elman neural network controller is shorter, the system is more stable and the overshoot is small.
基金supported by National Natural Science Foundation of China under grant No.61704161Key Project of Natural Science of Anhui Provincial Department of Education under grant No.KJ2017A396
文摘A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the precision of CD pipelined ADCs is restricted by the variation in input CM charge, which can compensate for CM charge errors caused by a variation in CM charge input in real time. Based on the feed-forward CM charge control circuit, a 12-bit 250-MS/s CD pipelined ADC is designed and realized using a 1P6M 0.18-μm CMOS process. The ADC achieved a Spurious Free Dynamic Range （SFDR） of 78.1 dB and a Signal-to-Noise-and-Distortion Ratio （SNDR） of 64.6 dB for a 20.1-MHz input; a SFDR of 74.9 dB and SNDR of 62.0 dB were achieved for a 239.9-MHz input at full sampling rate. The variation in signal-to-noise ratio was less than 3 dB over a 0-1.2 V input CM voltage range. The power consumption of the prototype ADC is only 85 mW at 1.8 V supply, and it occupies an active die area of 2.24 mm^2.
