We propose a theoretical model to describe external-cavity distributed feedback semiconductor lasers and investigate the impact of the number of external feedback points on linewidth and side-mode suppression ratio th...We propose a theoretical model to describe external-cavity distributed feedback semiconductor lasers and investigate the impact of the number of external feedback points on linewidth and side-mode suppression ratio through numerical simulation. The simulation results demonstrate that the linewidth of external-cavity semiconductor lasers can be reduced by increasing the external cavity length and feedback ratio, and adding more external feedback points can further narrow the linewidth and enhance the side mode suppression ratio. This research provides insight into the external cavity distributed feedback mechanism and can guide the design of high-performance external cavity semiconductor lasers. .展开更多
A novel scheme for generating optical chaos is proposed and experimentally demonstrated,which supports to simultaneously produce two low-correlation chaotic signals with wideband spectrum and suppressed time-delay-sig...A novel scheme for generating optical chaos is proposed and experimentally demonstrated,which supports to simultaneously produce two low-correlation chaotic signals with wideband spectrum and suppressed time-delay-signature(TDS).In the proposed scheme,we use the output of an external-cavity semiconductor laser(ECSL)as the driving signal of a phase modulator to modulate the output of a CW laser.Then the phase-modulated continuous-wave(CW)light is split into two parts,one is injected back into the ECSL that outputs one chaotic signal,while the other part is passed through a dispersion module for generating another chaotic signal simultaneously.The experimental results prove that the proposed scheme has three merits.Firstly,it can improve the bandwidth of ECSL-based chaos by several times,and simultaneously generate another wideband flat-spectrum chaotic signal.Secondly,the undesired TDS characteristics of the simultaneously-generated chaotic signals can be efficiently suppressed to an indistinguishable level within a wide parameter range,as such the complexities of the chaotic signals are considerably high.Thirdly,the correlation coefficient between these two simultaneously-generated chaotic signals is smaller than 0.1.The proposed scheme provides an attractive solution for parallel multiple chaos generation,and shows great potential for multiple channel chaos communications and multiple random bit generations.展开更多
We demonstrate high-performance broadband tunable external-cavity lasers(ECLs) with the metal-organic chemical vapor deposition(MOCVD) grown In As/In P quantum dots(QDs) structures. Without cavity facet coatings, the ...We demonstrate high-performance broadband tunable external-cavity lasers(ECLs) with the metal-organic chemical vapor deposition(MOCVD) grown In As/In P quantum dots(QDs) structures. Without cavity facet coatings, the 3-d B spectral bandwidth of the Fabry–Perot(FP) laser is approximately 10.8 nm, while the tuning bandwidth of ECLs is 45 nm.Combined with the anti-reflection(AR)/high-reflection(HR) facet coating, a 92 nm bandwidth tuning range has been obtained with the wavelength covering from 1414 nm to 1506 nm. In most of the tuning range, the threshold current density is lower than 1.5 k A/cm2. The maximum output power of 6.5 m W was achieved under a 500 m A injection current.All achievements mentioned above were obtained under continuous-wave(CW) mode at room temperature(RT).展开更多
External-cavity birefringence feedback effects of the microchip Nd：YAG laser are presented. When a birefringence element is placed in the external feedback cavity of the laser, two orthogonally polarized laser beams ...External-cavity birefringence feedback effects of the microchip Nd：YAG laser are presented. When a birefringence element is placed in the external feedback cavity of the laser, two orthogonally polarized laser beams with a phase difference are output. The phase difference is twice as large as the phase retardation in the external cavity along the two orthogonal directions. The variable extra-cavity birefringence, caused by rotation of the external-cavity birefringenee element, results in tunable phase difference between the two orthogonally polarized beams. This means that the roll angle information has been translated to phase difference of two output laser beams. A theoretical analysis based on the Fabry-Perot cavity equivalent model and refractive index ellipsoid is presented, which is in good agreement with the experimental results. This phenomenon has potential applications for roll angle measurement.展开更多
We report an external cavity quantum cascade laser （EC-QCL） operating near 6.9μm using the Littman Metcalf configuration. The EC-QCL works in a pulsed mode and can be tuned continuously from 1340 to 1640cm^-1 by on...We report an external cavity quantum cascade laser （EC-QCL） operating near 6.9μm using the Littman Metcalf configuration. The EC-QCL works in a pulsed mode and can be tuned continuously from 1340 to 1640cm^-1 by only tilting the tuning mirror. The fine tuning ability of the EC-QCL is demonstrated by measuring the absorption spectrum of water in the ambient air with a lock-in amplifier.展开更多
High power optically pumped vertical-external-cavity surface-emitting lasers with front and end pump are re-ported.The gain chip consists of 15 repeats of In0.26GaAs/GaAsP0.02 multiple quantum wells and 30 pairs of Al...High power optically pumped vertical-external-cavity surface-emitting lasers with front and end pump are re-ported.The gain chip consists of 15 repeats of In0.26GaAs/GaAsP0.02 multiple quantum wells and 30 pairs of Alo.2GaAs/Alo.98GaAs distributed Bragg reflectors.The maximum output power of 3 W,optical-to-optical conversion efficiency of 22.4%,and slope efficiency of 29.8%are obtained with 5-℃heatsink temperature under the front pump,while the maximum output power of 1.1 W,optical-to-optical conversion efficiency of 23.2%,and slope efficiency of 30.8%are reached with 5-℃heatsink temperature under the end pump.Influences of thermal effects on the output power of the laser with front and end pump are discussed.展开更多
By using an external-cavity frequency-doubling master oscillator fiber power amplifier （MOPA）, a 700 mW continuous-wave single-frequency laser source at 780 nm is produced. It is shown that the frequency doubling ef...By using an external-cavity frequency-doubling master oscillator fiber power amplifier （MOPA）, a 700 mW continuous-wave single-frequency laser source at 780 nm is produced. It is shown that the frequency doubling efficiency is improved when the seed diode laser is optically locked to a resonant frequency of a confocal Fabry-Perot （F-P） cavity. This phenomenon can be attributed to the narrowing of the 1.56 μm laser linewidth and explained by our presented theoretical model. The experimental results are found to be in good agreement with the theoretical predictions.展开更多
The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution an...The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution and short wavelength.Efficient and compact 193 nm DUV laser source thus becomes a hot research area.Currently,193 nm Ar F excimer gas laser is widely employed in DUV lithography systems and serves as the enabling technology for 7 and 5 nm semiconductor fabrication.展开更多
Influence produced by the heat effect at work of the laser instrument crystal of the semiconductor, the text designs a kind of temperature control system to the crystal of the laser instrument, using the thought and m...Influence produced by the heat effect at work of the laser instrument crystal of the semiconductor, the text designs a kind of temperature control system to the crystal of the laser instrument, using the thought and method of the classical control theory to analyze this temperature control system, and establishes mathematics model. According to mathematics model the text demonstrated the system at S field and time- area, and proposed optimizing basis to the total mark of proportion and differential parameter to con- troller PID, thus proposed a kind of temperature control scheme. And the thermostatically system is simulated by MATLAB.展开更多
A fitting process is used to measure the cavity loss and the quasi Fermi level separation for Fabry Pérot semiconductor lasers.From the amplified spontaneous emission (ASE) spectrum,the gain spectrum and sing...A fitting process is used to measure the cavity loss and the quasi Fermi level separation for Fabry Pérot semiconductor lasers.From the amplified spontaneous emission (ASE) spectrum,the gain spectrum and single pass ASE obtained by the Cassidy method are applied in the fitting process.For a 1550nm quantum well InGaAsP ridge waveguide laser,the cavity loss of about ～24cm -1 is obtained.展开更多
Internal loss is a key internal parameter for high power 1060-nm InGaAs/A1GaAs semiconductor laser. In this paper, we discuss the origin of internal loss of 1060-nm InGaAs/GaAs quantum welt （QW） AIGaAs separate conf...Internal loss is a key internal parameter for high power 1060-nm InGaAs/A1GaAs semiconductor laser. In this paper, we discuss the origin of internal loss of 1060-nm InGaAs/GaAs quantum welt （QW） AIGaAs separate confinement het- erostructure semiconductor laser, and the method to reduce internal loss. By light doping the n-cladding layer, and stepwise doping the p-cladding layer combined with the expanded waveguide layer, a broad area laser with internal loss of 1/cm is designed and fabricated. Ridge waveguide laser with an output power of 350 mW is obtained. The threshold current and slope efficiency near the threshold current are 20 mA and 0.8 W/A, respectively.展开更多
We solve the single mode coupled rate equations by computer,simulate the behavior of a gain switch of an AlGaInP red light semiconductor laser diode,and find the characteristic of FWHM of pulses changing with the ampl...We solve the single mode coupled rate equations by computer,simulate the behavior of a gain switch of an AlGaInP red light semiconductor laser diode,and find the characteristic of FWHM of pulses changing with the amplitude of modulation signal, the bias current, and the modulated frequency. On this basis, we conduct experiments. The experiment results accord with the simulations well.展开更多
Based on a semiconductor laser （SL） with incoherent optical feedback, a novel all-optical scheme for generating tunable and broadband microwave frequency combs （MFCs） is proposed and investigated numerically. The ...Based on a semiconductor laser （SL） with incoherent optical feedback, a novel all-optical scheme for generating tunable and broadband microwave frequency combs （MFCs） is proposed and investigated numerically. The results show that, under suitable operation parameters, the SL with incoherent optical feedback can be driven to operate at a regular pulsing state, and the generated MFCs have bandwidths broader than 40 GHz within a 10 dB amplitude variation. For a fixed bias current, the line spacing （or repetition frequency） of the MFCs can be easily tuned by varying the feedback delay time and the feedback strength, and the tuning range of the line spacing increases with the increase in the bias current. The linewidth of the MFCs is sensitive to the variation of the feedback delay time and the feedback strength, and a linewidth of tens of KHz can be achieved through finely adjusting the feedback delay time and the feedback strength. In addition, mappings of amplitude variation, repetition frequency, and linewidth of MFCs in the parameter space of the feedback delay time and the feedback strength are presented.展开更多
We introduce a new method of simultaneously implementing frequency stabilization and frequency shift for semiconductor lasers. We name this method the frequency tunable modulation transfer spectroscopy （FTMTS）. To r...We introduce a new method of simultaneously implementing frequency stabilization and frequency shift for semiconductor lasers. We name this method the frequency tunable modulation transfer spectroscopy （FTMTS）. To realize a stable output of 780 nm semiconductor laser, an FTMTS optical heterodyne frequency stabilization system is constructed. Before entering into the frequency stabilization system, the probe laser passes through an acousto-optical modulator （AOM） twice in advance to achieve tunable frequency while keeping the light path stable. According to the experimental results, the frequency changes from 120 MHz to 190 MHz after the double-pass AOM, and the intensity of laser entering into the system is greatly changed, but there is almost no change in the error signal of the FTMTS spectrum. Using this signal to lock the laser frequency, we can ensure that the frequency of the laser changes with the amount of AOM shift. Therefore, the magneto-optical trap （MOT）-molasses process can be implemented smoothly.展开更多
Based on the rate equations, we have investigated three types of chaos synchronizations in injection-locked semiconductor lasers with optical feedback. Numerical simulation shows that the synchronization can be realiz...Based on the rate equations, we have investigated three types of chaos synchronizations in injection-locked semiconductor lasers with optical feedback. Numerical simulation shows that the synchronization can be realized by the symmetric or asymmetric laser systems. Also, the influence of parameter mismatches on chaos synchronization is investigated, and the results imply that these two lasers can achieve good synchronization, with smaller tolerance of parameter mismatch existing.展开更多
This paper investigates the influences of a semiconductor laser with narrow linewidth on a fibre-optic distributed disturbance sensor based on Mach-Zehnder interferometer. It establishes an effective numerical model t...This paper investigates the influences of a semiconductor laser with narrow linewidth on a fibre-optic distributed disturbance sensor based on Mach-Zehnder interferometer. It establishes an effective numerical model to describe the noises and linewidth of a semiconductor laser, taking into account their correlations. Simulation shows that frequency noise has great influences on location errors and their relationship is numerically investigated. Accordingly, there is need to determine the linewidth of the laser less than a threshold and obtain the least location errors. Furthermore, experiments are performed by a sensor prototype using three semiconductor lasers with different linewidths, respectively, with polarization maintaining optical fibres and couplers to eliminate the polarization induced noises and fading. The agreement of simulation with experimental results means that the proposed numerical model can make a comprehensive description of the noise behaviour of a semiconductor laser. The conclusion is useful for choosing a laser source for fibre-optic distributed disturbance sensor to achieve optimized location accuracy. What is more, the proposed numerical model can be widely used for analysing influences of semiconductor lasers on other sensing, communication and optical signal processing systems.展开更多
We use traveling wave coupling theory to investigate the time domain characteristics of tapered semiconductor lasers with DBR gratings.We analyze the influence of the length of second order gratings on the power and s...We use traveling wave coupling theory to investigate the time domain characteristics of tapered semiconductor lasers with DBR gratings.We analyze the influence of the length of second order gratings on the power and spectrum of output light,and optimizing the length of gratings,in order to reduce the mode competition effect in the device,and obtain the high power output light wave with good longitudinal mode characteristics.展开更多
Narrow linewidth light source is a prerequisite for high-performance coherent optical communication and sensing.Waveguide-based external cavity narrow linewidth semiconductor lasers(WEC-NLSLs)have become a competitive...Narrow linewidth light source is a prerequisite for high-performance coherent optical communication and sensing.Waveguide-based external cavity narrow linewidth semiconductor lasers(WEC-NLSLs)have become a competitive and attractive candidate for many coherent applications due to their small size,volume,low energy consumption,low cost and the ability to integrate with other optical components.In this paper,we present an overview of WEC-NLSLs from their required technologies to the state-of-the-art progress.Moreover,we highlight the common problems occurring to current WEC-NLSLs and show the possible approaches to resolving the issues.Finally,we present the possible development directions for the next phase and hope this review will be beneficial to the advancements of WEC-NLSLs.展开更多
We design a hybrid integrated chaotic semiconductor laser with short-cavity optical feedback.It can be assembled in a commercial butterfly shell with just three micro-lenses.One of them is coated by a transflective fi...We design a hybrid integrated chaotic semiconductor laser with short-cavity optical feedback.It can be assembled in a commercial butterfly shell with just three micro-lenses.One of them is coated by a transflective film to provide the optical feedback for chaos generation while insuring regular laser transmission.We prove the feasibility of the chaos generation in this compact structure and provide critical external parameters for the fabrication by theoretical simulations.Rather than the usual changeless internal parameters used in previous simulation research,we extract the real parameters of the chip by experiment.Moreover,the maps of the largest Lyapunov exponent with varying bias current and feedback intensity Kap demonstrate the dynamic characteristics under different external-cavity conditions.Each laser chip has its own optimal external cavity length(L)and feedback intensity(Kap)to generate chaos because of the different internal parameters.We have acquired two ranges of optimal parameters(L=4 mm,0.12〈Kap〈0.2 and L=5 mm,0.07〈Kap〈0.12)for two different chips.展开更多
The epitaxial growth conditions and performance of a diode-pumped GaSb-based optically pumped semiconductor disk laser(SDL) emitting near 2.0 μm in an external cavity configuration are reported. The high quality epit...The epitaxial growth conditions and performance of a diode-pumped GaSb-based optically pumped semiconductor disk laser(SDL) emitting near 2.0 μm in an external cavity configuration are reported. The high quality epitaxial structure,grown on Te-doped(001) oriented GaSb substrate by molecular beam epitaxy, consists of a distributed Bragg reflector(DBR), a multi-quantum-well gain region, and a window layer. An intra-cavity SiC heat spreader was attached to the gain chip for effective thermal management. A continuous-wave output power of over 1 W operating at 2.03 μm wavelength operating near room temperature was achieved using a 3% output coupler.展开更多
文摘We propose a theoretical model to describe external-cavity distributed feedback semiconductor lasers and investigate the impact of the number of external feedback points on linewidth and side-mode suppression ratio through numerical simulation. The simulation results demonstrate that the linewidth of external-cavity semiconductor lasers can be reduced by increasing the external cavity length and feedback ratio, and adding more external feedback points can further narrow the linewidth and enhance the side mode suppression ratio. This research provides insight into the external cavity distributed feedback mechanism and can guide the design of high-performance external cavity semiconductor lasers. .
基金This work was supported by the National Natural Science Foundation of China(Grant no.62171087,61671119)the Sichuan Science and Technology Program(Grant no.2021JDJQ0023)the Fundamental Research Funds for the Central Universities(Grant no.ZYGX2019J003).
文摘A novel scheme for generating optical chaos is proposed and experimentally demonstrated,which supports to simultaneously produce two low-correlation chaotic signals with wideband spectrum and suppressed time-delay-signature(TDS).In the proposed scheme,we use the output of an external-cavity semiconductor laser(ECSL)as the driving signal of a phase modulator to modulate the output of a CW laser.Then the phase-modulated continuous-wave(CW)light is split into two parts,one is injected back into the ECSL that outputs one chaotic signal,while the other part is passed through a dispersion module for generating another chaotic signal simultaneously.The experimental results prove that the proposed scheme has three merits.Firstly,it can improve the bandwidth of ECSL-based chaos by several times,and simultaneously generate another wideband flat-spectrum chaotic signal.Secondly,the undesired TDS characteristics of the simultaneously-generated chaotic signals can be efficiently suppressed to an indistinguishable level within a wide parameter range,as such the complexities of the chaotic signals are considerably high.Thirdly,the correlation coefficient between these two simultaneously-generated chaotic signals is smaller than 0.1.The proposed scheme provides an attractive solution for parallel multiple chaos generation,and shows great potential for multiple channel chaos communications and multiple random bit generations.
基金Project supported by the National Natural Science Foundation of China(Grant No.61974141)Tianjin Municipal Science and Technology BureauScience and Technology Innovation Bureau of China-Singapore Tianjin Eco-City。
文摘We demonstrate high-performance broadband tunable external-cavity lasers(ECLs) with the metal-organic chemical vapor deposition(MOCVD) grown In As/In P quantum dots(QDs) structures. Without cavity facet coatings, the 3-d B spectral bandwidth of the Fabry–Perot(FP) laser is approximately 10.8 nm, while the tuning bandwidth of ECLs is 45 nm.Combined with the anti-reflection(AR)/high-reflection(HR) facet coating, a 92 nm bandwidth tuning range has been obtained with the wavelength covering from 1414 nm to 1506 nm. In most of the tuning range, the threshold current density is lower than 1.5 k A/cm2. The maximum output power of 6.5 m W was achieved under a 500 m A injection current.All achievements mentioned above were obtained under continuous-wave(CW) mode at room temperature(RT).
基金supported by the National Natural Science Foundation of China (Grant No 50575110)
文摘External-cavity birefringence feedback effects of the microchip Nd：YAG laser are presented. When a birefringence element is placed in the external feedback cavity of the laser, two orthogonally polarized laser beams with a phase difference are output. The phase difference is twice as large as the phase retardation in the external cavity along the two orthogonal directions. The variable extra-cavity birefringence, caused by rotation of the external-cavity birefringenee element, results in tunable phase difference between the two orthogonally polarized beams. This means that the roll angle information has been translated to phase difference of two output laser beams. A theoretical analysis based on the Fabry-Perot cavity equivalent model and refractive index ellipsoid is presented, which is in good agreement with the experimental results. This phenomenon has potential applications for roll angle measurement.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11174098 and 11574107the SelfDetermined Research Funds of Central China Normal University under Grant No CCNU15A02034
文摘We report an external cavity quantum cascade laser （EC-QCL） operating near 6.9μm using the Littman Metcalf configuration. The EC-QCL works in a pulsed mode and can be tuned continuously from 1340 to 1640cm^-1 by only tilting the tuning mirror. The fine tuning ability of the EC-QCL is demonstrated by measuring the absorption spectrum of water in the ambient air with a lock-in amplifier.
基金Project supported by the Chongqing Research Program of Basic Research and Frontier Technology(Grant No.cstc2015jcyj BX0098)the National Natural Science Foundation of China(Grant No.61575011)the Foundation for the Creative Research Groups of Higher Education of Chongqing(Grant No.CXTDX201601016)
文摘High power optically pumped vertical-external-cavity surface-emitting lasers with front and end pump are re-ported.The gain chip consists of 15 repeats of In0.26GaAs/GaAsP0.02 multiple quantum wells and 30 pairs of Alo.2GaAs/Alo.98GaAs distributed Bragg reflectors.The maximum output power of 3 W,optical-to-optical conversion efficiency of 22.4%,and slope efficiency of 29.8%are obtained with 5-℃heatsink temperature under the front pump,while the maximum output power of 1.1 W,optical-to-optical conversion efficiency of 23.2%,and slope efficiency of 30.8%are reached with 5-℃heatsink temperature under the end pump.Influences of thermal effects on the output power of the laser with front and end pump are discussed.
基金Project supported by the National Natural Science Foundation of China (Grant Nos 60527003,60608011 and 60878003)the State Key Program for Basic Research of China (Grant No 2007CB316501)
文摘By using an external-cavity frequency-doubling master oscillator fiber power amplifier （MOPA）, a 700 mW continuous-wave single-frequency laser source at 780 nm is produced. It is shown that the frequency doubling efficiency is improved when the seed diode laser is optically locked to a resonant frequency of a confocal Fabry-Perot （F-P） cavity. This phenomenon can be attributed to the narrowing of the 1.56 μm laser linewidth and explained by our presented theoretical model. The experimental results are found to be in good agreement with the theoretical predictions.
基金supported by the National Natural Science Foundation of China(Grant Nos.62450006,62304217,62274157,62127807,62234011,62034008,62074142,62074140)Tianshan Innovation Team Program(Grant No.2022TSYCTD0005)+1 种基金Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB0880000)Youth Innovation Promotion Association of the Chinese Academy of Sciences(Grant Nos.2023124,Y2023032)。
文摘The 193 nm deep-ultraviolet(DUV)laser plays a critical role in advanced semiconductor chip manufacturing[1,2],micro-nano material characterization[3,4]and biomedical analysis[5,6],due to its high spatial resolution and short wavelength.Efficient and compact 193 nm DUV laser source thus becomes a hot research area.Currently,193 nm Ar F excimer gas laser is widely employed in DUV lithography systems and serves as the enabling technology for 7 and 5 nm semiconductor fabrication.
文摘Influence produced by the heat effect at work of the laser instrument crystal of the semiconductor, the text designs a kind of temperature control system to the crystal of the laser instrument, using the thought and method of the classical control theory to analyze this temperature control system, and establishes mathematics model. According to mathematics model the text demonstrated the system at S field and time- area, and proposed optimizing basis to the total mark of proportion and differential parameter to con- troller PID, thus proposed a kind of temperature control scheme. And the thermostatically system is simulated by MATLAB.
文摘A fitting process is used to measure the cavity loss and the quasi Fermi level separation for Fabry Pérot semiconductor lasers.From the amplified spontaneous emission (ASE) spectrum,the gain spectrum and single pass ASE obtained by the Cassidy method are applied in the fitting process.For a 1550nm quantum well InGaAsP ridge waveguide laser,the cavity loss of about ～24cm -1 is obtained.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61274046,61335009,61201103,and 61320106013)the National High Technology Research and Development Program of China(Grant No.2013AA014202)
文摘Internal loss is a key internal parameter for high power 1060-nm InGaAs/A1GaAs semiconductor laser. In this paper, we discuss the origin of internal loss of 1060-nm InGaAs/GaAs quantum welt （QW） AIGaAs separate confinement het- erostructure semiconductor laser, and the method to reduce internal loss. By light doping the n-cladding layer, and stepwise doping the p-cladding layer combined with the expanded waveguide layer, a broad area laser with internal loss of 1/cm is designed and fabricated. Ridge waveguide laser with an output power of 350 mW is obtained. The threshold current and slope efficiency near the threshold current are 20 mA and 0.8 W/A, respectively.
文摘We solve the single mode coupled rate equations by computer,simulate the behavior of a gain switch of an AlGaInP red light semiconductor laser diode,and find the characteristic of FWHM of pulses changing with the amplitude of modulation signal, the bias current, and the modulated frequency. On this basis, we conduct experiments. The experiment results accord with the simulations well.
基金supported by the National Natural Science Foundation of China(Grant Nos.61178011,11204248,61475127,and 61275116)the Natural Science Foundation of Chongqing City,China(Grant Nos.2012jj B40011 and 2012jj A40012)the Open Fund of the State Key Lab of Millimeter Waves of China(Grant No.K201418)
文摘Based on a semiconductor laser （SL） with incoherent optical feedback, a novel all-optical scheme for generating tunable and broadband microwave frequency combs （MFCs） is proposed and investigated numerically. The results show that, under suitable operation parameters, the SL with incoherent optical feedback can be driven to operate at a regular pulsing state, and the generated MFCs have bandwidths broader than 40 GHz within a 10 dB amplitude variation. For a fixed bias current, the line spacing （or repetition frequency） of the MFCs can be easily tuned by varying the feedback delay time and the feedback strength, and the tuning range of the line spacing increases with the increase in the bias current. The linewidth of the MFCs is sensitive to the variation of the feedback delay time and the feedback strength, and a linewidth of tens of KHz can be achieved through finely adjusting the feedback delay time and the feedback strength. In addition, mappings of amplitude variation, repetition frequency, and linewidth of MFCs in the parameter space of the feedback delay time and the feedback strength are presented.
基金Project supported by the National Key Scientific Instrument and Equipment Development Project,China(Grant No.2014YQ35046103)
文摘We introduce a new method of simultaneously implementing frequency stabilization and frequency shift for semiconductor lasers. We name this method the frequency tunable modulation transfer spectroscopy （FTMTS）. To realize a stable output of 780 nm semiconductor laser, an FTMTS optical heterodyne frequency stabilization system is constructed. Before entering into the frequency stabilization system, the probe laser passes through an acousto-optical modulator （AOM） twice in advance to achieve tunable frequency while keeping the light path stable. According to the experimental results, the frequency changes from 120 MHz to 190 MHz after the double-pass AOM, and the intensity of laser entering into the system is greatly changed, but there is almost no change in the error signal of the FTMTS spectrum. Using this signal to lock the laser frequency, we can ensure that the frequency of the laser changes with the amount of AOM shift. Therefore, the magneto-optical trap （MOT）-molasses process can be implemented smoothly.
文摘Based on the rate equations, we have investigated three types of chaos synchronizations in injection-locked semiconductor lasers with optical feedback. Numerical simulation shows that the synchronization can be realized by the symmetric or asymmetric laser systems. Also, the influence of parameter mismatches on chaos synchronization is investigated, and the results imply that these two lasers can achieve good synchronization, with smaller tolerance of parameter mismatch existing.
文摘This paper investigates the influences of a semiconductor laser with narrow linewidth on a fibre-optic distributed disturbance sensor based on Mach-Zehnder interferometer. It establishes an effective numerical model to describe the noises and linewidth of a semiconductor laser, taking into account their correlations. Simulation shows that frequency noise has great influences on location errors and their relationship is numerically investigated. Accordingly, there is need to determine the linewidth of the laser less than a threshold and obtain the least location errors. Furthermore, experiments are performed by a sensor prototype using three semiconductor lasers with different linewidths, respectively, with polarization maintaining optical fibres and couplers to eliminate the polarization induced noises and fading. The agreement of simulation with experimental results means that the proposed numerical model can make a comprehensive description of the noise behaviour of a semiconductor laser. The conclusion is useful for choosing a laser source for fibre-optic distributed disturbance sensor to achieve optimized location accuracy. What is more, the proposed numerical model can be widely used for analysing influences of semiconductor lasers on other sensing, communication and optical signal processing systems.
文摘We use traveling wave coupling theory to investigate the time domain characteristics of tapered semiconductor lasers with DBR gratings.We analyze the influence of the length of second order gratings on the power and spectrum of output light,and optimizing the length of gratings,in order to reduce the mode competition effect in the device,and obtain the high power output light wave with good longitudinal mode characteristics.
基金Jiangsu Province Key R&D Program(Industry Prospect and Common Key Technologies)(No.BE2014083)Jiangxi Natural Science Foundation Project(No.2019ACBL20054)。
文摘Narrow linewidth light source is a prerequisite for high-performance coherent optical communication and sensing.Waveguide-based external cavity narrow linewidth semiconductor lasers(WEC-NLSLs)have become a competitive and attractive candidate for many coherent applications due to their small size,volume,low energy consumption,low cost and the ability to integrate with other optical components.In this paper,we present an overview of WEC-NLSLs from their required technologies to the state-of-the-art progress.Moreover,we highlight the common problems occurring to current WEC-NLSLs and show the possible approaches to resolving the issues.Finally,we present the possible development directions for the next phase and hope this review will be beneficial to the advancements of WEC-NLSLs.
基金Project supported by the International Science and Technology Cooperation Program of China(Grant No.2014DFA50870)the National Natural Science Foundation of China(Grant Nos.61377089,61475111,and 61527819)+4 种基金Shanxi Province Natural Science Foundation,China(Grant No.2015011049)Shanxi Province Youth Science and Technology Foundation,China(Grant No.201601D021069)Shanxi Scholarship Council of China(Grant No.2016-036)Program for the Outstanding Innovative Teams of Higher Learning Institutions of Shanxi,ChinaProgram for Sanjin Scholar,China
文摘We design a hybrid integrated chaotic semiconductor laser with short-cavity optical feedback.It can be assembled in a commercial butterfly shell with just three micro-lenses.One of them is coated by a transflective film to provide the optical feedback for chaos generation while insuring regular laser transmission.We prove the feasibility of the chaos generation in this compact structure and provide critical external parameters for the fabrication by theoretical simulations.Rather than the usual changeless internal parameters used in previous simulation research,we extract the real parameters of the chip by experiment.Moreover,the maps of the largest Lyapunov exponent with varying bias current and feedback intensity Kap demonstrate the dynamic characteristics under different external-cavity conditions.Each laser chip has its own optimal external cavity length(L)and feedback intensity(Kap)to generate chaos because of the different internal parameters.We have acquired two ranges of optimal parameters(L=4 mm,0.12〈Kap〈0.2 and L=5 mm,0.07〈Kap〈0.12)for two different chips.
基金supported by the Major Program of the National Natural Science Foundation of China(Grant Nos.61790581,61790582,and 61790584)the National Natural Science Foundation of China(Grant No.61435012)the Scientific Instrument Developing Project of the Chinese Academy of Sciences(Grant No.YJKYYQ20170032)
文摘The epitaxial growth conditions and performance of a diode-pumped GaSb-based optically pumped semiconductor disk laser(SDL) emitting near 2.0 μm in an external cavity configuration are reported. The high quality epitaxial structure,grown on Te-doped(001) oriented GaSb substrate by molecular beam epitaxy, consists of a distributed Bragg reflector(DBR), a multi-quantum-well gain region, and a window layer. An intra-cavity SiC heat spreader was attached to the gain chip for effective thermal management. A continuous-wave output power of over 1 W operating at 2.03 μm wavelength operating near room temperature was achieved using a 3% output coupler.
