In the urban environment,subsurface contamination is caused by municipal solid waste(MSW)and industrial and agricultural discharges.About 2.01 billion tons of MSW is generated globally each year,most of which is dispo...In the urban environment,subsurface contamination is caused by municipal solid waste(MSW)and industrial and agricultural discharges.About 2.01 billion tons of MSW is generated globally each year,most of which is disposed of in landfills.Countries in Asia and Pacific regions account for 43%of global waste generation,while India and China account for 27.45%of global waste generation.Most of the landfills operated in South-Asian countries are non-sanitary,leading to the percolation of leachate in the subsurface.Conventional hydrogeological and geochemical methods are primary indicators and detect high levels of critical parameters near landfills,indicating subsurface contamination from leachate.展开更多
To minimize negative effects of geostress distribution on mining safety near the fault areas, the UPM40 triaxial geostress testing system was introduced to conduct in-situ geostress measurements at three sites and nin...To minimize negative effects of geostress distribution on mining safety near the fault areas, the UPM40 triaxial geostress testing system was introduced to conduct in-situ geostress measurements at three sites and nine points by the borehole stress-relief method. The results of strain?confining pressure curves show that rock masses at the three measuring sites exhibit comprehensive linear elasticity in spite of various fissures or cracks within rocks. Horizontal and vertical stress components distribute discrepantly near the fault areas, and the maximum lateral pressure coefficient is as high as 6.15. The maximum principle stress ranges from 8.01 to 14.93 MPa, and stress directions are in the range of N78.07°W?N17.55°W. Geostresses near fault areas are dominated by the horizontal tectonic stresses, while the lower values, compared to those under similar geological conditions are due to stress release by the fault. Additionally, the fault and shear stress nearby are partially responsible for asymmetric elongation and southwesterly migration of orebodies.展开更多
To improve the land surface simulation in the arid and semi-arid areas of northern China, the observational data from two field experiments in Dunhuang and Tongyu are used to optimize the parameters in the land surfac...To improve the land surface simulation in the arid and semi-arid areas of northern China, the observational data from two field experiments in Dunhuang and Tongyu are used to optimize the parameters in the land surface model, BATS, through calibration with the multicriteria method. Sensitivity analysis to the parameters in Dunhuang and Tongyu indicates that different parameters need to be calibrated in two sites with different environmental and climate regimes. Comparison of observed sensible heat flux, latent heat flux, and ground surface temperature with the simulated ones shows the simulations with the optimized parameters have been substantially improved. Especially, the holistic simulations with the calibration of the parameter values are much closer to the observations in the arid region （Dunhuang）, and the energy partition with the calibrated parameters can also be simulated well in the semi-arid region （Tongyu）. Whole results demonstrate that the parameter calibration of the land surface model is important when the model is to be used to investigate the land-air interaction.展开更多
We applied the reflectivity method and the constrained sparse spike inverse modeling(CSSI) method to the interpretation of coal field lithologic seismic data.After introducing the principles of these two methods we di...We applied the reflectivity method and the constrained sparse spike inverse modeling(CSSI) method to the interpretation of coal field lithologic seismic data.After introducing the principles of these two methods we discuss some parameters of a geological model involving possible gas enriched areas or intruded igneous rock.The geological model was constructed and a 60 Hz seismic response profile was obtained looking for igneous rock intrusion and coked areas of the coal seam using the reflectivity method.Starting from synthesized logging data from two wells and a synthesized seismic wavelet we calibrated the model to show accurate strata.Finally,we predicted the lithology within a 10 m igneous rock area,a 3 m coal seam area,and a coked area using the CSSI technique.The results show that the CSSI technique can identify hard to recognize lithologic features that normal profil-ing methods might miss.It can quantitatively analyze and evaluate the intrusive area,the coked area,and the gas-enriched area.展开更多
Debris flows are the one type of natural disaster that is most closely associated with hu- man activities. Debris flows are characterized as being widely distributed and frequently activated. Rainfall is an important ...Debris flows are the one type of natural disaster that is most closely associated with hu- man activities. Debris flows are characterized as being widely distributed and frequently activated. Rainfall is an important component of debris flows and is the most active factor when debris flows oc- cur. Rainfall also determines the temporal and spatial distribution characteristics of the hazards. A reasonable rainfall threshold target is essential to ensuring the accuracy of debris flow pre-warning. Such a threshold is important for the study of the mechanisms of debris flow formation, predicting the characteristics of future activities and the design of prevention and engineering control measures. Most mountainous areas have little data regarding rainfall and hazards, especially in debris flow forming re- gions. Therefore, both the traditional demonstration method and frequency calculated method cannot satisfy the debris flow pre-warning requirements. This study presents the characteristics of pre-warning regions, included the rainfall, hydrologic and topographic conditions. An analogous area with abundant data and the same conditions as the pre-warning region was selected, and the rainfall threshold was calculated by proxy. This method resolved the problem of debris flow pre-warning in ar- eas lacking data and provided a new approach for debris flow pre-warning in mountainous areas.展开更多
An experimental method of measuring the real contact area of transparent blocks based on the principle of total internal reflection is presented, intending to support the investigation of friction characteristics, hea...An experimental method of measuring the real contact area of transparent blocks based on the principle of total internal reflection is presented, intending to support the investigation of friction characteristics, heat conduction, and energy dissipation at the contact interface. A laser sheet illuminates the contact interface, and the transmitted laser sheet is projected onto a screen. Then the contact information is acquired from the screen by a camera. An improved Otsu method is proposed to process the data of experimental images. It can compute the threshold of the overall image and filter out all the pixels one by one. Through analyzing the experimental results, we describe the relationship between the real contact area and the positive pressure during a continuous loading process, at different loading rates, with the polymethyl methacrylate（PMMA）material. A hysteresis phenomenon in the relationship between the real contact area and the positive pressure is found and explained.展开更多
Three-dimensional（3D） geometric models with different comer angles （90° and 120°） and with or without inner round fillets in the bottom die were designed. Some important process parameters were regarded ...Three-dimensional（3D） geometric models with different comer angles （90° and 120°） and with or without inner round fillets in the bottom die were designed. Some important process parameters were regarded as the calculation conditions used in DEFORMTM-3D software, such as stress--strain data of compression test for AZ31 magnesium, temperatures of die and billet, and friction coefficient. Influence of friction coefficient on deformation process was discussed. The results show that reasonable lubrication condition is important to plastic deformation. The change characteristics for distributions of effective stress and strain during an equal channel angular extrusion （ECAE） process with inner angle of 90° and without fillets at outer comer were described. Inhomogeneity index （C） was defined and deformation heterogeneity of ECAE was analyzed from the simulation and experiment results. The deformation homogeneity caused by fillets at outer comer increased compared with the die without fillets. The cumulated maximum strains decrease with increasing the fillets of outer comer in ECAE die and the inner comer angle. The analysis results show that better structures of ECAE die including appropriate outer comer fillet and the inner comer angle of 90° for the die can improve the strain and ensure plastic deformation homogenization to a certain extent. The required extrusion force drops with increasing the fillet made at outer comer in ECAE die. It is demonstrated that the prediction results are in good agreement with experiments and the theoretical calculation and the research conclusions in literatures.展开更多
There are large deltaic systems in the Triassic Yanchang Formation in the northern Shaanxi area of the Ordos Basin, and developed two sets of good source-reservoir-caprock assemblages and many sets of oil-bearing beds...There are large deltaic systems in the Triassic Yanchang Formation in the northern Shaanxi area of the Ordos Basin, and developed two sets of good source-reservoir-caprock assemblages and many sets of oil-bearing beds. Exploration experience demonstrates that the formation and distribution of the reservoir were controlled by the generative depression of the Yanchang Formation, and deltaic reservoir sand body is the material basis for large-scale oilfields. In addition, secondary laumontite in a low permeable area was dissolved and then a high permeable area was formed. The updip lithologic variety of reservoir sand bodies is favorable to the formation of subtle lithologic traps, and the deltaic reservoirs are characterized by large multi-beds of oil-generation and abundant hydrocarbon resources. In this paper, the petroleum geologic settings of the studied area are analyzed, and the accumulation characteristics and exploration methods of lithologic reservoirs are summarized. It is of theoretical significance for the study of the exploration theories of lithologic reservoirs, and also expedites the exploration steps of deltaic reservoirs in the northern Shaanxi area.展开更多
The simulation of real contact area between materials is foundationally important for the contact mechanics of mechanical structures. The Greenwood and Williamson(GW) model and the Majumdar(MB) model are the basic mod...The simulation of real contact area between materials is foundationally important for the contact mechanics of mechanical structures. The Greenwood and Williamson(GW) model and the Majumdar(MB) model are the basic models in this field, which are widely accepted and proven to be valid in many experiments and engineering. Although the contact models have evolved considerably in recent years, the verifications of the models are most based on the indirect methods such as electrical conductivity and contact stiffness, because of the lack of effective methods to directly measure the variation of contact surface. In this paper, the total reflection(TR) method is introduced into the verification of contact models.An experiment system based on TR method is constructed to measure the real contact area of two PMMA specimens. The comparison analysis between the results of experiment and models suggests that the experiment result has the same trend with simulation, the MB model has better agreement with the experimental result because this method can take into account the variation of radius and the merging of asperities, while the GW model has a huge deviation because of the dependence on resolution and the lack of considering the variation of radius and asperity's merging process. Taking the interaction of asperities into account could give a better result that is closer to the experiment. Our results and analysis prove that the experimental methods in this paper could be used as a more direct and valid method to quantitatively measure the real contact area and to verify the contact models.展开更多
In this study, we developed a computer program for automatic prediction of watering time point by considering the environmental factors such as solar radiation, air temperature and relative humidity based on the multi...In this study, we developed a computer program for automatic prediction of watering time point by considering the environmental factors such as solar radiation, air temperature and relative humidity based on the multiple linear regression equation of leaf area and Penman Method. The experiments were carried out for a year in two watering experimental plots, one of which was controlled by pF value, and the other by the computer program. After comparing the results of the two plots, the following findings were obtained. In the computer program plot, the observed and predicted values of both leaf area and evapotranspiration indicated significant correlation at the 1% level, which suggested that the computer program had high prediction accuracy. In addition, no significant difference was observed between the two experimental plots with respects to the plant height, plant diameter, leaf area, leaf number, fresh weight, and dry weight, which demonstrated that the plants in the computer program plot had normal growth. On the other hand, although the number of flower buds and flowering shoots showed higher values at the end of certain cultivations in the computer program plot than those in pF value plot, we proposed that it was due to the effect of cumulative daily solar radiation in the greenhouse, rather than the watering. Thus, we have reached the conclusion that the computer program for automatic prediction of watering time point developed by this study has high applicability in miniature pot rose production.展开更多
Monte-Carlo method is used for estimating coalbed methane （CBM） resources in key coal mining areas of China. Monte-Carlo method is shown to be superior to the traditional volumetric method with constant parameters i...Monte-Carlo method is used for estimating coalbed methane （CBM） resources in key coal mining areas of China. Monte-Carlo method is shown to be superior to the traditional volumetric method with constant parameters in the calculation of CBM resources. The focus of the article is to introduce the main algorithm and the realization of functions estimated by Monte-Carlo method, including selection of parameters, determination of distribution function, generation of pseudo-random numbers, and evaluation of the parameters corresponding to pseudo-random numbers. A specified software on the basis of Monte-Carlo method is developed using Visual C＋＋ for the assessment of the CBM resources. A case study shows that calculation results using Monte-Carlo method have smaller error range in comparison with those using volumetric method.展开更多
The method for preparing yttrium oxide with large specific surface area was introduced. By means of BET, SEM, TG and DTA analysis, the effects of precipitant, stirring velocity, non-RE impurity in solution, calcinatio...The method for preparing yttrium oxide with large specific surface area was introduced. By means of BET, SEM, TG and DTA analysis, the effects of precipitant, stirring velocity, non-RE impurity in solution, calcination temperature, on the surface area were studied respectively. The Y_2O_3 sample with specific surface area of more than 60 m^2·g^(-1) and L.O.I less than 1% was prepared in the suitable precipitation condition and calcinations temperature when the ammonia used as precipitant. The SEM shows that the Y_2O_3 prepared with large surface area is the aggregation of about 50 nm particles.展开更多
This paper proves that the weighting method via modified Gram-Schmidt（MGS） for solving the equality constrained least squares problem in the limit is equivalent to the direct elimination method via MGS（MGS-eliminat...This paper proves that the weighting method via modified Gram-Schmidt（MGS） for solving the equality constrained least squares problem in the limit is equivalent to the direct elimination method via MGS（MGS-elimination method）. By virtue of this equivalence, the backward and forward roundoff error analysis of the MGS-elimination method is proved. Numerical experiments are provided to verify the results.展开更多
Adopting the quasi-three-dimensional （Quasi-3D） numerical method to optimize the anti-freeze design parameters of an underground pipeline usually involves heavy numerical calculations. Here, the fitting formulae bet...Adopting the quasi-three-dimensional （Quasi-3D） numerical method to optimize the anti-freeze design parameters of an underground pipeline usually involves heavy numerical calculations. Here, the fitting formulae between the safe con-veyance distance （SCD） of a water pipeline and six influencing factors are established based on the lowest water temper-ature （LWT） along the pipeline axis direction. With reference to the current widely used anti-freeze design approaches for underground pipelines in seasonally frozen areas, this paper first analyzes the feasibility of applying the maximum frozen penetration （MFP） instead of the mean annual ground surface temperature （MAGST） and soil water content （SWC） to calculate the SCD. The results show that the SCD depends on the buried depth if the MFP is fixed and the variation of the MAGST and SWC combination does not significantly change the SCD. A comprehensive formula for the SCD is estab-lished based on the relationships between the SCD and several primary influencing factors and the interaction among them. This formula involves five easy-to-access parameters： the MFP, buried depth, pipeline diameter, flow velocity, and inlet water temperature. A comparison between the analytical method and the numerical results based on the Quasi-3D method indicates that the two methods are in good agreement overall. The analytic method can be used to optimize the anti-freeze design parameters of underground water pipelines in seasonally frozen areas under the condition of a 1.5 safety coefficient.展开更多
In this paper,we present a smoothing Newton-like method for solving nonlinear systems of equalities and inequalities.By using the so-called max function,we transfer the inequalities into a system of semismooth equalit...In this paper,we present a smoothing Newton-like method for solving nonlinear systems of equalities and inequalities.By using the so-called max function,we transfer the inequalities into a system of semismooth equalities.Then a smoothing Newton-like method is proposed for solving the reformulated system,which only needs to solve one system of linear equations and to perform one line search at each iteration. The global and local quadratic convergence are studied under appropriate assumptions. Numerical examples show that the new approach is effective.展开更多
The CeO_2-ZrO_2 solid solutions were prepared by a reverse microemulsion method. The effect of preparation parameters on the surface area and crystalline form of the solid solutions were studied by the BET surface are...The CeO_2-ZrO_2 solid solutions were prepared by a reverse microemulsion method. The effect of preparation parameters on the surface area and crystalline form of the solid solutions were studied by the BET surface area and XRD analysis. The studies indicate that the separation of the microemulsion phase during the preparation procedure can decrease the specific surface area of sample, adding hydrogen peroxide in the matrix solution can increase the specific surface area and stability of sample. The surface area of sample calcined at 550 ℃ for 5 h is 149 m^2·g^(-1), and that calcined at 900 ℃ for 6 h is 88 m^2·g^(-1). The sample with tetragonal symmetry Ce_(0.5)Zr_(0.5)O_2 phase has a higher stability.展开更多
We fabricate flexible conductive and transparent graphene films on position-emission-tomography substrates and prepare large area graphene films by graphite oxide sheets with the new technical process. The multi-layer...We fabricate flexible conductive and transparent graphene films on position-emission-tomography substrates and prepare large area graphene films by graphite oxide sheets with the new technical process. The multi-layer graphene oxide sheets can be chemically reduced by HNO3 and HI to form a highly conductive graphene film on a substrate at lower temperature. The reduced graphene oxide sheets show a high conductivity sheet with resistance of 476Ω/sq and transmittance of 76% at 550nm （6 layers）. The technique used to produce the transparent conductive graphene thin film is facile, inexpensive, and can be tunable for a large area production applied for electronics or touch screens.展开更多
The distribution and characteristics of nonmetallic micro-inclusions of GCr15 bearing steel were explored through metallographic area method in virtue of tracer method and electronic microscope.The results show that t...The distribution and characteristics of nonmetallic micro-inclusions of GCr15 bearing steel were explored through metallographic area method in virtue of tracer method and electronic microscope.The results show that the micro-inclusions,of which the average value is 0.032%,are mainly the compounds formed via the adsorption/aggregation of multielement deoxidized compounds and secondarily deoxidized products on tundish liquid level.The micro-inclusions of diameters from 0 to 5 μm are 92.5% in total,which basically determines the characteristics of inclusions distribution in casting slab.The inclusions of diameters more than 10 μm only account for less than 1% in total,which have little influence on steel quality.The relationship between equilibrium compositions of the first deoxidation products and molten steel compositions was also calculated based on thermodynamic theory.展开更多
Through improving the aging process during synthesis of the support, γ-Al2O3 with large pore volume and high surface area was synthesized by a facile secondary reforming method. The synthesis parameters, such as the ...Through improving the aging process during synthesis of the support, γ-Al2O3 with large pore volume and high surface area was synthesized by a facile secondary reforming method. The synthesis parameters, such as the reaction temperature, the first aging temperature and the second aging temperature, were investigated. The textural properties of γ-Al2O3 were characterized by means of N2 adsorption-desorption isotherms, X-ray powder diffractometry （XRD）, scanning electron microscopy （SEM）, Fourier transform infrared （FTIR） spectroscopy and thermogravimetry （TG）. The experimental results indicated that AACH and amorphous A1OOH were the precursors of alumina, which were formed via precipitation from solutions after reaction of aluminum sulphate with ammonium hydrogen carbonate. The precursor nanocrystallites grew and re-assembled during the secondary reforming process, which resulted in an increased pore size and pore volume and a decreased bulk density. The as-synthesized γ-Al2O3 materials featured meso/macroporosity, large pore volume （2.175 cm^3/g）, high surface area （237.8 m^2/g）, and low bulk density （0.284 g/mL）.展开更多
In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new ...In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.展开更多
基金support to bring out this publication(NGRI/Lib/2023/Pub-104)the Department of Science and Technology(DST),Government of India,for the INSPIRE fellowship(IF220569)+1 种基金carried out as a part of the project[GAP-861-28(TA)]supported by the Ministry of Earth Sciences(MoES),India,tenable at CSIR-NGRI,Hyderabad.
文摘In the urban environment,subsurface contamination is caused by municipal solid waste(MSW)and industrial and agricultural discharges.About 2.01 billion tons of MSW is generated globally each year,most of which is disposed of in landfills.Countries in Asia and Pacific regions account for 43%of global waste generation,while India and China account for 27.45%of global waste generation.Most of the landfills operated in South-Asian countries are non-sanitary,leading to the percolation of leachate in the subsurface.Conventional hydrogeological and geochemical methods are primary indicators and detect high levels of critical parameters near landfills,indicating subsurface contamination from leachate.
基金Projects(50934002,51104011)supported by the National Natural Science Foundation of ChinaProject(2012BAB08B02)supported by the National Key Technologies R&D Program during the 12th Five-year Plan of China
文摘To minimize negative effects of geostress distribution on mining safety near the fault areas, the UPM40 triaxial geostress testing system was introduced to conduct in-situ geostress measurements at three sites and nine points by the borehole stress-relief method. The results of strain?confining pressure curves show that rock masses at the three measuring sites exhibit comprehensive linear elasticity in spite of various fissures or cracks within rocks. Horizontal and vertical stress components distribute discrepantly near the fault areas, and the maximum lateral pressure coefficient is as high as 6.15. The maximum principle stress ranges from 8.01 to 14.93 MPa, and stress directions are in the range of N78.07°W?N17.55°W. Geostresses near fault areas are dominated by the horizontal tectonic stresses, while the lower values, compared to those under similar geological conditions are due to stress release by the fault. Additionally, the fault and shear stress nearby are partially responsible for asymmetric elongation and southwesterly migration of orebodies.
基金supported jointlyby the Chinese Academy of Sciences under Grant KZCX2-YW-220the National Basic Research Program of Chinaunder Grant 2009CB421405the National Natural Sci-ence Foundation of China under Grant No.40730952
文摘To improve the land surface simulation in the arid and semi-arid areas of northern China, the observational data from two field experiments in Dunhuang and Tongyu are used to optimize the parameters in the land surface model, BATS, through calibration with the multicriteria method. Sensitivity analysis to the parameters in Dunhuang and Tongyu indicates that different parameters need to be calibrated in two sites with different environmental and climate regimes. Comparison of observed sensible heat flux, latent heat flux, and ground surface temperature with the simulated ones shows the simulations with the optimized parameters have been substantially improved. Especially, the holistic simulations with the calibration of the parameter values are much closer to the observations in the arid region （Dunhuang）, and the energy partition with the calibrated parameters can also be simulated well in the semi-arid region （Tongyu）. Whole results demonstrate that the parameter calibration of the land surface model is important when the model is to be used to investigate the land-air interaction.
基金Projects 40874054 and 40804026 supported by the National Natural Science Foundation of Chinathe National Basic Research Program of China (2007CB209400 and 2009CB219603)the National Key Scientific and Technological Project (2008ZX05035)
文摘We applied the reflectivity method and the constrained sparse spike inverse modeling(CSSI) method to the interpretation of coal field lithologic seismic data.After introducing the principles of these two methods we discuss some parameters of a geological model involving possible gas enriched areas or intruded igneous rock.The geological model was constructed and a 60 Hz seismic response profile was obtained looking for igneous rock intrusion and coked areas of the coal seam using the reflectivity method.Starting from synthesized logging data from two wells and a synthesized seismic wavelet we calibrated the model to show accurate strata.Finally,we predicted the lithology within a 10 m igneous rock area,a 3 m coal seam area,and a coked area using the CSSI technique.The results show that the CSSI technique can identify hard to recognize lithologic features that normal profil-ing methods might miss.It can quantitatively analyze and evaluate the intrusive area,the coked area,and the gas-enriched area.
基金supported by the National Natural Science Foundation of China(Nos.40830742 and 40901007)
文摘Debris flows are the one type of natural disaster that is most closely associated with hu- man activities. Debris flows are characterized as being widely distributed and frequently activated. Rainfall is an important component of debris flows and is the most active factor when debris flows oc- cur. Rainfall also determines the temporal and spatial distribution characteristics of the hazards. A reasonable rainfall threshold target is essential to ensuring the accuracy of debris flow pre-warning. Such a threshold is important for the study of the mechanisms of debris flow formation, predicting the characteristics of future activities and the design of prevention and engineering control measures. Most mountainous areas have little data regarding rainfall and hazards, especially in debris flow forming re- gions. Therefore, both the traditional demonstration method and frequency calculated method cannot satisfy the debris flow pre-warning requirements. This study presents the characteristics of pre-warning regions, included the rainfall, hydrologic and topographic conditions. An analogous area with abundant data and the same conditions as the pre-warning region was selected, and the rainfall threshold was calculated by proxy. This method resolved the problem of debris flow pre-warning in ar- eas lacking data and provided a new approach for debris flow pre-warning in mountainous areas.
基金Project supported by the National Natural Science Foundation of China(Grant No.11272171)the Beijing Natural Science Foundation,China(Grant No.3132030)the Education Ministry Doctoral Fund of China(Grant No.20120002110070)
文摘An experimental method of measuring the real contact area of transparent blocks based on the principle of total internal reflection is presented, intending to support the investigation of friction characteristics, heat conduction, and energy dissipation at the contact interface. A laser sheet illuminates the contact interface, and the transmitted laser sheet is projected onto a screen. Then the contact information is acquired from the screen by a camera. An improved Otsu method is proposed to process the data of experimental images. It can compute the threshold of the overall image and filter out all the pixels one by one. Through analyzing the experimental results, we describe the relationship between the real contact area and the positive pressure during a continuous loading process, at different loading rates, with the polymethyl methacrylate（PMMA）material. A hysteresis phenomenon in the relationship between the real contact area and the positive pressure is found and explained.
基金Project(2007CB613700)supported by National Basic Research Program of ChinaProject(2006BAE04B03)supported by Item of Support Plan during the 11th National Five-Year PlanProjects(CST,2007bb4413)supported by National Science Foundation of Chongqing,China
文摘Three-dimensional（3D） geometric models with different comer angles （90° and 120°） and with or without inner round fillets in the bottom die were designed. Some important process parameters were regarded as the calculation conditions used in DEFORMTM-3D software, such as stress--strain data of compression test for AZ31 magnesium, temperatures of die and billet, and friction coefficient. Influence of friction coefficient on deformation process was discussed. The results show that reasonable lubrication condition is important to plastic deformation. The change characteristics for distributions of effective stress and strain during an equal channel angular extrusion （ECAE） process with inner angle of 90° and without fillets at outer comer were described. Inhomogeneity index （C） was defined and deformation heterogeneity of ECAE was analyzed from the simulation and experiment results. The deformation homogeneity caused by fillets at outer comer increased compared with the die without fillets. The cumulated maximum strains decrease with increasing the fillets of outer comer in ECAE die and the inner comer angle. The analysis results show that better structures of ECAE die including appropriate outer comer fillet and the inner comer angle of 90° for the die can improve the strain and ensure plastic deformation homogenization to a certain extent. The required extrusion force drops with increasing the fillet made at outer comer in ECAE die. It is demonstrated that the prediction results are in good agreement with experiments and the theoretical calculation and the research conclusions in literatures.
文摘There are large deltaic systems in the Triassic Yanchang Formation in the northern Shaanxi area of the Ordos Basin, and developed two sets of good source-reservoir-caprock assemblages and many sets of oil-bearing beds. Exploration experience demonstrates that the formation and distribution of the reservoir were controlled by the generative depression of the Yanchang Formation, and deltaic reservoir sand body is the material basis for large-scale oilfields. In addition, secondary laumontite in a low permeable area was dissolved and then a high permeable area was formed. The updip lithologic variety of reservoir sand bodies is favorable to the formation of subtle lithologic traps, and the deltaic reservoirs are characterized by large multi-beds of oil-generation and abundant hydrocarbon resources. In this paper, the petroleum geologic settings of the studied area are analyzed, and the accumulation characteristics and exploration methods of lithologic reservoirs are summarized. It is of theoretical significance for the study of the exploration theories of lithologic reservoirs, and also expedites the exploration steps of deltaic reservoirs in the northern Shaanxi area.
基金Project supported by the National Natural Science Foundation of China(Grant No.11872033)the Beijing Natural Science Foundation,China(Grant No.3172017)
文摘The simulation of real contact area between materials is foundationally important for the contact mechanics of mechanical structures. The Greenwood and Williamson(GW) model and the Majumdar(MB) model are the basic models in this field, which are widely accepted and proven to be valid in many experiments and engineering. Although the contact models have evolved considerably in recent years, the verifications of the models are most based on the indirect methods such as electrical conductivity and contact stiffness, because of the lack of effective methods to directly measure the variation of contact surface. In this paper, the total reflection(TR) method is introduced into the verification of contact models.An experiment system based on TR method is constructed to measure the real contact area of two PMMA specimens. The comparison analysis between the results of experiment and models suggests that the experiment result has the same trend with simulation, the MB model has better agreement with the experimental result because this method can take into account the variation of radius and the merging of asperities, while the GW model has a huge deviation because of the dependence on resolution and the lack of considering the variation of radius and asperity's merging process. Taking the interaction of asperities into account could give a better result that is closer to the experiment. Our results and analysis prove that the experimental methods in this paper could be used as a more direct and valid method to quantitatively measure the real contact area and to verify the contact models.
基金supported by the Science Founda-tion of Guangxi Zhuang Autonomous Region, China(0832002)
文摘In this study, we developed a computer program for automatic prediction of watering time point by considering the environmental factors such as solar radiation, air temperature and relative humidity based on the multiple linear regression equation of leaf area and Penman Method. The experiments were carried out for a year in two watering experimental plots, one of which was controlled by pF value, and the other by the computer program. After comparing the results of the two plots, the following findings were obtained. In the computer program plot, the observed and predicted values of both leaf area and evapotranspiration indicated significant correlation at the 1% level, which suggested that the computer program had high prediction accuracy. In addition, no significant difference was observed between the two experimental plots with respects to the plant height, plant diameter, leaf area, leaf number, fresh weight, and dry weight, which demonstrated that the plants in the computer program plot had normal growth. On the other hand, although the number of flower buds and flowering shoots showed higher values at the end of certain cultivations in the computer program plot than those in pF value plot, we proposed that it was due to the effect of cumulative daily solar radiation in the greenhouse, rather than the watering. Thus, we have reached the conclusion that the computer program for automatic prediction of watering time point developed by this study has high applicability in miniature pot rose production.
基金supported by the National Natural Science Foundation of China (No. 40730422)the Foundation of China University of Mining & Technology (No. OF061003)State Key Laboratory of Geological Processes and Mineral Resources (No. GPMR2007-11)
文摘Monte-Carlo method is used for estimating coalbed methane （CBM） resources in key coal mining areas of China. Monte-Carlo method is shown to be superior to the traditional volumetric method with constant parameters in the calculation of CBM resources. The focus of the article is to introduce the main algorithm and the realization of functions estimated by Monte-Carlo method, including selection of parameters, determination of distribution function, generation of pseudo-random numbers, and evaluation of the parameters corresponding to pseudo-random numbers. A specified software on the basis of Monte-Carlo method is developed using Visual C＋＋ for the assessment of the CBM resources. A case study shows that calculation results using Monte-Carlo method have smaller error range in comparison with those using volumetric method.
文摘The method for preparing yttrium oxide with large specific surface area was introduced. By means of BET, SEM, TG and DTA analysis, the effects of precipitant, stirring velocity, non-RE impurity in solution, calcination temperature, on the surface area were studied respectively. The Y_2O_3 sample with specific surface area of more than 60 m^2·g^(-1) and L.O.I less than 1% was prepared in the suitable precipitation condition and calcinations temperature when the ammonia used as precipitant. The SEM shows that the Y_2O_3 prepared with large surface area is the aggregation of about 50 nm particles.
基金supported by the Shanghai Leading Academic Discipline Project (Grant No.J50101)
文摘This paper proves that the weighting method via modified Gram-Schmidt（MGS） for solving the equality constrained least squares problem in the limit is equivalent to the direct elimination method via MGS（MGS-elimination method）. By virtue of this equivalence, the backward and forward roundoff error analysis of the MGS-elimination method is proved. Numerical experiments are provided to verify the results.
基金financially supported by the National Basic Research Program of China (No. 2013CBA01803)the National Natural Science Foundation of China (No. 41101065)and the CAS "Equipment Development Project for Scientific Research" (No. YZ201523)
文摘Adopting the quasi-three-dimensional （Quasi-3D） numerical method to optimize the anti-freeze design parameters of an underground pipeline usually involves heavy numerical calculations. Here, the fitting formulae between the safe con-veyance distance （SCD） of a water pipeline and six influencing factors are established based on the lowest water temper-ature （LWT） along the pipeline axis direction. With reference to the current widely used anti-freeze design approaches for underground pipelines in seasonally frozen areas, this paper first analyzes the feasibility of applying the maximum frozen penetration （MFP） instead of the mean annual ground surface temperature （MAGST） and soil water content （SWC） to calculate the SCD. The results show that the SCD depends on the buried depth if the MFP is fixed and the variation of the MAGST and SWC combination does not significantly change the SCD. A comprehensive formula for the SCD is estab-lished based on the relationships between the SCD and several primary influencing factors and the interaction among them. This formula involves five easy-to-access parameters： the MFP, buried depth, pipeline diameter, flow velocity, and inlet water temperature. A comparison between the analytical method and the numerical results based on the Quasi-3D method indicates that the two methods are in good agreement overall. The analytic method can be used to optimize the anti-freeze design parameters of underground water pipelines in seasonally frozen areas under the condition of a 1.5 safety coefficient.
基金supported by Guangdong Provincial Zhujiang Scholar Award Project,National Science Foundation of China(10671163,10871031)the National Basic Research Program under the Grant 2005CB321703Scientific Research Fund of Hunan Provincial Education Department(06A069,06C824)
文摘In this paper,we present a smoothing Newton-like method for solving nonlinear systems of equalities and inequalities.By using the so-called max function,we transfer the inequalities into a system of semismooth equalities.Then a smoothing Newton-like method is proposed for solving the reformulated system,which only needs to solve one system of linear equations and to perform one line search at each iteration. The global and local quadratic convergence are studied under appropriate assumptions. Numerical examples show that the new approach is effective.
文摘The CeO_2-ZrO_2 solid solutions were prepared by a reverse microemulsion method. The effect of preparation parameters on the surface area and crystalline form of the solid solutions were studied by the BET surface area and XRD analysis. The studies indicate that the separation of the microemulsion phase during the preparation procedure can decrease the specific surface area of sample, adding hydrogen peroxide in the matrix solution can increase the specific surface area and stability of sample. The surface area of sample calcined at 550 ℃ for 5 h is 149 m^2·g^(-1), and that calcined at 900 ℃ for 6 h is 88 m^2·g^(-1). The sample with tetragonal symmetry Ce_(0.5)Zr_(0.5)O_2 phase has a higher stability.
基金Supported by the Basic Research Program of Nanjing University of Posts and Telecommunications under Grant No NY212002the Innovative Research Team in University under Grant No IRT1148the 2014 Shuangchuang Program of Jiangsu Province
文摘We fabricate flexible conductive and transparent graphene films on position-emission-tomography substrates and prepare large area graphene films by graphite oxide sheets with the new technical process. The multi-layer graphene oxide sheets can be chemically reduced by HNO3 and HI to form a highly conductive graphene film on a substrate at lower temperature. The reduced graphene oxide sheets show a high conductivity sheet with resistance of 476Ω/sq and transmittance of 76% at 550nm （6 layers）. The technique used to produce the transparent conductive graphene thin film is facile, inexpensive, and can be tunable for a large area production applied for electronics or touch screens.
基金Supported by Natural Science Foundation of Hebei Province (No.502265)
文摘The distribution and characteristics of nonmetallic micro-inclusions of GCr15 bearing steel were explored through metallographic area method in virtue of tracer method and electronic microscope.The results show that the micro-inclusions,of which the average value is 0.032%,are mainly the compounds formed via the adsorption/aggregation of multielement deoxidized compounds and secondarily deoxidized products on tundish liquid level.The micro-inclusions of diameters from 0 to 5 μm are 92.5% in total,which basically determines the characteristics of inclusions distribution in casting slab.The inclusions of diameters more than 10 μm only account for less than 1% in total,which have little influence on steel quality.The relationship between equilibrium compositions of the first deoxidation products and molten steel compositions was also calculated based on thermodynamic theory.
基金the financial support by the Natural Science Foundation of Liaoning Province of China (Grant No. 2013020122)the National Natural Science Foundationof China (Grant No. 21076100 and 51308045)the financial support by the PetroChina Company Limited (Grant No. 10-01A-01-01-01)
文摘Through improving the aging process during synthesis of the support, γ-Al2O3 with large pore volume and high surface area was synthesized by a facile secondary reforming method. The synthesis parameters, such as the reaction temperature, the first aging temperature and the second aging temperature, were investigated. The textural properties of γ-Al2O3 were characterized by means of N2 adsorption-desorption isotherms, X-ray powder diffractometry （XRD）, scanning electron microscopy （SEM）, Fourier transform infrared （FTIR） spectroscopy and thermogravimetry （TG）. The experimental results indicated that AACH and amorphous A1OOH were the precursors of alumina, which were formed via precipitation from solutions after reaction of aluminum sulphate with ammonium hydrogen carbonate. The precursor nanocrystallites grew and re-assembled during the secondary reforming process, which resulted in an increased pore size and pore volume and a decreased bulk density. The as-synthesized γ-Al2O3 materials featured meso/macroporosity, large pore volume （2.175 cm^3/g）, high surface area （237.8 m^2/g）, and low bulk density （0.284 g/mL）.
基金Projects(50471102,50671089) supported by the National Natural Science Foundation of China
文摘In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.
