A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cut...A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cutting conditions, especially for circular milling process. This paper presents an improved cutting force model for circular end milling process based on the typical linear milling force model. The curvature effects of tool path on chip thickness as well as entry and exit angles are analyzed, and the cutting force model of linear milling process is then corrected to fit circular end milling processes. Instantaneous cutting forces during circular end milling process are predicted according to the proposed model. The deduced cutting force model can be used for both linear and circular end milling processes. Finally, circular end milling experiments with constant and variable radial depth were carried out to verify the availability of the proposed method. Experiment results show that measured results and simulated results corresponds well with each other.展开更多
Electrolyte jet machining(EJM)is a promising method for shaping titanium alloys due to its lack of tool wear,thermal and residual stress,and cracks and burrs.Recently,macro-EJM has attracted increasing attention for i...Electrolyte jet machining(EJM)is a promising method for shaping titanium alloys due to its lack of tool wear,thermal and residual stress,and cracks and burrs.Recently,macro-EJM has attracted increasing attention for its high efficiency in machining wide grooves or planes.However,macro-EJM generates large amounts of electrolytic products,thereby increasing the difficulty of rapid product removal with a standard tool and reducing the surface quality.Therefore,for enhanced product transport,a novel tool with a back inclined end face was proposed for macroEJM of TC4 titanium alloy.For comparison,also proposed were ones with a standard flat end face,a front inclined end face,and both front and back inclined end faces.The flow field distributions of all proposed tools were simulated numerically,and experiments were also conducted to validate the simulation results.The results show that one with a 5°back inclined end face can decrease the lowvelocity flow zone in the machining area and increase the high-velocity flow zone at the back end of tool,thereby promoting rapid product removal.A relatively smooth bright-white groove surface was obtained.The same tool also resulted in the highest machining depth and material removal rate among the tested ones.In addition,rapid product removal was beneficial to the subsequent processing.Because of its rapid product removal,the machining depth and material removal rate during deep groove machining using the tool with a 5°back inclined end face were respectively 7%and14%higher than those produced using a standard one.Moreover,the lowest bottom height difference of 0.027 mm can be obtained when the step-over value was 8.2 mm,and a plane with a depth of0.285 mm and a bottom height difference of 0.03 mm was fabricated using the tool with a 5°back inclined end face.展开更多
基金co-supported by Open National Natural Science Foundation of China(No.51005183)National Science and Technology Major Project(No.2011ZX04016031)China Postdoctoral Science Foundation(No.2012M521804)
文摘A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cutting conditions, especially for circular milling process. This paper presents an improved cutting force model for circular end milling process based on the typical linear milling force model. The curvature effects of tool path on chip thickness as well as entry and exit angles are analyzed, and the cutting force model of linear milling process is then corrected to fit circular end milling processes. Instantaneous cutting forces during circular end milling process are predicted according to the proposed model. The deduced cutting force model can be used for both linear and circular end milling processes. Finally, circular end milling experiments with constant and variable radial depth were carried out to verify the availability of the proposed method. Experiment results show that measured results and simulated results corresponds well with each other.
基金supported by the National Natural Science Foundation of China(No.91860208)the National Natural Science Foundation of China for Creative Research Groups(No.51921003)。
文摘Electrolyte jet machining(EJM)is a promising method for shaping titanium alloys due to its lack of tool wear,thermal and residual stress,and cracks and burrs.Recently,macro-EJM has attracted increasing attention for its high efficiency in machining wide grooves or planes.However,macro-EJM generates large amounts of electrolytic products,thereby increasing the difficulty of rapid product removal with a standard tool and reducing the surface quality.Therefore,for enhanced product transport,a novel tool with a back inclined end face was proposed for macroEJM of TC4 titanium alloy.For comparison,also proposed were ones with a standard flat end face,a front inclined end face,and both front and back inclined end faces.The flow field distributions of all proposed tools were simulated numerically,and experiments were also conducted to validate the simulation results.The results show that one with a 5°back inclined end face can decrease the lowvelocity flow zone in the machining area and increase the high-velocity flow zone at the back end of tool,thereby promoting rapid product removal.A relatively smooth bright-white groove surface was obtained.The same tool also resulted in the highest machining depth and material removal rate among the tested ones.In addition,rapid product removal was beneficial to the subsequent processing.Because of its rapid product removal,the machining depth and material removal rate during deep groove machining using the tool with a 5°back inclined end face were respectively 7%and14%higher than those produced using a standard one.Moreover,the lowest bottom height difference of 0.027 mm can be obtained when the step-over value was 8.2 mm,and a plane with a depth of0.285 mm and a bottom height difference of 0.03 mm was fabricated using the tool with a 5°back inclined end face.
