Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate(nano-CaCO3) surface modified with γ-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl ...Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate(nano-CaCO3) surface modified with γ-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl methacrylate) (PMMA)/nano-CaCO3 composite. The reaction between nano-CaCO3 and MPTMS, and the grafting of PMMA onto nano-CaCO3 were confirmed by infrared spectrum. The grafting ratio and grafting efficiency of PMMA on nano-CaCO3 modified with MPTMS were much higher than that on nano-CaCO3 modified with stearic acid. The grafting ratio of PMMA increased as the weight ratio between MMA and nano-CaCO3 increased, while the grafting efficiency of PMMA decreased. Transmission electron micrograph showed that nano-CaCO3 covered with PMMA was formed by in-situ emulsion polymerization.展开更多
The particle size distribution of polymer always develops in emulsion polymerization systems,and certain key phenomena/mechanisms as well as properties of the final product are significantly affected by this distribut...The particle size distribution of polymer always develops in emulsion polymerization systems,and certain key phenomena/mechanisms as well as properties of the final product are significantly affected by this distribution.This review mainly focuses on the measurement methods of particle size distribution rather than average particle size during the emulsion polymerization process,including the existing off-line,on-line,and in-line measurement methods.Moreover,the principle,resolution,performance,advantages,and drawbacks of various methods for evaluating particle size distribution are contrasted and illustrated.Besides,several possible development directions or solutions of the in-line measurement technology are explored.展开更多
Suspended emulsion polymerization was used to prepare poly(vinyl chloride) (PVC) resin. Fine PVC particleswere formed at low polymerization conversions. The amount of fine panicles decreases as conversion increases an...Suspended emulsion polymerization was used to prepare poly(vinyl chloride) (PVC) resin. Fine PVC particleswere formed at low polymerization conversions. The amount of fine panicles decreases as conversion increases anddisappears at conversions greater than 30%. Scanning electron micrographs show that PVC grains are composed of looselycoalesced primary particles, especially for PVC resins prepared in the presence of poly(vinyl alcohol) dispersant. The size ofprimary particles increases and porosity decreases with the increase of conversion. In view of the particle features of PVCresin, a particle formation mechanism including the formation of primary particles and grains is proposed. The formationprocess of primary particles includes the formation of particle nuclei, coalescence of particle nuclei to form primary particles,and growth of primary particles. PVC grains are formed by the coagulation of primary particles. The loose coalescence ofprimary particles is caused by the colloidal stability of primary particles and the low swelling degree of vinyl chloride in the primary particles.展开更多
Suspended emulsion polymerization of vinyl chloride was carried out in a 5 L autoclave. The influence of agitation, polymerization conversion, dispersant and surfactant on the average particle size (PS) and particle s...Suspended emulsion polymerization of vinyl chloride was carried out in a 5 L autoclave. The influence of agitation, polymerization conversion, dispersant and surfactant on the average particle size (PS) and particle size distribution (PSD), particle morphology and porosity of polyvinyl chloride (PVC) resin was investigated. It showed that the agitator had great influence on the smooth operation of polymerization, PS and PSD. The PS increased and PSD became narrow as polymerization conversion became high. The porosity decreased with the increase of conversion. A convenient choice of additives, both dispersants and non-ionic surfactants, allows one to adjust PS and PSD. The PS decreased with the addition of polyvinyl alcohol or hydroxypropyl methylcellulose dispersants,and increased with the addition of Span surfactants. The addition of dispersants or surfactants also affected the morphology and porosity of resin, and PVC resin with looser agglomeration and homogeneous distribution of primary particles was prepared.展开更多
Poly（St-co-BuA）/silica nanocomposite latexes were synthesized via conventional emulsion polymerization in the presence of 3-（trimethoxysilyl）propyl methacrylate modified colloidal nano-silica. The effects of surfa...Poly（St-co-BuA）/silica nanocomposite latexes were synthesized via conventional emulsion polymerization in the presence of 3-（trimethoxysilyl）propyl methacrylate modified colloidal nano-silica. The effects of surface property, particle size and content of colloidal nano-silica as well as the concentrations of monomer and surfactant on the morphology of nanocomposite latex particles were investigated by transmission electron microscope （TEM） and scanning electron microscope （SEM） in detail. Various interesting morphologies such as grape-like, Chinese gooseberry-like, pomegranate-like and normal core-shell structures were observed. Droplet nucleation mechanism competing with micelle nucleation mechanism was proposed to explain the morphological evolution of the nanocomposite particles.展开更多
Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at dif...Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at different OFA weight ratios （2.0 wt%, 5.0 wt%, 10.0 wt%, 15.0 wt% and 20.0 wt%） in the presence of dodecylbenzenesulfonic acid as dopant and emulsifier. A polymerization procedure was supposed. The electrical conductivities of the composites were tested by the four-probe technique. The chemical structure and crystallinity of the composites were confirmed by FT-IR and X-ray diffraction, respectively. Morphologies of FA, OFA and the composites were observed by SEM. The element analysis was performed by energy dispersive spectrometry. The thermal stability of the composites was analyzed by TGA. The results showed that the electrical conductivity of the composites decreased with increasing the feed weight ratio of OFA, and the lowest value was 0.62 S/cm. HDTMAB and PAn were just adsorbed on the surface of FA and OFA, respectively according to the physical adsorption without destroying the crystalline structure of FA or OFA. The surface became smoother after organification of FA by using HDTMAB, and its content on FA surfaces was about 26.9 wt%. The core/shell structure of the composite was observed by SEM analysis. The composites showed a higher thermal stability than pure PAn by introduction of OFA into this polymerization system, the heat stability of PAn was increased by decreasing 31.8 wt% of weight loss after introducing 20 wt% of OFA.展开更多
The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The ...The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization. (c) 2007 Cheng You Kan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
Poly(styrene-co-glycidyl methacrylate) latex microspheres with uniform size and high-density epoxy groups on the surface were prepared by soap-free emulsion polymerization with batch wise operation mode in the presenc...Poly(styrene-co-glycidyl methacrylate) latex microspheres with uniform size and high-density epoxy groups on the surface were prepared by soap-free emulsion polymerization with batch wise operation mode in the presence of 2.2′- azobis(2-methylpropionamidine) dihydrochloride as an initiator.The kinetics of soap-free emulsion polymerization and the effects of polymerization factors were examined.In addition,the optimum polymerization conditions of poly(styrene-co- glycidyl methacrylate) latex microspheres for...展开更多
Submicron-sized peanut-shaped poly（methyl methacrylate）/polystyrene （PMMA/PS） particles were successfully synthesized by seeded soap-free emulsion polymerization of styrene on the spherical crosslinked PMMA seed p...Submicron-sized peanut-shaped poly（methyl methacrylate）/polystyrene （PMMA/PS） particles were successfully synthesized by seeded soap-free emulsion polymerization of styrene on the spherical crosslinked PMMA seed particles. The obtained peanut- shaped particles showed a novel internal morphology： PS phase formed one domain which linked to the other domain having PMMA core encased by PS shell.展开更多
Polymerization-induced self-assembly(PISA) is an efficient and versatile method to afford polymeric nano-objects with polymorphic morphologies. Compared to dispersion PISA syntheses based on soluble monomers, the vast...Polymerization-induced self-assembly(PISA) is an efficient and versatile method to afford polymeric nano-objects with polymorphic morphologies. Compared to dispersion PISA syntheses based on soluble monomers, the vast majority of emulsion PISA formulations using insoluble monomers leads to kinetically-trapped spheres. Herein, we present aqueous emulsion PISA formulations generating worms and vesicles besides spheres. Two monomers with different butyl groups, n-butyl(n BHMA) and tert-butyl(t BHMA) α-hydroxymethyl acrylate, and thus possessing different water solubilities were synthesized via Baylis-Hillman reaction. Photoinitiated aqueous emulsion polymerizations of n BHMA and t BHMA employing poly(ethylene glycol) macromolecular chain transfer agents(macro-CTAs, PEG45-CTA, and PEG113-CTA) at 40 °C were systematically investigated to evaluate the effect of monomer structure and solubility on the morphology of the generated block copolymer nano-objects. Higher order morphologies including worms and vesicles were readily accessed for t BHMA, which has a higher water solubility than that of n BHMA. This study proves that plasticization of the core-forming block by water plays a key role in enhancing chain mobility required for morphological transition in emulsion PISA.展开更多
One of the major challenges associated with fuel cells is the design of highly efficient electrocatalysts to reduce the high overpotential of the oxygen reduction reaction (ORR). Here we report Polyaniline (PANI) base...One of the major challenges associated with fuel cells is the design of highly efficient electrocatalysts to reduce the high overpotential of the oxygen reduction reaction (ORR). Here we report Polyaniline (PANI) based micro/nanomaterials with or without transition metals, prepared by the emulsion polymerization and subsequent heat treatment. PANI microspheres with the diameter of about 0.7 mu m have been prepared in basic (NH3 solution) condition, using two different types of surfactant (CTAB, SDS) as the stabilizer, ammonium persulphate (APS) as oxidant with aniline/surfactants molar ratio at 1/1 under the hydrothermal treatment. PANI nanorods, Fe-PANI, and Fe-Co-PANI have been synthesized in acidic (HCI) medium with aniline/surfactants molar ratio at 1/2 and polymerization carried out without stirring for 24 h. Products mainly Fe-Co-PANI have shown high current density with increasing sweep rate and excellent specific capacitance 1753 F/g at the scan rate of 1 mV/s. Additionally, it has shown high thermal stability by thermogravimetric analysis (TGA). Fe-PANI has been investigated for excellent performance toward ORR with four electron selectivity in the basic electrolyte. The PANI-based catalysts from emulsion polymerization demonstrate that the method is valuable for making non-precious metal heterogeneous electrocatalysts for ORR or energy storage and conversion technology. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.展开更多
Stimulus-responsive vesicles have broad applications in a variety of areas. Herein, oxidation-responsive framboidal triblock copolymer vesicles are prepared by photoinitiated RAFT seeded emulsion polymerization of a t...Stimulus-responsive vesicles have broad applications in a variety of areas. Herein, oxidation-responsive framboidal triblock copolymer vesicles are prepared by photoinitiated RAFT seeded emulsion polymerization of a thioether-functionalized monomer using diblock copolymer vesicles as seeds. The obtained framboidal vesicles can transform into worms or spheres in the presence of reactive oxygen species,which can be further used for controlled release of cargos(e.g., silica nanoparticles).展开更多
Photoenzymatic reversible addition-fragmenatation chain transfer(RAFT)emulsion polymerization,surfactant-free or ab initio,of various monomers is reported with oxygen toleranee.In surfactant-free emulsion polymerizato...Photoenzymatic reversible addition-fragmenatation chain transfer(RAFT)emulsion polymerization,surfactant-free or ab initio,of various monomers is reported with oxygen toleranee.In surfactant-free emulsion polymerizatoin,poly(N,N-dimethylacrylamide)s were used as stabilizer blocks for emulsion polymerization of methyl acrylate,n-butyl acrylate and styrene,producing well-defined amphiphilic block copolymers,including those with an ultrahigh molecular weight,at quantitative conversions.The controlled character of surfactant-free emulsion polymerization was confirmed by kinetic studies,chain extension studies and GPC analyses.Temporal control was demonstrated by light ON/OFF experiments.In ab initio emulsion polymerization of methyl acrylate and methyl methacrylate,low-dispersity hydrophobic polymers were synthesized with predictable molecular weights.This study extends the monomer scope suitable for photoenzymatic RAFT polymerization from hydrophilic to hydrophobic monomers and demonstrates that oxygen-toleranee can be equally achieved for emulsion polymerization with excellent RAFT control.展开更多
Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free em...Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.展开更多
Micron-sized nonspherical polymer particles having different morphologies were synthesized by seeded soap-free emulsion polymerization of styrene （St） and ethyleneglycol dimethacrylate （EGDMA, used as a crosslinker...Micron-sized nonspherical polymer particles having different morphologies were synthesized by seeded soap-free emulsion polymerization of styrene （St） and ethyleneglycol dimethacrylate （EGDMA, used as a crosslinker） on spherical, linear polystyrene （PS） seed particles. The morphology of the resulting PS/poly（St-co-EGDMA） particles was dependent on the crosslinker concentration and polymerization temperature.展开更多
Bowl-like poly (styrene-co-glycidyl methacrylate) was synthesized by swollen seeded emulsion polymerization. The polymerization was carried out in PS seed emulsion swollen by toluene, whereby the bowl-like particles f...Bowl-like poly (styrene-co-glycidyl methacrylate) was synthesized by swollen seeded emulsion polymerization. The polymerization was carried out in PS seed emulsion swollen by toluene, whereby the bowl-like particles formed at last. The shape was observed by SEM. These particles became ball-like when swollen by toluene, observed by optical microscope, and the release behavior of solvent from them was examined.展开更多
The structure and properties of functional nanoparticles are important for stabilizing Pickering emulsion polymerization.Recently,cellulose nanocrystals(CNCs)are increasingly favored as a bio-based stabilizer for Pick...The structure and properties of functional nanoparticles are important for stabilizing Pickering emulsion polymerization.Recently,cellulose nanocrystals(CNCs)are increasingly favored as a bio-based stabilizer for Pickering emulsions.In this study,we reported a novel functionalized polyphosphoester-grafted CNCs for the stabilization of oil-in-water Pickering emulsions and the emulsion polymerization of styrene.First,polyphosphoester containing an amino group at one end of the chain,abbreviated as PBYP-NH2,was prepared by ring-opening polymerization(ROP)and hydrolysis reaction,wherein PBYP represents poly[2-(but-3-yn-1-yloxy)-2-oxo-1,3,2-dioxaphospholane].Subsequently,CNC-COOH was obtained via 2,2,6,6-tetramethylpiperidine-1-oxyl(TEMPO)oxidation of CNCs.The functionalized nanocrystals CNC-PBYP-COOH with carboxyl groups and polyphosphoester on the surface were obtained by the amidation reaction of PBYP-NH2 with CNC-COOH.Finally,we used CNC-PBYP-COOH as sole particle emulsifiers to stabilize styrene-in-water Pickering emulsions and studied its effects on the emulsions in details by using dynamic light scattering(DLS).The results indicated that the properties of these emulsions depended on the concentration of hydrophobically modified CNCs,volume ratios of oil to water,and pH values.The modified CNCs had higher ability to stabilize the styrene-in-water emulsions relative to the unmodified CNCs,and a stable oil-in-water(o/w)Pickering emulsion with diameter of hundreds of nanometers could be obtained.The resulting emulsions could be polymerized to yield nanosized latexes.The polyphosphoester-modified CNCs as green particle emulsifiers can efficiently stabilize nanoemulsions and latexes,which would promote the development of novel environmentally friendly materials.展开更多
Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a referen...Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.展开更多
Styrene emulsion polymerization using an alkyl-9-BBN,synthesized by reacting 9-BBN(9-borabicyclo-[3.3.1]-nonane)and styrene,in an aqueous sodium dodecyl sulfate(SDS)solution was studied.Ultra-high-molecular-weight(〉1...Styrene emulsion polymerization using an alkyl-9-BBN,synthesized by reacting 9-BBN(9-borabicyclo-[3.3.1]-nonane)and styrene,in an aqueous sodium dodecyl sulfate(SDS)solution was studied.Ultra-high-molecular-weight(〉1.0×10^(7))polystyrene was synthesized using a radical initiator formed through the aerobic oxidation of this alkyl-9-BBN in a high yield(〉80%).The kinetics of this emulsion polymerization of styrene with the alkyl-9-BBN was investigated.We confirmed that in the initial stage of the polymerization,the initial reaction rate followed first-order kinetics.The activation energy for this emulsion polymerization of styrene was approximately 56.2 kJ/mol.展开更多
Soap-free poly（methyl methacrylate-ethyl acrylate-methacrylic acid） latex particles with narrow size distribution were synthesized by seeded emulsion polymerization, and the porous particles were created by a stepwi...Soap-free poly（methyl methacrylate-ethyl acrylate-methacrylic acid） latex particles with narrow size distribution were synthesized by seeded emulsion polymerization, and the porous particles were created by a stepwise alkali/acid treatment method. Effects of acid treatment conditions on the particle morphology were investigated. Results show that one to three pores were formed inside most of particles after post-treatment. At pH 7.0, when the treatment temperature was lower than 70℃, the size of particles and the volume of pores remained almost unchanged, and these two values increased significantly when the temperature was higher than 70℃. Both the particle size and the pore volume decreased with the increase of initial pH value and treatment time in the acid treatment. As the pH was below 4.0 and the treatment time was longer than 180 min, the particles shrunk in size.展开更多
文摘Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate(nano-CaCO3) surface modified with γ-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl methacrylate) (PMMA)/nano-CaCO3 composite. The reaction between nano-CaCO3 and MPTMS, and the grafting of PMMA onto nano-CaCO3 were confirmed by infrared spectrum. The grafting ratio and grafting efficiency of PMMA on nano-CaCO3 modified with MPTMS were much higher than that on nano-CaCO3 modified with stearic acid. The grafting ratio of PMMA increased as the weight ratio between MMA and nano-CaCO3 increased, while the grafting efficiency of PMMA decreased. Transmission electron micrograph showed that nano-CaCO3 covered with PMMA was formed by in-situ emulsion polymerization.
基金The National Key Research and Development Program(2020YFA0906804)the National Natural Science Foundation of China(22078325,22035007,91934301)+1 种基金the NSFC-EU project(31961133018)the Special Project of Strategic Leading Science and Technology,CAS(XDC06010302)are gratefully acknowledged.
文摘The particle size distribution of polymer always develops in emulsion polymerization systems,and certain key phenomena/mechanisms as well as properties of the final product are significantly affected by this distribution.This review mainly focuses on the measurement methods of particle size distribution rather than average particle size during the emulsion polymerization process,including the existing off-line,on-line,and in-line measurement methods.Moreover,the principle,resolution,performance,advantages,and drawbacks of various methods for evaluating particle size distribution are contrasted and illustrated.Besides,several possible development directions or solutions of the in-line measurement technology are explored.
基金The project is supported by the National Natural Science Foundation of China (No. 29906009)
文摘Suspended emulsion polymerization was used to prepare poly(vinyl chloride) (PVC) resin. Fine PVC particleswere formed at low polymerization conversions. The amount of fine panicles decreases as conversion increases anddisappears at conversions greater than 30%. Scanning electron micrographs show that PVC grains are composed of looselycoalesced primary particles, especially for PVC resins prepared in the presence of poly(vinyl alcohol) dispersant. The size ofprimary particles increases and porosity decreases with the increase of conversion. In view of the particle features of PVCresin, a particle formation mechanism including the formation of primary particles and grains is proposed. The formationprocess of primary particles includes the formation of particle nuclei, coalescence of particle nuclei to form primary particles,and growth of primary particles. PVC grains are formed by the coagulation of primary particles. The loose coalescence ofprimary particles is caused by the colloidal stability of primary particles and the low swelling degree of vinyl chloride in the primary particles.
基金Supported by the National Natural Science Foundation of China (No. 29906009).
文摘Suspended emulsion polymerization of vinyl chloride was carried out in a 5 L autoclave. The influence of agitation, polymerization conversion, dispersant and surfactant on the average particle size (PS) and particle size distribution (PSD), particle morphology and porosity of polyvinyl chloride (PVC) resin was investigated. It showed that the agitator had great influence on the smooth operation of polymerization, PS and PSD. The PS increased and PSD became narrow as polymerization conversion became high. The porosity decreased with the increase of conversion. A convenient choice of additives, both dispersants and non-ionic surfactants, allows one to adjust PS and PSD. The PS decreased with the addition of polyvinyl alcohol or hydroxypropyl methylcellulose dispersants,and increased with the addition of Span surfactants. The addition of dispersants or surfactants also affected the morphology and porosity of resin, and PVC resin with looser agglomeration and homogeneous distribution of primary particles was prepared.
基金This research was financially supported by the Key Project of China Educational Ministry (No. 103064)the Doctoral Foundation of University (No. 20020246031)
文摘Poly（St-co-BuA）/silica nanocomposite latexes were synthesized via conventional emulsion polymerization in the presence of 3-（trimethoxysilyl）propyl methacrylate modified colloidal nano-silica. The effects of surface property, particle size and content of colloidal nano-silica as well as the concentrations of monomer and surfactant on the morphology of nanocomposite latex particles were investigated by transmission electron microscope （TEM） and scanning electron microscope （SEM） in detail. Various interesting morphologies such as grape-like, Chinese gooseberry-like, pomegranate-like and normal core-shell structures were observed. Droplet nucleation mechanism competing with micelle nucleation mechanism was proposed to explain the morphological evolution of the nanocomposite particles.
基金supported by the Shaanxi Provincial Education Department(No.09JK528) and Program of Shaanxi Key Subject
文摘Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at different OFA weight ratios （2.0 wt%, 5.0 wt%, 10.0 wt%, 15.0 wt% and 20.0 wt%） in the presence of dodecylbenzenesulfonic acid as dopant and emulsifier. A polymerization procedure was supposed. The electrical conductivities of the composites were tested by the four-probe technique. The chemical structure and crystallinity of the composites were confirmed by FT-IR and X-ray diffraction, respectively. Morphologies of FA, OFA and the composites were observed by SEM. The element analysis was performed by energy dispersive spectrometry. The thermal stability of the composites was analyzed by TGA. The results showed that the electrical conductivity of the composites decreased with increasing the feed weight ratio of OFA, and the lowest value was 0.62 S/cm. HDTMAB and PAn were just adsorbed on the surface of FA and OFA, respectively according to the physical adsorption without destroying the crystalline structure of FA or OFA. The surface became smoother after organification of FA by using HDTMAB, and its content on FA surfaces was about 26.9 wt%. The core/shell structure of the composite was observed by SEM analysis. The composites showed a higher thermal stability than pure PAn by introduction of OFA into this polymerization system, the heat stability of PAn was increased by decreasing 31.8 wt% of weight loss after introducing 20 wt% of OFA.
文摘The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization. (c) 2007 Cheng You Kan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
基金supported by the State Key Laboratory of Chemical Engineering of Zhejiang Universitythe financial support from the National Natural Science Foundation of China (No.20676113).
文摘Poly(styrene-co-glycidyl methacrylate) latex microspheres with uniform size and high-density epoxy groups on the surface were prepared by soap-free emulsion polymerization with batch wise operation mode in the presence of 2.2′- azobis(2-methylpropionamidine) dihydrochloride as an initiator.The kinetics of soap-free emulsion polymerization and the effects of polymerization factors were examined.In addition,the optimum polymerization conditions of poly(styrene-co- glycidyl methacrylate) latex microspheres for...
基金supported by National Natural Science Foundation of China(No.50943028)Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry
文摘Submicron-sized peanut-shaped poly（methyl methacrylate）/polystyrene （PMMA/PS） particles were successfully synthesized by seeded soap-free emulsion polymerization of styrene on the spherical crosslinked PMMA seed particles. The obtained peanut- shaped particles showed a novel internal morphology： PS phase formed one domain which linked to the other domain having PMMA core encased by PS shell.
基金financially supported by the National Natural Science Foundation of China (No. 21674059)
文摘Polymerization-induced self-assembly(PISA) is an efficient and versatile method to afford polymeric nano-objects with polymorphic morphologies. Compared to dispersion PISA syntheses based on soluble monomers, the vast majority of emulsion PISA formulations using insoluble monomers leads to kinetically-trapped spheres. Herein, we present aqueous emulsion PISA formulations generating worms and vesicles besides spheres. Two monomers with different butyl groups, n-butyl(n BHMA) and tert-butyl(t BHMA) α-hydroxymethyl acrylate, and thus possessing different water solubilities were synthesized via Baylis-Hillman reaction. Photoinitiated aqueous emulsion polymerizations of n BHMA and t BHMA employing poly(ethylene glycol) macromolecular chain transfer agents(macro-CTAs, PEG45-CTA, and PEG113-CTA) at 40 °C were systematically investigated to evaluate the effect of monomer structure and solubility on the morphology of the generated block copolymer nano-objects. Higher order morphologies including worms and vesicles were readily accessed for t BHMA, which has a higher water solubility than that of n BHMA. This study proves that plasticization of the core-forming block by water plays a key role in enhancing chain mobility required for morphological transition in emulsion PISA.
基金support by the National Natural Science Foundation of China(Grant no.21373042)
文摘One of the major challenges associated with fuel cells is the design of highly efficient electrocatalysts to reduce the high overpotential of the oxygen reduction reaction (ORR). Here we report Polyaniline (PANI) based micro/nanomaterials with or without transition metals, prepared by the emulsion polymerization and subsequent heat treatment. PANI microspheres with the diameter of about 0.7 mu m have been prepared in basic (NH3 solution) condition, using two different types of surfactant (CTAB, SDS) as the stabilizer, ammonium persulphate (APS) as oxidant with aniline/surfactants molar ratio at 1/1 under the hydrothermal treatment. PANI nanorods, Fe-PANI, and Fe-Co-PANI have been synthesized in acidic (HCI) medium with aniline/surfactants molar ratio at 1/2 and polymerization carried out without stirring for 24 h. Products mainly Fe-Co-PANI have shown high current density with increasing sweep rate and excellent specific capacitance 1753 F/g at the scan rate of 1 mV/s. Additionally, it has shown high thermal stability by thermogravimetric analysis (TGA). Fe-PANI has been investigated for excellent performance toward ORR with four electron selectivity in the basic electrolyte. The PANI-based catalysts from emulsion polymerization demonstrate that the method is valuable for making non-precious metal heterogeneous electrocatalysts for ORR or energy storage and conversion technology. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
基金support from the Science and Technology Program of Guangzhou(No.202102020631)the National Natural Science Foundation of China(Nos.22171055 and 21971047)+1 种基金Innovation Project of Education Department in Guangdong(No.2018KTSCX053)support from Guangdong Special Support Program(No.2017TX04N371)。
文摘Stimulus-responsive vesicles have broad applications in a variety of areas. Herein, oxidation-responsive framboidal triblock copolymer vesicles are prepared by photoinitiated RAFT seeded emulsion polymerization of a thioether-functionalized monomer using diblock copolymer vesicles as seeds. The obtained framboidal vesicles can transform into worms or spheres in the presence of reactive oxygen species,which can be further used for controlled release of cargos(e.g., silica nanoparticles).
基金We are thankful for financial support from the National Natural Science Foundation of China(No.21871175)the Fundamental Research Funds for the Central Universities.
文摘Photoenzymatic reversible addition-fragmenatation chain transfer(RAFT)emulsion polymerization,surfactant-free or ab initio,of various monomers is reported with oxygen toleranee.In surfactant-free emulsion polymerizatoin,poly(N,N-dimethylacrylamide)s were used as stabilizer blocks for emulsion polymerization of methyl acrylate,n-butyl acrylate and styrene,producing well-defined amphiphilic block copolymers,including those with an ultrahigh molecular weight,at quantitative conversions.The controlled character of surfactant-free emulsion polymerization was confirmed by kinetic studies,chain extension studies and GPC analyses.Temporal control was demonstrated by light ON/OFF experiments.In ab initio emulsion polymerization of methyl acrylate and methyl methacrylate,low-dispersity hydrophobic polymers were synthesized with predictable molecular weights.This study extends the monomer scope suitable for photoenzymatic RAFT polymerization from hydrophilic to hydrophobic monomers and demonstrates that oxygen-toleranee can be equally achieved for emulsion polymerization with excellent RAFT control.
基金Funded by the Jiangsu Provincial Creative Fund for Scientific and Tech-nical Small and Medium-size Enterprise
文摘Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.
基金partially supported by the National Natural Science Foundation of China(No.50943028)Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry
文摘Micron-sized nonspherical polymer particles having different morphologies were synthesized by seeded soap-free emulsion polymerization of styrene （St） and ethyleneglycol dimethacrylate （EGDMA, used as a crosslinker） on spherical, linear polystyrene （PS） seed particles. The morphology of the resulting PS/poly（St-co-EGDMA） particles was dependent on the crosslinker concentration and polymerization temperature.
文摘Bowl-like poly (styrene-co-glycidyl methacrylate) was synthesized by swollen seeded emulsion polymerization. The polymerization was carried out in PS seed emulsion swollen by toluene, whereby the bowl-like particles formed at last. The shape was observed by SEM. These particles became ball-like when swollen by toluene, observed by optical microscope, and the release behavior of solvent from them was examined.
基金the National Natural Science Foundation of China(Nos.21975169 and 21374066)the Major Program of the Natural Science Project of Jiangsu Higher Education Institutions(No.15KJA150007)+2 种基金the Natural Science Foundation of Jiangsu Province(No.BK20171212)a Project Funded by the Priority Academic Program Development(PAPD)of Jiangsu Higher Education InstitutionsSoochow-Waterloo University Joint Project for Nanotechnology from Suzhou Industrial Park.
文摘The structure and properties of functional nanoparticles are important for stabilizing Pickering emulsion polymerization.Recently,cellulose nanocrystals(CNCs)are increasingly favored as a bio-based stabilizer for Pickering emulsions.In this study,we reported a novel functionalized polyphosphoester-grafted CNCs for the stabilization of oil-in-water Pickering emulsions and the emulsion polymerization of styrene.First,polyphosphoester containing an amino group at one end of the chain,abbreviated as PBYP-NH2,was prepared by ring-opening polymerization(ROP)and hydrolysis reaction,wherein PBYP represents poly[2-(but-3-yn-1-yloxy)-2-oxo-1,3,2-dioxaphospholane].Subsequently,CNC-COOH was obtained via 2,2,6,6-tetramethylpiperidine-1-oxyl(TEMPO)oxidation of CNCs.The functionalized nanocrystals CNC-PBYP-COOH with carboxyl groups and polyphosphoester on the surface were obtained by the amidation reaction of PBYP-NH2 with CNC-COOH.Finally,we used CNC-PBYP-COOH as sole particle emulsifiers to stabilize styrene-in-water Pickering emulsions and studied its effects on the emulsions in details by using dynamic light scattering(DLS).The results indicated that the properties of these emulsions depended on the concentration of hydrophobically modified CNCs,volume ratios of oil to water,and pH values.The modified CNCs had higher ability to stabilize the styrene-in-water emulsions relative to the unmodified CNCs,and a stable oil-in-water(o/w)Pickering emulsion with diameter of hundreds of nanometers could be obtained.The resulting emulsions could be polymerized to yield nanosized latexes.The polyphosphoester-modified CNCs as green particle emulsifiers can efficiently stabilize nanoemulsions and latexes,which would promote the development of novel environmentally friendly materials.
基金Funded by Ministry of Education (No.2006-KL-008),and Qingxin Hanerchem Chemical Technology Co,Ltd.
文摘Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.
文摘Styrene emulsion polymerization using an alkyl-9-BBN,synthesized by reacting 9-BBN(9-borabicyclo-[3.3.1]-nonane)and styrene,in an aqueous sodium dodecyl sulfate(SDS)solution was studied.Ultra-high-molecular-weight(〉1.0×10^(7))polystyrene was synthesized using a radical initiator formed through the aerobic oxidation of this alkyl-9-BBN in a high yield(〉80%).The kinetics of this emulsion polymerization of styrene with the alkyl-9-BBN was investigated.We confirmed that in the initial stage of the polymerization,the initial reaction rate followed first-order kinetics.The activation energy for this emulsion polymerization of styrene was approximately 56.2 kJ/mol.
基金The research was supported by the National 863 Project of China(No.2001AA242041).
文摘Soap-free poly（methyl methacrylate-ethyl acrylate-methacrylic acid） latex particles with narrow size distribution were synthesized by seeded emulsion polymerization, and the porous particles were created by a stepwise alkali/acid treatment method. Effects of acid treatment conditions on the particle morphology were investigated. Results show that one to three pores were formed inside most of particles after post-treatment. At pH 7.0, when the treatment temperature was lower than 70℃, the size of particles and the volume of pores remained almost unchanged, and these two values increased significantly when the temperature was higher than 70℃. Both the particle size and the pore volume decreased with the increase of initial pH value and treatment time in the acid treatment. As the pH was below 4.0 and the treatment time was longer than 180 min, the particles shrunk in size.
