This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a ...This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a dry cement powder core,a saturated clay middle layer,and a dry sand upper layer.The test injects H_(2)O_(2)solution into the cement core to produce new pore-gas.The model test includes three identical H_(2)O_(2)injections.The small mass of generated oxygen gas(0.07%of slope soil mass and landslide body)from the first injection can build sufficient pore-gas pressure to cause soil upheaval and slide.Meanwhile,despite the first injection causing leak paths in the clay layer,the generated small mass of gas from the second and third injections can further trigger the landslide.A dynamic theoretical analysis of the slope failure is carried out and the required minimum pore-gas pressure for the landslide is calculated.The mass and pressure of generated gas in the model test are also estimated based on the calibration test for oxygen generation from H_(2)O_(2)solution in cement powder.The results indicate that the minimum mass of the generated gas for triggering the landslide is 2 ppm to 0.07%of the landslide body.Furthermore,the small mass of gas can provide sufficient pressure to cause soil upheaval and soil sliding in dynamic analysis.展开更多
As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminat...As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminated shell element is used to establish the finite element model(FEM)of a flexibly coated casing system.Using the shell element,the blade is modeled,and the surface stress of the blade is calculated.The stress-solving method of the blade is validated through comparisons with the measured time-domain waveform of the stress.Then,a dynamic model of a blade-flexibly coated casing system with rubbing is proposed,accounting for the time-varying mass and stiffness of the casing caused by coating wear.The effects of the proposed flexible casing model are compared with those of a rigid casing model,and the stress changes induced by rubbing are investigated.The results show that the natural characteristics of the coated casing decrease due to the coating wear.The flexibly coated casing model is found to be more suitable for studying casing vibration.Additionally,the stress changes caused by rubbing are slight,and the change in the stress maximum is approximately 5%under the influence of the abrasive coating.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can b...PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.展开更多
There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed...There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed.In this paper,according to hysteresis loops of the clamp obtained from experimental test,the simplified bilinear stiffness and damping model is proposed.Then the Finite Element(FE)model of L-type pipeline system with clamps is established using Timoshenko beam theory in combination with aforementioned stiffness-damping model.Both hammering and shaker tests verify the FE model via the comparisons of natural frequencies and vibration responses.The results show that the maximum errors of natural frequencies and vibration responses are about 8.31%and 17.6%,respectively.The proposed model can simulate the dynamic characteristics of the L-type pipeline system with clamps well,which is helpful to provide some guidance for the early design stage of pipeline in aero-engine.展开更多
For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be ...For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.展开更多
Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batc...Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batch distillation is proposed in this work,in which the changes in column holdup and liquid flow rate during the filling of the drum,and the consequent change in valid number of theoretical plates are considered.The effect of drum holdup on operation time is investigated and the optimal drum holdup is obtained from the simulation.The dynamic modeling is compared to the conventional modeling without consideration of change in liquid flow rate. The experimental result shows that the present modeling is more reliable and more accurate,especially for the column with large liquid holdup.展开更多
The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and th...The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.展开更多
In order to better study the dynamic characteristics and the control strategy of parafoil systems,considering the effect of flap deflection as the control mechanism and regarding the parafoil and the payload as a rigi...In order to better study the dynamic characteristics and the control strategy of parafoil systems,considering the effect of flap deflection as the control mechanism and regarding the parafoil and the payload as a rigid body,a six degrees-of-freedom(DOF)dynamic model of a parafoil system including three DOF for translational motion and three DOF for rotational motion,is established according to the K rchhoff motion equation.Since the flexible winged paafoil system flying at low altitude is more susceptibleto winds,the motion characteristics of the parafoil system Wth and Wthout winds are simulated and analyzed.Furthermore,the ardropm test is used to further verify the model.The comparison results show that the simulation trajectory roughly overlaps with the actual flight track.The horzontnl velocity of the simulation model is in good accordance with the airdrop test,with a deviation less than0.5m/s,while its simulated vertical velocity fuctuates slightly under the infuence of the wind,and shows a similar trend to the ardrop test.It is concludedthat the established model can well describe the characteristics of the parafoil system.展开更多
The omnidirectional legged vehicle with steering-rails has a specific mechanism feature,and it can be controlled flexibly and accurately in omnidirectional motion.Currently there lacks further research in this area.In...The omnidirectional legged vehicle with steering-rails has a specific mechanism feature,and it can be controlled flexibly and accurately in omnidirectional motion.Currently there lacks further research in this area.In this paper,the mechanical characteristics of independent walking control and steering control and its kinematics principle are introduced,and a vehicle has a composite motion mode of parallel link mechanism and steering mechanism is presented.The motion direction control of the proposed vehicle is only dependant on its steering rails,so its motion is simple and effective to control.When the relative motion between the walking and steering is controlled cooperatively,the vehicle can walk perfectly.By controlling the steering rails,the vehicle can walk along arbitrary trajectory on the ground.To achieve a good result of motion control,an equivalent manipulator model needs to be built.In terms of the mechanism feature and the kinematic principle,the simplified manipulator model consists of a rail in stance phase,a rail in swing phase,and an equivalent leg.Considering the ground surface slope during walking,a parameter of inclination angle is added.Based on such a RPP manipulator model,the equations of motion are derived by means of Lagrangian dynamic approach.To verify the dynamic equations,the motion of the manipulator model is simulated based on linear and nonlinear motion planning.With the same model and motion parameters,the dynamic equations can be solved by Matlab and the calculation data can be gained.Compared with the simulation data,the result confirms the manipulator dynamic equations are correct.As a result of such special characteristics of the legged mechanism with steering rails,it has a potential broad application prospects.The derivation of dynamics equation could benefit the motion control of the mechanism.展开更多
Due to the structural complexity, the dynamic modeling and quick performance evaluation for the parallel kinematic machines （PKMs） are still to be remained as two challenges in the stage of conceptual design. By usi...Due to the structural complexity, the dynamic modeling and quick performance evaluation for the parallel kinematic machines （PKMs） are still to be remained as two challenges in the stage of conceptual design. By using the finite element method and substructure synthesis, this paper mainly deals with the dynamic modeling and eigenvalue evaluation of a novel 3-DOF spindle head named the A3 head. The topological architecture behind the proposed A3 head is a 3-RPS parallel mechanism, which possesses one translational and two rotational capabilities. The mechanical features of the A3 head are briefly addressed in the first place followed by inverse position analysis. In the dynamic modeling, the platform is treated as a rigid body, the RPS limbs as the continuous uniform beams and the joints as lumped virtual springs. With the combination of substructure synthesis and finite element method, an analytical approach is then proposed to formulate the governing equations of motion of system using the compatibility conditions at interface between the limbs and the platform. Consequently, by solving the eigenvalue problem of the governing equations of motion, the distribution of lower natural frequencies of the A3 head throughout the entire workspace can be predicted in a quick manner. Modal analysis for the A3 head reveals that the distributions of lower natural frequencies are strongly related to the mechanism configuration and are axially symmetric due to system kinematic and structural features. The sensitivity analysis of the system indicates that the dimensional parameters of the 3-RPS mechanism have a slight effect on system lower natural frequencies while the joint compliances affect the distributions of lower natural frequencies significantly. The proposed dynamic modeling method can also be applied to other PKMs and can effectively evaluate the PKM＇s dynamic performance throughout the entire workspace.展开更多
A first principles-based dynamic model for a continuous catalyst regeneration (CCR) platforming process, the UOP commercial naphtha catalytic reforming process, is developed in this paper. The lumping details of the n...A first principles-based dynamic model for a continuous catalyst regeneration (CCR) platforming process, the UOP commercial naphtha catalytic reforming process, is developed in this paper. The lumping details of the naphtha feed and reaction scheme of the reaction model are given. The process model is composed of the reforming reaction model with catalyst deactivation, the furnace model and the separator model, which is capable of capturing the major dynamics that occurs in this process system. Dynamic simulations are performed based on Gear numerical algorithm and method of lines (MOL), a numerical technique dealing with partial differential equations (PDEs). The results of simulation are also presented. Dynamic responses caused by disturbances in the process system can be correctly predicted through simulations.展开更多
The object of study is about dynamic modeling and control for a 2degree-of-freedom (DOF) planar parallel mechanism (PM) with flexible links. The kinematic anddynamic equations are established according to the characte...The object of study is about dynamic modeling and control for a 2degree-of-freedom (DOF) planar parallel mechanism (PM) with flexible links. The kinematic anddynamic equations are established according to the characteristics of mixed rigid and flexiblestructure. By using the singular perturbation approach (SPA), the model of the mechanism can beseparated into slow and fast subsystems. Based on the feedback linearization theory and inputshaping technique, the large scale rigid motion controller and the flexible link vibrationcontroller can be designed separately to achieve fast and accurate positioning of the PM.展开更多
Clearance between the moving joints is unavoidable in real working process. At present, many researches are mainly focused on dynamics of plane revolute joint in plane mechanism, but few on dynamics of spatial spheric...Clearance between the moving joints is unavoidable in real working process. At present, many researches are mainly focused on dynamics of plane revolute joint in plane mechanism, but few on dynamics of spatial spherical joint clearance in spatial parallel mechanism. In this paper, a general method is proposed for establishing dynamic equations of spatial parallel mechanism with spatial spherical clearance by Lagrange multiplier method. The kinematic model and contact force model of the spherical joint clearance were established successively. Lagrange multiplier method was used to deduce the dynamics equation of 4 UPS-UPU mechanism with spherical clearance joint systematically. The influence of friction coefficient on dynamics response of 4 UPS-UPU mechanism with spherical clearance joint was analyzed. Non-linear characteristics of clearance joint and moving platform were analyzed by Poincare map, phase diagram, and bifurcation diagram. The results show that variation of friction coefficient and clearance value had little effect on stability of the mechanism, but the chaotic phenomenon was found at spherical clearance joint. The research has theoretical guiding significance for improving the dynamic performance and avoiding of chaos of parallel mechanisms including spherical joint clearance.展开更多
In this study,the Hamilton’s principle is applied to revisit the dynamic modeling of the cable-stayed beam,and the motion equations governing the nonlinear response of the cable-stayed beam are derived.The correspond...In this study,the Hamilton’s principle is applied to revisit the dynamic modeling of the cable-stayed beam,and the motion equations governing the nonlinear response of the cable-stayed beam are derived.The corresponding boundary terms are transformed to the dynamic equilibrium conditions through the continuity of the displacement at the anchoring point.Following the standard condensation procedure,the condensed model of the cable-stayed beam is determined.The eigenvalue analysis is performed to determine the closed-form eigenvalue solution of the linear problems,and two types of eigenvalue solution are obtained.It is shown that the frequency spectrum of the cable-stayed beam exhibits the curve veering and crossover phenomena.Corresponding to these phenomena,the mode shapes of the cable-stayed beam may exhibit the coupling characteristic.Finally,the discrete model of the cable-stayed beam is determined,and the possible nonlinear interactions are discussed.展开更多
The total ionizing dose(TID) effect is a key cause for the degradation/failure of semiconductor device performance under energetic-particle irradiation. We developed a dynamic model of mobile particles and defects by ...The total ionizing dose(TID) effect is a key cause for the degradation/failure of semiconductor device performance under energetic-particle irradiation. We developed a dynamic model of mobile particles and defects by solving the rate equations and Poisson's equation simultaneously, to understand threshold voltage shifts induced by TID in silicon-based metal–oxide–semiconductor(MOS) devices. The calculated charged defect distribution and corresponding electric field under different TIDs are consistent with experiments. TID changes the electric field at the Si/SiO_(2) interface by inducing the accumulation of oxide charged defects nearby, thus shifting the threshold voltage accordingly. With increasing TID, the oxide charged defects increase to saturation, and the electric field increases following the universal 2/3 power law. Through analyzing the influence of TID on the interfacial electric field by different factors, we recommend that the radiation-hardened performance of devices can be improved by choosing a thin oxide layer with high permittivity and under high gate voltages.展开更多
Aimed at the problems of design difficulty and weak kinematic performance caused by spherical joint,a novel PRC+PRCR+RR humanoid ankle joint based on the partially decoupled spherical parallel mechanism is proposed.Ac...Aimed at the problems of design difficulty and weak kinematic performance caused by spherical joint,a novel PRC+PRCR+RR humanoid ankle joint based on the partially decoupled spherical parallel mechanism is proposed.According to screw theory,the degree of freedom and decoupling characteristics of this mechanism are analyzed.Based on Klein formula and virtual work principle,the kinematic expressions of each link and dynamic model are established.The correctness of the dynamic model is verified by combining the virtual prototype software and the ankle pose function obtained by gait planning and Fourier fitting.The workspace of this mechanism is mapped into a two-dimensional polar coordinate system with the azimuth and elevation angles of the spherical coordinate system as parameters.The motion/force transmission index and constraint index of this mechanism are evaluated and expressed in the workspace,showing this mechanism with excellent kinematic characteristics.展开更多
This paper investigates steady-state and dynamic simulation of an industrial fixed-bed ethylene oxide reactor. A mathematical heterogeneous one-dimensional model is developed for simulation of reactor performance in t...This paper investigates steady-state and dynamic simulation of an industrial fixed-bed ethylene oxide reactor. A mathematical heterogeneous one-dimensional model is developed for simulation of reactor performance in the presence of long term deactivation of silver/a-alumina catalyst. In this paper, steady-state model of the reactor is solved and results of steady state simulation are fed to dynamic simulator as initial condition. When results of dynamic simulation are compared with industrial reactor data, it is found that there were good agreements between simulation results and industrial data. The proposed model is also validated by industrial process data for a period of 1100 operating days.展开更多
基金supported by grants from the Research Grant Council of the Hong Kong Special Administrative Region,China(Project No.HKU 17207518).
文摘This paper presents a dynamic modeling method to test and examine the minimum mass of pressurized pore-gas for triggering landslides in stable gentle soil slopes.A stable gentle soil slope model is constructed with a dry cement powder core,a saturated clay middle layer,and a dry sand upper layer.The test injects H_(2)O_(2)solution into the cement core to produce new pore-gas.The model test includes three identical H_(2)O_(2)injections.The small mass of generated oxygen gas(0.07%of slope soil mass and landslide body)from the first injection can build sufficient pore-gas pressure to cause soil upheaval and slide.Meanwhile,despite the first injection causing leak paths in the clay layer,the generated small mass of gas from the second and third injections can further trigger the landslide.A dynamic theoretical analysis of the slope failure is carried out and the required minimum pore-gas pressure for the landslide is calculated.The mass and pressure of generated gas in the model test are also estimated based on the calibration test for oxygen generation from H_(2)O_(2)solution in cement powder.The results indicate that the minimum mass of the generated gas for triggering the landslide is 2 ppm to 0.07%of the landslide body.Furthermore,the small mass of gas can provide sufficient pressure to cause soil upheaval and soil sliding in dynamic analysis.
基金Project supported by the National Science and Technology Major Project(No.J2022-IV-0005-0022)the Aero Science Foundation of China(No.20230015050001)the Shenyang Science and Technology Plan Project of China(No.24-202-6-01)。
文摘As a common fault of the aero-engine,the blade-casing rubbing(BCR)has the potential to cause catastrophic accidents.In this paper,to investigate the dynamic responses and wear characteristics of the system,the laminated shell element is used to establish the finite element model(FEM)of a flexibly coated casing system.Using the shell element,the blade is modeled,and the surface stress of the blade is calculated.The stress-solving method of the blade is validated through comparisons with the measured time-domain waveform of the stress.Then,a dynamic model of a blade-flexibly coated casing system with rubbing is proposed,accounting for the time-varying mass and stiffness of the casing caused by coating wear.The effects of the proposed flexible casing model are compared with those of a rigid casing model,and the stress changes induced by rubbing are investigated.The results show that the natural characteristics of the coated casing decrease due to the coating wear.The flexibly coated casing model is found to be more suitable for studying casing vibration.Additionally,the stress changes caused by rubbing are slight,and the change in the stress maximum is approximately 5%under the influence of the abrasive coating.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
基金supported by the National Natural Science Foundation of China(Grant Nos. 50835006 and 51005161)the Science & Technology Support Planning Foundation of Tianjin(Grant No. 09ZCKFGX03000)the Natural Science Foundation of Tianjin(Grant No. 09JCZDJC23400)
文摘PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.
基金supported by National Natural Science Foundation of China(No.11772089)Fundamental Research Funds for the Central Universities(Nos.N170308028,N170306004 and N180708009)Program for the Innovative Talents of Higher Learning Institutions of Liaoning(LR2017035)。
文摘There exists a lot of research on the nonlinear vibration of the pipeline system with different boundary conditions.To the best of our knowledge,little research on the actual constraint of the clamp has been performed.In this paper,according to hysteresis loops of the clamp obtained from experimental test,the simplified bilinear stiffness and damping model is proposed.Then the Finite Element(FE)model of L-type pipeline system with clamps is established using Timoshenko beam theory in combination with aforementioned stiffness-damping model.Both hammering and shaker tests verify the FE model via the comparisons of natural frequencies and vibration responses.The results show that the maximum errors of natural frequencies and vibration responses are about 8.31%and 17.6%,respectively.The proposed model can simulate the dynamic characteristics of the L-type pipeline system with clamps well,which is helpful to provide some guidance for the early design stage of pipeline in aero-engine.
基金supported by the National Natural Science Foundation of China (Grant No.50835006)the Natural Science Foundation of Tianjin (Grant No.09JCZDJC23400)
文摘For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.
文摘Cyclic total reflux(CTR) batch distillation is a promising mode of the process but lacking of appropriate modeling for the period of filling the reflux drum.A new dynamic modeling method for the simulation of CTR batch distillation is proposed in this work,in which the changes in column holdup and liquid flow rate during the filling of the drum,and the consequent change in valid number of theoretical plates are considered.The effect of drum holdup on operation time is investigated and the optimal drum holdup is obtained from the simulation.The dynamic modeling is compared to the conventional modeling without consideration of change in liquid flow rate. The experimental result shows that the present modeling is more reliable and more accurate,especially for the column with large liquid holdup.
基金supported by National Science and Technology Major Project of China(Grant Nos.2010ZX04017-013,2010ZX04004-112)National Natural Science Foundation of China(Grant No.51205248)+1 种基金Shanghai Municipal Natural Science Foundation of China(Grant No.12ZR1445200)Doctoral Programs Foundation of Ministry of Education of China(Grant No.20120073120060)
文摘The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.
基金The National Natural Science Foundation of China(No.61273138,61573197)the National Key Technology R&D Program(No.2015BAK06B04)+1 种基金the Key Fund of Tianjin(No.14JCZDJC39300)the Key Technologies R&D Program of Tianjin(No.14ZCZDSF00022)
文摘In order to better study the dynamic characteristics and the control strategy of parafoil systems,considering the effect of flap deflection as the control mechanism and regarding the parafoil and the payload as a rigid body,a six degrees-of-freedom(DOF)dynamic model of a parafoil system including three DOF for translational motion and three DOF for rotational motion,is established according to the K rchhoff motion equation.Since the flexible winged paafoil system flying at low altitude is more susceptibleto winds,the motion characteristics of the parafoil system Wth and Wthout winds are simulated and analyzed.Furthermore,the ardropm test is used to further verify the model.The comparison results show that the simulation trajectory roughly overlaps with the actual flight track.The horzontnl velocity of the simulation model is in good accordance with the airdrop test,with a deviation less than0.5m/s,while its simulated vertical velocity fuctuates slightly under the infuence of the wind,and shows a similar trend to the ardrop test.It is concludedthat the established model can well describe the characteristics of the parafoil system.
基金supported by National Hi-tech Research and Development Program of China(863 Program,Grant No.2007AA11Z244)
文摘The omnidirectional legged vehicle with steering-rails has a specific mechanism feature,and it can be controlled flexibly and accurately in omnidirectional motion.Currently there lacks further research in this area.In this paper,the mechanical characteristics of independent walking control and steering control and its kinematics principle are introduced,and a vehicle has a composite motion mode of parallel link mechanism and steering mechanism is presented.The motion direction control of the proposed vehicle is only dependant on its steering rails,so its motion is simple and effective to control.When the relative motion between the walking and steering is controlled cooperatively,the vehicle can walk perfectly.By controlling the steering rails,the vehicle can walk along arbitrary trajectory on the ground.To achieve a good result of motion control,an equivalent manipulator model needs to be built.In terms of the mechanism feature and the kinematic principle,the simplified manipulator model consists of a rail in stance phase,a rail in swing phase,and an equivalent leg.Considering the ground surface slope during walking,a parameter of inclination angle is added.Based on such a RPP manipulator model,the equations of motion are derived by means of Lagrangian dynamic approach.To verify the dynamic equations,the motion of the manipulator model is simulated based on linear and nonlinear motion planning.With the same model and motion parameters,the dynamic equations can be solved by Matlab and the calculation data can be gained.Compared with the simulation data,the result confirms the manipulator dynamic equations are correct.As a result of such special characteristics of the legged mechanism with steering rails,it has a potential broad application prospects.The derivation of dynamics equation could benefit the motion control of the mechanism.
基金supported by National Natural Science Foundation ofChina (Grant No.50535010,Grant No.50775158)National Scienceand Technology Supporting Plan of China (Grant No.2006BAF01B00)
文摘Due to the structural complexity, the dynamic modeling and quick performance evaluation for the parallel kinematic machines （PKMs） are still to be remained as two challenges in the stage of conceptual design. By using the finite element method and substructure synthesis, this paper mainly deals with the dynamic modeling and eigenvalue evaluation of a novel 3-DOF spindle head named the A3 head. The topological architecture behind the proposed A3 head is a 3-RPS parallel mechanism, which possesses one translational and two rotational capabilities. The mechanical features of the A3 head are briefly addressed in the first place followed by inverse position analysis. In the dynamic modeling, the platform is treated as a rigid body, the RPS limbs as the continuous uniform beams and the joints as lumped virtual springs. With the combination of substructure synthesis and finite element method, an analytical approach is then proposed to formulate the governing equations of motion of system using the compatibility conditions at interface between the limbs and the platform. Consequently, by solving the eigenvalue problem of the governing equations of motion, the distribution of lower natural frequencies of the A3 head throughout the entire workspace can be predicted in a quick manner. Modal analysis for the A3 head reveals that the distributions of lower natural frequencies are strongly related to the mechanism configuration and are axially symmetric due to system kinematic and structural features. The sensitivity analysis of the system indicates that the dimensional parameters of the 3-RPS mechanism have a slight effect on system lower natural frequencies while the joint compliances affect the distributions of lower natural frequencies significantly. The proposed dynamic modeling method can also be applied to other PKMs and can effectively evaluate the PKM＇s dynamic performance throughout the entire workspace.
文摘A first principles-based dynamic model for a continuous catalyst regeneration (CCR) platforming process, the UOP commercial naphtha catalytic reforming process, is developed in this paper. The lumping details of the naphtha feed and reaction scheme of the reaction model are given. The process model is composed of the reforming reaction model with catalyst deactivation, the furnace model and the separator model, which is capable of capturing the major dynamics that occurs in this process system. Dynamic simulations are performed based on Gear numerical algorithm and method of lines (MOL), a numerical technique dealing with partial differential equations (PDEs). The results of simulation are also presented. Dynamic responses caused by disturbances in the process system can be correctly predicted through simulations.
基金This project is supported by National Natural Science Foundation of China (No.50390064, No.50375099) Doctorate Foundation of Ministry of Education of China(No.20020248048).
文摘The object of study is about dynamic modeling and control for a 2degree-of-freedom (DOF) planar parallel mechanism (PM) with flexible links. The kinematic anddynamic equations are established according to the characteristics of mixed rigid and flexiblestructure. By using the singular perturbation approach (SPA), the model of the mechanism can beseparated into slow and fast subsystems. Based on the feedback linearization theory and inputshaping technique, the large scale rigid motion controller and the flexible link vibrationcontroller can be designed separately to achieve fast and accurate positioning of the PM.
基金Sponsored by the Natural Science Foundation of Shandong Province(Grand No.ZR2017MEE066)the Shandong Key Research and Development Public Welfare Program(2019GGX104001)。
文摘Clearance between the moving joints is unavoidable in real working process. At present, many researches are mainly focused on dynamics of plane revolute joint in plane mechanism, but few on dynamics of spatial spherical joint clearance in spatial parallel mechanism. In this paper, a general method is proposed for establishing dynamic equations of spatial parallel mechanism with spatial spherical clearance by Lagrange multiplier method. The kinematic model and contact force model of the spherical joint clearance were established successively. Lagrange multiplier method was used to deduce the dynamics equation of 4 UPS-UPU mechanism with spherical clearance joint systematically. The influence of friction coefficient on dynamics response of 4 UPS-UPU mechanism with spherical clearance joint was analyzed. Non-linear characteristics of clearance joint and moving platform were analyzed by Poincare map, phase diagram, and bifurcation diagram. The results show that variation of friction coefficient and clearance value had little effect on stability of the mechanism, but the chaotic phenomenon was found at spherical clearance joint. The research has theoretical guiding significance for improving the dynamic performance and avoiding of chaos of parallel mechanisms including spherical joint clearance.
基金supported by Natural Science Foundation of Hunan Province(Grant 2018JJ2029)Scientific Research Fund of Hunan Provincial Education Department(Grant 19B192).
文摘In this study,the Hamilton’s principle is applied to revisit the dynamic modeling of the cable-stayed beam,and the motion equations governing the nonlinear response of the cable-stayed beam are derived.The corresponding boundary terms are transformed to the dynamic equilibrium conditions through the continuity of the displacement at the anchoring point.Following the standard condensation procedure,the condensed model of the cable-stayed beam is determined.The eigenvalue analysis is performed to determine the closed-form eigenvalue solution of the linear problems,and two types of eigenvalue solution are obtained.It is shown that the frequency spectrum of the cable-stayed beam exhibits the curve veering and crossover phenomena.Corresponding to these phenomena,the mode shapes of the cable-stayed beam may exhibit the coupling characteristic.Finally,the discrete model of the cable-stayed beam is determined,and the possible nonlinear interactions are discussed.
基金Project supported by the Science Challenge Project of China (Grant No.TZ2018004)the National Natural Science Foundation of China (Grant Nos.11975018 and 11775254)+1 种基金the National MCF Energy R&D Program of China (Grant No.2018YEF0308100)the outstanding member of Youth Innovation Promotion Association CAS (Grant No.Y202087)。
文摘The total ionizing dose(TID) effect is a key cause for the degradation/failure of semiconductor device performance under energetic-particle irradiation. We developed a dynamic model of mobile particles and defects by solving the rate equations and Poisson's equation simultaneously, to understand threshold voltage shifts induced by TID in silicon-based metal–oxide–semiconductor(MOS) devices. The calculated charged defect distribution and corresponding electric field under different TIDs are consistent with experiments. TID changes the electric field at the Si/SiO_(2) interface by inducing the accumulation of oxide charged defects nearby, thus shifting the threshold voltage accordingly. With increasing TID, the oxide charged defects increase to saturation, and the electric field increases following the universal 2/3 power law. Through analyzing the influence of TID on the interfacial electric field by different factors, we recommend that the radiation-hardened performance of devices can be improved by choosing a thin oxide layer with high permittivity and under high gate voltages.
基金the Zhejiang Province Foundation for Distinguished Young Scholars of China(No.LR18E050003)the National Natural Science Foundation of China(Nos.51975523 and 51475424)。
文摘Aimed at the problems of design difficulty and weak kinematic performance caused by spherical joint,a novel PRC+PRCR+RR humanoid ankle joint based on the partially decoupled spherical parallel mechanism is proposed.According to screw theory,the degree of freedom and decoupling characteristics of this mechanism are analyzed.Based on Klein formula and virtual work principle,the kinematic expressions of each link and dynamic model are established.The correctness of the dynamic model is verified by combining the virtual prototype software and the ankle pose function obtained by gait planning and Fourier fitting.The workspace of this mechanism is mapped into a two-dimensional polar coordinate system with the azimuth and elevation angles of the spherical coordinate system as parameters.The motion/force transmission index and constraint index of this mechanism are evaluated and expressed in the workspace,showing this mechanism with excellent kinematic characteristics.
文摘This paper investigates steady-state and dynamic simulation of an industrial fixed-bed ethylene oxide reactor. A mathematical heterogeneous one-dimensional model is developed for simulation of reactor performance in the presence of long term deactivation of silver/a-alumina catalyst. In this paper, steady-state model of the reactor is solved and results of steady state simulation are fed to dynamic simulator as initial condition. When results of dynamic simulation are compared with industrial reactor data, it is found that there were good agreements between simulation results and industrial data. The proposed model is also validated by industrial process data for a period of 1100 operating days.
